Optic
SIG Sauer ROMEO-MSR GEN II red dot sight, 2 MOA red dot
SIG Sauer's ROMEO-MSR GEN II, a 1x20 mm red dot with a 2 MOA dot and a rotary brightness dial that holds its CR2032, screwed to its mount by the Micro footprint (Vyce Outdoor: "The Sig Sauer MSR Gen 2 uses the Aimpoint "Micro" footprint"). Its axis is 0.60 in over its own base: on the see-through riser it is sold on that is "SIGHT HEIGHT 1.41" ABSOLUTE CO-WITNESS" (SIG's sheet). In the box: "CR2032 Battery, T10 Multi-Tool & Rubber Lens Cover". The page linked is Primary Arms': SIG's own site isn't read.

- Weight
- 3.9 oz ± 0.4 oz Provisionalworked out: {.weight} - {sig-romeo-msr-riser-mount.weight}
- Lowest price
- Sold in the SIG Sauer ROMEO-MSR GEN II red dot sight, 2 MOA red dot, on its see-through riser, not by itself
- Colours
- Black, Flat Dark Earth
- Drawn as
- modelled
- Maker's page
- primaryarms.com
In “Budget 16 in carbine”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Overall length2.744 in 69.7 mmConfirmedPublished: SIG Sauer, ROMEO-MSR GEN II 1x20 mm spec sheet (REV. 2.7.2024), the PDF as OpticsPlanet hosts it, the maker, read Oct 5, 2026
Published “OVERALL LENGTH 2.7 in 69.7 mm” used
SIG Sauer, ROMEO-MSR GEN II 1x20 mm spec sheet (REV. 2.7.2024), the PDF as OpticsPlanet hosts it, the maker, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “Length : 2.70"”
Impact Guns, SIG ROMEO-MSR Gen 2 red dot 1x20mm black (798681694624, SORMSR101), specifications, a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
The sheet's 2.7 in with a zero written after it: no closer than the sheet's own inches.
SIG's own sheet, in the unit it gives to three figures; the seller's inches round it.
Overall width (the raised panel's face on the left flank to the brightness dial's face, on the right)1.764 in 44.8 mmConfirmedPublished: SIG Sauer, ROMEO-MSR GEN II 1x20 mm spec sheet (REV. 2.7.2024), the PDF as OpticsPlanet hosts it, the maker, read Oct 5, 2026
Published “OVERALL WIDTH 1.8 in 44.8 mm” used
SIG Sauer, ROMEO-MSR GEN II 1x20 mm spec sheet (REV. 2.7.2024), the PDF as OpticsPlanet hosts it, the maker, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “Width : 1.8"”
Impact Guns, SIG ROMEO-MSR Gen 2 red dot 1x20mm black (798681694624, SORMSR101), specifications, a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
SIG's own sheet, in the unit it gives to three figures; the seller's inches round it.
The sheet doesn't say what it spans: it is taken across the two things that stand furthest out, the raised panel on the left flank and the dial on the right. The photo from behind gives how the width divides between them (left_panel_reach_z: 0.68 in left of the axis, so the dial's face 1.08 in right of it). Until 2026-10-05 the left side was taken as the round tube's (0.584 in) and the dial's face stood 1.18 in out.
Overall height (the clamp's bottom to the elevation turret's top, on its riser)2.476 in 62.9 mmConfirmedPublished: SIG Sauer, ROMEO-MSR GEN II 1x20 mm spec sheet (REV. 2.7.2024), the PDF as OpticsPlanet hosts it, the maker, read Oct 5, 2026
Published “OVERALL HEIGHT 2.5 in 62.9 mm” used
SIG Sauer, ROMEO-MSR GEN II 1x20 mm spec sheet (REV. 2.7.2024), the PDF as OpticsPlanet hosts it, the maker, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “Height : 2.50"”
Impact Guns, SIG ROMEO-MSR Gen 2 red dot 1x20mm black (798681694624, SORMSR101), specifications, a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
The sheet's 2.5 in with a zero written after it: no closer than the sheet's own inches.
SIG's own sheet, in the unit it gives to three figures; the seller's inches round it.
