Handguard
Aero Precision AR15 15" R-ONE M-LOK handguard
Aero Precision's 15 in R-ONE free-float M-LOK handguard: 6061-T6, a full top Picatinny rail, QD sockets at 3, 6 and 9 o'clock, mounted by its own barrel nut on a standard upper's thread. "Compatible with mil-spec AR15 upper receivers and barrels"; "NOT Compatible with M4E1 Enhanced Upper Receivers".

- Weight
- 9.07 oz ± 0.01 oz Conflictpublished: Aero Precision, AR15 15" R-ONE M-LOK Handguard - Anodized Black (APRA500705A), Specifications, the maker, read Oct 2, 2026Its sources span 8.96 oz to 9.08 oz.
- Lowest price
- $122.50 at Aero Precision, read Nov 21, 2026 (SOCOM Blue Cerakote)
- Maker's number
- APRA500705A
- Colours
- Anodized Black, OD Green Anodized, Kodiak Brown Anodized, OD Green Cerakote, SOCOM Blue Cerakote, FDE Cerakote, Burnt Bronze Cerakote, Sniper Grey Cerakote
- Drawn as
- modelled
- Maker's page
- aeroprecisionusa.com
In “Aero 5.56 carbine”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Length (the receiver's face to the end of the last rail slot)15 in ± 0.05 in 381 mmConflictPublished: Aero Precision, AR15 15" R-ONE M-LOK Handguard - Anodized Black (APRA500705A), Specifications, the maker, read Oct 2, 2026
Published “Handguard Length 15"” used
Aero Precision, AR15 15" R-ONE M-LOK Handguard - Anodized Black (APRA500705A), Specifications, the maker, read Oct 2, 2026 the page, harvested Oct 2, 2026
Published “Actual Length (When Installed): 15-Inch: 14.94"”
Wing Tactical, Aero Precision ATLAS R-ONE M-LOK Handguard (one page for the 7.3, 9.3, 12.7 and 15 in lengths), Specifications, a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
A seller's table; it doesn't say between what its installed length is taken.
The maker's, with its own rule for what the length spans (the receiver's face to the end of the last rail slot), which the outline is placed by. The seller's 14.94 when installed is 0.06 under it and doesn't say what it spans.
aero and wing-tactical differ by 0.06 in beyond what each states it is good to.
Aero says what its lengths are between: "Aero Precision rail lengths measure from end to end. This is the point of contact at the receiver to the end of the last picatinny slot at the muzzle."
Width across its side faces at their lower edges, where it is widest (the maker's "outside diameter")1.5 in ± 0.05 in 38.1 mmConfirmedPublished: Aero Precision, AR15 15" R-ONE M-LOK Handguard - Anodized Black (APRA500705A), Features, the maker, read Oct 2, 2026
Published “1.5" Outside diameter” used
Aero Precision, AR15 15" R-ONE M-LOK Handguard - Anodized Black (APRA500705A), Features, the maker, read Oct 2, 2026 the page, harvested Oct 2, 2026
Published “Outside Diameter: Height: 1.95" Width: 1.51"”
Wing Tactical, Aero Precision ATLAS R-ONE M-LOK Handguard (one page for the 7.3, 9.3, 12.7 and 15 in lengths), Specifications, a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
A seller's table gives the section's height and width apart: it isn't round. The views from its end have it flat-sided all round, faces at 3, 6 and 9 o'clock among them (2026-10-05: until then the model was a round tube of this diameter).
The maker's own figure, to one place; the seller's 1.51 is inside it.
Height (with the top rail)1.95 in ± 0.005 in 49.5 mmConflictPublished: Wing Tactical, Aero Precision ATLAS R-ONE M-LOK Handguard (one page for the 7.3, 9.3, 12.7 and 15 in lengths), Specifications, a seller, read Oct 5, 2026
Photo 1.981 in ± 0.02 in
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in. Read by the traced outline's height between 4 in and its front end (the body's): 118.4 px
Published “Outside Diameter: Height: 1.95" Width: 1.51"” used
Wing Tactical, Aero Precision ATLAS R-ONE M-LOK Handguard (one page for the 7.3, 9.3, 12.7 and 15 in lengths), Specifications, a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
Photo 1.96 in ± 0.017 in
Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630, harvested
Scale: each view's own top rail, its teeth's period by autocorrelation over 30 of them against the Picatinny pitch (std.picatinny.slot_pitch): 23.60 px a tooth, 59.94 px/in in both; heights from the teeth's tops. Read by the tube's rows, away from the clamp: the teeth's tops at row 245 (244 in the right view), the bottom's last dark row 362 (361): 117.5 rows, a row either way
A seller's table of the maker's sizes, to two places; the side views' rows read 1.96 ± 0.017 at the rail's scale. The traced outline stands 1.98 along its body: inside what a 1000 px photo carries, and kept as read.
photo and wing-tactical differ by 0.031 in beyond what each states it is good to.
The body's, its rail's top to its bottom flat; the clamp's end, with its anti-rotation tab, reaches 2.14. With the rail level with the receiver's (rail_top_above_bore, 1.2125), 1.95 puts the bottom flat 0.7375 below the bore, and half the width is 0.75: the body is centred on the bore, as high below it as it is wide to each side.
Overall length, end to end15.36 in ± 0.03 in 390.1 mmProvisionalPhoto: Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630
Photo 15.36 in ± 0.03 in used
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in. Read by the silhouette end to end, 918 px
Aero's 15 in runs from the receiver to the end of the last rail slot; the handguard goes on past it, and its clamp's end overlaps the receiver's threads.
