Handguard
Magpul MOE SL® Hand Guard, Mid-Length – AR15/M4
Magpul's slim polymer drop-in hand guard for a mid-length gas system and an A2 front sight, in two halves: "An upgrade to AR15/M4 firearms with mid-length gas systems"; "Narrow cross section reduces weight and bulk"; "M-LOK® slots at two, six, and ten o'clock for accessories"; "Internal aluminum heat shield, front lip and side extensions protect against high heat during firing"; "Front lip and long side extensions shields hand from hot sight assembly"; "Made in the USA" (Magpul). It goes on the rifle's own barrel nut and delta ring and the round cap behind its A2 front sight base: no free-float nut of its own.

- Weight
- 8.3 oz Confirmedpublished: Magpul, MOE SL® Hand Guard, Mid-Length – AR15/M4, Model MAG551: Technical Specifications, the maker, read Oct 28, 2026
- Lowest price
- $31.13 at KYGUNCO, read Nov 21, 2026 (Olive Drab Green)
- Maker's number
- MAG551
- Colours
- Black, Flat Dark Earth, Olive Drab Green, Stealth Gray
- Drawn as
- modelled
- Maker's page
- magpul.com
In “Aero 5.56 carbine”, a build on the start page, in place of its Aero Precision AR15 15" R-ONE M-LOK handguard. The BCM Front Sight Base F - FSB (ID .750) - Milspec for Flat Top Uppers and the BCM G.I. Barrel Nut - AR15 and the BCM Delta Ring Assembly - AR15 and the BCM Handguard Cap Round - .750 AR15 go in with it: its maker says it needs them.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Length, maximum10.9 in ± 0.05 in 276.9 mmConfirmedPublished: Magpul, MOE SL® Hand Guard, Mid-Length – AR15/M4, Model MAG551: Technical Specifications, the maker, read Oct 28, 2026
Published “Length, max 10.9 in.” used
Magpul, MOE SL® Hand Guard, Mid-Length – AR15/M4, Model MAG551: Technical Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Published “Handguard Length 10.9”
Primary Arms, Magpul MOE SL Drop In AR-15 Handguard - M-LOK - Mid-Length - FDE (MAG551-FDE), a seller, read Oct 28, 2026 the page, harvested Oct 28, 2026
Photo 10.86 in ± 0.04 in
Magpul's mag551-odg_03: the OD green hand guard on a rifle, the rifle's right side seen level, 1200 x 1200, harvested
Scale: its four M-LOK slots, centres 390.5, 503.5, 615.5 and 729.5 px: 113.0 px for the standard's 40 mm (std.mlok.slot_pitch), 71.75 px/in. Read by the outline from the tongues' rear over the delta ring (column 196) to the side extensions' front tip (975): 779 px; ± 1.5 px at each end
The maker's figure; the photo, scaled by the standard's M-LOK pitch and by nothing of the part, agrees within 0.04 in (0.4%).
From the rear end of the tongues that reach back over the delta ring to the tip of the side extensions, which wrap the front sight base ("Front lip and long side extensions shields hand from hot sight assembly").
Length, mounting (from its rear flanges' end on the delta ring's lip to its front flange's end in the cap)8.6 in ± 0.1 in 218.4 mmProvisionalWorked out: An assumption for the drawing, not a reading of this hand guard: Magpul's page gives no mounting length for MAG551. Magpul gives 8.6 in for its MOE M-LOK mid-length (MAG426, "Length, mounting: 8.6 in."), and for its two carbine lengths the same 6.6 in (MOE SL MAG538 and MOE M-LOK MAG424): the span a rifle's delta ring and cap hold a drop-in hand guard between, which the gas system's length sets, not the hand guard. The photo bears it out: the front sight base's rear (its tower's front leg at column 973 less the base's 1.804 in, bcm-front-sight-base-f-750.length) stands 8.47 in ahead of the bearing face read there, so the flange's end goes 0.13 past the cap's floor, which the ring's spring takes up.