From the bottom of the riser's rail clamp, not the rail's top: two straight side views scaled by the sheet's length read 2.48 and 2.49 in between those two (the sheet: 62.9 mm, 2.476 in).
Optical axis above the rail's top (on the riser it comes on)1.41 in 35.8 mmConfirmedPublished: SIG Sauer, ROMEO-MSR GEN II 1x20 mm spec sheet (REV. 2.7.2024), the PDF as OpticsPlanet hosts it, the maker, read Oct 5, 2026
Published “SIGHT HEIGHT 1.41" ABSOLUTE CO-WITNESS” used
SIG Sauer, ROMEO-MSR GEN II 1x20 mm spec sheet (REV. 2.7.2024), the PDF as OpticsPlanet hosts it, the maker, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “Mount Height : 1.41"”
Impact Guns, SIG ROMEO-MSR Gen 2 red dot 1x20mm black (798681694624, SORMSR101), specifications, a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
SIG's own sheet; the seller repeats it.
SIG's "sight height", with "absolute co-witness" beside it: taken as the rail's top to the optical axis, as a sight height is given. The side view agrees with it only through the clamp's depth, which nothing else gives (clamp_below_rail).
Weight without its battery (the sheet's figure; it doesn't say whether the riser is in it)5.7 ozConfirmedPublished: SIG Sauer, ROMEO-MSR GEN II 1x20 mm spec sheet (REV. 2.7.2024), the PDF as OpticsPlanet hosts it, the maker, read Oct 5, 2026
Published “WEIGHT W/O BATTERY 5.7 oz 161 g” used
SIG Sauer, ROMEO-MSR GEN II 1x20 mm spec sheet (REV. 2.7.2024), the PDF as OpticsPlanet hosts it, the maker, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “Weight 5.7 oz”
Primary Arms, SIG Sauer ROMEO-MSR GEN II 2 MOA red dot sight (SORMSR101), specifications, a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “Weight : 5.7 oz”
Impact Guns, SIG ROMEO-MSR Gen 2 red dot 1x20mm black (798681694624, SORMSR101), specifications, a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
SIG's own sheet, which says what it leaves out; two sellers repeat the figure.
"W/O BATTERY" is the sheet's; a CR2032's own weight is on no page on file and isn't added. The sight is sold only on its riser, and the sheet names no weight without one.
Objective lens diameter0.787 in 20 mmConfirmedPublished: SIG Sauer, ROMEO-MSR GEN II 1x20 mm spec sheet (REV. 2.7.2024), the PDF as OpticsPlanet hosts it, the maker, read Oct 5, 2026
Published “OBJECTIVE LENS 20 mm” used
SIG Sauer, ROMEO-MSR GEN II 1x20 mm spec sheet (REV. 2.7.2024), the PDF as OpticsPlanet hosts it, the maker, read Oct 5, 2026 the page, harvested Oct 5, 2026
Draws the lens at the front; the rear window's own size isn't published and is drawn the same.
Optical axis above the riser clamp's bottom1.655 in ± 0.012 in 42 mmProvisionalPhoto: Primary Arms SORMSR101_02, the sight on its riser, straight left side on white, 2200 x 1467, objective to the left
Photo 1.655 in ± 0.012 in used
Primary Arms SORMSR101_02, the sight on its riser, straight left side on white, 2200 x 1467, objective to the left, harvested
Scale: the sheet's length, 69.7 mm = 1403 px (511.3 px/in), and its height, 62.9 mm = 1274 px (514.5 px/in), which agree within 0.6%: 512.9 px/in. Read by the objective bezel's ring is round about the axis: the middle of the dark run through it at five columns 0.10 to 0.30 in behind its front reads 1.655 to 1.656 in above the silhouette's lowest row, the clamp's bottom
The ± is the two scales' 0.6% over this height and a pixel at each end.
Riser clamp's bottom below the rail's top0.245 in ± 0.012 in 6.2 mmProvisionalWorked out: {.axis_above_clamp_bottom} - {.optical_axis_above_rail}
Worked out 0.245 in ± 0.012 in used
{.axis_above_clamp_bottom} - {.optical_axis_above_rail}, harvested
The jaws wrap the rail's sides: the HM3X's reach 0.22 in and the ARO's 0.23. The photo from behind reads 0.234 in on its own scale.
