Red dot mount
Reptilia DOT MOUNT FOR AIMPOINT® MICRO – 1.93″ HEIGHT
Reptilia's one-piece red dot mount for the Aimpoint Micro footprint: "Machined from billet 7075-T6 aluminum with Milspec Type III hard anodized finish, the 1.93 DOT Mount attaches to any M1913 Picatinny rail to place the optical axis at 1.93 inches above the rail. Its spring-loaded nitrided steel clamp and mounting bolt simplify the installation process, and sit flush with the body of the mount for a low-profile, anti-snag design." 55 grams. The page is headed "DOT Mount for Aimpoint T-1/T-2/CompM5 – 1.93″ Height" and every photograph on it has a CompM5 on the mount.

- Weight
- 1.94 oz Confirmedpublished: Reptilia, DOT MOUNT FOR AIMPOINT® MICRO - 1.93" HEIGHT (product page), the maker, read Nov 3, 2026
- Lowest price
- $98.96 at AR15Discounts, read Nov 21, 2026 (Black Anodized)
- Maker's number
- 100-037
- Colours
- Black Anodized, Flat Dark Earth Anodized
- Drawn as
- modelled
- Maker's page
- reptiliacorp.com
In “22RB .22 LR rifle”, a build on the start page, in place of its Holosun 1.63 in lower 1/3 co-witness pedestal mount (HS-MOUNT-AR-RISER-ARO).
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Optical axis above the rail's top, as the maker gives it (no dot named: its pictures show a CompM5)1.93 in ± 0.005 in 49 mmConfirmedPublished: Reptilia, DOT MOUNT FOR AIMPOINT® MICRO - 1.93" HEIGHT (product page), the maker, read Nov 3, 2026
Published “the 1.93 DOT Mount attaches to any M1913 Picatinny rail to place the optical axis at 1.93 inches above the rail.” used
Reptilia, DOT MOUNT FOR AIMPOINT® MICRO - 1.93" HEIGHT (product page), the maker, read Nov 3, 2026 the page, harvested Nov 3, 2026
Published “Mount Height 1.93 in.”
Primary Arms, Reptilia Corp DOT Mount for Aimpoint Micro - Black - 1.93", a seller, read Nov 3, 2026 the page, harvested Nov 3, 2026
The maker's own sentence; Primary Arms repeats the figure.
The maker's only height. The page names no dot; it is headed "DOT Mount for Aimpoint T-1/T-2/CompM5 – 1.93″ Height", lists twenty-odd Micro-footprint dots as compatible, and every photograph of it on the page has an Aimpoint CompM5 on it. Its article on the height: "A 1.93-inch optic height refers to the approximate distance from the centerline of the optic to the rail of the rifle" (https://reptiliacorp.com/understanding-1-93-inch-optic-heights/, as the discovery read it).
The CompM5's axis above the rail's top in the maker's on-rifle view (a check of the view's scale against the maker's figure)1.917 in ± 0.02 in 48.7 mmProvisionalPhoto: the maker's LEFT-SIDE-MOUNTED-FOR-site.jpg: a CompM5 on the FDE mount on a receiver, square from the left, level, 1000 x 1000
Photo 1.917 in ± 0.02 in used
the maker's LEFT-SIDE-MOUNTED-FOR-site.jpg: a CompM5 on the FDE mount on a receiver, square from the left, level, 1000 x 1000, harvested
Scale: the receiver's rail teeth beside the base: four tooth centres at row 772, 746.5, 817.0, 887.5 and 958.5 px, 70.67 px a slot (the standard's 0.3937 in): 179.5 px/in; the slots' floor reads 21 px (0.117 in) under the tooth tops, the standard's 0.118. Read by the front cover ring's top and bottom edges in columns 218 to 236 (dark runs 321.5 to 525 px), its middle 423.3 px; the tooth tops at 767.3 px
Not a figure of the mount's: the CompM5 isn't on file. The front lens cover's ring, read where its top shows under the cover's hinge (row 321.5) and at its bottom (525): its middle, the lens's axis, 1.917 in over the tooth tops (767.3). The maker's 1.93 for the dot pictured lands within 0.013 in: the rail's scale and the maker's figure agree.
