Scope mount
Vortex Sport Cantilever 30mm Mount
Vortex's one-piece cantilever scope mount for a 30 mm tube, the rings' axis 1.50 in above the rail ("Center Scope Height 1.50""), "Lightweight, under 5.5 oz." in "6061 Aluminum". The rings are "Horizontally split for easier mounting"; two clamp blocks, each on two screws, hold it to a Picatinny rail, and two recoil lugs under it lie in the rail's slots. Vortex: "The 2" offset gets your head position and eye relief dialed, while leaving plenty of real estate on your rail."

- Weight
- 5.39 oz Confirmedpublished: Vortex Optics, Sport Cantilever 30mm Mount (SCM-30-150): Specifications, the maker, read Oct 13, 2026
- Lowest price
- $119.99 at Primary Arms, read Nov 21, 2026 (Matte black)
- Maker's number
- SCM-30-150
- Colour
- Black (placeholder)
- Drawn as
- modelled
- Maker's page
- vortexoptics.com
In “22RB carbine, scoped”, a build on the start page, in place of its SIG SAUER ALPHA-MSR scope mount, 30 mm.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Ring axis above the rail's top1.5 in ± 0.005 in 38.1 mmConfirmedPublished: Vortex Optics, Sport Cantilever 30mm Mount (SCM-30-150): Specifications, the maker, read Oct 13, 2026
Published “Center Scope Height 1.50"” used
Vortex Optics, Sport Cantilever 30mm Mount (SCM-30-150): Specifications, the maker, read Oct 13, 2026 the page, harvested Oct 13, 2026
Published “Center Scope Height: 1.50" (38.1mm)”
Scheels, Vortex Sport Cantilever 30mm Mount (875874-SCM-30-150), a seller, read Oct 13, 2026 the page, harvested Oct 13, 2026
Published “1.5in Optical Centerline”
Sportsman's Warehouse, Vortex Optics Sport 30mm Cantilever Mount Matte Black - 1 Piece (Model SCM-30-150), a seller, read Oct 13, 2026 the page, harvested Oct 13, 2026
Photo 1.475 in ± 0.025 in
Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123, harvested
Scale: the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture). Read by the 30 mm tube's centre line (its two edges' middle, row 326.8 over the base) above the rail's top: 90.6 px
The maker's figure, engraved on the mount; two sellers repeat it. The picture's reading is 0.025 under it, at the edge of what a pixel and the picture's scale allow.
Vortex's own word for it is "Center Scope Height"; Scheels gives the same in millimetres and Sportsman's calls it the optical centerline. The mount's rear end is engraved "30MM 1.50"" (picture `bl`). The side view of it on a rifle reads 1.475 at the rail's scale: 1.7% under, with the 30 mm tube in it reading 1.9% thin in the same picture (71.2 px for 72.6); kept beside the maker's figure, which the model is built on.
Tube diameter the rings are bored for1.181 in 30 mmConfirmedPublished: Vortex Optics, Sport Cantilever 30mm Mount (SCM-30-150): Specifications, the maker, read Oct 13, 2026
Published “Tube Size 30mm” used
Vortex Optics, Sport Cantilever 30mm Mount (SCM-30-150): Specifications, the maker, read Oct 13, 2026 the page, harvested Oct 13, 2026
Published “Tube Size: 30 mm”
Scheels, Vortex Sport Cantilever 30mm Mount (875874-SCM-30-150), a seller, read Oct 13, 2026 the page, harvested Oct 13, 2026
Published “30mm Ring Size”
Sportsman's Warehouse, Vortex Optics Sport 30mm Cantilever Mount Matte Black - 1 Piece (Model SCM-30-150), a seller, read Oct 13, 2026 the page, harvested Oct 13, 2026
The maker's figure; the mount's rear end is engraved "30MM 1.50"".
