Upper
BCM M4 Upper Receiver Assembly (w/ Laser T-Markings)
BCM's M4 flat-top upper receiver, "Precision machined to correct Mil-Specs from 7075 T6 Forgings" and sold "Fully Assembled with forward assist, and ejection port cover": a "Mil-Std 1913 Rail" of 13 slots with "Laser etched T-markings" (T2 to T12, in every other slot), "Machined for use with barrels that use an M4 barrel extension". No barrel, bolt carrier group or charging handle.

- Weight
- 9.59 oz ± 0.005 oz Conflictpublished: Big Tex Ordnance, BCM M4 Upper Receiver Assembly (w/ Laser T-Markings) (BCM4-UR-M4), Additional information, a seller, read Oct 5, 2026Its sources span 9.59 oz to 11.01 oz.
- Lowest price
- $129.00 at BCM, read Nov 21, 2026, out of stock that day
- Maker's number
- BCM4-UR-M4
- Colour
- Black (placeholder)
- Drawn as
- modelled
- Maker's page
- bravocompanyusa.com
In “BCM 16 in mid-length”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
The receiver's length, rear face to the end of the barrel-nut thread7.657 in ± 0.01 in 194.5 mmConfirmedWorked out: {.front_face_x} - {.receiver_rear_x}
Worked out 7.657 in ± 0.01 in used
{.front_face_x} - {.receiver_rear_x}, harvested
The Army's drawing: 6.999 −.006 behind the pivot lug's hole and .661 ± .003 ahead of it.
Published “Dimensions 7.67 × 2.31 × 2.31 in”
AR15Discounts, BCM GUNFIGHTER Assembled Upper Receiver (MPN BCM4-UR-M4), Additional information, a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
The first of three; the page doesn't say what each spans. It is the receiver alone: the forward assist's cap stands another 0.3 in behind the rear face.
The drawing dimensions both faces; the seller's figure agrees within its ±.
A check of the drawing's two ends against a seller's figure for this part: they agree within 0.013 in.
The receiver's height, the lugs' undersides to the rail's top2.306 in ± 0.025 in 58.6 mmCorroboratedWorked out: {.rail_top_above_pin} + {.lug_bottom_below_pin}
Published “Dimensions 7.67 × 2.31 × 2.31 in”
AR15Discounts, BCM GUNFIGHTER Assembled Upper Receiver (MPN BCM4-UR-M4), Additional information, a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
The second of three (the third repeats it and isn't the width: the forward assist's housing and the deflector reach 1.9 across).
Worked out 2.306 in ± 0.025 in used
{.rail_top_above_pin} + {.lug_bottom_below_pin}, harvested
The rail's top above the pin line and the lugs' undersides below it.
The two figures it is the sum of are each sourced; the seller's 2.31 agrees within 0.004.
The lugs' undersides below the pin line0.216 in ± 0.008 in 5.5 mmConfirmedStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-1/3, Section A-A, and F-2/3, side elevation; user-supplied scan (Distribution Statement F), PDF pages 123 and 124
Standard “.476 −.015 (the front lug), .471 −.010 (the rear), from -G-; lug holes .2525 ± .0015 below -G-” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-1/3, Section A-A, and F-2/3, side elevation; user-supplied scan (Distribution Statement F), PDF pages 123 and 124, from the site owner
-G- is the flat underside. The front lug reaches .461 to .476 below it, the rear .461 to .471: the middle of the two, less the holes' .2525.
Photo 0.217 in ± 0.02 in
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 127.86 px/in in the mid-plane; the lens 4 to 5 in above the pin line, about 38 in away. Read by the traced outline's lowest point, 0.247 below the pin line (0.233 in the left photo): the lugs' near lower edges, 0.25 nearer the lens and seen from above, which read 0.03 low
The drawing dimensions it; the photo agrees within its ±.
Bore axis above the takedown pin centre0.877 in ± 0.0015 in 22.3 mmConfirmedWorked out: {std.ar15.bore_axis_y}
Worked out 0.8775 in ± 0.0015 in used
{std.ar15.bore_axis_y}, harvested
The standard's: BCM's page says it is "Precision machined to correct Mil-Specs" and "Built to the correct Mil-Specs". Not measured on this upper.
The receiver's rear face behind the takedown pin (negative)-0.621 in ± 0.005 in -15.8 mmConfirmedWorked out: {std.ar15.upper_rear_face_x}
Worked out -0.621 in ± 0.005 in used
{std.ar15.upper_rear_face_x}, harvested
The Army's drawing (8448524 and 12576280 alike: 6.999 −.006 behind the pivot lug's hole).
Photo -0.61 in ± 0.03 in
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 127.86 px/in in the mid-plane; the lens about 38 in away over x 2.2 (the far rims' offsets in the two holes: 35.5 in, x 2.18). Read by the silhouette's rear end over y 1.1 to 1.5 reads -0.646 to -0.666: the round body's near edge, 0.59 nearer the lens, which reads 1.6% long about the lens's foot: 2.2 + (-0.656 - 2.2) / 1.016
The drawing dimensions the face; the photo, read through its lens, agrees within its ±.
The receiver's front face (the end of its barrel-nut thread) ahead of the takedown pin7.036 in ± 0.005 in 178.7 mmConfirmedWorked out: {std.ar15.upper_front_face_x}
Worked out 7.036 in ± 0.005 in used
{std.ar15.upper_front_face_x}, harvested
The Army's drawing: .661 ± .003 ahead of the pivot lug's hole.
Photo 7.04 in ± 0.04 in
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 127.86 px/in in the mid-plane; the lens about 38 in away over x 2.2. Read by the silhouette's front end reads 7.12: the thread's near rim, 0.62 nearer the lens (its front face shows as an ellipse 0.09 in across), 1.6% long about the lens's foot: 2.2 + (7.12 - 2.2) / 1.016
The drawing dimensions the face; the silhouette's end is the thread's near rim, and through the lens it agrees within its ±.
The body's front shoulder, where the barrel-nut thread begins, ahead of the takedown pin6.591 in ± 0.012 in 167.4 mmConfirmedWorked out: {.front_face_x} - {std.ar15.upper_barrel_thread_length}
Worked out 6.591 in ± 0.012 in used
{.front_face_x} - {std.ar15.upper_barrel_thread_length}, harvested
The Army's .445 REF behind the front face (8448524; the M16A2's 12576280 gives the nose as .440 +.010).
Photo 6.59 in ± 0.03 in
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 127.86 px/in in the mid-plane; the lens about 38 in away over x 2.2. Read by the body's front face above and below the thread reads 6.653 at every height (one vertical line with the rail's front end): its near edge, 0.59 nearer the lens; 2.2 + (6.653 - 2.2) / 1.0155
The drawing; the photo through its lens lands on it.
The receiver's underside above the pin line0.248 in ± 0.0015 in 6.3 mmConfirmedWorked out: {std.ar15.deck_y}
Worked out 0.2485 in ± 0.0015 in used
{std.ar15.deck_y}, harvested
It sits on the lower's deck (the M16A2's drawing: lug holes .2525 ± .0015 below the underside -G-).
Photo 0.245 in ± 0.02 in
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 127.86 px/in in the mid-plane; the lens 4.0 to 5.2 in above the pin line, 35.5 to 38 in away (the far rims' offsets in the two holes; the hinge pin's height). Read by the underside's edge between the lugs reads 0.193 above the pin line (a line fitted over 750 columns, rms 0.5 px): its near edge, 0.453 nearer the lens, seen from above; through the lens 0.241 to 0.252
Why no height is taken from this photo as it reads.
The drawing; the photo lands on it only through its lens.
Width of the receiver's round body1.19 in ± 0.01 in 30.2 mmConfirmedStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, Section D-D, and F-3/3, Section H-H; user-supplied scan (Distribution Statement F), PDF pages 124 and 126
Standard “(1.19) FORGED ∅ -B-” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, Section D-D, and F-3/3, Section H-H; user-supplied scan (Distribution Statement F), PDF pages 124 and 126, from the site owner
Standard “FORGED DIA 1.18 DIA REF -V-”
US Army TDP drawing 8448524 (Receiver, Upper), sheet 2 of 2, rev G: View G-G; user-supplied scan, a copy on file, from the site owner
Photo 1.2 in ± 0.025 in
BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400, harvested
Scale: the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top (rms 0.5 px); 118.2 px/in at the bore's height, by the forward assist's cap (.605 across, 9349084: 71.5 px). Read by the body's two edges between the deflector and the forward assist's housing, 141 px apart; the ± is the lens's height (117 to 119 px/in)
The drawing of the receiver the flat top derives from; the older drawing reads .01 less and BCM's own part from above .01 more, each within its ±.
The forging's drawing isn't in the package; both machined drawings give the round body's forged diameter as a reference. Its forward assist's housing, its deflector and the port cover's hinge stand out past it on the right.