Riser clamp's bottom in the optic frame (y, the rail's top is 0)-0.245 in ± 0.012 in -6.2 mmProvisionalWorked out: -{.clamp_below_rail}
Worked out -0.245 in ± 0.012 in used
-{.clamp_below_rail}, harvested
Where the side profile's clamp-bottom origin sits in the part frame.
Main tube OD (twice its underside's distance below the axis)1.168 in ± 0.02 in 29.7 mmProvisionalPhoto: Primary Arms SORMSR101_02, the sight on its riser, straight left side on white, 2200 x 1467, objective to the left
Photo 1.168 in ± 0.02 in used
Primary Arms SORMSR101_02, the sight on its riser, straight left side on white, 2200 x 1467, objective to the left, harvested
Scale: the sheet's length, 69.7 mm = 1403 px (511.3 px/in), and its height, 62.9 mm = 1274 px (514.5 px/in), which agree within 0.6%: 512.9 px/in. Read by the silhouette's underside ahead of the riser (0.4 to 0.5 in behind the front: 1.072 and 1.070 in above the clamp's bottom) and behind it (2.5 in: 1.072) lies 0.583 to 0.585 in below the bezel's centre: twice 0.584
A dark tube's edge on white reads a little thin: the ± allows 1.5%.
Its top is under the housing and its sides aren't seen square on: the tube is taken as round about the axis, as the bezel ahead of it is and as the photo from behind shows its rear rim.
The tube's underside where it overhangs the riser, above the riser clamp's bottom1.071 in ± 0.012 in 27.2 mmProvisionalPhoto: Primary Arms SORMSR101_02, the sight on its riser, straight left side on white, 2200 x 1467, objective to the left
Photo 1.071 in ± 0.012 in used
Primary Arms SORMSR101_02, the sight on its riser, straight left side on white, 2200 x 1467, objective to the left, harvested
Scale: the sheet's length, 69.7 mm = 1403 px (511.3 px/in), and its height, 62.9 mm = 1274 px (514.5 px/in), which agree within 0.6%: 512.9 px/in. Read by the silhouette's underside just ahead of the riser's front and just behind its rear, where the body overhangs it: 1.070 to 1.072 in above the clamp's bottom
Called the riser's top until 2026-11-05, when the riser became a part of its own: the riser's top is the seam with the housing's flat base, 0.013 in lower (base_above_clamp_bottom).
The sight's own base (its seam with the riser's top) above the riser clamp's bottom1.058 in ± 0.008 in 26.9 mmProvisionalPhoto: Primary Arms SORMSR101_02, the sight on its riser, straight left side on white, 2200 x 1467, objective to the left
Photo 1.058 in ± 0.008 in used
Primary Arms SORMSR101_02, the sight on its riser, straight left side on white, 2200 x 1467, objective to the left, harvested
Scale: the sheet's length, 69.7 mm = 1403 px (511.3 px/in), and its height, 62.9 mm = 1274 px (514.5 px/in), which agree within 0.6%: 512.9 px/in. Read by the darkest row of the seam line between the housing's base and the riser, in ten bands of 60 columns from column 700 to 1660: rows 828 (front) to 825 (rear), the silhouette's lowest row (the clamp's bottom) 1369: 1.055 to 1.061 in at 512.9 px/in
Where the housing's flat base comes down onto the riser, and so the plane the sight's footprint meets a mount's deck in: the housing's flank runs down past the round tube to a flat base the riser's length, with ROMEO-MSR printed on it, and a dark line parts it from the riser along its whole length. SIG's rendering of the flat dark earth sight (c4fea0598ed4) has that base in the housing's tan, down to the riser's black top. The line falls 0.006 in from the rear end to the front over 900 px, less than its own width: the photo's roll or the part's, and read as level.
