Hand stop
BCM KAG (M-LOK® Compatible*)
BCM's Kinesthetic Angled Grip, made with Travis Haley: a short polymer grip that bolts into one M-LOK slot with two T-nuts. BCM: "Forward rake gives positive retention when using "C-clamp" (thumb over bore) method of handguard support", "Works as a rest for supported firing positions", "Small profile is just enough to get repeatable hand position on weapon forend", "Textured in front and back for positive engagement". Black and Flat Dark Earth. An angled grip and a hand stop, not a vertical grip: what a vertical grip makes of a pistol under the law is read of the vertical_grip kind, and this part isn't one.

- Weight
- 0.78 oz ± 0.2 oz Provisionalworked out: The model's polymer volume, 1.187 cubic inches (pipeline/blender/bcm_kag_mlok.py's manifest, body_volume_in3; the screws' heads apart), times std.density.polymer (18.68 g, 0.659 oz to the cubic inch): 22.0 g. The ± is a glass fill's, which no page rules out (up to 0.2 g/ml heavier: 0.14 oz), the width's ± 0.05 in (0.06 oz), and what the moulding is cored inside that no view shows (the model's only hollow is the face's). app/tests/bcm-kag-mlok.test.ts holds the model's volume to it.
- Lowest price
- $18.95 at BCM, read Nov 21, 2026 (Black)
- Maker's number
- BCM-KAG-MCMR-BLK
- Colours
- Black, Flat Dark Earth
- Drawn as
- modelled
- Maker's page
- bravocompanyusa.com
In “Two-tone 16 in, Stealth Gray and soft-shooting”, a build on the start page, in place of its Magpul M-LOK Hand Stop.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Overall length (the plate, along the handguard)2.73 in ± 0.03 in 69.3 mmCorroboratedPhoto: Rifle Supply 1858_EDIT-6, 3737 x 3737: a rifle's right side, square on, muzzle up, the KAG on the handguard's bottom face with its deep end toward the muzzle
Photo 2.73 in ± 0.03 in used
Rifle Supply 1858_EDIT-6, 3737 x 3737: a rifle's right side, square on, muzzle up, the KAG on the handguard's bottom face with its deep end toward the muzzle, harvested
Scale: the handguard's centre column of M-LOK slots beside it (std.mlok.slot_pitch, 40 mm): the column's luminance along y autocorrelated, 573.2 px a pitch over rows 1000 to 3600 and 580.8 over rows 2000 to 3650, 577 ± 4 px: 366.4 px/in. The slots' length over their pitch reads 0.81, the standard's 32 over 40. Read by the plate's ends along the handguard's bottom edge, columns 2010 to 2030 (just off the handguard's edge at 1995 to 2005), luminance under 150: rows 2482 to 3483, 1001 px. The ± covers the pitch's two readings (2.71 to 2.75) and the plate's ends' 3 px each; the plate lies 0.3 in nearer the lens's axis than the slots' face, under 1% at any lens a product shot is taken with
Photo 2.71 in ± 0.08 in
BCM's own BCM-KAG-MCMR-BLK-5, 1500 x 1000: the KAG on an MCMR's bottom M-LOK face, an oblique from below the rifle's right side, muzzle to the lower right, the deep end toward the receiver, harvested
Scale: the MCMR's lower row of M-LOK slots beside the plate, the standard's 40 mm pitch: three slots' starts along the handguard's axis 305 and 310 px apart on a 1.4x crop. Read by the plate's two ends where it meets the handguard, along the same axis: 530 px on the same crop (by eye on the crop, (190,128) to (640,408)); oblique and by eye, so a check on the reading above and not adopted
A square side view with the slots' pitch read by autocorrelation; BCM's own photo of it fitted is oblique and read by eye, and agrees within 0.02 in.
The mounting plate's two ends: the deep end's lip at the rear (the plate overhangs the deep end's back face) and the tail's tip. Two installed photos read it by their handguards' M-LOK slots; BCM's own side view of it alone, scaled by its two T-nuts as the M-LOK interval apart, would read 2.77 (893 px over the nuts' 254 px): that is the check below (nut_spacing), not a third reading.