The maker's "2\" Offset" (what it spans isn't said)2 in 50.8 mmConfirmedPublished: Vortex Optics, Sport Cantilever 30mm Mount (SCM-30-150): Specifications, the maker, read Oct 13, 2026
Published “2" Offset” used
Vortex Optics, Sport Cantilever 30mm Mount (SCM-30-150): Specifications, the maker, read Oct 13, 2026 the page, harvested Oct 13, 2026
Published and undefined: Vortex's only sentence is "The 2" offset gets your head position and eye relief dialed, while leaving plenty of real estate on your rail."; Sportsman's Warehouse: "With a 2in offset, this mount positions your scope forward". Nothing is built on it. Tried on the side view (2026-10-13), no span of the mount comes to 2 in within its ±: the front ring's middle is 1.80 in ahead of the front jaw's front end (the end of the clamp), and that ring's front face 2.20 ahead of it; the middle between the two rings is 1.67 ahead of the clamp's middle. The figure reads as a round one for how far the front ring stands ahead of the clamp.
Rear ring, its middle ahead of the rear recoil lug0.186 in ± 0.03 in 4.7 mmProvisionalPhoto: Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123
Photo 0.186 in ± 0.03 in used
Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123, harvested
Scale: the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture). Read by the ring's cap where it stands over the tube, its two ends at columns 825.4 and 869.3 (the top silhouette's steps, at the level midway between the tube's top and the cap's): their middle, 847.35, less the rear lug's 835.95
The mount has no cross bolt: its two recoil lugs lie in two neighbouring slots, and the part frame's origin is on the rail's top over the rear one's middle (column 835.95: the lug's own middle and the slot's, 0.05 px apart).
Front ring, its middle ahead of the rear recoil lug3.611 in ± 0.07 in 91.7 mmProvisionalPhoto: Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123
Photo 3.611 in ± 0.07 in used
Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123, harvested
Scale: the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture). Read by the ring's cap over the tube, columns 1034.4 to 1081.2: their middle, 1057.8, less the rear lug's 835.95. This ring reads 2.9 px longer than the rear one (its front end is a soft edge, 3 px wide, where the rear one's ends are sharp): its middle is good to 1.5 px
The picture's scale is the rail's, good to 0.1% along the rail. What it leaves open: the scope and the mount in it read 1.7 to 1.9% small up and down by that scale (optical_axis_above_rail), which a black part's edges on white explain only in part, so the mount may be drawn a little smaller than the rifle in this picture; at that other scale (60.3 px/in) this figure would be 3.68 and the rings 3.49 apart. Two things say the rail's scale is the mount's: its lugs lie in the rail's slots a pitch apart, and the camera fitted to picture `fr`, whose scale is the 30 mm bore, puts the base's rear end 1.528 in behind the rear ring's middle, where this picture has 1.526 at the rail's scale and 1.555 at the other. The cameras themselves leave the rings' spacing open (3.58 and 3.41 in when it is left to them, each ± 0.02 formally): they agree with 3.425 and can't better it. The ± here covers the other scale.
Each ring's length along the tube (face to face)0.735 in ± 0.015 in 18.7 mmCorroboratedPhoto: a photo on file
Photo 0.735 in ± 0.015 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by the distance between each bore's two rims, a free parameter of each camera's fit: 0.730 and 0.739. It moves with the spacing given to the fit, 0.021 for each tenth of an inch
Photo 0.738 in ± 0.03 in
Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123, harvested
Scale: the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture). Read by each cap over the tube: 43.9 px for the rear ring (0.714) and 46.8 px for the front (0.762): their mean
The bore's own two rims, in two pictures; the side view's two rings read 0.05 apart and their mean agrees.
Clamp length along the rail (at its foot)3.148 in ± 0.04 in 80 mmProvisionalPhoto: Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123
Photo 3.148 in ± 0.04 in used
Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123, harvested
Scale: the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture). Read by from the rear fixed jaw's rear end (the base's rear end, column 753.6) to the front fixed jaw's front end (the lit edge at column 947): 193.4 px
Overall length, the base's rear end to the front ring's front face5.345 in ± 0.07 in 135.8 mmProvisionalPhoto: Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123
Photo 5.345 in ± 0.07 in used
Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123, harvested
Scale: the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture). Read by column 753.6 to the front ring's lower half's front face, 1082: 328.4 px
The base's rear end behind the rear recoil lug1.34 in ± 0.03 in 34 mmCorroboratedPhoto: Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123
Photo 1.34 in ± 0.03 in used
Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123, harvested
Scale: the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture). Read by the base's rear end, column 753.6 on four rows, to the rear lug's middle, 835.95
Photo 1.342 in ± 0.03 in
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `fr`: the rear jaw's rear outer top corner, on the plane of the base's top (base_top_y): 1.528 in behind the rear ring's middle, less ring_rear_x
The square view; the camera fitted to the oblique, scaled by the bore, lands on it.
