Handguard
Expo Arms Free Float AR-15 Handguard - M-LOK - 15"
Expo Arms' 15 in free-float M-LOK handguard (Expo Arms is Primary Arms' house brand): 6061-T6 aluminum, a full top Picatinny rail, M-LOK slots on seven sides, two anti-rotation tabs, clamped on its own 6061-T6 aluminum barrel nut by three cross bolts. "Compatible with all Mil-Spec upper receivers".

- Weight
- 13.2 oz ± 0.05 oz Conflictpublished: Primary Arms (Expo Arms is its house brand), Expo Arms Free Float AR-15 Handguard - M-LOK - 15" (XP-GUARD15-BLK), Specifications; its Features say "13.2 oz weight", the maker, read Oct 5, 2026Its sources span 13.15 oz to 18.25 oz.
- Lowest price
- $99.99 at Primary Arms, read Nov 21, 2026 (Black (hardcoat anodized))
- Maker's number
- XP-GUARD15-BLK
- Colours
- Black (hardcoat anodized), FDE (Cerakote)
- Drawn as
- modelled
- Maker's page
- primaryarms.com
In “Budget 16 in carbine”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Length (its rear face to its front face; the two tabs reach 0.19 in further back)15 in ± 0.5 in 381 mmConfirmedPublished: Primary Arms, Expo Arms Free Float AR-15 Handguard - M-LOK - 15" (XP-GUARD15-BLK), Specifications; its Features say '15" length', the maker, read Oct 5, 2026
Published “Handguard Length 15” used
Primary Arms, Expo Arms Free Float AR-15 Handguard - M-LOK - 15" (XP-GUARD15-BLK), Specifications; its Features say '15" length', the maker, read Oct 5, 2026 the page, harvested Oct 5, 2026
Photo 14.99 in ± 0.03 in
Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467, harvested
Scale: its own top rail: the 35 teeth between its end lands, one Picatinny pitch apart (std.picatinny.slot_pitch), fitted along the photo (127.6 px/in at the rear end, 129.6 in the middle, 125.6 at the front; rms 0.0006 in). Read by the silhouette's ends on the rows of the side face, 0.911 behind the rearmost tooth's centre and 14.276 ahead of it as the teeth read them; they are the side face's edges, 0.44 in nearer the lens than the teeth's near sides, and the lens is 33.2 in away with its foot 7.04 in ahead of the rear face: 0.815 and 14.168, 14.985 apart. The rail's own ends on its rows read the same faces (0.824 behind, 14.16 ahead)
Photo 14.99 in ± 0.03 in
Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467, harvested
Scale: its own top rail's 35 teeth at the Picatinny pitch (std.picatinny.slot_pitch), fitted along the photo (rms 0.0006 in). Read by as the right side's, the lens 35.3 in away: the front face 0.773 ahead of the foremost tooth's centre, the rear face 14.220 behind it: 14.993
The maker's figure. Both side photos, read along the rail's own teeth, put its rear face 14.99 in from its front face: the 15 is the body's, without the two tabs.
Width across its side flats (the 3 and 9 o'clock faces)1.59 in ± 0.05 in 40.4 mmCorroboratedPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467
Photo 1.59 in ± 0.05 in used
Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467, harvested
Scale: the lens's distance from the rail's own width: read along the rail's teeth at each height below their tops, the middle windows' near and far ends put the plane of the teeth's near sides 0.0099 to 0.0127 of the lens's distance off the rail's middle, growing by 0.0309 per inch of depth (a 45.7 degree bevel) and levelling off at 0.01258 where the rail is widest: .835 / 2 (std.picatinny.top_width) over 0.01258 is 33.2 in. Read by eight windows, each end at the 50% level, fitted with the slots 40 mm apart (std.mlok.slot_pitch): near ends spread by 1.01343, far ones drawn in by 0.96601 (rms 0.0009 in; the same to 0.00004 along the teeth at twelve heights): the walls 0.02395 of the lens's distance either side of the middle, 0.795 in. The lens's foot comes out at the same place from the windows (6.226 in ahead of the rearmost tooth) and from the teeth's end faces (6.218). ± is the lens's distance (the widest row is one pixel deep) and the left side's reading
Photo 1.63 in ± 0.05 in
Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467, harvested
Scale: as the right side's: the teeth's near sides 0.0095 to 0.0119 of the lens's distance off the middle, by 0.0293 per inch of depth (45.9 degrees), level at 0.01182 over three rows: 35.3 in. Read by as the right side's: near ends spread by 1.01315, far ones drawn in by 0.96754 (rms 0.0008 in): the walls 0.02303 of the lens's distance off the middle, 0.813 in
The photo the outline is traced from; the other side's reading agrees within what either carries, and the faces' edges and the bottom's depth say the same octagon.
