Light
Cloud Defensive REIN
Cloud Defensive's full-size weapon light: 100,000 candela and 1,250 lumens from one 18650 (or two CR123A), with a remote switch and an inline M-LOK mount in the box. Its page is titled 'Cloud Defensive REIN (Black)'; the maker calls this generation the REIN 3.0 ('The gold standard. The REIN 3.0'). Also sold in FDE and Earth Brown.

- Weight
- 6.91 oz ± 0.005 oz Confirmedpublished: Cloud Defensive, Cloud Defensive REIN (Black), Output & Specs, the maker, read Oct 5, 2026
- Lowest price
- $369.99 at Cloud Defensive, read Nov 21, 2026 (Black)
- Maker's number
- REIN 3.0-DF-S-650 BLK
- Colours
- Black, FDE, Earth Brown, OD Green
- Drawn as
- modelled
- Maker's page
- clouddefensive.com
Added to “22RB .22 LR rifle”, a build on the start page, where the designer starts a new light.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Overall length6.17 in ± 0.005 in 156.7 mmConfirmedPublished: Cloud Defensive, Cloud Defensive REIN (Black), Output & Specs, the maker, read Oct 5, 2026
Published “6.17" Length” used
Cloud Defensive, Cloud Defensive REIN (Black), Output & Specs, the maker, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “The overall length measures 6.17 inches .”
Alexander's, Cloud Defensive REIN 3.0 1250-Lumen M-LOK Weaponlight (MPN REIN 3.0-DF-S-650 BLK), a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
The maker's own page; the seller repeats it.
No page says what the length is measured between; taken as the bezel's front face to the tail cap's rear, the remote switch and its cable left out.
Head (bezel) diameter1.3 in ± 0.05 in 33 mmConfirmedPublished: Cloud Defensive, Cloud Defensive REIN (Black), Output & Specs, the maker, read Oct 5, 2026
Published “1.3" Bezel Diameter” used
Cloud Defensive, Cloud Defensive REIN (Black), Output & Specs, the maker, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “The bezel (head) diameter is 1.30 inches .”
Alexander's, Cloud Defensive REIN 3.0 1250-Lumen M-LOK Weaponlight (MPN REIN 3.0-DF-S-650 BLK), a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “Head Diameter : 1.30"”
Impact Guns, Cloud Defensive REIN 3.0 Weaponlight, Black, M-Lok Mount (850016201928), a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
The maker's own figure; the sellers' second decimal agrees with it.
The maker writes one decimal, two sellers write 1.30. Taken as the head's front section, its largest (the two sections behind it read 0.3% and 0.5% less on the photos).
Body diameter (the plain tube between the banded grip section and the head)0.881 in ± 0.004 in 22.4 mmCorroboratedPhoto: Rifle Supply CLDREIN-3-0-DFS650-BLK_1_HR, the black light standing lens up on white, 2000 x 2000; a quarter turn of f23602b1d23a, pixel for pixel
Photo 0.881 in ± 0.004 in used
Rifle Supply CLDREIN-3-0-DFS650-BLK_1_HR, the black light standing lens up on white, 2000 x 2000; a quarter turn of f23602b1d23a, pixel for pixel, harvested
Scale: the bezel's front section, 394.4 px over columns 1600 to 1840, as head_diameter (1.3 in). Read by the tube's width as a line along the photo, 254.59 + 0.00725 u px over columns 900 to 1030 and 1060 to 1190 (rms 0.29 px), carried to the bezel's columns: the bezel is 1.4757 of it there (sd 0.0026 over 224 columns). ± covers the fit and the second photo, not the bezel's own ±
Photo 0.883 in ± 0.004 in
Rifle Supply CLDREIN-3-0-DFS650-BLK_2_HR, the black light standing tail up on white, 2000 x 2000; a quarter turn of 582744b1629f, pixel for pixel, harvested
Scale: the bezel's front section, 394.6 px over columns 1660 to 1860, as head_diameter (1.3 in). Read by the tube's width as a line along the photo, 278.01 - 0.00568 u px over columns 930 to 1060 and 1090 to 1215 (rms 0.26 px), carried to the bezel's columns: the bezel is 1.4726 of it there (sd 0.0014 over 201 columns)
The photo the outline is traced from; the other, taken from the other end, reads 0.002 in more, inside both ±.
