Adapter plate
Magpul M-LOK Hand Stop MOE Adapter
The adapter plate of Magpul's M-LOK Hand Stop Kit (MAG608), sold only in that kit: for "Magpul polymer M-LOK hand guards or aluminum hand guards with wider, flatter profiles". The kit's hand stop and index panel bolt through it into the hand guard's slots, one at each end, with its moulded rail cover between them; it can be snapped shorter at two marked lines. Black, FDE, ODG, Stealth Gray.

- Weight
- 0.3 oz ± 0.05 oz Provisionalpublished: Wing Tactical, Magpul M-LOK Handstop Kit (MAG-608), Specifications (source of the figures unstated), a seller, read Oct 5, 2026
- Lowest price
- Sold in the Magpul M-LOK Hand Stop Kit, not by itself
- Colours
- Black, FDE, ODG, Stealth Gray
- Drawn as
- modelled
- Maker's page
- magpul.com
Added to “22RB .22 LR rifle”, a build on the start page, where the designer starts a new adapter plate.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Overall length (along the handguard)4.715 in ± 0.02 in 119.8 mmCorroboratedPhoto: Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom
Photo 4.715 in ± 0.02 in used
Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom, harvested
Scale: the plate's own four screw holes (the white seen through each, by intensity-weighted centroid: columns 419.19, 697.39, 1531.89, 1814.57) as 0, 20, 80 and 100 mm (std.mlok.interval, std.mlok.slot_pitch): a 1D projective map along the plate through the four by least squares, which leaves 1.0 px at each (13.83 px/mm at the rear pair, 14.05 at the front: the photo's perspective). Read by the plate's two ends at mid-level 150 on the land either side of each end's notch (columns 285.3 and 280.5 at the left, 1951.4 and 1954.0 at the right), mapped: 119.76 mm. ± covers the holes' own miss (the pairs' middles read 3.976 intervals apart here, not 4: 0.6%), the lens and the edge
Photo 4.69 in ± 0.02 in
Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end, harvested
Scale: the plate's four holes in this photo at 0, 20, 80 and 100 mm, through a pinhole camera fitted to the plate (f 3221 px, 19.1 in away, 42.4 degrees above the land; residuals 0.4 to 0.8 px on the edges, 1.7 px on the holes). Read by the land's two ends through that camera (4.656 in apart: the near one where the land gives way to the end face, the far one against the background) and the near end face's foot 0.017 in further out, taken the same at the far end
Photo 4.697 in ± 0.02 in
Wing Tactical, the ODG kit with its hardware, 1280 x 1280: the plate outer side up, from above and the other end, harvested
Scale: the plate's four holes in this photo at 0, 20, 80 and 100 mm, through a pinhole camera fitted to the plate (f 2699 px, 15.2 in away, 45.6 degrees above the land; residuals 0.3 to 0.7 px on the edges, 1.1 px on the holes). Read by the land's two ends through that camera (4.674 in apart) and the near end face's foot 0.012 in further out, taken the same at the far end
The view from above, where the outline is the plate's foot at both ends. The two oblique photos, each scaled by its own holes through its own camera, read 0.4 and 0.5% less; the land between its ends reads 4.669, 4.656 and 4.674 in the three.
Three M-LOK slot pitches (120 mm, 4.724 in) within every reading's ±: the plate is as long as the kit's three pieces in a row, which a retailer's staff put at "approximately 4.75 inches" (OpticsPlanet's Q&A, quoted in the hand stop's seed).
Thickness under what it carries (how far it stands them off the handguard's face)0.103 in ± 0.012 in 2.6 mmCorroboratedPhoto: Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end
Photo 0.103 in ± 0.012 in used
Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end, harvested
Scale: the camera fitted to the plate in this photo (its four holes at 0, 20, 80, 100 mm; the land 0.656 in wide and the plate 0.900 as the photo from above has them; f 3221 px, 42.4 degrees above the land). Read by the plate's near outline (its foot) below the land's near edge along each end section, 31 px down the columns against 93 px of land: through the camera, the foot 0.1025 in below the land (0.082 of it the bevel's drop, by the far side's band between the land and the far outline). The same within 0.001 with the principal point moved 100 px any way; 0.111 and 0.094 with the bevel 0.008 in narrower or wider in plan
Photo 0.096 in ± 0.012 in
Wing Tactical, the ODG kit with its hardware, 1280 x 1280: the plate outer side up, from above and the other end, harvested
Scale: the camera fitted to the plate in this photo (f 2699 px, 45.6 degrees above the land). Read by the same edges, the other specimen from the other end: the foot 0.0963 in below the land. Its lit end face, nearest the lens, is 9.5 to 10 px long past the land's end where 0.10 in of height and its 0.02 in run make 9.3
The larger photo, its edges the sharper (a black part on a pale ground); the two agree within 0.007 in.
