Red dot mount
Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.93 in
Scalarworks' quick-detach mount for an Aimpoint Micro T-2 and the dots cut for its footprint, the dot's axis 1.93 in over the rail ("Optic center height over rail ... SW0120 : 1.93"", "Co-Witness ... SW0120 : Only with 1.93" PEAK/02": the maker's own taller backup sights). A frame of 7075 with a window through its sides and its ends, leaning forward over its clamp ("Forward lean for additional magnifier space", Primary Arms), clamped by one knurled wheel on the left turned by hand ("Close clamp by turning ClickDrive wheel as tightly as you can by hand (Do not use tools)."). 51 g.

- Weight
- 1.8 oz Conflictpublished: Scalarworks, LEAP/01 (product page, SPECIFICATIONS), the maker, read Nov 3, 2026Its sources span 1.65 oz to 1.82 oz.
- Lowest price
- $159.00 at Scalarworks, read Nov 21, 2026 (Black)
- Maker's number
- SW0120
- Colour
- Black (placeholder)
- Drawn as
- modelled
- Maker's page
- scalarworks.com
In “22RB .22 LR rifle”, a build on the start page, in place of its Holosun 1.63 in lower 1/3 co-witness pedestal mount (HS-MOUNT-AR-RISER-ARO).
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Optical axis above the rail's top, with an Aimpoint Micro T-2 on it (the maker's height)1.93 in 49 mmConfirmedPublished: Scalarworks, LEAP/01 (product page, SPECIFICATIONS), the maker, read Nov 3, 2026
Published “Optic center height over rail SW0100 : 1.42" SW0110 : 1.57" SW0120 : 1.93"” used
Scalarworks, LEAP/01 (product page, SPECIFICATIONS), the maker, read Nov 3, 2026 the page, harvested Nov 3, 2026
MidwayUSA's page: "Note: Height measurement is from the top of the rail to the center of the optic."
Published “1.93” OPTIC CENTER”
Scalarworks, the technical drawing of SW0120 in the LEAP/01 page's gallery for the 1.93 in height (a copy on file), the maker, read Nov 3, 2026 the page, harvested Nov 3, 2026
From the extension line through the clamp's shaft (the rail's top) to the T-2's axis.
Photo 1.921 in ± 0.006 in
Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders. Read by the red dot's centroid (row 437.0) above the extension line (row 1091): 654 px
0.009 in under the stated figure: the 1.93 in's own lines (654 px) are at 338.9 px/in, half a percent off the scale the rail and the 29.8 mm agree on.
The maker's stated centre height, the figure a buyer compares and the category's; its drawing's lines put the axis 0.009 in lower at the scale its rail gives, inside the two readings' ±.
The maker names no dot in the sentence ("Optic center height over rail"); the page is "LEAP/01 Premium Aimpoint Micro T-2 mounts." and its drawing of this height draws a T-2 on the mount: the height is the T-2's. Its co-witness, in the same table: "SW0120 : Only with 1.93" PEAK/02" (the maker's own taller backup sights). The page's advice: "Choose 1.93″ height if: You value a more relaxed heads-up shooting style. You are willing to upgrade to 1.93″ PEAK/02 BUIS. You shoot with a top-rail mounted light or laser."
Top of the window through the mount (end to end), above the rail's top1.173 in 29.8 mmConfirmedPublished: Scalarworks, the technical drawing of SW0120 in the LEAP/01 page's gallery for the 1.93 in height (a copy on file), the maker, read Nov 3, 2026
Published “29.8MM” used
Scalarworks, the technical drawing of SW0120 in the LEAP/01 page's gallery for the 1.93 in height (a copy on file), the maker, read Nov 3, 2026 the page, harvested Nov 3, 2026
From the same extension line as the 1.93 in to the top of the window's throat (the inner of the two outlines drawn round it).
Photo 1.1766 in ± 0.006 in
Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders. Read by the throat's top stroke (row 690.5) above the extension line (1091): 400.5 px
29.89 mm: the check of the drawing's scale.
The maker's stated dimension; its lines read the same at the scale the rail gives.