Not published. The tube against the bezel on Rifle Supply's two studio photos of the light standing, one lens up and one tail up: each is taken from above its upper end, so the end nearer the lens reads larger (the tube itself widens 0.8% along its own inch in one and narrows 0.6% in the other). In each the tube's width is fitted as a line along the photo and carried to the bezel's columns (tools/trace.py fit_tube, as its tube calibration does); read that way the two photos agree to 0.2%.
The body's axis above the mounting face (the inline M-LOK mount's underside, which lies on the handguard's face)0.82 in ± 0.03 in 20.8 mmProvisionalPhoto: Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800
Photo 0.82 in ± 0.03 in used
Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800, harvested
Scale: the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787). Read by the tube's axis (row 226.5) to the mount's top edge on the near side (row 289.75): 63.25 px, plus 5.9 px for that edge standing 0.17 in nearer the lens than the axis (the mount's underside shows 21 px of its 0.60 in width: the photo looks up at it from 17.8 degrees), over that angle's cosine: 0.630 in from the axis to the mount's top; plus the mount's thickness by the same photo (mount_thickness, 0.187 in). ± covers a pixel and a half at each edge, 3 degrees of the angle and the thickness's own ±
Not published. On the inline M-LOK mount that is in the box. It leaves the tail cap (0.54 in radius) 0.09 in over the mount's top and the head 0.17 in over the handguard's face.
Overall width (with its mount; the remote switch and its cable left out)1.3 in ± 0.05 in 33 mmConfirmedWorked out: {.head_diameter}
Worked out 1.3 in ± 0.05 in used
{.head_diameter}, harvested
No published figure. The head is the widest thing: the mount is 0.60 in wide and the body sits 0.13 in to one side of its middle, inside the head's width (Impact Guns lists 'Width : 1.30"', its head diameter).
M-LOK slots its mount's lugs span1ProvisionalPhoto: Inside Safariland REIN-LIGHT-INSTALL-2-JASON-MOSHER-1.jpg: the mount and the light's centre section on a handguard's upper right M-LOK row, tail cap off, 800 x 800
Photo 1 count used
Inside Safariland REIN-LIGHT-INSTALL-2-JASON-MOSHER-1.jpg: the mount and the light's centre section on a handguard's upper right M-LOK row, tail cap off, 800 x 800, harvested
Scale: the handguard's own M-LOK slots in the mount's row (the slot behind the mount is 120 px long: std.mlok.slot_length). Read by the mount's two T-nut screws (columns 291 and 362) both stand over the slot that begins one web ahead of the slot behind (columns 270 to 392), centred on it; the bar ahead of them carries the light and has no nut
No sheet states it. The inline mount has two T-nut screws an M-LOK interval apart at its rear end, and both go into one slot.
Distance between the mount's two T-nut screws (centre to centre)0.787 in ± 0.004 in 20 mmConfirmedWorked out: {std.mlok.interval}
Worked out 0.7874 in ± 0.004 in used
{std.mlok.interval}, harvested
Photo 0.773 in ± 0.025 in
Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800, harvested
Scale: the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787). Read by the two T-nuts' screw shanks under the mount, 89 px apart (columns 555 and 644 of the levelled photo)
Photo 0.795 in ± 0.03 in
Inside Safariland REIN-LIGHT-INSTALL-2-JASON-MOSHER-1.jpg: the mount and the light's centre section on a handguard's upper right M-LOK row, tail cap off, 800 x 800, harvested
Scale: the slot behind the mount, 120 px long (std.mlok.slot_length, 32 mm: 3.75 px/mm), less 6% for the top rail's tooth pitch falling from that slot to the mount (a close photo): 3.51 px/mm at the screws. Read by the two screw heads' centres, 71 px apart
Two nuts that share one slot stand the standard's interval apart; the two photos read 0.773 and 0.795 in, either side of it and inside their ±.
