Upper
Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16"
A dedicated 5.7x28mm upper for a mil-spec AR-15 lower: a blowback monobloc receiver of 7075 aluminium with its 16 in barrel, perforated brake on 1/2x28, bolt, handle and buffer, a 13-slot rail over the handle and an M-LOK handguard with 3-slot rails above and below its front end. FN's P90 magazine lies along its top (it ships with one), and it ejects down through the lower's magazine well, which stays empty. Primary Arms names the maker Panzer Arms (Classic Firearms: "AR57 Mfg."); no maker's page is on file.

- Weight
- 48 oz ± 8 oz Provisionalpublished: AR Five Seven Center (ar-57center.com), home page: Cartridge 5.7×28mm NATO Capacity 50 Rounds Upper Weight ~3 lbs Full Build ~6 lbs Barrel Options 12″ / 16″, a seller, read Oct 18, 2026
- Lowest price
- Sold in the Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16", not by itself
- Made for
- Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver converts any mil-spec AR-15 lower to fire 5.7x28mm ammunition (Primary Arms' description; its specifications: Caliber Gauge 5.7X28mm)
- Maker's number
- ULT0116
- Colour
- Black (placeholder)
- Drawn as
- modelled
- Maker's page
- primaryarms.com
In “AR57 16 in, 5.7x28”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Barrel length (the listing's own figure)16 in ± 0.5 in 406.4 mmCorroboratedPublished: Primary Arms, Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16" (ULT0116), Specifications, a seller, read Oct 18, 2026
Published “Barrel Length 16” used
Primary Arms, Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16" (ULT0116), Specifications, a seller, read Oct 18, 2026 the page, harvested Oct 18, 2026
Published “The barrel is 16 inches with a perforated muzzle brake attached on 1/2 x 28 threads making the overall length 18 inches”
Classic Firearms, AR57 16" Complete ULT M-LOK Upper Receiver 5.7x28 (ACC-AR57-ULT-57-UPPER, MPN AR57-ULT16), Product description, a seller, read Oct 18, 2026 the page, harvested Oct 18, 2026
Both sellers give 16; Primary Arms' specifications table is the listing's own figure.
The barrel with its brake on (the sellers' "overall length" of the barrel)18 in ± 0.5 in 457.2 mmProvisionalPublished: Classic Firearms, AR57 16" Complete ULT M-LOK Upper Receiver 5.7x28, Product description, a seller, read Oct 18, 2026
Published “The barrel is 16 inches with a perforated muzzle brake attached on 1/2 x 28 threads making the overall length 18 inches” used
Classic Firearms, AR57 16" Complete ULT M-LOK Upper Receiver 5.7x28, Product description, a seller, read Oct 18, 2026 the page, harvested Oct 18, 2026
Published “Barrel is 16", threaded 1/2x28 With perforated brake attached overall barrel length 18"”
Classic Firearms, AR57 16" Complete ULT M-LOK Upper Receiver 5.7x28, Specs, a seller, read Oct 18, 2026 the page, harvested Oct 18, 2026
The description and the specs on one page say the same. The brake as drawn is 1.51 long ahead of its shoulder (brake_rear_x to muzzle_end_x): the 2 in over the barrel's 16 can't all be the brake's, and where the barrel's 16 is counted from isn't said.
The receiver's back to the muzzle end24.563 in ± 0.031 in 623.9 mmProvisionalPublished: Classic Firearms, AR57 16" Complete ULT M-LOK Upper Receiver 5.7x28, Product description, a seller, read Oct 18, 2026
Published “The receiver and rail block measures just over 17 inches overall length; from the receiver back to the muzzle end, the total length is 24 9/16 inches.” used
Classic Firearms, AR57 16" Complete ULT M-LOK Upper Receiver 5.7x28, Product description, a seller, read Oct 18, 2026 the page, harvested Oct 18, 2026
Published “Complete overall length of receiver 24.5"”
Classic Firearms, AR57 16" Complete ULT M-LOK Upper Receiver 5.7x28, Specs, a seller, read Oct 18, 2026 the page, harvested Oct 18, 2026
The same page gives both; 24 9/16 is to the sixteenth and says what it runs between (the receiver's back to the muzzle end), 24.5 is the specs' rounding of it.
The receiver and its rails, one block with the handguard: its overall length as the seller gives it17 in ± 0.25 in 431.8 mmProvisionalPublished: Classic Firearms, AR57 16" Complete ULT M-LOK Upper Receiver 5.7x28, Product description, a seller, read Oct 18, 2026
Published “The receiver and rail block measures just over 17 inches overall length; from the receiver back to the muzzle end, the total length is 24 9/16 inches.” used
Classic Firearms, AR57 16" Complete ULT M-LOK Upper Receiver 5.7x28, Product description, a seller, read Oct 18, 2026 the page, harvested Oct 18, 2026
What it spans isn't said. Through the photo's camera: the receiver's rear face to the handguard's front lip 17.74, to the front block's rail's front end 16.94; the rail's rear overhang to the lip 18.84. None of these is "just over 17" but the second with batch 10's correction to the published length (17.11). Kept as the seller's words; nothing is drawn from it.
The brake's front end ahead of the takedown pin23.508 in ± 0.1 in 597.1 mmConflictWorked out: Read on 054c636f9e79 through the camera fitted to its own features of known size: the traced outline's x max (94.3 px, the brake's prongs; muzzle_end_x_pinframe) on the plane of the prongs' near side (0.28 in out of the centre plane, toward the lens). The fit's own one sigma there 0.034; refitted without each group of features in turn the front lands 23.49 to 23.60; a width 0.06 either side moves it 0.03. A radial distortion term fitted beside it (k1 -0.17 ± 0.04, the receiver rail's thirteen edges bowing by 0.3 px) puts the front at 23.81, but reads the brake 2.25 long where this camera without it and the 12 in's (no distortion, 0.013 ± 0.015) read the same brake 2.13: the term isn't borne out at the photo's edge, where the brake is. The ± is the spread of the readings beside it.
Worked out 23.9415 in ± 0.04 in
{.overall_length} + {std.ar15.upper_rear_face_x}, harvested
The published back-to-muzzle length from the receiver's rear face, which is the standard's (it stops ahead of the lower's buffer tower; the photo's rear face reads 0.04 further back, its near edge 0.45 in nearer the lens). The rail block overhangs behind it.
Worked out 23.508 in ± 0.1 in used
Read on 054c636f9e79 through the camera fitted to its own features of known size: the traced outline's x max (94.3 px, the brake's prongs; muzzle_end_x_pinframe) on the plane of the prongs' near side (0.28 in out of the centre plane, toward the lens). The fit's own one sigma there 0.034; refitted without each group of features in turn the front lands 23.49 to 23.60; a width 0.06 either side moves it 0.03. A radial distortion term fitted beside it (k1 -0.17 ± 0.04, the receiver rail's thirteen edges bowing by 0.3 px) puts the front at 23.81, but reads the brake 2.25 long where this camera without it and the 12 in's (no distortion, 0.013 ± 0.015) read the same brake 2.13: the term isn't borne out at the photo's edge, where the brake is. The ± is the spread of the readings beside it., harvested
Worked out 23.36 in ± 0.12 in
The 12 in upper's brake front through its own photo's camera (panzer-ar57-ult-12-upper.muzzle_end_x, 19.58: that camera's features reach to the front block, 3.3 in short of its brake, and its lens has no distortion) and the 4 in the two barrels differ by (16 and 12, their listings), less the 12 in's jam nut (its photo: 0.22 thick between the handguard's lip and the brake), which sets its brake that much further out on a thread of the same length. Without the nut's 0.22: 23.58. The two uppers' receivers and handguards are one part: the two cameras agree on the upper M-LOK row's foremost slot within 0.01 and on the magazine's room within 0.012., harvested
Worked out 23.68 in ± 0.15 in
Read on ar-57center.com's right view of the 16 in (a copy on file, 800 x 600: another photographer) through a camera fitted to its lug holes' near rims, its receiver rail's thirteen slots' near edges and its upper M-LOK row's five whole slots: its brake's prongs at 797.5 px. At 31 px/in the fit can't fix the lens's distance: held at each distance from 26 to 125 in the front reads 23.86 to 23.54, the M-LOK row's foremost slot 16.27 to 16.28; at 40 to 60 in, which the light seen through its holes gives (3.2 and 2.3 px narrower than the holes), 23.73 to 23.64. Its pins alone, read as a flat frame, give 23.93: that photo's muzzle stands nearer its lens (the rail reads 30.9 px/in, the M-LOK row 31.7)., harvested
Worked out 23.73 in ± 0.1 in
US 2011/0168009 A1 (Robb and Royce, the first-generation AR-57's application; the user's copy, a copy on file), FIG. 5, drawn to scale by its own holes (each 0.25 in across against the pin spacing, 98.4 px/in at 150 dpi): the barrel's breech face 6.15 in ahead of the takedown pin, 0.22 behind the pivot; FIG. 6B has it 2.16 ahead of the magazine's rear end. This upper's 16 in barrel from there is 22.15 to its crown; its brake (2.13 long, the two cameras) is threaded on with the crown 0.5 to 0.6 inside it (a 1/2-28 muzzle thread's usual length, assumed): 23.68 to 23.78. The ULT is the second generation: where its breech is isn't drawn., from the site owner
The photo the model is drawn from, read through a camera on its own features of known size; the other photos and the first generation's drawing put the brake's front at 23.36 to 23.73, and none at the seller's 24 9/16 from the receiver's back (derived: 23.94), which stays beside them: what it is counted from isn't said, and the same page's "just over 17 inches" for the receiver and rail block (monobloc_length) doesn't fit one reading of either.
derived and camera differ by 0.434 in beyond what each states it is good to.
derived and twelve differ by 0.582 in beyond what each states it is good to.
derived and center differ by 0.262 in beyond what each states it is good to.
derived and patent differ by 0.212 in beyond what each states it is good to.
camera and patent differ by 0.222 in beyond what each states it is good to.
twelve and center differ by 0.32 in beyond what each states it is good to.
twelve and patent differ by 0.37 in beyond what each states it is good to.
The brake's front end as Primary Arms' left view reads it in its pin frame (the outline's map's other end: muzzle_end_x)23.325 in ± 0.012 in 592.5 mmProvisionalPhoto: Primary Arms ULT0116_02.jpg, the left side straight on, 2200 x 1467
Photo 23.325 in ± 0.012 in used
Primary Arms ULT0116_02.jpg, the left side straight on, 2200 x 1467, harvested
Scale: the lug holes' centres (takedown 1965.2, 826.8; pivot 1453.9, 826.4 px) as std.ar15.pin_spacing: 80.21 px/in. Read by the traced outline's x max (profiles.side): the brake's prongs at 96 px
How many slots the receiver's top rail has13CorroboratedPhoto: a photo on file
Photo 13 count used
a photo on file, harvested
Scale: none: a count. Read by 14 teeth along the rail on a 3x crop of fe9d442f7b56, the gaps between them the slots; 13 gaps between the 14 tooth runs along row 630 of 054c636f9e79; 14 teeth from above in 0bde48a31171
Published “The sight system is a 13 slot Picatinny over the operating handle, with 3-slot upper and lower forward rails.”
