Handguard
Magpul MOE SL® Hand Guard, Carbine-Length – AR15/M4
Magpul's slim polymer drop-in hand guard for a carbine-length gas system and an A2 front sight, in two halves: "Replaces standard AR15/M4 hand guards on carbine-length gas systems"; "Narrow cross section reduces weight and bulk"; "M-LOK slots at the two, six, and ten o'clock positions"; "The integral, riveted aluminum heat shield, combined with the front lower lip and side extensions, shields the support hand from a hot gas block"; "Front lip and long side extensions shields hand from hot sight assembly"; "Made in the USA" (Magpul). It goes on the rifle's own barrel nut and delta ring and the round cap behind its A2 front sight base: no free-float nut of its own.

- Weight
- 6.7 oz Confirmedpublished: Magpul, MOE SL® Hand Guard, Carbine-Length – AR15/M4, Model MAG538: Technical Specifications, the maker, read Oct 28, 2026
- Lowest price
- $31.13 at KYGUNCO, read Nov 21, 2026 (Stealth Gray)
- Maker's number
- MAG538
- Colours
- Black, Flat Dark Earth, Olive Drab Green, Stealth Gray
- Drawn as
- modelled
- Maker's page
- magpul.com
In “BCM 11.5 in carbine, suppressed”, a build on the start page, in place of its BCM MCMR-10 (M-LOK® Compatible* Modular Rail). The BCM Front Sight Base F - FSB (ID .750) - Milspec for Flat Top Uppers and the BCM G.I. Barrel Nut - AR15 and the BCM Delta Ring Assembly - AR15 and the BCM Handguard Cap Round - .750 AR15 go in with it: its maker says it needs them.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Length, maximum8.9 in 226.1 mmConflictPublished: Magpul, MOE SL® Hand Guard, Carbine-Length – AR15/M4, Model MAG538: Technical Specifications, the maker, read Oct 28, 2026
Published “Length, max 8.9 in.” used
Magpul, MOE SL® Hand Guard, Carbine-Length – AR15/M4, Model MAG538: Technical Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Published “Handguard Length 8.9”
Primary Arms, Magpul MOE SL Drop In AR-15 Handguard - M-LOK - Carbine Length - Grey (MAG538-GRY), a seller, read Oct 28, 2026 the page, harvested Oct 28, 2026
Photo 9.06 in ± 0.08 in
Magpul's mag538-fde_04: the Flat Dark Earth hand guard on a rifle, the rifle's right side seen level, 1200 x 1200, harvested
Scale: its three M-LOK slots, centres 686.5, 739.5 and 792.5 px: 53.0 px for the standard's 40 mm (std.mlok.slot_pitch), 33.65 px/in. Read by the outline at saturation > 0.15 from its rear (the tongues over the delta ring, column 607) to the side extensions' front tip (912): 305 px; ± 2 px at each end
The maker's figure; the photo, scaled by the standard's M-LOK pitch and by nothing of the part, reads 1.8% more, two pixels at each end of a 305 px outline.
magpul and photo differ by 0.16 in beyond what each states it is good to.
primary-arms and photo differ by 0.16 in beyond what each states it is good to.
From the rear end of the tongues that reach back over the delta ring to the tip of the side extensions, which wrap the front sight base ("Front lip and long side extensions shields hand from hot sight assembly").
Length, mounting (from its rear flange's end on the delta ring's lip to its front flange's end in the cap)6.6 in 167.6 mmConfirmedPublished: Magpul, MOE SL® Hand Guard, Carbine-Length – AR15/M4, Model MAG538: Technical Specifications, the maker, read Oct 28, 2026
Published “Length, mounting: 6.6 in.” used
Magpul, MOE SL® Hand Guard, Carbine-Length – AR15/M4, Model MAG538: Technical Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Magpul says no more than the figure; read as on its MOE M-LOK carbine (MAG424, the same 6.6 in on its page): what the rifle's delta ring and round cap hold the hand guard between. The front sight base's rear in the FDE photo (its tower's front leg at column 905, less the base's 1.804 in, bcm-front-sight-base-f-750.length) stands 6.49 in ahead of the bearing face read there: the flange's end goes 0.1 past the cap's floor, which the ring's spring takes up.