Not published, and no view down its length is on file. Read from each side photo by itself: a window in the middle row shows white where a ray passes the near wall's slot and the far wall's, so one end of each window is a slot's end on the near wall and the other on the far wall. Read along the rail's teeth the near ends are spread about the lens's foot by (D - rail) / (D - wall) and the far ones drawn in by (D - rail) / (D + wall): the two walls' distance over the lens's. Two other readings say the same: the edge between a side flat and a diagonal face stands 0.29 from the bore's level (side_flat_half_height), which with the diagonals 0.775 out puts the flats 0.81 out; and the bottom and the diagonals stand 0.76 to 0.78 out. It is close to a regular octagon, a little wider than it is deep.
Height (its rail's top to its bottom flat; the clamp's block hangs 0.37 in below)1.96 in ± 0.02 in 49.8 mmCorroboratedPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467
Photo 1.96 in ± 0.02 in used
Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467, harvested
Scale: its own rail's pitch at the photo's middle (std.picatinny.slot_pitch): 50.90 px a tooth, 129.2 px/in in the rail's mid-plane. Read by the photo levelled by its three rows of windows (1.121 degrees); the webs' brightness steps from white at the tooth tops (row 597.60) and to white at the bottom (row 853.36) 255.8 px apart: 1.980 in, less 0.02 for the bottom flat's near edge
Photo 1.97 in ± 0.02 in
Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467, harvested
Scale: its own rail's pitch at the photo's middle: 50.69 px a tooth, 128.6 px/in. Read by as the right side's (levelled by 0.754 degrees): rows 582.88 and 839.08, 256.2 px, 1.992 in, less 0.02
The photo the outline is traced from; the other side reads 0.01 more, within either's ±.
Not published. A side view's silhouette is the near edge of the bottom flat, which a lens 33 in away and an inch or so above the bore reads 0.02 in low (0.03 if the lens stood two inches above it: its height isn't pinned): taken off.
Inside diameter1.35 in ± 0.005 in 34.3 mmConfirmedPublished: Primary Arms, Expo Arms Free Float AR-15 Handguard - M-LOK - 15" (XP-GUARD15-BLK), Specifications, the maker, read Oct 5, 2026
Published “Inner Diameter 1.35 in.” used
Primary Arms, Expo Arms Free Float AR-15 Handguard - M-LOK - 15" (XP-GUARD15-BLK), Specifications, the maker, read Oct 5, 2026 the page, harvested Oct 5, 2026
The page's figure, drawn as a round bore. Inside the faces the photos give, it leaves walls 0.085 to 0.12 in thick at the slots, which is what shows in the diagonal rows' slots (wall_at_slots). The three-quarter photos show flats inside behind the rows and ribs between them: not measured.
Its rear face against the receiver's front face (negative: behind it)-0.445 in ± 0.01 in -11.3 mmConfirmedWorked out: 0in - {std.ar15.upper_barrel_thread_length}
Worked out -0.445 in ± 0.01 in used
0in - {std.ar15.upper_barrel_thread_length}, harvested
No photo of it mounted is on file, and Primary Arms publishes no instructions for it. Taken to seat against the receiver's front shoulder, where the barrel-nut thread begins (std.ar15.upper_barrel_thread_length: "A barrel nut and a free-float handguard's rear end come back to that shoulder"). A buyer on its page says it is made to: "the hand-guard did not sit flush with the upper receiver, so the locking key did not sit into the groove of the barrel nut as intended ... I filed the dust cover pin down. That allowed the handguard to sit flush and for the locking key to fully seat in the barrel nut" (Pikamon, 2/26/2025, https://www.primaryarms.com/expo-arms-m-lok-handguard-black-15). A buyer's words, not the maker's.