The deck's lips' top (the outline's top, where a side view sees the dot's base meet the deck) above the rail's top1.41 in ± 0.015 in 35.8 mmProvisionalPhoto: the maker's LEFT-SIDE-MOUNTED-FOR-site.jpg: a CompM5 on the FDE mount on a receiver, square from the left, level, 1000 x 1000
Photo 1.41 in ± 0.015 in used
the maker's LEFT-SIDE-MOUNTED-FOR-site.jpg: a CompM5 on the FDE mount on a receiver, square from the left, level, 1000 x 1000, harvested
Scale: the receiver's rail teeth beside the base: four tooth centres at row 772, 746.5, 817.0, 887.5 and 958.5 px, 70.67 px a slot (the standard's 0.3937 in): 179.5 px/in; the slots' floor reads 21 px (0.117 in) under the tooth tops, the standard's 0.118. Read by the tan deck's top edge over columns 350 to 650 (first tan pixel at 514 to 515; the CompM5's black base above it) to the tooth tops beside the base (767.3): 253 px
The deck has two raised lips along its long edges, and a dot's base stands between them on the floor (lip_height lower). From the side the near lip hides the base's foot: the seam a side view sees is the lip's top.
The lips' height above the deck's floor0.03 in ± 0.02 in 0.8 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file is square on to the deck's end. Primary Arms' view from the right and above (932ddb83c5e0) has each lip's inner wall about a quarter of the deck plate's lettered side face high.
Worked out 0.03 in ± 0.02 in used
An assumption for the drawing, not a reading: no view on file is square on to the deck's end. Primary Arms' view from the right and above (932ddb83c5e0) has each lip's inner wall about a quarter of the deck plate's lettered side face high., harvested
The deck's floor (where a dot's base sits) above the rail's top1.38 in ± 0.025 in 35.1 mmProvisionalWorked out: {.lip_top_above_rail} - {.lip_height}
Worked out 1.341 in ± 0.04 in
{.optical_height} - {aimpoint-micro-t-2.axis_above_base}, harvested
1.93 in less the T-2's 0.589 in.
Worked out 1.38 in ± 0.025 in used
{.lip_top_above_rail} - {.lip_height}, harvested
1.41 in less the lips' 0.03 in.
A reading of the deck itself, on the maker's own view of this mount on a rail; the other is the maker's figure for a CompM5 worked out with a T-2's axis, which the same view puts 0.05 in too high for the dot pictured. The two agree within their ±.
Worked out two ways. From the maker's height with the T-2's axis over its base: the Micro the mount is named for, and the only Micro on file whose axis over its own base is read (the CompM5 the maker's pictures show isn't on file). And read on the maker's view of the mount on a rail, from the lips' top less their height. They agree within their ±; the reading is the deck itself and is adopted. The maker's figure is for the CompM5 it pictures, whose axis stands 1.917 − 1.38 = 0.54 in over this floor in that view: 0.05 under the T-2's 0.589 (aimpoint-micro-t-2.axis_above_base), the difference between the two measurements. Scalarworks' drawing of its 1.93 in mount with a T-2 on it (scalarworks-SW0120-diagram-A.png, filed with scalarworks-leap-01-micro-193 as c5d15b40764b: "1.93" OPTIC CENTER") has the T-2's axis about 0.53 in over the mount's top, as this view has the CompM5's: the T-2's 0.589 may be high.
