Light
Streamlight ProTac Rail Mount HL-X
Streamlight's ProTac Rail Mount HL-X long gun light: 1,000 lumens, a machined aluminium body, a push-button tail switch or the remote pressure switch that comes with it. "Integrated rail clamp attaches to MIL-STD-1913 (Picatinny) rails", and the M-LOK mount in the box (Streamlight 88300) holds it on a handguard's slot, over its top corner and leaning out. Black only.

- Weight
- 6.4 oz ± 0.05 oz Conflictpublished: Streamlight, Product Fact Sheet: ProTac Rail Mount HL-X // ProTac Rail Mount HL-X USB (Document #297, Rev 4, revised 09/18/2023), the maker, read Oct 5, 2026Its sources span 5.65 oz to 6.95 oz.
- Lowest price
- $119.99 at Primary Arms, read Nov 17, 2026 (Two CR123A cells (88066))
- Maker's number
- 88066
- Colour
- Black (placeholder)
- Drawn as
- modelled
- Maker's page
- streamlight.com
In “Aero 5.56 carbine, fitted out”, a build on the start page, in place of its SureFire Scout Light Pro Dual Fuel.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Weight with the SL-B26 rechargeable pack (item 88071), the rail clamp on6.9 oz ± 0.05 ozConflictPublished: Streamlight, Product Fact Sheet: ProTac Rail Mount HL-X // ProTac Rail Mount HL-X USB (Document #297, Rev 4, revised 09/18/2023), the maker, read Oct 5, 2026
Published “6.9 oz (195.6 g) with SL-B26 rechargeable battery pack” used
Streamlight, Product Fact Sheet: ProTac Rail Mount HL-X // ProTac Rail Mount HL-X USB (Document #297, Rev 4, revised 09/18/2023), the maker, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “WEIGHT: CR123A 6.4 oz (181.4g) // SL-B26 6.9 oz (195.6g)”
Streamlight, ProTac Rail Mount HL-X info sheet with part numbers (6/25), Dimensions, the maker, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “Weight (Max) 6.90 ounces (195.61 grams)”
Streamlight, ProTac Rail Mount HL-X (PROTAC RAIL MOUNT HL-X LONG GUN LIGHT), Product Specifications, the maker, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “Weight 6.9oz”
Sportsman's Warehouse, Streamlight Protac Rail Mount HL-X Long Gun Light - Black (ID 1821926, MPN 88071), Specifications, a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “Weight = 6.4 Ounce”
MidwayUSA, Streamlight ProTac Rail Mount HL-X Rechargeable Weapon Light for Picatinny Rail Black (88071), the page's attribute table, a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
The CR123A figure on the rechargeable package's page (its Battery Type row says SL-B26).
The maker's sheet names the battery; its page and info sheet agree. MidwayUSA's 6.4 Ounce is the other package's figure.
fact-sheet and midwayusa differ by 0.5 oz beyond what each states it is good to.
info-sheet and midwayusa differ by 0.5 oz beyond what each states it is good to.
page and midwayusa differ by 0.5 oz beyond what each states it is good to.
sportsmans and midwayusa differ by 0.5 oz beyond what each states it is good to.
The USB package's weight: the same light with one SL-B26 pack in place of two CR123A cells.
Overall length5.43 in ± 0.005 in 137.9 mmConflictPublished: Streamlight, ProTac Rail Mount HL-X (PROTAC RAIL MOUNT HL-X LONG GUN LIGHT), Product Specifications, the maker, read Oct 5, 2026
Published “Length (Max) 5.43 inches (13.79 centimeters)” used
Streamlight, ProTac Rail Mount HL-X (PROTAC RAIL MOUNT HL-X LONG GUN LIGHT), Product Specifications, the maker, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “DIMENSIONS: Length: 5.43 in (13.8 cm)”
Streamlight, Product Fact Sheet: ProTac Rail Mount HL-X // ProTac Rail Mount HL-X USB (Document #297, Rev 4, revised 09/18/2023), the maker, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “LENGTH: 5.43 in (13.79 cm)”
Streamlight, ProTac Rail Mount HL-X info sheet with part numbers (6/25), Dimensions, the maker, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “Length = 5.43 Inches”
MidwayUSA, Streamlight ProTac Rail Mount HL-X Weapon Light for Picatinny Rail Black (88066), the page's attribute table, a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “Overall Length 5.43"”
Rifle Supply, Streamlight ProTac HL-X Rail Mount | Remote Pressure Switch | 88066 (a listing with the light's earlier beam figures), a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “Length: 13.7 cm”
armamat.ch (a Swiss shop), ProTac Rail Mount HL X, manufacturer number 88066, Dimensions & weight, a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
One decimal, and 0.09 cm under the maker's 13.79: read as that figure cut short, so its ± is a whole last digit.
Published “5.45 IN”
GRITR Outdoors, STREAMLIGHT ProTac Rail Mount HL-X USB 1000 Lumens Long Gun Light (88071): the sixth gallery image, an infographic in the maker's style (references raw 56d3daf98da7), a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
A bracket under a picture of the light, end to end. The same graphic for the HL-X Pro on Streamlight's own page (references raw b587f45305d7) prints 5.43 IN.
The maker's page, fact sheet and info sheet all print 5.43; the infographic's 5.45 stands alone against them.
page and gritr-infographic differ by 0.02 in beyond what each states it is good to.
fact-sheet and gritr-infographic differ by 0.02 in beyond what each states it is good to.
info-sheet and gritr-infographic differ by 0.02 in beyond what each states it is good to.
midwayusa and gritr-infographic differ by 0.02 in beyond what each states it is good to.
rifle-supply and gritr-infographic differ by 0.02 in beyond what each states it is good to.
armamat and gritr-infographic differ by 0.056 in beyond what each states it is good to.
The scale of every photograph here. An infographic in the maker's style on a seller's page prints 5.45 IN where the maker's documents all say 5.43 (the same graphic for the HL-X Pro, on Streamlight's own page, prints 5.43 IN); a Swiss shop's 13.7 cm is the maker's 13.79 cut short.
The fact sheet's "Width" (what it spans isn't said)1.45 in ± 0.005 in 36.8 mmConflictPublished: Streamlight, Product Fact Sheet: ProTac Rail Mount HL-X // ProTac Rail Mount HL-X USB (Document #297, Rev 4, revised 09/18/2023), the maker, read Oct 5, 2026
Published “Width: 1.45 in (3.68 cm)” used
Streamlight, Product Fact Sheet: ProTac Rail Mount HL-X // ProTac Rail Mount HL-X USB (Document #297, Rev 4, revised 09/18/2023), the maker, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “1.45 IN”
GRITR Outdoors, STREAMLIGHT ProTac Rail Mount HL-X USB 1000 Lumens Long Gun Light (88071): the sixth gallery image, an infographic in the maker's style (references raw 56d3daf98da7), a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “Width: 3.3 cm”
armamat.ch (a Swiss shop), ProTac Rail Mount HL X, manufacturer number 88066, Dimensions & weight, a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
The maker's own sheet; the shop's 3.3 cm is its own, unsourced.
fact-sheet and armamat differ by 0.151 in beyond what each states it is good to.
gritr-infographic and armamat differ by 0.151 in beyond what each states it is good to.
