Magnifier
EOTECH G45 Magnifier, STS Mount
A 5X magnifier on EOTECH's Switch-to-Side (STS) quick-detach mount, with its 7 mm riser fitted, as EOTECH pictures it (lower third co-witness), or without it (absolute co-witness): the lever on the rifle's left, the hinge on its right. In line behind the sight, or swung aside to the right.

- Weight
- 12.8 oz Conflictpublished: eotechinc.com, G45 Magnifier (Tech Specs), the maker, read Oct 12, 2026Its sources span 12.8 oz to 13 oz.
- Lowest price
- $604.04 at KYGUNCO, read Nov 21, 2026 (Tan)
- Maker's number
- G45.STS
- Colours
- Black, Tan
- Drawn as
- modelled
- Maker's page
- eotechinc.com
In “Aero M4E1 Enhanced, pencil barrel”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Overall length (the objective's front face to the diopter ring's rear face)3.751 in ± 0.04 in 95.3 mmConflictPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Published “L × W × H 3.9" x 2.3" x 3.3" (99 x 58.4 x 83.8 mm)”
eotechinc.com, G45 Magnifier (Tech Specs), the maker, read Oct 12, 2026 the page, harvested Oct 12, 2026
Published “L × W × H 3.9” × 2.3” × 3.3” / 99 × 58.4 × 83.8mm”
EOTECH full catalogue (PDF), p. 22, the maker, read Oct 12, 2026 the page, harvested Oct 12, 2026
Published “L×W×H 3.9" × 2.3" × 3.3" (99 × 58.4 × 83.8mm)”
EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 7, the maker, read Oct 12, 2026 the page, harvested Oct 12, 2026
Published “L X W X H 3.9" x 2.3" x 3.3" (99 x 58.4 x 83.8 mm)”
T.REX ARMS, EOTECH G45 5x Magnifier, a seller, read Oct 12, 2026 the page, harvested Oct 12, 2026
Published “Length: 3.9””
Primary Arms, EOTECH G45 5X Magnifier - Black (G45.STS), a seller, read Oct 12, 2026 the page, harvested Oct 12, 2026
Published “Length: 3.9 In”
Silencer Shop, EOTECH G45 5X Magnifier (EO-G45.STS), a seller, read Oct 12, 2026 the page, harvested Oct 12, 2026
Published “Compact length of approximately 116.3 mm (4.58 in).”
Optics Trade, EOTech Magnifier G45, a seller, read Oct 12, 2026 the page, harvested Oct 12, 2026
The shop's own prose; its table on the same page says "Length. 3.90 inch (99.00 mm)".
Photo 3.751 in ± 0.04 in used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by the objective's front edge at column 219 (rows 678 to 834) and the diopter ring's rear edge at 1864: 1645 px. The ± is 1%: three side views scaled each by its own picture of the mount's top plate read 3.75, 3.76 and 3.83
What the maker's own side view reads at a scale two of its published sizes agree on, and what the model is held to. The published 3.9 in is 4% more than any of three side views has between the magnifier's two end faces, and no page says what it spans.
page and optics-trade-prose differ by 0.681 in beyond what each states it is good to.
page and left differ by 0.147 in beyond what each states it is good to.
catalog and optics-trade-prose differ by 0.681 in beyond what each states it is good to.
catalog and left differ by 0.147 in beyond what each states it is good to.
manual-2022 and optics-trade-prose differ by 0.681 in beyond what each states it is good to.
manual-2022 and left differ by 0.147 in beyond what each states it is good to.
trex and optics-trade-prose differ by 0.681 in beyond what each states it is good to.
trex and left differ by 0.147 in beyond what each states it is good to.
pa and optics-trade-prose differ by 0.679 in beyond what each states it is good to.
pa and left differ by 0.149 in beyond what each states it is good to.
silencer and optics-trade-prose differ by 0.679 in beyond what each states it is good to.
silencer and left differ by 0.149 in beyond what each states it is good to.
optics-trade-prose and left differ by 0.828 in beyond what each states it is good to.
EOTECH publishes 3.9 in everywhere and says nowhere what it spans. Its own left side view, at the scale where the mount's published 1.66 in and the kit's published 3.3 in height agree within 0.2%, has 1645 px from the objective's front to the diopter ring's rear: 3.75 in; the whole picture, the mount's top plate standing 5 px ahead of the objective, is 1650 px (3.76). Rifle Supply's right side view reads 3.76 at its own plate's scale and Primary Arms' left side view 3.83. At 3.9 in the picture would be 62 px longer than it is. The diopter ring turns to focus and may stand further out than pictured; a seller's 116.3 mm fits nothing in any picture.
Overall width2.299 in 58.4 mmConfirmedPublished: eotechinc.com, G45 Magnifier (Tech Specs), the maker, read Oct 12, 2026
Published “L × W × H 3.9" x 2.3" x 3.3" (99 x 58.4 x 83.8 mm)” used
eotechinc.com, G45 Magnifier (Tech Specs), the maker, read Oct 12, 2026 the page, harvested Oct 12, 2026
Published “L×W×H 3.9" × 2.3" × 3.3" (99 × 58.4 × 83.8mm)”
EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 7, the maker, read Oct 12, 2026 the page, harvested Oct 12, 2026
Published “Width: 2.3 In”
Silencer Shop, EOTECH G45 5X Magnifier (EO-G45.STS), a seller, read Oct 12, 2026 the page, harvested Oct 12, 2026
The maker's figure, which its manual and a seller repeat.
No view square across the magnifier is on file: the published figure can't be held against a picture. The model is 2.12 in across: the lever's face 1.0 in left of the rail's middle (the same mount's, the G33's ledger) and the horizontal knob's 1.12 in right of it (side_knob_reach, worked out from the side view): see the part's approximations.