Worked out 8.6 in ± 0.1 in used
An assumption for the drawing, not a reading of this hand guard: Magpul's page gives no mounting length for MAG551. Magpul gives 8.6 in for its MOE M-LOK mid-length (MAG426, "Length, mounting: 8.6 in."), and for its two carbine lengths the same 6.6 in (MOE SL MAG538 and MOE M-LOK MAG424): the span a rifle's delta ring and cap hold a drop-in hand guard between, which the gas system's length sets, not the hand guard. The photo bears it out: the front sight base's rear (its tower's front leg at column 973 less the base's 1.804 in, bcm-front-sight-base-f-750.length) stands 8.47 in ahead of the bearing face read there, so the flange's end goes 0.13 past the cap's floor, which the ring's spring takes up., harvested
Width1.8 in ± 0.05 in 45.7 mmConfirmedPublished: Magpul, MOE SL® Hand Guard, Mid-Length – AR15/M4, Model MAG551: Technical Specifications, the maker, read Oct 28, 2026
Published “Width 1.8 in.” used
Magpul, MOE SL® Hand Guard, Mid-Length – AR15/M4, Model MAG551: Technical Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Published “1/3" (15%) NARROWER PROFILE THAN ORIGINAL MOE (1.8" RATHER THAN 2.2")”
Magpul, MOE SL® Hand Guard, Mid-Length – AR15/M4, Model MAG551: Technical Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Photo 1.75 in ± 0.04 in
Magpul's feature 03 for MAG551: the black hand guard on a rifle from above, 700 x 525, harvested
Scale: its side M-LOK slots seen edge-on along each edge and its top slots: the side rows' 95.5 px for the standard's 40 mm, 60.6 px/in at the side faces. Read by the body's silhouette across, rows 213 to 318 at column 300: 106 px; its sides are further from a lens above than its top, so it reads narrow
The maker's figure, said twice on its page; the view from above, scaled at the side faces' depth, reads 3% less, as a lens close above it would.
Height2.32 in ± 0.03 in 58.9 mmCorroboratedPhoto: Magpul's mag551-odg_03: the OD green hand guard on a rifle, its right side seen level
Published “Height: 2.4 in.”
Magpul, MOE SL® Hand Guard, Mid-Length – AR15/M4, Model MAG551: Technical Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Photo 2.32 in ± 0.03 in used
Magpul's mag551-odg_03: the OD green hand guard on a rifle, its right side seen level, harvested
Scale: its M-LOK slots at the standard's pitch: 71.75 px/in. Read by the body's top (row 361) to its bottom (527.5) clear of the front lip and the grip, columns 250 to 830: 166.5 px; ± 1 px each edge
The model is drawn from the traced outline, at the photo's height. Magpul's 2.4 is 3% more, beyond the photo's ±; what it measures over isn't said (the front lip reaches lower). The carbine's own photo reads 2.32 too.
Inside diameterNo value yetMissingNo source yet
Magpul gives none. The model's inside is its outside less the wall (wall), which no view gives either.
Its rear flanges' end (bearing on the delta ring's lip) ahead of the receiver's front face0.336 in ± 0.015 in 8.5 mmProvisionalWorked out: {std.ar15.slip_ring_front_x}
Worked out 0.336 in ± 0.015 in used
{std.ar15.slip_ring_front_x}, harvested
Where the standard's delta ring holds it (std.ar15.slip_ring_front_x, from the Army's drawings): its rear flanges in the ring's skirt, against the lip. Its instruction sheet: "When both halves are in place, make sure your delta ring is securing BOTH upper and lower rear flanges of the Hand Guards".
The window in each side of its rear end, where the delta ring shows: from the tongues' rear end to the window's front edge0.68 in ± 0.03 in 17.3 mmProvisionalPhoto: Magpul's mag551-odg_03: the OD green hand guard on a rifle, its right side seen level
Photo 0.68 in ± 0.03 in used
Magpul's mag551-odg_03: the OD green hand guard on a rifle, its right side seen level, harvested
Scale: its M-LOK slots: 71.75 px/in. Read by the tongues' rear edge (column 196) to the window's front edge, where the black ring's cone ends (242.5) and the body's side begins (245): 49 px; ± 2 px
The ring fills the window in every photo of it on a rifle: its front edge is where the ring's front end is.
How far the tongues reach back over the delta ring behind its rear flanges' end0.56 in ± 0.03 in 14.2 mmProvisionalWorked out: {.window_length} - {std.ar15.slip_ring_skirt_length}
Worked out 0.56 in ± 0.03 in used
{.window_length} - {std.ar15.slip_ring_skirt_length}, harvested
The window's front edge is the ring's front end, which stands the ring's skirt ahead of the lip the flanges bear on (std.ar15.slip_ring_skirt_length).