Width1.8 in ± 0.05 in 45.7 mmConfirmedPublished: Magpul, MOE SL® Hand Guard, Carbine-Length – AR15/M4, Model MAG538: Technical Specifications, the maker, read Oct 28, 2026
Published “Width 1.8 in.” used
Magpul, MOE SL® Hand Guard, Carbine-Length – AR15/M4, Model MAG538: Technical Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Published “1/3" NARROWER PROFILE THAN ORIGINAL MOE (1.8" RATHER THAN 2.2")”
Magpul, MOE SL® Hand Guard, Carbine-Length – AR15/M4, Model MAG538: Technical Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Photo 1.73 in ± 0.05 in
Magpul's feature 03 for MAG538: the black hand guard alone from above, 700 x 525, harvested
Scale: its side M-LOK slots seen edge-on along each edge, 100.0 px apart for the standard's 40 mm: 63.5 px/in at the side faces. Read by the body's silhouette across, rows 215 to 324 at column 300: 110 px; its sides are further from a lens above than its top, so it reads narrow
The maker's figure, said twice on its page. The view from above, scaled at the side faces' depth, reads 4% less, as a lens close above it would.
Height2.32 in ± 0.06 in 58.9 mmCorroboratedPhoto: Magpul's mag538-fde_04: the FDE hand guard on a rifle, its right side seen level
Published “Height: 2.4 in.”
Magpul, MOE SL® Hand Guard, Carbine-Length – AR15/M4, Model MAG538: Technical Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Photo 2.32 in ± 0.06 in used
Magpul's mag538-fde_04: the FDE hand guard on a rifle, its right side seen level, harvested
Scale: its M-LOK slots at the standard's pitch: 33.65 px/in. Read by the body's top (row 534) to its bottom (612) clear of the front lip, columns 640 to 830: 78 px; ± 1.5 px each edge
The model is drawn from the traced outline, at the photo's height. Magpul's 2.4 is 3% more; what it measures over isn't said (the front lip reaches lower). The mid-length's own photo reads 2.32 too, at twice this one's resolution.
Inside diameterNo value yetMissingNo source yet
Magpul gives none. The model's inside is its outside less the wall (wall), which no view gives either.
Its rear flange's end (bearing on the delta ring's lip) ahead of the receiver's front face0.336 in ± 0.015 in 8.5 mmProvisionalWorked out: {std.ar15.slip_ring_front_x}
Worked out 0.336 in ± 0.015 in used
{std.ar15.slip_ring_front_x}, harvested
Where the standard's delta ring holds it (std.ar15.slip_ring_front_x, from the Army's drawings): its rear flanges in the ring's skirt, against the lip. Its instruction sheet: "When both halves are in place, make sure your delta ring is securing BOTH upper and lower rear flanges of the Hand Guards".
The window in each side of its rear end, where the delta ring shows: from the tongues' rear end to the window's front edge0.68 in ± 0.06 in 17.3 mmProvisionalPhoto: Magpul's mag538-fde_04: the FDE hand guard on a rifle, its right side seen level
Photo 0.68 in ± 0.06 in used
Magpul's mag538-fde_04: the FDE hand guard on a rifle, its right side seen level, harvested
Scale: its M-LOK slots: 33.65 px/in. Read by the tongues' rear edge (column 607) to the window's front edge, where the black ring ends and the body's side begins (630): 23 px; ± 2 px
The ring fills the window in every photo of it on a rifle: its front edge is where the ring's front end is.
How far the tongues reach back over the delta ring behind its rear flange's end0.56 in ± 0.06 in 14.2 mmProvisionalWorked out: {.window_length} - {std.ar15.slip_ring_skirt_length}
Worked out 0.56 in ± 0.06 in used
{.window_length} - {std.ar15.slip_ring_skirt_length}, harvested
The window's front edge is the ring's front end, which stands the ring's skirt ahead of the lip the flanges bear on (std.ar15.slip_ring_skirt_length).
The tongues' rear end (where the side outline begins), from its rear flange's end-0.56 in ± 0.06 in -14.2 mmProvisionalWorked out: 0in - {.tongue_reach}
Worked out -0.56 in ± 0.06 in used
0in - {.tongue_reach}, harvested
Its top above the bore axis1.16 in ± 0.04 in 29.5 mmProvisionalPhoto: Magpul's mag538-fde_04: the FDE hand guard on a rifle, its right side seen level
Photo 1.16 in ± 0.04 in used
Magpul's mag538-fde_04: the FDE hand guard on a rifle, its right side seen level, harvested
Scale: its M-LOK slots: 33.65 px/in. Read by the barrel's axis ahead of the front sight base (its silhouette rows 563 to 583 at columns 1000 and 1060: centre 573; 0.62 in across, the barrel's 0.625) to the body's top (row 534): 39 px; ± 1.5 px
Its body's bottom (clear of the front lip) below the bore axis1.16 in ± 0.04 in 29.5 mmProvisionalPhoto: Magpul's mag538-fde_04: the FDE hand guard on a rifle, its right side seen level
Photo 1.16 in ± 0.04 in used
Magpul's mag538-fde_04: the FDE hand guard on a rifle, its right side seen level, harvested
Scale: its M-LOK slots: 33.65 px/in. Read by the barrel's axis (row 573) to the body's bottom (row 612, columns 640 to 830): 39 px; ± 1.5 px
The seam between its two halves, on the sides, above the bore axis (negative below)-0.09 in ± 0.03 in -2.3 mmProvisionalPhoto: Magpul's mag538-fde_04: the FDE hand guard on a rifle, its right side seen level
Photo -0.09 in ± 0.03 in used
Magpul's mag538-fde_04: the FDE hand guard on a rifle, its right side seen level, harvested
Scale: its M-LOK slots: 33.65 px/in. Read by the dark line along its side (luminance 120 at row 576, between 139 above and 126 below, column 700), 3 px under the axis; ± 1 px
The room inside its M-LOK faces before what runs through it (how far an accessory's nuts may reach in)No value yetMissingNo source yet
Depends on the barrel, the gas tube and the heat shield, and on the wall, which no view gives: no figure, so the check reads as unmade.