The drawings' window figures don't step as the heights do (17.5, 21.5 and 29.8 mm for 1.42, 1.57 and 1.93 in): in this height the deck over the window is 0.029 in (0.75 mm) thicker than in the 1.57 in's drawing (the floor 49 px over the window's throat here, 39 px there), while the floors step by 0.356 in for the stated 0.36 and the T-2 stands 0.601 in over its floor here and 0.604 in there. The deck's floor is read on the drawing, not worked out from the window.
The deck's floor (where the dot's base sits) above the rail's top1.341 in ± 0.037 in 34.1 mmProvisionalWorked out: {.optical_axis_above_rail} - {aimpoint-micro-t-2.axis_above_base}
Worked out 1.341 in ± 0.037 in used
{.optical_axis_above_rail} - {aimpoint-micro-t-2.axis_above_base}, harvested
1.93 in less the T-2's 0.589 in.
Photo 1.3205 in ± 0.006 in
Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders. Read by the stroke the T-2's foot stands on between the rims (row 641.5) above the extension line (1091): 449.5 px. The T-2's axis is 204.5 px over it: 0.601 in, inside the 0.589 ± 0.037 the T-2's ledger has
The category's figure: the maker's axis height for the T-2 less the T-2's own axis over its base, which puts the T-2 at the maker's 1.93 in. The maker's drawing has the floor 0.02 in lower, inside the two readings' ±.
A floor between two rims that run the deck's whole length, the T-2's foot down on it between them and its housing on the rims' tops (the drawing; the deck from above in Wing Tactical's photo of a LEAP/01, filed with the 1.57 in). The maker states only the axis's height, for the T-2: the floor is that less the T-2's axis over its base. The drawing puts it there within the two readings' ±.
The deck's two rims, their tops above the rail's top1.398 in ± 0.006 in 35.5 mmCorroboratedPhoto: Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 1.398 in ± 0.006 in used
Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders. Read by the rims' top stroke (row 615) above the extension line (1091): 476 px
Photo 1.416 in ± 0.015 in
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level). Read by the mount's top edge (row 348, from column 300 to 717) above the teeth's tops: 349.5 px
1.3% over the drawing, as the 1.57 in's photo is: the near face stands nearer the lens than the rail's middle.
The maker's drawing at the scale its rail gives; the photo reads the near face 1.3% large.
What the side views show as the mount's top. Not drawn above the deck's floor: every Micro dot on file is drawn with its base as wide as its housing (the part's approximations).
The footprint's middle along the deck, ahead of the wheel's shaft0.364 in ± 0.05 in 9.2 mmCorroboratedPhoto: Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200
Photo 0.364 in ± 0.05 in used
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level). Read by the middle of the rims' flat top, between the step at its front end (column 300) and where its rear end scoops down (717): column 508.5, 89.75 px ahead of the wheel's shaft (column 598.25, the slot midway)
Photo 0.41 in ± 0.06 in
Scalarworks, scalarworks-leap-01-aimpoint-micro-t2-bundle-1.93-side-SW0120-T2.jpg: the mount with a Micro T-2 on it, straight left side, harvested
Scale: the rail section's slots at columns 333.0 and 868.5, six pitches apart: 89.25 px a pitch, 226.5 px/in; the shaft in the slot midway, column 600.75. Read by the T-2's rubber covers, lids closed, from column 162 to 840 at its axis: their middle 0.44 in ahead of the shaft; the T-2's model has its footprint's middle 0.03 in behind its covers' middle
The check: where the T-2 screwed to the footprint has its own footprint's middle.
The mount's own deck; the T-2 on it in the same set-up puts its footprint's middle 0.05 in further forward, within both ±.
Further forward than on the 1.57 in (0.28): the legs lean forward, and the taller mount's deck stands further ahead of its clamp.
The clamp's length along the rail, at its foot1.547 in ± 0.03 in 39.3 mmProvisionalPhoto: Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200
Photo 1.547 in ± 0.03 in used
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level). Read by the clamp's foot under the rail's top (row 758), from the front leg's lower end (column 433.1) to the rear face (815): 381.9 px
The clamp's foot, its front end ahead of the wheel's shaft0.669 in ± 0.02 in 17 mmProvisionalPhoto: Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200
Photo 0.669 in ± 0.02 in used
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level). Read by the traced outline's foot (profiles.side) ends at column 433.1, 165.1 px ahead of the shaft (598.25)
The clamp's foot, its rear end behind the wheel's shaft0.878 in ± 0.02 in 22.3 mmProvisionalPhoto: Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200
Photo 0.878 in ± 0.02 in used
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level). Read by the rear face, column 815, 216.75 px behind the shaft
Overall length along the rail2.198 in ± 0.03 in 55.8 mmProvisionalPhoto: Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200
Photo 2.198 in ± 0.03 in used
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level). Read by the deck's front step (column 272.5) to the rear face (815): 542.5 px
As read: the near face reads about 1.3% large (rim_top_above_rail). No page gives this height's length.