The land's top above the end sections' underside: what the band between a hand stop's ears bears on, and the plate's whole thickness there. It is within its ± of that band's own depth (0.116 in on the hand stop's patent, 0.111 on the index panel's): the plate fills the space under the band, between the ears, that a flat face leaves empty. Magpul's drawing of the kit on the plate (072-0098-A, from the side and 15 degrees below) has the index panel's crown 0.238 to 0.245 in above the plate's underside, which is the panel's own height from its ears' tips (0.245 on its patent): there its ears' tips are level with the plate's underside. Read through fitted cameras from two photos, two specimens; not from a view square to the plate's side, of which there is none.
Width (side to side, at its widest: the moulded cover)1.036 in ± 0.012 in 26.3 mmProvisionalPhoto: Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom
Photo 1.036 in ± 0.012 in used
Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom, harvested
Scale: the plate's own four holes along it (length); across, the same scale at each station's depth (the square root of the along-scale's change: the end sections read one width at both ends by it, 0.8931 and 0.8934) over 0.992, the plate lying rolled a few degrees in the photo (its holes read 1.2% narrower across than along, its far bevel 41.5 px against the near one's 44). Read by the cover's outline across at 15 columns (363.6 px, sd 0.002 in). ± covers the roll (0.985 to 1.0) and the edge
The moulded cover between the two places. The index panel's plate is 1.038 in wide on its patent and the Type 2 cover 1.039: Magpul's image of the kit on the plate has their sides in one line. One photo: the two oblique photos fit these widths (their four long edges within 0.7 px) and cannot fix one themselves.
Width of the end sections (side to side, at the mounting face)0.9 in ± 0.012 in 22.9 mmProvisionalPhoto: Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom
Photo 0.9 in ± 0.012 in used
Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom, harvested
Scale: as for width. Read by the end sections' outline across at 16 columns each (315.0 and 317.7 px: 0.8931 and 0.8934 in at each end's own scale), over 0.992
Narrower than what it carries (1.04 to 1.05 in): a hand stop's ears overhang it by 0.07 in a side.
Width of the flat on each end section (what an accessory's band bears on)0.656 in ± 0.012 in 16.7 mmProvisionalPhoto: Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom
Photo 0.656 in ± 0.012 in used
Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom, harvested
Scale: as for width. Read by the two tone edges inside the outline along each end section (the land against the bevel either side of it: rows 1021.5 and 1252.5 at column 560, 1029.5 and 1259.5 at column 1670): 231 and 230 px
Each end section is a flat with a bevel down either side to the plate's edge. The flat is narrower than the band between a hand stop's ears (0.698 in on its patent; the index panel's 0.684): it lies between the ears, and the bevels (0.122 in across, falling 0.08 to 0.10: 35 degrees) run down under the ears' sloping insides (0.158 across, 0.116: 36 degrees).
Height of the end sections' edge (the bevel's foot above the mounting face)0.021 in ± 0.012 in 0.5 mmCorroboratedPhoto: Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end
Photo 0.021 in ± 0.012 in used
Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end, harvested
Scale: the camera fitted to the plate in this photo (height). Read by the far side's band (the far outline to the land's far edge, 6.2 and 5.0 px) gives the bevel's drop, 0.082 in; the near side's whole face gives 0.1025: the difference. A lighter strip 4 to 7 px high runs along the foot of the near face
Photo 0 in ± 0.012 in
Wing Tactical, the ODG kit with its hardware, 1280 x 1280: the plate outer side up, from above and the other end, harvested
Scale: the camera fitted to the plate in this photo (height). Read by the same difference: the bevel's drop 0.098 in of 0.096
The photo in which the strip along the foot shows; the other, half its size on the part, has the bevel run to the outline. Both say the edge is thin.
