Handguard
Magpul MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4
Magpul's polymer drop-in hand guard for a mid-length gas system, in two halves: "Replaces standard AR15/M4 hand guards on mid-length gas systems"; "M-LOK slots at the two, six, and ten o'clock positions"; "The integral, riveted aluminum heat shield, combined with the front lower lip and side extensions, shields the support hand from a hot gas block"; "Relief cut at the top rear of the handguard accommodates overhanging optics"; "Constructed of reinforced, heat-resistant Magpul polymer"; "Made in the USA" (Magpul). It goes on the rifle's own barrel nut and delta ring and the cap behind its front sight base: no free-float nut of its own.

- Weight
- 8.7 oz Confirmedpublished: Magpul, MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4, Model MAG426: Specifications, the maker, read Oct 28, 2026
- Lowest price
- $28.80 at KYGUNCO, read Nov 21, 2026 (Stealth Gray)
- Maker's number
- MAG426
- Colours
- Black, Flat Dark Earth, Olive Drab Green, Stealth Gray
- Drawn as
- modelled
- Maker's page
- magpul.com
In “Drop-in 16 in, Stealth Gray on BCM's MK2 lower”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Length, overall9.2 in 233.7 mmConfirmedPublished: Magpul, MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4, Model MAG426: Specifications, the maker, read Oct 28, 2026
Published “Length, overall: 9.2 in.” used
Magpul, MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4, Model MAG426: Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Published “It measures 9.2" long, 2.5" tall, and 2.2" wide”
Primary Arms, Magpul MOE Drop In AR-15 Handguard - M-LOK - Mid-Length (black, MAG426-BLK), a seller, read Oct 28, 2026 the page, harvested Oct 28, 2026
The maker's figure; Primary Arms' page states the same.
From its rear end, which stands in the delta ring's skirt against the ring's lip, to the tip of its front end, which wraps the front sight base's rear.
Length, mounting (from its rear end in the delta ring to its front flange's end in the cap)8.6 in 218.4 mmConfirmedPublished: Magpul, MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4, Model MAG426: Specifications, the maker, read Oct 28, 2026
Published “Length, mounting: 8.6 in.” used
Magpul, MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4, Model MAG426: Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Magpul says no more than the figure. Taken here as from the rear end that bears on the delta ring's lip to the front end of the front flange, which its instructions slide "into the metal Hand Guard cap, located behind the front sight base": the length a rifle's ring and cap have to hold it between. The overall length runs 0.6 in further, over the cap and the front sight base's rear.
Width2.2 in 55.9 mmConfirmedPublished: Magpul, MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4, Model MAG426: Specifications, the maker, read Oct 28, 2026
Published “Width 2.2 in.” used
Magpul, MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4, Model MAG426: Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Published “It measures 9.2" long, 2.5" tall, and 2.2" wide”
Primary Arms, Magpul MOE Drop In AR-15 Handguard - M-LOK - Mid-Length (black, MAG426-BLK), a seller, read Oct 28, 2026 the page, harvested Oct 28, 2026
The maker's figure; Primary Arms' page states the same.
No view on file looks at it from above or from an end square on, so the width isn't read on a photo: the height Magpul gives reads 6% more than its photo does (height), and its width may say as much more than the part is. Drawn at Magpul's figure.
Height, excluding the front lower lip2.34 in ± 0.04 in 59.4 mmConflictPhoto: Magpul's feature image 03 for MAG426: the OD green hand guard on a rifle with an A2 front sight, the rifle's right side seen level, 700 x 525
Published “Height, excluding lip: 2.5 in.”