Not tied to a feature by any document. The infographic in the maker's style (GRITR's gallery; the HL-X Pro's on Streamlight's own page is the same) draws its 1.45 IN bracket across the head, beside the picture, the thumb wheel left out. The head's largest diameter reads 0.03 in less in the photographs scaled by the published length (head_diameter), so the figure isn't used for scale. A Swiss shop's 3.3 cm for both its width and its height (1.30 in) matches nothing measured here.
The fact sheet's "Height" (what it spans isn't said)1.72 in ± 0.005 in 43.7 mmConflictPublished: Streamlight, Product Fact Sheet: ProTac Rail Mount HL-X // ProTac Rail Mount HL-X USB (Document #297, Rev 4, revised 09/18/2023), the maker, read Oct 5, 2026
Published “Height: 1.72 in (4.37 cm)” used
Streamlight, Product Fact Sheet: ProTac Rail Mount HL-X // ProTac Rail Mount HL-X USB (Document #297, Rev 4, revised 09/18/2023), the maker, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “1.72 IN”
GRITR Outdoors, STREAMLIGHT ProTac Rail Mount HL-X USB 1000 Lumens Long Gun Light (88071): the sixth gallery image, an infographic in the maker's style (references raw 56d3daf98da7), a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “Height: 3.3 cm”
armamat.ch (a Swiss shop), ProTac Rail Mount HL X, manufacturer number 88066, Dimensions & weight, a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
The maker's own sheet; the shop's 3.3 cm is its own, unsourced.
fact-sheet and armamat differ by 0.421 in beyond what each states it is good to.
gritr-infographic and armamat differ by 0.421 in beyond what each states it is good to.
Not tied to a feature by any document. It is what the light measures across its head and out to the end of the clamp's thumb wheel (width): 1.74 in in Primary Arms' photo and 1.70 in the maker's, the wheel screwed further in. The infographic marks its 1.72 IN as a depth, into the picture.
Head diameter (across the cooling fins, its largest)1.424 in ± 0.012 in 36.2 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 1.424 in ± 0.012 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by the four fins' tops to their mirror below the axis: 494.4 to 495.0 px at columns 343, 377, 440 and 479; the +/- is the scale's (0.4%) and two pixels
No document gives it by name. The fact sheet's Width, 1.45 in, is drawn across the head in the infographic (listed_width): 0.03 in more than this. The maker's own side-on photo of a 2016 unit (a61f009b2170) reads 1.418 by its length with no allowance for perspective, and the maker's photo of the light on an M-LOK handguard, scaled by the handguard's slots (83f4380a7ffe: 61.2 px to the 40 mm pitch), 1.41 +/- 0.03. The bezel ahead of the fins is 1.365.
Body diameter (the battery tube)0.92 in ± 0.006 in 23.4 mmCorroboratedPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 0.92 in ± 0.006 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by the tube's width, 319.4 px over columns 862 to 926 and 319.7 px over 1384 to 1544 (the same at both ends: the photo isn't yawed)
Photo 0.917 in ± 0.008 in
Streamlight's gallery image _3: the same view of another unit, S/N 1116 010011, 800 x 800, harvested
Scale: the published length (.length) as the silhouette tip to tip, 783 px, with nothing taken off for perspective (its end sections read 2% shorter against its tube than Primary Arms': a longer lens). Read by the tube's width, 132.4 px over columns 322 to 350 and 545 to 600
The photo the outlines are traced from, at two and a half times the resolution, with its perspective taken off; the maker's own photo of another unit agrees within 0.4%.
The plain tube either side of the clamp. The two bands the clamp's legs hang from are 0.933, the neck ring behind the head 1.048, the tail cap's knurled grip 1.014.
The body's axis above the rail's top (on its rail clamp)0.773 in ± 0.05 in 19.6 mmProvisionalWorked out: {.bolt_below_axis} - ({std.picatinny.slot_depth} - {.stud_diameter} / 2)
Worked out 0.773 in ± 0.05 in used
{.bolt_below_axis} - ({std.picatinny.slot_depth} - {.stud_diameter} / 2), harvested
Photo 0.73 in ± 0.04 in
Streamlight's gallery image _5: a handguard from its right side, the light on its M-LOK mount, 800 x 800, harvested
Scale: the handguard's M-LOK slots: 61.2 px to the 40 mm pitch (std.mlok.slot_pitch), 38.9 px/in. Read by the body's axis (row 274.5: the tube's edges at 257 and 292) to the legs' lower ends at the mount's top edge (row 303), 28.5 px; one pixel is 0.026 in. The legs' feet taken as what sits on a rail's top
The clamp's own bolt, placed by the standard's slot; the M-LOK photo is 39 px to the inch and agrees within both +/-.
On the Picatinny clamp. Not published and in no straight view: the clamp's cross bolt is 0.81 below the axis (bolt_below_axis), and the bolt lies in a slot of the rail, here taken as resting on the slot's floor (it can sit no lower; riding higher would put the light up to 0.03 in nearer the rail). The same figure is the light's axis above the M-LOK mount's floor, where its legs stand. The mlok-photo row was read (batch 3) as the legs' feet at the mount's top edge in the maker's side view; the mount is known since 2026-10-19 to hold the legs on a floor leaning up from the plate's top edge (mlok_seat_angle), so what that row measures is the axis above the plate's top edge, which the mount's figures put at 0.80: the check is mlok_axis_above_screws.
The clamp's cross bolt (the thumb wheel's stud) below the body's axis0.807 in ± 0.04 in 20.5 mmCorroboratedPhoto: Primary Arms 88066_01.jpg: the same unit from behind and above, thumb wheel toward the lens, 2200 x 1467
Photo 0.807 in ± 0.04 in used
Primary Arms 88066_01.jpg: the same unit from behind and above, thumb wheel toward the lens, 2200 x 1467, harvested
Scale: a camera fitted to the body's silhouette (the plan view's radii along the axis; focal length 8000 px, the lens 19.3 in off, rms 1.3 px away from the clamp and the ends). Read by the stud's end face is a circle about the clamp's cross axis: its hex socket's ellipse (centre 1302.6, 1123.0; short axis at 24.2 degrees) gives the light's turn about its own axis and puts the stud's axis 0.807 below the body's, at the clamp's middle. The +/- covers two pixels on the ellipse and the fit
Photo 0.86 in ± 0.05 in
GRITR's copy of the maker's kit picture for 88071: the light from its left side and from about 30 degrees above, the clamp's fixed jaw toward the lens, 1601 x 1601; engraved S/N 358732 0522, harvested
Scale: the tube's width there, 141.5 px, as .body_diameter: 153.8 px/in. Read by the bolt head's centre on the fixed jaw's face reads 1.01 in below the axis in the picture (155 px); the face stands 0.55 in nearer the lens, and for a view from 20 to 45 degrees above the side that puts the bolt 0.85 to 0.88 below the axis
A fitted camera on a 2200 px photo; the kit picture's angle is known only from where the engraving shows, and its reading agrees within both +/-.