Land's end behind the plate's end (the end faces lean)0.023 in ± 0.008 in 0.6 mmCorroboratedPhoto: Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom
Photo 0.023 in ± 0.008 in used
Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom, harvested
Scale: the plate's own four holes (length). Read by the lighter ramp at each end of the outline, about 8 px, before the land's own tone
Photo 0.017 in ± 0.008 in
Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end, harvested
Scale: the camera fitted to the plate in this photo (height). Read by the near end face's foot beyond the land's end, along the plate
Photo 0.012 in ± 0.008 in
Wing Tactical, the ODG kit with its hardware, 1280 x 1280: the plate outer side up, from above and the other end, harvested
Scale: the camera fitted to the plate in this photo (height). Read by the near end face's foot beyond the land's end, along the plate
Seen from above, where the lean is the whole of what shows at each end; the other two are a pixel or two each.
M-LOK slots it covers3ProvisionalPhoto: Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom
Photo 3 count used
Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom, harvested
Scale: the plate's own four holes (length). Read by 119.8 mm of plate at the 40 mm slot pitch, its two places 19.9 mm from either end and two pitches apart: a place over the first slot it covers and one over the third, the moulded cover over the one between. Magpul's sheet draws it so on a Magpul hand guard (scenario 2, step 2: the stop's two T-nuts into one slot, the panel's into the next but one)
Places it has for what it carries2ConfirmedPublished: Magpul, MAG608 M-LOK Hand Stop Kit installation instructions (072-0098-A), scenario 2, step 1, the maker, read Oct 5, 2026
Published “Attach the M-LOK Hand Stop and Index Panel to the M-LOK Hand Stop MOE Adapter and insert the Screws through the bottom of the M-LOK Hand Stop and Index Panel.” used
Magpul, MAG608 M-LOK Hand Stop Kit installation instructions (072-0098-A), scenario 2, step 1, the maker, read Oct 5, 2026 the page, harvested Oct 5, 2026
One at each end, each a recess the shape of an M-LOK slot with two screw holes in its floor; the middle is a moulded cover ("The M-LOK Hand Stop MOE Adapter plate has an integral rail cover therefore the Type 2 Rail Cover is not used").
Distance between those places3.149 in ± 0.006 in 80 mmCorroboratedPhoto: Magpul, MAG608 installation instructions 072-0098-A, scenario 2 step 2: the kit on the plate over a Magpul hand guard, from the side and a little below; vector art, rendered at 4800 dpi
Photo 3.149 in ± 0.006 in used
Magpul, MAG608 installation instructions 072-0098-A, scenario 2 step 2: the kit on the plate over a Magpul hand guard, from the side and a little below; vector art, rendered at 4800 dpi, harvested
Scale: the plate's own pairs of screw holes in the drawing, by the seats that stand either side of each (matched pair to pair by correlation: 783.85 px at both ends, so the view is parallel), as the M-LOK interval (std.mlok.interval). Read by the pairs' middles 3134.5 px apart: 3.9988 intervals
Photo 3.142 in ± 0.012 in
Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end, harvested
Scale: the pairs' own spacing as the M-LOK interval, whatever the camera: the cross-ratio of the four holes' centres along their line (the white seen through each; on one line within 0.15 px). Read by cross-ratio 1.06700: the pairs' middles 3.9906 intervals apart. 0.3 px on one centre moves it 0.006 intervals
Photo 3.14 in ± 0.015 in
Wing Tactical, the ODG kit with its hardware, 1280 x 1280: the plate outer side up, from above and the other end, harvested
Scale: the cross-ratio of the four holes' centres, as above (the inner two 1.7 px off the outer two's line). Read by cross-ratio 1.06711: 3.9875 intervals
Photo 3.131 in ± 0.015 in
Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom, harvested
Scale: the cross-ratio of the four holes' centres, as above. Read by cross-ratio 1.06754: 3.9758 intervals. The holes' line is bowed 0.5 px the way a lens that stretches toward the frame's edge bows it, which reads this ratio low; the ± is for that, not for the centres (0.1 px)
Magpul's own drawing of the plate, made from its model and parallel: four intervals, which is two slot pitches (std.mlok.slot_pitch, 3.150 in), as the places must be to stand over the first and third of three slots. The three photos read 0.2 to 0.6% less, each with its own cause for it: a cross-ratio, which no lens keeps.
Two M-LOK slot pitches: each place stands over a slot's centre, with one slot between.