The round body's radius about the bore0.595 in ± 0.005 in 15.1 mmConfirmedWorked out: {.width} / 2
Worked out 0.595 in ± 0.005 in used
{.width} / 2, harvested
Model 0.6 in ± 0.003 in
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; a working script), cut at x 1.8: cylindrical faces r 0.6000 about the bore's axis
The drawing's forged figure; the model's is 0.005 more.
The bore the bolt carrier runs in1.001 in ± 0.001 in 25.4 mmConfirmedStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-3/3, front view; user-supplied scan (Distribution Statement F), PDF page 126
Standard “1.000 +.002 ∅ FIRST 1.110 +.030; 1.000 +.006 ∅ THRU REMAINDER” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-3/3, front view; user-supplied scan (Distribution Statement F), PDF page 126, from the site owner
The two lugs' width0.494 in ± 0.0015 in 12.6 mmConfirmedStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, rear view; user-supplied scan (Distribution Statement F), PDF page 124
Standard “.496 −.003 BOTH LUGS” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, rear view; user-supplied scan (Distribution Statement F), PDF page 124, from the site owner
The two lugs' pin holes0.251 in ± 0.0015 in 6.4 mmConfirmedStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-1/3, Section A-A, and F-2/3, side elevation; user-supplied scan (Distribution Statement F), PDF pages 123 and 124
Standard “.250 +.001 ∅ THRU (the pivot lug's); .250 +.002 ∅ THRU, C'SINK .30 +.02 ∅ X 88° +4° INCL THIS SIDE ONLY (the takedown lug's)” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-1/3, Section A-A, and F-2/3, side elevation; user-supplied scan (Distribution Statement F), PDF pages 123 and 124, from the site owner
One figure for both; the takedown lug's countersink isn't drawn. In Primary Arms' photos both holes are see-through, 32 px across at 128 px/in.
The top rail's surface above the pin line2.09 in ± 0.02 in 53.1 mmCorroboratedPhoto: Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768
Photo 2.09 in ± 0.02 in used
Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane; the lens 35 in away, 3.3 in above the pin line over x 3.9 (the far rims' offsets in the two holes). Read by a line through the tooth tops (349 columns, rms 0.15 px) stands 2.078 above the pin line at mid-length; through the lens 2.090
Photo 2.09 in ± 0.02 in
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 127.86 px/in in the mid-plane; the lens 4.0 to 5.2 in above the pin line, 35.5 to 38 in away. Read by a line through the tooth tops (314 columns, rms 0.13 px) stands 2.068 above the pin line at mid-length; through the lens 2.086 to 2.094
Model 2.09 in ± 0.003 in
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text in the rifle frame its lug holes set: the teeth's top planes at y 2.0900
The photo whose lens stood lowest (the least to correct); the right photo and the reference model of a mil-spec flat top give the same figure.
Each photo reads the top flat's near edge, 0.318 nearer the lens and seen from above: 2.068 and 2.078 as they stand.
How many rail slots13ProvisionalPhoto: Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768
Photo 13 count used
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins. Read by the gaps between the teeth along the top edge, counted (13 in the left photo and in BCM's banner from above too)
BCM's laser T-marks are in the even ones, T2 to T12 (its banner from above: T2 in the second slot from the rear): slot n, counted from 0 at the rear, is T(n + 1).
The rearmost rail slot's centre ahead of the takedown pin1.31 in ± 0.02 in 33.3 mmCorroboratedPhoto: Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768
Photo 1.31 in ± 0.02 in used
Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 137.71 px/in; the 13 slots' centres 0.4008 apart in that frame (std.picatinny.slot_pitch: x 1.0173); the lens over x 3.9 (the far rims' offsets in the two holes). Read by the 13 gaps' centres at the 50% level, the rearmost at 1.263: 3.91 + (1.263 - 3.91) / 1.0173 = 1.308; the ± is the lens's foot (± 0.7 in)
Photo 1.32 in ± 0.02 in
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 127.86 px/in; the 13 slots' centres 0.4006 apart in that frame (x 1.0168); the lens over x 2.2. Read by the rearmost gap's centre at 1.308: 2.18 + (1.308 - 2.18) / 1.0168 = 1.322; with the foot anywhere from x 1.45 to 2.4, 1.310 to 1.326
Model 1.308 in ± 0.003 in
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text in the rifle frame its lug holes set: 13 slots, their walls from x 1.2033 / 1.4133 to 5.9313 / 6.1413 at a 0.394 pitch
Its lens stood nearest the rail's middle, so what the lens's place leaves unsure moves this slot least. The right photo reads 0.01 more and the reference model of a mil-spec flat top 0.002 less: three that agree within their ±.
In these photos the far teeth are blown out to the background's white, so the dark teeth are the rail's near edge, 0.42 nearer the lens: the slots' pitch reads 1.7% long in the pins' frame, and their places are taken about the lens's foot at the pitch the standard gives.
The top rail's head: where it begins ahead of the tongue, X (the app draws the head from here)0.416 in ± 0.006 in 10.6 mmProvisionalWorked out: {std.ar15.rail_tongue_shoulder_x}
Worked out 0.4165 in ± 0.006 in used
{std.ar15.rail_tongue_shoulder_x}, from the site owner
Until 2026-10-20 this was the rail's rearmost point (now rail_tongue_rear_x), and the app drew the head at its full width from there, square: the charging handle's T, cut round for a rounded rail end, stood in its corners. Behind this the rail is the standard's tongue (std.ar15.rail_tongue_*), which the receiver's model carries, as the 22RB's does.
The top rail's tongue: its rounded end's rearmost point, X ahead of the takedown pin-0.62 in ± 0.02 in -15.7 mmCorroboratedPhoto: BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400
Photo -0.62 in ± 0.02 in used
BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400, harvested
Scale: the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top (rms 0.5 px), the rearmost slot's centre at px 842.0 as rail_slot0_x. Read by the rounded end's apex at px 1076.1: 1.930 behind the rearmost slot's centre
Model -0.625 in ± 0.003 in
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text in the rifle frame its lug holes set: the rail's top plane from x -0.625 (its rear face) to 1.203
The view that sees the end itself, on BCM's own part; the reference model agrees within 0.005.
Behind the first slot the rail runs solid over the charging handle's channel to an end rounded in plan, level with the receiver's rear face at its middle. (Primary Arms' right view reads that end's near corner, 0.29 off the middle: -0.595 as it stands, -0.57 through its lens, 0.05 ahead of the apex as the banner shows the rounding. Another point of the same end, so not a second measurement of this one.)
The top rail's front end ahead of the takedown pin6.593 in ± 0.02 in 167.5 mmCorroboratedPhoto: Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768
Photo 6.593 in ± 0.02 in used
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens about 38 in away over x 2.2; the teeth's near edge reads x 1.0168 (the slots' pitch). Read by the last tooth's front reads 6.6675: 2.18 + (6.6675 - 2.18) / 1.0168
Model 6.591 in ± 0.003 in
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text in the rifle frame its lug holes set: the last tooth from x 6.141 to 6.591, its shoulder's plane
BCM's own part; the reference model agrees within 0.002.
Level with the body's front shoulder (shoulder_x): one vertical line in the side photo.
The charging handle's channel above the bore's axis0.856 in ± 0.007 in 21.8 mmConfirmedWorked out: {std.ar15.charging_handle_axis_y} - {.bore_axis_above_pin}
Photo 0.9 in ± 0.05 in
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens 4 to 5 in above the pin line, about 38 in away. Read by the see-through notch in the rear end, from the ledge under it (reads 1.594: its far edge, through the lens 1.62 to 1.64) to the rail's underside (reads 1.899: its near edge, 1.92): the middle, 1.775, less the bore's 0.8775
Worked out 0.8563 in ± 0.007 in used
{std.ar15.charging_handle_axis_y} - {.bore_axis_above_pin}, from the site owner
Riding on its guide lugs on the channel's tier: std.ar15.charging_handle_axis_y.
A handle rides on its guide lugs on the channel's tier (std.ar15.charging_handle_axis_y, the Army's drawing's); the photo reads the see-through notch's middle, which is the room the handle's block lies in and not what it rides on. At 0.9 every handle's top stood 0.024 in the channel's roof (2026-10-20).
The gap under the rail's rear end where the handle's T lies: its middle. (The slot through the rear face is taller: from the bore's top to its roof, std.ar15.charging_handle_channel_roof_y; the catalog's other forged upper is placed by the open notch too.)
The charging handle's seat: the front wall of the open notch under the rail's rear end, ahead of the takedown pin0.068 in ± 0.02 in 1.7 mmCorroboratedPhoto: Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768
Photo 0.068 in ± 0.02 in used
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens 4 to 5 in above the pin line, about 38 in away. Read by the see-through notch's front wall in the traced outline (profiles.side): its flat at x 0.068 from y 1.657 to 1.775, between two corners cut back to x 0.017 and -0.023. What shows through a notch is bounded by the wall's near edge, half the receiver's width nearer the lens: from 38 in that reads 0.02 to 0.04 behind the wall itself, which ± covers on the one side
Standard 0.075 in ± 0.015 in
US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation, scaled (the notch has no callout in this view); user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Scaled, not a callout. On the 6600 px scan the two lug holes, fitted as circles, are 1966 px apart (308.4 px/in over std.ar15.pin_spacing) and the notch's front wall (column 2427.5) is 21.5 px ahead of the takedown hole's centre: 0.070. From the rear face's line, 217 px behind the wall, it is 0.083: the drawing dimensions that face at -0.621 and the scan has it at -0.634 by the holes. Between the two; ± covers both. The notch is 0.31 to 0.32 high there, for the handle's .2985 (drawing 8448518), its front corners cut back 0.06.