Overall height, the riser fitted (the vertical adjustment's knob to the clamp's bottom)3.299 in 83.8 mmConfirmedPublished: eotechinc.com, G45 Magnifier (Tech Specs), the maker, read Oct 12, 2026
Published “L × W × H 3.9" x 2.3" x 3.3" (99 x 58.4 x 83.8 mm)” used
eotechinc.com, G45 Magnifier (Tech Specs), the maker, read Oct 12, 2026 the page, harvested Oct 12, 2026
Published “L × W × H 3.9” × 2.3” × 3.3” / 99 × 58.4 × 83.8mm”
EOTECH full catalogue (PDF), p. 22, the maker, read Oct 12, 2026 the page, harvested Oct 12, 2026
Published “L×W×H 3.9" × 2.3" × 3.3" (99 × 58.4 × 83.8mm)”
EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 7, the maker, read Oct 12, 2026 the page, harvested Oct 12, 2026
Photo 3.304 in ± 0.02 in
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate alone (728 px: 438.2 px/in). Read by the silhouette's top row to its bottom row, 282 to 1729: 1448 px, the vertical adjustment knob's top to the clamp's bottom
The maker's figure, in its page, catalogue and manual; its own side view reads 0.005 in more at the scale the mount's published length gives, inside its ±.
The published figure doesn't say whether the riser is fitted; EOTECH's own picture, which has it, reads the figure within 0.2% at the scale the mount's own published length gives: with the riser.
Weight of the magnifier alone9.5 ozConfirmedPublished: eotechinc.com, G45 Magnifier (Tech Specs), the maker, read Oct 12, 2026
Published “Weight without STS ™ Mounting System 9.5 oz (269.3 g)” used
eotechinc.com, G45 Magnifier (Tech Specs), the maker, read Oct 12, 2026 the page, harvested Oct 12, 2026
Weight of the STS mount as the kit has it (the mount, the riser and its screws)3.3 oz ± 0.0035 ozProvisionalWorked out: {.weight} - {.weight_without_mount}
Worked out 93.6 g ± 0.1 g used
{.weight} - {.weight_without_mount}, harvested
The difference of EOTECH's two figures for the G45. Its 2015 sheet has the mount alone at 81 g, and a reviewer's scale 87 g (the G33's ledger, sts_mount_weight).
Eye relief2.598 in 66 mmConfirmedPublished: eotechinc.com, G45 Magnifier (Tech Specs), the maker, read Oct 12, 2026
Published “Eye Relief 2.6" (66 mm)” used
eotechinc.com, G45 Magnifier (Tech Specs), the maker, read Oct 12, 2026 the page, harvested Oct 12, 2026
Published “Eye Relief 2.6" (66mm)”
EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 7, the maker, read Oct 12, 2026 the page, harvested Oct 12, 2026
Published “2.6” / 66mm”
EOTECH full catalogue (PDF), p. 22, the maker, read Oct 12, 2026 the page, harvested Oct 12, 2026
Published “Eye Relief 2.6" (66mm)”
T.REX ARMS, EOTECH G45 5x Magnifier, a seller, read Oct 12, 2026 the page, harvested Oct 12, 2026
The maker's page; its manual, its catalogue and a seller say the same.
Field of view4.4°ConfirmedPublished: EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 7, the maker, read Oct 12, 2026
Published “Field-of-View 4.4°” used
EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 7, the maker, read Oct 12, 2026 the page, harvested Oct 12, 2026
Published “4.4˚”
EOTECH full catalogue (PDF), p. 22, the maker, read Oct 12, 2026 the page, harvested Oct 12, 2026
Published “Field-Of-View 4°”
eotechinc.com, G45 Magnifier (Tech Specs), the maker, read Oct 12, 2026 the page, harvested Oct 12, 2026
The manual's and the catalogue's figure; the page's 4° is the same figure without its tenth.
EOTECH's page rounds it to a whole degree, and its Exit Pupil row repeats that ("Exit Pupil 4°"): a slip, and no exit pupil is stated for the G45.
Exit pupilNo value yetMissingNo source yet
Not stated for the G45: EOTECH's page has the row, and in it the field of view again ("Exit Pupil 4°"). The G33's page states its own (7.6 mm). With one seller's "Objective 25" and the 5X it would be 5 mm; nothing is drawn from it.
Optical axis above the rail's top, with the 7 mm riser1.826 in ± 0.05 in 46.4 mmProvisionalWorked out: {.axis_above_clamp_bottom} - {.clamp_below_rail}
Worked out 1.826 in ± 0.05 in used
{.axis_above_clamp_bottom} - {.clamp_below_rail}, harvested
No page states a height: EOTECH's manual says the mount puts the magnifier "at either an absolute co-witness or lower-third co-witness height". It is the diopter ring's middle over the clamp's bottom on EOTECH's left side view of the G45 (2.196 in), less how far the same mount's clamp reaches under the rail's top (the G33's ledger: 0.37 in, which puts the G33's axis at a reviewer's 47 mm). T.REX ARMS' staff, of what it lines up with: "the G45 on a spacer with a lined up with a 193 Aimpoint T2 looks perfect".
Optical axis above the rail's top, without the riser1.55 in ± 0.04 in 39.4 mmProvisionalWorked out: {.optical_axis_above_rail_spacer} - {.riser_thickness}
Worked out 1.55 in ± 0.04 in used
{.optical_axis_above_rail_spacer} - {.riser_thickness}, harvested
Photo 1.614 in ± 0.05 in
Primary Arms' G45.STS_02: the left side, square on, in line, no riser, 2200 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (656 px: 394.8 px/in). Read by the diopter ring's middle (rows 249 to 842) over the top plate's underside (row 987): 441.5 px, 1.118 in; plus eotech-g45.plate_bottom_above_clamp_bottom, less eotech-g45.clamp_below_rail
The maker's own figure for the riser. The picture's reading is kept beside it: 0.06 in more, about what two side views' heights differ by.