Overall width across the clamp1.334 in ± 0.006 in 33.9 mmProvisionalPhoto: Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 1.334 in ± 0.006 in used
Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders. Read by the clamp's two outer faces, the strokes at columns 373.5 and 827.5 (rows 950 to 1120): 454 px, about column 600.5, the rail's middle
The maker: "the Leap mount is symmetrical, protruding less than 7mm from either side of your Picatinny rail." (under 1.386 in).
The body under the deck, across (its two side walls' outer faces)0.94 in ± 0.006 in 23.9 mmProvisionalPhoto: Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 0.94 in ± 0.006 in used
Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders. Read by the walls' strokes at columns 440.5 and 760.5 (rows 640 to 880): 320 px
The clamp's foot below the rail's top0.234 in ± 0.006 in 5.9 mmCorroboratedPhoto: Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 0.234 in ± 0.006 in used
Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders. Read by the jaws' feet (row 1170.5) under the extension line (1091): 79.5 px
Photo 0.249 in ± 0.012 in
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level). Read by the left jaw's foot (row 759) under the teeth's tops (697.5): 61.5 px
The finer reading; the photo agrees within the two ±.
ClickDrive wheel, over its teeth0.631 in ± 0.015 in 16 mmProvisionalPhoto: Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200
Photo 0.631 in ± 0.015 in used
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level). Read by the teeth's tips 76.5 px above and 79.25 px below the wheel's centre (column 599.5, row 699.5): 155.75 px
The wheel's face is the nearest thing to the lens: as read, perhaps 1.3% large.
Twenty teeth, as on the 1.57 in's (counted on this photo's upper half too: tips about 18 degrees apart).
ClickDrive wheel, at the foot of its teeth0.523 in ± 0.02 in 13.3 mmProvisionalPhoto: Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200
Photo 0.523 in ± 0.02 in used
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level). Read by the valleys between the top teeth, 64.5 px from the centre
ClickDrive wheel, the face inside its rim0.565 in ± 0.015 in 14.4 mmProvisionalPhoto: Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200
Photo 0.565 in ± 0.015 in used
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level). Read by the bright ring round the face, columns 530 to 669.5
ClickDrive wheel, the socket in its middle0.138 in ± 0.015 in 3.5 mmProvisionalPhoto: Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200
Photo 0.138 in ± 0.015 in used
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level). Read by the dark hole at the wheel's middle, columns 582.5 to 616.5
ClickDrive wheel's axis above the rail's top-0.008 in ± 0.008 in -0.2 mmProvisionalPhoto: Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200
Photo -0.008 in ± 0.008 in used
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.93-side-SW0120.jpg: SW0120 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 306.5 and 890.0 (the gaps' edges on rows 700 to 724), six pitches apart (std.picatinny.slot_pitch): 97.25 px a pitch, 246.8 px/in at the rail's middle; the teeth's tops on row 697.5 (the white ground shows through the slots down to their floors: the photo is level). Read by the wheel's centre (row 699.5, its socket's middle) under the teeth's tops (697.5)
On the rail's top within the reading: the shaft half in the slot and half in the clamp's roof.
ClickDrive wheel, its outer face left of the mount's middle0.663 in ± 0.006 in 16.8 mmProvisionalPhoto: Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 0.663 in ± 0.006 in used
Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders. Read by the wheel's knurl drawn edge on under the left jaw's rounded corner, its outer edge at column 374.5, flush with the clamp's left face: 225.75 px from the rail's middle
ClickDrive wheel, across0.167 in ± 0.008 in 4.2 mmProvisionalPhoto: Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 0.167 in ± 0.008 in used
Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders. Read by the knurl drawn edge on, columns 374.5 to 431.5: 57 px
The set screw in the rear end (the ball detent's), left of the middle0.579 in ± 0.008 in 14.7 mmProvisionalPhoto: Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 0.579 in ± 0.008 in used
Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders. Read by the concentric circles drawn low at the left (its centre at column 403, row 1093): 197.25 px left of the rail's middle
"An integrated spring-loaded ball-detent exerts enough force against the crown to make it completely recoil proof." (the maker's page); the screw low in the rear end in Primary Arms' side photo of this height (9aea9c007ed8).