Magpul, MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4, Model MAG426: Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Published “It measures 9.2" long, 2.5" tall, and 2.2" wide”
Primary Arms, Magpul MOE Drop In AR-15 Handguard - M-LOK - Mid-Length (black, MAG426-BLK), a seller, read Oct 28, 2026 the page, harvested Oct 28, 2026
Photo 2.34 in ± 0.04 in used
Magpul's feature image 03 for MAG426: the OD green hand guard on a rifle with an A2 front sight, the rifle's right side seen level, 700 x 525, harvested
Scale: its three M-LOK slots: centres 64.29 px apart (two pitches of 128.6 px) for the standard's 40 mm (std.mlok.slot_pitch), 40.82 px/in; their length, 51.9 px, for the standard's 32 mm (std.mlok.slot_length), 41.2 px/in; and the visible length (visible_length) at 40.86 px/in. Read by the body's top (row 151.5) to its bottom (row 247.0) over the length clear of both ends and the lip (columns 165 to 465, the outline at saturation > 0.18): 95.5 px at the visible length's 40.86 px/in; ± 1.5 px. The traced outline's straight runs, each taken at the middle of its pixel stair, give 2.32 (the model's)
Photo 2.38 in ± 0.02 in
Primary Arms' gallery for the black MAG424, its right side seen level, alone on white, 1152 x 768, harvested
Scale: its own three M-LOK slots, 211.3 px apart for the standard's 40 mm (134.2 px/in), which put its overall length at 7.14 for Magpul's 7.1. Read by the body's top to its bottom clear of the lip, 320 px: the carbine-length guard, the same section by every photo of the two
Two photos, each scaled by its own M-LOK slots at the standard's pitch (and the carbine's also by Magpul's overall length, within 0.5%), give 2.34 and 2.38 for the body's height clear of the lip; Magpul's 2.5 is 6% more, and what it measures over isn't said (the lip reaches 2.57 in the same photo). A side view seen from a little above or below would read taller, not shorter. The model is the traced outline, at the photo's height.
magpul and photo differ by 0.16 in beyond what each states it is good to.
magpul and carbine-photo differ by 0.12 in beyond what each states it is good to.
primary-arms and photo differ by 0.16 in beyond what each states it is good to.
primary-arms and carbine-photo differ by 0.12 in beyond what each states it is good to.
Inside diameterNo value yetMissingNo source yet
Magpul gives none: the room inside it isn't published. The model's inside is its outside less the wall (wall), which no view gives either.
Its rear end (bearing on the delta ring's lip) ahead of the receiver's front face0.336 in ± 0.015 in 8.5 mmProvisionalWorked out: {std.ar15.slip_ring_front_x}
Worked out 0.336 in ± 0.015 in used
{std.ar15.slip_ring_front_x}, harvested
Where the standard's delta ring holds it: its rear end in the ring's skirt, against the lip (std.ar15.slip_ring_front_x, from the Army's drawings). Its instructions: "make sure your delta ring is securing BOTH upper and lower rear flanges of the Hand Guards".
Where its body shows ahead of the delta ring (the ring's skirt's front end), from its rear end0.12 in ± 0.005 in 3 mmConfirmedWorked out: {std.ar15.slip_ring_skirt_length}
Worked out 0.12 in ± 0.005 in used
{std.ar15.slip_ring_skirt_length}, harvested
Its rear end stands in the ring's front skirt (std.ar15.slip_ring_skirt_length): the outline traced on the rifle begins where the skirt ends.
Its length seen ahead of the delta ring (to the tip of its front end)9.08 in ± 0.01 in 230.6 mmConfirmedWorked out: {.length} - {.visible_rear_x}
Worked out 9.08 in ± 0.01 in used
{.length} - {.visible_rear_x}, harvested
Photo 9.11 in ± 0.04 in
Magpul's feature image 03 for MAG426: the OD green hand guard on a rifle with an A2 front sight, the rifle's right side seen level, 700 x 525, harvested
Scale: its three M-LOK slots, centres 64.29 px apart for the standard's 40 mm (std.mlok.slot_pitch): 40.82 px/in. Read by the outline at saturation > 0.18 (the delta ring and the front sight left out), from its rear edge at the ring's front (column 140.5) to its front tip (511.5): 371 px; ± 1.5 px
Magpul's overall length less the standard's skirt: the photo, scaled by the standard's M-LOK slots and not by any length of the part, agrees within 0.03 in (0.3%).