The rearmost M-LOK slot's centre on its sides, ahead of the handguard's rear end (its outline's x = 0)4.897 in ± 0.02 in 124.4 mmProvisionalPhoto: Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630
Photo 4.897 in ± 0.02 in used
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in. Read by the seven long slots' centres along their row (px 101 to 668, mirrored), fitted to the M-LOK pitch (std.mlok.slot_pitch): they land on it to 0.4%; read from the outline's rear end (it was written as 4.452 ahead of the receiver's face with the rear end taken at -0.445)
The rearmost M-LOK slot's centre on its sides, ahead of the receiver's face4.134 in ± 0.028 in 105 mmProvisionalWorked out: {.rear_x} + {.mlok_slot0_from_rear}
Worked out 4.134 in used
{.rear_x} + {.mlok_slot0_from_rear}, harvested
Seven slots on each side at 3 and 9 o'clock, on the bore's level (the row's centre reads 0.03 above it). The thin slots above and below them, and the short one and the QD socket behind them, aren't M-LOK.
How many M-LOK slots on each side7ProvisionalPhoto: Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630
Photo 7 count used
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in. Read by counted
Its rail's top above the bore axis1.212 in ± 0.02 in 30.8 mmCorroboratedWorked out: {aero-m4e1-threaded-upper.rail_top_above_pin} - {aero-m4e1-threaded-upper.bore_axis_above_pin}
Worked out 1.2125 in ± 0.02 in used
{aero-m4e1-threaded-upper.rail_top_above_pin} - {aero-m4e1-threaded-upper.bore_axis_above_pin}, harvested
Level with the receiver's rail: Aero's page for the M4E1 Threaded upper says its picatinny profile "blends seamlessly with our R-ONE, S-ONE and Enhanced Handguards". So the receiver's rail top above the pin line less the bore's height above it.
Inside width (the maker's "inside diameter")1.3 in ± 0.05 in 33 mmConfirmedPublished: Aero Precision, AR15 15" R-ONE M-LOK Handguard - Anodized Black (APRA500705A), Features, the maker, read Oct 2, 2026
Published “1.3" Inside diameter” used
Aero Precision, AR15 15" R-ONE M-LOK Handguard - Anodized Black (APRA500705A), Features, the maker, read Oct 2, 2026 the page, harvested Oct 2, 2026
Published “Inside Diameter: Height: 1.65" Width: 1.3"”
Wing Tactical, Aero Precision ATLAS R-ONE M-LOK Handguard (one page for the 7.3, 9.3, 12.7 and 15 in lengths), Specifications, a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
The maker's own figure; the seller's table has the same.
Inside height (its floor to the underside of its rail)1.65 in ± 0.005 in 41.9 mmProvisionalPublished: Wing Tactical, Aero Precision ATLAS R-ONE M-LOK Handguard (one page for the 7.3, 9.3, 12.7 and 15 in lengths), Specifications, a seller, read Oct 5, 2026
Published “Inside Diameter: Height: 1.65" Width: 1.3"” used
Wing Tactical, Aero Precision ATLAS R-ONE M-LOK Handguard (one page for the 7.3, 9.3, 12.7 and 15 in lengths), Specifications, a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
0.35 more than its width: the room over the barrel, where the gas block and tube go. With walls of ({.width} - {.inside_diameter}) / 2 its floor is 0.64 below the bore and its top 1.01 above it, 0.2 under the rail's top: up inside the rail's neck, a channel the rail's windows open into. The view from its muzzle end (abbec08229c1) has that channel's top an arch, 0.19 below the rail's top (row 757 where the top is 706.4 and an inch down is 267.8 rows): 1.66 above a floor a wall thick.
Its side faces' upper edge, below the rail's top0.88 in ± 0.02 in 22.4 mmCorroboratedPhoto: Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630
Photo 0.88 in ± 0.02 in used
Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630, harvested
Scale: each view's own top rail, its teeth's period by autocorrelation over 30 of them against the Picatinny pitch (std.picatinny.slot_pitch): 23.60 px a tooth, 59.94 px/in in both; heights from the teeth's tops. Read by the tone down the solid bars between the slots (35 and 32 columns with no opening from 0.8 to 1.05 in down): a step from the slanted face's tone to the flat's, 96 to 59 at 0.868 in the left view and 96 to 58 at 0.891 in the right, a bright line along the edge just above it
0.33 above the bore.
Photo 0.883 in ± 0.015 in
Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it, harvested
Scale: the same end face in the same photo: across, its width at the side faces' lower edges, where it is widest (aero-r-one-15-handguard.width: 427.1 px, 284.8 px/in); down, its rail's top to its bottom flat (aero-r-one-15-handguard.height: rows 706.4 to 1228.6, 267.8 px/in: it is seen from 20 degrees above). One scale down the face serves. Read by each stretch of the end face's outline as a straight line through its own edge crossings, row by row or column by column (rms 0.1 to 0.5 px), and the corners where the lines meet, left and right; the face is rolled one degree in the photo, and each figure is the mean of its two sides; where the upper face's outer edge on the end face meets the side face's (0.872 left, 0.894 right)
Aero's own views of the 15 in, straight from the side, where the step is plain in both. The view from the end, scaled down its face by the published height, has the same edge at 0.883.