The set screw's hole in the rear end0.106 in ± 0.01 in 2.7 mmProvisionalPhoto: Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 0.106 in ± 0.01 in used
Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders. Read by the outermost of its circles, columns 385 to 421
The telescoping jaw: where it is split from the right wall, right of the middle0.51 in ± 0.012 in 13 mmProvisionalPhoto: Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 0.51 in ± 0.012 in used
Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders. Read by the two strokes up the right wall at columns 770.5 and 777.5 (rows 1025 to 1105): their middle, 173.75 px right of the rail's middle
The telescoping jaw, its top above the rail's top0.195 in ± 0.006 in 5 mmProvisionalPhoto: Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 0.195 in ± 0.006 in used
Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders. Read by the stroke across the right wall (row 1024.5, columns 770 to 828) above the extension line (1091)
The telescoping jaw, where it turns in under the rail's head (its top there, below the rail's top)-0.056 in ± 0.01 in -1.4 mmProvisionalPhoto: Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo -0.056 in ± 0.01 in used
Scalarworks' technical drawing of SW0120: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 29.8 mm's own lines 400.5 px apart (341.4): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. The drawing is the 1.57 in's stroke for stroke from the clamp up to the body's shoulders. Read by the two strokes up the right wall curve in at row 1108 to meet the rail's upper face: 17 px under the extension line, as a height
The guide pins' heads on the jaw's outer face, ahead of and behind the shaft's0.53 in ± 0.05 in 13.5 mmProvisionalWorked out: {scalarworks-leap-02-micro-226.guide_pin_x}
Worked out 0.53 in ± 0.05 in used
{scalarworks-leap-02-micro-226.guide_pin_x}, harvested
No view of this mount's right side is on file: the LEAP/02's (Primary Arms' photo of it from the right front, 4945353b7bdf), on the same ClickDrive clamp, is the only one of the family's.
A guide pin's head0.1 in ± 0.02 in 2.5 mmProvisionalWorked out: {scalarworks-leap-02-micro-226.guide_pin_d}
Worked out 0.1 in ± 0.02 in used
{scalarworks-leap-02-micro-226.guide_pin_d}, harvested
The LEAP/02's, as guide_pin_x.
The shaft's end on the jaw's outer face0.15 in ± 0.02 in 3.8 mmProvisionalWorked out: {scalarworks-leap-02-micro-226.shaft_end_d}
Worked out 0.15 in ± 0.02 in used
{scalarworks-leap-02-micro-226.shaft_end_d}, harvested
The LEAP/02's, as guide_pin_x.
The dark ring round each head in the jaw's face0.008 in ± 0.005 in 0.2 mmProvisionalWorked out: {scalarworks-leap-02-micro-226.head_ring}
Worked out 0.008 in ± 0.005 in used
{scalarworks-leap-02-micro-226.head_ring}, harvested
The LEAP/02's, as guide_pin_x.
How deep each head's hole is drawn0.04 in ± 0.02 in 1 mmProvisionalWorked out: An assumption for the drawing, not a reading: the heads are flush with the face in the photo, and what is behind them doesn't show.
Worked out 0.04 in ± 0.02 in used
An assumption for the drawing, not a reading: the heads are flush with the face in the photo, and what is behind them doesn't show., harvested
Clearance round the wheel in its pocket in the left wall0.02 in ± 0.01 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the side photo shows the pocket's rim round the wheel's teeth as a dark ring a few pixels wide, which no scale on file resolves.
Worked out 0.02 in ± 0.01 in used
An assumption for the drawing, not a reading: the side photo shows the pocket's rim round the wheel's teeth as a dark ring a few pixels wide, which no scale on file resolves., harvested
How far the wheel's face is dished inside its rim0.01 in ± 0.01 in 0.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: the side photo shows the face's rim as a bright ring, its depth not.
