Rail section
Magpul M-LOK® Polymer Rail, 3 Slots
A 3-slot Picatinny rail in Magpul's polymer that bolts straight to a hand guard's M-LOK slots, for a light, a grip or another rail-mounted accessory. Magpul: "Our polymer rail segment attaches to any M-LOK interface for a 3-slot Picatinny mount for lights, vertical grips, or other 1913 rail compatible accessories." It has a screw hole in each end slot, two pitches apart (the M-LOK interval: both T-nuts in one slot), cammed T-nuts and recoil lugs under it, and bevelled ends. Black only (MAG589-BLK). NSN 1005-01-666-0491.

- Weight
- 0.17 oz ± 0.05 oz Provisionalworked out: The model's polymer volume, 0.2617 cubic inches (the manifest's body_volume_in3; the screws' heads apart), times std.density.polymer (Zytel nylon 66, 18.68 g, 0.659 oz to the cubic inch): 0.172 oz. Magpul names no grade ("a proprietary reinforced composite"): a glass-filled grade is up to a sixth heavier, the underside's pocket isn't drawn (the model is solid under its rail), and the height and the neck are readings or assumptions with their own ±; the ± takes all of them. The steel T-nuts and screws aren't in it.
- Lowest price
- $11.95 at Magpul, read Nov 21, 2026 (Black)
- Maker's number
- MAG589
- Colour
- Magpul Black
- Drawn as
- modelled
- Maker's page
- magpul.com
Added to “22RB .22 LR rifle”, a build on the start page, where the designer starts a new rail section.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Overall length (along the handguard)1.575 in ± 0.02 in 40 mmCorroboratedPhoto: Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above
Published “1.6" 3-slot Picatinny rail segment easily attaches to any M-LOK mounting interface”
Magpul, M-LOK® Polymer Rail, 3 Slots (MAG589), Product Details, the maker, read Oct 29, 2026 the page, harvested Oct 29, 2026
Published “MAG589 - 3 Slots, max overall length of 1.6” NSN:1005016660491”
Magpul, M-LOK® Polymer Rail Sections GIS sheet (MAG589-MAG593), page 1, the maker, read Oct 29, 2026 the page, harvested Oct 29, 2026
Photo 1.575 in ± 0.02 in used
Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above, harvested
Scale: its own rail slots at the standard's pitch (std.picatinny.slot_pitch, 0.394 in: Magpul's sheet, "1913 Picatinny spec rail-mounted accessories"): the three slots' centres at columns 228.3, 347.5 and 463.5, 117.6 px apart: 298.5 px/in. Read by the outline's two ends on the rows through its middle (the white ground beside the hand guard), columns 111.7 and 581.7: 470 px; ± covers 2 px at each end and the pitch's ± 1.5 px
Read square on, on a white ground, by its own slots; Magpul's "max overall length of 1.6" says the same within its last digit.
The two ends of its outline, square from above. The slots are centred on it: 116.6 px from the rear end to the rear slot's centre, 118.2 from the front slot's centre to the front end.
Height (its rail's top above the handguard's face it sits on)0.33 in ± 0.04 in 8.4 mmProvisionalWorked out: An assumption for the drawing, not a reading: no photo of this length shows its side well enough to read. Magpul's studio photos of the 7-slot and the 9-slot, read the same way (the top flat's foreshortening against the standard's 0.656 in for the camera's elevation, the band below it for the side), give 0.316 and 0.345 in; Magpul's sheet and pages describe the five lengths as one moulding in five lengths. The ± covers both.
Worked out 0.33 in ± 0.04 in used
An assumption for the drawing, not a reading: no photo of this length shows its side well enough to read. Magpul's studio photos of the 7-slot and the 9-slot, read the same way (the top flat's foreshortening against the standard's 0.656 in for the camera's elevation, the band below it for the side), give 0.316 and 0.345 in; Magpul's sheet and pages describe the five lengths as one moulding in five lengths. The ± covers both., harvested
From the mounting face (the face that bears on the hand guard) to the rail's top.
Width (side to side, at its widest under the rail's head)0.811 in ± 0.015 in 20.6 mmProvisionalPhoto: Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above
Photo 0.811 in ± 0.015 in used
Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above, harvested
Scale: the length's scale (298.5 px/in, its own slots). Read by the outline across its middle (columns 330 to 370 averaged): rows 151 to 393 at half tone, 242 px; ± covers 2 px at each edge
The outline across, from above: the rail's head is the standard's (0.835 in at its widest), and the outline reads 0.811; the model takes this as its body under the head.