M-LOK slots in each upper side face (the two and ten o'clock rows)3ProvisionalPhoto: Magpul's mag538-fde_04, the FDE on a rifle, its right side
Photo 3 count used
Magpul's mag538-fde_04, the FDE on a rifle, its right side, harvested
Scale: none: a count. Read by three slots in the right side's row; three along each edge from above (11a885bc3699), along the left from below (d4a119f9380f) and on Primary Arms' gray (200bf0744ee8); the instruction sheet draws three on the carbine
The side rows' rearmost M-LOK slot (its centre), from its rear flange's end1.8 in ± 0.07 in 45.7 mmProvisionalPhoto: Magpul's mag538-fde_04, the FDE on a rifle, its right side seen level
Photo 1.8 in ± 0.07 in used
Magpul's mag538-fde_04, the FDE on a rifle, its right side seen level, harvested
Scale: its M-LOK slots: 33.65 px/in. Read by the rearmost slot's centre (column 686.5, between its edges at 665 and 708 at luminance 110) less the tongues' rear edge (607): 79.5 px = 2.36 in, less the tongues' reach (tongue_reach, 0.56); ± 2 px
The side rows' slot centres above the bore axis0.46 in ± 0.03 in 11.7 mmProvisionalPhoto: Magpul's mag538-fde_04, the FDE on a rifle, its right side seen level
Photo 0.46 in ± 0.03 in used
Magpul's mag538-fde_04, the FDE on a rifle, its right side seen level, harvested
Scale: its M-LOK slots: 33.65 px/in. Read by each slot's edges down its middle column (rows 553 to 562 at columns 680 and 740): centre 557.5, 15.5 px over the axis (row 573); ± 1 px
The side M-LOK faces' outward direction about the bore axis, from straight up (degrees)70° ± 7°ConflictPhoto: Magpul's feature 03: the black hand guard from above, 700 x 525) and 94b9fe2cb318 (the FDE on a rifle, its right side seen level
Published “M-LOK slots at the two, six, and ten o'clock positions for mounting MIL-STD-1913 Picatinny rails or other direct-attach M-LOK accessories”
Magpul, MOE SL® Hand Guard, Carbine-Length – AR15/M4, Model MAG538: Technical Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Published “Slots at the three, six, and nine o'clock positions for mounting direct-attach M-LOK accessories”
Midwest Gun Works, Magpul MOE SL AR15/M4 Carbine Length Handguard (MAG538-XX), a seller, read Oct 28, 2026 the page, harvested Oct 28, 2026
Photo 70 deg ± 7 deg used
Magpul's feature 03: the black hand guard from above, 700 x 525) and 94b9fe2cb318 (the FDE on a rifle, its right side seen level, harvested
Scale: from above, 63.5 px/in at the side faces; level, 33.65 px/in. Read by from above, the side slots show as slits 4 to 12 px across (rows 219 to 234 and 305 to 316: the lens off to one side), 8 px on average, against the slot's 7 mm (std.mlok.slot_width): cos ≈ 0.46, 63° ± 10; level from the side, each slot is 10 px tall, the full 7 mm (9.3 px): a face within 20° of upright. Both hold at 70
Magpul's "two ... ten o'clock" says which faces, and Midwest Gun Works says three and nine: the faces stand between, at the angle Magpul's own photos from above and from the side both allow.
magpul and midwest differ by 30° beyond what each states it is good to.
magpul and photo differ by 10° beyond what each states it is good to.
midwest and photo differ by 20° beyond what each states it is good to.
The side rows' slot centres out from the rifle's middle plane (the middle of each face's flat)0.814 in ± 0.04 in 20.7 mmProvisionalWorked out: {.width} / 2 - {.face_flat} / 2 * cos({.mlok_side_face_angle})
Worked out 0.814495 in ± 0.04 in used
{.width} / 2 - {.face_flat} / 2 * cos({.mlok_side_face_angle}), harvested
The face's flat runs up from the side at full width (its lower edge), leaning in at the face's angle, its middle where the photo has the slots' centres.