Not drawn: the model has the riser fitted. Two routes: the maker's 7 mm taken off the height with the riser, and Primary Arms' left side view of a G45 without it, where the diopter ring's middle is 1.118 in over the mount's top plate's underside (441.5 px at its own plate's scale) against 1.346 in on EOTECH's view with the riser: 0.23 in between the two pictures for a riser of 0.276. The side views' heights differ by 2% from one to the next, which on a height of 2.2 in is as much as that.
The riser's thickness0.276 in 7 mmConfirmedPublished: EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 7, the maker, read Oct 12, 2026
Published “The 7mm riser (included) may be required to align the magnifier optical axis with the sight.” used
EOTECH G-Series Magnifiers user manual, January 2022 (hosted by T.REX ARMS), p. 7, the maker, read Oct 12, 2026 the page, harvested Oct 12, 2026
Optical axis above the clamp's bottom, the riser fitted2.196 in ± 0.03 in 55.8 mmConflictPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 2.196 in ± 0.03 in used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by the diopter ring's top and bottom rows 435 and 1097 over columns 1762 to 1846, their middle 766.5; the silhouette's bottom edge 1729.5: 963 px. Rifle Supply's right side view reads 2.16 at its plate's scale (its heights all read 2% under this view's)
Photo 2.268 in ± 0.04 in
eotechinc.com's gallery, EOTECH-G45-Tan-1: the tan kit's left side, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (682 px: 410.5 px/in), which the diopter ring and the armour's height bear out against the black kit's picture (0.936 of it, each). Its whole height reads 3.36 in at that scale, 1.8% over the published one: a view from a little below. Read by the diopter ring's top and bottom rows 556 and 1176, their middle 866.5; the silhouette's bottom edge 1797.5: 931 px
The black kit's picture is the level one: its whole height reads the published 3.3 in at the scale the mount's length gives, and its two scales agree within 0.2%. The tan kit's has the magnifier 0.07 in higher over the same top plate and the kit 0.06 in taller than published: seen from a little below, where the outline's bottom is the far jaw's and the armour's parting line, 0.04 in under the ring's middle on the black picture, lies on it.
left and tan differ by 0.072 in beyond what each states it is good to.
The axis is taken at the diopter ring's middle. The armoured body isn't centred on it: its top is 0.872 in above it and its underside 0.820 below, on all three side views (0.865 and 0.823 on Primary Arms', 0.867 and 0.812 on Rifle Supply's).
The eyepiece's rear face behind the mount's centre2.933 in ± 0.03 in 74.5 mmProvisionalPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 2.933 in ± 0.03 in used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by the diopter ring's rear edge at column 1864, the top plate's middle at 578 (its ends 214 and 942 over rows 1266 to 1338): 1286 px
Where the eye looks in: the eye relief runs back from here. The mount's centre is the middle of its top plate. The diopter ring turns, and stands where EOTECH pictured it.
The objective's front face ahead of the mount's centre0.819 in ± 0.015 in 20.8 mmProvisionalPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 0.819 in ± 0.015 in used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by the objective's front edge at column 219, the top plate's middle at 578: 359 px. The plate's own front end (214) stands 5 px ahead of it
The objective tube's outside diameter1.512 in ± 0.02 in 38.4 mmProvisionalPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 1.512 in ± 0.02 in used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by the tube's top edge at row 435 (columns 238 to 610), the axis at 766.5: 331.5 px, doubled
Its top edge above the axis, doubled: its underside is behind its foot in a side view. It comes to the diopter ring's diameter within a pixel, the two being about one axis.
The diopter ring's outside diameter1.512 in ± 0.012 in 38.4 mmProvisionalPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 1.512 in ± 0.012 in used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by rows 435 to 1097 over columns 1762 to 1846: 663 px
The neck between the armoured body and the diopter ring: its diameter1.295 in ± 0.012 in 32.9 mmProvisionalPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 1.295 in ± 0.012 in used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by rows 483 to 1050 at columns 1714 to 1726: 568 px
The armoured body's top above the optical axis0.872 in ± 0.01 in 22.1 mmProvisionalPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 0.872 in ± 0.01 in used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by the body's top edge at row 384 behind the knob (columns 1462 to 1654) and on the collar's top pad (658 to 1042), the axis at 766.5: 382.5 px
The armoured body's underside below the optical axis0.82 in ± 0.01 in 20.8 mmProvisionalPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 0.82 in ± 0.01 in used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by the body's bottom edge at row 1126 (columns 1162 to 1654), the axis at 766.5: 359.5 px
The armoured body's side flat: its upper edge above the optical axis0.334 in ± 0.015 in 8.5 mmConflictPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 0.334 in ± 0.015 in used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by down columns 1380 to 1440 and 1520 to 1580, the picture's brightness: the lit upper facet (150 of 255) falls to the dark side flat (45) between rows 608 and 632, its middle at 620; the axis at 766.5: 146.5 px
Photo 0.396 in ± 0.02 in
eotechinc.com's gallery, EOTECH-G45-Tan-1: the tan kit's left side, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (682 px: 410.5 px/in), which the diopter ring and the armour's height bear out against the black kit's picture (0.936 of it, each). Its whole height reads 3.36 in at that scale, 1.8% over the published one: a view from a little below. Read by down columns 1380 to 1440 and 1500 to 1560: the lit upper facet falls to the darker side flat between rows 700 and 708, its middle at 704; the diopter ring's middle at 866.5: 162.5 px
The black kit's picture is the level one (axis_above_clamp_bottom says why). The tan kit's has the same flat, 0.72 in tall, 0.055 in higher on the body: what faces the lens reads high in a view from below. Between the two the flat is about the axis; the model has the black picture's.
left and tan differ by 0.062 in beyond what each states it is good to.