The footprint's middle along the deck, ahead of the clamp's middle0 in ± 0.02 in 0 mmProvisionalPhoto: the maker's LEFT-SIDE-MOUNTED-FOR-site.jpg: a CompM5 on the FDE mount on a receiver, square from the left, level, 1000 x 1000
Photo 0 in ± 0.02 in used
the maker's LEFT-SIDE-MOUNTED-FOR-site.jpg: a CompM5 on the FDE mount on a receiver, square from the left, level, 1000 x 1000, harvested
Scale: the receiver's rail teeth beside the base: four tooth centres at row 772, 746.5, 817.0, 887.5 and 958.5 px, 70.67 px a slot (the standard's 0.3937 in): 179.5 px/in; the slots' floor reads 21 px (0.117 in) under the tooth tops, the standard's 0.118. Read by the deck's top (columns 330 to 671 at row 518, middle 500.5) over the base's foot (317 to 682 at row 790, middle 499.5) and the cross bolt's head (middle 500): the deck stands centred over the base and its bolt within a pixel, and its four screw holes and key lie about its middle in the views from above (932ddb83c5e0, ae40bf4e074b)
The base's length along the rail (at its foot)2.039 in ± 0.015 in 51.8 mmProvisionalPhoto: the maker's LEFT-SIDE-MOUNTED-FOR-site.jpg: a CompM5 on the FDE mount on a receiver, square from the left, level, 1000 x 1000
Photo 2.039 in ± 0.015 in used
the maker's LEFT-SIDE-MOUNTED-FOR-site.jpg: a CompM5 on the FDE mount on a receiver, square from the left, level, 1000 x 1000, harvested
Scale: the receiver's rail teeth beside the base: four tooth centres at row 772, 746.5, 817.0, 887.5 and 958.5 px, 70.67 px a slot (the standard's 0.3937 in): 179.5 px/in; the slots' floor reads 21 px (0.117 in) under the tooth tops, the standard's 0.118. Read by the base's two ends at row 790 (317 to 682, the tan silhouette against the black receiver and the white ground): 366 px
The base's foot below the rail's top0.223 in ± 0.02 in 5.7 mmProvisionalPhoto: Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853
Photo 0.223 in ± 0.02 in used
Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853, harvested
Scale: the base's length, mount_length = 2.039 in over its 627 px: 307.5 px/in. Read by the traced outline's foot 1.633 in under its top (the lips' top), less lip_top_above_rail (1.41 in, the maker's on-rifle view); on that view the foot is in the base's shadow against the black receiver, and the lit rim under the bolt's head reaches 806 px, 0.21 in under the tooth tops
The deck plate's side face, from the lips' top down to where its underside turns into the stem0.132 in ± 0.01 in 3.4 mmProvisionalPhoto: Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853
Photo 0.132 in ± 0.01 in used
Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853, harvested
Scale: mount_length over the outline's 627 px: 307.5 px/in. Read by the lettered band down the deck's side, rows 197.5 to 238 (40.5 px); the outline's ends turn at 0.13 and 0.133 under its top
The base's square ends, from its foot to where its top turns up into the stem0.368 in ± 0.012 in 9.3 mmProvisionalPhoto: Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853
Photo 0.368 in ± 0.012 in used
Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853, harvested
Scale: mount_length over the outline's 627 px: 307.5 px/in. Read by the traced outline's ends: the corner at 1.265 in under its top at both ends, its foot at 1.633
Each I-beam flange's thickness along the rail (from the waist's silhouette in to the web's face)0.2 in ± 0.03 in 5.1 mmProvisionalPhoto: Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853
Photo 0.2 in ± 0.03 in used
Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853, harvested
Scale: mount_length over the outline's 627 px: 307.5 px/in. Read by the waist's silhouette (455 and 773 px at row 400) to the lit inner edge of each flange, where the web's face begins (about 520 and 712 px): 65 and 61 px
The I-beam's web across the rifle, between its two flanges0.1 in ± 0.08 in 2.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: inside what the maker's two weights leave for the web (the note), where the views from the right and front show the web's face well inside the flange's (be5535ecdde1, 932ddb83c5e0).
Worked out 0.1 in ± 0.08 in used
An assumption for the drawing, not a reading: inside what the maker's two weights leave for the web (the note), where the views from the right and front show the web's face well inside the flange's (be5535ecdde1, 932ddb83c5e0)., harvested
No view on file is square on to the mount's end, and no page gives it. The maker's two weights bound it: the 1.93 (55 g) and the lower 1/3 (51 g) differ by 4 g (± 1 g, each to its gram), 0.087 in³ of 7075 (std.density.aluminium_7075), over the 0.33 in their stems' heights differ by (1.133 and 0.805 in between the deck plate and the base, by their outlines and readings): 0.265 ± 0.07 in² of metal in a stem's section at its waist. The two flanges, flange_thickness along the rail by the stem's width across, are 0.22 of that, which leaves the web between them (about 0.62 in long) 0.07 ± 0.11 in thick. Drawn at 0.1.