The front jaw's front end ahead of the rear recoil lug1.807 in ± 0.04 in 45.9 mmProvisionalPhoto: Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123
Photo 1.807 in ± 0.04 in used
Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123, harvested
Scale: the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture). Read by the front fixed jaw's front end, the lit edge at column 947 on rows 402 to 418, less 835.95
Rear fixed jaw (right side), its length along the rail0.763 in ± 0.03 in 19.4 mmProvisionalPhoto: Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123
Photo 0.763 in ± 0.03 in used
Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123, harvested
Scale: the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture). Read by columns 753.6 to 800.5 (its front edge is a lit line at column 800)
Front fixed jaw (right side), its length along the rail0.822 in ± 0.03 in 20.9 mmProvisionalPhoto: Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123
Photo 0.822 in ± 0.03 in used
Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123, harvested
Scale: the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture). Read by the lit edges at columns 896.5 and 947
A recoil lug, along the rail0.192 in ± 0.02 in 4.9 mmProvisionalPhoto: Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123
Photo 0.192 in ± 0.02 in used
Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123, harvested
Scale: the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture). Read by the rear lug, dark between two slivers of daylight in its slot: columns 830.06 to 841.89
Each lies in a slot (0.206 wide): the picture has a sliver of daylight ahead of each and behind the rear one. The camera fitted to picture `fr` reads the two 0.18 long and 0.38 apart, the rear one's middle 0.03 behind the origin.
The two recoil lugs, middle to middle0.394 in 10 mmConfirmedWorked out: {std.picatinny.slot_pitch}
Worked out 0.394 in used
{std.picatinny.slot_pitch}, harvested
They lie in neighbouring slots of the receiver's rail in the maker's picture: one pitch, which the picture reads as 0.39 (the lugs' front edges 23.99 px apart, the slots 24.21).
A recoil lug's end, out from the mount's middle0.27 in ± 0.03 in 6.9 mmProvisionalPhoto: a photo on file
Photo 0.27 in ± 0.03 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `fr`: the four upper outer corners of the two lugs where they leave the base's underside, on the plane of the rail's top: 0.287, 0.246, 0.272, 0.247
Read on the right; the picture from the rear left shows lugs in the same notch on the left, and the two sides are drawn alike, each lug one bar across.
The base between the clamp blocks (the wall the maker's mark is on), out from the mount's middle0.27 in ± 0.03 in 6.9 mmProvisionalWorked out: {.lug_half_width}
Worked out 0.27 in ± 0.03 in used
{.lug_half_width}, harvested
The lugs' ends read where they leave the base's underside (lug_half_width), so the base there is at least as wide; in `fr` the lugs' end faces stand in line with the wall over them, a little in. Drawn as wide as the lugs, both sides alike, from the rail's top to the base's top (base_top_y), between the two blocks; where the wall rises into the rear ring's stem it is the stem's lean.
The base's top behind the rear ring, above the rail's top0.316 in ± 0.015 in 8 mmCorroboratedPhoto: Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123
Photo 0.316 in ± 0.015 in used
Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123, harvested
Scale: the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture). Read by the silhouette's top edge over columns 754 to 791, row 398.0, above the rail's top at 417.4
Photo 0.31 in ± 0.02 in
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `bl`: the two upper corners of the base's rear end face, on the plane of the base's rear end (clamp_rear_reach): 0.315 and 0.308 above the rail's top as 1.50 below the rings' axis
The square view; the oblique's camera agrees.
The fixed jaws' feet below the rail's top0.233 in ± 0.015 in 5.9 mmProvisionalPhoto: Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123
Photo 0.233 in ± 0.015 in used
Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123, harvested
Scale: the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture). Read by the lit chamfer along both jaws' feet ends at row 431.7; the rail's top is 417.4
The front fixed jaw's top, above the rail's top0.259 in ± 0.02 in 6.6 mmProvisionalPhoto: Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123
Photo 0.259 in ± 0.02 in used
Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123, harvested
Scale: the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture). Read by the dark line over columns 899 to 941 at row 401.5
The front jaw's block stands out of the base's side under the arm: a dark line along its top at this height in the side view, with the arm's side above it.