This receiver's own notch, where its model's wall is: a handle seated there stands in nothing. The Army's drawing, scaled, reads 0.007 more: within both ±.
Where a charging handle stops. The notch is cut across the receiver under the rail's rear end and is open to the rear: the handle's block (its T ahead of the wings or latches, as thick as the shaft) lies in it with its shoulder against this wall, and the shaft runs on through the slot ahead of it. Until 2026-10-05 the handle was placed with its shoulder at the rear face, 0.69 in behind this (that day's review of the models: its whole T hung behind the receiver, over the castle nut). A handle of the Army's length seated here ends 0.03 short of where the reference model's channel does (the front round's front, std.ar15.charging_handle_channel_front_round_x and _round_r, 5.9925, less 5.895 is 0.098). Magpul's photo of a handle in a receiver (a copy on file) has it so: the T's wing astride the rear face, the notch filled to its front wall.
The left side photo: where its lens stands, X3.9 in ± 0.7 in 99.1 mmProvisionalPhoto: Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768
Photo 3.9 in ± 0.7 in used
Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane. Read by the far rims' offsets in the two holes, as rail_slot0_x states it: the lens over x 3.9, its foot ± 0.7
A property of Primary Arms' photo b3b8d1ad9d16: what stands nearer the lens than the mid-plane reads large about this point (rail_slot0_x and rail_top_above_pin are read through the same lens).
The left side photo: where its lens stands, Y3.3 in ± 0.7 in 83.8 mmProvisionalPhoto: Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768
Photo 3.3 in ± 0.7 in used
Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane. Read by as left_photo_lens_x: 3.3 in above the pin line, as rail_top_above_pin states it (through it the tooth tops' 2.078 is 2.090); its ± taken as the foot's along the receiver
The left side photo: its lens's distance from the receiver's mid-plane35 in ± 10 in 889 mmProvisionalPhoto: Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768
Photo 35 in ± 10 in used
Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane. Read by as left_photo_lens_x: 35 in away, as rail_top_above_pin states it. The rail's near teeth, 0.42 nearer the lens, read 1.73% long in this frame (rail_slot0_x), which would make it 25: ± covers both, and moves what is read on the left wall by up to 0.007 in and the pad's foot by up to 0.011
The cam pin's pad on the left side, its face out from the middle (Z, to the left)0.563 in ± 0.003 in 14.3 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging
Model 0.5625 in ± 0.003 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text in the rifle frame its lug holes set: the round along the pad's top edge, r 0.0938 about an axis along x at (y 1.486, z -0.469), so its face at z -0.563; expo-arms-stripped-upper.cam_pad_face_z reads the same file's flat face at z -0.561 to -0.564 over x 4.60 to 5.58, y 1.05 to 1.63
The pad is the forging's: the Army's machined drawing doesn't show it (8448524 draws the right side, and the left only at the notch, View C-C). BCM's left photo has its foot at x 4.53 to 5.64, y 1.10 to 1.67 once brought back through the lens (profiles.left, cam_pin_pad); the reference model's flat face, x 4.60 to 5.58 and y 1.05 to 1.63, lies inside that foot but for its lower edge, 0.05 lower, where the photo's is in shadow and the face runs into the round body.
The cam pin's pad, the round between its face and its foot: how far the face's edge lies inside the foot0.115 in ± 0.02 in 2.9 mmCorroboratedPhoto: Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768
Photo 0.115 in ± 0.02 in used
Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Read by the face's edge is the bright line inside the foot's soft one: columns 233.5 and 354.5 to 357 against the foot's 218.5 and 372.5 on rows 350 to 380, row 340.5 against the foot's 323.5 on columns 260 to 330: 15, 15.5 to 18 and 17 px, 0.109 to 0.131 in the mid-plane's scale, 1.6% less through the lens at the face's depth
Model 0.094 in ± 0.003 in
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text in the rifle frame its lug holes set: the round along the pad's top edge, r 0.0938 about (y 1.486, z -0.469), and its two upper corners' rounds about z, r 0.0938 at x 4.695 and 5.488
BCM's own pad as its photo shows it; the reference model's round is 0.021 less, at the edge of the photo's ±.
The charging handle latch's slot in the left wall: the wall left between it and the notch's front wall (handle_seat_x)0.156 in ± 0.005 in 4 mmConfirmedStandard: US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: Section D-D (cut along the notch's centre line, View C-C: the left wall at the rear); user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.156” used
US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: Section D-D (cut along the notch's centre line, View C-C: the left wall at the rear); user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Photo 0.145 in ± 0.015 in
Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Read by rows 298 to 330: the slot's rear wall's shadow ends at u 970.3 and the notch shows through from u 990.5 (its front wall's near edge): 20.2 px, 0.147 in the mid-plane's scale, 0.9% less for the wall's face, 0.319 nearer the lens. (The same rows have a lit band from u 982 to 990.5, 0.158 high: the shallow step View C-C draws at the notch's front, not drawn here.)
The drawing's callout; BCM's photo reads 0.011 less, a pixel and a half.
Where the latch's hook drops into the wall. Taken as: Section D-D is the left wall cut along the notch's centre line, its .195 the slot along the receiver and its .156 the wall behind the slot, to the notch's front end. Checked on the reference model (the slot's flat from x 0.233, which is .156 ahead of 0.077) and on BCM's own left photo.
The latch's slot, along the receiver (its ends full rounds of half this)0.195 in ± 0.005 in 5 mmConfirmedStandard: US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: Section D-D (cut along the notch's centre line, View C-C: the left wall at the rear); user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.195” used
US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: Section D-D (cut along the notch's centre line, View C-C: the left wall at the rear); user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
View C-C marks the slot's end FULL R.
Model 0.192 in ± 0.003 in
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text in the rifle frame its lug holes set: two rounds about z, r 0.0960, at (x 0.329, y 1.616) and (x 0.329, y 1.839), from the wall's face at z -0.318 in to the slot's floor at -0.251; the flat between them from x 0.233 to 0.425
Photo 0.2 in ± 0.012 in
Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Read by rows 298 to 330: its front rim's bright line rises at u 942.5 and its rear wall's shadow ends at u 970.3: 27.8 px, 0.202, 0.9% less for the wall's face; the rim's line is two pixels wide
The drawing's callout; the reference model's rounds make it 0.192 and BCM's photo reads 0.200: all three within their ±.
The latch's slot, the wall left under it: between its floor and the charging handle's channel0.045 in ± 0.005 in 1.1 mmConfirmedStandard: US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: Section D-D (cut along the notch's centre line, View C-C: the left wall at the rear); user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.045” used
US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: Section D-D (cut along the notch's centre line, View C-C: the left wall at the rear); user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Taken as the strip of wall under the slot's floor: the two lines it is drawn between are the floor's and the wall's inner face.
Model 0.043 in ± 0.004 in
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text in the rifle frame its lug holes set: the slot's floor is a plane at z -0.251 from x 0.233 to 0.425, y 1.520 to 1.940, and the channel's wall beside it at z -0.208 (from the rear face to x 0.510)
The drawing's callout; the reference model's is 0.002 less.
The slot is a pocket in the wall's outer face, not a window into the channel. Section D-D has .045 of wall under it; the reference model has its floor a plane over the slot's whole outline; and BCM's left photo has it lit inside (35 to 50 of 255 on rows 298 to 330, for the wall's 30), its rear wall's shadow across it, where a window into the channel would be the darkest thing on that side.
The latch's slot, its lower end above the pin line1.527 in ± 0.012 in 38.8 mmCorroboratedPhoto: Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768
Photo 1.527 in ± 0.012 in used
Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Read by columns 950 to 964: the slot's lower edge at v 341.5 (its rim bright at 340 to 341 toward the front, its shadow ending at 339 to 341 toward the rear), 208.0 px above the pin line there: 1.510, through the lens 1.527 (profiles.left, latch_slot)
Model 1.52 in ± 0.003 in
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by as latch_slot_length: the lower round's centre at y 1.616, less its r 0.0960
BCM's own part; the reference model's is 0.007 lower, a pixel.
Its heights have no callout in View C-C or Section D-D: BCM's own photo, with the reference model beside it.