The cross bolt's (stud's) diameter0.167 in ± 0.008 in 4.2 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 0.167 in ± 0.008 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by the stud's end where it stands out of the thumb wheel: columns 1114 to 1171 at row 430, 58 px
Overall width, across the head and out to the thumb wheel's end (as photographed)1.766 in ± 0.012 in 44.9 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 1.766 in ± 0.012 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by the stud's end (row 426.1) to the head's far side (row 1039.5): 613.4 px
With the rail clamp on. The wheel screws in as the clamp closes: the maker's own photo (a61f009b2170) reads 1.71 in. The fact sheet's Height, 1.72 in, sits between the two (listed_height).
The bezel's front ahead of the clamp's middle2.946 in ± 0.015 in 74.8 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 2.946 in ± 0.015 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by the clamp's middle is the thumb wheel's centre (column 1142.0: the wheel spans 1034 to 1250); the bezel's tip shows at column 87.8, 30.9 px ahead of its plane (its near tooth stands 0.68 in nearer the lens)
The tail cap's end behind the clamp's middle2.483 in ± 0.015 in 63.1 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 2.483 in ± 0.015 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by the tail guard's tip shows at column 2023.4, 18.9 px behind its plane (its near ear stands 0.46 in nearer the lens)
With the push-button tail cap. front_x and rear_x add up to the published length: the scale was set so.
The clamp's length along the rail (its moving jaw)1.215 in ± 0.01 in 30.9 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 1.215 in ± 0.01 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by the moving jaw's block, columns 934 to 1356 (its corners chamfered 0.12 in); the fixed jaw on the other side is 1.09 (958 to 1338)
The fixed jaw's length along the rail1.094 in ± 0.01 in 27.8 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 1.094 in ± 0.01 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by columns 958 to 1338, its two mounting screws' heads at its ends
The moving jaw's outer face from the body's axis (as photographed)0.673 in ± 0.01 in 17.1 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 0.673 in ± 0.01 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by the block's flat outer face at row 556.9, the axis at row 790.6 there: 233.7 px. The jaw moves with the wheel: how far open the clamp is in the photo isn't known
The fixed jaw's outer face from the body's axis0.55 in ± 0.008 in 14 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 0.55 in ± 0.008 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by the jaw's raised middle at row 981.8, the axis at 790.6: 191.2 px. Its face either side is 0.025 in lower (row 973), and its two screws' heads stand 0.022 in off that
The jaws' height (top to bottom of the fixed jaw's face)0.52 in ± 0.05 in 13.2 mmProvisionalPhoto: GRITR's copy of the maker's kit picture for 88071: the light from its left side and from about 30 degrees above, the clamp's fixed jaw toward the lens, 1601 x 1601; engraved S/N 358732 0522
Photo 0.52 in ± 0.05 in used
GRITR's copy of the maker's kit picture for 88071: the light from its left side and from about 30 degrees above, the clamp's fixed jaw toward the lens, 1601 x 1601; engraved S/N 358732 0522, harvested
Scale: the tube's width there, 141.5 px, as .body_diameter: 153.8 px/in. Read by the fixed jaw's face from its top edge (row 485) to its bottom (row 554), 69 px, over the cosine of the view's angle above the side (32 degrees, from where the engraving shows; 25 to 39 changes it by 0.04)
The moving jaw's height0.376 in ± 0.03 in 9.6 mmProvisionalPhoto: Primary Arms 88066_01.jpg: the same unit from behind and above, thumb wheel toward the lens, 2200 x 1467
Photo 0.376 in ± 0.03 in used
Primary Arms 88066_01.jpg: the same unit from behind and above, thumb wheel toward the lens, 2200 x 1467, harvested
Scale: the camera fitted to the body in that photo (as bolt_below_axis: focal length 8000 px, the lens 19.3 in off) and the turn about the axis the stud's end gives. Read by the jaw's rear outer corner edge from its top (pixel 1043, 1030) to its foot (1036, 1179): 0.512 and 0.888 in below the body's axis; the chamfer along its lower edge is 0.04 of that
Shorter than the fixed jaw (jaw_height, 0.52 from the kit picture), which carries the two mounting screws above the cross bolt.
The jaws' lower edge below the cross bolt's axis0.082 in ± 0.025 in 2.1 mmCorroboratedPhoto: Primary Arms 88066_01.jpg: the same unit from behind and above, thumb wheel toward the lens, 2200 x 1467
Photo 0.1 in ± 0.03 in
GRITR's copy of the maker's kit picture for 88071: the light from its left side and from about 30 degrees above, the clamp's fixed jaw toward the lens, 1601 x 1601; engraved S/N 358732 0522, harvested
Scale: the tube's width there, 141.5 px, as .body_diameter: 153.8 px/in. Read by the bolt head's centre (row 540) to the jaw's lower edge (row 554), 14 px, over the cosine of 32 degrees
Photo 0.082 in ± 0.025 in used
Primary Arms 88066_01.jpg: the same unit from behind and above, thumb wheel toward the lens, 2200 x 1467, harvested
Scale: the camera fitted to the body in that photo (as bolt_below_axis: focal length 8000 px, the lens 19.3 in off) and the turn about the axis the stud's end gives. Read by the moving jaw's rear outer corner edge, taken as standing square to the rail at the jaw's rear end (x = -clamp_length / 2): its foot, with the chamfer along the jaw's lower edge, at pixel (1036, 1179) is 0.888 in below the body's axis, the bolt 0.807
Read through a fitted camera; the kit picture's reading on the other jaw depends on its angle, and agrees within both +/-.