The body behind the collar is eight-sided: a flat on top (the knob stands on it), one underneath, one down each side, and a facet between each two. In the side view the upper facet is lit and the side flat dark; the edge between them is a soft one.
The armoured body's side flat: its lower edge below the optical axis0.373 in ± 0.015 in 9.5 mmConflictPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 0.373 in ± 0.015 in used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by down the same columns: the dark side flat (47) gives way to the lower facet (75) between rows 924 and 936, its middle at 930; the axis at 766.5: 163.5 px
Photo 0.325 in ± 0.02 in
eotechinc.com's gallery, EOTECH-G45-Tan-1: the tan kit's left side, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (682 px: 410.5 px/in), which the diopter ring and the armour's height bear out against the black kit's picture (0.936 of it, each). Its whole height reads 3.36 in at that scale, 1.8% over the published one: a view from a little below. Read by down the same columns: the side flat gives way to the lower facet between rows 996 and 1004, its middle at 1000; the diopter ring's middle at 866.5: 133.5 px
As its upper edge: the black kit's picture, the level one; the tan kit's has the edge 0.05 in higher.
left and tan differ by 0.048 in beyond what each states it is good to.
The armoured body's half width (its side flat out from the optical axis's vertical)0.891 in ± 0.05 in 22.6 mmProvisionalWorked out: ({.body_side_flat_top_above_axis} + {.body_side_flat_bottom_below_axis}) / 2 + {.body_top_above_axis} - {.body_side_flat_top_above_axis}
Worked out 0.8915 in ± 0.05 in used
({.body_side_flat_top_above_axis} + {.body_side_flat_bottom_below_axis}) / 2 + {.body_top_above_axis} - {.body_side_flat_top_above_axis}, harvested
Worked out, not read: no view square across the magnifier is on file. The facets between the flats are taken at 45 degrees, so the body is as far out past its top flat's edge as the upper facet is tall in the side view (0.538 in); and the top flat is taken as wide as the side flats are tall (0.707 in), which the knob on it (0.675 in across) just fits. A regular eight-sided body of this height would be 0.846; wider than tall, then, by a tenth of an inch. With the tan kit's picture's reading of the flat's upper edge it would be 0.84: the ± covers it.
The armoured body, top to bottom1.692 in ± 0.014 in 43 mmProvisionalWorked out: {.body_top_above_axis} + {.body_bottom_below_axis}
Worked out 1.692 in ± 0.014 in used
{.body_top_above_axis} + {.body_bottom_below_axis}, harvested
The collar's pads: how far they stand out of the collar0.027 in ± 0.007 in 0.7 mmProvisionalPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 0.027 in ± 0.007 in used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by the top pad's top at row 384 (columns 658 to 1042); the collar ahead of it at rows 395 and 391 (columns 634 and 646) and behind it at 396 and 397 (columns 1066 and 1078): 12 px
Read where the top pad meets the picture's outline: the armour's front end, a collar an inch long, has a raised pad on its top, one on each side and one between each two; ahead of the top pad and behind it the collar's own skin shows, lower.
The pads round the collar7ProvisionalPhoto: the left side), 4bcd30bff255 (the right side), 1401ce09b146 and 4c5adfd48657 (Primary Arms' G45.NM_01 and _03, from above), 8bf71db67f7a (T.REX ARMS' 8483, the underside
Photo 7 count used
the left side), 4bcd30bff255 (the right side), 1401ce09b146 and 4c5adfd48657 (Primary Arms' G45.NM_01 and _03, from above), 8bf71db67f7a (T.REX ARMS' 8483, the underside, harvested
Scale: none needed: a count. Read by one on top, three on each side at the axis's height and 45 degrees above and below it, none underneath
Counted across the views, no one of which shows the whole turn: the top one in the outline of both side views and face on in Primary Arms' views from above (G45.NM_01, G45.NM_03); three down each side (EOTECH's left side view, Rifle Supply's right); none underneath, where the foot is (T.REX ARMS' picture of the parts laid out, 8483).
The collar's pads: their front ends behind the mount's centre0.176 in ± 0.015 in 4.5 mmProvisionalPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 0.176 in ± 0.015 in used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by the top pad's front end in the outline at column 655 (the outline reaches row 384 at 658), and the upper side pad's lit front rim at 650 to 660 on row 475; the top plate's middle at 578: 77 px
The collar's pads: their length along the housing0.889 in ± 0.02 in 22.6 mmProvisionalPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 0.889 in ± 0.02 in used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by columns 655 to 1045 (the top pad in the outline; the upper side pad's lit rims on row 475): 390 px
The collar's pads down each side: how much of the turn each takes34° ± 3°ProvisionalPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 34 deg ± 3 deg used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by the pads' outlines on the picture, unwrapped about the armour's middle (row 755) at the pads' radius (371 px): the upper one from row 445 to 610 (57 and 23 degrees up: 34 wide), the one at the axis's height from 670 to 890 (220 px about its own middle: 34). On the tan kit's picture (rows 555 to 700, and 760 to 960, at 410.5 px/in) they read 34 and 34
The three down a side read alike on EOTECH's two left side views, the black kit's and the tan's: 33 to 35 degrees each.