Where the side faces' normals through their slots' centres meet the rifle's middle plane, above the bore axis: the side M-LOK rows' axis0.164 in ± 0.06 in 4.2 mmProvisionalWorked out: {.mlok_side_slot_y} - {.mlok_side_slot_z} / tan({.mlok_side_face_angle})
Worked out 0.1635481 in ± 0.06 in used
{.mlok_side_slot_y} - {.mlok_side_slot_z} / tan({.mlok_side_face_angle}), harvested
The photos have the slots' centres higher on the faces than the foot of a line from the bore square to faces that lean as they do: the faces are angles about this axis instead (the anchor `mlok`), so that an accessory's nuts stand on the slots' centres.
The side M-LOK faces' distance from their axis (mlok_axis_y), along their outward direction0.867 in ± 0.05 in 22 mmProvisionalWorked out: {.mlok_side_slot_z} / sin({.mlok_side_face_angle})
Worked out 0.8667674 in ± 0.05 in used
{.mlok_side_slot_z} / sin({.mlok_side_face_angle}), harvested
From the axis to each slot's centre, square to its face.
M-LOK slots in the underside (six o'clock)4ProvisionalPhoto: Magpul's mag538-gry_02: the gray hand guard upside down, seen from below and its left, 1200 x 1200
Photo 4 count used
Magpul's mag538-gry_02: the gray hand guard upside down, seen from below and its left, 1200 x 1200, harvested
Scale: none: a count. Read by four openings along the underside's middle (row 532: columns 284 to 430, 466 to 610, 649 to 790 and 853 to 954), the last a short one with the shield showing in it, at the M-LOK pitch: three slots and a fourth
The underside's rearmost M-LOK slot (its centre), from its rear flange's end1.81 in ± 0.08 in 46 mmProvisionalPhoto: Magpul's mag538-gry_02: from below and its left
Photo 1.81 in ± 0.08 in used
Magpul's mag538-gry_02: from below and its left, harvested
Scale: the underside's own slots, 181 px a pitch (114.9 px/in), and the side's, 172.25 (109.4 px/in), each from the photo's middle column (600). Read by the underside's rearmost slot (column 357) stands 2.115 in behind the middle at its face's scale, the side's (367.5) 2.125 at its own: in line, 0.01 ahead of the side row's (mlok_side_slot0_x)
The underside's M-LOK face, its distance below the bore axis1.16 in ± 0.04 in 29.5 mmProvisionalWorked out: {.bottom_below_axis}
Worked out 1.16 in ± 0.04 in used
{.bottom_below_axis}, harvested
The heat shield's rearmost rivet (its head on the underside), from its rear flange's end1 in ± 0.08 in 25.4 mmProvisionalPhoto: Magpul's mag538-gry_02: from below
Photo 1 in ± 0.08 in used
Magpul's mag538-gry_02: from below, harvested
Scale: the underside's slots, 114.9 px/in. Read by a round head at column 265 in the underside's middle, 0.80 in behind the rearmost slot's centre
The heat shield's front rivet (its head on the underside), from its rear flange's end5.7 in ± 0.08 in 144.8 mmProvisionalPhoto: Magpul's mag538-gry_02: from below
Photo 5.7 in ± 0.08 in used
Magpul's mag538-gry_02: from below, harvested
Scale: the underside's slots, 114.9 px/in. Read by a round head at column 805, between the third and fourth openings: 3.90 in ahead of the rearmost slot's centre
A rivet head's diameter0.13 in ± 0.03 in 3.3 mmProvisionalPhoto: Magpul's mag538-gry_02: from below
Photo 0.13 in ± 0.03 in used
Magpul's mag538-gry_02: from below, harvested
Scale: the underside's slots, 114.9 px/in. Read by each head about 15 px across
How far a rivet head stands proud of the underside0.02 in ± 0.01 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the heads are seen from below only, never in profile.