Height (the mounting face to the deep end's toe)1.684 in ± 0.03 in 42.8 mmCorroboratedPhoto: Rifle Supply 1858_EDIT-6: the KAG fitted, the rifle's right side square on
Photo 1.684 in ± 0.03 in used
Rifle Supply 1858_EDIT-6: the KAG fitted, the rifle's right side square on, harvested
Scale: the same handguard's M-LOK slot pitch: 366.4 px/in (the length's rs6-slots). Read by the handguard's bottom edge, which the plate bears on (column 1995 to 2007 down the photo, 2000 at the toe's row), to the toe's furthest point (column 2617 at row 2862, the same at luminance 100, 128 and 160): 617 px
Photo 1.721 in ± 0.03 in
BCM's BCM-KAG-MCMR-BLK-2, 1499 x 1000: the KAG alone on white, its left side square on, its T-nuts up, harvested
Scale: the length (.length, 2.73 in) over the plate's 893 px at luminance under 128 (the side outline's): 327.1 px/in. Read by the side outline's height (tools/trace.py): the mounting face (row 225, the plate's top edge) to the toe's lowest row at luminance under 128; the toe's soft shadow on the white below reaches row 813 at 200, which isn't the part
Read square on, by the slots in the same photo; BCM's outline, at the scale the length gives it, has the toe 0.03 in further, within the two readings' ±.
From the face that bears on the handguard to the lowest point of the deep end's toe, square to the face.
Width (side to side, the plate)0.65 in ± 0.05 in 16.5 mmProvisionalPhoto: Rifle Supply 1858_EDIT-3, 2934 x 2934: the mounting face toward the lens, its two T-nuts standing on it, the deep end beyond the face's far edge
Photo 0.65 in ± 0.05 in used
Rifle Supply 1858_EDIT-3, 2934 x 2934: the mounting face toward the lens, its two T-nuts standing on it, the deep end beyond the face's far edge, harvested
Scale: its own two T-nuts' screws, taken as the M-LOK interval apart (std.mlok.interval, 20 mm), 279 px; the plate's length at .length gives 351 px/in, the same within 1%. Read by the face's two long edges across the tail's half (rows 1505 and 1732 at columns 1600 to 1900), 227 px. The photo is taken a little from one side (a band of the far wall shows beyond the face's far edge), so the face is foreshortened across: the ± takes up to 18 degrees of that, and the rounded edges
No view on file is square to the part's end or its face. The plate and the deep end are one width in the views from below (the toe's end face and the tail's underside, Rifle Supply 1858_EDIT-4); the model takes this for both.
M-LOK slots its lugs span1ProvisionalPhoto: BCM's BCM-KAG-MCMR-BLK-2: its left side square on, its T-nuts up
Photo 1 count used
BCM's BCM-KAG-MCMR-BLK-2: its left side square on, its T-nuts up, harvested
Scale: the length (.length) over the plate's 893 px. Read by the two nuts' centres 0.777 in apart (nut_spacing): both fit one slot of the standard's 1.26 in, at its interval
Its two T-nuts stand 0.77 in apart (nut_spacing): one in each half of a single 32 mm slot, as Magpul's hand stop's and MVG's do. BCM's page names no count.
Reach inside the handguard (below the mounting face, tightened)No value yetMissingNo source yet
Not sourced: BCM gives no T-nut figure. The nuts stand 0.15 in above the face in BCM's side view as shipped, turned and loose; tightened they draw up under the slot's lips.
Rear lug's centre ahead of the part's rear end0.767 in ± 0.02 in 19.5 mmProvisionalPhoto: BCM's BCM-KAG-MCMR-BLK-2: its left side square on, its T-nuts up
Photo 0.767 in ± 0.02 in used
BCM's BCM-KAG-MCMR-BLK-2: its left side square on, its T-nuts up, harvested
Scale: the length (.length, 2.73 in) over the plate's 893 px at luminance under 128, the side outline's frame: 327.1 px/in. Read by the rear nut's centre (column 939, the middle of its run of dark columns 867 to 1011 in rows 176 to 224) from the plate's rear end at that threshold (column 1190): 251 px
The rear T-nut's screw comes up through the deep end, from the big bore in its toe; the front one's through the tail, from the counterbore in its underside (Rifle Supply 1858_EDIT-4, from below; BCM's -4).
