Rail section
Magpul M-LOK® Aluminum Rail, 5 Slots
A five-slot Picatinny rail section machined from aluminium and hard anodized black, for any M-LOK hand guard or forend: two screws and two cammed T-nuts hold it in two M-LOK slots side by side, and its recoil lugs sit in the slots. Its ends are bevelled. Magpul: "M-LOK Aluminum Rail Sections allow the attachment of various 1913 Picatinny spec rail-mounted accessories such as lights, vertical grips, etc."

- Weight
- 0.42 oz ± 0.09 oz Provisionalworked out: The rail's own aluminium: the model's volume, 0.2658 cubic inches (pipeline/blender/magpul_mlok_aluminum_rail_section.py's manifest for this length, app/public/models/magpul-mlok-aluminum-rail-section-5-slot.json volume_in3, the screws apart), times std.density.aluminium (1.568 oz to the cubic inch: the alloy isn't stated, "Machined from milspec-anodized aluminum"): 0.417 oz. The ± is the height's (± 0.03 in over its length and the width under its head) and the alloy's 4%.
- Lowest price
- $18.53 at Primary Arms, read Nov 17, 2026
- Maker's number
- MAG581
- Colour
- Black (placeholder)
- Drawn as
- modelled
- Maker's page
- magpul.com
Added to “22RB .22 LR rifle”, a build on the start page, where the designer starts a new rail section.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Overall length (along the handguard)2.382 in ± 0.03 in 60.5 mmConflictPhoto: Magpul's studio photo, 1200 x 1200, from high over one end, no screws
Photo 2.331 in ± 0.01 in
Primary Arms, MAG581_00.jpg, 2200 x 1467: from above, square on, harvested
Scale: its own first and fifth grooves' centres (629.2 and 1479.0 px, each where its two walls cross half the teeth's grey, rows 540 to 910 within 1.5 px) as four standard pitches (std.picatinny.slot_pitch): 539.2 px to the inch, at the rail's top. Read by the base's outline end to end along the centre line (tools/trace.py, spec plan-measure: 1257 px), the arches' tips: at the top's scale, short by the base's perspective (adopt)
Published “Overall length: 2.5"”
Primary Arms, Magpul M-LOK Aluminum Rail Section - 5 Slot (MAG581), a seller, read Oct 29, 2026 the page, harvested Oct 29, 2026
Published “The overall length of this rail is around 2-3/5".”
Midwest Gun Works, Magpul Aluminum M-LOK Rail Section, 5 Slots (MAG581), a seller, read Oct 29, 2026 the page, harvested Oct 29, 2026
Photo 2.382 in ± 0.03 in used
Magpul's studio photo, 1200 x 1200, from high over one end, no screws, harvested
Scale: its two through holes (circles fitted to their white: 455.0, 668.5 and 760.5, 508.1 px), four standard pitches apart at the base's plane: 218.9 px to the inch along the line through them. Read by the base's outline along that line: 521.4 px. The same studio's photos of the seven- and nine-slot lengths read their lengths this way within 0.1% of Primary Arms' square views of them at their holes' scale; the three-slot's, its holes only 166 px apart, 2% long: the ±
The base's length at the scale of the holes in the base's own plane. Primary Arms' photo from above (plan) has its screws in and no hole to see: it is scaled by its grooves at the rail's top, 0.24 in nearer the lens than the base whose tips the outline's ends are, and reads short (the seven-slot's photo from the same seller has its through holes 1.8% inside its grooves; with that, 2.331 is 2.37). Magpul's figure is a maximum (max_length); Primary Arms' 2.5 repeats it; Midwest Gun Works' "around 2-3/5" is a round figure over it. Its end blocks then match the three-, seven- and nine-slot's (0.39 to 0.40 in) as read square on their bases.
plan and pa differ by 0.169 in beyond what each states it is good to.
plan and mgw differ by 0.269 in beyond what each states it is good to.
plan and magpul-oblique differ by 0.051 in beyond what each states it is good to.
pa and magpul-oblique differ by 0.118 in beyond what each states it is good to.
mgw and magpul-oblique differ by 0.218 in beyond what each states it is good to.
The base's length, tip to tip of its arched ends. The rail's top is shorter by the two end bevels (end_bevel_run).