Rail slots3CorroboratedPhoto: Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above
Published “M-LOK® Polymer Rail, 3 Slots”
Magpul, M-LOK® Polymer Rail, 3 Slots (MAG589), Product Details, the maker, read Oct 29, 2026 the page, harvested Oct 29, 2026
Photo 3 count used
Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above, harvested
Scale: none: a count. Read by three slots between its two ends, a screw in the first and the third
Counted on the part; the name says the same.
Rear rail slot's centre ahead of the part's rear end0.394 in 10 mmCorroboratedWorked out: ({.length} - ({.rail_slots} - 1) * {std.picatinny.slot_pitch}) / 2
Worked out 0.3935 in used
({.length} - ({.rail_slots} - 1) * {std.picatinny.slot_pitch}) / 2, harvested
Centred on its length: the top view has 116.6 px from its rear end to the rear slot's centre and 118.2 from the front slot's centre to the front end.
Rail slot its rear screw hole is in (counted from its rear end, the first is 1)1ProvisionalPhoto: Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above
Photo 1 count used
Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above, harvested
Scale: none: a count. Read by the two screws' centres at columns 228 and 463, within 1 px of the first and the third slots' centres
Rail slots from its rear screw hole to its front one (pitches)2ProvisionalPhoto: Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above
Photo 2 count used
Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above, harvested
Scale: none: a count. Read by the two screws' centres at columns 228 and 463, within 1 px of the first and the third slots' centres
Two screw holes, one in each end slot, two pitches apart (0.788 in): the M-LOK interval (20 mm), so its two T-nuts go into the two halves of one M-LOK slot.
M-LOK slots its T-nuts span1ProvisionalPhoto: Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above
Photo 1 count used
Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above, harvested
Scale: none: a count. Read by its two screws two rail pitches apart (0.788 in, the M-LOK interval): both T-nuts in one M-LOK slot
One M-LOK slot: its two T-nuts 20 mm apart in its two halves, as Magpul's hand stop's.
Its seat on the M-LOK face: the centre of the M-LOK slot its rear T-nut is in, ahead of its rear end0.787 in 20 mmProvisionalWorked out: {.rail_slot0_x} + ({.rear_hole_slot} - 1) * {std.picatinny.slot_pitch} + {std.mlok.interval} / 2
Worked out 0.7872 in used
{.rail_slot0_x} + ({.rear_hole_slot} - 1) * {std.picatinny.slot_pitch} + {std.mlok.interval} / 2, harvested
The rear screw hole is at its slot's centre (the photos), and its T-nut sits in the rear half of an M-LOK slot, half the M-LOK interval behind that slot's centre: what an M-LOK position places is that slot's centre. Two T-nuts the interval apart then sit one in each half of one slot (the 3-slot: the hand stop's seat); one a slot pitch further on sits in the rear half of the next. Magpul's page: "Integral recoil lugs resist impact and keep rail secured under recoil and provide an intermediate spacing option" (the lugs under it between its nuts, which go into a slot), and its M-LOK page: "Your M-LOK accessory can be adjusted in 20mm increments (1/2 slot length)". Which half of a slot a nut is in isn't published: the rear half is assumed.
Reach inside the handguard (below the mounting face, tightened)No value yetMissingNo source yet
Not published: Magpul gives no figure for its cammed T-nuts or for the recoil lugs under the section.
Under the head: where its lower faces, carried on at 45 degrees past the lower gauge line, meet the neck, below the rail's top0.2 in ± 0.05 in 5.1 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view of the part along its rail is on file, and the neck stands in the head's shadow in every photo. The head's lower faces are carried on at the standard's 45 degrees to here, as Midwest Industries' drop-in rail's are to theirs (0.204 in, read on its photo), so that what clamps a rail has room for its jaws under the head; the ± covers a neck from the standard's lower gauge width to two tenths narrower.
Worked out 0.2 in ± 0.05 in used
An assumption for the drawing, not a reading: no view of the part along its rail is on file, and the neck stands in the head's shadow in every photo. The head's lower faces are carried on at the standard's 45 degrees to here, as Midwest Industries' drop-in rail's are to theirs (0.204 in, read on its photo), so that what clamps a rail has room for its jaws under the head; the ± covers a neck from the standard's lower gauge width to two tenths narrower., harvested
The head's lower faces are MIL-STD-1913's to its lower gauge line (std.picatinny.lower_gauge_below_top); under them the section narrows to a neck that leaves a clamp's jaws room under the head, then widens again to its width at a shoulder near the mounting face (neck_foot_above_face). With the standard's head (lib.rail_half) this sets the neck's half width.