Classic Firearms, AR57 16" Complete ULT M-LOK Upper Receiver 5.7x28, Product description, a seller, read Oct 18, 2026 the page, harvested Oct 18, 2026
Published “13-slot Picatinny rail over the operating handle, plus 3-slot upper and lower forward rails”
Primary Arms, AR57 Ultra Light Tactical (ULT0116), Features, a seller, read Oct 18, 2026 the page, harvested Oct 18, 2026
Counted; the two sellers say the same.
How many slots each forward rail (on the front block's top, and under it) has3CorroboratedPhoto: a photo on file
Photo 3 count used
a photo on file, harvested
Scale: none: a count. Read by four teeth with three gaps on the front block's top (row 630 of 054c636f9e79, 662 to 789 px) and on its underside; three slots on the top rail from ahead in b894132847e8
Published “with 3-slot upper and lower forward rails”
Classic Firearms, AR57 16" Complete ULT M-LOK Upper Receiver 5.7x28, Product description, a seller, read Oct 18, 2026 the page, harvested Oct 18, 2026
Counted; the seller says the same.
The rear rail's top above the pin line2.545 in ± 0.015 in 64.6 mmProvisionalPhoto: a photo on file
Photo 2.545 in ± 0.015 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the tooth tops of the traced outline over x -1.5 to 3.4 (623 px, the same row as the front rail's tooth tops 15 in ahead: the photo is level); the rail's near edge, 0.42 in nearer the lens than the pins, reads at most 0.01 high from the lens's distance the yaw implies
The front block's rail top above the pin line2.54 in ± 0.015 in 64.5 mmProvisionalPhoto: a photo on file
Photo 2.54 in ± 0.015 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the tooth tops of the traced outline over x 15.0 to 16.2 (623 px)
The rear rail's rearmost slot's centre ahead of the takedown pin (negative: behind it)-1.248 in ± 0.015 in -31.7 mmConflictWorked out: Read on 054c636f9e79 through the camera fitted to it (the header): the thirteen slots' front edges on the rail's near face (the left edges of the gaps along rows 626 to 632, 1676.5 to 2056.0 px: 31.63 px apart, 0.3943 in in the pin frame, the standard's pitch) fitted with the rest of the camera, on MIL-STD-1913's pitch and slot width; one sigma 0.013.
Photo -1.163 in ± 0.02 in
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the gap between the rearmost two teeth along row 630, 2056 to 2061 px, its centre 2058.5 px. The thirteen gaps' centres run 2058.5 to 1685 px: 31.1 px apart, 0.388 in, 1.5% short of the standard's 0.394 (the rail drawn has the standard's pitch from this slot)
A gap's middle, where the backdrop shows through the slot: the line of sight crosses the rail at an angle growing away from the lens, so the gap seen is cut down from one side, 16.8 px wide at the rail's front and 5.8 at its rear, and its middle moves by half of that.
Worked out -1.248 in ± 0.015 in used
Read on 054c636f9e79 through the camera fitted to it (the header): the thirteen slots' front edges on the rail's near face (the left edges of the gaps along rows 626 to 632, 1676.5 to 2056.0 px: 31.63 px apart, 0.3943 in in the pin frame, the standard's pitch) fitted with the rest of the camera, on MIL-STD-1913's pitch and slot width; one sigma 0.013., harvested
The slots' near edges, which the view across the rail doesn't move; the gaps' middles read the rail 1.5% short and its first slot 0.085 in forward.
photo and camera differ by 0.085 in beyond what each states it is good to.
The front block's top rail: its rearmost slot's centre ahead of the takedown pin15.282 in ± 0.02 in 388.2 mmProvisionalWorked out: Read on 054c636f9e79 through the camera fitted to it (the header): the front rail's teeth along rows 626 to 628, each tooth's near face from its front edge (where the backdrop ends: 691.2, 722.1, 753.1 px) to its rear edge (where its lit rear face begins: 674.9, 705.6, 736.5 px), and the rear faces' far ends (685.4, 715.7, 745.9 px), on MIL-STD-1913's pitch and slot width; one sigma 0.016. Batch 10 read the gap's middle at 747 px (15.188 in the pin frame) and its yaw correction made it 15.394; through the camera that middle is 15.252, the gap seen being cut down from one side by the view across the rail.
Worked out 15.282 in ± 0.02 in used
Read on 054c636f9e79 through the camera fitted to it (the header): the front rail's teeth along rows 626 to 628, each tooth's near face from its front edge (where the backdrop ends: 691.2, 722.1, 753.1 px) to its rear edge (where its lit rear face begins: 674.9, 705.6, 736.5 px), and the rear faces' far ends (685.4, 715.7, 745.9 px), on MIL-STD-1913's pitch and slot width; one sigma 0.016. Batch 10 read the gap's middle at 747 px (15.188 in the pin frame) and its yaw correction made it 15.394; through the camera that middle is 15.252, the gap seen being cut down from one side by the view across the rail., harvested
The front block's lower rail: its rearmost slot's centre ahead of the takedown pin15.51 in ± 0.04 in 394 mmProvisionalWorked out: Read on 054c636f9e79 (the gap between the lower rail's two rearmost teeth, 718 to 733 px, centre 726 px: 15.45 in the pin frame) through the camera fitted to it (the header), on the rail's near face: 15.48; and moved forward by what the same reading does on the front block's top rail (its gap's middle through the camera, 15.252, against its teeth's near edges, 15.282).
Worked out 15.51 in ± 0.04 in used
Read on 054c636f9e79 (the gap between the lower rail's two rearmost teeth, 718 to 733 px, centre 726 px: 15.45 in the pin frame) through the camera fitted to it (the header), on the rail's near face: 15.48; and moved forward by what the same reading does on the front block's top rail (its gap's middle through the camera, 15.252, against its teeth's near edges, 15.282)., harvested
The lower forward rail's face (its tooth tops, facing down) above the pin line (negative: below)-0.093 in ± 0.01 in -2.4 mmProvisionalWorked out: Read on a copy on file through the camera fitted to it (the header; 2026-10-20): the teeth's faces along row 834.6 (columns 640 to 745, x 15.6 to 16.4) on the near edge of the rail's flat (0.328 out): -0.093 to -0.094; the slots' floors along row 824.6 read 0.031, 0.124 above them (MIL-STD-1913's .118 +.008).
Photo -0.11 in ± 0.02 in
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the traced outline's lowest run over x 15.3 to 16.3 (835 px)
Worked out -0.093 in ± 0.01 in used
Read on a copy on file through the camera fitted to it (the header; 2026-10-20): the teeth's faces along row 834.6 (columns 640 to 745, x 15.6 to 16.4) on the near edge of the rail's flat (0.328 out): -0.093 to -0.094; the slots' floors along row 824.6 read 0.031, 0.124 above them (MIL-STD-1913's .118 +.008)., harvested
Through the photo's camera at the edge the silhouette is, the slots' depth the standard's. The 12 in's photo reads it -0.150 as the near edge and -0.080 as the far one.
The receiver's rear face behind the takedown pin (negative)-0.621 in ± 0.005 in -15.8 mmConflictWorked out: {std.ar15.upper_rear_face_x}
Worked out -0.621 in ± 0.005 in used
{std.ar15.upper_rear_face_x}, harvested
The standard's: an upper that fits a mil-spec lower stops ahead of its buffer tower.
Photo -0.663 in ± 0.02 in
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the traced outline's rear face over y 0.6 to 1.5 (2018 to 2020 px)
The face's near edge, 0.45 in nearer the lens than the pins: from the 60 in the yaw and the M-LOK pitch imply, 0.04 behind where the face is.
The standard's place is where a receiver that fits the lower must stop; the photo's 0.04 in more is the size perspective gives its near edge.
std and photo differ by 0.042 in beyond what each states it is good to.
The rail block's rear end (the rail overhangs the receiver)-1.723 in ± 0.02 in -43.8 mmProvisionalPhoto: a photo on file
Photo -1.723 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the traced outline's x min (2103 px)
The rail block's rear end as the trace's frame reads it (the outline's map behind the takedown pin: rail_rear_x)-1.723 in ± 0.02 in -43.8 mmProvisionalWorked out: {.rail_rear_x}
Worked out -1.723 in ± 0.02 in used
{.rail_rear_x}, harvested
The same reading: through the photo's camera the rail's rear end is -1.725 (2103 px on the rail's near face), and the outline behind the takedown pin is taken as read.
The rear rail's front end (its front tooth's face) ahead of the takedown pin3.978 in ± 0.02 in 101 mmProvisionalPhoto: a photo on file
Photo 3.978 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the front tooth's run along row 626, 1646 to 1676 px: its front face 1646 px
The rear rail block's front face, flush with its rail's front end (the magazine's latch stands out of it)3.97 in ± 0.02 in 100.8 mmConflictWorked out: Read on a copy on file through the camera fitted to it (the header; 2026-10-19 (night), a working script): above the magazine's top round the face shows as a light band between its corners, 1640.6 to 1645.6 px along rows 646 to 652, white ahead of it to the magazine's end: its far corner (riser_width / 2 out, beyond the centre plane) 3.971, its near corner 3.966. The lens 43 in off and nearly square, the depth moves it 0.01 at most.
Photo 4.04 in ± 0.03 in
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the block's front face on a 3x crop, 1640 to 1641 px, under the rail's front tooth
Worked out 3.97 in ± 0.02 in used
Read on a copy on file through the camera fitted to it (the header; 2026-10-19 (night), a working script): above the magazine's top round the face shows as a light band between its corners, 1640.6 to 1645.6 px along rows 646 to 652, white ahead of it to the magazine's end: its far corner (riser_width / 2 out, beyond the centre plane) 3.971, its near corner 3.966. The lens 43 in off and nearly square, the depth moves it 0.01 at most., harvested
The face where it stands, through the photo's camera; the 12 in's photo, through its own, has 3.98.
photo and camera differ by 0.07 in beyond what each states it is good to.
2026-10-19 (night): the magazine's round end doesn't bear on this face. Through each upper's own camera the face stands 0.10 in behind the magazine's rearmost point (this upper's photo: 3.97 against 4.070; the 12 in's: 3.98 against 4.082), white between the two above and below the latch (latch_bottom_y, latch_top_y), which stands out of the face into the notch in the magazine's round end (fn-p90-50-magazine's own side photo, 76c0d7572a37, has the notch). The face is flush with the rail's front end (rail_front_x, 3.978). The pin frame's reading (photo) is the face's far corner: kept as read.