A ring's top flat above the rings' axis0.689 in ± 0.012 in 17.5 mmCorroboratedPhoto: Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123
Photo 0.689 in ± 0.012 in used
Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123, harvested
Scale: the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture). Read by the rear ring's cap's top edge, row 284.55, above the tube's centre line there (the middle of its two edges, row 326.85): 42.3 px; the front ring's the same within 0.3 px
Photo 0.677 in ± 0.02 in
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `fr`, the rear ring's front face: its top edge stands 21.4 px over the bore's top on the line up the middle of the face, where the camera has 1500 px/in at the crop's scale of five: 0.071 in, and the flat is a bevel of some 0.015 above the face's edge. (The camera's own height for that edge is 0.64: its bore's top is 6 px above the picture's there, a bias the fit's rims leave up and down.)
A square view of the cap against the centre line of the tube it holds; the oblique's reading rests on a pick of the bevel and agrees within a hundredth.
Counted in the side view from the tube's own upper edge instead (the cap stands 6.85 px over it) it would be 0.702; but the black tube's edges read 0.7 px in on each side there (71.2 px across for 72.6), and from the tube's centre line the two pictures through their cameras agree with it: the ledger's figures drawn back over both (check-a1e2-crop.png, check-2256-crop.png) have each end face's top edge, a bevel under the flat, 0.03 under a top drawn at 0.70.
Rings, across their side flats1.85 in ± 0.015 in 47 mmProvisionalPhoto: a photo on file
Photo 1.85 in ± 0.015 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by the split line where it runs along the near side flat, which lies in the plane of the rings' axis: 0.926 and 0.929 in from the mount's middle (picture `fr`, front and rear ring), 0.924 and 0.920 (picture `bl`); twice their mean. It doesn't move with the rings' spacing (0.001 over a tenth of an inch)
Wider than tall: the cap screws stand beside the tube. The end faces' own edges read 0.90 out (a bevel of 0.02 round each face).
Rings, their top flat across0.76 in ± 0.04 in 19.3 mmProvisionalPhoto: a photo on file
Photo 0.76 in ± 0.04 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `fr`: the two ends of each ring's front face's top edge, on that face's plane: 0.415 and -0.374 (rear ring), 0.384 and -0.348 (front ring) from the middle
Rings, the side flat's height above the split (the cap's)0.15 in ± 0.02 in 3.8 mmProvisionalPhoto: a photo on file
Photo 0.15 in ± 0.02 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `fr`: where each ring's front face's edge turns from the side flat to the upper chamfer, on that face's plane: 0.160 and 0.158 (rear ring, far and near side), 0.156 and 0.126 (front ring)
Rings, the side flat's height below the split (the lower half's)0.115 in ± 0.02 in 2.9 mmProvisionalPhoto: a photo on file
Photo 0.115 in ± 0.02 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `fr`: where each front face's edge turns from the side flat to the lower chamfer: 0.117 and 0.098 (rear ring), 0.137 and 0.106 (front ring)
Rings, where the lower chamfers meet the stem, below the rings' axis0.745 in ± 0.04 in 18.9 mmProvisionalPhoto: a photo on file
Photo 0.745 in ± 0.04 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `fr`: the foot of each lower chamfer on the ring's front face: 0.721 and 0.754 (rear ring), 0.793 and 0.712 (front ring)
Each ring's foot, where its two lower chamfers end, across0.81 in ± 0.05 in 20.6 mmProvisionalPhoto: a photo on file
Photo 0.81 in ± 0.05 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `fr`: the feet of the two lower chamfers on each ring's front face: 0.435 and -0.374 from the middle (rear ring), 0.377 and -0.429 (front ring): 0.809 and 0.806 across
The arm between the rings, across its walls (below its top's chamfers)0.322 in ± 0.045 in 8.2 mmProvisionalWorked out: ({.arm_top_right_z} + {.arm_chamfer_right}) - ({.arm_top_left_z} - {.arm_chamfer_left})
Photo 0.42 in ± 0.08 in
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by both pictures, each against a grid of points on the plane of the arm's top (0.391 above the rail, as the side view has it) drawn through its camera, at 1.4 and 1.8 in ahead of the rear lug: the top flat's right edge is 0.235 out in `fr` and 0.25 in `bl`; its left edge 0.02 left of the middle in `bl` (in `fr` the left chamfer hides it); the lit chamfer under that edge ends on the left wall, which the same grid has between 0.08 and 0.19 left of the middle, by how far the chamfer drops (0.08 to 0.03); the right wall is a narrow chamfer outside the flat's edge, about 0.27. From 0.35 to 0.46 across
Read by eye against a grid. Its right wall, 0.27, is where the narrow chamfer's foot falls on the plane of the top in `fr` (the ray from 15 degrees up crosses that plane 0.05 further out than the foot is): the lit band ends at 0.265 to 0.27 on that plane at every station, and down the chamfer itself it ends 0.025 out from the flat's edge. Its 0.25 in `bl` is where the arm's silhouette meets the white ground, which the tones put at 0.18 to 0.20 (arm_top_right_z).