The latch's slot, its upper end above the pin line1.926 in ± 0.012 in 48.9 mmCorroboratedPhoto: Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768
Photo 1.926 in ± 0.012 in used
Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Read by columns 950 and 957: the lit foot of the rail above the slot ends at v 286 to 287, 263.5 px above the pin line there: 1.913, through the lens 1.926 (profiles.left, latch_slot)
Model 1.935 in ± 0.003 in
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by as latch_slot_length: the upper round's centre at y 1.839, plus its r 0.0960
BCM's own part; the reference model's is 0.009 higher, a pixel.
The rail's slots, floor below the top (the reference model's)0.115 in ± 0.003 in 2.9 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging
Model 0.115 in ± 0.003 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text: slot walls from y 1.975 to 2.090
MIL-STD-1913's .118 +.008 (std.picatinny.slot_depth) is what the app's rail is drawn to.
The rail's dovetail, its foot (where the neck begins), Y above the pin line1.885 in ± 0.003 in 47.9 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging
Model 1.885 in ± 0.003 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text in the rifle frame its lug holes set (x = 15.0189 - mx, y = my + 6.2992, z = -(mz + 0.8128), inches; a working script, run again 2026-10-05), cut at x 1.8: the 45° face from (0.333, 1.885) to (0.418, 1.969)
The rail's dovetail at its foot, half its width0.323 in ± 0.013 in 8.2 mmProvisionalWorked out: {std.picatinny.bevel_width} / 2 + {std.picatinny.lower_gauge_below_top} - ({.rail_top_above_pin} - {.dovetail_foot_y})
Model 0.333 in ± 0.003 in
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by as dovetail_foot_y: the 45° face's lower end, z 0.333
Worked out 0.323 in ± 0.013 in used
{std.picatinny.bevel_width} / 2 + {std.picatinny.lower_gauge_below_top} - ({.rail_top_above_pin} - {.dovetail_foot_y}), harvested
The standard's lower face carried on at its 45 degrees from the lower gauge line (.748 across, .154 below the rail's top) to the height the reference model has the foot at: the face every other rail on file has (the teeth the app draws on this body, a handguard's own rail) and every clamp's channel is cut to. ± is the gauge line's .010 and the model's .003.
The standard's, since 2026-10-12: a rail's head is MIL-STD-1913's, and the clamps' channels are cut to it (pipeline/blender/lib.py rail_seat). The reference model draws the same face a hundredth further out, at the standard's stated .164 where the ledger has the middle of .164 -.020 (std.picatinny.lower_gauge_below_top): inside the standard's band, and on a body drawn so every clamp stood 0.008 in into the rail along both sides (0.001 cubic inches of an Aimpoint's base). The model isn't authoritative beside the standard; its neck and the foot's height are still its own.
The rail's neck below its dovetail, half its width0.309 in ± 0.003 in 7.8 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging
Model 0.309 in ± 0.003 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by as dovetail_foot_y: planar faces z ±0.309 from y 1.700 to 1.885
The rail's neck, where it meets the receiver's sides, Y1.7 in ± 0.003 in 43.2 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging
Model 1.7 in ± 0.003 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by as dovetail_foot_y: the step out from ±0.309 to ±0.319 at y 1.700
The receiver's flat sides below the rail's neck, half its width0.319 in ± 0.003 in 8.1 mmCorroboratedModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging
Model 0.319 in ± 0.003 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by as dovetail_foot_y: planar faces z ±0.319 from y 1.440 to 1.700, then a .10 fillet to the round body
Photo 0.32 in ± 0.02 in
BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400, harvested
Scale: the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top. Read by the teeth's top flats between their chamfers, 78 px across (0.643): the rail's flat top is as wide as the walls under it in the model (z ±0.318)
The top flat's width, the same ±0.318 in the reference model: a check that BCM's rail has the model's section, not a reading of the wall itself.
The model's face; BCM's rail from above has the model's top flat.
The receiver's flat sides, where they turn into the round body, Y1.44 in ± 0.005 in 36.6 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging
Model 1.44 in ± 0.005 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by as dovetail_foot_y: the flat sides' lower end at y 1.440
The walls below the round body down to the underside, half the width0.453 in ± 0.003 in 11.5 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging
Model 0.453 in ± 0.003 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by as dovetail_foot_y: planar faces z ±0.453 from y 0.250 to 0.458 (inside ±0.251)
The gas tube's hole through the front wall0.183 in ± 0.0015 in 4.7 mmConfirmedStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-3/3, front view; user-supplied scan (Distribution Statement F), PDF page 126
Standard “.182 +.003 ∅ THRU; .781 ± .005” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-3/3, front view; user-supplied scan (Distribution Statement F), PDF page 126, from the site owner
The gas tube's hole above the bore's axis0.781 in ± 0.005 in 19.8 mmConfirmedStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-3/3, front view; user-supplied scan (Distribution Statement F), PDF page 126
Standard “.781 ± .005” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-3/3, front view; user-supplied scan (Distribution Statement F), PDF page 126, from the site owner
The gas tube's hole, its four lobes' radius0.047 in ± 0.005 in 1.2 mmConfirmedStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-3/3, front view; user-supplied scan (Distribution Statement F), PDF page 126
Standard “.042 +.010 R 4 PLACES EQL SP RANDOM ORIENTATION EXCEPT MUST NOT INTERSECT THREADS” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-3/3, front view; user-supplied scan (Distribution Statement F), PDF page 126, from the site owner
BCM's photo of the front end shows the four lobes under its BCM4 mark, set on the diagonals.
The four lobes' centres from the hole's centre0.11 in ± 0.005 in 2.8 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging
Model 0.11 in ± 0.005 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text in the rifle frame its lug holes set: four cylinders r .045 about (y 1.585 and 1.740, z ±0.078) round the hole's own at (y 1.662, z 0): 0.110 off its centre, on the diagonals
The barrel-nut thread's major diameter (1 1/4-18 UNEF-2A, after anodize)1.244 in ± 0.0045 in 31.6 mmConfirmedStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-1/3, Detail C; user-supplied scan (Distribution Statement F), PDF page 123
Standard “1.250 -18 UNEF-2A: MAJOR ∅ 1.2485 – 1.2398 AFTER COATING” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-1/3, Detail C; user-supplied scan (Distribution Statement F), PDF page 123, from the site owner
The side photo's thread reads 1.19 to 1.21 crest to crest: thin crests on white are eaten by the background's bloom, so it isn't a check.
The barrel-nut thread's minor diameter1.18 in ± 0.003 in 30 mmConfirmedStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-1/3, Detail C; user-supplied scan (Distribution Statement F), PDF page 123
Standard “MINOR ∅ 1.1803 MAX AFTER COATING” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-1/3, Detail C; user-supplied scan (Distribution Statement F), PDF page 123, from the site owner
A maximum: the roots are drawn at it.
The barrel-nut thread's pitch (18 to the inch)0.056 in ± 0.0001 in 1.4 mmConfirmedStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-1/3, Detail C; user-supplied scan (Distribution Statement F), PDF page 123
Standard “1.250 -18 UNEF-2A” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-1/3, Detail C; user-supplied scan (Distribution Statement F), PDF page 123, from the site owner
1/18 in.
The barrel's index pin's notch in the thread, width0.127 in ± 0.001 in 3.2 mmConfirmedStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view; user-supplied scan (Distribution Statement F), PDF page 124
Standard “.126 +.002” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view; user-supplied scan (Distribution Statement F), PDF page 124, from the site owner
The index pin's notch, how far back from the front face0.16 in ± 0.01 in 4.1 mmConfirmedStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view; user-supplied scan (Distribution Statement F), PDF page 124
Standard “.15 +.02” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view; user-supplied scan (Distribution Statement F), PDF page 124, from the site owner
The ejection port's front end at the outer surface (the front hinge lug's rear face), X6.078 in ± 0.015 in 154.4 mmConfirmedWorked out: {.front_face_x} - 1.00in + 0.042in
Worked out 6.078 in ± 0.015 in used
{.front_face_x} - 1.00in + 0.042in, from the site owner
US Army TDP drawing 12576280, frame F-2/3, side elevation (PDF page 124): "1.01 −.02" and ".037 +.010".
Model 6.079 in ± 0.003 in
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text in the rifle frame its lug holes set: the hinge lugs' bores (r .0625 about y 0.641, z 0.689) end at x 2.932 and 6.079
Photo 6.11 in ± 0.03 in
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens about 38 in away over x 2.2. Read by the closed cover's front edge reads 6.176 and its rear edge 3.000 (0.6 nearer the lens: x 1.0167): 6.111 and 2.987, 3.124 apart (the cover is 3.130 by its drawing)
The drawing; the reference model has the same face within 0.001 and BCM's closed cover ends 0.03 ahead, within the photo's ±.
The M16A2's drawing takes 1.01 −.02 from the front face to the opening's inner front end, and ends the 3.120 +.010 slot .037 +.010 ahead of that. (The M16A1's has the same "1.00" and ".042": the catalog's other forged upper reads the port's end at the 1.00, 0.04 behind this.)