The receiver's top either side of the rail block (the step it rises from)1.59 in ± 0.03 in 40.4 mmProvisionalPhoto: a photo on file
Photo 1.59 in ± 0.03 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the traced outline's top behind the rail's overhang (x -0.9 to -0.7: 1.59): the receiver's top at its rear, under the rail block's ramp
The handguard's top (the magazine lies on it) above the pin line1.6 in ± 0.01 in 40.6 mmConflictWorked out: {.mag_underside_y}
Photo 1.566 in ± 0.02 in
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the magazine's underside, 701 px, with no light between it and the handguard from 877 px back (columns 880 to 1420 dark from the magazine's top to the M-LOK slots); ahead of 877 px the handguard's top ramps down to 717 px (1.367) under the magazine's front end, where light shows between them, and the outline has that ramp
Worked out 1.6 in ± 0.01 in used
{.mag_underside_y}, harvested
The magazine lies on it, no light between them from 877 px back: one plane for both (a seat drawn bearing). The model clamps the traced outline's run under the magazine to it (the trace, cut at 699 px, gives 1.576 to 1.584).
The seat is the magazine's underside, read where light shows under it; the outline's top there is the cut the trace was made with, 0.02 under it.
photo and seat differ by 0.034 in beyond what each states it is good to.
The handguard's top at its lowest, where it ramps down ahead of the magazine's underside to the front block1.367 in ± 0.02 in 34.7 mmProvisionalPhoto: a photo on file
Photo 1.367 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the light under the magazine's front end on a 3x crop: its lower edge at 717 px from 780 px back to where it closes at 877 px
The handguard's inside is drawn under this, a wall below it: the dip isn't an opening (no light is seen into the handguard there).
Where the handguard's top begins its ramp down to the front block, ahead of the takedown pin13.6 in ± 0.06 in 345.4 mmProvisionalWorked out: Read on a 3x crop of 054c636f9e79 where the light under the magazine's front end closes, 877 px (13.567 in the pin frame), through the camera fitted to it (the header) at the upper chamfer's top (0.42 in out).
Worked out 13.6 in ± 0.06 in used
Read on a 3x crop of 054c636f9e79 where the light under the magazine's front end closes, 877 px (13.567 in the pin frame), through the camera fitted to it (the header) at the upper chamfer's top (0.42 in out)., harvested
The receiver's underside above the pin line (it sits on the lower's deck)0.248 in ± 0.0015 in 6.3 mmConfirmedWorked out: {std.ar15.deck_y}
Worked out 0.2485 in ± 0.0015 in used
{std.ar15.deck_y}, harvested
Photo 0.25 in ± 0.012 in
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the traced outline's lower edge over x 1.0 to 6.0 (806 px)
The seat is the lower's deck; the photo agrees within 0.002 in.
The takedown lug's front face ahead of the takedown pin (the lug under the receiver, at the lower's rear slot)0.22 in ± 0.01 in 5.6 mmProvisionalWorked out: Read on a copy on file through the camera fitted to it (the header; 2026-10-20): the lug's front face, turned toward the lens (over x 7.9), shows as a light band 7 px wide, 1940.7 to 1947.8 px along rows 808 to 838: its far edge (the silhouette, the lug's half width beyond the centre plane) reads 0.220 to 0.223 and its near edge 0.219 to 0.222. Its rear face (the near edge, 1983.4 px) reads -0.220 to -0.223: the lug 0.44 long, centred on its pin. The traced outline, the silhouette read as a near edge, has its front at 0.308. The 12 in's photo through its own camera reads its front face's two edges 0.216 to 0.226.
Worked out 0.22 in ± 0.01 in used
Read on a copy on file through the camera fitted to it (the header; 2026-10-20): the lug's front face, turned toward the lens (over x 7.9), shows as a light band 7 px wide, 1940.7 to 1947.8 px along rows 808 to 838: its far edge (the silhouette, the lug's half width beyond the centre plane) reads 0.220 to 0.223 and its near edge 0.219 to 0.222. Its rear face (the near edge, 1983.4 px) reads -0.220 to -0.223: the lug 0.44 long, centred on its pin. The traced outline, the silhouette read as a near edge, has its front at 0.308. The 12 in's photo through its own camera reads its front face's two edges 0.216 to 0.226., harvested
Both edges of the face agree, and the other upper's photo through its own camera reads the same; the model's lug is cut to it, the outline's front being the face's far edge read as its near one.
The handguard's underside above the pin line0.098 in ± 0.01 in 2.5 mmProvisionalWorked out: Read on a copy on file through the camera fitted to it: the outline's lower edge at 818.8 to 819.8 px along columns 1000 to 1250 (x 8.9 to 12.1), on the keel's near side (keel_width / 2): the lens, 0.57 above the pin line, sees the underside's near edge, which is the silhouette there: 0.093 to 0.103.
Photo 0.088 in ± 0.015 in
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the traced outline's lower edge over x 7.5 to 14 (819 px)
Worked out 0.098 in ± 0.01 in used
Read on a copy on file through the camera fitted to it: the outline's lower edge at 818.8 to 819.8 px along columns 1000 to 1250 (x 8.9 to 12.1), on the keel's near side (keel_width / 2): the lens, 0.57 above the pin line, sees the underside's near edge, which is the silhouette there: 0.093 to 0.103., harvested
Through the photo's camera at the edge the silhouette is. The 12 in's photo, from a lens 2.6 in under the pin line, reads the same underside 0.058 as its near edge and 0.135 as its far edge, which is the silhouette from below: this one between them. An underside seen from below shows its far edge, a face turned toward the lens its far edge, and a lens above a part sees an underside's near edge (2026-10-20: the 12 in's close photo, 2.6 in under the pin line, read both ways brackets this one's).
The handguard's front end (the front block's lip round the barrel) ahead of the takedown pin17.12 in ± 0.07 in 434.8 mmProvisionalWorked out: Read on 054c636f9e79 where the outline's lip meets the barrel (17.05 in the pin frame, 597 px: handguard_front_x_pinframe) through the camera fitted to it (the header), at the keel's depth (0.42 in out): 17.12, where the outline's map puts its clipped end (17.134); at the side face's depth (0.72 out) the same pixel is 17.05. The ± spans the two.
Worked out 17.12 in ± 0.07 in used
Read on 054c636f9e79 where the outline's lip meets the barrel (17.05 in the pin frame, 597 px: handguard_front_x_pinframe) through the camera fitted to it (the header), at the keel's depth (0.42 in out): 17.12, where the outline's map puts its clipped end (17.134); at the side face's depth (0.72 out) the same pixel is 17.05. The ± spans the two., harvested
The handguard's front end as Primary Arms' left view reads it in its pin frame (where the traced outline is clipped: the barrel and brake are the model's)17.05 in ± 0.02 in 433.1 mmProvisionalPhoto: a photo on file
Photo 17.05 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by where the outline's lip meets the barrel's run (597 px)
The front block's rear face (the magazine's front cap stands against it), ahead of the takedown pin15 in ± 0.05 in 381 mmProvisionalWorked out: Read on 054c636f9e79 (a 3x crop: the block's rearmost tooth runs back to 767 px, where the magazine's front cap covers it: 14.938 in the pin frame) through the camera fitted to it (the header), on the rail's near face: 14.998.
Worked out 15 in ± 0.05 in used
Read on 054c636f9e79 (a 3x crop: the block's rearmost tooth runs back to 767 px, where the magazine's front cap covers it: 14.938 in the pin frame) through the camera fitted to it (the header), on the rail's near face: 14.998., harvested
The front block's rear face at the magazine's body's height, where the cap's body stands against it (ahead of the takedown pin); the rail's rear tooth reaches further back over the magazine's top (front_block_rear_x)14.939 in ± 0.05 in 379.5 mmConflictWorked out: {.mag_rear_x} + {fn-p90-50-magazine.length}
Worked out 14.939 in ± 0.03 in
Read on 054c636f9e79 along rows 640, 655, 670 and 685 px (each the median of three): a dark line at 763 px between the block's grey (72 to 76) and the cap's (85 to 106), 14.988 in the pin frame, through the camera fitted to it (the header) on the cap's near side (half fn-p90-50-magazine.cap_width out): the lens's foot is behind the block (x 7.9), so the cap's near side, standing out past the riser, covers it, and the line is the cap's front edge where it stands against the block. At the riser's side the same pixel is 15.04 (this session's first reading); batch 12 had 15.19 through the yaw correction to the published length., harvested
Worked out 15.01 in ± 0.04 in
The traced outline's block face (profiles.side: 14.947 to 14.954 in the pin frame from 1.38 to 2.54 above the pins, the trace's threshold edge about 766 px) through the outline's map (the header): 15.010 (the camera at the riser's side: 15.002)., harvested
Worked out 14.939 in ± 0.05 in used
{.mag_rear_x} + {fn-p90-50-magazine.length}, harvested
Where the magazine's cap stands, its rear end on the latch: the face drawn bearing on it (a seat is drawn bearing).
The magazine (fn-p90-50-magazine.length, its two ends through both uppers' cameras) stands with its cap against this face and its round end on the latch: the face is drawn where its cap stands, on the cap's front edge read through this photo's camera (photo). The traced outline's face (outline, 15.01 through its map) stands 0.07 ahead of it: the block is filled out to the seat below the magazine's top.
photo and outline differ by 0.071 in beyond what each states it is good to.
Detail pass, 2026-10-18 (the magazine's owner read the 12 in's at 1669 px): the cap's lugs stand at its two sides with a gap between them as wide as the rail (fn-p90-50-magazine.cap_lug_width), and the block's rearmost tooth runs back between them over the magazine's top. Drawn so: the block cut back to this face below the magazine's top.
Bore axis above the takedown pin centre0.957 in ± 0.02 in 24.3 mmProvisionalPhoto: a photo on file
Photo 0.957 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the middle of the barrel's dark run in columns 270 to 560 px (728 to 770 px: 749 px), ahead of the handguard; the photo level (the pins within 0.4 px, the two rails' tops on one row)
0.08 in above a mil-spec upper's (std.ar15.bore_axis_y, 0.8775): this upper's bore isn't the standard's; its buffer, in the lower's tube, is on the tube's axis.
The barrel's diameter ahead of the handguard0.53 in ± 0.025 in 13.5 mmProvisionalWorked out: Read on 054c636f9e79: the barrel's dark run in columns 270 to 560 px is 42 px (0.524 in the pin frame); the camera fitted to the photo (the header) has 79.7 px/in across the barrel there (batch 10: 76.2, its yaw correction's slope at x 20, and 0.55). A glossy black tube reads up to 3% thin on white: in the ±.