The tongues' rear end (where the side outline begins), from its rear flanges' end-0.56 in ± 0.03 in -14.2 mmProvisionalWorked out: 0in - {.tongue_reach}
Worked out -0.56 in ± 0.03 in used
0in - {.tongue_reach}, harvested
Its top above the bore axis1.14 in ± 0.02 in 29 mmProvisionalPhoto: Magpul's mag551-odg_03: the OD green hand guard on a rifle, its right side seen level
Photo 1.14 in ± 0.02 in used
Magpul's mag551-odg_03: the OD green hand guard on a rifle, its right side seen level, harvested
Scale: its M-LOK slots: 71.75 px/in. Read by the barrel's axis ahead of the front sight base (its silhouette rows 418 to 468 at columns 1100 and 1150: centre 443) to the body's top (row 361): 82 px; ± 1 px
Its body's bottom (clear of the front lip) below the bore axis1.18 in ± 0.02 in 30 mmProvisionalPhoto: Magpul's mag551-odg_03: the OD green hand guard on a rifle, its right side seen level
Photo 1.18 in ± 0.02 in used
Magpul's mag551-odg_03: the OD green hand guard on a rifle, its right side seen level, harvested
Scale: its M-LOK slots: 71.75 px/in. Read by the barrel's axis (row 443) to the body's bottom (row 527.5, columns 250 to 550 and 670 to 830, clear of the grip): 84.5 px; ± 1 px
The seam between its two halves, on the sides, above the bore axis (negative below)-0.1 in ± 0.02 in -2.5 mmProvisionalPhoto: Magpul's mag551-odg_03: the OD green hand guard on a rifle, its right side seen level
Photo -0.1 in ± 0.02 in used
Magpul's mag551-odg_03: the OD green hand guard on a rifle, its right side seen level, harvested
Scale: its M-LOK slots: 71.75 px/in. Read by the dark line along its side (luminance 67 at row 449 to 450 between 88 above and 90 below, column 300), 7 px under the axis; ± 1 px
The room inside its M-LOK faces before what runs through it (how far an accessory's nuts may reach in)No value yetMissingNo source yet
Depends on the barrel, the gas tube and the heat shield, and on the wall, which no view gives: no figure, so the check reads as unmade.
M-LOK slots in each upper side face (the two and ten o'clock rows)4ProvisionalPhoto: Magpul's mag551-odg_03, the OD green on a rifle, its right side
Photo 4 count used
Magpul's mag551-odg_03, the OD green on a rifle, its right side, harvested
Scale: none: a count. Read by four slots in the right side's row; four along each edge from above (e31d01d48eb3), on the left on a rifle (4a086f17a6c7) and on Primary Arms' Flat Dark Earth (5ae353ae419f); the instruction sheet draws four on the mid-length
The side rows' rearmost M-LOK slot (its centre), from its rear flanges' end2.15 in ± 0.04 in 54.6 mmProvisionalPhoto: Magpul's mag551-odg_03, the OD green on a rifle, its right side seen level
Photo 2.15 in ± 0.04 in used
Magpul's mag551-odg_03, the OD green on a rifle, its right side seen level, harvested
Scale: its M-LOK slots: 71.75 px/in. Read by the rearmost slot's centre (column 390.5, between its edges at 345 and 436 at luminance 45) less the tongues' rear edge (196): 194.5 px = 2.71 in, less the tongues' reach (tongue_reach, 0.56); ± 1.5 px
The side rows' slot centres above the bore axis0.43 in ± 0.02 in 10.9 mmProvisionalPhoto: Magpul's mag551-odg_03, the OD green on a rifle, its right side seen level
Photo 0.43 in ± 0.02 in used
Magpul's mag551-odg_03, the OD green on a rifle, its right side seen level, harvested
Scale: its M-LOK slots: 71.75 px/in. Read by each slot's edges down its middle column (rows 401 to 422 at columns 430 and 600): centre 411.5, 31.5 px over the axis (row 443); ± 1 px
The side M-LOK faces' outward direction about the bore axis, from straight up (degrees)76° ± 7°ConflictPhoto: Magpul's feature 03: the black hand guard on a rifle from above) and fa1c10e48cd7 (the OD green on a rifle, its right side seen level
Published “M-LOK® slots at two, six, and ten o'clock for accessories”
Magpul, MOE SL® Hand Guard, Mid-Length – AR15/M4, Model MAG551: Technical Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Photo 76 deg ± 7 deg used
Magpul's feature 03: the black hand guard on a rifle from above) and fa1c10e48cd7 (the OD green on a rifle, its right side seen level, harvested
Scale: from above, 60.6 px/in at the side faces; level, 71.75 px/in. Read by from above, the side slots show as slits 3 to 5 px across (rows 218 to 222 and 313 to 315 at columns 166, 262 and 357), 4 px against the slot's 7 mm (std.mlok.slot_width, 16.7 px): cos ≈ 0.24, 76°; level from the side each slot is 21 px tall, the full 7 mm (19.8 px): a face within 20° of upright
Magpul's "two ... ten o'clock" says which faces, not their angle: its own photos from above and from the side both have them nearer upright.
magpul and photo differ by 16° beyond what each states it is good to.