Its two T-nuts' centres, apart0.777 in ± 0.015 in 19.7 mmProvisionalPhoto: BCM's BCM-KAG-MCMR-BLK-2: its left side square on, its T-nuts up
Photo 0.777 in ± 0.015 in used
BCM's BCM-KAG-MCMR-BLK-2: its left side square on, its T-nuts up, harvested
Scale: the length (.length, 2.73 in) over the plate's 893 px: 327.1 px/in. Read by the two nuts' runs of dark columns in rows 176 to 224 (612 to 758 and 867 to 1011): their middles 685 and 939, 254 px apart
The check on the length: BCM's own side view, at the scale the installed photo's slots give the plate, puts its two nuts 0.777 in apart, which is the M-LOK interval (std.mlok.interval, 20 mm: 0.787) less 1.3%. The scale wasn't set by the nuts.
Mounting face: the rim round its hollow, wide0.1 in ± 0.02 in 2.5 mmProvisionalPhoto: Rifle Supply 1858_EDIT-3: the mounting face toward the lens
Photo 0.1 in ± 0.02 in used
Rifle Supply 1858_EDIT-3: the mounting face toward the lens, harvested
Scale: its two nuts as the M-LOK interval apart: 354 px/in along the part. Read by the rim at the tail's end and along the near long edge, 33 to 38 px, by eye on a full-size crop
The face that bears on the handguard is a rim round a hollow (Rifle Supply 1858_EDIT-3, BCM's FDE -4): the nuts' posts and the moulded words stand in the hollow.
Mounting face: the hollow's depth0.06 in ± 0.03 in 1.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows the hollow in section. Under the plate's 0.11 in at the tail's tip (the side outline), and the floor is seen well below the rim in the face-on photos.
Worked out 0.06 in ± 0.03 in used
An assumption for the drawing, not a reading: no view on file shows the hollow in section. Under the plate's 0.11 in at the tail's tip (the side outline), and the floor is seen well below the rim in the face-on photos., harvested
The deep end's side panel (the BCM mark's cup), deep0.05 in ± 0.03 in 1.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: the cup on each side of the deep end is seen in every side photo, and its depth in none square to it.
Worked out 0.05 in ± 0.03 in used
An assumption for the drawing, not a reading: the cup on each side of the deep end is seen in every side photo, and its depth in none square to it., harvested
The deep end's side panel: the rim round it, wide0.1 in ± 0.02 in 2.5 mmProvisionalPhoto: BCM's BCM-KAG-MCMR-BLK-2: its left side square on
Photo 0.1 in ± 0.02 in used
BCM's BCM-KAG-MCMR-BLK-2: its left side square on, harvested
Scale: 327.1 px/in (the length over the plate's 893 px). Read by the rim between the deep end's outline and its cup, 30 to 36 px on the cup's back and toe, by eye on the photo
The deep end's side panel: its top edge below the mounting face0.4 in ± 0.03 in 10.2 mmProvisionalPhoto: BCM's BCM-KAG-MCMR-BLK-2: its left side square on
Photo 0.4 in ± 0.03 in used
BCM's BCM-KAG-MCMR-BLK-2: its left side square on, harvested
Scale: 327.1 px/in. Read by the cup's top edge (row 355 to 360 on the photo) below the face (row 224), by eye
The deep end's side panel: its front edge at the top, ahead of the part's rear end0.96 in ± 0.03 in 24.4 mmProvisionalPhoto: BCM's BCM-KAG-MCMR-BLK-2: its left side square on
Photo 0.96 in ± 0.03 in used
BCM's BCM-KAG-MCMR-BLK-2: its left side square on, harvested
Scale: 327.1 px/in. Read by the cup's upper front corner, column 880 to 885 (the plate's rear end at 1194), by eye; below it the cup's front edge runs down to the deep end's front face and follows it a rim's width in
The bore in the deep end's toe (to the rear nut's screw), across0.42 in ± 0.05 in 10.7 mmProvisionalPhoto: Rifle Supply 1858_EDIT-4: the toe's end face toward the lens, the tail's underside beside it
Photo 0.42 in ± 0.05 in used
Rifle Supply 1858_EDIT-4: the toe's end face toward the lens, the tail's underside beside it, harvested
Scale: the toe's end face across, as the width (.width, 0.65 in): 240 px on a full-size crop. Read by the bore's rim across the same face, 155 px
The bore in the deep end's toe: how far in the screw's head stands0.75 in ± 0.2 in 19 mmProvisionalWorked out: An assumption for the drawing, not a reading: the rear screw's head is seen well down the bore from the toe (Rifle Supply 1858_EDIT-4, BCM's -4); how far isn't seen. Its screw reaches the nut above the plate.