The M-LOK interval, as two nuts in one slot have to be; both photos read it within their ±.
Reach inside the handguard (below the mounting face, tightened)No value yetMissingNo source yet
Not sourced: no page or sheet gives the T-nuts' height, and the one photo of them shows them hanging loose under the mount.
Rear T-nut screw's centre ahead of the mount's rear end0.3 in ± 0.02 in 7.6 mmCorroboratedPhoto: Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200
Photo 0.3 in ± 0.02 in used
Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200, harvested
Scale: an affine camera fitted to the photo: the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across. Read by the rear pocket's centre to the outline's rear end along the pockets' line: 8.16 mm, less 0.5 mm for the outline there being the bottom edge seen past the top (the bar's thickness at 17 degrees)
Photo 0.295 in ± 0.025 in
Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800, harvested
Scale: the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787). Read by the rear T-nut's screw shank (column 644) to the bar's rear end (column 678.7): 34 px
Read in the plate's own plane on the maker's photo; the side photo agrees within 0.005 in.
Inline mount: overall length3.14 in ± 0.04 in 79.8 mmCorroboratedPhoto: Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200
Photo 3.14 in ± 0.04 in used
Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200, harvested
Scale: an affine camera fitted to the photo: the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across. Read by the outline's two ends along the line through the pockets' centres: 79.75 mm
Photo 3.148 in ± 0.04 in
Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800, harvested
Scale: the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787). Read by the bar's two ends, columns 316 and 678.7 of the levelled photo: 362.7 px
The maker's photo of the mount alone; the side photo, scaled by the light's tube, reads the same within 0.01 in. Two photos and two scales that share nothing.
Not published (the maker states no size for the mount).
Inline mount: width0.6 in ± 0.03 in 15.2 mmProvisionalPhoto: Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200
Photo 0.6 in ± 0.03 in used
Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200, harvested
Scale: an affine camera fitted to the photo: the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across. Read by the top face at the hole end, between the two pairs of holes: 175 px across (15.17 mm). At the T-nut end the top face is 12.5 mm between its bevels
Inline mount: thickness0.187 in ± 0.02 in 4.7 mmCorroboratedPhoto: Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800
Photo 0.187 in ± 0.02 in used
Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800, harvested
Scale: the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787). Read by the bar's near side face between the light's two feet, rows 289.75 to 310.25 at column 415: 20.5 px, over the cosine of the 17.8 degrees the photo looks up at it from
Photo 0.192 in ± 0.03 in
Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200, harvested
Scale: an affine camera fitted to the photo: the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across. Read by the near side wall at the hole end, 17 px high in the photo: the thickness times the sine of the 16.9 degrees the plate is seen from (4.88 mm)
A side face seen nearly square; the plan photo's reading hangs on a small angle's sine and agrees within 0.005 in.
One thickness along its length: on the side photo its top edge is level from end to end, and the T-nut end's upper long edges are bevelled (mount_bevel).