Maximum overall length, as Magpul states it2.5 in 63.5 mmConfirmedPublished: Magpul, M-LOK Aluminum Rail Sections (GIS sheet, MAG580-MAG583_M-LOK_Aluminum_Rail_Sections_GIS_01.pdf), the maker, read Oct 29, 2026
Published “MAG581 - 5 Slots, max overall length of 2.5”” used
Magpul, M-LOK Aluminum Rail Sections (GIS sheet, MAG580-MAG583_M-LOK_Aluminum_Rail_Sections_GIS_01.pdf), the maker, read Oct 29, 2026 the page, harvested Oct 29, 2026
A bound, not the length: the test holds the length under it.
Height (its rail's top above the handguard's face it sits on)0.24 in ± 0.03 in 6.1 mmProvisionalPhoto: Midwest Gun Works, MAG581.jpg, 1500 x 1500: from above its near side, the hardware beside it
Photo 0.24 in ± 0.03 in used
Midwest Gun Works, MAG581.jpg, 1500 x 1500: from above its near side, the hardware beside it, harvested
Scale: an orthographic camera fitted to the rail's own teeth: along it, the standard's pitch on the near top edge (tooth to tooth 206.5 px, three pitches, on the line through (60, 920) at 11.0 degrees); across it, a tooth's top flat (the standard's .656, 297 px from its near corner (467, 985) to its far one (585, 712)); upright, from the two by the rotation's orthogonality (549 to 554 px to the inch, the up axis 62.7 to 67.5 px across and 344 to 351 down to the inch). Checked: the upper 45 degree face of a tooth, which the camera puts 68.7 to 69.4 px deep across the edge, reads 70.2 (column 515: 991.5 to 1063). Read by column 515 through a tooth: the top flat's near edge at 991.5 px, the bevel's band to 1063, the side to the background at 1093.5: 100.1 px across the edge's direction from the flat's near edge to the base's near edge. Through the camera that is 0.24 in of height with the band's foot taken for the base's near edge at the lower gauge line's width (.748); 0.21 if 0.79 across (the plan's reading at the grooves) and 0.18 if as wide as the head: the ± covers the first two. With the base 0.60 across (neck_width, read from below on the three- and nine-slot) and the head's lower faces carried on at 45 degrees down to it, the base's edge doesn't show from this camera, and the band's foot (a sharp edge against the white, 45 to 253 in 2 px) would be something else: a face this section doesn't have, or the part's shadow on the ground. The neck's foot that the undersides and the 45 degree faces give, 0.228 in under the top, is inside the ±
The rail's top above the base's underside, which bears on the hand guard's face (the recoil lugs under it go into the slots and aren't counted). Read on one photo, through a camera fitted to the part's own teeth, whose fit holds a second feature of them to 1 to 2 percent.
Width (side to side, at its widest)0.835 in ± 0.005 in 21.2 mmConfirmedWorked out: {std.picatinny.top_width}
Worked out 0.835 in ± 0.005 in used
{std.picatinny.top_width}, harvested
The head's widest is the standard's: Magpul, "various 1913 Picatinny spec rail-mounted accessories".
Photo 0.825 in ± 0.01 in
Primary Arms, from above, harvested
Scale: its grooves at the standard's pitch, as for length. Read by the outline across at its teeth: rows 505 to 949 (445 px; tools/trace.py reports 0.825)
A black edge on white reads a few pixels thin: 0.01 in under the standard's .835 -.005 here, as the teeth's own blur.
The standard's head; the photo from above reads it within its ±.
Nothing of it is wider than the head: the outline from above is the teeth's widest along both sides, and 0.02 in inside it at each groove.
Width of the base's flat face (the body's foot, on the hand guard's face)0.602 in ± 0.01 in 15.3 mmProvisionalWorked out: ({magpul-mlok-aluminum-rail-section-3-slot.neck_width} + {magpul-mlok-aluminum-rail-section-9-slot.neck_width}) / 2
Worked out 0.602 in ± 0.01 in used
({magpul-mlok-aluminum-rail-section-3-slot.neck_width} + {magpul-mlok-aluminum-rail-section-9-slot.neck_width}) / 2, harvested
The section under the head: the head's lower 45 degree faces carried on past the lower gauge line until they are this wide (0.227 in under the rail's top), and upright from there to the base, as the clamps' hooks need room under the head (rail-sections.test.ts) and as the photos of the underside show the base: narrower than the head by 0.11 in each side. Until 2026-10-29 the body was drawn upright at the lower gauge line's width (.748), an assumption, and three clamps' hooks stood in it. Midwest Gun Works' photos from above show a dark band 30 px deep under the head's widest on the near side, which a body undercut so far shows only as its shadow on the white ground: said in height's note.