Under the head: the neck's foot (the shoulder where the section widens to its width) above the mounting face0.055 in ± 0.03 in 1.4 mmProvisionalWorked out: An assumption for the drawing, not a reading: no photo of this length's side shows its shoulder. The 5-slot's underside photo (e389e392fb30) reads 0.055 in; the ± covers it.
Worked out 0.055 in ± 0.03 in used
An assumption for the drawing, not a reading: no photo of this length's side shows its shoulder. The 5-slot's underside photo (e389e392fb30) reads 0.055 in; the ± covers it., harvested
Each end's slope, along the part: from the end to where its rail's top begins0.195 in ± 0.02 in 5 mmProvisionalPhoto: Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above
Photo 0.195 in ± 0.02 in used
Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above, harvested
Scale: the length's scale (298.5 px/in). Read by where the top's flat ends and the slope begins: columns 168.3 and 521.7, 56.6 and 60.0 px in from the two ends
Magpul: "The beveled ends reduce snagging and eliminate sharp corners and edges." The end face slopes and rounds down from the top to a short upright face at the mounting face (the photos from above and from the end).
Each end's upright face under its slope, above the mounting face0.08 in ± 0.04 in 2 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows it in profile.
Worked out 0.08 in ± 0.04 in used
An assumption for the drawing, not a reading: no view on file shows it in profile., harvested
Each end's corners cut off in plan, along the end0.13 in ± 0.03 in 3.3 mmProvisionalPhoto: Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above
Photo 0.13 in ± 0.03 in used
Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above, harvested
Scale: the length's scale (298.5 px/in). Read by the outline's corners at the ends cut on a slant from about 46 px along the side to 38 px across the end; ± covers reading the slant's ends by eye
Each screw hole's recess, across0.43 in ± 0.02 in 10.9 mmProvisionalPhoto: Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above
Photo 0.43 in ± 0.02 in used
Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above, harvested
Scale: the length's scale (298.5 px/in). Read by the recess's rim round each screw, 128 px across on a threefold enlargement read by eye
A round recess round each screw hole, into the slot it is in and the lands either side of it (every photo of the part from above).
The recess's floor above the mounting face (where the screw's head bears)0.12 in ± 0.04 in 3 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows it in profile.
Worked out 0.12 in ± 0.04 in used
An assumption for the drawing, not a reading: no view on file shows it in profile., harvested
Screw hole, through0.21 in ± 0.03 in 5.3 mmProvisionalPhoto: Magpul's mag589-blk_01, 1200 x 1200: the 3-slot alone from above and in front, no screws in
Photo 0.21 in ± 0.03 in used
Magpul's mag589-blk_01, 1200 x 1200: the 3-slot alone from above and in front, no screws in, harvested
Scale: the hole against its recess (.counterbore_diameter) on one circle's axis. Read by the white hole about half its recess's width, by eye
Screw's head, across0.396 in ± 0.02 in 10.1 mmProvisionalPhoto: Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above
Photo 0.396 in ± 0.02 in used
Magpul's mag589-feature_01, 700 x 525: the 3-slot on a MOE M-LOK hand guard's top face, its two screws in, seen square from above, harvested
Scale: the length's scale (298.5 px/in). Read by each screw's dark head (its knurled rim), 118 px across on a threefold enlargement read by eye
Its two screws are black socket button heads (Magpul's photo of the hardware under the 5- and 7-slot sections: two screws and two T-nuts).
Screw's head, from the recess's floor to its crown0.06 in ± 0.03 in 1.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows it in profile.