Rear place's centre ahead of the plate's rear end0.783 in ± 0.012 in 19.9 mmCorroboratedPhoto: Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom
Photo 0.783 in ± 0.012 in used
Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom, harvested
Scale: the plate's own four holes (length). Read by the middle of each pair of holes from its own end of the plate: 19.93 mm at one end, 19.84 at the other
Photo 0.769 in ± 0.015 in
Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end, harvested
Scale: the camera fitted to the plate in this photo (length). Read by the near pair's middle from the near end's foot
Photo 0.776 in ± 0.015 in
Wing Tactical, the ODG kit with its hardware, 1280 x 1280: the plate outer side up, from above and the other end, harvested
Scale: the camera fitted to the plate in this photo (length). Read by the near pair's middle from the near end's foot
The view from above, with both ends in it: the two ends read the same within 0.004 in, so the plate is the same end for end. The oblique photos read 0.007 and 0.014 less, as they read the length.
Half a slot pitch (0.787 in) within the ±: the plate's end is where the first slot's pitch begins. The same from either end: there is no front or rear to it but its lettering.
Reach inside the handguard (below the mounting face)No value yetMissingNo source yet
Not measured. Either side of each screw hole a crescent seat stands off the mounting side, fore and aft (Wing Tactical's photo of the FDE kit from its mounting sides; Magpul's drawings): they stand in the hand guard's slot, as a hand stop's own do. The screws and T-nuts are the carried accessories'.
Room under an accessory it carries (for its screws and T-nut)No value yetMissingNo source yet
No figure from Magpul. Each place's recess is 0.07 in deep in a 0.10 in plate (recess_depth): what stands off an accessory's band into a slot goes into it, and its screws go on through the floor into the hand guard's own slot.
Snap-off score's centre ahead of the plate's end (each end section's length)1.552 in ± 0.01 in 39.4 mmProvisionalPhoto: Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom
Photo 1.552 in ± 0.01 in used
Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom, harvested
Scale: the plate's own four holes (length). Read by the dark line across the plate between each end section and the cover (columns 826 to 833 and 1394 to 1402 on rows either side of the recess): its middle 39.53 mm from one end and 39.34 from the other
"The M-LOK Hand Stop MOE Adapter plate is customizable to length by snapping off sections at the marked locations" (072-0098-A): the two lines, one at each end of the cover. Each end section is as long as the hand stop's plate or the index panel's (1.56 to 1.575 in): an accessory covers it to the score.
Snap-off score's width0.02 in ± 0.006 in 0.5 mmProvisionalPhoto: Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom
Photo 0.02 in ± 0.006 in used
Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom, harvested
Scale: the plate's own four holes (length). Read by the dark line's width, 7 px at both
Moulded cover's crown above the mounting face0.24 in ± 0.02 in 6.1 mmProvisionalPhoto: Magpul, MAG608 installation instructions 072-0098-A, scenario 2 step 2: the kit on the plate over a Magpul hand guard, from the side and a little below; vector art, rendered at 4800 dpi
Photo 0.24 in ± 0.02 in used
Magpul, MAG608 installation instructions 072-0098-A, scenario 2 step 2: the kit on the plate over a Magpul hand guard, from the side and a little below; vector art, rendered at 4800 dpi, harvested
Scale: the plate's own pairs of holes in the drawing as the M-LOK interval (995.5 px/in along it); the view 15 degrees below level, by the plate's underside (0.900 in wide: 232 px between its near and far edges). Read by the cover's top line and the index panel's are one line within 2 px (rows 452 to 468 and 451 to 466): flush. The panel's upper outline is 280 px above the middle of the plate's underside: its crown 0.238 in above it, for the 0.245 in its patent gives from its ears' tips. ± covers the line's width and the angle
Flush with what it stands between: Magpul's image of the kit on the plate shows one surface from the hand stop over the cover to the index panel. In the two oblique photos this crown, with the two heights below, is within 3 px of the cover's outline through each fitted camera at the near side and within 8 at the far.