Optical axis above the sight's own base (the plane its footprint meets a mount's deck in: D101)0.597 in ± 0.014 in 15.2 mmProvisionalWorked out: {.axis_above_clamp_bottom} - {.base_above_clamp_bottom}
Worked out 0.597 in ± 0.014 in used
{.axis_above_clamp_bottom} - {.base_above_clamp_bottom}, harvested
1.655 in less 1.058, both on Primary Arms' side view at one scale.
What the sight brings to any Micro-footprint mount: its axis this far over the deck it is screwed to. On its own riser it puts the axis at SIG's 1.41 in, which is what the riser's deck height is worked out from (sig-romeo-msr-riser-mount.deck_above_rail). The photo from behind (ff6f13b2efd1) reads the riser's top 0.584 in under the axis through its camera; it was taken there to be the tube's underside, the same 0.584, and isn't a reading of the seam.
Riser's length along the rail (its clamp's)1.973 in ± 0.015 in 50.1 mmProvisionalPhoto: Primary Arms SORMSR101_02, the sight on its riser, straight left side on white, 2200 x 1467, objective to the left
Photo 1.973 in ± 0.015 in used
Primary Arms SORMSR101_02, the sight on its riser, straight left side on white, 2200 x 1467, objective to the left, harvested
Scale: the sheet's length, 69.7 mm = 1403 px (511.3 px/in), and its height, 62.9 mm = 1274 px (514.5 px/in), which agree within 0.6%: 512.9 px/in. Read by the silhouette's row widths over the riser, 0.60 to 0.97 of the height down from the top: 1001 to 1014 px, median 1012
Five rail slots' worth (1.97 in at std.picatinny.slot_pitch).
Riser's width across its two legs1.113 in ± 0.04 in 28.3 mmProvisionalPhoto: GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701
Photo 1.113 in ± 0.04 in used
GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701, harvested
Scale: a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives). Read by the legs' outer edges at the riser's rear face (0.244 in ahead of the body's rear face by the side view), columns 1220 and 1740: 520 px at 467.1 px/in
A rail's 0.835 in between two jaws of about 0.14 in each. The ± is 10 px of reading and the camera's fit.
Riser's width at its top, under the body (above its shoulders)0.856 in ± 0.04 in 21.7 mmProvisionalPhoto: GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701
Photo 0.856 in ± 0.04 in used
GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701, harvested
Scale: a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives). Read by the riser's top where the body sits on it, columns 1280 to 1680 at rows 1000 to 1020: 400 px at 467.1 px/in; its shoulders slope from there out to the legs' width by row 1095
How far below the riser's top its shoulders reach the legs' full width0.197 in ± 0.03 in 5 mmProvisionalPhoto: GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701
Photo 0.197 in ± 0.03 in used
GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701, harvested
Scale: a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives). Read by the shoulders' slopes end on the legs' outer faces at row 1095 on both sides, 92 px below the riser's top (row 1003) at 467.1 px/in
Width of the opening through the riser (the see-through)0.841 in ± 0.04 in 21.4 mmProvisionalPhoto: GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701
Photo 0.841 in ± 0.04 in used
GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701, harvested
Scale: a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives). Read by the opening's side walls at the riser's rear face, columns 1282 and 1675: 393 px at 467.1 px/in
The rail's own width (std.picatinny.top_width, 0.835): the legs stand on its two edges.
Top of the opening through the riser, above the rail's top0.558 in ± 0.04 in 14.2 mmProvisionalPhoto: GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701
Photo 0.558 in ± 0.04 in used
GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701, harvested
Scale: a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives). Read by the opening's upper edge, row 1128, 398 px below the axis (row 730) at 467.1 px/in: 0.852 in below the axis, which is optical_axis_above_rail above the rail's top
Floor of the opening through the riser (its base's top), above the rail's top0.119 in ± 0.04 in 3 mmProvisionalPhoto: GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701
Photo 0.119 in ± 0.04 in used
GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701, harvested
Scale: a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives). Read by the near edge of the base's top face, with its four slots, row 1333: 603 px below the axis at 467.1 px/in, 1.291 in below it
Width of the housing along the top (under the elevation turret)0.51 in ± 0.04 in 13 mmProvisionalPhoto: GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701
Photo 0.51 in ± 0.04 in used
GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701, harvested
Scale: a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives). Read by the housing's two flanks above the tube's rim, columns 1335 and 1560 (225 px) at rows 380 to 480, taken 0.5 to 0.6 in ahead of the rear face (444 to 436 px/in): 0.506 to 0.516 in
Where along the sight the flanks seen from behind lie is read off the side view's slope; the ± covers a quarter inch of it.