Width across the rifle (the deck and the base)1.24 in ± 0.01 in 31.5 mmProvisionalWorked out: {reptilia-dot-mount-39mm.width}
Worked out 1.24 in ± 0.01 in used
{reptilia-dot-mount-39mm.width}, harvested
31.5 mm, the lower 1/3's (the reader's "Width- 31.5mm").
No view or page gives this height's width: the lower 1/3's, as a reader measured it, the only width on file. The two heights' decks and bases read the same lengths and depths in their side views (mount_length, deck_plate_thickness, base_end_height), and the maker's three-quarter views of the two look alike across.
The I-beam across the rifle at its narrowest (its two flanges, the outside a caliper reaches)0.551 in ± 0.02 in 14 mmProvisionalWorked out: {reptilia-dot-mount-39mm.stem_width}
Worked out 0.551 in ± 0.02 in used
{reptilia-dot-mount-39mm.stem_width}, harvested
14 mm, the lower 1/3's.
No view or page gives it for this height: the lower 1/3's, as a reader measured it, the only figure on file.
The cross bolt's axis above the base's foot0.226 in ± 0.01 in 5.7 mmProvisionalPhoto: Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853
Photo 0.226 in ± 0.01 in used
Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853, harvested
Scale: mount_length over the outline's 627 px: 307.5 px/in. Read by the round seat's middle (612, 628 px) over the foot (697.5)
The round seat the cross bolt's head lies flush in (on the left face)0.403 in ± 0.012 in 10.2 mmProvisionalPhoto: Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853
Photo 0.403 in ± 0.012 in used
Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853, harvested
Scale: mount_length over the outline's 627 px: 307.5 px/in. Read by the seat's lit outer rim, 550 to 674 px across at row 628
The cross bolt's head0.306 in ± 0.012 in 7.8 mmProvisionalPhoto: Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853
Photo 0.306 in ± 0.012 in used
Rifle Supply 125332.png: the black 1.93 alone, square from the left, transparent ground, 1280 x 853, harvested
Scale: mount_length over the outline's 627 px: 307.5 px/in. Read by the head's dark disc inside the seat, about 94 px across
How far the seat's floor (the head's face) lies inside the base's left face0.02 in ± 0.02 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the maker says the clamp and bolt "sit flush with the body of the mount"; the views show a lit rim round the head, which is drawn as a seat this deep.
Worked out 0.02 in ± 0.02 in used
An assumption for the drawing, not a reading: the maker says the clamp and bolt "sit flush with the body of the mount"; the views show a lit rim round the head, which is drawn as a seat this deep., harvested
The slot across the bolt's head0.045 in ± 0.015 in 1.1 mmProvisionalWorked out: An assumption for the drawing, not a reading: the slot shows across the head in every left view, about a seventh of the head's width; no view gives its depth (drawn as deep as it is wide).
Worked out 0.045 in ± 0.015 in used
An assumption for the drawing, not a reading: the slot shows across the head in every left view, about a seventh of the head's width; no view gives its depth (drawn as deep as it is wide)., harvested
The steel clamp's length along the rail (on the right face)0.6 in ± 0.1 in 15.2 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view is square on to the right face. In the views from the right and above (932ddb83c5e0, ae40bf4e074b) the clamp's faceted body is about three tenths of the base's length.
Worked out 0.6 in ± 0.1 in used
An assumption for the drawing, not a reading: no view is square on to the right face. In the views from the right and above (932ddb83c5e0, ae40bf4e074b) the clamp's faceted body is about three tenths of the base's length., harvested
The steel clamp's top above the base's foot0.33 in ± 0.06 in 8.4 mmProvisionalWorked out: An assumption for the drawing, not a reading: in the views from the right the clamp's body reaches nearly to the base's top edge, a little under base_end_height.