The two mounting screws above the cross bolt's axis0.18 in ± 0.03 in 4.6 mmProvisionalPhoto: GRITR's copy of the maker's kit picture for 88071: the light from its left side and from about 30 degrees above, the clamp's fixed jaw toward the lens, 1601 x 1601; engraved S/N 358732 0522
Photo 0.18 in ± 0.03 in used
GRITR's copy of the maker's kit picture for 88071: the light from its left side and from about 30 degrees above, the clamp's fixed jaw toward the lens, 1601 x 1601; engraved S/N 358732 0522, harvested
Scale: the tube's width there, 141.5 px, as .body_diameter: 153.8 px/in. Read by the screw heads' centres (rows 513.5 and 520, the picture turned 1.2 degrees) 23 px above the bolt head's, over the cosine of 32 degrees
The two mounting screws, centre to centre along the rail0.895 in ± 0.012 in 22.7 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 0.895 in ± 0.012 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by their heads' middles at columns 992.5 and 1303.5 (each head 68 px, 0.196 in, across)
The mounting screws' head diameter0.196 in ± 0.01 in 5 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 0.196 in ± 0.01 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by each head 68 px across where it stands off the fixed jaw (columns 958 to 1026 and 1270 to 1337)
The cross bolt's head on the fixed jaw0.23 in ± 0.02 in 5.8 mmProvisionalPhoto: GRITR's copy of the maker's kit picture for 88071: the light from its left side and from about 30 degrees above, the clamp's fixed jaw toward the lens, 1601 x 1601; engraved S/N 358732 0522
Photo 0.23 in ± 0.02 in used
GRITR's copy of the maker's kit picture for 88071: the light from its left side and from about 30 degrees above, the clamp's fixed jaw toward the lens, 1601 x 1601; engraved S/N 358732 0522, harvested
Scale: the tube's width there, 141.5 px, as .body_diameter: 153.8 px/in. Read by the round head at the jaw's lower edge, 35 px across along the light
The thumb wheel's diameter0.625 in ± 0.006 in 15.9 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 0.625 in ± 0.006 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by columns 1034 to 1250 at rows 440 to 520: 217 px
The thumb wheel's thickness (its knurled rim)0.262 in ± 0.01 in 6.7 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 0.262 in ± 0.01 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by rows 434 to 525: 91 px; a collar 0.41 in across (141 px) carries it 0.09 in off the jaw (rows 525 to 557)
The stud's end beyond the wheel, from the body's axis (as photographed)1.05 in ± 0.01 in 26.7 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 1.05 in ± 0.01 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by the stud's end at row 426.1, the axis at 790.6: 364.5 px; the wheel's own outer face is 0.017 in short of it (row 432)
The collar between the thumb wheel and the moving jaw0.406 in ± 0.01 in 10.3 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 0.406 in ± 0.01 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by columns 1073 to 1213 at row 540: 141 px
The two bands on the body that the clamp's legs hang from0.933 in ± 0.006 in 23.7 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 0.933 in ± 0.006 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by the band's lower edge where it shows ahead of the fixed jaw (columns 936 to 956): 162.0 px from the axis, the tube 159.8
The body between the two bands (where it is engraved)0.852 in ± 0.012 in 21.6 mmProvisionalPhoto: GRITR's copy of the maker's kit picture for 88071: the light from its left side and from about 30 degrees above, the clamp's fixed jaw toward the lens, 1601 x 1601; engraved S/N 358732 0522
Photo 0.852 in ± 0.012 in used
GRITR's copy of the maker's kit picture for 88071: the light from its left side and from about 30 degrees above, the clamp's fixed jaw toward the lens, 1601 x 1601; engraved S/N 358732 0522, harvested
Scale: the tube's width there, 141.5 px, as .body_diameter: 153.8 px/in. Read by the body's upper edge stands 6.2 px lower between the bands (row 320.1 over columns 740 to 812) than on the front band (312.5) and the rear one (314.9), the picture's 1.2 degree turn allowed for: 0.040 in under the bands' radius (.band_diameter). The tube beside the rear band is 1 px under it, as the plan view has it
A turned body's upper edge shows its radius from any side, so the kit picture's angle doesn't matter here. In the plan view the clamp's jaws hide this zone's sides.
The front band's front edge ahead of the clamp's middle0.605 in ± 0.01 in 15.4 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 0.605 in ± 0.01 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by column 932 (the clamp's middle at 1142); the band runs back to column 1060, 0.37 in
The rear band's rear edge behind the clamp's middle0.622 in ± 0.01 in 15.8 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 0.622 in ± 0.01 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by column 1358; the band runs forward to column 1255, 0.30 in
Each band's (and each leg's) length along the body0.33 in ± 0.04 in 8.4 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 0.33 in ± 0.04 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: the published length (.length, 5.43 in) as the silhouette tip to tip (1935.6 px) less 49.8 px for the two end rims standing nearer the lens: 347.3 px/in at the axis. The lens stood about 23 in off: a camera fitted to the body in the same seller's oblique photo of this unit (0c0f9c6bb6f9) has a focal length of 8000 px, best of 6000 to 15000. Read by the front band 128 px (0.37 in), the rear one 103 px (0.30): their mean; the +/- takes in both
The glass as it shows inside the bezel1.05 in ± 0.03 in 26.7 mmProvisionalPhoto: Primary Arms 88066_02.jpg: the same unit from ahead, 2200 x 1467
Photo 1.05 in ± 0.03 in used
Primary Arms 88066_02.jpg: the same unit from ahead, 2200 x 1467, harvested
Scale: the bezel's own diameter across the same line, 426 px, as 1.365 in (profiles.body: 474.2 px in the plan view). Read by the luminance across the head's front face through its centre (416, 1196), square to the body's axis in the picture: bright from 160 px one side to 168 px the other, the bezel's wall dark outside it
The moving jaw's corner chamfers (in plan)0.12 in ± 0.015 in 3 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 0.12 in ± 0.015 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: 347.3 px/in at the axis (as body_diameter: the published length less the end rims' perspective). Read by each end of the block's outer face is cut back from column 934 to 976 (42 px along) and from row 594 to 557 (37 px across)
The thumb wheel's outer face from the body's axis (as photographed)1.033 in ± 0.01 in 26.2 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 1.033 in ± 0.01 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: 347.3 px/in at the axis (as body_diameter: the published length less the end rims' perspective). Read by the wheel's rim ends at row 432 (the axis at 790.6): 358.6 px
The fixed jaw's raised middle above the face either side of it0.025 in ± 0.006 in 0.6 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 0.025 in ± 0.006 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: 347.3 px/in at the axis (as body_diameter: the published length less the end rims' perspective). Read by rows 981.8 (the middle) and 973 (the face beside the screw heads): 8.8 px
The fixed jaw's raised middle, its length along the rail0.54 in ± 0.02 in 13.7 mmProvisionalPhoto: Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720
Photo 0.54 in ± 0.02 in used
Primary Arms 88066_00.jpg: the light straight from above its clamp, thumb wheel up, lens to the left, on white, 2200 x 1467; engraved ProTac Rail Mount HL-X S/N 162953 0720, harvested
Scale: 347.3 px/in at the axis (as body_diameter: the published length less the end rims' perspective). Read by columns 1055 to 1243: 188 px
M-LOK slots its mount's lugs span1ProvisionalPhoto: Streamlight's gallery image _5: a handguard from its right side, the light on its M-LOK mount, 800 x 800
Photo 1 count used
Streamlight's gallery image _5: a handguard from its right side, the light on its M-LOK mount, 800 x 800, harvested
Scale: the handguard's M-LOK slots: 61.2 px to the 40 mm pitch (std.mlok.slot_pitch). Read by the mount's plate (columns 464 to 520) covers the slot between the ones at 407 to 455 and 530 to 578; its two screws at columns 477 and 508
The M-LOK mount (Streamlight item 88300, in both packages; modelled since 2026-10-19, batch 13: the mlok_ entries below). Its two T-nut screws are 31 px apart in the maker's side view (20.3 mm by the slots' pitch) and both sit in one slot, which its plate covers; Streamlight's _4 and its HL-X Pro and Rail Mount 2 pictures (40f51d600bbb, 39df28d719d2) show the same, each a three-quarter view.