The collar's pad on top: how much of the turn it takes44° ± 5°ProvisionalPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 44 deg ± 5 deg used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by the top pad is seen edge on: its lower edge at row 413, unwrapped about the armour's middle (row 755) at the pads' radius (371 px): 67 degrees up, 23 short of the top each side. The tan kit's picture has it at 68
The sunk panel in each pad above and below the axis's height: its length along the housing0.787 in ± 0.02 in 20 mmProvisionalPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 0.787 in ± 0.02 in used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by the upper pad's panel, its two end walls at columns 675 and 1020: 345 px
The four pads 45 degrees above and below the axis's height have a panel sunk in their faces, a rim left round it; the pad on top and the two at the axis's height are plain (EOTECH's views from ahead, Midwest Gun Works' of the tan one).
The sunk panel in a pad: how much of the turn it takes22° ± 3°ProvisionalPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 22 deg ± 3 deg used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by the upper pad's panel from row 460 to 565, unwrapped about the armour's middle (row 755) at the pads' radius (371 px): 53 and 31 degrees up. The tan kit's picture reads 22 (rows 570 to 660)
The sunk panel in a pad: its depth0.027 in ± 0.015 in 0.7 mmProvisionalWorked out: {.collar_pad_relief}
Worked out 0.027 in ± 0.015 in used
{.collar_pad_relief}, harvested
Not read to better than a factor of two. A side view shows the panel's two walls only as bands: 16 and 12 px tall on the tan kit's picture (410.5 px/in), 56 and 35 degrees up the collar, which is 0.047 and 0.051 in were the walls square to the face, and less as they are sloped. Taken as the pad's own relief, which those bracket from above: the panel's floor is then the collar's skin.
The vertical adjustment's knob, across0.675 in ± 0.01 in 17.1 mmProvisionalPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 0.675 in ± 0.01 in used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by columns 1165 to 1460 at rows 318 and 378: 296 px. Rifle Supply's right side view reads 0.674 (343 px)
The vertical adjustment's knob: its axis behind the mount's centre1.675 in ± 0.015 in 42.5 mmProvisionalPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 1.675 in ± 0.015 in used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by the knob's middle at column 1312.5, the top plate's at 578: 734.5 px
The lugs round each adjustment knob8ProvisionalPhoto: Rifle Supply's EOG45STS_2_HR: the right side, in line, the riser fitted, 2000 px
Photo 8 count used
Rifle Supply's EOG45STS_2_HR: the right side, in line, the riser fitted, 2000 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (846 px: 509.2 px/in). What stands up the picture reads 2.3% under EOTECH's own view at that scale (the published height comes to 3.23 in on it), so lengths, a count and a knob seen face on are taken from it, and no height. Read by the knob marked R, face on in this view, unwrapped about its middle (column 692, row 698) into a strip of angle against radius: at radius 170 to 176 px eight lit lugs, their middles at 9, 51, 97, 142, 187, 232, 277 and 321 degrees, a dark notch between each two
Counted on the horizontal knob, the one view that shows a knob's whole turn; the vertical one is the same knob by the side views (two tiers of lugs, one over the other, with a groove between).
The notches between a knob's lugs: their depth0.035 in ± 0.01 in 0.9 mmProvisionalPhoto: Rifle Supply's EOG45STS_2_HR: the right side, in line, the riser fitted, 2000 px
Photo 0.035 in ± 0.01 in used
Rifle Supply's EOG45STS_2_HR: the right side, in line, the riser fitted, 2000 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (846 px: 509.2 px/in). What stands up the picture reads 2.3% under EOTECH's own view at that scale (the published height comes to 3.23 in on it), so lengths, a count and a knob seen face on are taken from it, and no height. Read by the knob marked R unwrapped about its middle (column 692, row 698): the lugs lit out to radius 179 px, the notches open down to 161
The notches between a knob's lugs: how much of the turn each takes24° ± 3°ProvisionalPhoto: Rifle Supply's EOG45STS_2_HR: the right side, in line, the riser fitted, 2000 px
Photo 24 deg ± 3 deg used
Rifle Supply's EOG45STS_2_HR: the right side, in line, the riser fitted, 2000 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (846 px: 509.2 px/in). What stands up the picture reads 2.3% under EOTECH's own view at that scale (the published height comes to 3.23 in on it), so lengths, a count and a knob seen face on are taken from it, and no height. Read by the knob marked R unwrapped about its middle: at radius 170 px each lug 21 to 24 degrees of the 45 from one to the next, each notch the rest
Where the knob's notches stood in the picture30° ± 3°ProvisionalPhoto: Rifle Supply's EOG45STS_2_HR: the right side, in line, the riser fitted, 2000 px
Photo 30 deg ± 3 deg used
Rifle Supply's EOG45STS_2_HR: the right side, in line, the riser fitted, 2000 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (846 px: 509.2 px/in). What stands up the picture reads 2.3% under EOTECH's own view at that scale (the published height comes to 3.23 in on it), so lengths, a count and a knob seen face on are taken from it, and no height. Read by the knob marked R unwrapped about its middle: the first notch's middle, from the direction of the muzzle toward the underside (between the lugs at 9 and 51 degrees)
A knob turns: this is only how it was set when photographed, taken so that the model is as pictured.
The horizontal adjustment's knob: its outer face right of the optical axis's vertical1.123 in ± 0.05 in 28.5 mmProvisionalWorked out: {.body_half_width} + {.height} - {.axis_above_clamp_bottom} - {.body_top_above_axis}
Worked out 1.1227 in ± 0.05 in used
{.body_half_width} + {.height} - {.axis_above_clamp_bottom} - {.body_top_above_axis}, harvested
Worked out, not read: the knob on the body's right is taken to stand as far out of its side flat as the same knob stands out of its top (the kit's height, less the axis's height over the clamp's bottom and the body's top over the axis: 0.231 in).