The side rows' slot centres out from the rifle's middle plane (the middle of each face's flat)0.84 in ± 0.04 in 21.3 mmProvisionalWorked out: {.width} / 2 - {.face_flat} / 2 * cos({.mlok_side_face_angle})
Worked out 0.8395195 in ± 0.04 in used
{.width} / 2 - {.face_flat} / 2 * cos({.mlok_side_face_angle}), harvested
The face's flat runs up from the side at full width (its lower edge), leaning in at the face's angle, its middle where the photo has the slots' centres.
Where the side faces' normals through their slots' centres meet the rifle's middle plane, above the bore axis: the side M-LOK rows' axis0.221 in ± 0.06 in 5.6 mmProvisionalWorked out: {.mlok_side_slot_y} - {.mlok_side_slot_z} / tan({.mlok_side_face_angle})
Worked out 0.2206843 in ± 0.06 in used
{.mlok_side_slot_y} - {.mlok_side_slot_z} / tan({.mlok_side_face_angle}), harvested
The photos have the slots' centres higher on the faces than the foot of a line from the bore square to faces that lean as they do: the faces are angles about this axis instead (the anchor `mlok`), so that an accessory's nuts stand on the slots' centres.
The side M-LOK faces' distance from their axis (mlok_axis_y), along their outward direction0.865 in ± 0.05 in 22 mmProvisionalWorked out: {.mlok_side_slot_z} / sin({.mlok_side_face_angle})
Worked out 0.8652203 in ± 0.05 in used
{.mlok_side_slot_z} / sin({.mlok_side_face_angle}), harvested
From the axis to each slot's centre, square to its face.
M-LOK slots in the underside (six o'clock)4ProvisionalWorked out: {.mlok_side_slots}
Worked out 4 count used
{.mlok_side_slots}, harvested
The underside's rearmost M-LOK slot (its centre), from its rear flanges' end2.15 in ± 0.5 in 54.6 mmProvisionalWorked out: {.mlok_side_slot0_x}
Worked out 2.15 in ± 0.5 in used
{.mlok_side_slot0_x}, harvested
The underside's M-LOK face, its distance below the bore axis1.18 in ± 0.02 in 30 mmProvisionalWorked out: {.bottom_below_axis}
Worked out 1.18 in ± 0.02 in used
{.bottom_below_axis}, harvested
The small slots in each row along its top (one row each side of the crown)10ProvisionalPhoto: Magpul's feature 03: the black hand guard on a rifle from above
Photo 10 count used
Magpul's feature 03: the black hand guard on a rifle from above, harvested
Scale: none: a count. Read by ten in each row (rows 240 and 296, columns 56 to 513); ten along the top edge in the level photo (c706e2992834) and on Primary Arms' Flat Dark Earth (5ae353ae419f)
The rearmost top slot's centre, from its rear flanges' end0.52 in ± 0.06 in 13.2 mmProvisionalPhoto: Magpul's feature 03: from above
Photo 0.52 in ± 0.06 in used
Magpul's feature 03: from above, harvested
Scale: its side slots seen edge-on, 95.5 px apart for the standard's 40 mm: 60.6 px/in. Read by the rearmost top slot's centre (column 67) 99 px behind the side row's rearmost slot's (166): 1.63 in behind mlok_side_slot0_x
The top slots, centre to centre0.8 in ± 0.01 in 20.3 mmProvisionalPhoto: Magpul's feature 03: from above
Photo 0.8 in ± 0.01 in used
Magpul's feature 03: from above, harvested
Scale: 60.6 px/in. Read by the ten centres at 67 to 503 px in both rows: 48.4 px a pitch (the standard's 20 mm M-LOK interval is 0.787)
Each row of top slots, its centre line from the middle of the top0.46 in ± 0.03 in 11.7 mmProvisionalPhoto: Magpul's feature 03: from above
Photo 0.46 in ± 0.03 in used
Magpul's feature 03: from above, harvested
Scale: 60.6 px/in. Read by the rows at 240 and 296 px, the body's middle at 265.5 (its silhouette 213 to 318): 28 px each side
Each top slot's length along it0.36 in ± 0.02 in 9.1 mmProvisionalPhoto: Magpul's feature 03: from above