Reach inside the handguard (below the mounting face, tightened)No value yetMissingNo source yet
Not sourced: the instruction sheet gives the M-LOK mount's screws (10-24 x 3/8 in) and no T-nut figure.
The M-LOK mount's length (its plate and seat, one section along it)1.498 in ± 0.06 in 38 mmCorroboratedPhoto: milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L
Photo 1.498 in ± 0.06 in used
milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L, harvested
Scale: the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing). Read by a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ±. The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the mount's length (38.1 mm)
Photo 1.49 in ± 0.04 in
Streamlight's gallery image _5: a handguard from its right side, the HL-X on its M-LOK mount, 800 x 800, harvested
Scale: the handguard's M-LOK slots: 61.2 px to the 40 mm pitch (std.mlok.slot_pitch), 38.9 px/in in the face's plane. Read by the plate's two ends, columns 464 to 522 (58 px); one pixel is 0.026 in
Four photos of the mount alone through fitted cameras; the maker's side view of it on a handguard, at 39 px to the inch, agrees.
The mount's plate: from the corner down its outer face to its lower edge0.798 in ± 0.042 in 20.3 mmCorroboratedPhoto: milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L
Photo 0.798 in ± 0.042 in used
milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L, harvested
Scale: the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing). Read by a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ±. The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the plate's outer face from the corner to its lower edge (20.3 mm)
Photo 0.784 in ± 0.04 in
Streamlight's gallery image _5: a handguard from its right side, the HL-X on its M-LOK mount, 800 x 800, harvested
Scale: the handguard's M-LOK slots: 61.2 px to the 40 mm pitch (std.mlok.slot_pitch), 38.9 px/in in the face's plane. Read by the plate's outer face from its top edge (row 302.5, under the lit band of the seat's lip tops) to its lower edge (row 333): 30.5 px
Four photos of the mount alone through fitted cameras; the maker's side view of it on a handguard agrees.
The mount's plate thickness (outer face to the face on the handguard)0.216 in ± 0.033 in 5.5 mmProvisionalPhoto: milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L
Photo 0.216 in ± 0.033 in used
milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L, harvested
Scale: the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing). Read by a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ±. The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the plate's thickness (5.5 mm), at its ends and its lower edge
The angle inside the mount between its plate and its seat135° ± 1°ConflictWorked out: What the mount has to fit, not a reading: the handguards' faces above a side row of M-LOK slots stand at 45 degrees to it (the octagons' faces 45 degrees apart: BCM's MCMR's mlok and mlok_between faces at 90 and 45, Geissele's MK16's at 90 and 45), and the seat's inner face lies over that face; at a smaller angle it stands into it.
Photo 129.5 deg ± 4 deg
milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L, harvested
Scale: the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing). Read by a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ±. The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the angle between the plate's outer face and the seat's lip tops, inside the L (129.5 degrees)
Worked out 135 deg ± 1 deg used
What the mount has to fit, not a reading: the handguards' faces above a side row of M-LOK slots stand at 45 degrees to it (the octagons' faces 45 degrees apart: BCM's MCMR's mlok and mlok_between faces at 90 and 45, Geissele's MK16's at 90 and 45), and the seat's inner face lies over that face; at a smaller angle it stands into it., harvested
Decided by what it has to fit (the mount is sold for M-LOK handguards, and Streamlight's own pictures have it on one over its top corner); the photos' figure, 1.4 of its ± away, stays beside it.
fit and fits differ by 5.5° beyond what each states it is good to.
Wider than a right angle: on a handguard's side face the seat rises toward the handguard from the plate's top edge, and the light on it leans out from upright by the angle less 90 degrees. In milgear's view from above (71643) the two legs' holes are both nearly round (0.84 and 0.81 of a circle as they show through), which two faces at a right angle can't both be; the inside view (71642) is too close to read an angle off by eye. 1lumen's reviewer (in the discovery's reading of a page the harvester was refused): "You can orient the M-LOK adapter to slant either way".
The mount's seat: from the corner across its lip tops to the far lip's outer edge0.689 in ± 0.046 in 17.5 mmProvisionalPhoto: milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L
Photo 0.689 in ± 0.046 in used
milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L, harvested
Scale: the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing). Read by a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ±. The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the seat's width over the lips (17.5 mm)
The seat's near lip (at the corner): its top's width0.22 in ± 0.033 in 5.6 mmProvisionalPhoto: milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L
Photo 0.22 in ± 0.033 in used
milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L, harvested
Scale: the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing). Read by a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ±. The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the near lip's top, the corner to its inner edge (5.6 mm)
The seat's far lip: its top's width0.11 in ± 0.029 in 2.8 mmProvisionalPhoto: milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L
Photo 0.11 in ± 0.029 in used
milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L, harvested
Scale: the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing). Read by a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ±. The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the far lip's top, its inner edge to the seat's far edge (2.8 mm)
The lips' height above the seat's floor (where the light's legs stand)0.064 in ± 0.03 in 1.6 mmProvisionalPhoto: milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L
Photo 0.064 in ± 0.03 in used
milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L, harvested
Scale: the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing). Read by a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ±. The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the floor below the lip tops (1.6 mm)
The seat's thickness, the lip tops to its inner face0.226 in ± 0.032 in 5.7 mmProvisionalPhoto: milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L
Photo 0.226 in ± 0.032 in used
milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L, harvested
Scale: the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing). Read by a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ±. The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the seat from its lip tops to its inner face (5.7 mm)
The plate's two screws (the T-nuts' middle line) below the corner0.417 in ± 0.031 in 10.6 mmCorroboratedPhoto: milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L
Photo 0.417 in ± 0.031 in used
milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L, harvested
Scale: the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing). Read by a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ±. The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the plate's holes' line, on its outer face, below the corner (10.6 mm)
Photo 0.424 in ± 0.04 in
Streamlight's gallery image _5: a handguard from its right side, the HL-X on its M-LOK mount, 800 x 800, harvested
Scale: the handguard's M-LOK slots: 61.2 px to the 40 mm pitch (std.mlok.slot_pitch), 38.9 px/in in the face's plane. Read by the plate's top edge (row 302.5) to its two screws' middles (row 319): 16.5 px
Four photos of the mount alone through fitted cameras; the maker's side view of it on a handguard agrees.