Worked out 0.322 in ± 0.045 in used
({.arm_top_right_z} + {.arm_chamfer_right}) - ({.arm_top_left_z} - {.arm_chamfer_left}), harvested
The flat's two edges and the two chamfers, each read on the pictures' tones along lines across the arm through the cameras (2026-10-19).
Each edge read where the picture's tone changes along a line cast across the arm through its camera, at three stations, rather than against a grid by eye; the first reading's right wall was the chamfer's foot as it falls on the plane of the top, 0.05 further out than the foot. Kept beside it.
Much narrower than the rings' feet: the stems lean in to it. Its top is a flat with a chamfer down each side, the left one the broader, and the arm is not about the mount's middle: its walls are 0.11 in left and 0.22 right of it (arm_top_left_z, arm_top_right_z and the two chamfers, read again on 2026-10-19 through the same two cameras). The right-hand ends of the two recoil lugs read 0.27 out (lug_half_width): the base under the arm is wider than the arm there, which the maker's mark is on.
The arm's top flat, its left edge from the mount's middle (negative: to the left)-0.032 in ± 0.02 in -0.8 mmProvisionalPhoto: a photo on file
Photo -0.032 in ± 0.02 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `bl`, through its camera: the tone along a line across the arm on the plane of its top (0.395 above the rail) at 1.3, 1.6 and 1.9 in ahead of the rear lug steps from the left chamfer's (32 to 53 of 255) to the flat's (59 to 68) at -0.035, -0.035 and -0.025
The arm's top flat, its right edge from the mount's middle0.19 in ± 0.02 in 4.8 mmProvisionalPhoto: a photo on file
Photo 0.19 in ± 0.02 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `bl`, through its camera: on the plane of the arm's top the flat's tone (64 to 79) meets the white ground beyond the arm half-way at 0.20 (1.6 in ahead of the rear lug) and 0.183 (1.9 in): from the rear left and 18 degrees up, the right chamfer faces away and the silhouette is the flat's edge
The arm's left chamfer, its width across (from the flat's edge out to the left wall)0.075 in ± 0.015 in 1.9 mmProvisionalPhoto: a photo on file
Photo 0.075 in ± 0.015 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `bl`, through its camera: down a 45 degree plane from the flat's left edge (-0.035) the chamfer's tone (37 to 52) holds to 0.07 out and drops to 21 at 0.08, at 1.3, 1.6 and 1.9 in ahead of the rear lug alike
Read as a 45 degree chamfer: its drop is taken to be its width (an assumption for the drawing: one picture sees the left side from above, and its camera gives a line of widths and drops, not one). Drawn so.
The arm's right chamfer, its width across (from the flat's edge out to the right wall)0.025 in ± 0.01 in 0.6 mmProvisionalPhoto: a photo on file
Photo 0.025 in ± 0.01 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `fr`, through its camera: down a 45 degree plane from the flat's right edge (0.195) the lit tone (58 to 79) holds to 0.02 out and drops to 21 to 24 at 0.03, at 1.3, 1.6 and 1.9 in ahead of the rear lug alike. On the plane of the top the lit band ends at 0.265 to 0.27, where a ray from 15 degrees up through a foot 0.025 down and 0.025 out falls
Read as a 45 degree chamfer, as the left one (assumed). The narrow one: the left is three times as broad.