The flutes round the diopter ring20 ± 1ProvisionalPhoto: EOTECH's left side view) and 4bcd30bff255 (Rifle Supply's right side view
Photo 20 count ± 1 count used
EOTECH's left side view) and 4bcd30bff255 (Rifle Supply's right side view, harvested
Scale: none needed: angles about the ring's own axis, by its own radius in each picture. Read by the ring's brightness down its length, unwrapped about its middle (row 766.5, radius 331 px on the left view; 719 and 379 on the right): dark edges at 75, 57, 40 and 22 degrees above the axis and 22, 40, 58 below it on the left view; 59, 42, 23 and 6 above and 21, 39, 56 below on the right
Not a count of the whole turn: no view from behind is on file. The flutes' shadowed edges, unwrapped about the ring's axis on two side views, are 17.5 to 18 degrees apart over the 100 degrees of the ring each view reads well, which is 20 round the ring; 19 or 21 isn't excluded.
The diopter ring's flutes: how much of the turn each takes8° ± 3°ProvisionalPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 8 deg ± 3 deg used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by the ring unwrapped about its middle: the flutes' dark edges are a whole number of pitches apart on either side of the axis and 44 degrees across it, two pitches and a flute's width; each dark run 4 to 5 degrees
The diopter ring's flutes: their depth0.028 in ± 0.015 in 0.7 mmProvisionalWorked out: {eotech-g33.diopter_flute_depth}
Worked out 0.028 in ± 0.015 in used
{eotech-g33.diopter_flute_depth}, harvested
Not read on this ring: no flute stands at the outline in any view on file. Taken as the G33's ring's, a like ring, so that the flutes can be drawn at all; said in the part's approximations.
The eyepiece's glass, visible diameter0.92 in ± 0.08 in 23.4 mmProvisionalPhoto: Primary Arms' G45.STS_03: from behind and the left, above
Photo 0.92 in ± 0.08 in used
Primary Arms' G45.STS_03: from behind and the left, above, harvested
Scale: eotech-g45.eyepiece_ring_od: the ring's rear rim and the glass are two circles about one axis, a few tenths of an inch apart in depth, and each one's longest diameter in an oblique view is its own. Read by the ring's rear rim 642 px on its long axis (rows 260 to 902), the glass 390 (rows 390 to 775): 0.61 of the ring. The glass lies deeper than the rim and reads a little small
The objective's clear aperture0.984 in 25 mmCorroboratedPublished: KYGunCo, EOTech G45 5X QD Magnifier Tan (G45.STSTAN), a seller, read Oct 12, 2026
Published “Objective 25” used
KYGunCo, EOTech G45 5X QD Magnifier Tan (G45.STSTAN), a seller, read Oct 12, 2026 the page, harvested Oct 12, 2026
The seller's own row, its unit not stated: millimetres, as such a row is. The same table says "Size 34mm".
Photo 1.02 in ± 0.08 in
Rifle Supply's EOG45STS_1_HR: from ahead and the left, above, harvested
Scale: eotech-g45.objective_tube_od: the tube's front rim and the glass are two circles about one axis, and each one's longest diameter in an oblique view is its own. Read by the tube's front rim 665 px on its long axis (rows 545 to 1210), the glass that shows 450 (rows 630 to 1080): 0.68 of the tube
A stated figure, and the picture reads within 0.04 in of it; one seller, its unit not stated: provisional.
EOTECH states neither it nor an exit pupil. One seller's table has a row "Objective 25" with no unit; the glass that shows in a view from ahead is 0.68 of the tube across.
The STS mount's length (its top plate)1.661 in 42.2 mmConfirmedWorked out: {eotech-g33.sts_mount_length}
Worked out 1.6614 in used
{eotech-g33.sts_mount_length}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The STS mount's height (the clamp's bottom to the hinge knuckles' top)1.181 in 30 mmConfirmedWorked out: {eotech-g33.sts_mount_height}
Worked out 1.1811 in used
{eotech-g33.sts_mount_height}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The clamp's bottom below the rail's top0.37 in ± 0.035 in 9.4 mmProvisionalWorked out: {eotech-g33.clamp_below_rail}
Worked out 0.37 in ± 0.035 in used
{eotech-g33.clamp_below_rail}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The clamp's bottom in the part frame (y; the rail's top is 0)-0.37 in ± 0.035 in -9.4 mmProvisionalWorked out: -{.clamp_below_rail}
Worked out -0.37 in ± 0.035 in used
-{.clamp_below_rail}, harvested
Where the side profile's origin (the clamp's bottom) sits in the part frame.
The riser's top (the magnifier's foot's underside) above the clamp's bottom1.385 in ± 0.02 in 35.2 mmProvisionalWorked out: {eotech-g33.riser_top_above_clamp_bottom}
Worked out 1.385 in ± 0.02 in used
{eotech-g33.riser_top_above_clamp_bottom}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The mount's top plate: its top above the clamp's bottom1.1 in ± 0.012 in 27.9 mmProvisionalWorked out: {eotech-g33.plate_top_above_clamp_bottom}
Worked out 1.1 in ± 0.012 in used
{eotech-g33.plate_top_above_clamp_bottom}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The mount's top plate: its underside above the clamp's bottom0.866 in ± 0.012 in 22 mmProvisionalWorked out: {eotech-g33.plate_bottom_above_clamp_bottom}
Worked out 0.866 in ± 0.012 in used
{eotech-g33.plate_bottom_above_clamp_bottom}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The riser's length along the rail1.608 in ± 0.01 in 40.8 mmProvisionalWorked out: {eotech-g33.riser_length}
Worked out 1.608 in ± 0.01 in used
{eotech-g33.riser_length}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
Photo 1.612 in ± 0.01 in
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by columns 223 to 929 over rows 1134 to 1230: 707 px
The same riser; this picture reads it 0.004 in longer, inside both ±.