The plate's two screws (its T-nuts), centre to centre0.787 in ± 0.004 in 20 mmConfirmedWorked out: {std.mlok.interval}
Worked out 0.787 in ± 0.004 in used
{std.mlok.interval}, harvested
Photo 20.3 mm ± 0.7 mm
Streamlight's gallery image _5: a handguard from its right side, the light on its M-LOK mount, 800 x 800, harvested
Scale: the handguard's M-LOK slots: 61.2 px to the 40 mm pitch (std.mlok.slot_pitch). Read by the two screw heads' middles, columns 477 and 508: 31 px; one pixel is 0.65 mm
The standard's interval, which every two-nut M-LOK part on file is placed by; the maker's own side view of the mount reads it within a pixel.
Both in the one slot the plate is centred on, in every installed photo on file (the maker's side view, its _4 and two siblings' pictures): an accessory's two T-nuts stand the M-LOK interval apart, one in each half of a slot (data/interfaces.yaml).
The plate's screw holes (10-24 clearance), diameter0.215 in ± 0.008 in 5.5 mmProvisionalPhoto: milgear.fi 71643: the mount 88300 laid with the kit, both legs' outer faces toward the lens from above, 1400 x 979
Photo 0.215 in ± 0.008 in used
milgear.fi 71643: the mount 88300 laid with the kit, both legs' outer faces toward the lens from above, 1400 x 979, harvested
Scale: the plate's two holes, std.mlok.interval (20 mm) apart: 234.9 px, 11.745 px/mm across the plate (the seat's length, 446 px against the plate's 453, puts the seat 1.5% further off). Read by each hole's see-through width along the plate (the plate is turned about its length, so across it the far rim cuts the opening): 64.3 and 64.2 px
The plate's counterbores (for the 10-24 button heads), diameter at its outer face0.374 in ± 0.012 in 9.5 mmProvisionalPhoto: milgear.fi 71643: the mount 88300 laid with the kit, both legs' outer faces toward the lens from above, 1400 x 979
Photo 0.374 in ± 0.012 in used
milgear.fi 71643: the mount 88300 laid with the kit, both legs' outer faces toward the lens from above, 1400 x 979, harvested
Scale: the plate's two holes, std.mlok.interval (20 mm) apart: 234.9 px, 11.745 px/mm across the plate (the seat's length, 446 px against the plate's 453, puts the seat 1.5% further off). Read by each counterbore's rim along the plate, columns 427 to 537 and 662 to 775: 110 and 113 px
The plate's counterbores, depth from its outer face0.066 in ± 0.06 in 1.7 mmProvisionalPhoto: milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L
Photo 0.066 in ± 0.06 in used
milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L, harvested
Scale: the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing). Read by a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ±. The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the counterbores' floor below the outer face (1.7 mm), read only through where the holes' see-through middles fall: the weakest figure of the fit
The seat's two holes (8-32 clearance), diameter0.176 in ± 0.008 in 4.5 mmProvisionalPhoto: milgear.fi 71643: the mount 88300 laid with the kit, both legs' outer faces toward the lens from above, 1400 x 979
Photo 0.176 in ± 0.008 in used
milgear.fi 71643: the mount 88300 laid with the kit, both legs' outer faces toward the lens from above, 1400 x 979, harvested
Scale: the plate's two holes, std.mlok.interval (20 mm) apart: 234.9 px, 11.745 px/mm across the plate (the seat's length, 446 px against the plate's 453, puts the seat 1.5% further off). Read by each hole's see-through width along the seat: 51.6 and 51.8 px, at the seat's scale (1.5% under the plate's)
The seat's two holes (the light's two ports under its legs), centre to centre0.852 in ± 0.045 in 21.6 mmProvisionalPhoto: milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L
Photo 0.852 in ± 0.045 in used
milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L, harvested
Scale: the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing). Read by a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ±. The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the seat's holes' middles (21.7 mm); in the view from above alone, 254.7 px at the seat's scale, 22.0 mm
The light's legs' middles are 0.897 in apart by the bands they hang from (band_front_x, band_rear_x, band_length): each hole is inside its leg.
The seat's holes' line across the seat from the corner0.402 in ± 0.039 in 10.2 mmProvisionalPhoto: milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L
Photo 0.402 in ± 0.039 in used
milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L, harvested
Scale: the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing). Read by a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ±. The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the seat's holes' line from the corner along the lip tops (10.2 mm)
The middle of the floor between the lips is 0.401 in from the corner (mlok_near_lip_width, mlok_seat_width, mlok_far_lip_width): the holes, and the light's legs on them, are on it.
The seat's counterbores (for the 8-32 heads, on its inner face), diameter0.3 in ± 0.04 in 7.6 mmProvisionalPhoto: milgear.fi 71642: inside the mount's L, the plate's inner face up, 1400 x 980
Photo 0.3 in ± 0.04 in used
milgear.fi 71642: inside the mount's L, the plate's inner face up, 1400 x 980, harvested
Scale: the plate's two holes, std.mlok.interval (20 mm) apart: 368 px, 18.4 px/mm on the plate's inner face; the seat's face stands further off and is turned (no camera fitted to this view): the ± allows 10%. Read by the left counterbore's rim across its widest, columns 508 to 650
The seat's counterbores, depth from its inner face0.074 in ± 0.066 in 1.9 mmProvisionalPhoto: milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L
Photo 0.074 in ± 0.066 in used
milgear.fi's 71638, 71643, 71640, 71642: the mount 88300 alone on white, 1400 x 980; 71638 and 71640 three-quarter views of the plate's outer face and the seat's channel, 71643 from above with both legs' outer faces toward the lens, 71642 inside the L, harvested
Scale: the plate's two holes, std.mlok.interval (20 mm) apart: an M-LOK accessory's two T-nuts in one slot (the maker's side view of the light on its mount reads 20.3 mm: mlok_screw_spacing). Read by a pinhole camera for each photo and the mount's section fitted together (the mount is one section along its length: the plate, the seat standing from the plate's top edge at an angle to it, two lips along the seat and the floor between them; holes through each leg), to 57 points read on the four photos: corners at both ends, the plate's lower edge, the lips' edges, the inner corner, and the holes' see-through middles, taken at the middle of each hole's through part. rms 1.49 of the points' stated ±. The ± is twice the fit's own, wider than the spread of the four fits that each leave one photo out (the seat's angle 128.4 to 130.8 degrees, its width 17.2 to 18.2 mm): the counterbores' floor above the seat's inner face (1.9 mm), read only through where the holes' see-through middles fall
The plate's lugs (two crescents round each hole, on its inner face, that stand in the slot): their outer radius about the hole0.236 in ± 0.02 in 6 mmConfirmedWorked out: ({std.mlok.slot_length} - {std.mlok.interval}) / 2
Worked out 0.236 in ± 0.02 in used
({std.mlok.slot_length} - {std.mlok.interval}) / 2, harvested
What the slot leaves past each T-nut: two nuts the interval apart in a slot 32 mm long, the lugs about each reaching to the slot's end.