The ejection port's length at the outer surface (between the hinge lugs)3.125 in ± 0.005 in 79.4 mmConfirmedStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, side elevation; user-supplied scan (Distribution Statement F), PDF page 124
Standard “3.120 +.010; 1.562 ± .010” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, side elevation; user-supplied scan (Distribution Statement F), PDF page 124, from the site owner
The M16A1's 8448524 has it as 3.125.
The port's lower edge above the pin line, seen from the side0.841 in ± 0.01 in 21.4 mmConfirmedStandard: US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G, side view, scaled (not a callout): its lower straight edge at px row 3640 against the lug holes' row 3900 at the sheet's own 309.3 px/in (the lug holes 6.375 apart); R .25 TRUE ends; a copy on file
Standard 0.841 in ± 0.01 in used
US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G, side view, scaled (not a callout): its lower straight edge at px row 3640 against the lug holes' row 3900 at the sheet's own 309.3 px/in (the lug holes 6.375 apart); R .25 TRUE ends; a copy on file, from the site owner
As the catalog's other forged upper has it (its own photo, port open, read 0.834).
The port's ends' radius (half its height from the side)0.25 in ± 0.005 in 6.3 mmConfirmedStandard: US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation; user-supplied scan, a copy on file
Standard “.25 R TRUE 2 PLACES” used
US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation; user-supplied scan, a copy on file, from the site owner
The M16A2's View F-F: (.24 R).
The port's face (the cover's seat), turned up from the side22.5° ± 1°ConfirmedStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-3/3, Detail G; user-supplied scan (Distribution Statement F), PDF page 126
Standard “22° 30' ± 1° 0'” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-3/3, Detail G; user-supplied scan (Distribution Statement F), PDF page 126, from the site owner
The port cover's hinge pin, Y above the pin line0.641 in ± 0.005 in 16.3 mmCorroboratedModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging
Model 0.641 in ± 0.005 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text in the rifle frame its lug holes set: the hinge lugs' bores r .0625 about (y 0.641, z 0.689)
Photo 0.63 in ± 0.03 in
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens 4 to 5 in above the pin line, 35.5 to 38 in away. Read by the pin's end ahead of the front hinge lug, centred at px row 457.5: reads 0.542, 0.69 nearer the lens; through it 0.61 to 0.64
The model places the pin; BCM's reads the same through the photo's lens. (The M16A2's Detail G, read as .545 −.010 off the bore along the port's face's normal and .495 +.010 down it, gives 0.62.)
The port cover's hinge pin, out from the middle (Z)0.689 in ± 0.005 in 17.5 mmCorroboratedModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging
Model 0.689 in ± 0.005 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by as hinge_y
Photo 0.66 in ± 0.03 in
BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400, harvested
Scale: the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top; lower things read smaller about a point 1.5 in to the receiver's left (the body's two edges). Read by the closed cover's outermost edge along the port, px row 141: 0.75 from the middle at the hinge's height, less the hinge's curl (.090: 8448785)
The model places the pin; BCM's from above reads 0.03 less, within its ±.
The port cover's length3.13 in ± 0.005 in 79.5 mmConfirmedStandard: US Army TDP drawing 8448785 (Cover, Ejection Port), rev C (its application block lists the M4); user-supplied scan, PDF page 136
Standard “3.130 -A-” used
US Army TDP drawing 8448785 (Cover, Ejection Port), rev C (its application block lists the M4); user-supplied scan, PDF page 136, from the site owner
Photo 3.124 in ± 0.03 in
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; 0.6 nearer the lens, 38 in away. Read by the closed cover's two ends 406 px apart (3.175), less the 1.67% its plane reads long
The drawing; BCM's cover reads the same within 0.006.
The port cover's height, its hinge's axis to its free edge0.79 in ± 0.005 in 20.1 mmConfirmedStandard: US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136
Standard “.790” used
US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136, from the site owner
The port cover's sheet0.025 in ± 0.0015 in 0.6 mmConfirmedStandard: US Army TDP drawing 8448785 (Cover, Ejection Port), rev C, Section C-C; user-supplied scan, PDF page 136
Standard “.0250 ± .0015 STOCK THICKNESS” used
US Army TDP drawing 8448785 (Cover, Ejection Port), rev C, Section C-C; user-supplied scan, PDF page 136, from the site owner
The port cover's two beads, how far they stand off the sheet0.05 in ± 0.005 in 1.3 mmConfirmedStandard: US Army TDP drawing 8448785 (Cover, Ejection Port), rev C, Section C-C; user-supplied scan, PDF page 136
Standard “.05, BOTH BEADS” used
US Army TDP drawing 8448785 (Cover, Ejection Port), rev C, Section C-C; user-supplied scan, PDF page 136, from the site owner
The port cover's two free corners0.25 in ± 0.005 in 6.3 mmConfirmedStandard: US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136
Standard “.250 R, 2 PLACES” used
US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136, from the site owner
The port cover's hinge curl, inside0.13 in ± 0.003 in 3.3 mmConfirmedStandard: US Army TDP drawing 8448785 (Cover, Ejection Port), rev C, Section C-C; user-supplied scan, PDF page 136
Standard “.130 DIA -B-” used
US Army TDP drawing 8448785 (Cover, Ejection Port), rev C, Section C-C; user-supplied scan, PDF page 136, from the site owner
The port cover's sheet between its hinge knuckles' ends (its beads are set out from it)3.1 in ± 0.005 in 78.7 mmConfirmedStandard: US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136
Standard “3.100” used
US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136, from the site owner
Each bead's two legs, centre to centre1.115 in ± 0.005 in 28.3 mmConfirmedStandard: US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136
Standard “1.115 2 PLACES” used
US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136, from the site owner
The two beads' inner legs, centre to centre (the latch housing between them)0.62 in ± 0.005 in 15.7 mmConfirmedStandard: US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136
Standard “.620” used
US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136, from the site owner
The beads' inset: their tops below the cover's free edge, their legs' ends above the hinge's line0.12 in ± 0.01 in 3 mmConfirmedStandard: US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136
Standard “.12, 2 PLACES” used
US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136, from the site owner
Called out twice, once at each end of the legs; read as both insets.
The beads' corners (their centre line)0.125 in ± 0.005 in 3.2 mmConfirmedStandard: US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136
Standard “.125 R, 4 PLACES” used
US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136, from the site owner
The beads' section, the radius inside the pressed sheet0.025 in ± 0.005 in 0.6 mmConfirmedStandard: US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136, Section C-C
Standard “.025R, BOTH BEADS” used
US Army TDP drawing 8448785 (Cover, Ejection Port), rev C; user-supplied scan, PDF page 136, Section C-C, from the site owner
The cover's seat on the receiver, below the hinge pin's centre along the port's face's normal0.04 in ± 0.005 in 1 mmConfirmedStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-3/3, Detail G; user-supplied scan (Distribution Statement F), PDF page 126
Standard “.040 ± .005 2 PLACES” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-3/3, Detail G; user-supplied scan (Distribution Statement F), PDF page 126, from the site owner
Read as from the hinge holes' centre to the cutter's surface the cover lies on.
The two hinge lugs' radius about the pin0.137 in ± 0.003 in 3.5 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging
Model 0.1365 in ± 0.003 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text in the rifle frame its lug holes set: cylinders r .1365 about (y 0.641, z 0.689) over x 2.837 to 2.932 and 6.079 to 6.235
The rear hinge lug's rear end, X2.806 in ± 0.005 in 71.3 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging
Model 2.806 in ± 0.005 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by as hinge_lug_r: the pin's bore (r .0625) runs from x 2.806 to 2.932
The front hinge lug's front end, X6.235 in ± 0.005 in 158.4 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging
Model 6.235 in ± 0.005 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by as hinge_lug_r: the pin's bore runs from x 6.079 to 6.235
The hinge pin's front end, X6.6 in ± 0.04 in 167.6 mmProvisionalPhoto: Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768
Photo 6.6 in ± 0.04 in used
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; 0.69 nearer the lens, 38 in away over x 2.2. Read by the pin's end ahead of the front hinge lug at px 1021 (6.68), through the lens
The hinge pin's rear end, X2.83 in ± 0.04 in 71.9 mmProvisionalPhoto: Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768
Photo 2.83 in ± 0.04 in used
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; 0.69 nearer the lens, 38 in away over x 2.2. Read by the pin's head behind the rear hinge lug at px 530 (2.836), through the lens
The port cover's latch housing, along the cover0.45 in ± 0.03 in 11.4 mmProvisionalPhoto: Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768
Photo 0.45 in ± 0.03 in used
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; 0.55 nearer the lens, 38 in away. Read by the square boss at the cover's middle, px 725 to 783 (0.454), less the 1.5% its plane reads long; it is as tall as wide (px rows 368 to 425)
The cover's drawing leaves .433 +.004 between its beads for it.
The latch housing, how far it stands off the coverNo value yetMissingNo source yet
No view on file gives it a size: the housing's own drawing (8448784) wasn't read. Drawn at the beads' height until it is.