Worked out 0.02 in ± 0.01 in used
An assumption for the drawing, not a reading: the heads are seen from below only, never in profile., harvested
The small slots in each row along its top (one row each side of the crown)8ProvisionalPhoto: Magpul's feature 03: the black hand guard from above
Photo 8 count used
Magpul's feature 03: the black hand guard from above, harvested
Scale: none: a count. Read by eight in each row (rows 242 and 300, columns 115 to 490); eight along the top on Primary Arms' gray (200bf0744ee8) and on Magpul's three-quarter view (8a8452bc4ff3)
The rearmost top slot's centre, from its rear flange's end0.29 in ± 0.08 in 7.4 mmProvisionalPhoto: Magpul's feature 03: the black hand guard from above
Photo 0.29 in ± 0.08 in used
Magpul's feature 03: the black hand guard from above, harvested
Scale: its side slots seen edge-on, 100.0 px apart for the standard's 40 mm: 63.5 px/in. Read by the rearmost top slot's centre (column 127.5) 96 px behind the side row's rearmost slot's (223.5): 1.51 in behind mlok_side_slot0_x
The top slots, centre to centre0.79 in ± 0.02 in 20.1 mmProvisionalPhoto: Magpul's feature 03, from above
Photo 0.79 in ± 0.02 in used
Magpul's feature 03, from above, harvested
Scale: 63.5 px/in. Read by the eight centres at 127.5 to 479 px: 50.2 px a pitch (the standard's 20 mm M-LOK interval is 0.787)
Each row of top slots, its centre line from the middle of the top0.45 in ± 0.04 in 11.4 mmProvisionalPhoto: Magpul's feature 03, from above
Photo 0.45 in ± 0.04 in used
Magpul's feature 03, from above, harvested
Scale: 63.5 px/in. Read by the rows at 242 and 300 px, the body's middle at 269.5 (its silhouette 215 to 324): 28.5 px each side
Each top slot's length along it0.37 in ± 0.03 in 9.4 mmProvisionalPhoto: Magpul's feature 03, from above
Photo 0.37 in ± 0.03 in used
Magpul's feature 03, from above, harvested
Scale: 63.5 px/in. Read by the dark runs along row 242, 23 to 25 px
Each top slot's width across0.12 in ± 0.03 in 3 mmProvisionalWorked out: An assumption for the drawing, not a reading: from above the carbine's top slots run into the shadows of the panels round them; about a third as wide as long, as they show on the Primary Arms gray (200bf0744ee8).
Worked out 0.12 in ± 0.03 in used
An assumption for the drawing, not a reading: from above the carbine's top slots run into the shadows of the panels round them; about a third as wide as long, as they show on the Primary Arms gray (200bf0744ee8)., harvested
The grooves along its crown, between the two rows of top slots8ProvisionalPhoto: Magpul's feature 03, from above
Photo 8 count used
Magpul's feature 03, from above, harvested
Scale: none: a count. Read by eight dark minima across column 330 between rows 262 and 286 (about 3.4 px apart)
The grooved strip's width across the crown0.38 in ± 0.04 in 9.7 mmProvisionalPhoto: Magpul's feature 03, from above
Photo 0.38 in ± 0.04 in used
Magpul's feature 03, from above, harvested
Scale: 63.5 px/in. Read by the first and the last minimum across column 330, rows 262 and 286: 24 px
Where the grooved strip ends at the front, from its rear flange's end6.85 in ± 0.1 in 174 mmProvisionalPhoto: Magpul's feature 03, from above
Photo 6.85 in ± 0.1 in used
Magpul's feature 03, from above, harvested
Scale: 63.5 px/in. Read by the dark strip along row 270 ends at column 544 (its rounded end), 5.05 in ahead of the side row's rearmost slot (223.5 px)
Each crown groove's depth0.015 in ± 0.01 in 0.4 mmProvisionalWorked out: An assumption for the drawing, not a reading: the grooves are seen from above only.
Worked out 0.015 in ± 0.01 in used
An assumption for the drawing, not a reading: the grooves are seen from above only., harvested
The upright ribs along each side of the lower half8ProvisionalPhoto: Magpul's mag538-fde_04, the FDE on a rifle, its right side
Photo 8 count used
Magpul's mag538-fde_04, the FDE on a rifle, its right side, harvested
Scale: none: a count. Read by eight lines down the lower half between the window and the front panel (row 593: columns 656.5, 682, 707, 733, 758, 783, 808.5, 834)
The rearmost rib, from its rear flange's end0.91 in ± 0.06 in 23.1 mmProvisionalPhoto: Magpul's mag538-fde_04, the FDE on a rifle, its right side seen level
Photo 0.91 in ± 0.06 in used
Magpul's mag538-fde_04, the FDE on a rifle, its right side seen level, harvested
Scale: 33.65 px/in. Read by column 656.5, 49.5 px ahead of the tongues' rear edge (607) = 1.47 in, less tongue_reach
The ribs, one to the next0.75 in ± 0.02 in 19 mmProvisionalPhoto: Magpul's mag538-fde_04, the FDE on a rifle, its right side seen level
Photo 0.75 in ± 0.02 in used
Magpul's mag538-fde_04, the FDE on a rifle, its right side seen level, harvested
Scale: 33.65 px/in. Read by seven gaps from 656.5 to 834 px: 25.2 px each; from below (d4a119f9380f) the small slots between them are 87.7 px apart, 0.76 to 0.80 in by which face's scale
Each rib's width0.06 in ± 0.02 in 1.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: each rib shows as a lit and a shaded line one or two pixels wide at 33.65 px/in (0.03 to 0.06), and a few pixels on the mid-length's closer photos.