Rail slots5ConfirmedPublished: Magpul, M-LOK® Aluminum Rail, 5 Slots (MAG581), the maker, read Oct 29, 2026
Published “M-LOK® Aluminum Rail, 5 Slots” used
Magpul, M-LOK® Aluminum Rail, 5 Slots (MAG581), the maker, read Oct 29, 2026 the page, harvested Oct 29, 2026
Published “5 slots of M1913 Picatinny rail”
Primary Arms, Magpul M-LOK Aluminum Rail Section - 5 Slot (MAG581), a seller, read Oct 29, 2026 the page, harvested Oct 29, 2026
Magpul's name for it; counted on the photo from above too (five grooves, four teeth between them and an end block at each end).
Rear rail slot's centre ahead of the part's rear end0.403 in ± 0.015 in 10.2 mmCorroboratedPhoto: Magpul's studio photo, from high over one end
Photo 0.403 in ± 0.015 in used
Magpul's studio photo, from high over one end, harvested
Scale: its through holes four standard pitches apart, at the base's plane, as for length. Read by the base's tip to the near hole along the line through the holes: 0.4033 in; the far end 0.4022
Photo 0.381 in ± 0.01 in
Primary Arms' MAG581 from above, 2200 x 1467, on white, harvested
Scale: its first and fifth grooves four standard pitches apart (539.2 px/in), at the rail's top. Read by −x_min of the traced outline (tools/trace.py): the base's rear tip behind the first groove's centre. The tip is 0.24 in further from the lens than the groove and stands in toward the picture's centre by about 10 px at the seven-slot photo's perspective: 0.400 with that
Read at the scale of the holes in the base's own plane, as the three-, seven- and nine-slot's end blocks are (0.395 to 0.40 in); Primary Arms' photo from above reads the tip at the top's scale, 0.02 short.
The end bevel's run: from the base's tip in to the bevel's top edge (along the part)0.122 in ± 0.015 in 3.1 mmCorroboratedPhoto: Primary Arms, from above
Photo 0.122 in ± 0.015 in used
Primary Arms, from above, harvested
Scale: its grooves at the standard's pitch, as for length. Read by on the centre line at the rear end, the base's tip (424 px) to the bevel's top edge, an arch concentric with the base's where the bevel's lighter grey gives way to the flat's (490 px): 66 px
Photo 0.13 in ± 0.02 in
Magpul, on a hand guard's side face, square on, harvested
Scale: its own two screws, four rail pitches apart (237 px). Read by its lit top, which ends at the bevel's top edge against the dark hand guard, reaches 0.64 of a pitch past each screw (37.7 px); the base reaches 0.966 of a pitch past it in the plan view: 0.33 of a pitch
The square view from above; the installed photo agrees within the two readings' ±.
Magpul: "beveled ends to reduce snagging". The bevel runs round the arched end at one width (its top edge is an arch inside the base's), from the base up to the rail's top: about 63 degrees from the base at this height.
Screws (and T-nuts) it is held by2CorroboratedPublished: Midwest Gun Works, Magpul Aluminum M-LOK Rail Section, 5 Slots (MAG581), a seller, read Oct 29, 2026
Published “Included with this premium piece are 2 cammed T-nuts and 2 recoil/impact mitigation lugs” used
Midwest Gun Works, Magpul Aluminum M-LOK Rail Section, 5 Slots (MAG581), a seller, read Oct 29, 2026 the page, harvested Oct 29, 2026
Photo 2 count
a photo on file, harvested
Scale: none: a count. Read by two T-nuts and two button-head screws beside it in Midwest Gun Works' photo; two counterbores, each with its screw, in the photo from above
The seller's sentence, counted on two photos.