Worked out 0.01 in ± 0.01 in used
An assumption for the drawing, not a reading: the side photo shows the face's rim as a bright ring, its depth not., harvested
The socket in the wheel's middle, its depth0.08 in ± 0.04 in 2 mmProvisionalWorked out: An assumption for the drawing, not a reading: the socket shows dark in the side photo, its depth not.
Worked out 0.08 in ± 0.04 in used
An assumption for the drawing, not a reading: the socket shows dark in the side photo, its depth not., harvested
The set screw's hole in the rear end, its depth0.1 in ± 0.05 in 2.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the drawing has the hole end on.
Worked out 0.1 in ± 0.05 in used
An assumption for the drawing, not a reading: the drawing has the hole end on., harvested
How far the set screw's end stands back in its hole0.02 in ± 0.02 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the photos show the screw's end just inside the hole's rim.
Worked out 0.02 in ± 0.02 in used
An assumption for the drawing, not a reading: the photos show the screw's end just inside the hole's rim., harvested
The aluminium's edges, broken0.008 in ± 0.005 in 0.2 mmProvisionalWorked out: An assumption for the drawing, not a reading: the photos show every edge of the body softened, by an amount no view on file resolves.
Worked out 0.008 in ± 0.005 in used
An assumption for the drawing, not a reading: the photos show every edge of the body softened, by an amount no view on file resolves., harvested
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Picatinny rail (MIL-STD-1913)
- Uppers
- Aero Precision M4E1 Enhanced Upper Receiver Stripped, Aero Precision M4E1 Threaded upper receiver, BCM M4 Upper Receiver Assembly (w/ Laser T-Markings), Expo Arms 7075 Stripped AR-15 Upper Receiver, Geissele Automatics Super Duty Stripped Upper Receiver, Nordic Components 22RB .22 LR upper, 16", Palmetto State Armory AR-15 Stripped Upper Receiver, Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12", Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16"
- Handguards
- Aero Precision AR15 10.3" R-ONE M-LOK handguard, Aero Precision AR15 12.7" R-ONE M-LOK handguard, Aero Precision AR15 15" Enhanced M-LOK Handguard, Gen 2, Aero Precision AR15 15" R-ONE M-LOK handguard, Aero Precision AR15 15" S-ONE M-LOK Handguard, Aero Precision AR15 16.6" R-ONE M-LOK handguard, Aero Precision AR15 7.3" R-ONE M-LOK handguard, Aero Precision AR15 9.3" R-ONE M-LOK handguard, BCM MCMR-10 (M-LOK® Compatible* Modular Rail), BCM MCMR-13 (M-LOK® Compatible* Modular Rail), BCM MCMR-15 (M-LOK® Compatible* Modular Rail), Expo Arms Free Float AR-15 Handguard - M-LOK - 15", Geissele Automatics 10.5" Super Modular Rail MK16 M-LOK, Geissele Automatics 13.5" Super Modular Rail MK16 M-LOK, Geissele Automatics 15" Super Modular Rail MK16 M-LOK, MAS Defense 12.62" NERO M-LOK FREE FLOAT, MAS Defense 15" NERO M-LOK FREE FLOAT, MAS Defense 9.87" NERO M-LOK FREE FLOAT, Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length), Midwest Industries Combat Rail One Piece Free Float Handguard, M-LOK™ (15")
- Frames
- Taurus TX22 Gen 2 frame
- Rail sections
- Magpul M-LOK® Aluminum Rail, 3 Slots, Magpul M-LOK® Aluminum Rail, 5 Slots, Magpul M-LOK® Aluminum Rail, 7 Slots, Magpul M-LOK® Aluminum Rail, 9 Slots, Magpul M-LOK® Polymer Rail, 11 Slots, Magpul M-LOK® Polymer Rail, 3 Slots, Magpul M-LOK® Polymer Rail, 5 Slots, Magpul M-LOK® Polymer Rail, 7 Slots, Magpul M-LOK® Polymer Rail, 9 Slots
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Scalarworks $159.00 Black Nov 21, 2026, in stock that day
- MidwayUSA $159.00 Black Nov 21, 2026, in stock that day
- T.REX ARMS $159.00 Black Nov 21, 2026, out of stock that day