Worked out 0.06 in ± 0.02 in used
An assumption for the drawing, not a reading: each rib shows as a lit and a shaded line one or two pixels wide at 33.65 px/in (0.03 to 0.06), and a few pixels on the mid-length's closer photos., harvested
How far each rib stands from the panels between them0.03 in ± 0.015 in 0.8 mmProvisionalWorked out: An assumption for the drawing, not a reading: the ribs cast short shadows in Magpul's close photos of the mid-length (a6cff9cf637f), never seen in profile.
Worked out 0.03 in ± 0.015 in used
An assumption for the drawing, not a reading: the ribs cast short shadows in Magpul's close photos of the mid-length (a6cff9cf637f), never seen in profile., harvested
The small slots in each row along the lower edges10ProvisionalPhoto: Magpul's mag538-gry_02: from below and its left
Photo 10 count used
Magpul's mag538-gry_02: from below and its left, harvested
Scale: none: a count. Read by ten along row 601 (columns 176 to 1004), between the ribs and on under the front panel
The rearmost lower-edge slot's centre, from its rear flange's end0.27 in ± 0.1 in 6.9 mmProvisionalPhoto: Magpul's mag538-gry_02: from below and its left
Photo 0.27 in ± 0.1 in used
Magpul's mag538-gry_02: from below and its left, harvested
Scale: between the side face's 109.4 and the underside's 114.9 px/in, 112. Read by column 196.5, 171 px behind the side row's rearmost slot (367.5): 1.53 in behind mlok_side_slot0_x
The lower-edge slots, centre to centre0.78 in ± 0.03 in 19.8 mmProvisionalPhoto: Magpul's mag538-gry_02: from below
Photo 0.78 in ± 0.03 in used
Magpul's mag538-gry_02: from below, harvested
Scale: 112 px/in. Read by ten centres from 196.5 to 985.5 px: 87.7 px a pitch
Each lower-edge slot's length0.36 in ± 0.03 in 9.1 mmProvisionalPhoto: Magpul's mag538-gry_02: from below
Photo 0.36 in ± 0.03 in used
Magpul's mag538-gry_02: from below, harvested
Scale: 112 px/in. Read by the dark runs along row 601: 38 to 42 px
Each lower-edge slot's width0.1 in ± 0.03 in 2.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the slots show about a quarter as wide as long from below, at an angle the photo doesn't give.
Worked out 0.1 in ± 0.03 in used
An assumption for the drawing, not a reading: the slots show about a quarter as wide as long from below, at an angle the photo doesn't give., harvested
How deep the top and lower-edge slots go (they are blind)0.06 in ± 0.03 in 1.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view shows one in section; they show their own colour inside, not the barrel.
Worked out 0.06 in ± 0.03 in used
An assumption for the drawing, not a reading: no view shows one in section; they show their own colour inside, not the barrel., harvested
Its polymer wall's thickness0.15 in ± 0.04 in 3.8 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows an end square on or a section. Taken so that the model comes near Magpul's 6.7 oz at the polymer's density on file (std.density.polymer) with its aluminium heat shield; what it still lacks is the inner ribs and bosses no view shows.
Worked out 0.15 in ± 0.04 in used
An assumption for the drawing, not a reading: no view on file shows an end square on or a section. Taken so that the model comes near Magpul's 6.7 oz at the polymer's density on file (std.density.polymer) with its aluminium heat shield; what it still lacks is the inner ribs and bosses no view shows., harvested
Its aluminium heat shield's thickness0.03 in ± 0.015 in 0.8 mmProvisionalWorked out: An assumption for the drawing, not a reading: the shield shows edge-on only in Magpul's feature 04 (d70407049a05), a bright sheet a few pixels thick at 700 px for the hand guard's half.
Worked out 0.03 in ± 0.015 in used
An assumption for the drawing, not a reading: the shield shows edge-on only in Magpul's feature 04 (d70407049a05), a bright sheet a few pixels thick at 700 px for the hand guard's half., harvested
The seam's groove along each side (its width and its depth)0.02 in ± 0.01 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the seam shows as a dark line one pixel wide at 33.65 px to the inch, its depth on no view.
Worked out 0.02 in ± 0.01 in used
An assumption for the drawing, not a reading: the seam shows as a dark line one pixel wide at 33.65 px to the inch, its depth on no view., harvested
Each upper side face's flat (where its M-LOK slots are), its height across the face0.5 in ± 0.1 in 12.7 mmProvisionalWorked out: An assumption for the drawing, not a reading: the slot's 7 mm and a margin each side, as Primary Arms' gray (200bf0744ee8) shows the face round its slots.