The riser's width across the rail0.75 in ± 0.05 in 19 mmProvisionalWorked out: {eotech-g33.riser_width}
Worked out 0.75 in ± 0.05 in used
{eotech-g33.riser_width}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The mount's top plate: its width across the rail, without the arm to the hinge0.64 in ± 0.05 in 16.3 mmProvisionalWorked out: {eotech-g33.plate_width}
Worked out 0.64 in ± 0.05 in used
{eotech-g33.plate_width}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The clamp base's top (the lever's top edge) above the clamp's bottom0.555 in ± 0.02 in 14.1 mmProvisionalWorked out: {eotech-g33.base_top_above_clamp_bottom}
Worked out 0.555 in ± 0.02 in used
{eotech-g33.base_top_above_clamp_bottom}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The clamp's length along the rail1.395 in ± 0.01 in 35.4 mmConflictWorked out: {eotech-g33.clamp_length}
Worked out 1.395 in ± 0.01 in used
{eotech-g33.clamp_length}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
Photo 1.418 in ± 0.01 in
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by the silhouette's lowest rows (1710 to 1722), columns 268 to 890: 622 px
The same mount, read on a picture with two published lengths in it. This picture's bottom edge reads 0.023 in more, 1.6%: the lever's foot shows at its ends here.
g33 and left differ by 0.023 in beyond what each states it is good to.
The quick-detach lever's tail end, behind the mount's centre (closed)1.318 in ± 0.02 in 33.5 mmConflictPhoto: eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px
Photo 1.318 in ± 0.02 in used
eotechinc.com's gallery, EOTECH-G45-Black-1: the left side, square on, in line, the riser fitted, 2049 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (728 px: 438.2 px/in) and eotech-g45.height from the knob's top to the clamp's bottom (1448 px: 438.9 px/in): two published sizes, one along the picture and one up it, one scale within 0.2% (438.5 px/in). Read by the lever's tail end at column 1156 (rows 1482 to 1690), the top plate's middle at 578: 578 px
Worked out 1.381 in ± 0.02 in
{eotech-g33.lever_tail_behind_base}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The model's lever is this picture's outline. EOTECH's picture of the G33 on the same mount has the tail 0.06 in further back: the lever itself is 3.7% longer there against the plate, the riser and the base, which keep one scale between the two pictures. Which of the two is the mount's isn't known.
left and g33 differ by 0.063 in beyond what each states it is good to.
The lever is on the rifle's left and lies along the clamp, its tail to the rear.
The quick-detach lever's underside above the clamp's bottom0.085 in ± 0.02 in 2.2 mmProvisionalWorked out: {eotech-g33.lever_bottom_above_clamp_bottom}
Worked out 0.085 in ± 0.02 in used
{eotech-g33.lever_bottom_above_clamp_bottom}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The quick-detach lever's thickness across the rail0.2 in ± 0.05 in 5.1 mmProvisionalWorked out: {eotech-g33.lever_thickness}
Worked out 0.2 in ± 0.05 in used
{eotech-g33.lever_thickness}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The clamp's left face (the lever's outer face), left of the rail's centre1 in ± 0.05 in 25.4 mmProvisionalWorked out: {eotech-g33.base_left_of_centre}
Worked out 1 in ± 0.05 in used
{eotech-g33.base_left_of_centre}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The mount's hinge axis above the clamp's bottom0.871 in ± 0.03 in 22.1 mmCorroboratedWorked out: {eotech-g33.hinge_axis_above_clamp_bottom}
Worked out 0.871 in ± 0.03 in used
{eotech-g33.hinge_axis_above_clamp_bottom}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The mount's hinge axis to the right of the rail's centre0.69 in ± 0.04 in 17.5 mmProvisionalWorked out: {eotech-g33.hinge_axis_right_of_centre}
Worked out 0.69 in ± 0.04 in used
{eotech-g33.hinge_axis_right_of_centre}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
On the rifle's right as EOTECH pictures the G45 too: its left side view has the lever toward the lens, and Rifle Supply's right side view the hinge, with the knob marked R.
The hinge pin's diameter0.316 in ± 0.02 in 8 mmProvisionalWorked out: {eotech-g33.hinge_pin_d}
Worked out 0.316 in ± 0.02 in used
{eotech-g33.hinge_pin_d}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The hinge knuckles' outside diameter0.62 in ± 0.03 in 15.7 mmProvisionalWorked out: {eotech-g33.hinge_knuckle_d}
Worked out 0.62 in ± 0.03 in used
{eotech-g33.hinge_knuckle_d}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The hinge's length along the rail (both knuckles and the barrel between them)1.394 in ± 0.01 in 35.4 mmProvisionalWorked out: {eotech-g33.hinge_block_length}
Worked out 1.394 in ± 0.01 in used
{eotech-g33.hinge_block_length}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
Photo 1.416 in ± 0.015 in
Rifle Supply's EOG45STS_2_HR: the right side, in line, the riser fitted, 2000 px, harvested
Scale: eotech-g45.sts_mount_length along the mount's top plate (846 px: 509.2 px/in). What stands up the picture reads 2.3% under EOTECH's own view at that scale (the published height comes to 3.23 in on it), so lengths, a count and a knob seen face on are taken from it, and no height. Read by columns 1203 to 1924 over rows 1386 to 1498 (the rear knuckle's rear face to the front one's front): 721 px
The same mount, read on EOTECH's own right side view of it; Rifle Supply's picture reads 0.02 in more at its plate's scale, 1.6%.