Its two anti-rotation tabs: how far they reach behind its rear face0.19 in ± 0.02 in 4.8 mmCorroboratedPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467
Photo 0.19 in ± 0.02 in used
Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467, harvested
Scale: its own top rail's 35 teeth at the Picatinny pitch (std.picatinny.slot_pitch), fitted along the photo; the lens 33.2 in away. Read by the tab's tip 1.031 behind the rearmost tooth's centre as the teeth read it, 1.010 at its own depth (taken 0.45 in off the middle): 0.195 behind the rear face at 0.815
Photo 0.19 in ± 0.02 in
Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467, harvested
Scale: its own top rail's 35 teeth at the Picatinny pitch, fitted along the photo; the lens 35.3 in away. Read by the other tab, as the right side's: 0.193 behind the rear face
The two tabs read the same; the right side's photo is the one traced.
Primary Arms: "anti-rotation tabs for a strong lock-up on any Mil-Spec receiver". One shows on each side photo, just under the rail's neck: its top edge level, its end square, its underside sloped up to the end (tab_top_above_bore and the two below it).
A tab's top edge above the bore axis0.71 in ± 0.02 in 18 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467
Photo 0.71 in ± 0.02 in used
Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467, harvested
Scale: each photo's own rail pitch at its middle (std.picatinny.slot_pitch): 129.2 and 128.6 px/in; the bore's level its middle row of windows. Read by the silhouette's rear end row by row on the levelled photos: it steps back to the tab's end between 0.721 and 0.698 in above the middle row on the right side, 0.728 and 0.705 on the left
A tab's end, its lower corner above the bore axis0.56 in ± 0.02 in 14.2 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467
Photo 0.56 in ± 0.02 in used
Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467, harvested
Scale: each photo's own rail pitch at its middle (std.picatinny.slot_pitch): 129.2 and 128.6 px/in; the bore's level its middle row of windows. Read by the tab's end is square down to 0.559 in above the middle row on the right side, 0.565 on the left; below that its underside slopes forward
A tab's underside where it meets the rear face, above the bore axis0.47 in ± 0.02 in 11.9 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467
Photo 0.47 in ± 0.02 in used
Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467, harvested
Scale: each photo's own rail pitch at its middle (std.picatinny.slot_pitch): 129.2 and 128.6 px/in; the bore's level its middle row of windows. Read by the sloped underside runs into the rear end's own edge 0.466 in above the middle row on the right side, 0.472 on the left
The outline's rear end (its two tabs' ends) against the receiver's front face (negative: behind it)-0.635 in ± 0.03 in -16.1 mmCorroboratedWorked out: {.rear_face_x} - {.tab_length}
Worked out -0.635 in ± 0.03 in used
{.rear_face_x} - {.tab_length}, harvested
Overall length, the tabs' ends to the front face15.18 in ± 0.03 in 385.6 mmCorroboratedPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467
Photo 15.18 in ± 0.03 in used
Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467, harvested
Scale: its own top rail's 35 teeth at the Picatinny pitch (std.picatinny.slot_pitch), fitted along the photo; the lens 33.2 in away. Read by the tab's tip 1.010 behind the rearmost tooth's centre and the front face 14.168 ahead of it, each at its own depth: 15.178
Photo 15.19 in ± 0.03 in
Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467, harvested
Scale: its own top rail's 35 teeth at the Picatinny pitch, fitted along the photo; the lens 35.3 in away. Read by as the right side's: 15.186
The photo the outline is traced from; the other side reads 0.01 more.
Its rail's top above the bore axis1.2 in ± 0.02 in 30.5 mmCorroboratedPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467
Photo 1.2 in ± 0.02 in used
Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467, harvested
Scale: its own rail's pitch at the photo's middle (std.picatinny.slot_pitch): 129.2 px/in in the rail's mid-plane. Read by the middle row's eight windows' centres (row 752.17; each window's top and bottom at the 50% level, on the levelled photo) 154.6 px below the step at the tooth tops (row 597.60): 1.197 in
Photo 1.2 in ± 0.02 in
Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467, harvested
Scale: its own rail's pitch at the photo's middle: 128.6 px/in. Read by as the right side's: rows 737.67 and 582.88, 154.8 px, 1.203 in
Both sides read 1.20.
The bore's level is taken as its middle row of M-LOK slots' (its 3 and 9 o'clock faces): the photos have no bore in them. A mil-spec flat-top receiver's rail stands the same height above its bore (Aero's M4E1 Threaded upper, from its own photos: 2.09 above the pins less the bore's .8775 is 1.2125), so with the handguard about the bore the two rails are level. No page on file says that they are.