Rail pitches from one screw to the next4ProvisionalPhoto: Primary Arms, from above
Photo 4 count used
Primary Arms, from above, harvested
Scale: its grooves at the standard's pitch, as for length. Read by the counterbores' circles fitted to their dark discs (centres 629.0 and 1480 px) stand on the first and the fifth grooves' centres (629.2 and 1479.0): four pitches, 1.575 in, which is the M-LOK slot pitch (40 mm, 1.5748 in) to 0.01%
The first screw stands in the first groove's floor, on its centre (rail_slot0_x).
M-LOK slots its T-nuts span2CorroboratedWorked out: {.screw_count}
Worked out 2 count used
{.screw_count}, harvested
Its seat on the M-LOK face: the centre of the M-LOK slot its rear T-nut is in, ahead of its rear end0.797 in ± 0.012 in 20.2 mmCorroboratedWorked out: {.rail_slot0_x} + {std.mlok.interval} / 2
Worked out 0.797 in ± 0.012 in used
{.rail_slot0_x} + {std.mlok.interval} / 2, harvested
Its two T-nuts are one M-LOK slot pitch apart (the screws over the first and the fifth grooves): each in the rear half of its slot. Magpul's photo of it on a hand guard's side face (4a11af353bb8) has its screws over the face's slots' centres, half an interval ahead of this seat: which half a nut is in isn't published, and the app's places, half a slot apart, are the same either way.
Reach inside the handguard (below the mounting face, tightened)No value yetMissingNo source yet
Not published: Magpul's M-LOK tips sheet sets the nut's top level with the recoil lug's bottom edge ("with the highest edge of the T-Nut even with the bottom edge of the recoil lug") and gives neither's size.
The screws' counterbores, across0.37 in ± 0.015 in 9.4 mmProvisionalPhoto: Primary Arms, from above
Photo 0.37 in ± 0.015 in used
Primary Arms, from above, harvested
Scale: its grooves at the standard's pitch, as for length. Read by the rear counterbore across, on the rows of its centre: 530 to 730 px (200 px; its dark disc's box 202 px). A circle fitted to the dark disc reads 96.8 px of radius (0.359 in), pulled in where the screw's lit rim breaks the disc
Each cuts the end block and the first tooth either side of its groove (both photos).
The screws' button heads, across0.21 in ± 0.04 in 5.3 mmProvisionalPhoto: Primary Arms, from above
Photo 0.21 in ± 0.04 in used
Primary Arms, from above, harvested
Scale: its grooves at the standard's pitch, as for length. Read by the dome of the head down in the rear counterbore: its lit rim round the hex socket 0.16 to 0.25 in across (87 to 135 px), its edge lost against the counterbore's dark wall; the ± covers both
How far below the rail's top the screws' heads seat (the counterbore's floor)0.2 in ± 0.03 in 5.1 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows the counterbore's floor in profile. The heads are down in the counterbores below the grooves' floors in every photo with the screws in; their seat is put 0.04 in above the base.
Worked out 0.2 in ± 0.03 in used
An assumption for the drawing, not a reading: no view on file shows the counterbore's floor in profile. The heads are down in the counterbores below the grooves' floors in every photo with the screws in; their seat is put 0.04 in above the base., harvested
The screws' button heads, high0.08 in ± 0.02 in 2 mmProvisionalWorked out: An assumption for the drawing, not a reading: Midwest Gun Works' photo has the two screws lying on their sides beside it but at a slant no camera has been fitted to; a button head about a third as high as it is wide.