Its top above the bore axis1.15 in ± 0.04 in 29.2 mmProvisionalPhoto: Magpul's feature image 03 for MAG426: the OD green hand guard on a rifle with an A2 front sight, the rifle's right side seen level, 700 x 525
Photo 1.15 in ± 0.04 in used
Magpul's feature image 03 for MAG426: the OD green hand guard on a rifle with an A2 front sight, the rifle's right side seen level, 700 x 525, harvested
Scale: visible_length, 9.08 in over 371 px: 40.86 px/in (the M-LOK slots give 40.82). Read by the barrel's axis ahead of the front sight (its silhouette rows 186.5 to 210.5 from column 580 to 695, level: centre 198.5) to the body's top (row 151.5): 47 px; ± 1.5 px
Its body's bottom (clear of the lip) below the bore axis1.19 in ± 0.04 in 30.2 mmProvisionalPhoto: Magpul's feature image 03 for MAG426: the OD green hand guard on a rifle with an A2 front sight, the rifle's right side seen level, 700 x 525
Photo 1.19 in ± 0.04 in used
Magpul's feature image 03 for MAG426: the OD green hand guard on a rifle with an A2 front sight, the rifle's right side seen level, 700 x 525, harvested
Scale: visible_length, 9.08 in over 371 px: 40.86 px/in. Read by the barrel's axis (row 198.5) to the body's bottom (row 247.0, columns 165 to 465): 48.5 px; ± 1.5 px
The body is near centred on the bore: 1.15 above and 1.19 below.
The seam between its two halves, on the sides, above the bore axis (negative below)-0.245 in ± 0.03 in -6.2 mmProvisionalPhoto: Magpul's feature image 03 for MAG426: the OD green hand guard on a rifle with an A2 front sight, the rifle's right side seen level, 700 x 525
Photo -0.245 in ± 0.03 in used
Magpul's feature image 03 for MAG426: the OD green hand guard on a rifle with an A2 front sight, the rifle's right side seen level, 700 x 525, harvested
Scale: visible_length: 40.86 px/in. Read by the dark line along its side (rows 208 to 209 at columns 230 and 260, luminance 93 to 105 between 124 above and 110 below), 10 px under the axis (row 198.5); ± 1 px
The upper half reaches below the axis; the lower one slides into it (its instructions' step 3) and its edge stands over the upper's along the seam.
The room inside its M-LOK faces before what runs through it (how far an accessory's nuts may reach in)No value yetMissingNo source yet
Depends on the barrel, the gas tube and the heat shield under it, and on the wall, which no view gives: no figure, so the check reads as unmade.
M-LOK slots in each upper side face (the two and ten o'clock rows)3ProvisionalPhoto: Magpul's feature image 03, the OD green on a rifle, its right side
Photo 3 count used
Magpul's feature image 03, the OD green on a rifle, its right side, harvested
Scale: none: a count. Read by three slots in the right side's row; three in the left's on Primary Arms' black (41a80c61cadb) and Flat Dark Earth (59d61863c88f) photos and on Magpul's gray on a rifle (32f412d17d79); the instruction sheet draws three for each length
The side rows' rearmost M-LOK slot (its centre), from its rear end3.91 in ± 0.04 in 99.3 mmProvisionalPhoto: Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525
Photo 3.91 in ± 0.04 in used
Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525, harvested
Scale: visible_length: 40.86 px/in. Read by the rearmost slot's centre (column 295.5, between its edges at 269.5 and 321.6 at half the luminance step) less the outline's rear edge (140.5): 155 px = 3.79 in, plus the skirt the rear end stands in (visible_rear_x, 0.12); ± 1.5 px. The next two at 359.9 and 424.1: 64.3 px apart, the standard's pitch
The side rows' slot centres above the bore axis0.22 in ± 0.03 in 5.6 mmProvisionalPhoto: Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525
Photo 0.22 in ± 0.03 in used
Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525, harvested
Scale: visible_length: 40.86 px/in. Read by each slot's edges at half the luminance step down its middle column (rows 183.8 and 195.3 at columns 295, 360 and 424): centre 189.5, 9 px over the axis (row 198.5); ± 1 px
The side M-LOK faces' outward direction about the bore axis, from straight up (degrees)78° ± 10°ConflictPhoto: Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525
Published “M-LOK slots at the two, six, and ten o'clock positions”
Magpul, MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4, Model MAG426: Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Photo 78 deg ± 10 deg used
Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525, harvested
Scale: visible_length: 40.86 px/in. Read by each slot's height in the level side view, 11.5 px (rows 183.8 to 195.3), against the standard's 7 mm width (std.mlok.slot_width, 11.26 px): a face that leans no more than about 20° from upright (cos ≥ 0.93 at ± 1 px), and its slot's centre 0.22 above the axis at the side: about two and a half o'clock
Magpul's "two ... ten o'clock" says which faces, not their angle: a face 60° from up would show its 7 mm slots 0.24 in tall in a level side view, and they show 0.28 (11.5 px) in Magpul's own photo, the slot's centre a fifth of an inch over the axis. The accessories on them stand out at the angle the faces have.
magpul and photo differ by 18° beyond what each states it is good to.