Its bottom flat below the bore axis0.76 in ± 0.03 in 19.3 mmCorroboratedWorked out: {.height} - {.rail_top_above_bore}
Worked out 0.76 in ± 0.03 in used
{.height} - {.rail_top_above_bore}, harvested
Its four diagonal faces: how far each stands from the bore axis0.775 in ± 0.02 in 19.7 mmCorroboratedPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467
Photo 0.775 in ± 0.02 in used
Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467, harvested
Scale: its own rail's pitch at the photo's middle (std.picatinny.slot_pitch): 129.2 px/in in the rail's mid-plane. Read by the upper and lower rows' windows' centres 0.504 in above and 0.510 below the middle row's (rows 687.02, 752.17 and 818.02 on the levelled photo): 0.507 either side. A slot through a wall standing at 45 degrees shows open only where the ray clears both of the wall's faces, so each window's centre is nearer the bore's level than its slot's by 0.354 of the wall's thickness (0.11, wall_at_slots): the slots 0.547 off the bore's level, and on the 45 degree lines that is 0.774 from the axis
Photo 0.778 in ± 0.02 in
Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467, harvested
Scale: its own rail's pitch at the photo's middle: 128.6 px/in. Read by as the right side's: 0.507 above and 0.512 below the middle row's (rows 672.46, 737.67 and 803.59), 0.510 either side, the slots 0.550 off the bore's level
The photo the outline is traced from; the other side reads 0.003 more.
The faces are taken at 45 degrees, their slots on the lines through the bore at 45 degrees ("Full M-LOK compatibility (7 sides)"): then the edge between a side flat and a diagonal comes out 0.30 from the bore's level, and the photos show it at 0.29 (side_flat_half_height).
A side flat's upper and lower edges, each from the bore's level (a check on the section)0.29 in ± 0.02 in 7.4 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467
Photo 0.29 in ± 0.02 in used
Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467, harvested
Scale: each photo's own rail pitch at its middle (std.picatinny.slot_pitch): 129.2 and 128.6 px/in. Read by where the webs between the slots step in brightness: the upper edge 0.283 and 0.272 in above the middle row of windows on the two photos (0.277), the lower in several steps 0.29 to 0.36 below it (0.32: the edge is broken); both are on the corner nearest the lens, 0.8 in off the middle, which reads 2.5% large about the lens's height (about an inch above the bore): 0.295 above and 0.288 below. The same handguard in FDE (b73e40fcdf82, bb47fb7d2cad), where the edges show as lines, has the upper one 0.30 above its middle row
Not built from: the section's own corner is where the side flat (width / 2) meets the 45 degree face (diagonal_face_distance), 0.30 from the bore's level.
The wall's thickness at the slots, as it shows in the diagonal rows (a check on the bore)0.11 in ± 0.02 in 2.8 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467
Photo 0.11 in ± 0.02 in used
Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467, harvested
Scale: each photo's own rail pitch at its middle (std.picatinny.slot_pitch); the slots taken 7 mm wide (std.mlok.slot_width). Read by a 7 mm slot through a wall standing at 45 degrees shows 0.707 x (7 mm - the wall) open, a little more in the upper row and less in the lower as the lens stands above the bore: the upper rows' windows are 0.132 and 0.124 in high, the lower 0.098 and 0.096, which is a wall of 0.107 and 0.114
Not built from. The published 1.35 in bore inside the photos' faces leaves 0.12 at the side flats' middles, 0.10 at the diagonals' and 0.085 at the bottom's.
Where the upper diagonal faces end under the rail's neck, above the bore axis0.73 in ± 0.03 in 18.5 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467
Photo 0.73 in ± 0.03 in used
Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467, harvested
Scale: each photo's own rail pitch at its middle (std.picatinny.slot_pitch): 129.2 and 128.6 px/in. Read by the webs' brightness steps from the lit neck to the dark face 0.749 in above the middle row of windows on both photos; on the same handguard in FDE (b73e40fcdf82, bb47fb7d2cad) the line is 0.729 and 0.723 above it. Between the two; ± covers both
Its rail's top flat, side to side0.64 in ± 0.03 in 16.3 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467
Photo 0.64 in ± 0.03 in used
Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467, harvested
Scale: the rail's own widest width, .835 (std.picatinny.top_width), which sets the lens's distance in each photo (33.2 and 35.3 in). Read by the plane of the teeth's near sides at each height below their tops, as the middle windows read through them (width's method): a straight line from 0.0097 (0.0091) of the lens's distance at the top, twice which is 0.641 in on both photos
The rail's profile as the side photos' teeth give it: a flat, 45 degree bevels down to the widest (.835, std.picatinny.top_width), which the slots' floors (std.picatinny.slot_depth) just pass. A reading, and since 2026-10-12 not what the rail is drawn by: its head is the standard's in section (std.picatinny.*, pipeline/blender/lib.py rail_head), a flat .656 across and the widest from .0895 to .1105 under the top, which this reading and rail_widest_below_top are within their ± (the builder refuses to run if they stop being). Drawn as the two readings alone the faces met sharp at the widest, 0.009 in inside the standard's above it and 0.010 below: a gap each side of every clamp.