The raised panel on the left flank: how far left of the axis its face stands0.68 in ± 0.035 in 17.3 mmProvisionalPhoto: GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701
Photo 0.68 in ± 0.035 in used
GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701, harvested
Scale: the sheet's overall width (44.8 mm, 1.764 in) as what the panel's reach and the dial's add up to; the photo gives their ratio, each read at its own distance from the lens (the camera of this photo's other readings, 4.756 in behind the rear face). Read by the sight's left edge is straight over rows 700 to 840 at column 1174.5 (a round rim would run in 9 px over those rows), 304.5 px left of the axis (column 1479: the window's centre; the riser's legs are centred on 1477.5), and is 18 and 22 px further in at rows 640 and 880, where the panel's swell about the medallion shows, 0.33 in further off (a flat face along the sight would step 19 px): it is the panel's rear end, 0.22 in ahead of the rear face by the side view. The dial's edge on the same rows is column 1878.5, 399.5 px right of the axis, its rear rim 1.24 in ahead of the rear face (dial_from_front less half dial_od). The reaches are as 304.5 x 4.976 to 399.5 x 5.995, 1 to 1.581: 0.683 and 1.081 of the sheet's 1.764
The ± covers 0.7 in of the lens's distance, 0.1 in of where each edge is along the sight, 2 px on each, and the camera's own scale, by which the two read 0.649 and 1.025 in (1.674 in all, 5% under the sheet). It doesn't cover the sheet's width spanning something else.
The flat panel with SIG SAUER on it and the medallion at its rear (profiles.side has its outline as a feature). From behind it is the sight's left edge, not the tube's rim. The photo gives the ratio of its reach to the dial's; the sheet's overall width, taken across the two, gives the sizes: the dial's face is the width less this.
Brightness dial's diameter (the knurled ring, on the right)1.09 in ± 0.06 in 27.7 mmProvisionalPhoto: GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701
Photo 1.09 in ± 0.06 in used
GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701, harvested
Scale: a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives). Read by the dial seen edge on, its knurls' tips at rows 540 and 930 (390 px), 1.79 in ahead of the rear face (dial_from_front) at 356.8 px/in
The ± covers 0.2 in of where along the sight the dial stands and 8 px of reading. Its centre reads 0.014 in below the axis: on it. How far in toward the tube its ring begins isn't seen from behind (the windage boss stands before it).
Brightness dial's axis behind the sight's front face0.96 in ± 0.08 in 24.4 mmProvisionalPhoto: Impact Guns sig-sormsr101-2, the left side from a little above, on white, 2000 x 2000: the dial's rim shows over the body's top
Photo 0.96 in ± 0.08 in used
Impact Guns sig-sormsr101-2, the left side from a little above, on white, 2000 x 2000: the dial's rim shows over the body's top, harvested
Scale: the sheet's length, 69.7 mm = 1372 px (500.0 px/in); its height reads 528 px/in in this photo, which is taken from above, so only a length along the sight is read. Read by the dial's knurled rim shows above the body's top edge between columns 640 and 905, a chord of a circle about its axis: its middle, column 772, is 480 px behind the front face (column 292)
The dial is on the far side of the sight in this photo, 1.7 in further from the lens: from a studio distance that is 0.02 in toward the photo's middle, inside the ±.
Windage turret's boss: its diameter (on the right, behind the dial)0.64 in ± 0.08 in 16.3 mmProvisionalPhoto: GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701
Photo 0.64 in ± 0.08 in used
GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701, harvested
Scale: a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives). Read by the boss marked R, seen from behind as a block from row 612 to row 890 (278 px), taken 0.6 in ahead of the rear face (436 px/in)
Where along the sight it stands isn't read on any straight view: the quarter views show it behind the dial, level with the elevation turret, and it is taken there. The ± covers 0.3 in of that.