The forward assist's axis, turned inward toward the front in plan20° ± 1°ConfirmedStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view; user-supplied scan (Distribution Statement F), PDF page 124
Standard “20° ± 1°” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view; user-supplied scan (Distribution Statement F), PDF page 124, from the site owner
Photo 20.1 deg ± 1 deg
BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400, harvested
Scale: the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top. Read by the housing's outer edge over px 820 to 1020, 9 px in every 25 (19.8° on the photo; 20.1° with lower things read through the lens); its cap's rim stands 20.6° off square
The drawing; BCM's part from above reads the same.
The forward assist's bore, its mouth's centre out from the middle (Z)1.028 in ± 0.005 in 26.1 mmConflictStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view; user-supplied scan (Distribution Statement F), PDF page 124
Standard “1.0285 ± .0050” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view; user-supplied scan (Distribution Statement F), PDF page 124, from the site owner
Read as the line the 20° is struck from: the bore's centre where it leaves the housing's rear face.
Photo 1.045 in ± 0.03 in
BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400, harvested
Scale: the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top; 118.2 px/in at the bore's height (the cap's .605 rim: 71.5 px). Read by where the cap's stem leaves the housing's rear face, px (1053, 102 to 106): 1.03 to 1.06
Model 1.09 in ± 0.005 in
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text: the bore's axis through (-0.395, 0.879, 1.090), turned 22.5°
The drawing's callout, which BCM's part from above agrees with; the reference model stands 0.06 further out (and is turned 22.5°, not 20).
tdp and model differ by 0.062 in beyond what each states it is good to.
banner and model differ by 0.045 in beyond what each states it is good to.
The forward assist's bore, its mouth's centre, X-0.44 in ± 0.04 in -11.2 mmCorroboratedPhoto: BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400
Photo -0.44 in ± 0.04 in used
BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400, harvested
Scale: the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top, the rearmost slot's centre at px 842.0 as rail_slot0_x; lower things read 2.5% smaller about a point near the receiver's rear end (its rear face reads where the drawing has it only with the lens there). Read by where the cap's stem leaves the housing's rear face, px 1054: 0.432 behind the takedown pin at the rail's scale, -0.438 through the lens; the ± is the lens's place along the receiver
Standard -0.43 in ± 0.04 in
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view, scaled (not a callout): the bore's centre line crosses the 1.0285 line 0.19 ahead of the rear face at the sheet's 245 px/in; user-supplied scan, PDF page 124, from the site owner
BCM's own part; the drawing, scaled, agrees within 0.01.
The forward assist's bore0.509 in ± 0.003 in 12.9 mmConfirmedStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view; user-supplied scan (Distribution Statement F), PDF page 124
Standard “.506 +.006 ∅ TO DEPTH SHOWN” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view; user-supplied scan (Distribution Statement F), PDF page 124, from the site owner
The M16A1's 8448524: .509 DIA ± .003.
The forward assist's bore, its depth from the mouth0.65 in ± 0.01 in 16.5 mmConfirmedStandard: US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view; user-supplied scan (Distribution Statement F), PDF page 124
Standard “.65 ± .01” used
US Army TDP drawing 12576280 (Receiver, Upper: the M16A2's), frame F-2/3, plan view; user-supplied scan (Distribution Statement F), PDF page 124, from the site owner
Read as the full bore's depth along its axis from the housing's rear face.
The forward assist housing's radius about its axis0.305 in ± 0.02 in 7.7 mmCorroboratedPhoto: BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400
Photo 0.305 in ± 0.02 in used
BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400, harvested
Scale: the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top; 118.2 px/in at the bore's height. Read by the housing's outer edge (a straight line over 200 px, 20° off the receiver's) stands 1.370 from the middle at the mouth: 0.32 square off the axis by the drawing's mouth (1.0285), 0.29 by the photo's own (1.06)
Photo 0.285 in ± 0.025 in
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; about 1.1 nearer the lens, 38 in away (the ± is that depth, 0.9 to 1.4). Read by the housing's lit bar from the right, 75 px tall (0.587), less the 3% its depth reads large: 0.57 across
Model 0.3125 in ± 0.003 in
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text (the 2026-10-03 research pass): the housing's cylinder r .3125 on the bore's axis
BCM's part from above, between the side photo's reading and the reference model's: the three span 0.03.
The forward assist's cap, its head0.605 in ± 0.005 in 15.4 mmConfirmedStandard: US Army TDP drawing 9349084 (Cap, Plunger), rev H (its application block lists the M4 through 9349085); user-supplied scan (Distribution Statement F), PDF page 151
Standard “.610 −.010 ∅” used
US Army TDP drawing 9349084 (Cap, Plunger), rev H (its application block lists the M4 through 9349085); user-supplied scan (Distribution Statement F), PDF page 151, from the site owner
The forward assist's cap, its body0.486 in ± 0.004 in 12.3 mmConfirmedStandard: US Army TDP drawing 9349084 (Cap, Plunger), rev H; user-supplied scan (Distribution Statement F), PDF page 151
Standard “.490 −.008 ∅ -A-” used
US Army TDP drawing 9349084 (Cap, Plunger), rev H; user-supplied scan (Distribution Statement F), PDF page 151, from the site owner
The forward assist's cap, end to end0.71 in ± 0.005 in 18 mmConfirmedStandard: US Army TDP drawing 9349084 (Cap, Plunger), rev H; user-supplied scan (Distribution Statement F), PDF page 151
Standard “.715 −.010” used
US Army TDP drawing 9349084 (Cap, Plunger), rev H; user-supplied scan (Distribution Statement F), PDF page 151, from the site owner
The forward assist's cap, its straight body (the rest is the head's 20° flare)0.57 in ± 0.005 in 14.5 mmConfirmedStandard: US Army TDP drawing 9349084 (Cap, Plunger), rev H, Section A-A; user-supplied scan (Distribution Statement F), PDF page 151
Standard “.565 +.010; 20° ± 1°” used
US Army TDP drawing 9349084 (Cap, Plunger), rev H, Section A-A; user-supplied scan (Distribution Statement F), PDF page 151, from the site owner
The forward assist's cap at rest, its rear face behind the housing's (along the axis)0.5 in ± 0.05 in 12.7 mmCorroboratedPhoto: BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400
Photo 0.5 in ± 0.05 in used
BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400, harvested
Scale: the cap's own rim, .605 across (9349084): 71.5 px, 118.2 px/in. Read by from where the stem leaves the housing (px 1054, 102) to the middle of the rim's thickness (px 1104.5, 85.5): 53 px, 0.449, and half the rim's 0.11
Photo 0.47 in ± 0.06 in
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; 1.2 to 1.5 nearer the lens, 38 in away. Read by the cap's rearmost point reads -1.145 (its rim's near edge, 0.10 behind its face's centre for the 20° turn) against the housing's rear rim at -0.527: through the lens -1.03 and -0.44, 0.59 apart along x, less the rim's 0.10, over cos 20°
The view that sees the cap along its own axis; the side photo agrees within its ±.
The deflector's rear face at the body, X2.06 in ± 0.02 in 52.3 mmCorroboratedModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging
Photo 2.075 in ± 0.04 in
BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400, harvested
Scale: the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top, the rearmost slot's centre at px 842.0 as rail_slot0_x; lower things read 2% smaller about a point near the receiver's rear end. Read by the rear face's foot at px 755
Photo 2.04 in ± 0.03 in
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens over x 2.2 (so nothing to correct here). Read by the rear face's fold against the body, px 428
Model 2.06 in ± 0.02 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text (the 2026-10-03 research pass): the deflector's faces over x 2.06 to 2.99, y 0.95 to 1.70, reaching z 1.20 to 1.30
Between BCM's two photos, which read 0.035 apart, and within each one's ±.
The deflector's front face, where it runs out into the body, X2.97 in ± 0.04 in 75.4 mmCorroboratedPhoto: BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400
Photo 2.97 in ± 0.04 in used
BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400, harvested
Scale: the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top, the rearmost slot's centre at px 842.0 as rail_slot0_x; lower things read 2% smaller about a point near the receiver's rear end. Read by the front face's foot at px 648
Photo 2.97 in ± 0.03 in
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens over x 2.2, 38 in away. Read by its lit face ends beside the cover's rear edge, px 548 (2.977), 0.6 nearer the lens
Both of BCM's photos give the same figure (the reference model: 2.99).
The deflector's outer ridge, X2.4 in ± 0.04 in 61 mmCorroboratedPhoto: BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400
Photo 2.4 in ± 0.04 in used
BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400, harvested
Scale: the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top, the rearmost slot's centre at px 842.0 as rail_slot0_x; lower things read 2% smaller about a point near the receiver's rear end. Read by the rounded tip at px 712 to 722
Photo 2.44 in ± 0.04 in
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens over x 2.2, 38 in away. Read by the bright edge between its two faces, px 478 to 485 (2.453), 1.26 nearer the lens
The view that sees the ridge's reach; the side photo reads 0.04 more, within their ±.