The side M-LOK faces' distance from the bore axis (along their outward direction)1.059 in ± 0.04 in 26.9 mmProvisionalWorked out: ({.width} / 2 - {.face_flat} / 2 * cos({.mlok_side_face_angle})) * sin({.mlok_side_face_angle}) + {.mlok_side_slot_y} * cos({.mlok_side_face_angle})
Worked out 1.0587 in ± 0.04 in used
({.width} / 2 - {.face_flat} / 2 * cos({.mlok_side_face_angle})) * sin({.mlok_side_face_angle}) + {.mlok_side_slot_y} * cos({.mlok_side_face_angle}), harvested
The face's flat runs up from the side at full width (its lower edge), leaning in at the face's angle, its middle where the photo has the slots' centres (mlok_side_slot_y): the plane through it. As good as the width and the face's angle, which no view gives square.
The underside's M-LOK face, its distance below the bore axis1.19 in ± 0.04 in 30.2 mmProvisionalWorked out: {.bottom_below_axis}
Worked out 1.19 in ± 0.04 in used
{.bottom_below_axis}, harvested
M-LOK slots in the underside (six o'clock)3ProvisionalWorked out: {.mlok_side_slots}
Worked out 3 count used
{.mlok_side_slots}, harvested
The underside's rearmost M-LOK slot (its centre), from its rear end3.91 in ± 0.5 in 99.3 mmProvisionalWorked out: {.mlok_side_slot0_x}
Worked out 3.91 in ± 0.5 in used
{.mlok_side_slot0_x}, harvested
The pockets along each side of the lower half (one in each panel between its ribs)6ProvisionalPhoto: Magpul's feature image 03, the OD green on a rifle, its right side
Photo 6 count used
Magpul's feature image 03, the OD green on a rifle, its right side, harvested
Scale: none: a count. Read by six along row 233 (dark runs at columns 175 to 426); six on Magpul's gray on a rifle (32f412d17d79) and on Primary Arms' black (41a80c61cadb)
The lower half's rearmost pocket (its centre), from its rear end1.38 in ± 0.04 in 35.1 mmProvisionalPhoto: Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525
Photo 1.38 in ± 0.04 in used
Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525, harvested
Scale: visible_length: 40.86 px/in. Read by the dark runs along row 233 (each pocket's shaded upper edge): centres at 187.9, 233.0, 277.9, 323.1, 367.8 and 412.6, the rearmost 47.4 px ahead of the outline's rear edge (140.5) = 1.16, plus the skirt (visible_rear_x, 0.12); ± 1.5 px
The lower half's pockets, centre to centre1.1 in ± 0.01 in 27.9 mmProvisionalPhoto: Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525
Photo 1.1 in ± 0.01 in used
Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525, harvested
Scale: visible_length: 40.86 px/in. Read by five gaps between the six pockets' centres, 224.7 px from the first to the last: 44.94 px each
Each pocket's length along it0.63 in ± 0.03 in 16 mmProvisionalPhoto: Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525
Photo 0.63 in ± 0.03 in used
Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525, harvested
Scale: visible_length: 40.86 px/in. Read by the six dark runs along row 233, 25.1 to 26.4 px (mean 25.7); ± 1 px
The pockets' centres above the bore axis (negative below)-0.85 in ± 0.04 in -21.6 mmProvisionalPhoto: Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525
Photo -0.85 in ± 0.04 in used
Magpul's feature image 03, the OD green on a rifle, its right side seen level, 700 x 525, harvested
Scale: visible_length: 40.86 px/in. Read by the pockets' shaded edge at row 233 (luminance 53 between 86 and 89), 34.5 px under the axis (row 198.5); ± 1.5 px
Each pocket's height0.13 in ± 0.04 in 3.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: the level side view shows only each pocket's shaded upper wall (3 px); Primary Arms' black one from the front and above (41a80c61cadb) draws them about a fifth as tall as long.