Photo 6.7 mm ± 0.7 mm
milgear.fi 71642: inside the mount's L, the plate's inner face up, 1400 x 980, harvested
Scale: the plate's two holes, std.mlok.interval (20 mm) apart: 368 px, 18.4 px/mm along the plate's inner face (no camera fitted to this view). Read by the two crescents about the left hole, outer edge to outer edge along the plate: 246 px
They stand in the slot and can reach no further than its ends; the inside view, read without a fitted camera, agrees within its ±.
Two crescents about each hole on the plate's inner face (milgear 71642, and the instructions' drawing), standing into the slot.
The plate's lugs: their inner radius about the hole0.157 in ± 0.02 in 4 mmProvisionalWorked out: An assumption for the drawing, not a reading: the crescents' inner edges stand clear of the hole by about their own width in the inside view (71642), which is too oblique to read it on.
Worked out 0.157 in ± 0.02 in used
An assumption for the drawing, not a reading: the crescents' inner edges stand clear of the hole by about their own width in the inside view (71642), which is too oblique to read it on., harvested
The plate's lugs: how far they stand off its inner face into the slot0.05 in ± 0.025 in 1.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows the lugs in profile; less than a handguard's wall, which they stand in.
Worked out 0.05 in ± 0.025 in used
An assumption for the drawing, not a reading: no view on file shows the lugs in profile; less than a handguard's wall, which they stand in., harvested
The 10-24 button heads: how far they stand proud of the plate's outer face0.05 in ± 0.03 in 1.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: the maker's studio picture (GRITR 923578, bcb203eebdd6) shows the domed heads standing out of their counterbores, from three-quarters; their height isn't read.
Worked out 0.05 in ± 0.03 in used
An assumption for the drawing, not a reading: the maker's studio picture (GRITR 923578, bcb203eebdd6) shows the domed heads standing out of their counterbores, from three-quarters; their height isn't read., harvested
The mount's edges' break (GRITR: "beveled ends and corners")0.02 in ± 0.01 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: GRITR's sentence says the ends and corners are bevelled; their size is in no view at a scale that reads it.
Worked out 0.02 in ± 0.01 in used
An assumption for the drawing, not a reading: GRITR's sentence says the ends and corners are bevelled; their size is in no view at a scale that reads it., harvested
On the M-LOK mount on a side face: the light's axis above the plate's screws (the slot's centre line)1.2 in ± 0.06 in 30.5 mmProvisionalWorked out: {.mlok_screw_below_corner} - {.mlok_seat_hole_from_corner} * cos({.mlok_seat_angle}) + ({.axis_above_mount} - {.mlok_lip_height}) * sin({.mlok_seat_angle})
Worked out 1.2 in ± 0.06 in used
{.mlok_screw_below_corner} - {.mlok_seat_hole_from_corner} * cos({.mlok_seat_angle}) + ({.axis_above_mount} - {.mlok_lip_height}) * sin({.mlok_seat_angle}), harvested
The screws below the plate's top edge, then across the seat to its holes' line and up from the floor by the legs, at the seat's angle.
Photo 1.144 in ± 0.04 in
Streamlight's gallery image _5: a handguard from its right side, the HL-X on its M-LOK mount, 800 x 800, harvested
Scale: the handguard's M-LOK slots: 61.2 px to the 40 mm pitch (std.mlok.slot_pitch), 38.9 px/in in the face's plane; the light stands 0.36 in nearer the lens than the face, which a long lens doesn't see. Read by the body's axis (row 274.5: the tube's edges at 257 and 292, 35 px, 0.90 in as the tube is 0.92) to the plate's two screws' middles (row 319): 44.5 px
What the model is drawn from; the maker's view, 2 px under it, stays beside it as the conflict.
A check of the mount's figures against the maker's own side view of the light on it. The view puts the light 0.06 in lower than the figures do (within the two ±): either the light's legs reach less far below its axis than the 1913 clamp's bolt puts them (axis_above_mount is the bolt's figure: on the clamp nothing shows the legs' feet), or the seat's figures are off within their ± (its thickness and angle move it most). The model draws the figures: the legs stand on the mount's floor as they are drawn on the clamp.
On the M-LOK mount: the light's axis out from the handguard's face0.433 in ± 0.05 in 11 mmProvisionalWorked out: {.mlok_plate_thickness} - {.mlok_seat_hole_from_corner} * sin({.mlok_seat_angle}) - ({.axis_above_mount} - {.mlok_lip_height}) * cos({.mlok_seat_angle})
Worked out 0.433 in ± 0.05 in used
{.mlok_plate_thickness} - {.mlok_seat_hole_from_corner} * sin({.mlok_seat_angle}) - ({.axis_above_mount} - {.mlok_lip_height}) * cos({.mlok_seat_angle}), harvested
The light stands over the face's top edge leaning out (mlok_seat_angle less 90 degrees): its axis this far out from the face the plate is on, its body 0.46 in round it.
The M-LOK mount's weight (the aluminium piece alone)0.67 oz ± 0.12 ozConflictWorked out: {.mlok_length} * ({.mlok_plate_height} * {.mlok_plate_thickness} + {.mlok_seat_width} * {.mlok_seat_thickness} - {.mlok_seat_thickness} * ({.mlok_plate_thickness} + {.mlok_seat_thickness} * cos({.mlok_seat_angle})) / sin({.mlok_seat_angle}) / 2 - {.mlok_plate_thickness} * ({.mlok_seat_thickness} * sin({.mlok_seat_angle}) + ({.mlok_plate_thickness} + {.mlok_seat_thickness} * cos({.mlok_seat_angle})) / sin({.mlok_seat_angle}) * cos({.mlok_seat_angle})) / 2 - ({.mlok_seat_width} - {.mlok_near_lip_width} - {.mlok_far_lip_width}) * {.mlok_lip_height}) * {std.density.aluminium}
Worked out 0.67 oz ± 0.12 oz used
{.mlok_length} * ({.mlok_plate_height} * {.mlok_plate_thickness} + {.mlok_seat_width} * {.mlok_seat_thickness} - {.mlok_seat_thickness} * ({.mlok_plate_thickness} + {.mlok_seat_thickness} * cos({.mlok_seat_angle})) / sin({.mlok_seat_angle}) / 2 - {.mlok_plate_thickness} * ({.mlok_seat_thickness} * sin({.mlok_seat_angle}) + ({.mlok_plate_thickness} + {.mlok_seat_thickness} * cos({.mlok_seat_angle})) / sin({.mlok_seat_angle}) * cos({.mlok_seat_angle})) / 2 - ({.mlok_seat_width} - {.mlok_near_lip_width} - {.mlok_far_lip_width}) * {.mlok_lip_height}) * {std.density.aluminium}, harvested
Worked out: the section's area (the plate and the seat, less where they overlap at the corner and less the floor between the lips) times the length, times aluminium's density (the alloy isn't named: Battery Junction "Primary Material Aluminum", GRITR "Made from heavy-duty aluminum"). The holes and lugs aren't taken off or added (about 8% less metal in the model): the ± is that and the section's own.