Photo 0.36 in ± 0.02 in used
Magpul's feature 03: from above, harvested
Scale: 60.6 px/in. Read by the dark runs along rows 240 and 296, 21 to 23 px
Each top slot's width across0.115 in ± 0.02 in 2.9 mmProvisionalPhoto: Magpul's feature 03: from above
Photo 0.115 in ± 0.02 in used
Magpul's feature 03: from above, harvested
Scale: 60.6 px/in. Read by the slot at column 262 across, rows 237 to 243: 7 px
The grooves along its crown, between the two rows of top slots8ProvisionalPhoto: Magpul's feature 03: from above
Photo 8 count used
Magpul's feature 03: from above, harvested
Scale: none: a count. Read by eight dark minima across column 300 between rows 255 and 282 (about 3.4 px apart)
The grooved strip's width across the crown0.4 in ± 0.04 in 10.2 mmProvisionalPhoto: Magpul's feature 03: from above
Photo 0.4 in ± 0.04 in used
Magpul's feature 03: from above, harvested
Scale: 60.6 px/in. Read by the first and the last minimum across column 300, rows 258 and 282: 24 px
Where the grooved strip ends at the front, from its rear flanges' end8.32 in ± 0.1 in 211.3 mmProvisionalPhoto: Magpul's feature 03: from above
Photo 8.32 in ± 0.1 in used
Magpul's feature 03: from above, harvested
Scale: 60.6 px/in. Read by the dark strip along row 268 ends at column 540 (its rounded end), 6.17 in ahead of the side row's rearmost slot (166 px)
Each crown groove's depth0.015 in ± 0.01 in 0.4 mmProvisionalWorked out: An assumption for the drawing, not a reading: the grooves are seen from above only.
Worked out 0.015 in ± 0.01 in used
An assumption for the drawing, not a reading: the grooves are seen from above only., harvested
The upright ribs along each side of the lower half9ProvisionalPhoto: Magpul's mag551-odg_03, the OD green on a rifle, its right side
Photo 9 count used
Magpul's mag551-odg_03, the OD green on a rifle, its right side, harvested
Scale: none: a count. Read by nine lines down the lower half between the window and the front panel (row 470: columns 301, 357.5, 413.5, 470.5, 527, 583.5, 640, 696.5, 753.5); nine on the close photo of its side (a6cff9cf637f)
The rearmost rib, from its rear flanges' end0.9 in ± 0.03 in 22.9 mmProvisionalPhoto: Magpul's mag551-odg_03, the OD green on a rifle, its right side seen level
Photo 0.9 in ± 0.03 in used
Magpul's mag551-odg_03, the OD green on a rifle, its right side seen level, harvested
Scale: 71.75 px/in. Read by column 301, 105 px ahead of the tongues' rear edge (196) = 1.46 in, less tongue_reach
The ribs, one to the next0.788 in ± 0.005 in 20 mmProvisionalPhoto: Magpul's mag551-odg_03, the OD green on a rifle, its right side seen level
Photo 0.788 in ± 0.005 in used
Magpul's mag551-odg_03, the OD green on a rifle, its right side seen level, harvested
Scale: 71.75 px/in. Read by eight gaps from 301 to 753.5 px: 56.6 px each (the standard's 20 mm M-LOK interval is 0.787)
Each rib's width0.06 in ± 0.02 in 1.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: each rib shows as a lit and a shaded line, 4 to 5 px together at 71.75 px/in on the close photo of its side (a6cff9cf637f).
Worked out 0.06 in ± 0.02 in used
An assumption for the drawing, not a reading: each rib shows as a lit and a shaded line, 4 to 5 px together at 71.75 px/in on the close photo of its side (a6cff9cf637f)., harvested
How far each rib stands from the panels between them0.03 in ± 0.015 in 0.8 mmProvisionalWorked out: An assumption for the drawing, not a reading: the ribs cast short shadows in Magpul's close photo of its side (a6cff9cf637f), never seen in profile.