Worked out 0.13 in ± 0.04 in used
An assumption for the drawing, not a reading: the level side view shows only each pocket's shaded upper wall (3 px); Primary Arms' black one from the front and above (41a80c61cadb) draws them about a fifth as tall as long., harvested
The vents along its crown6ProvisionalPhoto: Magpul's gallery, the Stealth Gray MAG426 alone from above its right side and behind, 800 x 800
Photo 6 count used
Magpul's gallery, the Stealth Gray MAG426 alone from above its right side and behind, 800 x 800, harvested
Scale: none: a count. Read by six rounded slots along the top; six on the black (07350227f7db), Flat Dark Earth (b6a0330a8c69) and OD green (60dc2d9c87c2) shots of the same pose, and the instruction sheet's drawing of the mid-length
The rearmost vent's middle, from its rear end2.25 in ± 0.15 in 57.1 mmProvisionalPhoto: Magpul's gallery, the Stealth Gray MAG426 alone from above its right side and behind, 800 x 800
Photo 2.25 in ± 0.15 in used
Magpul's gallery, the Stealth Gray MAG426 alone from above its right side and behind, 800 x 800, harvested
Scale: its three right side M-LOK slots in the same photo (columns 302, 410 and 526) at their places in the ledger (mlok_side_slot0_x and the standard's pitch): 0.0146 in a column at the rear, 0.0136 at the front. Read by the vents' middles along the crown, columns 188, 262, 338, 420, 504 and 594 (by eye on a crop at 2.5 times), carried along the axis by the slots' columns: 2.25, 3.33, 4.43, 5.55, 6.76, 7.94. The crown stands above and inside the side face, a view from above and behind moves it along by an amount the photo doesn't give: the ±
The vents, middle to middle1.14 in ± 0.05 in 29 mmProvisionalPhoto: Magpul's gallery, the Stealth Gray MAG426 alone from above its right side and behind, 800 x 800
Photo 1.14 in ± 0.05 in used
Magpul's gallery, the Stealth Gray MAG426 alone from above its right side and behind, 800 x 800, harvested
Scale: the same slots' columns. Read by the first and the last vent's places, 5.69 in apart over five gaps
Each vent's length along it0.65 in ± 0.1 in 16.5 mmProvisionalPhoto: Magpul's gallery, the Stealth Gray MAG426 alone from above its right side and behind, 800 x 800
Photo 0.65 in ± 0.1 in used
Magpul's gallery, the Stealth Gray MAG426 alone from above its right side and behind, 800 x 800, harvested
Scale: the same slots' columns (about 69 px to the inch along the axis there). Read by each vent 44 to 52 columns long (by eye on the crop)
Each vent's width across the crown0.16 in ± 0.05 in 4.1 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view looks down on the crown square; in the three-quarter shots each vent is about a quarter as wide as long, foreshortened by an angle the photo doesn't give.
Worked out 0.16 in ± 0.05 in used
An assumption for the drawing, not a reading: no view looks down on the crown square; in the three-quarter shots each vent is about a quarter as wide as long, foreshortened by an angle the photo doesn't give., harvested
The ribs between the lower half's panels (and round them), their width0.12 in ± 0.04 in 3 mmProvisionalWorked out: An assumption for the drawing, not a reading: the ribs show as lit and shaded lines a few pixels wide between the pockets in the photos on file, their width and how far they stand on no view in section.
Worked out 0.12 in ± 0.04 in used
An assumption for the drawing, not a reading: the ribs show as lit and shaded lines a few pixels wide between the pockets in the photos on file, their width and how far they stand on no view in section., harvested
How far the lower half's panels stand in from its ribs0.02 in ± 0.01 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the panels' edges catch the light in the three-quarter photos, how deep they are isn't seen in profile.
Worked out 0.02 in ± 0.01 in used
An assumption for the drawing, not a reading: the panels' edges catch the light in the three-quarter photos, how deep they are isn't seen in profile., harvested
Each pocket's depth into the wall0.06 in ± 0.03 in 1.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows a pocket in section; they aren't through (the OD green one's show its own colour, not the barrel).