The deflector's reach out from the middle (Z)1.26 in ± 0.03 in 32 mmCorroboratedPhoto: BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400
Photo 1.26 in ± 0.03 in used
BCM's shop, the upper receivers category's banner: an M4 flat top with T-marks, forward assist and port door from straight above, 1200 x 400, harvested
Scale: the rail's 13 slots at std.picatinny.slot_pitch: 121.27 px/in at the rail's top; lower things read smaller about a point 1.5 in to the receiver's left (the body's two edges, which that makes 0.60 either side). Read by the tip at px row 77: 1.24 to 1.28 from the middle as its height is taken from 1.5 down to 0.9
Model 1.25 in ± 0.05 in
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text (the 2026-10-03 research pass): the deflector's faces reach z 1.20 to 1.30
BCM's own part; the reference model agrees.
The deflector's top at the body, Y above the pin line1.7 in ± 0.02 in 43.2 mmCorroboratedModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging
Photo 1.72 in ± 0.04 in
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens 4 to 5 in above the pin line, about 38 in away. Read by its top edge at px row 315 reads 1.657, 0.6 to 0.9 nearer the lens: 0.06 more through it
Model 1.7 in ± 0.02 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by its faces read from the STEP text (the 2026-10-03 research pass): the deflector's faces over y 0.95 to 1.70
The model's figure, which BCM's photo gives within its ± once read through its lens.
The deflector's foot at the body, Y above the pin line0.95 in ± 0.02 in 24.1 mmCorroboratedModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging
Photo 1 in ± 0.04 in
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens 4 to 5 in above the pin line, about 38 in away. Read by its lower edge at px row 408 reads 0.929, 0.65 nearer the lens: 0.07 more through it
Model 0.95 in ± 0.02 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec forging, from the site owner
Read by as deflector_top_y
As deflector_top_y: the photo agrees within its ±.
The deflector's outer ridge, its top, Y above the pin line1.67 in ± 0.05 in 42.4 mmProvisionalPhoto: Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768
Photo 1.67 in ± 0.05 in used
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens 4 to 5 in above the pin line, about 38 in away. Read by the bright edge between its faces runs from px row 328 to 400 (1.555 down to 0.992), 1.26 nearer the lens: 0.12 more through it
The deflector's outer ridge, its foot, Y above the pin line1.11 in ± 0.05 in 28.2 mmProvisionalPhoto: Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768
Photo 1.11 in ± 0.05 in used
Primary Arms, BCM4-UR-M4_01: the assembled upper's right side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins: 127.86 px/in in the mid-plane; the lens 4 to 5 in above the pin line, about 38 in away. Read by as deflector_ridge_top_y: the edge's lower end
The raised band low on the left wall, its front end, X6.105 in ± 0.02 in 155.1 mmProvisionalPhoto: Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768
Photo 6.105 in ± 0.02 in used
Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane, the takedown hole at (997.82, 549.45) px; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Checked beside it: the underside under the band reads at row 522.3 for the 521.7 the lens puts the deck's 0.2485 at on a face 0.527 out. Read by rows 476, 482 and 490: the tone falls from 38, 41 and 35 at column 150 to 23, 26 and 25 at column 155 and stays (the band's own tone, 23 to 35): 152.5 px, 6.138 in the mid-plane, 6.105 through the lens on a face 0.527 out. It begins at the pivot lug's rear edge, with no lit line: its front end is in shadow
An upright flat along the foot of the left wall, from the deck up to an edge on the round body, darker than the body over it and than the wall behind it. Raised, not sunk, on three counts: its rear end shows as a lit face leaning rearward, from a line at column 590 to a foot that is under it at row 476 and 11 px behind it from row 498 down, which is the round body falling away behind a flat face down to the lug wall's crease and the wall's flat below; its underside reads a pixel lower in the picture than the wall's behind it (row 522.3 against 521.0), as a face 0.07 in nearer a lens 3.3 in above does (0.9 px); and the cam pin's pad over it, which the reference model has raised, is lit at the same end. How far it stands out is in no view: the script takes its face to stand where the body as drawn is at its upper edge's height (0.527 off the middle, 0.074 out from the lug wall), and its rear end then leans 43 degrees.
The raised band low on the left wall, its face's rear edge, X2.975 in ± 0.015 in 75.6 mmProvisionalPhoto: Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768
Photo 2.975 in ± 0.015 in used
Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane, the takedown hole at (997.82, 549.45) px; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Checked beside it: the underside under the band reads at row 522.3 for the 521.7 the lens puts the deck's 0.2485 at on a face 0.527 out. Read by rows 476 to 520: a lit line a pixel or two wide at column 590 (82, 97, 95, 95, 97, 99, 97, 100, 102, 104 at rows 476 to 520, against 33 to 46 at column 585 on the band): 590 px, 2.961 in the mid-plane, 2.975 through the lens on a face 0.527 out
The raised band low on the left wall, the foot of its rear end on the wall behind it, X2.895 in ± 0.015 in 73.5 mmProvisionalPhoto: Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768
Photo 2.895 in ± 0.015 in used
Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane, the takedown hole at (997.82, 549.45) px; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Checked beside it: the underside under the band reads at row 522.3 for the 521.7 the lens puts the deck's 0.2485 at on a face 0.527 out. Read by rows 498 to 520: a second lit line at columns 600 to 602 (92, 96, 98, 104, 111, 110 at column 600, 55 to 58 at 605, 45 to 61 between the two lines at 595); above row 498 it closes on the first and meets it at row 476, where the band's upper edge is: 601 px, 2.882 in the mid-plane, 2.895 through the lens on the lug wall, 0.453 out
The raised band low on the left wall, its upper edge above the pin line0.601 in ± 0.015 in 15.3 mmProvisionalPhoto: Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768
Photo 0.601 in ± 0.015 in used
Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane, the takedown hole at (997.82, 549.45) px; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Checked beside it: the underside under the band reads at row 522.3 for the 521.7 the lens puts the deck's 0.2485 at on a face 0.527 out. Read by columns 158, 170, 250, 330, 420, 500 and 560: the body's tone over it (41 to 45 at row 470) falls to the band's (23 to 35 by row 476), at half its fall at rows 472.0, 472.9, 472.0, 472.2, 472.3, 471.5 and 472.2: 472.3 px, 0.560 above the pin line in the mid-plane, 0.601 through the lens on a face 0.527 out. Level end to end within a pixel
Behind the band the round body meets the lug wall's flat at rows 496 to 498 (columns 625, 700, 800): 0.42 above the pin line through the lens, for the 0.49 the section as drawn has that crease at (the round of body_radius about the bore meeting lug_wall_half_width). The body's section below the bore is the reference model's and isn't read on BCM's part; it is left as it is.
The tab on the raised band, its front end, X4.57 in ± 0.03 in 116.1 mmProvisionalPhoto: Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768
Photo 4.57 in ± 0.03 in used
Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane, the takedown hole at (997.82, 549.45) px; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Checked beside it: the underside under the band reads at row 522.3 for the 521.7 the lens puts the deck's 0.2485 at on a face 0.527 out. Read by rows 506, 510 and 518: the band's 34 to 39 rises to the tab's 40 to 45 between columns 365 and 375 (row 518's lit lower edge begins at 365: 39, 64): 367 px ± 4, 4.581 in the mid-plane, 4.570 through the lens. A soft beginning: drawn square
A low lump on the band's foot, under the cam pin's pad: lighter than the band (40 to 47 for its 32 to 36), its upper face lit and leaning, a lit line along its lower edge at row 518, and a lit end leaning rearward as the band's own is. Its underside reads a pixel lower than the band's (row 524 is 231 to 241 under it and 248 to 252 elsewhere), as a face nearer the lens does. How far it stands off the band is in no view: the script takes its rear end to lean as the band's own rear end does as drawn, which puts its face 0.059 off the band's, inside the body's widest.