Worked out 0.53 in ± 0.025 in used
Read on 054c636f9e79: the barrel's dark run in columns 270 to 560 px is 42 px (0.524 in the pin frame); the camera fitted to the photo (the header) has 79.7 px/in across the barrel there (batch 10: 76.2, its yaw correction's slope at x 20, and 0.55). A glossy black tube reads up to 3% thin on white: in the ±., harvested
The brake's rear face (the barrel's shoulder it seats on) ahead of the takedown pin21.38 in ± 0.05 in 543.1 mmProvisionalWorked out: Read on 054c636f9e79 (a 2x crop: the brake's rear band begins at 262 px, 21.234 in the pin frame) through the camera fitted to it (the header), on the brake's near side (0.3 in out): 21.375. The brake is then 2.13 long to its front end (muzzle_end_x).
Worked out 21.38 in ± 0.05 in used
Read on 054c636f9e79 (a 2x crop: the brake's rear band begins at 262 px, 21.234 in the pin frame) through the camera fitted to it (the header), on the brake's near side (0.3 in out): 21.375. The brake is then 2.13 long to its front end (muzzle_end_x)., harvested
The brake's rear band (a plain collar behind its ports): its front end, where a groove parts it from the ported body21.88 in ± 0.04 in 555.8 mmProvisionalWorked out: Read on 054c636f9e79 (a 2x crop: the groove at 222 px, 21.733 in the pin frame) through the camera fitted to it (the header), on the brake's near side: 21.881.
Worked out 21.88 in ± 0.04 in used
Read on 054c636f9e79 (a 2x crop: the groove at 222 px, 21.733 in the pin frame) through the camera fitted to it (the header), on the brake's near side: 21.881., harvested
The brake's rearmost column of ports: its centre ahead of the takedown pin22.32 in ± 0.03 in 566.9 mmProvisionalWorked out: Read on 054c636f9e79 (along row 742 the three ports are dark from 181-195, 162-175 and 142-155 px: centres 188, 168.5, 148.5 px; 22.157 in the pin frame) through the camera fitted to it (the header), on the brake's near side: 22.316, 22.563, 22.816.
Worked out 22.32 in ± 0.03 in used
Read on 054c636f9e79 (along row 742 the three ports are dark from 181-195, 162-175 and 142-155 px: centres 188, 168.5, 148.5 px; 22.157 in the pin frame) through the camera fitted to it (the header), on the brake's near side: 22.316, 22.563, 22.816., harvested
The ports' columns, centre to centre0.25 in ± 0.01 in 6.3 mmProvisionalWorked out: Read on 054c636f9e79: the three centres through the camera fitted to it (the header), 22.316, 22.563, 22.816: 0.250 apart (19.75 px at its 78.9 px/in there; batch 10 had 75.5 by its yaw correction, and 0.262).
Worked out 0.25 in ± 0.01 in used
Read on 054c636f9e79: the three centres through the camera fitted to it (the header), 22.316, 22.563, 22.816: 0.250 apart (19.75 px at its 78.9 px/in there; batch 10 had 75.5 by its yaw correction, and 0.262)., harvested
A port's diameter0.171 in ± 0.015 in 4.3 mmProvisionalWorked out: Read on 054c636f9e79: the ports at the side of the brake are 13 to 14 px across along x (rows 742 to 766), at the camera's 78.9 px/in there (the header; batch 10: 75.5 and 0.179).
Worked out 0.171 in ± 0.015 in used
Read on 054c636f9e79: the ports at the side of the brake are 13 to 14 px across along x (rows 742 to 766), at the camera's 78.9 px/in there (the header; batch 10: 75.5 and 0.179)., harvested
How many columns of ports along the brake3ProvisionalPhoto: a photo on file
Photo 3 count used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by three ports along each row of 054c636f9e79 and of b894132847e8
How many ports round the brake in each column6ProvisionalPhoto: a photo on file
Photo 6 count used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by three rows show on the half facing the lens, their centres at 741.5 and 764.5 px and a sliver at 728 to 730 px about the brake's axis at 748.5 px (radius 23.5 px): 17 degrees above the side, 43 below and 77 above, 60 degrees apart: six round, one every 60 degrees. The count of the far half is inferred from the spacing
Where the ports are clocked: the row nearest the left side's middle, in degrees above it17ProvisionalPhoto: a photo on file
Photo 17 count used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by as brake_ports_around: asin(7 / 23.5). A threaded brake stops where its thread times it; the photo's is drawn
Degrees, held as a count.
The slot across the brake's front end: how deep it runs back from the front0.43 in ± 0.03 in 10.9 mmProvisionalWorked out: Read on 054c636f9e79: light through the front end between 740 and 758 px from 96 to 130 px (columns 97 to 125 have two dark runs, 135 one): 34 px at the camera's 78.9 px/in along the brake there (the header; batch 10: 75.5 and 0.45).
Worked out 0.43 in ± 0.03 in used
Read on 054c636f9e79: light through the front end between 740 and 758 px from 96 to 130 px (columns 97 to 125 have two dark runs, 135 one): 34 px at the camera's 78.9 px/in along the brake there (the header; batch 10: 75.5 and 0.45)., harvested
The slot's height (it runs across, side to side)0.226 in ± 0.02 in 5.7 mmProvisionalWorked out: Read on 054c636f9e79: 18 px (740 to 758 px) at the camera's 79.7 px/in across the brake there (the header; batch 10: 75.5 and 0.24).
Worked out 0.226 in ± 0.02 in used
Read on 054c636f9e79: 18 px (740 to 758 px) at the camera's 79.7 px/in across the brake there (the header; batch 10: 75.5 and 0.24)., harvested
The brake's diameter0.59 in ± 0.025 in 15 mmProvisionalWorked out: Read on 054c636f9e79: 47 px (725 to 772 px) in columns 210 to 250, at the camera's 79.7 px/in across the brake there (the header; batch 10: 75.5, its yaw correction's slope at x 22.5, and 0.62).
Worked out 0.59 in ± 0.025 in used
Read on 054c636f9e79: 47 px (725 to 772 px) in columns 210 to 250, at the camera's 79.7 px/in across the brake there (the header; batch 10: 75.5, its yaw correction's slope at x 22.5, and 0.62)., harvested
M-LOK slots in the upper row on each side6ProvisionalPhoto: the left side); 9d225b7d85c8 (the right side, ar-57center.com
Photo 6 count used
the left side); 9d225b7d85c8 (the right side, ar-57center.com, harvested
Scale: none: a count. Read by six slots in the upper row on the left, the foremost under the front block; six on the right in the smaller photo
M-LOK slots in the lower row on each side (staggered between the upper row's)5ProvisionalPhoto: a photo on file
Photo 5 count used
a photo on file, harvested
Scale: none: a count. Read by five see-through slots along row 790 (gaps at 689-772, 810-898, 931-1023, 1055-1150, 1178-1277 px), each midway between two of the upper row's
The upper row's foremost slot's centre ahead of the takedown pin16.32 in ± 0.02 in 414.5 mmProvisionalWorked out: Read on 054c636f9e79 through the camera fitted to it (the header): the five whole slots behind the foremost (their dark runs' middles along rows 738 to 740 and 753 to 755: 781.9, 907.4, 1033.7, 1160.9, 1288.6 px) on Magpul's 40 mm pitch and the side face's plane (handguard_width), fitted with the camera: the foremost's centre 16.321, one sigma 0.011. The foremost slot itself (608 to 708 px, partly hidden, its middle 658 px) reads 16.287 through the camera; batch 10's yaw correction made it 16.544.
Worked out 16.32 in ± 0.02 in used
Read on 054c636f9e79 through the camera fitted to it (the header): the five whole slots behind the foremost (their dark runs' middles along rows 738 to 740 and 753 to 755: 781.9, 907.4, 1033.7, 1160.9, 1288.6 px) on Magpul's 40 mm pitch and the side face's plane (handguard_width), fitted with the camera: the foremost's centre 16.321, one sigma 0.011. The foremost slot itself (608 to 708 px, partly hidden, its middle 658 px) reads 16.287 through the camera; batch 10's yaw correction made it 16.544., harvested
The lower row's foremost slot's centre ahead of the takedown pin15.5 in ± 0.03 in 393.7 mmProvisionalWorked out: Read on 054c636f9e79 through the camera fitted to it (the header): the five see-through slots' middles along row 790 (730.5, 854, 977, 1102.5, 1227.5 px) are where the near and the far chamfers' slots overlap, the far one 16.5 to 2.8 px off the near one toward the lens's foot; with half that taken off, the near slots' centres are 15.499, 13.935, 12.379, 10.794, 9.217 (1.571 apart on average, Magpul's 1.575), the foremost 0.03 behind midway between the upper row's two foremost (16.321 - 0.7875). Batch 10 corrected the middles alone for its yaw: 15.607, the pitch 1.1% long.
Worked out 15.5 in ± 0.03 in used
Read on 054c636f9e79 through the camera fitted to it (the header): the five see-through slots' middles along row 790 (730.5, 854, 977, 1102.5, 1227.5 px) are where the near and the far chamfers' slots overlap, the far one 16.5 to 2.8 px off the near one toward the lens's foot; with half that taken off, the near slots' centres are 15.499, 13.935, 12.379, 10.794, 9.217 (1.571 apart on average, Magpul's 1.575), the foremost 0.03 behind midway between the upper row's two foremost (16.321 - 0.7875). Batch 10 corrected the middles alone for its yaw: 15.607, the pitch 1.1% long., harvested
The upper row's centre line above the pin line1.005 in ± 0.02 in 25.5 mmProvisionalPhoto: a photo on file
Photo 1.005 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the upper row's slots between rows 735 and 757 px on a 3x crop: centre 746 px
The lower row's centre line above the pin line, as it shows from the side0.506 in ± 0.02 in 12.9 mmProvisionalPhoto: a photo on file
Photo 0.506 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the see-through slots between rows 780 and 792 px: centre 786 px
The seated magazine's rear end ahead of the takedown pin (where the upper holds it)4.07 in ± 0.02 in 103.4 mmProvisionalWorked out: Read on a copy on file through the camera fitted to it (the header; 2026-10-19 (night), a working script): the round end's outline against the white above the latch, 1635.3 to 1635.4 px along rows 646 to 654, as the half circle in plan it is (fn-p90-50-magazine.width), the line of sight tangent to it near its rearmost point: 4.070 to 4.071.