Worked out 0.06 in ± 0.03 in used
An assumption for the drawing, not a reading: no view on file shows a pocket in section; they aren't through (the OD green one's show its own colour, not the barrel)., harvested
Its polymer wall's thickness0.15 in ± 0.05 in 3.8 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows an end square on or a section. Taken so that the model comes near Magpul's 8.7 oz at the polymer's density on file (std.density.polymer, an unfilled nylon) with its aluminium heat shield: at 0.1 in it was 38% light. What it still lacks is the inner ribs and bosses no view shows.
Worked out 0.15 in ± 0.05 in used
An assumption for the drawing, not a reading: no view on file shows an end square on or a section. Taken so that the model comes near Magpul's 8.7 oz at the polymer's density on file (std.density.polymer, an unfilled nylon) with its aluminium heat shield: at 0.1 in it was 38% light. What it still lacks is the inner ribs and bosses no view shows., harvested
Its aluminium heat shield's thickness0.03 in ± 0.015 in 0.8 mmProvisionalWorked out: An assumption for the drawing, not a reading: the shield shows only through the slots and at the open front end, never in section.
Worked out 0.03 in ± 0.015 in used
An assumption for the drawing, not a reading: the shield shows only through the slots and at the open front end, never in section., harvested
The seam's groove along each side (its width and its depth)0.02 in ± 0.01 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the seam shows as a dark line one or two pixels wide at 41 px to the inch (0.025 to 0.05 in), its depth on no view.
Worked out 0.02 in ± 0.01 in used
An assumption for the drawing, not a reading: the seam shows as a dark line one or two pixels wide at 41 px to the inch (0.025 to 0.05 in), its depth on no view., harvested
Each upper side face's flat (where its M-LOK slots are), its height across the face0.62 in ± 0.1 in 15.7 mmProvisionalWorked out: An assumption for the drawing, not a reading: the slot's 7 mm and a margin each side as wide as the slots' 8 mm webs, which is how Primary Arms' black one (41a80c61cadb) shows the raised band round its slots.
Worked out 0.62 in ± 0.1 in used
An assumption for the drawing, not a reading: the slot's 7 mm and a margin each side as wide as the slots' 8 mm webs, which is how Primary Arms' black one (41a80c61cadb) shows the raised band round its slots., harvested
Its top's flat (the crown, between the upper side faces' rounds), half its width0.5 in ± 0.15 in 12.7 mmProvisionalWorked out: An assumption for the drawing, not a reading: no end view on file; the three-quarter photos (41a80c61cadb, 431dc8b3dc62 of the carbine) show a rounded crown about as wide as the bore's two sides above the faces.
Worked out 0.5 in ± 0.15 in used
An assumption for the drawing, not a reading: no end view on file; the three-quarter photos (41a80c61cadb, 431dc8b3dc62 of the carbine) show a rounded crown about as wide as the bore's two sides above the faces., harvested
Its underside's flat (where the six o'clock slots are), half its width0.45 in ± 0.15 in 11.4 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file looks at the underside; Magpul's carbine with its MVG on (8e445b9aae44) shows a flat underside a little narrower than the grip's base, rounding into the sides.
Worked out 0.45 in ± 0.15 in used
An assumption for the drawing, not a reading: no view on file looks at the underside; Magpul's carbine with its MVG on (8e445b9aae44) shows a flat underside a little narrower than the grip's base, rounding into the sides., harvested
Its front flange (what goes into the hand guard cap), outside diameter1.36 in ± 0.05 in 34.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the flange goes "into the metal Hand Guard cap" (its instructions) and Magpul says it takes a round or a triangular cap; no view shows it but end-on from the front (the carbine's 431dc8b3dc62: an arc inside the body). Taken inside both caps on file: the triangular cap's sides stand 0.689 from the axis inside at their middles (bcm-handguard-cap-triangle-750: side_r less side_centre_r less the sheet), the round cap's two tabs at 3 and 9 o'clock to 0.690.
Worked out 1.36 in ± 0.05 in used
An assumption for the drawing, not a reading: the flange goes "into the metal Hand Guard cap" (its instructions) and Magpul says it takes a round or a triangular cap; no view shows it but end-on from the front (the carbine's 431dc8b3dc62: an arc inside the body). Taken inside both caps on file: the triangular cap's sides stand 0.689 from the axis inside at their middles (bcm-handguard-cap-triangle-750: side_r less side_centre_r less the sheet), the round cap's two tabs at 3 and 9 o'clock to 0.690., harvested
Its front flange's length (into the cap)0.42 in ± 0.1 in 10.7 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view shows the flange from the side. Long enough that the front wall it stands from stays behind either cap's rim with the flange home (the round cap is 0.276 deep, the triangular 0.323).