Worked out 0.5 in ± 0.1 in used
An assumption for the drawing, not a reading: the slot's 7 mm and a margin each side, as Primary Arms' gray (200bf0744ee8) shows the face round its slots., harvested
Its top's flat (the crown with its two rows of slots), half its width0.6 in ± 0.1 in 15.2 mmProvisionalWorked out: An assumption for the drawing, not a reading: no end view on file; from above, the two rows of top slots stand 0.45 either side of the middle, seen whole (not foreshortened), so the top is near flat that far out and a little more.
Worked out 0.6 in ± 0.1 in used
An assumption for the drawing, not a reading: no end view on file; from above, the two rows of top slots stand 0.45 either side of the middle, seen whole (not foreshortened), so the top is near flat that far out and a little more., harvested
Its underside's flat (where the six o'clock slots are), half its width0.42 in ± 0.1 in 10.7 mmProvisionalWorked out: An assumption for the drawing, not a reading: no end view; from below (d4a119f9380f) the underside's flat holds its M-LOK slots with a margin each side, rounding into the sides at the lower-edge slots.
Worked out 0.42 in ± 0.1 in used
An assumption for the drawing, not a reading: no end view; from below (d4a119f9380f) the underside's flat holds its M-LOK slots with a margin each side, rounding into the sides at the lower-edge slots., harvested
Where the side rounds under into the underside, above the bore axis (negative below)-0.78 in ± 0.1 in -19.8 mmProvisionalWorked out: An assumption for the drawing, not a reading: the lower-edge slots are on the round, seen from the side as notches along the bottom edge and from below as a row beside the underside's slots.
Worked out -0.78 in ± 0.1 in used
An assumption for the drawing, not a reading: the lower-edge slots are on the round, seen from the side as notches along the bottom edge and from below as a row beside the underside's slots., harvested
Its front flange (what goes into the round cap), outside diameter1.36 in ± 0.05 in 34.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: Magpul's instructions slide the flange "into the metal hand guard cap"; no view shows it. Taken inside the round cap on file (bcm-handguard-cap-round-750, its tabs at 3 and 9 o'clock to 0.690 from the axis).
Worked out 1.36 in ± 0.05 in used
An assumption for the drawing, not a reading: Magpul's instructions slide the flange "into the metal hand guard cap"; no view shows it. Taken inside the round cap on file (bcm-handguard-cap-round-750, its tabs at 3 and 9 o'clock to 0.690 from the axis)., harvested
Its front flange's length (into the cap)0.42 in ± 0.1 in 10.7 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view shows the flange from the side. Long enough that the front wall it stands from stays behind the round cap's rim with the flange home (the cap is 0.276 deep).
Worked out 0.42 in ± 0.1 in used
An assumption for the drawing, not a reading: no view shows the flange from the side. Long enough that the front wall it stands from stays behind the round cap's rim with the flange home (the cap is 0.276 deep)., harvested
Its rear flanges (what stands in the delta ring's skirt), outside diameter1.72 in ± 0.03 in 43.7 mmProvisionalWorked out: An assumption for the drawing, not a reading: the flanges stand in the delta ring's skirt (std.ar15.slip_ring_skirt_d, 1.750 inside) and show on no photo; taken 0.03 under the skirt.
Worked out 1.72 in ± 0.03 in used
An assumption for the drawing, not a reading: the flanges stand in the delta ring's skirt (std.ar15.slip_ring_skirt_d, 1.750 inside) and show on no photo; taken 0.03 under the skirt., harvested
The room between the tongues and the delta ring they reach back over0.02 in ± 0.02 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the tongues stand over the ring (std.ar15.slip_ring_od, 2.1) and their inside is seen on no photo.
Worked out 0.02 in ± 0.02 in used
An assumption for the drawing, not a reading: the tongues stand over the ring (std.ar15.slip_ring_od, 2.1) and their inside is seen on no photo., harvested
Its front wall (the inner face the front flange stands from), from its rear flange's end6.03 in ± 0.12 in 153.2 mmProvisionalWorked out: {.mounting_length} - {.front_flange_length} - {.wall}
Worked out 6.03 in ± 0.12 in used
{.mounting_length} - {.front_flange_length} - {.wall}, harvested
Ahead of the wall the shell runs on as its side extensions and its front lip, open over the top, round the cap and the front sight base ("Hand Guard will wrap around the front sight when mounted").