Photo 4.1 in ± 0.03 in
the magazine in, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the magazine's feed housing's rear face on a 3x crop, 1635 px, against the rail block's front face
Worked out 4.065 in ± 0.02 in
Read on 054c636f9e79 through the camera fitted to it (the header): the round rear end's outline at 1636 px (row 668) as the half circle in plan it is, as wide as the magazine (fn-p90-50-magazine.width), the line of sight tangent to it 0.25 in nearer the lens than its rearmost point. The rail block's face at 1640.5 px reads 4.043 through the same camera (its far corner, 3.971: rail_block_front_x)., harvested
Worked out 4.07 in ± 0.02 in used
Read on a copy on file through the camera fitted to it (the header; 2026-10-19 (night), a working script): the round end's outline against the white above the latch, 1635.3 to 1635.4 px along rows 646 to 654, as the half circle in plan it is (fn-p90-50-magazine.width), the line of sight tangent to it near its rearmost point: 4.070 to 4.071., harvested
The round end read as the round end it is, through the photo's camera, against the white above the latch; row 668 (camera) is at the latch's height, the latch's dark lobe beside it; the pin frame's 4.10 is the outline's pixel as if the end were flat across at the pins' depth. The 12 in's photo, through its own camera, has 4.082 for the same seat.
The magazine's latch, out of the rear rail block's front face into the notch in the magazine's round end: its underside above the pin line1.78 in ± 0.02 in 45.2 mmProvisionalWorked out: Read on a copy on file through the camera fitted to it (the header; 2026-10-19 (night)): the dark lobe between the magazine's round end and the block's face, white above it to row 657.5 and below it from row 684.5 (between 1636 and 1640 px): its foot at 1.782 on the centre plane. The 12 in's photo has it from 1.76 to 2.10.
Worked out 1.78 in ± 0.02 in used
Read on a copy on file through the camera fitted to it (the header; 2026-10-19 (night)): the dark lobe between the magazine's round end and the block's face, white above it to row 657.5 and below it from row 684.5 (between 1636 and 1640 px): its foot at 1.782 on the centre plane. The 12 in's photo has it from 1.76 to 2.10., harvested
The magazine's latch: its top above the pin line2.12 in ± 0.02 in 53.8 mmProvisionalWorked out: Read on a copy on file as latch_bottom_y: its top at row 657.5, 2.123.
Worked out 2.12 in ± 0.02 in used
Read on a copy on file as latch_bottom_y: its top at row 657.5, 2.123., harvested
The magazine's latch: across0.62 in ± 0.1 in 15.7 mmProvisionalWorked out: {.riser_width}
Worked out 0.62 in ± 0.1 in used
{.riser_width}, harvested
The seated magazine's underside (its body's flat bottom, lying on the handguard's top) above the pin line1.6 in ± 0.01 in 40.6 mmCorroboratedPhoto: a photo on file
Photo 1.572 in ± 0.02 in
the magazine in, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the magazine's lower edge where light shows under it at its front (700 to 701 px, x 780 to 877 px) and along its body on a 3x crop of its rear (700 px); its feed boss hangs below it into the receiver's pocket to 742 px (1.055)
Photo 1.6 in ± 0.01 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by luminance down columns 830, 845 and 860 px (each the median of five), where light shows under the magazine's front end: its lit lower edge (71 to 82) gives way to the light (169 to 189) at 698.5 px; down columns 1040 to 1300 px, where it lies on the handguard, the chamfer's dark band begins under it at 699 px: 1.594 to 1.600 (detail pass, 2026-10-18; the magazine's owner read the same row)
Read down columns where light shows under it, the edge sharp; batch 10's 700 to 701 px is two pixels under it, inside the dark band the chamfer makes under the magazine.
The receiver's round pocket the magazine's feed boss sits in: its centre ahead of the takedown pin5.045 in ± 0.04 in 128.1 mmProvisionalWorked out: {.mag_rear_x} + {fn-p90-50-magazine.width} / 2
Photo 5.09 in ± 0.04 in
the magazine in, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the boss's ends where it shows through the notch in the near wall, 1496 and 1618 px on a 3x crop: the middle
Worked out 5.045 in ± 0.04 in used
{.mag_rear_x} + {fn-p90-50-magazine.width} / 2, harvested
Where the magazine's tower stands: concentric with its round end (US 4,905,394's FIG. 3 and FIG. 4; the magazine's own side photo has the tower flush with its rear end within a pixel), the round end against the rail block. No view on file shows the pocket from above.
The pocket holds the magazine's tower, so it is drawn round it. The notch the tower shows through in the near wall reads 5.09 in the pin frame and 5.111 through the photo's camera (photo): a chord whose two ends lie at two depths of a wall seen from a lens off to one side, ahead of the tower's place by 0.05 to 0.07; both are kept, and the magazine's own photo (the tower concentric with the round end) decides it.
The notch in each wall the magazine's feed tower shows through: its length1.52 in ± 0.05 in 38.6 mmProvisionalPhoto: the magazine in
Photo 1.52 in ± 0.05 in used
the magazine in, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the round piece's ends where it shows through the near wall, 1496 and 1618 px on a 3x crop, the wall dark either side of it
The notch's, not the tower's: the walls cover the tower's ends (the magazine's ledger reads it 1.88 across on photos of it alone).
The round pocket in the receiver's top the magazine's feed tower sits in: its diameter1.883 in ± 0.08 in 47.8 mmProvisionalWorked out: {fn-p90-50-magazine.tower_d} + 2 * {.lug_clearance}
Worked out 1.883 in ± 0.08 in used
{fn-p90-50-magazine.tower_d} + 2 * {.lug_clearance}, harvested
What the pocket holds, a clearance round it: the magazine's own figure (each part its own half of the seat: the tower is the magazine's, the pocket this upper's). No view shows the pocket from above with a scale; the notch it makes in each wall is read (feed_notch_length).
The pocket's floor (the boss's underside) above the pin line1.055 in ± 0.02 in 26.8 mmProvisionalPhoto: the magazine in
Photo 1.055 in ± 0.02 in used
the magazine in, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the boss's lower edge on a 3x crop, 742 px
The handguard's width across its side faces (the receiver's too: one figure)1.44 in ± 0.06 in 36.6 mmProvisionalWorked out: Read through cameras fitted to two three-quarter views: the side face is the plane the M-LOK slots' rims lie on, its distance from the centre plane what the fit leaves free, the rails standing on the centre plane. The 12 in's from ahead, right and above (46e53e61437f, the same section): the front block's 3-slot rail (its slots' edges and its head's flat and bevel, MIL-STD-1913), the side face's three upper M-LOK slots (their rims' outlines on Magpul's 40 mm pitch, their size left free) and the side face's lower edge (the bottom of the outline, where the lower chamfer is seen edge on), with the heights the 16 in's straight view reads: 1.42 (1.44 with the brake as well, its own size free); the slots alone 1.34. The 16 in's from behind, left and above (0bde48a31171): its receiver rail (its teeth's edges, MIL-STD-1913), the left plate's three screws on the receiver's side (plate_screw_*, read near the pins) and four M-LOK slots: 1.42 to 1.47 as the rail's slots are registered, 1.33 to 1.42 on the rims' outlines. One sigma of each fit 0.02 to 0.03; the ± is what the feature sets and the slot outlines move it. The check on a figure no fit took: the slots' size, left free, comes out 33.4 x 6.9 mm and 31.7 x 7.4 mm (Magpul: 32 x 7, approximate); with the pitch left free instead, 39.9 to 40.2 mm. The slots' outlines are their rims: whatever isn't the face's grey (an outline of only the dark and the backdrop follows what shows through a slot, the slots under it and across, and read the 12 in's 0.03 to 0.08 wider: the user, watching the fit). b894132847e8 fixes no width: one row of slots and a barrel of a free radius.
Worked out 1.5 in ± 0.15 in
An assumption for the drawing, not a reading: no view on file is square to the part's end. The feed boss (1.52 across, feed_pocket_d) shows through a notch in the near wall, so the wall stands about as far out as the boss's edge; the three-quarter views (0bde48a31171, b894132847e8) have the side faces standing well outside the rails' standard 0.835 and about as wide as the magazine., harvested
Worked out 1.44 in ± 0.06 in used
Read through cameras fitted to two three-quarter views: the side face is the plane the M-LOK slots' rims lie on, its distance from the centre plane what the fit leaves free, the rails standing on the centre plane. The 12 in's from ahead, right and above (46e53e61437f, the same section): the front block's 3-slot rail (its slots' edges and its head's flat and bevel, MIL-STD-1913), the side face's three upper M-LOK slots (their rims' outlines on Magpul's 40 mm pitch, their size left free) and the side face's lower edge (the bottom of the outline, where the lower chamfer is seen edge on), with the heights the 16 in's straight view reads: 1.42 (1.44 with the brake as well, its own size free); the slots alone 1.34. The 16 in's from behind, left and above (0bde48a31171): its receiver rail (its teeth's edges, MIL-STD-1913), the left plate's three screws on the receiver's side (plate_screw_*, read near the pins) and four M-LOK slots: 1.42 to 1.47 as the rail's slots are registered, 1.33 to 1.42 on the rims' outlines. One sigma of each fit 0.02 to 0.03; the ± is what the feature sets and the slot outlines move it. The check on a figure no fit took: the slots' size, left free, comes out 33.4 x 6.9 mm and 31.7 x 7.4 mm (Magpul: 32 x 7, approximate); with the pitch left free instead, 39.9 to 40.2 mm. The slots' outlines are their rims: whatever isn't the face's grey (an outline of only the dark and the backdrop follows what shows through a slot, the slots under it and across, and read the 12 in's 0.03 to 0.08 wider: the user, watching the fit). b894132847e8 fixes no width: one row of slots and a barrel of a free radius., harvested
A reading over an assumption: two views of the two uppers through cameras on standard features. The assumption's 1.5 is inside its own ± and at the edge of the reading's; it stays beside it.
The receiver's width1.44 in ± 0.06 in 36.6 mmProvisionalWorked out: {.handguard_width}
Worked out 1.44 in ± 0.06 in used
{.handguard_width}, harvested
Drawn as the handguard's: the side face runs on from the handguard across the receiver in Primary Arms' left view, the handguard's rear edge a curve on it; the plate's screws on the receiver's side and the slots on the handguard's lie on one plane in 0bde48a31171's fit.
The handguard's rear edge on the receiver's side (the seam), at its middle6.88 in ± 0.05 in 174.8 mmProvisionalPhoto: a photo on file
Photo 6.88 in ± 0.05 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by on a 3x crop the handguard's rear edge is a curve on the side face from 6.51 at the tray's height (1443 px, row 710) to 7.26 at its foot (1383 px, row 800): its middle, 1413 px
The seam at the tray's height6.51 in ± 0.04 in 165.4 mmProvisionalPhoto: a photo on file
Photo 6.51 in ± 0.04 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the curve's upper end on a 3x crop, 1443 px at row 710
The seam at the side face's foot7.26 in ± 0.04 in 184.4 mmProvisionalPhoto: a photo on file
Photo 7.26 in ± 0.04 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the curve's lower end on a 3x crop, 1383 px at row 800
The height the seam's lower end was read at (handguard_rear_bottom_x), low on the handguard's side0.33 in ± 0.02 in 8.4 mmProvisionalPhoto: a photo on file
Photo 0.33 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the line along the handguard's lower part on a 3x crop (800 px), from the seam to the front block
Batch 10 read this as the side face's foot, a line along the handguard's lower part; the detail pass (2026-10-18) read the section's lines down columns of the photo (lower_chamfer_top_y, keel_top_y): the side face ends higher, at 0.665, and the line this was read on is the lower chamfer's foot, 6 px lower (keel_top_y). Kept for what it was read with: the seam's curve ends here (the model's seam runs from handguard_rear_top_x at the tray to handguard_rear_bottom_x at this height).