Worked out 0.08 in ± 0.02 in used
An assumption for the drawing, not a reading: Midwest Gun Works' photo has the two screws lying on their sides beside it but at a slant no camera has been fitted to; a button head about a third as high as it is wide., harvested
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
M-LOK
- Uppers
- Nordic Components 22RB .22 LR upper, 16" (fit unchecked), Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12" (fit unchecked), Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16" (fit unchecked)
- Handguards
- Aero Precision AR15 10.3" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 12.7" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 15" Enhanced M-LOK Handguard, Gen 2 (fit unchecked), Aero Precision AR15 15" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 15" S-ONE M-LOK Handguard (fit unchecked), Aero Precision AR15 16.6" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 7.3" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 9.3" R-ONE M-LOK handguard (fit unchecked), BCM MCMR-10 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM MCMR-13 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM MCMR-15 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM PMCR (Polymer M-LOK® Compatible Rail)* Carbine Length-BLACK (fit unchecked), BCM PMCR (Polymer M-LOK® Compatible Rail)* Mid Length-BLACK (fit unchecked), Expo Arms Free Float AR-15 Handguard - M-LOK - 15" (fit unchecked), Geissele Automatics 10.5" Super Modular Rail MK16 M-LOK (fit unchecked), Geissele Automatics 13.5" Super Modular Rail MK16 M-LOK (fit unchecked), Geissele Automatics 15" Super Modular Rail MK16 M-LOK (fit unchecked), Magpul MOE SL® Hand Guard, Carbine-Length – AR15/M4 (fit unchecked), Magpul MOE SL® Hand Guard, Mid-Length – AR15/M4 (fit unchecked), Magpul MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4 (fit unchecked), Magpul MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4 (fit unchecked), MAS Defense 12.62" NERO M-LOK FREE FLOAT (fit unchecked), MAS Defense 15" NERO M-LOK FREE FLOAT (fit unchecked), MAS Defense 9.87" NERO M-LOK FREE FLOAT (fit unchecked), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine) (fit unchecked), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length) (fit unchecked), Midwest Industries Combat Rail One Piece Free Float Handguard, M-LOK™ (15") (fit unchecked)
- Adapter plates
- Magpul M-LOK Hand Stop MOE Adapter (fit unchecked)
Picatinny rail (MIL-STD-1913)
- Red dot mounts
- Aimpoint Duty RDS One-piece TNP Mount, 30 mm, Aimpoint LRP (Lever Release Picatinny) Mount with 39 mm Spacer, for Micro, Aimpoint One-piece Torsion Nut Mount and Spacer, 39 mm, Geissele Super Precision T1 Mount - 1.93" Height, Geissele Super Precision T1 Mount - Absolute Co-Witness, Geissele Super Precision T1 Mount - Lower 1/3 Co-Witness, Holosun 1.63 in lower 1/3 co-witness pedestal mount (HS-MOUNT-AR-RISER-ARO), Midwest Industries MK2 QD T2 Aimpoint Mount, Low, Midwest Industries MK2 QD T2 Aimpoint Mount, Lower 1/3 Cowitness, Midwest Industries MK2 QD T2 Aimpoint Mount, NV 2.26 in Height, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – 1.93″ HEIGHT, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – LOWER 1/3 (39MM HEIGHT), Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.42 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.57 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.93 in, Scalarworks LEAP/02 Aimpoint Micro T-2 quick-detach mount, 2.26 in, SIG Sauer M1913 I-BEAM Mount, 1.41 in absolute co-witness, SIG Sauer See-Through Riser Mount, 1.41 in absolute co-witness, Unity Tactical FAST Micro Mount, 2.26 in optical centerline
- Optics
- Aimpoint Patrol Rifle Optic (PRO) Red Dot Reflex Sight - QRP2 Mount, EOTECH HWS EXPS3 holographic weapon sight, 1-Dot Speed Ring, Holosun HS510C Open Reflex MRS Solar QD Mount
- Lights
- Olight Baldr S BL, Streamlight ProTac Rail Mount HL-X, SureFire Mini Scout Light Pro, SureFire Scout Light Pro Dual Fuel
- Backup sights
- Daniel Defense A1.5 Fixed Rear Sight, Daniel Defense Rail Mounted Fixed Front Sight, Magpul MBUS 3 Sight – Front, Magpul MBUS 3 Sight – Rear, Magpul MBUS Pro Sight – Front, Magpul MBUS Pro Sight – Rear
- Magnifiers
- EOTECH G33 Magnifier, STS Mount, EOTECH G45 Magnifier, STS Mount, Holosun HM3X 3× magnifier with flip mount
- Scope mounts
- Primary Arms Deluxe AR-15 Scope Mount - 30mm, Primary Arms SLx Cantilever 30mm Mount - 1.5", Reptilia AUS™ MOUNT - 30MM DIAMETER - 39MM HEIGHT, Scalarworks LEAP/08 quick-detach scope mount, 30 mm, 1.57 in, SIG SAUER ALPHA-MSR scope mount, 30 mm, Vortex Sport Cantilever 30mm Mount
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Primary Arms $18.53 Nov 17, 2026, in stock that day
- Midwest Gun Works $19.90 Nov 21, 2026, in stock that day
- Magpul $22.95 Nov 21, 2026, stock not said