Its rail's widest line below its top0.1 in ± 0.01 in 2.5 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467
Photo 0.1 in ± 0.01 in used
Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467, harvested
Scale: each photo's own rail pitch at its middle (std.picatinny.slot_pitch): 129.2 and 128.6 px/in. Read by the height at which the teeth's near sides stop moving out with depth: between the rows 0.093 and 0.108 in below the tooth tops (left side), 0.085 and 0.116 (right); the flat and the 45 degree bevels reach .835 at 0.097
Where its rail's underside ends on the neck, below its top0.21 in ± 0.01 in 5.3 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467
Photo 0.21 in ± 0.01 in used
Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467, harvested
Scale: each photo's own rail pitch at its middle (std.picatinny.slot_pitch): 129.2 and 128.6 px/in. Read by under the teeth the webs are in shadow down to a step up in brightness (rows 624.18 and 609.41 on the levelled photos), 0.206 in below the step at the tooth tops on both; on the same handguard in FDE (b73e40fcdf82, bb47fb7d2cad) 0.214 and 0.224
From the rail's widest line the underside comes back in to the neck; taken at the standard's 45 degrees from the standard's widest (since 2026-10-12: its lower faces carried on to this height), which makes the neck 0.64 in wide under the rail (0.62 while the faces were drawn meeting sharp at rail_widest_below_top). From there the neck's sides are run straight to where the upper diagonal faces end (neck_bottom_above_bore).
Its rail's rearmost slot (its centre) ahead of its rear face0.62 in ± 0.02 in 15.7 mmCorroboratedPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467
Photo 0.62 in ± 0.02 in used
Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467, harvested
Scale: its own top rail's 35 teeth at the Picatinny pitch (std.picatinny.slot_pitch), fitted along the photo. Read by the rear land's front edge and the rearmost tooth's rear edge (0.312 and 0.089 behind that tooth's centre): the slot between them centred 0.200 behind it, half a pitch as every other is; the rear face 0.82 behind it (the rail's own end 0.824, the side face's edge 0.815)
Photo 0.627 in ± 0.02 in
Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467, harvested
Scale: its own top rail's 35 teeth at the Picatinny pitch, fitted along the photo. Read by as the right side's: the rear face 14.220 behind the foremost tooth's centre, the rearmost slot 13.593
The photo the outline is traced from; the other side reads 0.007 more.
The rail begins with a land 0.50 in long and ends with one 0.46 in long, its top edge chamfered (rail_front_chamfer); between them 36 slots, wider than the standard's (0.222 against .206 +.008: its teeth are 0.172 long). The model cuts them at the standard's width.
Slots in its top rail36ProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467
Photo 36 count used
Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467, harvested
Scale: none: a count. Read by 35 teeth between the two end lands on each photo, every one 49.8 to 51.1 px from the next: 36 slots
The rearmost M-LOK slot's centre ahead of its rear face (every row)2.935 in ± 0.02 in 74.5 mmCorroboratedPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467
Photo 2.935 in ± 0.02 in used
Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467, harvested
Scale: its own top rail's 35 teeth at the Picatinny pitch (std.picatinny.slot_pitch), fitted along the photo; the slots 40 mm apart (std.mlok.slot_pitch). Read by the middle row's eight windows fitted as near and far slot ends about the lens's foot (width's method): the rearmost slot's centre 2.115 ahead of the rearmost tooth's centre at its own depth (rms 0.0009 in), the rear face 0.82 behind it; the upper and lower rows 2.113 and 2.116
Photo 2.937 in ± 0.02 in
Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467, harvested
Scale: its own top rail's 35 teeth at the Picatinny pitch, fitted along the photo; the slots 40 mm apart. Read by as the right side's: the foremost slot's centre 0.2587 behind the foremost tooth's (0.2590 and 0.2589 in the other rows), 1.032 behind the front face; seven pitches back from it in a body 14.993 long
The photo the outline is traced from; the other side's rows are within 0.002 of it.