Its side faces' lower edge, below the rail's top1.502 in ± 0.015 in 38.2 mmCorroboratedPhoto: Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it
Photo 1.49 in ± 0.03 in
Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630, harvested
Scale: each view's own top rail, its teeth's period by autocorrelation over 30 of them against the Picatinny pitch (std.picatinny.slot_pitch): 23.60 px a tooth, 59.94 px/in in both; heights from the teeth's tops. Read by the same bars' tone further down: a faint step, 56 to 52 at 1.487 in the left view and 60 to 52 at 1.498 in the right
The step on the side views is faint.
Photo 1.502 in ± 0.015 in used
Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it, harvested
Scale: the same end face in the same photo: across, its width at the side faces' lower edges, where it is widest (aero-r-one-15-handguard.width: 427.1 px, 284.8 px/in); down, its rail's top to its bottom flat (aero-r-one-15-handguard.height: rows 706.4 to 1228.6, 267.8 px/in: it is seen from 20 degrees above). One scale down the face serves. Read by each stretch of the end face's outline as a straight line through its own edge crossings, row by row or column by column (rms 0.1 to 0.5 px), and the corners where the lines meet, left and right; the face is rolled one degree in the photo, and each figure is the mean of its two sides; where the side face's edge meets the steep lower face's (1.488 left, 1.516 right)
The corner itself, where two fitted edges of the silhouette meet; on the side views it is a step of four tones in a bar a few pixels wide, read at 1.49 ± 0.03. 0.29 below the bore.
Width across its side faces at their upper edges1.455 in ± 0.012 in 37 mmProvisionalPhoto: Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it
Photo 1.455 in ± 0.012 in used
Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it, harvested
Scale: the same end face in the same photo: across, its width at the side faces' lower edges, where it is widest (aero-r-one-15-handguard.width: 427.1 px, 284.8 px/in); down, its rail's top to its bottom flat (aero-r-one-15-handguard.height: rows 706.4 to 1228.6, 267.8 px/in: it is seen from 20 degrees above). One scale down the face serves: the side faces' two edges land at 0.883 and 1.502 below the top where Aero's side views have them at 0.88 and 1.49. Read by each stretch of the end face's outline as a straight line through its own edge crossings, row by row or column by column (rms 0.1 to 0.5 px), and the corners where the lines meet, left and right; the face is rolled one degree in the photo, and each figure is the mean of its two sides; between the two corners where the upper faces' outer edges meet the side faces': 414.4 px where the lower corners are 427.1 apart, the left edge running out 0.058 px a row downward and the right 0.019 on a face rolled 0.015 to 0.018 (its bottom flat's slope, its centre line's)
Less than across their lower edges (the published width): each side face leans in 2.1 degrees toward its top. Not the photo's perspective: down the same face its heights keep one scale (the rail's top, these two edges and the bottom land within a pixel of a line), and its rail's head reads 0.814 across at the scale its width sets where the standard has 0.835. Two more views agree in direction: against the upright sides of the rail's neck, the far side face's edge runs out 0.02 px a row downward in Brownells' view of a shorter one from ahead (96680cef7d9e: 1.7 degrees) and 0.07 in Wing Tactical's (30f5919d7a4e).
Its bottom flat (6 o'clock), across0.609 in ± 0.015 in 15.5 mmProvisionalPhoto: Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it
Photo 0.609 in ± 0.015 in used
Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it, harvested
Scale: the same end face in the same photo: across, its width at the side faces' lower edges, where it is widest (aero-r-one-15-handguard.width: 427.1 px, 284.8 px/in); down, its rail's top to its bottom flat (aero-r-one-15-handguard.height: rows 706.4 to 1228.6, 267.8 px/in: it is seen from 20 degrees above). One scale down the face serves: the side faces' two edges land at 0.883 and 1.502 below the top where Aero's side views have them at 0.88 and 1.49. Read by each stretch of the end face's outline as a straight line through its own edge crossings, row by row or column by column (rms 0.1 to 0.5 px), and the corners where the lines meet, left and right; the face is rolled one degree in the photo, and each figure is the mean of its two sides; between the two corners where the bottom's line (the lowest dark row, column by column: rms 0.27 px over 150 columns) meets the shallow lower faces': 173.5 px
First read as 0.618 between the ends of one straight edge a side, which the outline there isn't (2026-10-05).
Width across the edges between its two lower faces (each side: the steep one under the side face, the shallow one into the bottom flat)1.133 in ± 0.015 in 28.8 mmCorroboratedPhoto: Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it
Photo 1.133 in ± 0.015 in used
Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it, harvested
Scale: the same end face in the same photo: across, its width at the side faces' lower edges, where it is widest (aero-r-one-15-handguard.width: 427.1 px, 284.8 px/in); down, its rail's top to its bottom flat (aero-r-one-15-handguard.height: rows 706.4 to 1228.6, 267.8 px/in: it is seen from 20 degrees above). One scale down the face serves: the side faces' two edges land at 0.883 and 1.502 below the top where Aero's side views have them at 0.88 and 1.49. Read by each stretch of the end face's outline as a straight line through its own edge crossings, row by row or column by column (rms 0.1 to 0.5 px), and the corners where the lines meet, left and right; the face is rolled one degree in the photo, and each figure is the mean of its two sides; between the two corners where the steep lower faces' edges meet the shallow ones': 322.6 px
Photo 1.144 in ± 0.03 in
Wing Tactical's gallery: an R-ONE from ahead and above on its right, 1280 x 1280; the photo the user sent on 2026-10-05 with "each of the m-lok slots is on its own face on the bottom half", a3e4bd3beabb, is a copy of it, harvested
Scale: the far side of the same end face against the white: its side face's two edges and its bottom flat's corner, each where two fitted stretches of the silhouette meet, set to this ledger's figures for them (side_flat_top_below_rail_top, side_flat_bottom_below_rail_top, side_top_width, width, bottom_flat_width, height), which fixes how the end face lies in the picture. Read by the silhouette's edge row by row (where the tone crosses half way), a straight line through each stretch (the upper face one stretch; under the side face two, turning 0.61 px a row to 1.02, then the bottom flat), and the corner between the two lower stretches placed among the three known ones
Photo 1.117 in ± 0.03 in
Brownells' gallery, item 430103930: a short R-ONE in OD green from ahead on its right, 1200 x 1200, harvested
Scale: the far side of the same end face against the white: its side face's two edges and its bottom flat's corner, each where two fitted stretches of the silhouette meet, set to this ledger's figures for them (side_flat_top_below_rail_top, side_flat_bottom_below_rail_top, side_top_width, width, bottom_flat_width, height), which fixes how the end face lies in the picture. Read by the silhouette's edge row by row (where the tone crosses half way), a straight line through each stretch (the upper face one stretch; under the side face two, turning 0.37 px a row to 0.60, then the bottom flat), and the corner between the two lower stretches placed among the three known ones
Another length of the R-ONE, the same section.