Inline mount: the bevel along the T-nut end's two upper long edges0.08 in ± 0.03 in 2 mmProvisionalPhoto: Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800
Photo 0.08 in ± 0.03 in used
Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800, harvested
Scale: the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787). Read by the dark band along the top of the bar's side face from the rear end to column 503 (rows 291 to 297: 6 px), taken as a 45 degree bevel seen from 17.8 degrees under: its height over (cos - sin) of that angle. The maker's photo shows the T-nut end's top face 12.5 mm wide against 15.2 at the hole end: 1.3 mm a side if the two bevels are alike
Inline mount: how far the bevels run from the rear end1.52 in ± 0.08 in 38.6 mmProvisionalPhoto: Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800
Photo 1.52 in ± 0.08 in used
Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800, harvested
Scale: the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787). Read by the dark band's front end, a slant over columns 497 to 510, to the bar's rear end (column 678.7): 175 px
Inline mount: the rear end's corner radius in plan0.2 in ± 0.05 in 5.1 mmProvisionalPhoto: Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200
Photo 0.2 in ± 0.05 in used
Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200, harvested
Scale: an affine camera fitted to the photo: the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across. Read by the top face's far edge leaves its line 5 mm short of the rear tip, half the plate's width out from the middle: corners of about that radius with a short flat between them
Inline mount: the T-nut screws' pockets (diameter)0.384 in ± 0.015 in 9.8 mmProvisionalPhoto: Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200
Photo 0.384 in ± 0.015 in used
Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200, harvested
Scale: an affine camera fitted to the photo: the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across. Read by the two pockets' rims, ellipses of 58.5 px semi-major axis (unforeshortened): 117 px at 11.99 px/mm
Their depth isn't measured.
Inline mount: the rearmost of its four holes for the light, ahead of the rear T-nut screw1.559 in ± 0.03 in 39.6 mmCorroboratedPhoto: Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200
Photo 1.559 in ± 0.03 in used
Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200, harvested
Scale: an affine camera fitted to the photo: the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across. Read by the far row's rear hole (its opening's centre) 39.30 mm ahead of the rear pocket's centre, plus 0.3 mm for the hole's rim lying lower than the pocket's (the two are read as one plane)
Photo 1.554 in ± 0.03 in
Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800, harvested
Scale: the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787). Read by the rear one of the two screw heads in the mount's underside (column 465) to the rear T-nut's screw (column 644): 179 px
The hole itself on the maker's photo; the screw in it on the side photo is 0.005 in off.
Four holes for the light's two screws, in two rows either side of the T-nuts' line; the maker: 'Two mounting positions allows the user to customize the fit to their setup.' The rear row is the far one in the maker's photo, to the left of the mount's middle looking toward the lens with the mount face down.
Inline mount: spacing of a row's two holes (the light's two screws)0.833 in ± 0.02 in 21.2 mmCorroboratedPhoto: Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200
Photo 0.833 in ± 0.02 in used
Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200, harvested
Scale: an affine camera fitted to the photo: the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across. Read by the two rows read 21.15 and 21.18 mm between their holes' centres
Photo 0.868 in ± 0.035 in
Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800, harvested
Scale: the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787). Read by the two screw heads in the mount's underside, columns 365 and 465: 100 px (seen at a grazing angle)
The holes seen from above; the screw heads on the side photo are within its ±.
Inline mount: how far the second row of holes stands ahead of the first0.169 in ± 0.02 in 4.3 mmProvisionalPhoto: Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200
Photo 0.169 in ± 0.02 in used
Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200, harvested
Scale: an affine camera fitted to the photo: the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across. Read by the near row's holes 4.28 and 4.31 mm ahead of the far row's along the plate
Inline mount: each row of holes from the T-nuts' line0.131 in ± 0.02 in 3.3 mmProvisionalPhoto: Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200
Photo 0.131 in ± 0.02 in used
Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200, harvested
Scale: an affine camera fitted to the photo: the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across. Read by the two rows 6.65 mm apart across the plate (2.9 mm one side of the pockets' line and 3.7 the other, before allowing for the holes' rims lying lower than the pockets'): half of it, the rows taken as alike either side
How far the light's axis sits to one side of the mount's middle: the body's two feet bolt to one row or the other.