The handguard's side face's upper edge, where the chamfer up to its top begins (above the pin line)1.3 in ± 0.015 in 33 mmProvisionalPhoto: a photo on file
Photo 1.3 in ± 0.015 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by luminance down columns 1040, 1170, 1290 and 1300 px: under the magazine's underside (699 px) a dark band, the chamfer facing up into the magazine's black underside, to 722.5 to 723 px, where the side face's grey (67) begins: 1.294 to 1.300
From the side the chamfer shows its height; how far it runs across is the riser's width's (riser_width): the top flat is drawn as wide as the riser standing on it at the front block.
The handguard's section is a top flat, a chamfer down each side to a flat side face, a chamfer under that, and a keel: seen square from ahead in neither photo, but its lines are read down columns of this one, and the views from ahead (b894132847e8; the 12 in's 46e53e61437f, its front ring) show the faces: the front block's riser runs straight down into the upper chamfer, the lower block's sides with their holes into the lower one, and the lower row of M-LOK slots on the lower chamfer (foreshortened from above where the upper row isn't).
The receiver's chamfer along its upper sides, under the rail block: its upper edge, where the receiver's side rises set in to the riser's foot (above the pin line)1.525 in ± 0.012 in 38.7 mmProvisionalPhoto: a photo on file
Photo 1.525 in ± 0.012 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by luminance down columns 1800, 1880 and 1940 px (x 2.06, 1.06, 0.31): the face's grey (52 to 56) above, the band's darker grey (38 to 48) from 704.5 to 705 px down to 723.5 px, where the side face's (52 to 60) begins again: its top 1.519 to 1.525, its foot 1.288 (side_face_top_y's line on the handguard reads 1.294 to 1.300: one line, the receiver's band and the handguard's chamfer meeting the side face on it)
Detail pass, 2026-10-18: a band along the receiver's upper side from its rear face to a ramp under the rail block's window (receiver_chamfer_front_*), dark in the straight view as the handguard's chamfer is, lit from above in 0bde48a31171 and fe9d442f7b56 (a face turned up). Drawn as the handguard's chamfer's plane carried back to this height, the side above it set in to the deck at the riser's foot.
That chamfer's front end, where it meets the face ahead of it, at receiver_chamfer_front_top_y (ahead of the takedown pin)3.7 in ± 0.02 in 94 mmProvisionalPhoto: a photo on file
Photo 3.7 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by along row 707 px: the face's grey (61 to 66) ends at 1668.5 px, the band's dark (13 to 28) begins
The height receiver_chamfer_front_top_x is read at1.494 in ± 0.006 in 37.9 mmProvisionalPhoto: a photo on file
Photo 1.494 in ± 0.006 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by row 707 px
That chamfer's front end lower down, at receiver_chamfer_front_low_y (ahead of the takedown pin): the end is a ramp3.5 in ± 0.02 in 88.9 mmProvisionalPhoto: a photo on file
Photo 3.5 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by along row 721 px: the face's grey (51 to 60) ends at 1684.5 px; rows 712 and 717 between (1673.5, 1679.5 px) on the same line: the band's front end leans back going down, a ramp
The height receiver_chamfer_front_low_x is read at1.319 in ± 0.006 in 33.5 mmProvisionalPhoto: a photo on file
Photo 1.319 in ± 0.006 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by row 721 px
The handguard's side face's lower edge, where the chamfer under it begins (above the pin line)0.665 in ± 0.02 in 16.9 mmProvisionalPhoto: a photo on file
Photo 0.665 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by luminance down columns 1040, 1170 and 1290 px: a step from 61-68 to 68-76 at 773 to 773.5 px, the side face above, the lower chamfer (another tone) below it, with the lower row of M-LOK slots in it (see-through at 780 to 792 px)
The lower chamfer's foot, where a short flat side (the keel, the lower block's width) runs down to the underside (above the pin line)0.259 in ± 0.015 in 6.6 mmProvisionalPhoto: a photo on file
Photo 0.259 in ± 0.015 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by luminance down columns 1040, 1170, 1290 and 1300 px: a dark line (50 to 54) at 805 to 807 px, the keel's face (62 to 70) under it to the underside at 819 px
The line batch 10 read at 800 px (side_face_bottom_y).
How far the lower chamfer runs in, across, from the side face to the keel0.385 in ± 0.05 in 9.8 mmProvisionalWorked out: {.handguard_width} / 2 - {.keel_width} / 2
Worked out 0.385 in ± 0.05 in used
{.handguard_width} / 2 - {.keel_width} / 2, harvested
The keel's width read (keel_width), 2026-10-19 (night); it had been taken to be the riser's.
How far the lower chamfer drops, from the side face's foot to the keel0.406 in ± 0.03 in 10.3 mmProvisionalWorked out: {.lower_chamfer_top_y} - {.keel_top_y}
Worked out 0.406 in ± 0.03 in used
{.lower_chamfer_top_y} - {.keel_top_y}, harvested
The lower chamfers' faces: where their normal points, about +x from the top (90 is the right side)133.5° ± 4°ProvisionalWorked out: 90 degrees + atan(lower_chamfer_run / lower_chamfer_drop) = 90 + atan(0.385 / 0.406): the chamfer's normal, from the read heights, the read width and the read keel; the ± is the run's.
Worked out 133.48 deg ± 4 deg used
90 degrees + atan(lower_chamfer_run / lower_chamfer_drop) = 90 + atan(0.385 / 0.406): the chamfer's normal, from the read heights, the read width and the read keel; the ± is the run's., harvested
The expressions have no arctangent: the value is written as worked out, 90 + atan(lower_chamfer_run / lower_chamfer_drop), and the part's test holds it to its inputs.
The lower row's slots' centres on the lower chamfer: how far out of the centre plane0.569 in ± 0.04 in 14.5 mmProvisionalWorked out: {.handguard_width} / 2 - ({.lower_chamfer_top_y} - {.mlok_lower_y}) * {.lower_chamfer_run} / {.lower_chamfer_drop}
Worked out 0.5692 in ± 0.04 in used
{.handguard_width} / 2 - ({.lower_chamfer_top_y} - {.mlok_lower_y}) * {.lower_chamfer_run} / {.lower_chamfer_drop}, harvested
The lower row's anchor: on the centre plane where the line square to the lower chamfer through a slot's centre meets it (above the pin line)1.046 in ± 0.06 in 26.6 mmProvisionalWorked out: {.mlok_lower_y} + {.mlok_lower_z} * {.lower_chamfer_run} / {.lower_chamfer_drop}
Worked out 1.0458 in ± 0.06 in used
{.mlok_lower_y} + {.mlok_lower_z} * {.lower_chamfer_run} / {.lower_chamfer_drop}, harvested
The lower chamfer's surface from the lower row's anchor, along its normal0.784 in ± 0.06 in 19.9 mmProvisionalWorked out: {.mlok_lower_z} * sqrt(1 + ({.lower_chamfer_run} / {.lower_chamfer_drop}) * ({.lower_chamfer_run} / {.lower_chamfer_drop}))
Worked out 0.7845 in ± 0.06 in used
{.mlok_lower_z} * sqrt(1 + ({.lower_chamfer_run} / {.lower_chamfer_drop}) * ({.lower_chamfer_run} / {.lower_chamfer_drop})), harvested
The riser under each rail block's rail head (the face the rows of blind holes are in), across0.62 in ± 0.03 in 15.7 mmConflictWorked out: {panzer-ar57-ult-12-upper.riser_width}
Worked out 0.835 in ± 0.05 in
An assumption for the drawing: the riser's flat sides run down from the rail's head in fe9d442f7b56 and 0bde48a31171 with no step, so it is drawn as wide as the head's top (std.picatinny.top_width)., harvested
Worked out 0.62 in ± 0.03 in used
{panzer-ar57-ult-12-upper.riser_width}, harvested
A reading over an assumption: the views from behind have the head's overhang against the dark riser, where it doesn't show.
assumed and twelve differ by 0.215 in beyond what each states it is good to.
The keel under the lower chamfers (the lower block's side, the face its row of blind holes is in), across0.67 in ± 0.03 in 17 mmProvisionalWorked out: {panzer-ar57-ult-12-upper.keel_width}
Worked out 0.67 in ± 0.03 in used
{panzer-ar57-ult-12-upper.keel_width}, harvested
The handguard's top flat under the magazine (between the two upper chamfers), across0.835 in ± 0.1 in 21.2 mmProvisionalWorked out: {panzer-ar57-ult-12-upper.top_flat_width}
Worked out 0.835 in ± 0.1 in used
{panzer-ar57-ult-12-upper.top_flat_width}, harvested
The handguard's bore (round the barrel)0.82 in ± 0.1 in 20.8 mmProvisionalWorked out: An assumption for the drawing: from ahead (b894132847e8) the barrel stands in a round opening with a margin about half its own radius; drawn so, and closed above by the tray.
Worked out 0.82 in ± 0.1 in used
An assumption for the drawing: from ahead (b894132847e8) the barrel stands in a round opening with a margin about half its own radius; drawn so, and closed above by the tray., harvested
The barrel's breech end ahead of the takedown pin (hidden in the receiver)5.508 in ± 0.5 in 139.9 mmProvisionalWorked out: {.muzzle_end_x} - {.barrel_with_brake_length}
Worked out 5.508 in ± 0.5 in used
{.muzzle_end_x} - {.barrel_with_brake_length}, harvested
The sellers' barrel with its brake on (18) back from the brake's front: where the drawn barrel starts. How the 18 is counted isn't said: hence the ±.
The row of cross holes along the rear rail block's side, under its slots: their centres above the pin line2.26 in ± 0.015 in 57.4 mmProvisionalPhoto: a photo on file
Photo 2.26 in ± 0.015 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by on a 5x crop (window.png) the holes' centres at 645 px
Those holes' diameter0.125 in ± 0.02 in 3.2 mmProvisionalPhoto: a photo on file
Photo 0.125 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by on a 5x crop the holes are 10 px across
One under each slot (their centres 31.75 px apart on the crop, between the teeth): drawn under each of the 13.