The view square to the section, both sides in it, scaled across by the published width. Two three-quarter views, one of them of another length, put the same edge within 0.016 of it.
The edges between its two lower faces, below the rail's top1.759 in ± 0.012 in 44.7 mmCorroboratedPhoto: Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it
Photo 1.759 in ± 0.012 in used
Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it, harvested
Scale: the same end face in the same photo: across, its width at the side faces' lower edges, where it is widest (aero-r-one-15-handguard.width: 427.1 px, 284.8 px/in); down, its rail's top to its bottom flat (aero-r-one-15-handguard.height: rows 706.4 to 1228.6, 267.8 px/in: it is seen from 20 degrees above). One scale down the face serves: the side faces' two edges land at 0.883 and 1.502 below the top where Aero's side views have them at 0.88 and 1.49. Read by each stretch of the end face's outline as a straight line through its own edge crossings, row by row or column by column (rms 0.1 to 0.5 px), and the corners where the lines meet, left and right; the face is rolled one degree in the photo, and each figure is the mean of its two sides; the corners where the steep lower faces' edges meet the shallow ones' (1.749 left, 1.768 right)
0.55 below the bore. The steep face then drops 0.257 over 0.184 (54 degrees from level) and the shallow one 0.191 over 0.262 (36): 18 degrees between them, and each as long across as the other (0.32), a row of slots down the middle of each.
Photo 1.76 in ± 0.02 in
Wing Tactical's gallery: an R-ONE from ahead and above on its right, 1280 x 1280; the photo the user sent on 2026-10-05 with "each of the m-lok slots is on its own face on the bottom half", a3e4bd3beabb, is a copy of it, harvested
Scale: the far side of the same end face against the white: its side face's two edges and its bottom flat's corner, each where two fitted stretches of the silhouette meet, set to this ledger's figures for them (side_flat_top_below_rail_top, side_flat_bottom_below_rail_top, side_top_width, width, bottom_flat_width, height), which fixes how the end face lies in the picture. Read by the silhouette's edge row by row (where the tone crosses half way), a straight line through each stretch (the upper face one stretch; under the side face two, turning 0.61 px a row to 1.02, then the bottom flat), and the corner between the two lower stretches placed among the three known ones
Photo 1.775 in ± 0.02 in
Brownells' gallery, item 430103930: a short R-ONE in OD green from ahead on its right, 1200 x 1200, harvested
Scale: the far side of the same end face against the white: its side face's two edges and its bottom flat's corner, each where two fitted stretches of the silhouette meet, set to this ledger's figures for them (side_flat_top_below_rail_top, side_flat_bottom_below_rail_top, side_top_width, width, bottom_flat_width, height), which fixes how the end face lies in the picture. Read by the silhouette's edge row by row (where the tone crosses half way), a straight line through each stretch (the upper face one stretch; under the side face two, turning 0.37 px a row to 0.60, then the bottom flat), and the corner between the two lower stretches placed among the three known ones
Another length of the R-ONE, the same section.
The view square to the section, both sides in it, scaled down by the published height. The two three-quarter views have it at 1.76 and 1.775.
The neck its rail stands on (under the rail's head, above the two upper faces), across0.62 in ± 0.015 in 15.7 mmProvisionalPhoto: Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it
Photo 0.62 in ± 0.015 in used
Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it, harvested
Scale: the same end face in the same photo: across, its width at the side faces' lower edges, where it is widest (aero-r-one-15-handguard.width: 427.1 px, 284.8 px/in); down, its rail's top to its bottom flat (aero-r-one-15-handguard.height: rows 706.4 to 1228.6, 267.8 px/in: it is seen from 20 degrees above). One scale down the face serves: the side faces' two edges land at 0.883 and 1.502 below the top where Aero's side views have them at 0.88 and 1.49; and the rail's own head beside it, 231.8 px across its widest where the standard has 0.835 in (277.6 px/in: its corners are rounded). Read by the end face's own edges under the head, where its dark gives way to the lit lugs behind it, on the rows from 770 to 790: 558.7 and 732.8, upright within 0.3 px, 174.1 px apart: 0.611 at the body's scale and 0.627 at the head's
The far side's silhouette in the two three-quarter views steps in under the head by 0.071 and 0.076 where this has 0.10: their scale across is the bottom flat's corner's, a long way from the head.