Inline mount: its holes for the light's screws (diameter)0.176 in ± 0.02 in 4.5 mmProvisionalPhoto: Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200
Photo 0.176 in ± 0.02 in used
Cloud Defensive Inlinemlok.jpg: the inline mount alone on white, seen from above at an angle, 1200 x 1200, harvested
Scale: an affine camera fitted to the photo: the two screw pockets' rims are ellipses of 58.5 x 56.0 px with their long axes at +13 degrees (the plate is seen 17 degrees off its normal), and the pockets' centres, 238.5 px apart, are taken as the M-LOK interval apart (std.mlok.interval, 20 mm): 11.93 px/mm along the plate, 11.54 across. Read by each hole's opening, 53 px long and 40.8 across, as its rim seen 17 degrees off square with 11 px of its far wall showing: a 54.1 px rim (4.5 mm)
The tail cap's rear face ahead of the mount's rear end0.21 in ± 0.04 in 5.3 mmProvisionalPhoto: Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800
Photo 0.21 in ± 0.04 in used
Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800, harvested
Scale: the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787). Read by the grip section's bands on the photo against the same bands on the traced outline (profiles.side): the front band's two faces are 2.983 and 2.500 in ahead of the mount's rear end and 2.787 and 2.277 in ahead of the tail cap's rear face, the rear band's front face 2.057 and 1.855: 0.196, 0.223 and 0.202 in. ± covers their spread and 1% of the photo's scale over 3 in
Where the light sits along its mount, on the row of holes Safariland's reviewer used (the rear one). The mount's rear end stands out behind the tail cap; the rear T-nut screw is under the tail cap's last 0.1 in.
The light's front mounting foot: its centre ahead of the mount's rear end2.734 in ± 0.03 in 69.4 mmProvisionalPhoto: Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800
Photo 2.734 in ± 0.03 in used
Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800, harvested
Scale: the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787). Read by the front foot's sole, columns 345 to 382.7 of the levelled photo: its middle to the bar's rear end (column 678.7)
The body has two feet under its grip section (Cloud Defensive: 'the standard SCOUT mounting profile'), each centred under one of the section's two bands.
The light's two mounting feet: centre to centre0.929 in ± 0.025 in 23.6 mmProvisionalPhoto: Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800
Photo 0.929 in ± 0.025 in used
Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800, harvested
Scale: the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787). Read by the two soles' middles, columns 363.8 and 470.8: 107 px. The screws that hold them are 0.833 in apart (mount_hole_spacing), each a little inboard of its foot's middle
The light's mounting feet: length of a sole along the body0.325 in ± 0.02 in 8.3 mmProvisionalPhoto: Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800
Photo 0.325 in ± 0.02 in used
Inside Safariland REIN-LIGHT-MOUNTING-BRACKET-JASON-MOSHER-1.jpg: the light's centre section bolted to the inline mount, lying on a dark surface, seen from the side and from 18 degrees under the mount's face, 800 x 800, harvested
Scale: the plain tube's silhouette, 101.5 px across (rows 176 to 277.5 with the photo turned 8.1 degrees to level the body), as body_diameter (0.881 in): 115.2 px/in; the two T-nut screws read 0.77 in apart at that scale (the M-LOK interval is 0.787). Read by the two soles, 37.7 and 37 px long; each foot widens upward to its band's length where it joins the body
How wide a foot is across the body isn't measured: no photo on file shows the feet square from an end.
The bezel's clear opening (the lens as it shows)0.99 in ± 0.04 in 25.1 mmProvisionalPhoto: Rifle Supply CLDREIN-3-0-DFS650-BLK_3_HR: the black light lying on white, three-quarter view from the lens end, 2000 x 2000
Photo 0.99 in ± 0.04 in used
Rifle Supply CLDREIN-3-0-DFS650-BLK_3_HR: the black light lying on white, three-quarter view from the lens end, 2000 x 2000, harvested
Scale: the bezel's own silhouette just behind the lens, 450 px across the light's axis, as head_diameter (1.3 in). Read by the bright opening inside the bezel's rim as an ellipse: 343.8 px along its long axis, which lies square to the light's axis: 0.764 of the bezel
The tail cap's rubber button (diameter, on the rear face)0.73 in ± 0.05 in 18.5 mmProvisionalPhoto: Cloud Defensive ReinCoyotebrown2.jpg, the Earth Brown page: the light from behind, three-quarter view, 1600 x 1600
Photo 0.73 in ± 0.05 in used
Cloud Defensive ReinCoyotebrown2.jpg, the Earth Brown page: the light from behind, three-quarter view, 1600 x 1600, harvested
Scale: the tail cap itself along the same line, 225 px, as its diameter on the traced outline (1.07 in). Read by the grey button as an ellipse, 153 px along its long axis (which lies square to the light's axis): 0.68 of the tail cap
The push button in the tail cap's rear face, flush in its rim; grey rubber on every colour of light.