Worked out 0.03 in ± 0.015 in used
An assumption for the drawing, not a reading: the ribs cast short shadows in Magpul's close photo of its side (a6cff9cf637f), never seen in profile., harvested
The small slots in each row along the lower edges13ProvisionalPhoto: Magpul's mag551-blk_03: the black hand guard on a rifle, its right side seen level
Photo 13 count used
Magpul's mag551-blk_03: the black hand guard on a rifle, its right side seen level, harvested
Scale: none: a count. Read by thirteen notches along the bottom edge, one between each two ribs and on under the front panel (columns 268 to 950, by eye on a crop at 1.9 times)
The rearmost lower-edge slot's centre, from its rear flanges' end0.51 in ± 0.08 in 13 mmProvisionalPhoto: Magpul's mag551-odg_03, its right side seen level
Photo 0.51 in ± 0.08 in used
Magpul's mag551-odg_03, its right side seen level, harvested
Scale: 71.75 px/in. Read by the notches stand between the ribs (one between the ribs at 413.5 and 470.5 px has its ends at 424 and 458, centred at 441): the first between the window's front edge (245) and the first rib (301), at 273, = 0.51 from the bearing face
The lower-edge slots, centre to centre0.788 in ± 0.005 in 20 mmProvisionalWorked out: {.rib_pitch}
Worked out 0.788 in ± 0.005 in used
{.rib_pitch}, harvested
One between each two ribs: the ribs' pitch.
Each lower-edge slot's length0.47 in ± 0.04 in 11.9 mmProvisionalPhoto: Magpul's mag551-odg_03, its right side seen level
Photo 0.47 in ± 0.04 in used
Magpul's mag551-odg_03, its right side seen level, harvested
Scale: 71.75 px/in. Read by the notch between the ribs at 413.5 and 470.5 px, its ends at 424 and 458: 34 px
Each lower-edge slot's width0.1 in ± 0.03 in 2.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the notches show edge-on along the bottom edge from the side, a few pixels tall.
Worked out 0.1 in ± 0.03 in used
An assumption for the drawing, not a reading: the notches show edge-on along the bottom edge from the side, a few pixels tall., harvested
How deep the top and lower-edge slots go (they are blind)0.06 in ± 0.03 in 1.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view shows one in section; from above they show dark, not the barrel.
Worked out 0.06 in ± 0.03 in used
An assumption for the drawing, not a reading: no view shows one in section; from above they show dark, not the barrel., harvested
Its polymer wall's thickness0.15 in ± 0.04 in 3.8 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows an end square on or a section. Taken so that the model comes near Magpul's 8.3 oz at the polymer's density on file (std.density.polymer) with its aluminium heat shield; what it still lacks is the inner ribs and bosses no view shows.
Worked out 0.15 in ± 0.04 in used
An assumption for the drawing, not a reading: no view on file shows an end square on or a section. Taken so that the model comes near Magpul's 8.3 oz at the polymer's density on file (std.density.polymer) with its aluminium heat shield; what it still lacks is the inner ribs and bosses no view shows., harvested
Its aluminium heat shield's thickness0.03 in ± 0.015 in 0.8 mmProvisionalWorked out: An assumption for the drawing, not a reading: Magpul's feature 04 (70b6f543f381) shows the lower half with its shield, edge-on a few pixels thick.
Worked out 0.03 in ± 0.015 in used
An assumption for the drawing, not a reading: Magpul's feature 04 (70b6f543f381) shows the lower half with its shield, edge-on a few pixels thick., harvested
The seam's groove along each side (its width and its depth)0.02 in ± 0.01 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the seam shows as a dark line one or two pixels wide at 71.75 px to the inch, its depth on no view.
Worked out 0.02 in ± 0.01 in used
An assumption for the drawing, not a reading: the seam shows as a dark line one or two pixels wide at 71.75 px to the inch, its depth on no view., harvested
Each upper side face's flat (where its M-LOK slots are), its height across the face0.5 in ± 0.1 in 12.7 mmProvisionalWorked out: An assumption for the drawing, not a reading: the slot's 7 mm and a margin each side, as the close photo of its side (a6cff9cf637f) shows the face round its slots.
Worked out 0.5 in ± 0.1 in used
An assumption for the drawing, not a reading: the slot's 7 mm and a margin each side, as the close photo of its side (a6cff9cf637f) shows the face round its slots., harvested
Its top's flat (the crown with its two rows of slots), half its width0.6 in ± 0.1 in 15.2 mmProvisionalWorked out: An assumption for the drawing, not a reading: no end view on file; from above, the two rows of top slots stand 0.46 either side of the middle, seen whole (not foreshortened), so the top is near flat that far out and a little more.