Under the head's lower 45 degree faces the end face runs straight down, upright, before the two upper faces leave it: a neck. With the standard's head (std.picatinny.top_width, lower_gauge_below_top) those faces come in to this width 0.22 below the rail's top, where the photo has the neck begin (row 765: 0.219). First read as the rail's foot, 0.72 across at 0.14 down: a place on the head's underside, and the upper faces were drawn from there, the rail a neck short (2026-10-05, the user: "Your rail height doesn't look quite right in those new models").
The neck's foot, where the two upper faces leave it, below the rail's top0.377 in ± 0.015 in 9.6 mmProvisionalPhoto: Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it
Photo 0.377 in ± 0.015 in used
Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it, harvested
Scale: the same end face in the same photo: across, its width at the side faces' lower edges, where it is widest (aero-r-one-15-handguard.width: 427.1 px, 284.8 px/in); down, its rail's top to its bottom flat (aero-r-one-15-handguard.height: rows 706.4 to 1228.6, 267.8 px/in: it is seen from 20 degrees above). One scale down the face serves: the side faces' two edges land at 0.883 and 1.502 below the top where Aero's side views have them at 0.88 and 1.49. Read by where the line through each upper face's outer edge on the end face (rms 0.3 to 0.5 px over 40 rows) meets the neck's upright edge: rows 808.1 and 806.4 (0.380 left, 0.374 right)
The corner is rounded: the edge leaves the neck's line from 0.33 down, and Aero's side views have the upper face's lit top begin at 0.33 and 0.34 down the bars between its slots, under a grey band from 0.20 that is the neck's side. The upper face then drops 0.50 over 0.42 (50 degrees from level) to the side face's upper edge, 0.65 across: twice a lower face, its two rows of slots a lower face's width apart.
Its rail's middle, between the two ears of a lug (the windows' width)0.365 in ± 0.02 in 9.3 mmProvisionalPhoto: Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it
Photo 0.365 in ± 0.02 in used
Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it, harvested
Scale: the same lugs' lit tops, edge to edge 186 to 190 px: the rail's top flat between its 45 degree faces, 0.656 in by the standard (std.picatinny.bevel_width less twice the upper gauge line's depth); the dark band outside each end is 25 px, the bevel's 0.09. Read by across the rows through two lugs that have no middle (540 and 564, 660): each ear's top 39 to 41 px, the dark between them 100 to 106
Each ear's top is then 0.14 across. The lugs with a middle are lit the same width edge to edge.
A window along its rail (the middle, open between two bridges)0.54 in ± 0.05 in 13.7 mmProvisionalPhoto: Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it
Photo 0.54 in ± 0.05 in used
Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it, harvested
Scale: the lugs' own pitch along the same stretch (std.picatinny.slot_pitch): the ears' tops come every 27 to 32 px down the columns through them, the bridges' every 52 to 62 down the middle: every other lug. Read by down the middle column, the dark between two bridges' lit tops: 38 to 41 px of the 46 between them, with the bridge's own top 10 to 14 px as the ears' are (12 to 13): a lug's length. So a window is two pitches less a lug, less 0.06 for its two ends
Brownells' view of a shorter R-ONE from above (d1035d735f06) has the same windows, rounded at their ends, about a pitch and a half long; and two round holes instead over its barrel nut, which this length's photos don't show from above.
A bridge's top below the ears' (the lugs that have a middle)0.03 in ± 0.015 in 0.8 mmProvisionalPhoto: Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it
Photo 0.03 in ± 0.015 in used
Wing Tactical's gallery: an R-ONE from its muzzle end, looking back along its rail, 1280 x 1280; the photo the user sent on 2026-10-05, 8dd2b17f2f5f, is a copy of it, harvested
Scale: heights seen from 15 degrees above the rail's plane (a pitch along the rail is 29 px where the rail's width gives 287 px/in): 277 px for an inch of height. Read by each bridge's lit top stands 7 to 10 px lower in the picture than its own lug's ears (461-470 against 453-462, 513-523 against 505-516, 570-581 against 562-574, 631-644 against 623-634): taken as lower, not further forward
It could as well be a bridge 0.03 to 0.1 in nearer the muzzle than its ears: one view can't tell height from place. Drawn as a step down.
The handguard's rear end (its two side tabs' ends) against the receiver's front face (negative: behind it)-0.763 in ± 0.02 in -19.4 mmConflictWorked out: 0in - {std.ar15.upper_barrel_thread_length} - ({.rail_front_from_rear} - {.length})
Worked out -0.763 in ± 0.02 in used
0in - {std.ar15.upper_barrel_thread_length} - ({.rail_front_from_rear} - {.length}), harvested
Aero: rail lengths "measure from end to end. This is the point of contact at the receiver to the end of the last picatinny slot at the muzzle": 15 in back from the outline's rail end (15.318 from its rear end) is 0.318 ahead of the tabs' ends, where the outline's full section starts (its top steps up at 0.30, its bottom down at 0.35).