Worked out 0.33 in ± 0.06 in used
An assumption for the drawing, not a reading: in the views from the right the clamp's body reaches nearly to the base's top edge, a little under base_end_height., harvested
How far the steel clamp stands out of the base's right face0.05 in ± 0.03 in 1.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: the maker says it sits "flush with the body"; the views from the right show its faceted face standing a little proud.
Worked out 0.05 in ± 0.03 in used
An assumption for the drawing, not a reading: the maker says it sits "flush with the body"; the views from the right show its faceted face standing a little proud., harvested
The cross bolt's end, where it stands out of the steel clamp0.16 in ± 0.04 in 4.1 mmProvisionalWorked out: An assumption for the drawing, not a reading: a round end in the clamp's middle in the views from the right, about half the head's width.
Worked out 0.16 in ± 0.04 in used
An assumption for the drawing, not a reading: a round end in the clamp's middle in the views from the right, about half the head's width., harvested
The four through holes in the base's top, either side of the stem0.12 in ± 0.03 in 3 mmProvisionalWorked out: An assumption for the drawing, not a reading: four round holes through the base's top, two either side of the stem, show in the views from above and come out in the channel's roof (125330_A of the lower 1/3, the same base); about a twentieth of the base's length across.
Worked out 0.12 in ± 0.03 in used
An assumption for the drawing, not a reading: four round holes through the base's top, two either side of the stem, show in the views from above and come out in the channel's roof (125330_A of the lower 1/3, the same base); about a twentieth of the base's length across., harvested
The base's holes ahead of and behind the clamp's middle0.78 in ± 0.08 in 19.8 mmProvisionalWorked out: An assumption for the drawing, not a reading: near the base's ends, outside the flare into the stem, in the views from above (ae40bf4e074b).
Worked out 0.78 in ± 0.08 in used
An assumption for the drawing, not a reading: near the base's ends, outside the flare into the stem, in the views from above (ae40bf4e074b)., harvested
The base's holes out from the middle across the rifle0.4 in ± 0.06 in 10.2 mmProvisionalWorked out: An assumption for the drawing, not a reading: between the flanges and the base's edges in the views from above (ae40bf4e074b), and over the rail's head's edges in the view from below (125330_A).
Worked out 0.4 in ± 0.06 in used
An assumption for the drawing, not a reading: between the flanges and the base's edges in the views from above (ae40bf4e074b), and over the rail's head's edges in the view from below (125330_A)., harvested
The four holes for the dot's screws through the deck plate0.17 in ± 0.03 in 4.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: four round holes inside the lips in the views from above (932ddb83c5e0), about a twelfth of the deck's length across.
Worked out 0.17 in ± 0.03 in used
An assumption for the drawing, not a reading: four round holes inside the lips in the views from above (932ddb83c5e0), about a twelfth of the deck's length across., harvested
The deck's screw holes ahead of and behind the footprint's middle0.62 in ± 0.1 in 15.7 mmProvisionalWorked out: An assumption for the drawing, not a reading: in Primary Arms' three-quarter view from above (932ddb83c5e0) the two pairs are about 0.63 of the deck's length apart, a ratio read along an oblique edge.
Worked out 0.62 in ± 0.1 in used
An assumption for the drawing, not a reading: in Primary Arms' three-quarter view from above (932ddb83c5e0) the two pairs are about 0.63 of the deck's length apart, a ratio read along an oblique edge., harvested
The deck's screw holes out from the middle across the rifle0.31 in ± 0.06 in 7.9 mmProvisionalWorked out: An assumption for the drawing, not a reading: in the same view the two holes of a pair are about half the deck's width apart.
Worked out 0.31 in ± 0.06 in used
An assumption for the drawing, not a reading: in the same view the two holes of a pair are about half the deck's width apart., harvested
The machined edges' break0.006 in ± 0.004 in 0.2 mmProvisionalWorked out: An assumption for the drawing, not a reading: every edge in the photographs is broken a little; no view resolves by how much.