The three rows a side photo shows are in step (their rearmost slots within 0.003 in of each other), and the two sides mirror each other (the foremost slot 1.026 and 1.032 behind the front face). The slots read 1.28 in long, the standard's 32 mm within its ± 1.
The rearmost M-LOK slot's centre ahead of the receiver's front face2.49 in ± 0.03 in 63.2 mmCorroboratedWorked out: {.rear_face_x} + {.mlok_slot0_from_rear_face}
Worked out 2.49 in ± 0.03 in used
{.rear_face_x} + {.mlok_slot0_from_rear_face}, harvested
M-LOK slots in each row8ProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467
Photo 8 count used
Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467, harvested
Scale: none: a count. Read by eight windows in each of the three rows on each photo
Three rows show on each side (the upper diagonal, the side, the lower diagonal); the bottom's row shows only edge-on in the three-quarter photos and is taken to be the same eight (Primary Arms: "Full M-LOK compatibility (7 sides)").
The room inside its faces, from the face in to the barrel (what an M-LOK accessory's nuts may take)No value yetMissingNo source yet
Not sourced: what runs under it is another part (a barrel, a gas block, a gas tube), so the room is the build's and not this part's.
The channel in its top, under the rail (the gas tube's), side to side0.45 in ± 0.07 in 11.4 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photo _00: three-quarter view from the front right, 2200 x 1467
Photo 0.45 in ± 0.07 in used
Primary Arms' gallery for XP-GUARD15-BLK, photo _00: three-quarter view from the front right, 2200 x 1467, harvested
Scale: the rail's own widest width in the same plane, the front face: .835 (std.picatinny.top_width) between its two widest corners, 62 px across and 30 up. Read by the channel's two edges 33 px apart on one row of the front face, against the rail's width run the same way across that face (71.8 px/in along a row, the face's upright edges leaning 0.07): 0.46 in. Corners picked by eye to 3 px on a brightened crop: ± 0.07
A keyhole: the bore opens upward into a channel with a round roof. Its roof isn't measured: drawn round about the gas tube's standard height (std.ar15.gas_tube_above_bore).
The clamp's rearmost cross bolt, its axis ahead of the rear face0.5 in ± 0.03 in 12.7 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467
Photo 0.5 in ± 0.03 in used
Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467, harvested
Scale: each photo's own top rail's 35 teeth at the Picatinny pitch (std.picatinny.slot_pitch), fitted along it. Read by circles found on the bolts' ends (Hough): 0.492 ahead of the rear face on the right side, 0.511 on the left (its head)
Three cross bolts through the block under its rear end: socket heads on the left, and on the right two screw ends either side of a steel nut with a pointed top. A buyer on its page: "5mm Allen Key for the screws" (Pikamon, 2/26/2025); another has Primary Arms' torque for them: "the cross bolts are 20-25 in-lbs and recommended with blue threadlocker" (Kye, 10/11/2024).
The clamp's cross bolts, axis to axis0.5 in ± 0.02 in 12.7 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467
Photo 0.5 in ± 0.02 in used
Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467, harvested
Scale: each photo's own top rail's 35 teeth at the Picatinny pitch (std.picatinny.slot_pitch), fitted along it. Read by the outer two 0.994 apart on the right side (0.492, 1.486) and 1.010 on the left (0.511, 1.521), the middle one halfway (0.997 on the left)
The clamp's cross bolts, their axes below the bore axis0.94 in ± 0.03 in 23.9 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467
Photo 0.94 in ± 0.03 in used
Primary Arms' gallery for XP-GUARD15-BLK, photos _01 and _02: its two sides on white, 2200 x 1467, harvested
Scale: each photo's own rail pitch at its middle (std.picatinny.slot_pitch); the bore's level its middle row of windows. Read by circles found on them (Hough): the bolts' ends 0.967 in below the middle row of windows on the right side, their heads 0.911, 0.918 and 0.957 on the left
A cross bolt's head (the left side)0.3 in ± 0.03 in 7.6 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467
Photo 0.3 in ± 0.03 in used
Primary Arms' gallery for XP-GUARD15-BLK, photo _02: its left side on white, the receiver's end at the right, 2200 x 1467, harvested
Scale: its own rail's pitch at the photo's middle (std.picatinny.slot_pitch): 129.4 px/in. Read by circles found on the three heads (Hough): 0.294, 0.328 and 0.277 in across
A cross bolt's threaded end (the right side)0.19 in ± 0.03 in 4.8 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467