Moulded cover's height above the mounting face over the land's edge0.203 in ± 0.02 in 5.2 mmProvisionalPhoto: Magpul, MAG608 installation instructions 072-0098-A, scenario 2 step 2: the kit on the plate over a Magpul hand guard, from the side and a little below; vector art, rendered at 4800 dpi
Photo 0.203 in ± 0.02 in used
Magpul, MAG608 installation instructions 072-0098-A, scenario 2 step 2: the kit on the plate over a Magpul hand guard, from the side and a little below; vector art, rendered at 4800 dpi, harvested
Scale: as for cover_height. Read by seen from 15 degrees below, the cover's upper outline is its near shoulder, not its crown: 0.966 y + 0.259 z = 0.281 in at the point the view touches, which at z = half the land's width is this height. The index panel's plate, drawn flush with it, is 0.21 there on its patent
Moulded cover's height above the mounting face over the end sections' edge0.12 in ± 0.02 in 3 mmProvisionalPhoto: Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end
Photo 0.12 in ± 0.02 in used
Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end, harvested
Scale: the camera fitted to the plate in this photo (height). Read by the cover's far outline, 1 to 3 px above where a wing tip 0.046 in high at z = 0.513 would put it: 0.738 y + 0.674 z = 0.392 in where the view touches the far side, which at z = half the end sections' width is this height. Its near outline, 9 px below the end sections' own, is the wing tips at the mounting face's level (within 0.015 in) at the cover's full width; Wing Tactical's photo reads the same 9 px
Over the plate's edge the cover is still above the land; from there it turns down to its own edge at the mounting face's level, 0.068 in further out.
Moulded cover's end faces: how far they lean back from the land's level to the crown0.052 in ± 0.015 in 1.3 mmCorroboratedPhoto: Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end
Photo 0.052 in ± 0.015 in used
Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end, harvested
Scale: the camera fitted to the plate in this photo (height): 165 px/in along the plate there, and 52.5 px along it for each inch of height. Read by the dark band across the plate where the land meets the cover's near end (the score and the end face, in shade), on lines along the plate over the land's far half: 19 px. The score's 0.020 in and the crown's height above the land (cover_height less height) account for 10.5 of them; the rest is the face's lean
Photo 0.042 in ± 0.015 in
Wing Tactical, the ODG kit with its hardware, 1280 x 1280: the plate outer side up, from above and the other end, harvested
Scale: the camera fitted to the plate in this photo (height): 174 px/in along the plate there, 56.5 px per inch of height. Read by the same band at the cover's other end, 18.5 px, of which the score and the crown's height account for 11.2
The larger photo. Both rest on the crown's height, which is the drawing's; they are one reading of the lean from each end of the cover.
Magpul's drawing of the kit from the side shows the cover's ends sloped too. With it the cover's top stands clear of an accessory's end where its foot does not.
Moulded cover's corner radius in plan0.11 in ± 0.02 in 2.8 mmProvisionalPhoto: Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom
Photo 0.11 in ± 0.02 in used
Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom, harvested
Scale: the plate's own four holes (length). Read by the outline's step from the end sections' width to the cover's, an arc over 39 px along the plate at each of its four corners
Moulded cover's ribbed underside below the end sections' mounting faceNo value yetMissingNo source yet
Not measured. Under the cover the plate is a waffle of ribs (Wing Tactical's photo of its mounting side), and three sources have its rim standing below the end sections' underside: that photo (a step where an end section meets it), Magpul's drawing from the side (the lower outline bulges under the cover, about 0.03 in) and Magpul's low side view of the plate (a copy on file: the cover's lower edge 15 to 20 px below the end sections', where the two photos from 42 and 46 degrees have its wing tips level with them: something inboard of the tips, hidden from above). None is through a fitted camera. On a flat face it would touch before the ends do.
Recess at each place: length1.232 in ± 0.02 in 31.3 mmProvisionalPhoto: Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom
Photo 1.232 in ± 0.02 in used
Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom, harvested
Scale: the plate's own four holes (length). Read by the recess's two ends along the plate (columns 338 and 772 at the rear place, 1451 and 1892 at the front): 31.3 mm at both, centred on the pair of holes within 0.25 mm
An M-LOK slot's length (std.mlok.slot_length, 32 mm ± 1): each place is a slot's own shape cut into the land, for what stands off an accessory's band into a hand guard's slot.
Recess at each place: width0.279 in ± 0.01 in 7.1 mmProvisionalPhoto: Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom
Photo 0.279 in ± 0.01 in used
Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom, harvested
Scale: as for width. Read by the recess's two long edges (rows 1088 and 1184.5 to 1187 at the rear place): 98 px, 7.09 mm
An M-LOK slot's width (std.mlok.slot_width, 7 mm ± 0.5).
