Handguard cap
BCM Handguard Cap Triangle - .750 AR15
BCM: "Handguard Cap for your AR15, M16, M4. Triangle are typically used on AR15 barrels with a mid length or rifle length gas system. For .750 Diameter Barrel". The cap behind the front sight base that holds the front of a drop-in handguard: the triangular one, for the M16A1's vertically split handguards and the drop-ins made to take it.

- Weight
- 0.31 oz ± 0.02 oz Provisionalworked out: (1.5 * ({.corner_r} * {.corner_r} * (120 - 2 * {.side_half_angle}) * 0.0174532925 + 2 * {.corner_circle_r} * {.corner_r} * sin(60 - {.side_half_angle}) + 2 * {.side_r} * {.side_r} * {.side_half_angle} * 0.0174532925 - 2 * {.side_centre_r} * {.side_r} * sin({.side_half_angle})) - 3 * ({.corner_r} * (120 - 2 * {.side_half_angle}) + 2 * {.side_r} * {.side_half_angle}) * 0.0174532925 * {.bend_r} + 3.14159265 * {.bend_r} * {.bend_r} - 0.785398163 * {.bore_d} * {.bore_d} - {.slot_w} * ({.slot_hi} - {.slot_lo} - {.slot_w}) - 0.785398163 * {.slot_w} * {.slot_w} + 1.57079633 * ({.bend_r} - {.sheet} / 2) * (3 * ({.corner_r} * (120 - 2 * {.side_half_angle}) + 2 * {.side_r} * {.side_half_angle}) * 0.0174532925 - 6.28318531 * {.bend_r} + 4 * ({.bend_r} - {.sheet} / 2)) + (3 * ({.corner_r} * (120 - 2 * {.side_half_angle}) + 2 * {.side_r} * {.side_half_angle}) * 0.0174532925 - 3.14159265 * {.sheet}) * ({.skirt_depth} + {.sheet} - {.bend_r}) + 3.14159265 * ({.bore_d} + {.sheet}) * {.collar}) * {.sheet} * {std.density.steel}
- Lowest price
- $3.00 at BCM, read Nov 21, 2026
- Maker's number
- Handguard-Cap-Triangle-.750
- Colour
- BCM handguard cap (triangle), manganese phosphate
- Drawn as
- modelled
- Maker's page
- bravocompanyusa.com
In “Drop-in 16 in, Stealth Gray on BCM's MK2 lower”, a build on the start page, in place of its BCM Handguard Cap Round - .750 AR15.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Bore (the journal it fits: .750 or .625)0.75 in ± 0.0005 in 19 mmConfirmedPublished: BCM, Handguard Cap Triangle - .750 AR15, the maker, read Oct 28, 2026
Published “For .750 Diameter Barrel” used
BCM, Handguard Cap Triangle - .750 AR15, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
The bore over the journal it fits0.003 in ± 0.0025 in 0.1 mmConfirmedStandard: US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)
Standard “.625 DIA +.005” used
US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice), from the site owner
The drawing's cap is bored ".625 DIA +.005" for a .625 journal: up to five thousandths over it. Taken for BCM's .750 cap as the same stamping practice (BCM states no bore but its journal); the middle of the band, its ± the band's half.
The bore's diameter0.752 in ± 0.003 in 19.1 mmConfirmedWorked out: {.journal_id} + {.bore_clearance}
Worked out 0.7525 in ± 0.003 in used
{.journal_id} + {.bore_clearance}, harvested
BCM's journal and the drawing's clearance over it.
The drawing's bore (the .625 cap's)0.627 in ± 0.0025 in 15.9 mmConfirmedStandard: US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)
Standard “.625 DIA +.005” used
US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice), from the site owner
The middle of .625 to .630.
Kept for the record of what the drawing is for: BCM's cap is the .750 one, bore_d.
The sheet's thickness0.025 in ± 0.001 in 0.6 mmConfirmedStandard: US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)
Standard “.025±.001” used
US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice), from the site owner
Section A-A: the face, the skirt and the collar are one sheet.
Depth along the bore0.328 in ± 0.005 in 8.3 mmConfirmedStandard: US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)
Standard “.328 REF” used
US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice), from the site owner
Section A-A, a reference dimension: .240 + .025 + .063.
From the skirt's open edge (where a handguard's front goes in) to the collar's front end (which bears on the front sight base): .240 to the face's inside, the sheet, and the collar.
The skirt's depth inside, from its open edge to the face's inside0.24 in ± 0.005 in 6.1 mmConfirmedStandard: US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)
Standard “.240” used
US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice), from the site owner
Section A-A: from the skirt's open edge to the face's rear (inner) surface.
The pocket a drop-in handguard's front flange goes into: from the rim's open edge forward to the back of the face.
The collar round the bore, ahead of the face0.058 in ± 0.005 in 1.5 mmConfirmedStandard: US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)
Standard “.063 -.010” used
US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice), from the site owner
Section A-A: from the face's front surface to the collar's end. The middle of .053 to .063.
The bore's edge is drawn forward, a short collar of the sheet: its front end is the cap's front, which bears on the front sight base's rear face. BCM's one 500 px photo of the face neither shows nor rules out its outside (the bore's wall reads deeper than the sheet: about 0.09 at its view's angle, which the collar's .088 is).