The tab on the raised band, its face's rear edge, X3.962 in ± 0.015 in 100.6 mmProvisionalPhoto: Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768
Photo 3.962 in ± 0.015 in used
Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane, the takedown hole at (997.82, 549.45) px; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Checked beside it: the underside under the band reads at row 522.3 for the 521.7 the lens puts the deck's 0.2485 at on a face 0.527 out. Read by rows 513 to 522: the lit end begins at column 452 (row 516: 43 at 450, 120 at 455; row 518: 59, 128; row 520: 70, 120): 452 px, 3.964 in the mid-plane, 3.962 through the lens (it stands almost under the lens, 3.9)
The tab on the raised band, the foot of its rear end on the band, X3.898 in ± 0.015 in 99 mmProvisionalPhoto: Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768
Photo 3.898 in ± 0.015 in used
Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane, the takedown hole at (997.82, 549.45) px; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Checked beside it: the underside under the band reads at row 522.3 for the 521.7 the lens puts the deck's 0.2485 at on a face 0.527 out. Read by rows 518 to 522: the lit end reaches column 461 at its foot (row 518: 81 at 460, 51 at 465; row 520: 113 at 460, 48 at 465) and narrows upward to nothing at row 513, column 455: 461 px, 3.898 in the mid-plane and through the lens alike. A face square to the receiver would not show from a lens over x 3.9: it leans
The tab on the raised band, where its upper face leaves the band, above the pin line0.368 in ± 0.015 in 9.3 mmProvisionalPhoto: Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768
Photo 0.368 in ± 0.015 in used
Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane, the takedown hole at (997.82, 549.45) px; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Checked beside it: the underside under the band reads at row 522.3 for the 521.7 the lens puts the deck's 0.2485 at on a face 0.527 out. Read by columns 380, 400, 420 and 440: the band's 34 to 36 begins to rise at rows 504 to 506 (36, 40, 42 at column 380; 35, 37, 40 at 400): 505 px, 0.323 above the pin line in the mid-plane, 0.368 through the lens on a face 0.527 out
The tab on the raised band, its outer face's upper edge above the pin line0.316 in ± 0.015 in 8 mmProvisionalPhoto: Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768
Photo 0.316 in ± 0.015 in used
Primary Arms, BCM4-UR-M4_03: the assembled upper's left side, 1152 x 768, harvested
Scale: its two lug holes' see-through lenses as the pins, std.ar15.pin_spacing apart: 137.71 px/in in the mid-plane, the takedown hole at (997.82, 549.45) px; the lens 35 in away, 3.3 in above the pin line over x 3.9 (left_photo_lens_*). Checked beside it: the underside under the band reads at row 522.3 for the 521.7 the lens puts the deck's 0.2485 at on a face 0.527 out. Read by columns 380, 400, 420 and 440: the lit upper face is brightest at row 512 (47, 48, 48, 44) and the face under it is 40 to 42 from row 514: 513 px, 0.265 above the pin line in the mid-plane, 0.316 through the lens on a face 0.586 out
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
AR-15 receiver pins
- Lower receivers
- Aero Precision M4E1 complete lower, A2 grip and M4 stock, Aero Precision M4E1 Stripped Lower Receiver, Battle Arms Development Workhorse stripped lower, BCM MK2 AR-15 Lower Receiver, Bear Creek Arsenal BC-15 Multi Caliber, Lower Receiver, Black Anodized, Geissele Automatics Super Duty AR-15 Lower Receiver - Stripped Lower, Palmetto State Armory AR-15 "Stealth" Stripped Lower Receiver
Barrel extension
- Barrels
- Aero Precision 16" 5.56 CMV barrel, mid-length, BCM Standard 11.5" Carbine Barrel, Stripped, BCM Standard 14.5" Mid Length Barrel, Stripped, BCM Standard 16" Mid Length Barrel, Stripped, Bear Creek Arsenal BC-15 5.56 NATO, 16" Parkerized M4 Barrel, 1:7 Twist, Mid-Length Gas System, Daniel Defense CHF Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 10.3", Faxon Firearms Duty Series Pencil Profile 16" Mid-Length 5.56 NATO AR15 Barrel, Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 13.9", Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 14.5", Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 16", Rosco Manufacturing Bloodline 10.5" M4 5.56 NATO, Rosco Manufacturing Bloodline 11.5" M4 5.56 NATO, Rosco Manufacturing Bloodline 12.5" M4 5.56 NATO
Handguard mount
- Handguards
- Aero Precision AR15 10.3" R-ONE M-LOK handguard, Aero Precision AR15 12.7" R-ONE M-LOK handguard, Aero Precision AR15 15" Enhanced M-LOK Handguard, Gen 2, Aero Precision AR15 15" R-ONE M-LOK handguard, Aero Precision AR15 15" S-ONE M-LOK Handguard, Aero Precision AR15 16.6" R-ONE M-LOK handguard, Aero Precision AR15 7.3" R-ONE M-LOK handguard, Aero Precision AR15 9.3" R-ONE M-LOK handguard, BCM MCMR-10 (M-LOK® Compatible* Modular Rail), BCM MCMR-13 (M-LOK® Compatible* Modular Rail), BCM MCMR-15 (M-LOK® Compatible* Modular Rail), BCM PMCR (Polymer M-LOK® Compatible Rail)* Carbine Length-BLACK, BCM PMCR (Polymer M-LOK® Compatible Rail)* Mid Length-BLACK, Expo Arms Free Float AR-15 Handguard - M-LOK - 15", Geissele Automatics 10.5" Super Modular Rail MK16 M-LOK, Geissele Automatics 13.5" Super Modular Rail MK16 M-LOK, Geissele Automatics 15" Super Modular Rail MK16 M-LOK, Magpul MOE SL® Hand Guard, Carbine-Length – AR15/M4, Magpul MOE SL® Hand Guard, Mid-Length – AR15/M4, Magpul MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4, Magpul MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4, MAS Defense 12.62" NERO M-LOK FREE FLOAT, MAS Defense 15" NERO M-LOK FREE FLOAT, MAS Defense 9.87" NERO M-LOK FREE FLOAT, Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length), Midwest Industries Combat Rail One Piece Free Float Handguard, M-LOK™ (15")
- Barrel nuts
- BCM G.I. Barrel Nut - AR15, Spike's Tactical Delta Ring Assembly w/Mil-Spec Barrel Nut
Bolt carrier channel
Charging handle channel
- Charging handles
- Aero Precision AR15/M4 5.56 charging handle, BCM Ambidextrous MK2 Charging Handle - Large Latch (5.56mm/.223), Radian Weapons AR-15 / M16 Raptor-LT Ambidextrous Charging Handle, Radian Weapons Raptor Ambidextrous Charging Handle AR15/M16, Radian Weapons Raptor-SD Ambidextrous Charging Handle AR15/M16
Picatinny rail (MIL-STD-1913)
- Red dot mounts
- Aimpoint Duty RDS One-piece TNP Mount, 30 mm, Aimpoint LRP (Lever Release Picatinny) Mount with 39 mm Spacer, for Micro, Aimpoint One-piece Torsion Nut Mount and Spacer, 39 mm, Geissele Super Precision T1 Mount - 1.93" Height, Geissele Super Precision T1 Mount - Absolute Co-Witness, Geissele Super Precision T1 Mount - Lower 1/3 Co-Witness, Holosun 1.63 in lower 1/3 co-witness pedestal mount (HS-MOUNT-AR-RISER-ARO), Midwest Industries MK2 QD T2 Aimpoint Mount, Low, Midwest Industries MK2 QD T2 Aimpoint Mount, Lower 1/3 Cowitness, Midwest Industries MK2 QD T2 Aimpoint Mount, NV 2.26 in Height, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – 1.93″ HEIGHT, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – LOWER 1/3 (39MM HEIGHT), Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.42 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.57 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.93 in, Scalarworks LEAP/02 Aimpoint Micro T-2 quick-detach mount, 2.26 in, SIG Sauer M1913 I-BEAM Mount, 1.41 in absolute co-witness, SIG Sauer See-Through Riser Mount, 1.41 in absolute co-witness, Unity Tactical FAST Micro Mount, 2.26 in optical centerline
- Optics
- Aimpoint Patrol Rifle Optic (PRO) Red Dot Reflex Sight - QRP2 Mount, EOTECH HWS EXPS3 holographic weapon sight, 1-Dot Speed Ring, Holosun HS510C Open Reflex MRS Solar QD Mount
- Lights
- Olight Baldr S BL, Streamlight ProTac Rail Mount HL-X, SureFire Mini Scout Light Pro, SureFire Scout Light Pro Dual Fuel
- Backup sights
- Daniel Defense A1.5 Fixed Rear Sight, Daniel Defense Rail Mounted Fixed Front Sight, Magpul MBUS 3 Sight – Front, Magpul MBUS 3 Sight – Rear, Magpul MBUS Pro Sight – Front, Magpul MBUS Pro Sight – Rear
- Magnifiers
- EOTECH G33 Magnifier, STS Mount, EOTECH G45 Magnifier, STS Mount, Holosun HM3X 3× magnifier with flip mount
- Scope mounts
- Primary Arms Deluxe AR-15 Scope Mount - 30mm, Primary Arms SLx Cantilever 30mm Mount - 1.5", Reptilia AUS™ MOUNT - 30MM DIAMETER - 39MM HEIGHT, Scalarworks LEAP/08 quick-detach scope mount, 30 mm, 1.57 in, SIG SAUER ALPHA-MSR scope mount, 30 mm, Vortex Sport Cantilever 30mm Mount
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- BCM $129.00 Nov 21, 2026, out of stock that day
- Primary Arms $129.00 Nov 21, 2026, out of stock that day
- AR15Discounts $129.00 Nov 21, 2026, out of stock that day
- Rifle Supply $131.99 Nov 21, 2026, out of stock that day
- Alexander's Store $143.99 Nov 18, 2026, out of stock that day
- Aerospace Arms $144.95 Nov 21, 2026, out of stock that day
- Right To Bear $149.00 Nov 21, 2026, out of stock that day