Recess at each place: depth below the land0.066 in ± 0.025 in 1.7 mmProvisionalPhoto: Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end
Photo 0.066 in ± 0.025 in used
Magpul, the kit's page, gallery _01 (black), 1200 x 1200: the plate alone beside the kit's row, from above and one end, harvested
Scale: the camera fitted to the plate in this photo (height). Read by the white seen through each hole is what its rim on the recess's floor and its rim on the mounting side leave between them, so its centre lies midway between the two levels: fitted 0.084 in below the land, with the mounting side 0.1025 below. Wing Tactical's photo fits 0.100, which is below its own plate: there the seats either side of each hole, in line with the lens, close the view, and the ± is for that
Screw holes' diameter0.224 in ± 0.004 in 5.7 mmProvisionalPhoto: Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom
Photo 0.224 in ± 0.004 in used
Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom, harvested
Scale: the plate's own four holes' spacing (length), at each pair's own scale. Read by each hole's width along the plate, by the second moment of the white seen through it: 78.5, 78.5, 79.9 and 80.7 px
The index panel's hole is 0.219 in on its patent: the kit's screws go through both.
Notch in each end: depth0.03 in ± 0.006 in 0.8 mmProvisionalPhoto: Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom
Photo 0.03 in ± 0.006 in used
Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom, harvested
Scale: the plate's own four holes (length). Read by the outline's step back in the middle of each end: 0.77 and 0.74 mm
Notch in each end: width0.3 in ± 0.02 in 7.6 mmProvisionalPhoto: Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom
Photo 0.3 in ± 0.02 in used
Primary Arms, MAG608-BLK_00.jpg, 2200 x 1466: the kit's pieces laid out, from above; the plate outer side up along the bottom, harvested
Scale: as for width. Read by the rows the step holds over, 1080 to 1190 with a row or two of corner at each: in line with the recess, and a little wider
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
M-LOK
- Uppers
- Nordic Components 22RB .22 LR upper, 16" (fit unchecked), Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12" (fit unchecked), Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16" (fit unchecked)
- Handguards
- Aero Precision AR15 10.3" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 12.7" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 15" Enhanced M-LOK Handguard, Gen 2 (fit unchecked), Aero Precision AR15 15" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 15" S-ONE M-LOK Handguard (fit unchecked), Aero Precision AR15 16.6" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 7.3" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 9.3" R-ONE M-LOK handguard (fit unchecked), BCM MCMR-10 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM MCMR-13 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM MCMR-15 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM PMCR (Polymer M-LOK® Compatible Rail)* Carbine Length-BLACK (fit unchecked), BCM PMCR (Polymer M-LOK® Compatible Rail)* Mid Length-BLACK (fit unchecked), Expo Arms Free Float AR-15 Handguard - M-LOK - 15" (fit unchecked), Geissele Automatics 10.5" Super Modular Rail MK16 M-LOK (fit unchecked), Geissele Automatics 13.5" Super Modular Rail MK16 M-LOK (fit unchecked), Geissele Automatics 15" Super Modular Rail MK16 M-LOK (fit unchecked), Magpul MOE SL® Hand Guard, Carbine-Length – AR15/M4 (fit unchecked), Magpul MOE SL® Hand Guard, Mid-Length – AR15/M4 (fit unchecked), Magpul MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4 (fit unchecked), Magpul MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4 (fit unchecked), MAS Defense 12.62" NERO M-LOK FREE FLOAT (fit unchecked), MAS Defense 15" NERO M-LOK FREE FLOAT (fit unchecked), MAS Defense 9.87" NERO M-LOK FREE FLOAT (fit unchecked), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine) (fit unchecked), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length) (fit unchecked), Midwest Industries Combat Rail One Piece Free Float Handguard, M-LOK™ (15") (fit unchecked)
M-LOK
- Hand stops
- BCM KAG (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK Hand Stop (fit unchecked), Magpul M-LOK Index Panel (fit unchecked)
- Vertical grips
- BCM Vertical Grip Mod 3 (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK MVG vertical grip (fit unchecked)
- Lights
- Cloud Defensive REIN (fit unchecked), Streamlight ProTac Rail Mount HL-X (fit unchecked), SureFire Mini Scout Light Pro (fit unchecked), SureFire Scout Light Pro Dual Fuel (fit unchecked)
- Rail sections
- Magpul M-LOK® Aluminum Rail, 3 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 5 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 7 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 9 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 11 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 3 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 5 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 7 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 9 Slots (fit unchecked)
- Sling mounts
- Magpul M-LOK QD Sling Mount (fit unchecked)
- Rail covers
- Magpul M-LOK Rail Cover Type 2 (fit unchecked)