The fixed jaws' outer face, out from the mount's middle (right side)0.637 in ± 0.015 in 16.2 mmProvisionalPhoto: a photo on file
Photo 0.637 in ± 0.015 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `fr`: the rear jaw's two upper outer corners and the front jaw's rear one, on the planes of their tops: 0.640, 0.625, 0.642; picture `bl`: the right-hand corners of the base's rear end face, on its plane: 0.637 and 0.643
The base's left side, where the clamp blocks bear, out from the mount's middle0.43 in ± 0.03 in 10.9 mmProvisionalPhoto: a photo on file
Photo 0.43 in ± 0.03 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `bl`: the upper left corner of the base's rear end face, on its plane: 0.429; the rear clamp's top face's inner front corner on the plane of its top reads 0.451
A hundredth outside the rail's own widest (0.4175): the two clamp blocks stand against it.
The clamp blocks' outer face, out from the mount's middle (left side)0.625 in ± 0.03 in 15.9 mmProvisionalPhoto: a photo on file
Photo 0.625 in ± 0.03 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `bl`: the front corners of both blocks' outer faces, each on the plane of the x the side view has that end of its jaw at: 0.627, 0.627, 0.610, 0.631
A clamp block, its length along the rail0.73 in ± 0.04 in 18.5 mmProvisionalPhoto: a photo on file
Photo 0.73 in ± 0.04 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `bl`: each block's outer face's two upper corners on the plane of that face (clamp_outer_z): the rear block from 1.296 to 0.573 behind the rear lug (0.723), the front one from 1.051 to 1.791 ahead of it (0.740)
The rear clamp block's front end, behind the rear recoil lug0.573 in ± 0.03 in 14.6 mmProvisionalPhoto: a photo on file
Photo 0.573 in ± 0.03 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `bl`: its outer face's upper front corner on the plane of that face; the right side's rear jaw ends 0.577 behind the lug in the side view
The front clamp block's front end, ahead of the rear recoil lug1.791 in ± 0.03 in 45.5 mmProvisionalPhoto: a photo on file
Photo 1.791 in ± 0.03 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `bl`: its outer face's upper front corner on the plane of that face; the right side's front jaw ends 1.807 ahead of the lug in the side view
The clamp blocks' top, above the rail's top0.305 in ± 0.02 in 7.7 mmProvisionalPhoto: a photo on file
Photo 0.305 in ± 0.02 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `bl`: the four upper corners of the two blocks' outer faces on the plane of those faces: 0.293, 0.315, 0.305, 0.320
The clamp blocks' outer face, its lower edge below the rail's top0.065 in ± 0.02 in 1.7 mmProvisionalPhoto: a photo on file
Photo 0.065 in ± 0.02 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `bl`: the lower front corners of the two blocks' outer faces and the front block's rear one, on the plane of those faces: 0.074, 0.068, 0.053
Under it the block is rounded in toward its hook, whose foot is taken to be as low as the fixed jaws' (jaw_bottom_below_rail_top): the hook itself shows only at the rear block's end.
The four base screws, above the rail's top0.135 in ± 0.02 in 3.4 mmProvisionalPhoto: a photo on file
Photo 0.135 in ± 0.02 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `bl`: the rear block's two counterbores' middles on the plane of its outer face: 0.144 and 0.126
They run across the mount above the rail, from the clamp blocks into the base: no screw crosses the rail.
A clamp block's two screws, apart0.325 in ± 0.03 in 8.3 mmProvisionalPhoto: a photo on file
Photo 0.325 in ± 0.03 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `bl`: the rear block's two counterbores' middles on the plane of its outer face: 0.755 and 1.080 behind the rear lug
A screw's counterbore, across0.23 in ± 0.03 in 5.8 mmProvisionalPhoto: a photo on file
Photo 0.23 in ± 0.03 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `bl`: the rear block's two counterbores, 62 and 64 px tall where the camera has 271 px/in up and down
The same screw holds the ring caps and the clamps (Vortex: "Commonality between fasteners and components for one-tool mounting"; Torx T-25 for both).