Worked out 0.06 in ± 0.03 in used
An assumption for the drawing, not a reading: no view on file shows it in profile., harvested
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
M-LOK
- Uppers
- Nordic Components 22RB .22 LR upper, 16" (fit unchecked), Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12" (fit unchecked), Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16" (fit unchecked)
- Handguards
- Aero Precision AR15 10.3" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 12.7" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 15" Enhanced M-LOK Handguard, Gen 2 (fit unchecked), Aero Precision AR15 15" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 15" S-ONE M-LOK Handguard (fit unchecked), Aero Precision AR15 16.6" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 7.3" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 9.3" R-ONE M-LOK handguard (fit unchecked), BCM MCMR-10 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM MCMR-13 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM MCMR-15 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM PMCR (Polymer M-LOK® Compatible Rail)* Carbine Length-BLACK (fit unchecked), BCM PMCR (Polymer M-LOK® Compatible Rail)* Mid Length-BLACK (fit unchecked), Expo Arms Free Float AR-15 Handguard - M-LOK - 15" (fit unchecked), Geissele Automatics 10.5" Super Modular Rail MK16 M-LOK (fit unchecked), Geissele Automatics 13.5" Super Modular Rail MK16 M-LOK (fit unchecked), Geissele Automatics 15" Super Modular Rail MK16 M-LOK (fit unchecked), Magpul MOE SL® Hand Guard, Carbine-Length – AR15/M4 (fit unchecked), Magpul MOE SL® Hand Guard, Mid-Length – AR15/M4 (fit unchecked), Magpul MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4 (fit unchecked), Magpul MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4 (fit unchecked), MAS Defense 12.62" NERO M-LOK FREE FLOAT (fit unchecked), MAS Defense 15" NERO M-LOK FREE FLOAT (fit unchecked), MAS Defense 9.87" NERO M-LOK FREE FLOAT (fit unchecked), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine) (fit unchecked), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length) (fit unchecked), Midwest Industries Combat Rail One Piece Free Float Handguard, M-LOK™ (15") (fit unchecked)
- Adapter plates
- Magpul M-LOK Hand Stop MOE Adapter (fit unchecked)
Picatinny rail (MIL-STD-1913)
- Red dot mounts
- Aimpoint Duty RDS One-piece TNP Mount, 30 mm, Aimpoint LRP (Lever Release Picatinny) Mount with 39 mm Spacer, for Micro, Aimpoint One-piece Torsion Nut Mount and Spacer, 39 mm, Geissele Super Precision T1 Mount - 1.93" Height, Geissele Super Precision T1 Mount - Absolute Co-Witness, Geissele Super Precision T1 Mount - Lower 1/3 Co-Witness, Holosun 1.63 in lower 1/3 co-witness pedestal mount (HS-MOUNT-AR-RISER-ARO), Midwest Industries MK2 QD T2 Aimpoint Mount, Low, Midwest Industries MK2 QD T2 Aimpoint Mount, Lower 1/3 Cowitness, Midwest Industries MK2 QD T2 Aimpoint Mount, NV 2.26 in Height, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – 1.93″ HEIGHT, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – LOWER 1/3 (39MM HEIGHT), Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.42 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.57 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.93 in, Scalarworks LEAP/02 Aimpoint Micro T-2 quick-detach mount, 2.26 in, SIG Sauer M1913 I-BEAM Mount, 1.41 in absolute co-witness, SIG Sauer See-Through Riser Mount, 1.41 in absolute co-witness, Unity Tactical FAST Micro Mount, 2.26 in optical centerline
- Optics
- Aimpoint Patrol Rifle Optic (PRO) Red Dot Reflex Sight - QRP2 Mount, EOTECH HWS EXPS3 holographic weapon sight, 1-Dot Speed Ring, Holosun HS510C Open Reflex MRS Solar QD Mount
- Lights
- Olight Baldr S BL, Streamlight ProTac Rail Mount HL-X, SureFire Mini Scout Light Pro, SureFire Scout Light Pro Dual Fuel
- Backup sights
- Daniel Defense A1.5 Fixed Rear Sight, Daniel Defense Rail Mounted Fixed Front Sight, Magpul MBUS 3 Sight – Front, Magpul MBUS 3 Sight – Rear, Magpul MBUS Pro Sight – Front, Magpul MBUS Pro Sight – Rear
- Magnifiers
- EOTECH G33 Magnifier, STS Mount, EOTECH G45 Magnifier, STS Mount, Holosun HM3X 3× magnifier with flip mount
- Scope mounts
- Primary Arms Deluxe AR-15 Scope Mount - 30mm, Primary Arms SLx Cantilever 30mm Mount - 1.5", Reptilia AUS™ MOUNT - 30MM DIAMETER - 39MM HEIGHT, Scalarworks LEAP/08 quick-detach scope mount, 30 mm, 1.57 in, SIG SAUER ALPHA-MSR scope mount, 30 mm, Vortex Sport Cantilever 30mm Mount
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Magpul $11.95 Black Nov 21, 2026, stock not said