Worked out 0.6 in ± 0.1 in used
An assumption for the drawing, not a reading: no end view on file; from above, the two rows of top slots stand 0.46 either side of the middle, seen whole (not foreshortened), so the top is near flat that far out and a little more., harvested
Its underside's flat (where the six o'clock slots are), half its width0.42 in ± 0.1 in 10.7 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view looks at the mid-length's underside; wide enough for its M-LOK slots and a margin each side, rounding into the sides at the lower-edge slots.
Worked out 0.42 in ± 0.1 in used
An assumption for the drawing, not a reading: no view looks at the mid-length's underside; wide enough for its M-LOK slots and a margin each side, rounding into the sides at the lower-edge slots., harvested
Where the side rounds under into the underside, above the bore axis (negative below)-0.8 in ± 0.1 in -20.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: the lower-edge slots are on the round, seen from the side as notches along the bottom edge (c706e2992834).
Worked out -0.8 in ± 0.1 in used
An assumption for the drawing, not a reading: the lower-edge slots are on the round, seen from the side as notches along the bottom edge (c706e2992834)., harvested
Its front flange (what goes into the round cap), outside diameter1.36 in ± 0.05 in 34.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: Magpul's instructions slide the flange "into the metal hand guard cap"; no view shows it. Taken inside the round cap on file (bcm-handguard-cap-round-750, its tabs at 3 and 9 o'clock to 0.690 from the axis).
Worked out 1.36 in ± 0.05 in used
An assumption for the drawing, not a reading: Magpul's instructions slide the flange "into the metal hand guard cap"; no view shows it. Taken inside the round cap on file (bcm-handguard-cap-round-750, its tabs at 3 and 9 o'clock to 0.690 from the axis)., harvested
Its front flange's length (into the cap)0.42 in ± 0.1 in 10.7 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view shows the flange from the side. Long enough that the front wall it stands from stays behind the round cap's rim with the flange home (the cap is 0.276 deep).
Worked out 0.42 in ± 0.1 in used
An assumption for the drawing, not a reading: no view shows the flange from the side. Long enough that the front wall it stands from stays behind the round cap's rim with the flange home (the cap is 0.276 deep)., harvested
Its rear flanges (what stands in the delta ring's skirt), outside diameter1.72 in ± 0.03 in 43.7 mmProvisionalWorked out: An assumption for the drawing, not a reading: the flanges stand in the delta ring's skirt (std.ar15.slip_ring_skirt_d, 1.750 inside) and show on no photo; taken 0.03 under the skirt.
Worked out 1.72 in ± 0.03 in used
An assumption for the drawing, not a reading: the flanges stand in the delta ring's skirt (std.ar15.slip_ring_skirt_d, 1.750 inside) and show on no photo; taken 0.03 under the skirt., harvested
The room between the tongues and the delta ring they reach back over0.02 in ± 0.02 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the tongues stand over the ring (std.ar15.slip_ring_od, 2.1) and their inside is seen on no photo.
Worked out 0.02 in ± 0.02 in used
An assumption for the drawing, not a reading: the tongues stand over the ring (std.ar15.slip_ring_od, 2.1) and their inside is seen on no photo., harvested
Its front wall (the inner face the front flange stands from), from its rear flanges' end8.03 in ± 0.15 in 204 mmProvisionalWorked out: {.mounting_length} - {.front_flange_length} - {.wall}
Worked out 8.03 in ± 0.15 in used
{.mounting_length} - {.front_flange_length} - {.wall}, harvested
Ahead of the wall the shell runs on as its side extensions and its front lip, open over the top, round the cap and the front sight base ("Hand Guard will wrap around the front sight when mounted").
Its front panel's width (it stands out from the body round the cap and the front sight base)1.97 in ± 0.05 in 50 mmProvisionalPhoto: Magpul's feature 03: the black hand guard on a rifle from above
Photo 1.97 in ± 0.05 in used
Magpul's feature 03: the black hand guard on a rifle from above, harvested
Scale: the body's width beside it, Magpul's 1.8 in (width), at the same depth. Read by the front panel's silhouette across, rows 206 to 323 at columns 560 and 600: 118 px, against the body's 108 (rows 211 to 318 at column 480): 1.093 times Magpul's width
Where the front panel stands out from the body, from its rear flanges' end7.99 in ± 0.1 in 202.9 mmProvisionalPhoto: Magpul's feature 03: the black hand guard on a rifle from above
Photo 7.99 in ± 0.1 in used
Magpul's feature 03: the black hand guard on a rifle from above, harvested
Scale: its side slots seen edge-on: 60.6 px/in. Read by the silhouette's step out along rows 210 and 322 at columns 516 and 525 (520.5), 5.85 in ahead of the side row's rearmost slot (166 px)
The room inside its front panel round the hand guard cap1.733 in ± 0.04 in 44 mmProvisionalWorked out: {bcm-handguard-cap-round-750.lip_od} + 2 * {.ring_clearance}
Worked out 1.7329 in ± 0.04 in used
{bcm-handguard-cap-round-750.lip_od} + 2 * {.ring_clearance}, harvested
The front panel wraps the round cap ("Hand Guard will wrap around the front sight when mounted"): its inside is the cap's own outside and a clearance (ring_clearance), the one round cap on file.