The row of five holes along the front block's top, under its rail: their centres above the pin line2.22 in ± 0.02 in 56.4 mmProvisionalPhoto: a photo on file
Photo 2.22 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by on a 3x crop (front_side.png) the five holes at 648 px
The front block's five holes: the rearmost's centre ahead of the takedown pin15.19 in ± 0.04 in 385.8 mmProvisionalWorked out: Read on a 3x crop of 054c636f9e79 (the five holes at 753, 732, 710, 690 and 668 px: the rearmost 15.113 in the pin frame) through the camera fitted to it (the header), on the face they are in: 15.188, the foremost 16.262.
Worked out 15.19 in ± 0.04 in used
Read on a 3x crop of 054c636f9e79 (the five holes at 753, 732, 710, 690 and 668 px: the rearmost 15.113 in the pin frame) through the camera fitted to it (the header), on the face they are in: 15.188, the foremost 16.262., harvested
The front block's holes, centre to centre0.269 in ± 0.015 in 6.8 mmProvisionalWorked out: Read on the same crop through the camera: the rearmost and the foremost 1.074 apart, four pitches (batch 10: 77 px/in by its yaw correction, and 0.276).
Worked out 0.269 in ± 0.015 in used
Read on the same crop through the camera: the rearmost and the foremost 1.074 apart, four pitches (batch 10: 77 px/in by its yaw correction, and 0.276)., harvested
The row of five holes along the lower rail's block: their centres above the pin line0.186 in ± 0.02 in 4.7 mmProvisionalPhoto: a photo on file
Photo 0.186 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by on a 3x crop (front_side.png) the five holes at 811.7 px
The lower block's five holes: the rearmost's centre ahead of the takedown pin15.33 in ± 0.05 in 389.4 mmProvisionalWorked out: Read on a 3x crop of 054c636f9e79 (the five holes at 738, 713, 688, 663 and 640 px: the rearmost 15.30 in the pin frame) through the camera fitted to it (the header), on the keel's side (0.42 in out): 15.329, the foremost 16.560.
Worked out 15.33 in ± 0.05 in used
Read on a 3x crop of 054c636f9e79 (the five holes at 738, 713, 688, 663 and 640 px: the rearmost 15.30 in the pin frame) through the camera fitted to it (the header), on the keel's side (0.42 in out): 15.329, the foremost 16.560., harvested
The lower block's holes, centre to centre0.308 in ± 0.015 in 7.8 mmProvisionalWorked out: Read on the same crop through the camera: the rearmost and the foremost 1.231 apart, four pitches (batch 10: 77.2 px/in, and 0.317).
Worked out 0.308 in ± 0.015 in used
Read on the same crop through the camera: the rearmost and the foremost 1.231 apart, four pitches (batch 10: 77.2 px/in, and 0.317)., harvested
The bolt's round rear end, as it shows in the receiver's rear face0.75 in ± 0.1 in 19 mmProvisionalWorked out: An assumption for the drawing: from behind and to the left (0bde48a31171) the bolt's end, marked UP, is a disc a little more than half the receiver's rear face across; Small Arms Review's photo of the bolt (1d3f4024e9c6) has it a plain round bar. No view is square to it.
Worked out 0.75 in ± 0.1 in used
An assumption for the drawing: from behind and to the left (0bde48a31171) the bolt's end, marked UP, is a disc a little more than half the receiver's rear face across; Small Arms Review's photo of the bolt (1d3f4024e9c6) has it a plain round bar. No view is square to it., harvested
How far the bolt's end stands out of the rear face0.05 in ± 0.03 in 1.3 mmProvisionalWorked out: An assumption for the drawing: it stands a little proud in 0bde48a31171; no view gives it in profile.
Worked out 0.05 in ± 0.03 in used
An assumption for the drawing: it stands a little proud in 0bde48a31171; no view gives it in profile., harvested
The magazine catch's lever in the rail block's window: its rear face2.93 in ± 0.02 in 74.4 mmProvisionalPhoto: a photo on file
Photo 2.93 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the lever's outline in the window on a 5x crop (window.png), 1730 px
The lever's front face3.16 in ± 0.02 in 80.3 mmProvisionalPhoto: a photo on file
Photo 3.16 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the same crop, 1712 px
The lever's lower end above the pin line1.77 in ± 0.02 in 45 mmProvisionalPhoto: a photo on file
Photo 1.77 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the same crop, 685 px
The lever's upper end above the pin line2.14 in ± 0.02 in 54.4 mmProvisionalPhoto: a photo on file
Photo 2.14 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the same crop, 655 px
How far the lever stands out of the rail block's right side0.3 in ± 0.1 in 7.6 mmProvisionalWorked out: An assumption for the drawing, not a reading: from ahead and to the right (b894132847e8) the lever stands out of the window on the right about a third of the rail's width; no view gives it square.
Worked out 0.3 in ± 0.1 in used
An assumption for the drawing, not a reading: from ahead and to the right (b894132847e8) the lever stands out of the window on the right about a third of the rail's width; no view gives it square., harvested
How deep the blind holes along the rail block and the front block go0.1 in ± 0.05 in 2.5 mmProvisionalWorked out: An assumption for the drawing: they are dark, not lit through, in every view (the window beside them is); no view gives their depth.
Worked out 0.1 in ± 0.05 in used
An assumption for the drawing: they are dark, not lit through, in every view (the window beside them is); no view gives their depth., harvested
The front block's top rail: its front end (its foremost tooth's face)16.32 in ± 0.04 in 414.5 mmProvisionalWorked out: Read on 054c636f9e79 (the foremost tooth's face along row 630, 662 px: 16.247 in the pin frame) through the camera fitted to it (the header), on the rail's near face: 16.324.
Worked out 16.32 in ± 0.04 in used
Read on 054c636f9e79 (the foremost tooth's face along row 630, 662 px: 16.247 in the pin frame) through the camera fitted to it (the header), on the rail's near face: 16.324., harvested
The bore0.224 in ± 0.003 in 5.7 mmProvisionalWorked out: The cartridge's name: 5.7 mm across (5.7 / 25.4); the bore is drawn as one plain hole at it.
Worked out 0.224 in ± 0.003 in used
The cartridge's name: 5.7 mm across (5.7 / 25.4); the bore is drawn as one plain hole at it., harvested
The brake's bore0.24 in ± 0.03 in 6.1 mmProvisionalWorked out: The slot across its front (brake_slot_width) opens the bore it runs into: drawn as wide as the slot. Not read on its face.
Worked out 0.24 in ± 0.03 in used
The slot across its front (brake_slot_width) opens the bore it runs into: drawn as wide as the slot. Not read on its face., harvested
The groove between the brake's rear band and its ported body: its width0.03 in ± 0.015 in 0.8 mmProvisionalWorked out: An assumption for the drawing: a dark line 2 to 3 px wide on a 2x crop of 054c636f9e79, its depth not shown.
Worked out 0.03 in ± 0.015 in used
An assumption for the drawing: a dark line 2 to 3 px wide on a 2x crop of 054c636f9e79, its depth not shown., harvested
That groove's depth0.02 in ± 0.01 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view gives it in profile.
Worked out 0.02 in ± 0.01 in used
An assumption for the drawing, not a reading: no view gives it in profile., harvested
The charging handle's channel along the receiver's right side: its rear end0.57 in ± 0.05 in 14.5 mmProvisionalPhoto: ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600
Photo 0.57 in ± 0.05 in used
ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600, harvested
Scale: its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees. Read by on a 5x crop the channel's rear end at 72 px
The channel's front end6.83 in ± 0.05 in 173.5 mmProvisionalPhoto: ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600
Photo 6.83 in ± 0.05 in used
ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600, harvested
Scale: its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees. Read by on a 5x crop its front end at 266 px
The channel's lower edge above the pin line0.46 in ± 0.04 in 11.7 mmProvisionalPhoto: ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600
Photo 0.46 in ± 0.04 in used
ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600, harvested
Scale: its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees. Read by on a 5x crop 327 px
The channel's upper edge above the pin line1 in ± 0.04 in 25.4 mmProvisionalPhoto: ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600
Photo 1 in ± 0.04 in used
ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600, harvested
Scale: its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees. Read by on a 5x crop 310 px
The charging handle's tab in the channel: its rear end5 in ± 0.05 in 127 mmProvisionalPhoto: ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600
Photo 5 in ± 0.05 in used
ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600, harvested
Scale: its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees. Read by on a 5x crop the raised tab from 209 px
The handle's tab: its front end6.74 in ± 0.05 in 171.2 mmProvisionalPhoto: ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600
Photo 6.74 in ± 0.05 in used
ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600, harvested
Scale: its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees. Read by to 263 px
The handle's tab: its lower edge above the pin line0.67 in ± 0.04 in 17 mmProvisionalPhoto: ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600
Photo 0.67 in ± 0.04 in used
ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600, harvested
Scale: its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees. Read by 321 px
The handle's tab: its upper edge above the pin line0.99 in ± 0.04 in 25.1 mmProvisionalPhoto: ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600
Photo 0.99 in ± 0.04 in used
ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600, harvested
Scale: its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees. Read by 311 px
The opening in the channel's floor onto the bolt: its rear end3.03 in ± 0.05 in 77 mmProvisionalPhoto: ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600
Photo 3.03 in ± 0.05 in used
ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600, harvested
Scale: its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees. Read by the dark opening on a 5x crop from 148 px
That opening's front end3.8 in ± 0.05 in 96.5 mmProvisionalPhoto: ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600
Photo 3.8 in ± 0.05 in used
ar-57center.com upper-16-3.jpg, the 16 in's right side, 800 x 600, harvested
Scale: its lug holes (takedown 54.2, 339.9; pivot 251.8, 337.7 px) as std.ar15.pin_spacing: 31.0 px/in, the photo turned 0.64 degrees. Read by to 172 px
The three screws of the plate over the left side's channel: their centres above the pin line0.64 in ± 0.02 in 16.3 mmProvisionalPhoto: a photo on file
Photo 0.64 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by on a 1.5x crop the three heads at 775 px
The plate's rearmost screw0.94 in ± 0.03 in 23.9 mmProvisionalPhoto: a photo on file
Photo 0.94 in ± 0.03 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by 1890 px
The plate's middle screw2.78 in ± 0.03 in 70.6 mmProvisionalPhoto: a photo on file
Photo 2.78 in ± 0.03 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by 1743 px
The plate's front screw6.43 in ± 0.03 in 163.3 mmProvisionalPhoto: a photo on file
Photo 6.43 in ± 0.03 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by 1450 px
The round-topped notch in the left side's plate, over the channel: its rear edge (ahead of the takedown pin)2.97 in ± 0.02 in 75.4 mmProvisionalPhoto: a photo on file
Photo 2.97 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by its edge's dark line along rows 775, 785 and 795 px at 1723, 1726.5 and 1727 px
Detail pass, 2026-10-18: a notch with a round top in the plate's lower edge (054c636f9e79, fe9d442f7b56), lit inside as the face is, with a line across it at the channel's lower edge (0.446 in at column 1707 px; channel_bottom_y reads 0.46 on the right side): the plate cut away to the channel's floor there, over the right side's opening onto the bolt (bolt_window_rear_x).