The three corners' radius (outside)0.287 in ± 0.005 in 7.3 mmConfirmedStandard: US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)
Standard “.287 R” used
US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice), from the site owner
The corners' centres from the bore axis0.625 in ± 0.005 in 15.9 mmConfirmedStandard: US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)
Standard “.625 REF TO ℄ OF .287 R” used
US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice), from the site owner
The three corners' centres on one circle about the bore, 120° apart: the top one over the bore (the gas tube's side), the two below at 30° under the horizontal (the drawing's .312 REF and .541 REF are this at 30°).
The three sides' radius (outside)1.626 in ± 0.005 in 41.3 mmConfirmedStandard: US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)
Standard “1.626 R, 3 PLACES” used
US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice), from the site owner
Each side is an arc tangent to the two corners beside it: "1.626 R, 3 PLACES TANGENT TO .287 RADII AND THROUGH POINTS DETERMINED BY 1.626 DIMENSIONS" (its centre is the opposite corner's outer extreme, .912 from the bore, to the drawing's figures).
The bore axis to the top corner's outside0.912 in ± 0.005 in 23.2 mmConfirmedStandard: US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)
Standard “.912” used
US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice), from the site owner
Section A-A.
corner_circle_r + corner_r (.625 + .287 = .912).
Width across1.656 in ± 0.005 in 42.1 mmConfirmedStandard: US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)
Standard “1.656” used
US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice), from the site owner
Across the two lower corners: 2 × (.541 + .287).
Height1.626 in ± 0.005 in 41.3 mmConfirmedStandard: US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)
Standard “1.626 3 PLACES” used
US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice), from the site owner
From the top corner to the bottom side, as from each corner to the side across from it.
The bend from the face to the skirt (outside)0.09 in ± 0.01 in 2.3 mmConfirmedStandard: US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)
Standard “.09 R” used
US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice), from the site owner
Section A-A, the leader on the bend's outside.
The gas tube's hole: its width0.187 in ± 0.002 in 4.7 mmConfirmedStandard: US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)
Standard “.187±.002” used
US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice), from the site owner
Its two ends "FULL RADIUS".
Windham Weaponry's triangular .750 cap: "punched with an oblong hole for the gas tube".
The gas tube's hole: its lower end above the bore axis0.513 in ± 0.005 in 13 mmConfirmedStandard: US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)
Standard “.513” used
US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice), from the site owner
The gas tube's hole: its upper end above the bore axis0.737 in ± 0.005 in 18.7 mmConfirmedStandard: US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice)
Standard “.737” used
US Army TDP drawing 8448564 (Cap, Handguard), sheet 1 of 1, rev B, scale 2/1, PDF page 111 (the M16's and M16A1's cap, for a .625 journal); user-supplied scan (Distribution Statement F, Colt proprietary notice), from the site owner
The side arcs' centres from the bore axis0.912 in ± 0.01 in 23.2 mmConfirmedWorked out: (sqrt(4 * ({.side_r} - {.corner_r}) * ({.side_r} - {.corner_r}) - 3 * {.corner_circle_r} * {.corner_circle_r}) - {.corner_circle_r}) / 2
Worked out 0.912 in ± 0.01 in used
(sqrt(4 * ({.side_r} - {.corner_r}) * ({.side_r} - {.corner_r}) - 3 * {.corner_circle_r} * {.corner_circle_r}) - {.corner_circle_r}) / 2, harvested
Where an arc of side_r tangent inside two corners of corner_r, on corner_circle_r 120° apart, has its centre: on the line through the third corner, q² + a q + a² = (side_r − corner_r)². The drawing's "THROUGH POINTS DETERMINED BY 1.626 DIMENSIONS" puts it at the opposite corner's outer extreme, apex_r: the two agree to a thousandth.
The half of each side arc, about its centre23.8° ± 0.2°ProvisionalWorked out: acos((corner_circle_r / 2 + side_centre_r) / (side_r − corner_r)) with the drawing's .625, .287 and 1.626: 23.843°. The ± is what each figure's ± .005 moves it by.
Worked out 23.84 deg ± 0.2 deg used
acos((corner_circle_r / 2 + side_centre_r) / (side_r − corner_r)) with the drawing's .625, .287 and 1.626: 23.843°. The ± is what each figure's ± .005 moves it by., harvested
From the side arc's centre, the angle between the line to the side's middle and the line to a corner's centre (where the arc meets that corner): cos β = (corner_circle_r / 2 + side_centre_r) / (side_r − corner_r). The ledger's expressions have no inverse cosine, so the figure is written here; app/tests/bcm-handguard-cap-triangle-750.test.ts works it out again from the four. Each corner's arc is then 120° − 2β. The weight's outline (its area and its length round) is taken over these six arcs.
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Drop-in handguard's front in its cap
- Handguards
- BCM PMCR (Polymer M-LOK® Compatible Rail)* Carbine Length-BLACK, BCM PMCR (Polymer M-LOK® Compatible Rail)* Mid Length-BLACK, Magpul MOE SL® Hand Guard, Carbine-Length – AR15/M4, Magpul MOE SL® Hand Guard, Mid-Length – AR15/M4, Magpul MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4, Magpul MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4, Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length)
Handguard cap seat
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- BCM $3.00 Nov 21, 2026, in stock that day