Photo -0.778 in ± 0.04 in
Aero's gallery for the complete upper APAR700705M7, photo 1, right side; its file is named for the 223 Wylde upper, harvested
Scale: the receiver's lug holes (px 78.5, 314.4): 37.0 px/in; the handguard's rail teeth, 14.43 px a tooth, along it. Read by the handguard's first full tooth at px 334.0, 0.535 ahead of the pivot hole; its outline puts that tooth 0.6515 ahead of its rear end: the rear end 6.258 ahead of the takedown pin, against the receiver's front face at 7.036
Photo -0.775 in ± 0.04 in
Aero's gallery for the complete upper APAR700705M7, photo 2, left side, harvested
Scale: the receiver's lug holes (px 692.5, 928.2): 36.97 px/in; the rail teeth 14.655 px. Read by the first full tooth at px 672.5, 0.537 ahead of the pivot hole: the rear end 6.261 ahead of the takedown pin; its own visible edge at px 696 reads 6.28
Worked out -0.445 in ± 0.01 in
0in - {std.ar15.upper_barrel_thread_length}, harvested
The contact face, not the outline's rear end: what the ledger had until 2026-10-03.
Aero's own rule for its length, on its own outline; both photos of the complete upper agree with it within 0.015 in.
derived and shoulder differ by 0.318 in beyond what each states it is good to.
kit-right and shoulder differ by 0.333 in beyond what each states it is good to.
kit-left and shoulder differ by 0.33 in beyond what each states it is good to.
The outline's x = 0 is the ends of two tabs that reach back along the receiver's front ring; the face that meets the receiver (Aero's "point of contact at the receiver") is 0.318 ahead of them, at the receiver's front shoulder, where the barrel-nut thread begins. Until 2026-10-03 the tabs' ends were taken as that face, which put the handguard 0.32 in too far forward: it ran past the barrel's shoulder over the muzzle device.
The room inside its side faces, from the face in to the barrel (what an M-LOK accessory's nuts may take)No value yetMissingNo source yet
Not sourced: the barrel under it is another part, and its diameter under the handguard isn't on file (its traced photo shows it ahead of the handguard only).
Its rail's front end (the end of the last slot) ahead of the outline's rear end15.318 in ± 0.02 in 389.1 mmProvisionalPhoto: Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630
Photo 15.318 in ± 0.02 in used
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in. Read by the outline's top flat ahead of the last slot, to x 15.318
Its rail's rearmost slot (its centre) ahead of the outline's rear end0.855 in ± 0.02 in 21.7 mmProvisionalPhoto: Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630
Photo 0.855 in ± 0.02 in used
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: the rail's own slots beside it: its last eight pitches at the standard's 0.394 in (std.picatinny.slot_pitch) are 59.32 px/in there (60.49 at the muzzle end: the lens stood nearer the middle). Read by the gaps between the teeth in the rows of the tooth tops (245 to 248), each edge at the 50% level: the rearmost gap's centre is 50.7 px ahead of the outline's rear end. A slot seen obliquely narrows about its own middle (13 px wide near the lens's axis, 7 at this end), so its centre holds
With rear_x it puts that slot 7.13 in ahead of the takedown pin on Aero's M4E1 Threaded upper: 2.15 pitches ahead of that receiver's last slot (6.285), each from its own photo. Two whole pitches is within what the two readings and the handguard's place carry between them (about 0.05 in), so the rails may well share one grid; nothing is assumed either way. 2026-10-12, when the model's slots were cut on this grid (they had been the outline's own): the traced outline has its first gap 0.001 in from this figure and its last 0.005 from where 36 pitches on put it, and between them its gaps bow up to 0.044 in behind the grid (slots 12 to 17), because the outline has one scale end to end over a photo whose scale rises 2% from the rear to the muzzle; a rail is machined to an even pitch, so the grid is the rail and the bow the photo. The ± covers the gap's centre (half a pixel, 0.008) and the scale beside it. It doesn't cover the outline's rear end, which this is counted from: that is the near tab's end, 0.6 in nearer the lens than the rail's middle and 10 in off its axis, and reads behind where the tab ends by that over the lens's distance (about 0.1 in if the lens was 65 in off, as the slots' narrowing has it). Where the grid stands on a rifle doesn't rest on that end: rear_x is 15 in back from the rail's front end less the same outline's length, so the first slot stands (rail_front_from_rear − this) behind the rail's front end, both read on the rail.
Slots in its top rail37ProvisionalPhoto: Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630
Photo 37 count used
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: none: a count. Read by the gaps between the teeth along the whole rail, each at least 7 px wide and 22.7 to 24.8 px from the next: 37
The thin slots' first centre ahead of the outline's rear end (all four rows)2.987 in ± 0.02 in 75.9 mmProvisionalPhoto: Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630
Photo 2.987 in ± 0.02 in used
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in. Read by the see-through slots' centres in the four rows fitted to one pitch
The thin slots' pitch along each row1.069 in ± 0.006 in 27.1 mmProvisionalPhoto: Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630
Photo 1.0685 in ± 0.006 in used
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in. Read by 11 pitches over 11.753 in, the rows above and below the M-LOK row; the complete upper's photo 0a6c8a661544 reads 1.055
Thin slots in each row12ProvisionalPhoto: Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630
Photo 12 count used
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in. Read by counted in each of the four rows
A thin slot's length (at least: what shows through both walls)0.954 in ± 0.02 in 24.2 mmProvisionalPhoto: Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630
Photo 0.954 in ± 0.02 in used
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in. Read by the longest see-through slot in the two inner rows, 57 px
A thin slot's width, across the slanted face it is in0.22 in ± 0.04 in 5.6 mmConflictPhoto: Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630
Photo 0.12 in ± 0.02 in
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in. Read by the widest see-through height in a row, the upper outer row's (0.61 to 0.73 above the bore); the others show 0.05 to 0.117
Photo 0.22 in ± 0.04 in used
Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630, harvested
Scale: each view's own top rail, its teeth's period by autocorrelation over 30 of them against the Picatinny pitch (std.picatinny.slot_pitch): 23.60 px a tooth, 59.94 px/in in both; heights from the teeth's tops. Read by the opening on the near wall: down the columns through the slots' middles the tone leaves the bars' over 0.17 to 0.19 in (the inner rows: 0.66 to 0.83 and 1.52 to 1.71 below the rail's top; the part that shows through both walls is the half of it nearer the side flat). Seen from the side on faces that stand 54 degrees from level (the steep lower one) and 50 (the upper), that is 0.23 and 0.22 across the face
One width is drawn for all four rows. Two thirds of the face it is in: the two lower faces are 0.32 across, the upper one 0.66 with two rows.