Windage turret's cap: how far right of the axis it reaches0.87 in ± 0.08 in 22.1 mmProvisionalPhoto: GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701
Photo 0.87 in ± 0.08 in used
GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701, harvested
Scale: a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives). Read by the boss's right edge, column 1860, 381 px right of the axis (column 1479), taken 0.6 in ahead of the rear face (436 px/in)
Read as 0.94 in until 2026-10-05, from column 1450 (the middle of a circle fitted to the rim and, on its left, to the raised panel: the camera's note has it).
Windage turret's centre below the optical axis0.05 in ± 0.04 in 1.3 mmProvisionalPhoto: GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701
Photo 0.05 in ± 0.04 in used
GAT Daily's review, a phone photo from behind the sight on a rifle's rail, looking forward through it, 3024 x 1701, harvested
Scale: a pinhole camera fitted to two sizes on the sight's own axis: the tube's rear rim, a circle of radius 273 px about (1450, 730), taken as tube_od (1.168 in) 0.24 in ahead of the rear face, and the objective lens seen through the tube, 250 px across, the sheet's 20 mm, 2.6 in ahead of it: the lens stood 4.76 in behind the rear face and a length t in ahead of that face reads 2335.6 / (4.756 + t) px/in. Checked on what it wasn't fitted to: the clamp's bottom reads 0.234 in below the rail's top (0.245 by the side view), the riser's top 0.584 in below the axis (0.584), the turret's top 0.847 in above it (0.829). Across the sight the axis is column 1479: the window's centre, with the riser's two legs centred on 1477.5 (the circle's 1450 is 29 px left of it: its left side was fitted to the raised panel on the left flank, which stands out past the rim; until 2026-10-05 the dial's face was read from 1450 as 1.177 in right of the axis and, with the tube's 0.584 in taken as the left side, seemed to make the sheet's width: left_panel_reach_z has what the photo gives). Read by the boss's middle between rows 612 and 890, row 751, 21 px below the axis at 436 px/in
Elevation turret's axis behind the sight's front face2.1 in ± 0.06 in 53.3 mmProvisionalPhoto: Primary Arms SORMSR101_02, the sight on its riser, straight left side on white, 2200 x 1467, objective to the left
Photo 2.1 in ± 0.06 in used
Primary Arms SORMSR101_02, the sight on its riser, straight left side on white, 2200 x 1467, objective to the left, harvested
Scale: the sheet's length, 69.7 mm = 1403 px (511.3 px/in), and its height, 62.9 mm = 1274 px (514.5 px/in), which agree within 0.6%: 512.9 px/in. Read by the silhouette's flat top, the turret's cap, runs from 2.0 to 2.2 in behind the front face at 2.484 in above the clamp's bottom: its middle
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Optic footprint
- Red dot mounts
- Aimpoint Duty RDS One-piece TNP Mount, 30 mm, Aimpoint LRP (Lever Release Picatinny) Mount with 39 mm Spacer, for Micro, Aimpoint One-piece Torsion Nut Mount and Spacer, 39 mm, Geissele Super Precision T1 Mount - 1.93" Height, Geissele Super Precision T1 Mount - Absolute Co-Witness, Geissele Super Precision T1 Mount - Lower 1/3 Co-Witness, Holosun 1.63 in lower 1/3 co-witness pedestal mount (HS-MOUNT-AR-RISER-ARO), Midwest Industries MK2 QD T2 Aimpoint Mount, Low, Midwest Industries MK2 QD T2 Aimpoint Mount, Lower 1/3 Cowitness, Midwest Industries MK2 QD T2 Aimpoint Mount, NV 2.26 in Height, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – 1.93″ HEIGHT, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – LOWER 1/3 (39MM HEIGHT), Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.42 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.57 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.93 in, Scalarworks LEAP/02 Aimpoint Micro T-2 quick-detach mount, 2.26 in, SIG Sauer M1913 I-BEAM Mount, 1.41 in absolute co-witness, SIG Sauer See-Through Riser Mount, 1.41 in absolute co-witness, Unity Tactical FAST Micro Mount, 2.26 in optical centerline