Worked out 0.42 in ± 0.1 in used
An assumption for the drawing, not a reading: no view shows the flange from the side. Long enough that the front wall it stands from stays behind either cap's rim with the flange home (the round cap is 0.276 deep, the triangular 0.323)., harvested
Its rear end (what stands in the delta ring's skirt), outside diameter1.72 in ± 0.03 in 43.7 mmProvisionalWorked out: An assumption for the drawing, not a reading: its rear end stands in the delta ring's skirt (std.ar15.slip_ring_skirt_d, 1.750 inside) and shows on no photo; taken 0.03 under the skirt.
Worked out 1.72 in ± 0.03 in used
An assumption for the drawing, not a reading: its rear end stands in the delta ring's skirt (std.ar15.slip_ring_skirt_d, 1.750 inside) and shows on no photo; taken 0.03 under the skirt., harvested
Its front wall (the inner face the front flange stands from), from its rear end8.03 in ± 0.12 in 204 mmProvisionalWorked out: {.mounting_length} - {.front_flange_length} - {.wall}
Worked out 8.03 in ± 0.12 in used
{.mounting_length} - {.front_flange_length} - {.wall}, harvested
Ahead of the wall the shell runs on open to its front tip, over the cap and the front sight base's rear ("Hand guard will wrap around the front sight when mounted").
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Drop-in handguard's front in its cap
Handguard mount
Drop-in handguard's hold
- Delta rings
- BCM Delta Ring Assembly - AR15
Gas system length
- Barrels
- Aero Precision 16" 5.56 CMV barrel, mid-length, BCM Standard 14.5" Mid Length Barrel, Stripped, BCM Standard 16" Mid Length Barrel, Stripped, Bear Creek Arsenal BC-15 5.56 NATO, 16" Parkerized M4 Barrel, 1:7 Twist, Mid-Length Gas System, Faxon Firearms Duty Series Pencil Profile 16" Mid-Length 5.56 NATO AR15 Barrel, Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 13.9", Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 14.5", Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 16"
M-LOK
- Hand stops
- BCM KAG (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK Hand Stop (fit unchecked), Magpul M-LOK Index Panel (fit unchecked)
- Vertical grips
- BCM Vertical Grip Mod 3 (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK MVG vertical grip (fit unchecked)
- Lights
- Cloud Defensive REIN (fit unchecked), Streamlight ProTac Rail Mount HL-X (fit unchecked), SureFire Mini Scout Light Pro (fit unchecked), SureFire Scout Light Pro Dual Fuel (fit unchecked)
- Rail sections
- Magpul M-LOK® Aluminum Rail, 3 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 5 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 7 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 9 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 11 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 3 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 5 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 7 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 9 Slots (fit unchecked)
- Adapter plates
- Magpul M-LOK Hand Stop MOE Adapter (fit unchecked)
- Sling mounts
- Magpul M-LOK QD Sling Mount (fit unchecked)
- Rail covers
- Magpul M-LOK Rail Cover Type 2 (fit unchecked)
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- KYGUNCO $28.80 Stealth Gray Nov 21, 2026, in stock that day
- Primary Arms $29.84 Flat Dark Earth Nov 21, 2026, in stock that day
- Primary Arms $29.84 Olive Drab Green Nov 21, 2026, in stock that day
- Primary Arms $29.84 Black Nov 17, 2026, in stock that day
- Midwest Gun Works $35.10 Black Nov 21, 2026, in stock that day
- Midwest Gun Works $35.10 Flat Dark Earth Nov 21, 2026, in stock that day
- Midwest Gun Works $35.10 Olive Drab Green Nov 21, 2026, in stock that day
- Midwest Gun Works $35.10 Stealth Gray Nov 21, 2026, in stock that day
- Magpul $36.95 Black Nov 21, 2026, stock not said
- Magpul $36.95 Flat Dark Earth Nov 21, 2026, stock not said
- Magpul $36.95 Olive Drab Green Nov 21, 2026, stock not said
- Magpul $36.95 Stealth Gray Nov 21, 2026, stock not said