That notch's front edge3.47 in ± 0.02 in 88.1 mmProvisionalPhoto: a photo on file
Photo 3.47 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by its edge's dark line along rows 775, 785 and 795 px at 1689.5, 1686 and 1687 px
That notch's round top, at its middle (above the pin line)0.777 in ± 0.015 in 19.7 mmProvisionalPhoto: a photo on file
Photo 0.777 in ± 0.015 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by down column 1707 px its edge's dark line at 764.5 px; at 1695 and 1718 px 768 px, a round as wide as the notch
Those screws' heads, across0.21 in ± 0.03 in 5.3 mmProvisionalPhoto: a photo on file
Photo 0.21 in ± 0.03 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by 17 px on the crop
How deep the channel is cut into the side0.1 in ± 0.05 in 2.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the channel's walls show as a thin dark line in both side views; no view gives its depth.
Worked out 0.1 in ± 0.05 in used
An assumption for the drawing, not a reading: the channel's walls show as a thin dark line in both side views; no view gives its depth., harvested
The gap round the handle's bar in its channel, and round the left side's plate0.03 in ± 0.015 in 0.8 mmProvisionalWorked out: An assumption for the drawing, not a reading: a dark line about two pixels wide in 054c636f9e79 and c261b4c5a32d.
Worked out 0.03 in ± 0.015 in used
An assumption for the drawing, not a reading: a dark line about two pixels wide in 054c636f9e79 and c261b4c5a32d., harvested
How far the handle's tab stands out of the receiver's right side0.2 in ± 0.08 in 5.1 mmProvisionalWorked out: An assumption for the drawing, not a reading: from ahead and to the right (b894132847e8) the tab stands out of the side about a third of the rail's width; no view is square to it.
Worked out 0.2 in ± 0.08 in used
An assumption for the drawing, not a reading: from ahead and to the right (b894132847e8) the tab stands out of the side about a third of the rail's width; no view is square to it., harvested
How deep the opening onto the bolt goes into the receiver from the channel's floor0.3 in ± 0.1 in 7.6 mmProvisionalWorked out: An assumption for the drawing, not a reading: it is dark in every view; it opens onto the bolt, which isn't drawn.
Worked out 0.3 in ± 0.1 in used
An assumption for the drawing, not a reading: it is dark in every view; it opens onto the bolt, which isn't drawn., harvested
The handguard's wall0.12 in ± 0.04 in 3 mmProvisionalWorked out: An assumption for the drawing, not a reading: the M-LOK slots' see-through edges in 054c636f9e79 and the open front end in b894132847e8 show a thin wall, whose thickness no view on file gives in profile.
Worked out 0.12 in ± 0.04 in used
An assumption for the drawing, not a reading: the M-LOK slots' see-through edges in 054c636f9e79 and the open front end in b894132847e8 show a thin wall, whose thickness no view on file gives in profile., harvested
Each lug's clearance to the lower's slot it stands in, per side0.005 in ± 0.005 in 0.1 mmProvisionalWorked out: An assumption for the drawing: the lugs are drawn a few thousandths narrower than the lower's slots (std.ar15.rear_lug_slot_width, front_lug_slot_width) so the two models don't share space; no view gives the lugs' width.
Worked out 0.005 in ± 0.005 in used
An assumption for the drawing: the lugs are drawn a few thousandths narrower than the lower's slots (std.ar15.rear_lug_slot_width, front_lug_slot_width) so the two models don't share space; no view gives the lugs' width., harvested
The rear rail block's window for the handle (the larger, foremost of two): its rear end2.922 in ± 0.02 in 74.2 mmProvisionalPhoto: a photo on file
Photo 2.922 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the window's rear edge on a 5x crop, 1731 px; the lever stands in its rear half
The handle's window: its front end3.546 in ± 0.02 in 90.1 mmProvisionalPhoto: a photo on file
Photo 3.546 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the window's front edge on a 5x crop, 1681 px
The second, smaller window behind it: its rear end2.298 in ± 0.02 in 58.4 mmProvisionalPhoto: a photo on file
Photo 2.298 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by its rear edge on a 5x crop, 1781 px
The second window: its front end2.585 in ± 0.02 in 65.7 mmProvisionalPhoto: a photo on file
Photo 2.585 in ± 0.02 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by its front edge on a 5x crop, 1758 px
The two windows' bottom edge above the pin line1.741 in ± 0.015 in 44.2 mmProvisionalPhoto: a photo on file
Photo 1.741 in ± 0.015 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the windows' lower edge on a 5x crop, 687 px: the riser's foot on the receiver's top
The two windows' top edge above the pin line2.127 in ± 0.015 in 54 mmProvisionalPhoto: a photo on file
Photo 2.127 in ± 0.015 in used
a photo on file, harvested
Scale: the lug holes as std.ar15.pin_spacing (80.21 px/in). Read by the windows' upper edge on a 5x crop, 656 px, under the rail's cross holes
The barrel's shoulder ahead of the takedown pin: where a muzzle device seats (its brake's rear face)21.38 in ± 0.05 in 543.1 mmProvisionalWorked out: {.brake_rear_x}
Worked out 21.38 in used
{.brake_rear_x}, harvested
The brake comes on it: the upper occupies the muzzle slot, and this is where its own brake stands.
The handguard's height, from its underside to the top the magazine lies on (the front block's rails apart)1.502 in ± 0.014 in 38.2 mmProvisionalWorked out: {.tray_top_y} - {.handguard_bottom_y}
Worked out 1.502 in used
{.tray_top_y} - {.handguard_bottom_y}, harvested
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
AR-15 receiver pins
- Lower receivers
- Aero Precision M4E1 complete lower, A2 grip and M4 stock, Aero Precision M4E1 Stripped Lower Receiver, Battle Arms Development Workhorse stripped lower, BCM MK2 AR-15 Lower Receiver, Bear Creek Arsenal BC-15 Multi Caliber, Lower Receiver, Black Anodized, Geissele Automatics Super Duty AR-15 Lower Receiver - Stripped Lower, Palmetto State Armory AR-15 "Stealth" Stripped Lower Receiver
Picatinny rail (MIL-STD-1913)
- Red dot mounts
- Aimpoint Duty RDS One-piece TNP Mount, 30 mm, Aimpoint LRP (Lever Release Picatinny) Mount with 39 mm Spacer, for Micro, Aimpoint One-piece Torsion Nut Mount and Spacer, 39 mm, Geissele Super Precision T1 Mount - 1.93" Height, Geissele Super Precision T1 Mount - Absolute Co-Witness, Geissele Super Precision T1 Mount - Lower 1/3 Co-Witness, Holosun 1.63 in lower 1/3 co-witness pedestal mount (HS-MOUNT-AR-RISER-ARO), Midwest Industries MK2 QD T2 Aimpoint Mount, Low, Midwest Industries MK2 QD T2 Aimpoint Mount, Lower 1/3 Cowitness, Midwest Industries MK2 QD T2 Aimpoint Mount, NV 2.26 in Height, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – 1.93″ HEIGHT, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – LOWER 1/3 (39MM HEIGHT), Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.42 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.57 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.93 in, Scalarworks LEAP/02 Aimpoint Micro T-2 quick-detach mount, 2.26 in, SIG Sauer M1913 I-BEAM Mount, 1.41 in absolute co-witness, SIG Sauer See-Through Riser Mount, 1.41 in absolute co-witness, Unity Tactical FAST Micro Mount, 2.26 in optical centerline
- Optics
- Aimpoint Patrol Rifle Optic (PRO) Red Dot Reflex Sight - QRP2 Mount, EOTECH HWS EXPS3 holographic weapon sight, 1-Dot Speed Ring, Holosun HS510C Open Reflex MRS Solar QD Mount
- Lights
- Olight Baldr S BL, Streamlight ProTac Rail Mount HL-X, SureFire Mini Scout Light Pro, SureFire Scout Light Pro Dual Fuel
- Backup sights
- Daniel Defense A1.5 Fixed Rear Sight, Daniel Defense Rail Mounted Fixed Front Sight, Magpul MBUS 3 Sight – Front, Magpul MBUS 3 Sight – Rear, Magpul MBUS Pro Sight – Front, Magpul MBUS Pro Sight – Rear
- Magnifiers
- EOTECH G33 Magnifier, STS Mount, EOTECH G45 Magnifier, STS Mount, Holosun HM3X 3× magnifier with flip mount
- Scope mounts
- Primary Arms Deluxe AR-15 Scope Mount - 30mm, Primary Arms SLx Cantilever 30mm Mount - 1.5", Reptilia AUS™ MOUNT - 30MM DIAMETER - 39MM HEIGHT, Scalarworks LEAP/08 quick-detach scope mount, 30 mm, 1.57 in, SIG SAUER ALPHA-MSR scope mount, 30 mm, Vortex Sport Cantilever 30mm Mount
Muzzle thread
- Muzzle devices
- Dead Air XRF Xeno Rimfire Muzzle Brake, HUXWRX Flash Hider-QD 556 1/2x28, Mil-spec A2 flash hider, 1/2-28 (drawing 9349051), Nordic Components 1/2-28 thread protector (ships on the 22RB), Otter Creek Labs Polonium, Otter Creek Labs Polonium K, Precision Armament M4-72 Severe-Duty® Compensator, SilencerCo Sparrow 22, SureFire ProComp 556 Muzzle Brake, SureFire SOCOM 3-Prong Flash Hider, SureFire SOCOM 4-Prong Flash Hider, SureFire WARCOMP Flash Hider, Taurus TX22 Thread Protector, VG6 Precision GAMMA 556
P90 magazine, on top of the upper
M-LOK
- Hand stops
- BCM KAG (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK Hand Stop (fit unchecked), Magpul M-LOK Index Panel (fit unchecked)
- Vertical grips
- BCM Vertical Grip Mod 3 (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK MVG vertical grip (fit unchecked)
- Lights
- Cloud Defensive REIN (fit unchecked), Streamlight ProTac Rail Mount HL-X (fit unchecked), SureFire Mini Scout Light Pro (fit unchecked), SureFire Scout Light Pro Dual Fuel (fit unchecked)
- Rail sections
- Magpul M-LOK® Aluminum Rail, 3 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 5 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 7 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 9 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 11 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 3 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 5 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 7 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 9 Slots (fit unchecked)
- Adapter plates
- Magpul M-LOK Hand Stop MOE Adapter (fit unchecked)
- Sling mounts
- Magpul M-LOK QD Sling Mount (fit unchecked)
- Rail covers
- Magpul M-LOK Rail Cover Type 2