A screw's head, across0.21 in ± 0.03 in 5.3 mmProvisionalPhoto: a photo on file
Photo 0.21 in ± 0.03 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `bl`: the heads in the rear block's counterbores, about 50 px tall at 271 px/in (0.185); picture `fr`: a head in the front ring's cap, 58 px along the ring where the ring's 0.735 in is 188 px (0.23): their mean
The ring caps' screws, out from the mount's middle0.762 in ± 0.025 in 19.4 mmProvisionalPhoto: a photo on file
Photo 0.762 in ± 0.025 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `fr`: the two heads on the near side of each ring, taken to be level and even about the ring's middle and solved through the camera for how far out, how high and how far apart: 0.758 (rear ring, 6.5 px left over) and 0.767 (front ring, 2.0 px)
Midway between the bore's wall (0.591) and the side flat (0.925), where they have to be.
A ring cap's two screws on one side, apart0.39 in ± 0.03 in 9.9 mmCorroboratedPhoto: a photo on file
Photo 0.39 in ± 0.03 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `fr`, with cap_screw_z: 0.391 (rear ring) and 0.387 (front ring)
Photo 0.387 in ± 0.02 in
Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123, harvested
Scale: the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture). Read by the two small dark windows in the rear ring's lower half, under its two screws, at columns 835.9 and 859.7
Read on the screws' own heads; the side view's two windows under them are the same distance apart.
The ring caps' screws, their heads' tops above the rings' axis0.255 in ± 0.03 in 6.5 mmProvisionalPhoto: a photo on file
Photo 0.255 in ± 0.03 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `fr`, with cap_screw_z: 0.260 (rear ring) and 0.250 (front ring)
A ring cap's screw pocket, across0.32 in ± 0.04 in 8.1 mmProvisionalPhoto: a photo on file
Photo 0.32 in ± 0.04 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `fr`, the front ring's near side: the rear pocket is 86 px along the ring where the ring's own 0.735 in (its side flat's edge) is 188 px
Each pocket is a round cut straight down into the cap's chamfer beside the tube, open to the side flat: two a side, a thin wall between them.
Rings, the bevel between an end face and a side flat0.022 in ± 0.012 in 0.6 mmProvisionalPhoto: a photo on file
Photo 0.022 in ± 0.012 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by picture `fr`: the six places where the rear ring's front face's edge meets its side flats read 0.884 to 0.917 from the middle (mean 0.9035) on that face's plane, where the side flats are 0.925 out (ring_width)
Rings, the gap between a cap and its lower half0.014 in ± 0.006 in 0.4 mmProvisionalPhoto: a photo on file
Photo 0.014 in ± 0.006 in used
a photo on file, harvested
Scale: each ring's 30 mm bore (ring_bore) and the rings' spacing (ring_front_x - ring_rear_x), through a pinhole camera fitted to each picture. Read by pictures `fr` and `bl`: the dark line between each cap and its lower half is 4 to 5 px across where the cameras have 310 to 320 px/in up the rings' faces
The fixed jaws, the chamfer along their feet0.065 in ± 0.02 in 1.7 mmProvisionalPhoto: Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123
Photo 0.065 in ± 0.02 in used
Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123, harvested
Scale: the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture). Read by a lit band along both jaws' feet, rows 427.7 to 431.7
The window under each cap screw in a ring's lower half, across0.065 in ± 0.02 in 1.7 mmProvisionalPhoto: Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123
Photo 0.065 in ± 0.02 in used
Vortex, vtx_rac_sportcantilevermount_30mm_mp_w.jpg: the mount on an AR-15 with a scope in it, the rifle's right side square on, 1920 x 1123, harvested
Scale: the receiver's rail slots (std.picatinny.slot_pitch), by the daylight through seven of them behind and under the mount, their centres at columns 666.52, 690.76, 714.94, 739.29, 811.72, 884.32 and 957.00 (slots -7 to -4, -1, 2 and 5 from the rear lug's): 24.207 px a slot, 61.44 px/in, no centre more than 0.15 px off the line; the rail's top is the teeth's top edge, row 417.4 under the mount (tilted 0.25 degrees with the picture). Read by each of the rear ring's two windows is a dark dot about 4 px across
Where each screw's threaded hole breaks out of the lower chamfer: a small dark opening that shows the thread. The camera fitted to picture `fr` has the front ring's two on the chamfer 0.34 and 0.37 below the rings' axis, 0.70 to 0.76 out; the side view has the rear ring's 0.39 below it. Drawn as the hole itself, this wide, straight down from the screw's seat: it breaks out of the chamfer 0.27 to 0.35 below the axis.