Its front panel's width (it stands out from the body round the cap and the front sight base)1.99 in ± 0.05 in 50.5 mmProvisionalPhoto: Magpul's feature 03: the black hand guard from above
Photo 1.99 in ± 0.05 in used
Magpul's feature 03: the black hand guard from above, harvested
Scale: the body's width beside it, Magpul's 1.8 in (width), at the same depth. Read by the front panel's silhouette across, rows 210 to 334 at columns 540 to 610: 125 px, against the body's 113 (rows 215 to 327 at column 450): 1.106 times Magpul's width
Where the front panel stands out from the body, from its rear flanges' end6.19 in ± 0.1 in 157.2 mmProvisionalPhoto: Magpul's feature 03: the black hand guard from above
Photo 6.19 in ± 0.1 in used
Magpul's feature 03: the black hand guard from above, harvested
Scale: its side slots seen edge-on: 63.5 px/in. Read by the silhouette's step out along row 211 at column 502, 4.39 in ahead of the side row's rearmost slot (223.5 px)
The room inside its front panel round the hand guard cap1.733 in ± 0.04 in 44 mmProvisionalWorked out: {bcm-handguard-cap-round-750.lip_od} + 2 * {.ring_clearance}
Worked out 1.7329 in ± 0.04 in used
{bcm-handguard-cap-round-750.lip_od} + 2 * {.ring_clearance}, harvested
The front panel wraps the round cap ("Hand Guard will wrap around the front sight when mounted"): its inside is the cap's own outside and a clearance (ring_clearance), the one round cap on file.
The round at the top of its front edge (where the side extensions' level top turns down the front), its length along0.12 in ± 0.06 in 3 mmProvisionalPhoto: Magpul's mag538-blk_04: the black hand guard on a rifle, its right side seen level; the same pose as the Flat Dark Earth one traced
Photo 0.12 in ± 0.06 in used
Magpul's mag538-blk_04: the black hand guard on a rifle, its right side seen level; the same pose as the Flat Dark Earth one traced, harvested
Scale: 33.65 px/in by its M-LOK slots (the FDE photo's pose). Read by the level top's edge ends and the round begins 4 px behind the front edge (by eye on a crop at 3 to 5 times; the front sight base's front leg stands just ahead of it)
The traced outline's corner here is the front sight's leg's, not the part's: the model draws this round instead (clean_nose in the script).
The same round's height down the front edge0.24 in ± 0.06 in 6.1 mmProvisionalPhoto: Magpul's mag538-blk_04: the black hand guard on a rifle, its right side seen level; the same pose as the Flat Dark Earth one traced
Photo 0.24 in ± 0.06 in used
Magpul's mag538-blk_04: the black hand guard on a rifle, its right side seen level; the same pose as the Flat Dark Earth one traced, harvested
Scale: 33.65 px/in by its M-LOK slots (the FDE photo's pose). Read by the front edge runs straight from 8 px under the level top (by eye on the same crop)
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Drop-in handguard's front in its cap
Handguard mount
Drop-in handguard's hold
- Delta rings
- BCM Delta Ring Assembly - AR15
Gas system length
M-LOK
- Hand stops
- BCM KAG (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK Hand Stop (fit unchecked), Magpul M-LOK Index Panel (fit unchecked)
- Vertical grips
- BCM Vertical Grip Mod 3 (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK MVG vertical grip (fit unchecked)
- Lights
- Cloud Defensive REIN (fit unchecked), Streamlight ProTac Rail Mount HL-X (fit unchecked), SureFire Mini Scout Light Pro (fit unchecked), SureFire Scout Light Pro Dual Fuel (fit unchecked)
- Rail sections
- Magpul M-LOK® Aluminum Rail, 3 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 5 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 7 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 9 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 11 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 3 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 5 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 7 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 9 Slots (fit unchecked)
- Adapter plates
- Magpul M-LOK Hand Stop MOE Adapter (fit unchecked)
- Sling mounts
- Magpul M-LOK QD Sling Mount (fit unchecked)
- Rail covers
- Magpul M-LOK Rail Cover Type 2 (fit unchecked)
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- KYGUNCO $31.13 Stealth Gray Nov 21, 2026, in stock that day
- Midwest Gun Works $37.95 Black Nov 21, 2026, in stock that day
- Midwest Gun Works $37.95 Flat Dark Earth Nov 21, 2026, in stock that day
- Midwest Gun Works $37.95 Olive Drab Green Nov 21, 2026, in stock that day
- Midwest Gun Works $37.95 Stealth Gray Nov 21, 2026, in stock that day
- Magpul $39.95 Black Nov 21, 2026, stock not said
- Magpul $39.95 Flat Dark Earth Nov 21, 2026, stock not said
- Magpul $39.95 Olive Drab Green Nov 21, 2026, stock not said
- Magpul $39.95 Stealth Gray Nov 21, 2026, stock not said
- Primary Arms $32.26 Stealth Gray Nov 1, 2026, out of stock that day