Worked out 0.75 in ± 0.2 in used
An assumption for the drawing, not a reading: the rear screw's head is seen well down the bore from the toe (Rifle Supply 1858_EDIT-4, BCM's -4); how far isn't seen. Its screw reaches the nut above the plate., harvested
The counterbore in the tail's underside (the front nut's screw), across0.34 in ± 0.04 in 8.6 mmProvisionalPhoto: Rifle Supply 1858_EDIT-4: the tail's underside beside the toe
Photo 0.34 in ± 0.04 in used
Rifle Supply 1858_EDIT-4: the tail's underside beside the toe, harvested
Scale: the tail's underside across, as the width (.width, 0.65 in): 220 px on a full-size crop. Read by the counterbore's rim across the underside, 115 px
The screws' heads, across0.25 in ± 0.04 in 6.3 mmProvisionalPhoto: Rifle Supply 1858_EDIT-4: the front screw's head in its counterbore
Photo 0.25 in ± 0.04 in used
Rifle Supply 1858_EDIT-4: the front screw's head in its counterbore, harvested
Scale: the counterbore (.tail_counterbore, 0.34 in): 115 px. Read by the black head inside it, 85 px across, a socket head with a hex
The plate's corners in plan, rounded to0.08 in ± 0.02 in 2 mmProvisionalPhoto: Rifle Supply 1858_EDIT-3: the mounting face toward the lens
Photo 0.08 in ± 0.02 in used
Rifle Supply 1858_EDIT-3: the mounting face toward the lens, harvested
Scale: its two nuts as the M-LOK interval apart: 354 px/in along the part. Read by the face's four corners, each a quarter round of 25 to 30 px, by eye on a full-size crop
The ribs across the tail's underside and the deep end's front and back: their pitch along the surface0.061 in ± 0.003 in 1.5 mmProvisionalPhoto: BCM's BCM-KAG-MCMR-BLK-2: its left side square on
Photo 0.061 in ± 0.003 in used
BCM's BCM-KAG-MCMR-BLK-2: its left side square on, harvested
Scale: 327.1 px/in (the length over the plate's 893 px, the side outline's frame). Read by the back face's straight run, rows 381 to 558: the silhouette's rightmost column per row dips at each gap between two ribs, ten spacings of 19 to 20 px (20.0 px median); the deep end's front face reads 18 to 19 px per row on a face that leans, the same along it
BCM: "Textured in front and back for positive engagement". The ribs run across the part (Rifle Supply 1858_EDIT-4, from below) and through its sides: BCM's side view shows them in its silhouette as teeth, along the tail's underside from the tip, down the deep end's front face, and on its back face.