Published “Unit Dimensions Weight 1.28 oz (36 g)”
Battery Junction, Streamlight M-LOK Mount for the ProTac Rail Mount Series (88300), Specifications, a seller, read Oct 19, 2026 the page, harvested Oct 19, 2026
The package: the same page's "Shipping Weight 0.08 lb" is 36 g.
The piece's own metal; the seller's figure is the boxed package's (it equals the page's shipping weight).
metal and battery-junction differ by 0.6 oz beyond what each states it is good to.
No maker's figure. Battery Junction's "Weight 1.28 oz (36 g)" is the same 36 g its page gives as the shipping weight ("Shipping Weight 0.08 lb") and its markup as the variant's weight: the package as boxed (the mount, two 10-24 and two 8-32 screws, two T-nuts, three hex keys), kept beside the figure worked out. The build's weight is the light's published 6.4 oz on either mount (the part has one weight): on the M-LOK mount the light weighs that less its 1913 clamp (no figure published) and more this piece and its four screws and two nuts.
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Picatinny rail (MIL-STD-1913)
- Uppers
- Aero Precision M4E1 Enhanced Upper Receiver Stripped, Aero Precision M4E1 Threaded upper receiver, BCM M4 Upper Receiver Assembly (w/ Laser T-Markings), Expo Arms 7075 Stripped AR-15 Upper Receiver, Geissele Automatics Super Duty Stripped Upper Receiver, Nordic Components 22RB .22 LR upper, 16", Palmetto State Armory AR-15 Stripped Upper Receiver, Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12", Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16"
- Handguards
- Aero Precision AR15 10.3" R-ONE M-LOK handguard, Aero Precision AR15 12.7" R-ONE M-LOK handguard, Aero Precision AR15 15" Enhanced M-LOK Handguard, Gen 2, Aero Precision AR15 15" R-ONE M-LOK handguard, Aero Precision AR15 15" S-ONE M-LOK Handguard, Aero Precision AR15 16.6" R-ONE M-LOK handguard, Aero Precision AR15 7.3" R-ONE M-LOK handguard, Aero Precision AR15 9.3" R-ONE M-LOK handguard, BCM MCMR-10 (M-LOK® Compatible* Modular Rail), BCM MCMR-13 (M-LOK® Compatible* Modular Rail), BCM MCMR-15 (M-LOK® Compatible* Modular Rail), Expo Arms Free Float AR-15 Handguard - M-LOK - 15", Geissele Automatics 10.5" Super Modular Rail MK16 M-LOK, Geissele Automatics 13.5" Super Modular Rail MK16 M-LOK, Geissele Automatics 15" Super Modular Rail MK16 M-LOK, MAS Defense 12.62" NERO M-LOK FREE FLOAT, MAS Defense 15" NERO M-LOK FREE FLOAT, MAS Defense 9.87" NERO M-LOK FREE FLOAT, Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length), Midwest Industries Combat Rail One Piece Free Float Handguard, M-LOK™ (15")
- Frames
- Taurus TX22 Gen 2 frame
- Rail sections
- Magpul M-LOK® Aluminum Rail, 3 Slots, Magpul M-LOK® Aluminum Rail, 5 Slots, Magpul M-LOK® Aluminum Rail, 7 Slots, Magpul M-LOK® Aluminum Rail, 9 Slots, Magpul M-LOK® Polymer Rail, 11 Slots, Magpul M-LOK® Polymer Rail, 3 Slots, Magpul M-LOK® Polymer Rail, 5 Slots, Magpul M-LOK® Polymer Rail, 7 Slots, Magpul M-LOK® Polymer Rail, 9 Slots
M-LOK
- Uppers
- Nordic Components 22RB .22 LR upper, 16" (fit unchecked), Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12" (fit unchecked), Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16" (fit unchecked)
- Handguards
- Aero Precision AR15 10.3" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 12.7" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 15" Enhanced M-LOK Handguard, Gen 2 (fit unchecked), Aero Precision AR15 15" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 15" S-ONE M-LOK Handguard (fit unchecked), Aero Precision AR15 16.6" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 7.3" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 9.3" R-ONE M-LOK handguard (fit unchecked), BCM MCMR-10 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM MCMR-13 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM MCMR-15 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM PMCR (Polymer M-LOK® Compatible Rail)* Carbine Length-BLACK (fit unchecked), BCM PMCR (Polymer M-LOK® Compatible Rail)* Mid Length-BLACK (fit unchecked), Expo Arms Free Float AR-15 Handguard - M-LOK - 15" (fit unchecked), Geissele Automatics 10.5" Super Modular Rail MK16 M-LOK (fit unchecked), Geissele Automatics 13.5" Super Modular Rail MK16 M-LOK (fit unchecked), Geissele Automatics 15" Super Modular Rail MK16 M-LOK (fit unchecked), Magpul MOE SL® Hand Guard, Carbine-Length – AR15/M4 (fit unchecked), Magpul MOE SL® Hand Guard, Mid-Length – AR15/M4 (fit unchecked), Magpul MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4 (fit unchecked), Magpul MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4 (fit unchecked), MAS Defense 12.62" NERO M-LOK FREE FLOAT (fit unchecked), MAS Defense 15" NERO M-LOK FREE FLOAT (fit unchecked), MAS Defense 9.87" NERO M-LOK FREE FLOAT (fit unchecked), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine) (fit unchecked), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length) (fit unchecked), Midwest Industries Combat Rail One Piece Free Float Handguard, M-LOK™ (15") (fit unchecked)
- Adapter plates
- Magpul M-LOK Hand Stop MOE Adapter (fit unchecked)
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Primary Arms $119.99 Two CR123A cells (88066) Nov 17, 2026, in stock that day
- Sportsman's Warehouse $134.97 SL-B26 USB pack (88071) Nov 21, 2026, in stock that day
- Alexander's Store $140.99 Two CR123A cells (88066) Nov 18, 2026, in stock that day
- Sportsman's Warehouse $143.99 Two CR123A cells (88066) Nov 21, 2026, in stock that day
- Impact Guns $147.99 Two CR123A cells (88066) Nov 21, 2026, in stock that day
- GRITR Outdoors $148.43 Two CR123A cells (88066) Nov 21, 2026, in stock that day
- Mile High Shooting Accessories $182.99 SL-B26 USB pack (88071) Nov 21, 2026, in stock that day
- MidwayUSA $133.44 Two CR123A cells (88066) Nov 21, 2026, out of stock that day
- Rifle Supply $136.99 Two CR123A cells (88066) Nov 21, 2026, out of stock that day
- MidwayUSA $143.64 SL-B26 USB pack (88071) Nov 21, 2026, out of stock that day
- AR15Discounts $145.00 Two CR123A cells (88066) Nov 21, 2026, out of stock that day
- GRITR Outdoors $162.99 SL-B26 USB pack (88071) Nov 21, 2026, out of stock that day