Photo 0.19 in ± 0.03 in used
Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467, harvested
Scale: its own rail's pitch at the photo's middle (std.picatinny.slot_pitch): 129.6 px/in. Read by circles found on the two screw ends (Hough): 0.170 and 0.213 in across
The clamp's steel nut on the right side: its round, about the middle bolt0.44 in ± 0.02 in 11.2 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-FDE, photo _01: the same handguard in FDE Cerakote, its right side on white, 2200 x 1467
Photo 0.44 in ± 0.02 in used
Primary Arms' gallery for XP-GUARD15-FDE, photo _01: the same handguard in FDE Cerakote, its right side on white, 2200 x 1467, harvested
Scale: that photo's own rail pitch at its middle (std.picatinny.slot_pitch): 49.04 px a tooth, 124.5 px/in in the rail's mid-plane, 1% more at the block's face. Read by the black shape's widest rows on the levelled photo (rows 847 to 859): 55 and 56 px across, 0.437 and 0.445 in; they are 0.95 in below the middle row of windows, the cross bolts' level
A buyer on its page calls it "the locking key", which sits "into the groove of the barrel nut" (Pikamon, 2/26/2025). Black on the FDE handguard, so its outline is read there: a round about the middle bolt, and above it a neck that tapers to a blunt point on the lower diagonal face (the three entries below). On the black handguard's photo only a ring 0.32 in across shows inside it.
The clamp's nut: its point above the middle bolt's axis0.375 in ± 0.02 in 9.5 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-FDE, photo _01: the same handguard in FDE Cerakote, its right side on white, 2200 x 1467
Photo 0.375 in ± 0.02 in used
Primary Arms' gallery for XP-GUARD15-FDE, photo _01: the same handguard in FDE Cerakote, its right side on white, 2200 x 1467, harvested
Scale: that photo's own rail pitch at its middle (std.picatinny.slot_pitch): 49.04 px a tooth, 124.5 px/in in the rail's mid-plane, 1% more at the block's face. Read by the black shape's top row (808) is 0.583 in below the middle row of windows, its widest rows 0.955: 0.372 apart
The clamp's nut: where its neck's straight sides end under the point, above the middle bolt's axis0.34 in ± 0.02 in 8.6 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-FDE, photo _01: the same handguard in FDE Cerakote, its right side on white, 2200 x 1467
Photo 0.34 in ± 0.02 in used
Primary Arms' gallery for XP-GUARD15-FDE, photo _01: the same handguard in FDE Cerakote, its right side on white, 2200 x 1467, harvested
Scale: that photo's own rail pitch at its middle (std.picatinny.slot_pitch): 49.04 px a tooth, 124.5 px/in in the rail's mid-plane, 1% more at the block's face. Read by row by row the neck narrows evenly (0.334 in wide 0.18 above the bolts' level, 0.270 at 0.25, 0.230 at 0.30, 0.207 at 0.32) and then closes within 0.05 in: the even taper ends about 0.34 above
The clamp's nut: its neck's width where the straight sides end0.2 in ± 0.03 in 5.1 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-FDE, photo _01: the same handguard in FDE Cerakote, its right side on white, 2200 x 1467
Photo 0.2 in ± 0.03 in used
Primary Arms' gallery for XP-GUARD15-FDE, photo _01: the same handguard in FDE Cerakote, its right side on white, 2200 x 1467, harvested
Scale: that photo's own rail pitch at its middle (std.picatinny.slot_pitch): 49.04 px a tooth, 124.5 px/in in the rail's mid-plane, 1% more at the block's face. Read by the black shape is 0.207 in wide 0.32 above the bolts' level and 0.167 at 0.35
The neck's sides run straight from the round's widest points to here: that line is 0.315 in wide 0.18 above the bolts' level, 0.263 at 0.25 and 0.229 at 0.30, where the photo has 0.334, 0.270 and 0.230.
The chamfer on its rail's front end (the top edge of the front land)0.11 in ± 0.02 in 2.8 mmProvisionalPhoto: Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467
Photo 0.11 in ± 0.02 in used
Primary Arms' gallery for XP-GUARD15-BLK, photo _01: the handguard's right side on white, the receiver's end at the left, 2200 x 1467, harvested
Scale: its own top rail's 35 teeth at the Picatinny pitch (std.picatinny.slot_pitch), fitted along the photo. Read by the silhouette's front end row by row: 14.078 ahead of the rearmost tooth's centre 0.023 in below the tooth tops, 14.114, 14.137, 14.156 and 14.170 by 0.116 below, where it is the front face; the left side's photo (c3d5763fef0d) has 0.07 back over 0.07 down
Taken at 45 degrees: the photo gives 0.11 back for 0.116 down. The rear end's is a fifth of it (0.02) and is left to the edges' break.