Each hinge knuckle's length along the rail0.37 in ± 0.012 in 9.4 mmProvisionalWorked out: {eotech-g33.hinge_knuckle_length}
Worked out 0.37 in ± 0.012 in used
{eotech-g33.hinge_knuckle_length}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The wall under the hinge: its inner face right of the rail's centre0.13 in ± 0.04 in 3.3 mmProvisionalWorked out: {eotech-g33.hinge_web_inner_right_of_centre}
Worked out 0.13 in ± 0.04 in used
{eotech-g33.hinge_web_inner_right_of_centre}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The hinge barrel's diameter (the plate's arm, between the knuckles)0.5 in ± 0.04 in 12.7 mmProvisionalWorked out: {eotech-g33.hinge_barrel_d}
Worked out 0.5 in ± 0.04 in used
{eotech-g33.hinge_barrel_d}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The clamp's adjustment nut on the mount's right face, across0.36 in ± 0.02 in 9.1 mmProvisionalWorked out: {eotech-g33.clamp_nut_d}
Worked out 0.36 in ± 0.02 in used
{eotech-g33.clamp_nut_d}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
The clamp's adjustment nut: its axis above the clamp's bottom0.32 in ± 0.02 in 8.1 mmProvisionalWorked out: {eotech-g33.clamp_nut_above_clamp_bottom}
Worked out 0.32 in ± 0.02 in used
{eotech-g33.clamp_nut_above_clamp_bottom}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
How far the magnifier swings to the side on its mount93.5° ± 3°ProvisionalWorked out: {eotech-g33.flip_angle}
Worked out 93.5 deg ± 3 deg used
{eotech-g33.flip_angle}, harvested
The same mount: EOTECH's page for the STS mount alone (9-G33STS) says "This is the standard mount that comes with the G33, G43 and G45." Read on EOTECH's pictures of the G33 on it: the sources are in the G33's ledger.
To the rifle's right as EOTECH pictures it. No page states the angle, and no pair of views of the G45 from behind is on file: it is the same mount's, read between EOTECH's two rear views of the G33 on it.
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Picatinny rail (MIL-STD-1913)
- Uppers
- Aero Precision M4E1 Enhanced Upper Receiver Stripped, Aero Precision M4E1 Threaded upper receiver, BCM M4 Upper Receiver Assembly (w/ Laser T-Markings), Expo Arms 7075 Stripped AR-15 Upper Receiver, Geissele Automatics Super Duty Stripped Upper Receiver, Nordic Components 22RB .22 LR upper, 16", Palmetto State Armory AR-15 Stripped Upper Receiver, Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12", Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16"
- Handguards
- Aero Precision AR15 10.3" R-ONE M-LOK handguard, Aero Precision AR15 12.7" R-ONE M-LOK handguard, Aero Precision AR15 15" Enhanced M-LOK Handguard, Gen 2, Aero Precision AR15 15" R-ONE M-LOK handguard, Aero Precision AR15 15" S-ONE M-LOK Handguard, Aero Precision AR15 16.6" R-ONE M-LOK handguard, Aero Precision AR15 7.3" R-ONE M-LOK handguard, Aero Precision AR15 9.3" R-ONE M-LOK handguard, BCM MCMR-10 (M-LOK® Compatible* Modular Rail), BCM MCMR-13 (M-LOK® Compatible* Modular Rail), BCM MCMR-15 (M-LOK® Compatible* Modular Rail), Expo Arms Free Float AR-15 Handguard - M-LOK - 15", Geissele Automatics 10.5" Super Modular Rail MK16 M-LOK, Geissele Automatics 13.5" Super Modular Rail MK16 M-LOK, Geissele Automatics 15" Super Modular Rail MK16 M-LOK, MAS Defense 12.62" NERO M-LOK FREE FLOAT, MAS Defense 15" NERO M-LOK FREE FLOAT, MAS Defense 9.87" NERO M-LOK FREE FLOAT, Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length), Midwest Industries Combat Rail One Piece Free Float Handguard, M-LOK™ (15")
- Frames
- Taurus TX22 Gen 2 frame
- Rail sections
- Magpul M-LOK® Aluminum Rail, 3 Slots, Magpul M-LOK® Aluminum Rail, 5 Slots, Magpul M-LOK® Aluminum Rail, 7 Slots, Magpul M-LOK® Aluminum Rail, 9 Slots, Magpul M-LOK® Polymer Rail, 11 Slots, Magpul M-LOK® Polymer Rail, 3 Slots, Magpul M-LOK® Polymer Rail, 5 Slots, Magpul M-LOK® Polymer Rail, 7 Slots, Magpul M-LOK® Polymer Rail, 9 Slots
Sight and magnifier
- Optics
- Aimpoint Duty RDS Red Dot Sight, Aimpoint Micro T-2 Red Dot Reflex Sight, Aimpoint Patrol Rifle Optic (PRO) Red Dot Reflex Sight - QRP2 Mount, EOTECH HWS EXPS3 holographic weapon sight, 1-Dot Speed Ring, Holosun ARO 2 MOA red dot (listed by Holosun as ARO-CORE-RD-2), Holosun EPS Carry enclosed pistol sight, 2 MOA red dot (EPS-CARRY-RD-2), Holosun HS510C Open Reflex MRS Solar QD Mount, SIG Sauer ROMEO-MSR GEN II red dot sight, 2 MOA red dot, SIG Sauer ROMEO5 GEN II 1x20mm Compact Illuminated Dot Sight, 2 MOA red dot
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- KYGUNCO $604.04 Tan Nov 21, 2026, in stock that day
- T.REX ARMS $607.75 Black Nov 21, 2026, in stock that day
- Primary Arms $609.99 Black Oct 29, 2026, in stock that day
- GRITR Sports $643.50 Tan Nov 21, 2026, in stock that day
- Silencer Shop $715.00 Black Nov 21, 2026, stock not said
- Impact Guns $755.00 Black Nov 21, 2026, in stock that day
- T.REX ARMS $572.00 Tan Nov 21, 2026, out of stock that day
- AR15Discounts $679.00 Black Nov 21, 2026, out of stock that day
- Rifle Supply $732.99 Black Nov 21, 2026, out of stock that day