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
M-LOK
- Uppers
- Nordic Components 22RB .22 LR upper, 16" (fit unchecked), Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12" (fit unchecked), Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16" (fit unchecked)
- Handguards
- Aero Precision AR15 10.3" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 12.7" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 15" Enhanced M-LOK Handguard, Gen 2 (fit unchecked), Aero Precision AR15 15" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 15" S-ONE M-LOK Handguard (fit unchecked), Aero Precision AR15 16.6" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 7.3" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 9.3" R-ONE M-LOK handguard (fit unchecked), BCM MCMR-10 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM MCMR-13 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM MCMR-15 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM PMCR (Polymer M-LOK® Compatible Rail)* Carbine Length-BLACK (fit unchecked), BCM PMCR (Polymer M-LOK® Compatible Rail)* Mid Length-BLACK (fit unchecked), Expo Arms Free Float AR-15 Handguard - M-LOK - 15" (fit unchecked), Geissele Automatics 10.5" Super Modular Rail MK16 M-LOK (fit unchecked), Geissele Automatics 13.5" Super Modular Rail MK16 M-LOK (fit unchecked), Geissele Automatics 15" Super Modular Rail MK16 M-LOK (fit unchecked), Magpul MOE SL® Hand Guard, Carbine-Length – AR15/M4 (fit unchecked), Magpul MOE SL® Hand Guard, Mid-Length – AR15/M4 (fit unchecked), Magpul MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4 (fit unchecked), Magpul MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4 (fit unchecked), MAS Defense 12.62" NERO M-LOK FREE FLOAT (fit unchecked), MAS Defense 15" NERO M-LOK FREE FLOAT (fit unchecked), MAS Defense 9.87" NERO M-LOK FREE FLOAT (fit unchecked), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine) (fit unchecked), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length) (fit unchecked), Midwest Industries Combat Rail One Piece Free Float Handguard, M-LOK™ (15") (fit unchecked)
- Adapter plates
- Magpul M-LOK Hand Stop MOE Adapter (fit unchecked)
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Cloud Defensive $369.99 Black Nov 21, 2026, in stock that day
- Cloud Defensive $369.99 FDE Nov 21, 2026, in stock that day
- AR15Discounts $399.99 Black Nov 21, 2026, stock not said
- AR15Discounts $399.99 FDE Nov 21, 2026, stock not said
- KYGUNCO $349.99 Black Nov 21, 2026, out of stock that day
- KYGUNCO $349.99 FDE Nov 21, 2026, out of stock that day
- GRITR Outdoors $349.99 OD Green Nov 21, 2026, out of stock that day
- Cloud Defensive $369.00 Earth Brown Oct 21, 2026, out of stock that day
- Impact Guns $399.99 Black Nov 21, 2026, out of stock that day
- Sportsman's Warehouse $399.99 Black Nov 21, 2026, out of stock that day
- Dirty Bird Industries $399.99 Black Nov 21, 2026, out of stock that day
- Impact Guns $399.99 FDE Nov 21, 2026, out of stock that day
- Sportsman's Warehouse $399.99 FDE Nov 21, 2026, out of stock that day
- Dirty Bird Industries $399.99 FDE Nov 21, 2026, out of stock that day
- Alexander's Store $399.99 Black Nov 18, 2026, out of stock that day
- Rifle Supply $430.99 Black Nov 21, 2026, out of stock that day
- Rifle Supply $430.99 FDE Nov 21, 2026, out of stock that day