The opening itself. What shows through both walls (0.12) is less: the far wall and the floor stand behind the rest of it.
photo and opening differ by 0.1 in beyond what each states it is good to.
The upper outer row of thin slots, its height above the bore0.71 in ± 0.02 in 18 mmConflictPhoto: Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630
Photo 0.66 in ± 0.02 in
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in; the top at rail_top_above_bore. Read by the see-through slots' vertical centres (0.61 to 0.73)
Photo 0.71 in ± 0.02 in used
Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630, harvested
Scale: each view's own top rail, its teeth's period by autocorrelation over 30 of them against the Picatinny pitch (std.picatinny.slot_pitch): 23.60 px a tooth, 59.94 px/in in both; heights from the teeth's tops. Read by the middle of the opening on the near wall, 0.41 to 0.59 below the rail's top (0.384 to 0.59 in the left view, 0.434 to 0.59 in the right), with the rail's top at rail_top_above_bore
Where the opening is on the face it is cut in, which the model cuts. The earlier reading is the middle of what shows through both walls, the opening's half nearer the side flat.
photo and opening differ by 0.05 in beyond what each states it is good to.
The upper inner row of thin slots, its height above the bore0.46 in ± 0.02 in 11.7 mmCorroboratedPhoto: Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630
Photo 0.443 in ± 0.02 in
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in; the top at rail_top_above_bore. Read by the see-through slots' vertical centres (0.393 to 0.493)
Photo 0.46 in ± 0.02 in used
Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630, harvested
Scale: each view's own top rail, its teeth's period by autocorrelation over 30 of them against the Picatinny pitch (std.picatinny.slot_pitch): 23.60 px a tooth, 59.94 px/in in both; heights from the teeth's tops. Read by the middle of the opening on the near wall, 0.67 to 0.84 below the rail's top (0.66 to 0.835, 0.684 to 0.851), with the rail's top at rail_top_above_bore
Where the opening is on the face it is cut in, which the model cuts. The earlier reading is the middle of what shows through both walls, the opening's half nearer the side flat.
The lower inner row of thin slots, its height above the bore-0.41 in ± 0.02 in -10.4 mmCorroboratedPhoto: Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630
Photo -0.385 in ± 0.02 in
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in; the top at rail_top_above_bore. Read by the see-through slots' vertical centres (-0.444 to -0.327)
Photo -0.41 in ± 0.02 in used
Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630, harvested
Scale: each view's own top rail, its teeth's period by autocorrelation over 30 of them against the Picatinny pitch (std.picatinny.slot_pitch): 23.60 px a tooth, 59.94 px/in in both; heights from the teeth's tops. Read by the middle of the opening on the near wall, 1.525 to 1.715 below the rail's top (1.518 to 1.71, 1.535 to 1.72), with the rail's top at rail_top_above_bore
Where the opening is on the face it is cut in, which the model cuts. The earlier reading is the middle of what shows through both walls, the opening's half nearer the side flat.
The lower outer row of thin slots, its height above the bore-0.635 in ± 0.02 in -16.1 mmCorroboratedPhoto: Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630
Photo -0.6 in ± 0.02 in
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in; the top at rail_top_above_bore. Read by the see-through slots' vertical centres (-0.628 to -0.578)
Photo -0.635 in ± 0.02 in used
Aero's gallery: the R-ONE 15 in handguard from its left and from its right, each 1000 x 630, harvested
Scale: each view's own top rail, its teeth's period by autocorrelation over 30 of them against the Picatinny pitch (std.picatinny.slot_pitch): 23.60 px a tooth, 59.94 px/in in both; heights from the teeth's tops. Read by the opening on the near wall begins 1.78 below the rail's top (1.77, 1.785); below that the face is too dark to show its end. It is in the shallow lower face, which stands 36 degrees from level (lower_edge_width, lower_edge_below_rail_top): an opening of the other rows' width across that face (thin_slot_width) is 0.13 tall from the side, so its middle is 1.845 down, with the rail's top at rail_top_above_bore
First taken to end where row a's does, mirrored about the M-LOK row, on one lower face at 46 degrees: -0.66 (2026-10-05). The shallow face runs from 1.759 to 1.95 down: its middle is 0.642 below the bore, and what shows through both walls (the opening's upper part on a face this shallow, 1.785 to 1.835) is what an opening there would show.
Where the opening is on the face it is cut in, which the model cuts. The earlier reading is the middle of what shows through both walls, the opening's half nearer the side flat.