The round at the top of its front edge (where the side extensions' level top turns down the front), its length along0.15 in ± 0.04 in 3.8 mmProvisionalPhoto: Magpul's mag551-blk_03: the black hand guard on a rifle, its right side seen level; the photograph the OD green one traced is recoloured from
Photo 0.15 in ± 0.04 in used
Magpul's mag551-blk_03: the black hand guard on a rifle, its right side seen level; the photograph the OD green one traced is recoloured from, harvested
Scale: 71.75 px/in by its M-LOK slots. Read by the level top's edge ends and the round begins 11 px behind the front edge (by eye on a crop at 3 to 5 times; the front sight base's front leg stands just ahead of it)
The traced outline's corner here is the front sight's leg's, not the part's: the model draws this round instead (clean_nose in the script).
The same round's height down the front edge0.23 in ± 0.05 in 5.8 mmProvisionalPhoto: Magpul's mag551-blk_03: the black hand guard on a rifle, its right side seen level; the photograph the OD green one traced is recoloured from
Photo 0.23 in ± 0.05 in used
Magpul's mag551-blk_03: the black hand guard on a rifle, its right side seen level; the photograph the OD green one traced is recoloured from, harvested
Scale: 71.75 px/in by its M-LOK slots. Read by the front edge runs straight from 17 px under the level top (by eye on the same crop)
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Drop-in handguard's front in its cap
Handguard mount
Drop-in handguard's hold
- Delta rings
- BCM Delta Ring Assembly - AR15
Gas system length
- Barrels
- Aero Precision 16" 5.56 CMV barrel, mid-length, BCM Standard 14.5" Mid Length Barrel, Stripped, BCM Standard 16" Mid Length Barrel, Stripped, Bear Creek Arsenal BC-15 5.56 NATO, 16" Parkerized M4 Barrel, 1:7 Twist, Mid-Length Gas System, Faxon Firearms Duty Series Pencil Profile 16" Mid-Length 5.56 NATO AR15 Barrel, Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 13.9", Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 14.5", Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 16"
M-LOK
- Hand stops
- BCM KAG (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK Hand Stop (fit unchecked), Magpul M-LOK Index Panel (fit unchecked)
- Vertical grips
- BCM Vertical Grip Mod 3 (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK MVG vertical grip (fit unchecked)
- Lights
- Cloud Defensive REIN (fit unchecked), Streamlight ProTac Rail Mount HL-X (fit unchecked), SureFire Mini Scout Light Pro (fit unchecked), SureFire Scout Light Pro Dual Fuel (fit unchecked)
- Rail sections
- Magpul M-LOK® Aluminum Rail, 3 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 5 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 7 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 9 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 11 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 3 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 5 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 7 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 9 Slots (fit unchecked)
- Adapter plates
- Magpul M-LOK Hand Stop MOE Adapter (fit unchecked)
- Sling mounts
- Magpul M-LOK QD Sling Mount (fit unchecked)
- Rail covers
- Magpul M-LOK Rail Cover Type 2 (fit unchecked)
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- KYGUNCO $31.13 Olive Drab Green Nov 21, 2026, in stock that day
- Primary Arms $32.26 Flat Dark Earth Nov 17, 2026, in stock that day
- Midwest Gun Works $37.95 Black Nov 21, 2026, in stock that day
- Midwest Gun Works $37.95 Flat Dark Earth Nov 21, 2026, in stock that day
- Midwest Gun Works $37.95 Olive Drab Green Nov 21, 2026, in stock that day
- Midwest Gun Works $37.95 Stealth Gray Nov 21, 2026, in stock that day
- Magpul $39.95 Black Nov 21, 2026, stock not said
- Magpul $39.95 Flat Dark Earth Nov 21, 2026, stock not said
- Magpul $39.95 Olive Drab Green Nov 21, 2026, stock not said
- Magpul $39.95 Stealth Gray Nov 21, 2026, stock not said