The groove at each ring's split: how deep0.02 in ± 0.01 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows it in profile.
Worked out 0.02 in ± 0.01 in used
An assumption for the drawing, not a reading: no view on file shows it in profile., harvested
A screw's six-pointed socket: how deep0.02 in ± 0.01 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows it in profile.
Worked out 0.02 in ± 0.01 in used
An assumption for the drawing, not a reading: no view on file shows it in profile., harvested
A base screw's head under its clamp block's outer face0.01 in ± 0.01 in 0.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows it in profile.
Worked out 0.01 in ± 0.01 in used
An assumption for the drawing, not a reading: no view on file shows it in profile., harvested
The break on the mount's machined edges0.006 in ± 0.004 in 0.2 mmProvisionalWorked out: An assumption for the drawing, not a reading: the pictures show every edge broken and none at a size a pixel can give; the figure is the one the other mounts on file are drawn with.
Worked out 0.006 in ± 0.004 in used
An assumption for the drawing, not a reading: the pictures show every edge broken and none at a size a pixel can give; the figure is the one the other mounts on file are drawn with., harvested
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Picatinny rail (MIL-STD-1913)
- Uppers
- Aero Precision M4E1 Enhanced Upper Receiver Stripped, Aero Precision M4E1 Threaded upper receiver, BCM M4 Upper Receiver Assembly (w/ Laser T-Markings), Expo Arms 7075 Stripped AR-15 Upper Receiver, Geissele Automatics Super Duty Stripped Upper Receiver, Nordic Components 22RB .22 LR upper, 16", Palmetto State Armory AR-15 Stripped Upper Receiver, Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12", Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16"
- Handguards
- Aero Precision AR15 10.3" R-ONE M-LOK handguard, Aero Precision AR15 12.7" R-ONE M-LOK handguard, Aero Precision AR15 15" Enhanced M-LOK Handguard, Gen 2, Aero Precision AR15 15" R-ONE M-LOK handguard, Aero Precision AR15 15" S-ONE M-LOK Handguard, Aero Precision AR15 16.6" R-ONE M-LOK handguard, Aero Precision AR15 7.3" R-ONE M-LOK handguard, Aero Precision AR15 9.3" R-ONE M-LOK handguard, BCM MCMR-10 (M-LOK® Compatible* Modular Rail), BCM MCMR-13 (M-LOK® Compatible* Modular Rail), BCM MCMR-15 (M-LOK® Compatible* Modular Rail), Expo Arms Free Float AR-15 Handguard - M-LOK - 15", Geissele Automatics 10.5" Super Modular Rail MK16 M-LOK, Geissele Automatics 13.5" Super Modular Rail MK16 M-LOK, Geissele Automatics 15" Super Modular Rail MK16 M-LOK, MAS Defense 12.62" NERO M-LOK FREE FLOAT, MAS Defense 15" NERO M-LOK FREE FLOAT, MAS Defense 9.87" NERO M-LOK FREE FLOAT, Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length), Midwest Industries Combat Rail One Piece Free Float Handguard, M-LOK™ (15")
- Frames
- Taurus TX22 Gen 2 frame
- Rail sections
- Magpul M-LOK® Aluminum Rail, 3 Slots, Magpul M-LOK® Aluminum Rail, 5 Slots, Magpul M-LOK® Aluminum Rail, 7 Slots, Magpul M-LOK® Aluminum Rail, 9 Slots, Magpul M-LOK® Polymer Rail, 11 Slots, Magpul M-LOK® Polymer Rail, 3 Slots, Magpul M-LOK® Polymer Rail, 5 Slots, Magpul M-LOK® Polymer Rail, 7 Slots, Magpul M-LOK® Polymer Rail, 9 Slots
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Primary Arms $119.99 Matte black Nov 21, 2026, in stock that day
- KYGUNCO $119.99 Matte black Nov 21, 2026, in stock that day
- Sportsman's Warehouse $119.99 Matte black Nov 21, 2026, in stock that day
- AR15Discounts $119.99 Matte black Nov 21, 2026, in stock that day
- Scheels $119.99 Matte black Oct 13, 2026, in stock that day