The short slot behind the M-LOK slots (in their row), its rear end ahead of the outline's rear end3.539 in ± 0.02 in 89.9 mmProvisionalPhoto: Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630
Photo 3.539 in ± 0.02 in used
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in. Read by the see-through slot from 3.539 to 3.856 (0.317 long), y -0.093 to 0.175: the M-LOK row's height
The short slot's length0.317 in ± 0.02 in 8.1 mmProvisionalPhoto: Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630
Photo 0.317 in ± 0.02 in used
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in. Read by as short_slot_rear_from_rear
The QD sling socket on each side (3 and 9 o'clock), its centre ahead of the outline's rear end2.685 in ± 0.03 in 68.2 mmProvisionalPhoto: Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630
Photo 2.685 in ± 0.03 in used
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in. Read by a round hole about 22 px across at px 800 (mirrored); only 0.18 x 0.32 shows through
Aero: "Quick disconnect sling socket at the 3, 6 and 9 o'clock positions". The one underneath isn't seen from the side.
The QD sling socket's diameter, as it shows0.37 in ± 0.03 in 9.4 mmProvisionalPhoto: Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630
Photo 0.37 in ± 0.03 in used
Aero's gallery: the R-ONE 15 in handguard from the side, 1000 x 630, harvested
Scale: its top rail's 37 teeth fitted to the Picatinny pitch (std.picatinny.slot_pitch): 23.548 px a tooth, 59.77 px/in. Read by the round hole's outline, about 22 px
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Handguard mount
Picatinny rail (MIL-STD-1913)
- Red dot mounts
- Aimpoint Duty RDS One-piece TNP Mount, 30 mm, Aimpoint LRP (Lever Release Picatinny) Mount with 39 mm Spacer, for Micro, Aimpoint One-piece Torsion Nut Mount and Spacer, 39 mm, Geissele Super Precision T1 Mount - 1.93" Height, Geissele Super Precision T1 Mount - Absolute Co-Witness, Geissele Super Precision T1 Mount - Lower 1/3 Co-Witness, Holosun 1.63 in lower 1/3 co-witness pedestal mount (HS-MOUNT-AR-RISER-ARO), Midwest Industries MK2 QD T2 Aimpoint Mount, Low, Midwest Industries MK2 QD T2 Aimpoint Mount, Lower 1/3 Cowitness, Midwest Industries MK2 QD T2 Aimpoint Mount, NV 2.26 in Height, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – 1.93″ HEIGHT, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – LOWER 1/3 (39MM HEIGHT), Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.42 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.57 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.93 in, Scalarworks LEAP/02 Aimpoint Micro T-2 quick-detach mount, 2.26 in, SIG Sauer M1913 I-BEAM Mount, 1.41 in absolute co-witness, SIG Sauer See-Through Riser Mount, 1.41 in absolute co-witness, Unity Tactical FAST Micro Mount, 2.26 in optical centerline
- Optics
- Aimpoint Patrol Rifle Optic (PRO) Red Dot Reflex Sight - QRP2 Mount, EOTECH HWS EXPS3 holographic weapon sight, 1-Dot Speed Ring, Holosun HS510C Open Reflex MRS Solar QD Mount
- Lights
- Olight Baldr S BL, Streamlight ProTac Rail Mount HL-X, SureFire Mini Scout Light Pro, SureFire Scout Light Pro Dual Fuel
- Backup sights
- Daniel Defense A1.5 Fixed Rear Sight, Daniel Defense Rail Mounted Fixed Front Sight, Magpul MBUS 3 Sight – Front, Magpul MBUS 3 Sight – Rear, Magpul MBUS Pro Sight – Front, Magpul MBUS Pro Sight – Rear
- Magnifiers
- EOTECH G33 Magnifier, STS Mount, EOTECH G45 Magnifier, STS Mount, Holosun HM3X 3× magnifier with flip mount
- Scope mounts
- Primary Arms Deluxe AR-15 Scope Mount - 30mm, Primary Arms SLx Cantilever 30mm Mount - 1.5", Reptilia AUS™ MOUNT - 30MM DIAMETER - 39MM HEIGHT, Scalarworks LEAP/08 quick-detach scope mount, 30 mm, 1.57 in, SIG SAUER ALPHA-MSR scope mount, 30 mm, Vortex Sport Cantilever 30mm Mount
M-LOK
- Hand stops
- BCM KAG (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK Hand Stop (fit unchecked), Magpul M-LOK Index Panel (fit unchecked)
- Vertical grips
- BCM Vertical Grip Mod 3 (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK MVG vertical grip (fit unchecked)
- Lights
- Cloud Defensive REIN (fit unchecked), Streamlight ProTac Rail Mount HL-X (fit unchecked), SureFire Mini Scout Light Pro (fit unchecked), SureFire Scout Light Pro Dual Fuel (fit unchecked)
- Rail sections
- Magpul M-LOK® Aluminum Rail, 3 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 5 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 7 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 9 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 11 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 3 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 5 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 7 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 9 Slots (fit unchecked)
- Adapter plates
- Magpul M-LOK Hand Stop MOE Adapter (fit unchecked)
- Sling mounts
- Magpul M-LOK QD Sling Mount (fit unchecked)
- Rail covers
- Magpul M-LOK Rail Cover Type 2 (fit unchecked)
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Aero Precision $122.50 SOCOM Blue Cerakote Nov 21, 2026, stock not said
- Aero Precision $225.00 Anodized Black Nov 21, 2026, stock not said
- Aero Precision $225.00 OD Green Anodized Nov 21, 2026, stock not said
- Aero Precision $225.00 Kodiak Brown Anodized Nov 21, 2026, stock not said
- Aero Precision $245.00 OD Green Cerakote Nov 21, 2026, stock not said