Worked out 0.006 in ± 0.004 in used
An assumption for the drawing, not a reading: every edge in the photographs is broken a little; no view resolves by how much., harvested
The chamfer along the base's two lower outer edges (the jaws' feet)0.05 in ± 0.02 in 1.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: Rifle Supply's view of the lower 1/3 from below (a copy on file) has a lit strip along the near jaw's lower outer edge, about a fortieth of the base's length across (0.04 to 0.05 in); no view is square on to the base's end. The same base in both heights' side views.
Worked out 0.05 in ± 0.02 in used
An assumption for the drawing, not a reading: Rifle Supply's view of the lower 1/3 from below (a copy on file) has a lit strip along the near jaw's lower outer edge, about a fortieth of the base's length across (0.04 to 0.05 in); no view is square on to the base's end. The same base in both heights' side views., harvested
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Picatinny rail (MIL-STD-1913)
- Uppers
- Aero Precision M4E1 Enhanced Upper Receiver Stripped, Aero Precision M4E1 Threaded upper receiver, BCM M4 Upper Receiver Assembly (w/ Laser T-Markings), Expo Arms 7075 Stripped AR-15 Upper Receiver, Geissele Automatics Super Duty Stripped Upper Receiver, Nordic Components 22RB .22 LR upper, 16", Palmetto State Armory AR-15 Stripped Upper Receiver, Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12", Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16"
- Handguards
- Aero Precision AR15 10.3" R-ONE M-LOK handguard, Aero Precision AR15 12.7" R-ONE M-LOK handguard, Aero Precision AR15 15" Enhanced M-LOK Handguard, Gen 2, Aero Precision AR15 15" R-ONE M-LOK handguard, Aero Precision AR15 15" S-ONE M-LOK Handguard, Aero Precision AR15 16.6" R-ONE M-LOK handguard, Aero Precision AR15 7.3" R-ONE M-LOK handguard, Aero Precision AR15 9.3" R-ONE M-LOK handguard, BCM MCMR-10 (M-LOK® Compatible* Modular Rail), BCM MCMR-13 (M-LOK® Compatible* Modular Rail), BCM MCMR-15 (M-LOK® Compatible* Modular Rail), Expo Arms Free Float AR-15 Handguard - M-LOK - 15", Geissele Automatics 10.5" Super Modular Rail MK16 M-LOK, Geissele Automatics 13.5" Super Modular Rail MK16 M-LOK, Geissele Automatics 15" Super Modular Rail MK16 M-LOK, MAS Defense 12.62" NERO M-LOK FREE FLOAT, MAS Defense 15" NERO M-LOK FREE FLOAT, MAS Defense 9.87" NERO M-LOK FREE FLOAT, Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length), Midwest Industries Combat Rail One Piece Free Float Handguard, M-LOK™ (15")
- Frames
- Taurus TX22 Gen 2 frame
- Rail sections
- Magpul M-LOK® Aluminum Rail, 3 Slots, Magpul M-LOK® Aluminum Rail, 5 Slots, Magpul M-LOK® Aluminum Rail, 7 Slots, Magpul M-LOK® Aluminum Rail, 9 Slots, Magpul M-LOK® Polymer Rail, 11 Slots, Magpul M-LOK® Polymer Rail, 3 Slots, Magpul M-LOK® Polymer Rail, 5 Slots, Magpul M-LOK® Polymer Rail, 7 Slots, Magpul M-LOK® Polymer Rail, 9 Slots
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- AR15Discounts $98.96 Black Anodized Nov 21, 2026, stock not said
- AR15Discounts $98.96 Flat Dark Earth Anodized Nov 21, 2026, stock not said
- Rifle Supply $107.99 Black Anodized Nov 21, 2026, in stock that day
- Rifle Supply $107.99 Flat Dark Earth Anodized Nov 21, 2026, in stock that day
- Sportsman's Warehouse $109.99 Flat Dark Earth Anodized Nov 21, 2026, in stock that day
- Primary Arms $112.46 Black Anodized Nov 21, 2026, in stock that day
- Primary Arms $112.46 Flat Dark Earth Anodized Nov 21, 2026, in stock that day
- Rifle Supply $112.99 Black Anodized Nov 21, 2026, out of stock that day