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Handguard mount
Picatinny rail (MIL-STD-1913)
- Red dot mounts
- Aimpoint Duty RDS One-piece TNP Mount, 30 mm, Aimpoint LRP (Lever Release Picatinny) Mount with 39 mm Spacer, for Micro, Aimpoint One-piece Torsion Nut Mount and Spacer, 39 mm, Geissele Super Precision T1 Mount - 1.93" Height, Geissele Super Precision T1 Mount - Absolute Co-Witness, Geissele Super Precision T1 Mount - Lower 1/3 Co-Witness, Holosun 1.63 in lower 1/3 co-witness pedestal mount (HS-MOUNT-AR-RISER-ARO), Midwest Industries MK2 QD T2 Aimpoint Mount, Low, Midwest Industries MK2 QD T2 Aimpoint Mount, Lower 1/3 Cowitness, Midwest Industries MK2 QD T2 Aimpoint Mount, NV 2.26 in Height, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – 1.93″ HEIGHT, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – LOWER 1/3 (39MM HEIGHT), Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.42 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.57 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.93 in, Scalarworks LEAP/02 Aimpoint Micro T-2 quick-detach mount, 2.26 in, SIG Sauer M1913 I-BEAM Mount, 1.41 in absolute co-witness, SIG Sauer See-Through Riser Mount, 1.41 in absolute co-witness, Unity Tactical FAST Micro Mount, 2.26 in optical centerline
- Optics
- Aimpoint Patrol Rifle Optic (PRO) Red Dot Reflex Sight - QRP2 Mount, EOTECH HWS EXPS3 holographic weapon sight, 1-Dot Speed Ring, Holosun HS510C Open Reflex MRS Solar QD Mount
- Lights
- Olight Baldr S BL, Streamlight ProTac Rail Mount HL-X, SureFire Mini Scout Light Pro, SureFire Scout Light Pro Dual Fuel
- Backup sights
- Daniel Defense A1.5 Fixed Rear Sight, Daniel Defense Rail Mounted Fixed Front Sight, Magpul MBUS 3 Sight – Front, Magpul MBUS 3 Sight – Rear, Magpul MBUS Pro Sight – Front, Magpul MBUS Pro Sight – Rear
- Magnifiers
- EOTECH G33 Magnifier, STS Mount, EOTECH G45 Magnifier, STS Mount, Holosun HM3X 3× magnifier with flip mount
- Scope mounts
- Primary Arms Deluxe AR-15 Scope Mount - 30mm, Primary Arms SLx Cantilever 30mm Mount - 1.5", Reptilia AUS™ MOUNT - 30MM DIAMETER - 39MM HEIGHT, Scalarworks LEAP/08 quick-detach scope mount, 30 mm, 1.57 in, SIG SAUER ALPHA-MSR scope mount, 30 mm, Vortex Sport Cantilever 30mm Mount
M-LOK
- Hand stops
- BCM KAG (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK Hand Stop (fit unchecked), Magpul M-LOK Index Panel (fit unchecked)
- Vertical grips
- BCM Vertical Grip Mod 3 (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK MVG vertical grip (fit unchecked)
- Lights
- Cloud Defensive REIN (fit unchecked), Streamlight ProTac Rail Mount HL-X (fit unchecked), SureFire Mini Scout Light Pro (fit unchecked), SureFire Scout Light Pro Dual Fuel (fit unchecked)
- Rail sections
- Magpul M-LOK® Aluminum Rail, 3 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 5 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 7 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 9 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 11 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 3 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 5 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 7 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 9 Slots (fit unchecked)
- Adapter plates
- Magpul M-LOK Hand Stop MOE Adapter (fit unchecked)
- Sling mounts
- Magpul M-LOK QD Sling Mount (fit unchecked)
- Rail covers
- Magpul M-LOK Rail Cover Type 2 (fit unchecked)
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Primary Arms $99.99 Black (hardcoat anodized) Nov 21, 2026, in stock that day
- Primary Arms $119.99 FDE (Cerakote) Nov 21, 2026, in stock that day