The ribs: the gap between two, along the surface0.022 in ± 0.006 in 0.6 mmProvisionalPhoto: BCM's BCM-KAG-MCMR-BLK-2: its left side square on
Photo 0.022 in ± 0.006 in used
BCM's BCM-KAG-MCMR-BLK-2: its left side square on, harvested
Scale: 327.1 px/in. Read by the gaps' widths on the back face's straight run, 6 to 8 px (median 7) of the 20 px pitch: the ribs are the wider
The ribs: how far they stand off the surface between them0.025 in ± 0.008 in 0.6 mmProvisionalPhoto: BCM's BCM-KAG-MCMR-BLK-2: its left side square on
Photo 0.025 in ± 0.008 in used
BCM's BCM-KAG-MCMR-BLK-2: its left side square on, harvested
Scale: 327.1 px/in. Read by the back face's silhouette, the ribs' tips at column 1115 and the gaps' floors at 1105 to 1108, 8 px; the tail's underside shows the same teeth in profile, smaller as the photo sees them along a slope
The front run of ribs (the tail's underside and the deep end's front face): its first rib at the tail's tip, ahead of the rear end2.69 in ± 0.02 in 68.3 mmProvisionalPhoto: BCM's BCM-KAG-MCMR-BLK-2: its left side square on
Photo 2.69 in ± 0.02 in used
BCM's BCM-KAG-MCMR-BLK-2: its left side square on, harvested
Scale: 327.1 px/in. Read by the first tooth under the tip, column 310 (the plate's rear end at 1190), by eye on a 2x enlargement
The front run of ribs: its last rib on the deep end's front face, below the mounting face1.315 in ± 0.03 in 33.4 mmProvisionalPhoto: BCM's BCM-KAG-MCMR-BLK-2: its left side square on
Photo 1.315 in ± 0.03 in used
BCM's BCM-KAG-MCMR-BLK-2: its left side square on, harvested
Scale: 327.1 px/in. Read by the last tooth down the deep end's front face, row 655 (the face at 225), by eye on a 2x enlargement; below it the toe is smooth
The back run of ribs (the deep end's back face): its first rib below the mounting face0.159 in ± 0.02 in 4 mmProvisionalPhoto: BCM's BCM-KAG-MCMR-BLK-2: its left side square on
Photo 0.159 in ± 0.02 in used
BCM's BCM-KAG-MCMR-BLK-2: its left side square on, harvested
Scale: 327.1 px/in. Read by the first tooth where the back face leaves the plate's rear corner, row 277, by eye on a 2x enlargement
The back run of ribs: its last rib below the mounting face1.058 in ± 0.02 in 26.9 mmProvisionalPhoto: BCM's BCM-KAG-MCMR-BLK-2: its left side square on
Photo 1.058 in ± 0.02 in used
BCM's BCM-KAG-MCMR-BLK-2: its left side square on, harvested
Scale: 327.1 px/in. Read by the last tooth down the back face, row 571, by eye on a 2x enlargement; below it the back face is smooth into the toe
The back run of ribs: how many16ProvisionalPhoto: BCM's BCM-KAG-MCMR-BLK-2: its left side square on
Photo 16 count used
BCM's BCM-KAG-MCMR-BLK-2: its left side square on, harvested
Scale: none: a count. Read by the teeth in the silhouette of the back face, rows 277 to 568, counted on a 1.6x enlargement (each 20 px apart on the straight run)
Counted on BCM's side view: thirteen down the straight back face at the 0.061 in pitch and three on the curve from the plate's rear corner, where they stand a little wider apart. The front run (the tail's underside and the deep end's front face) is counted by the model from its length over the pitch, 38; counted by eye on the same enlargement, 17 ahead of the front screw's head, about 7 beside and under it and 15 down the front face, 39 ± 2.
The front screw's head: how far it stands proud of the ribs' tips on the tail's underside0.02 in ± 0.008 in 0.5 mmProvisionalPhoto: BCM's BCM-KAG-MCMR-BLK-2: its left side square on
Photo 0.02 in ± 0.008 in used
BCM's BCM-KAG-MCMR-BLK-2: its left side square on, harvested
Scale: 327.1 px/in. Read by the silhouette's lowest row per column under the ramp (cols 640 to 725) against the ramp's line drawn straight from column 620 (row 373) to 730 (row 433): 3 to 7 px beyond it
BCM's side view shows a low bump under the ramp between columns 640 and 725 (x 1.42 to 1.68), centred at the front nut's x: the screw's black head, not the moulding's shape. It stands out of the ramp's line, which runs straight past it either side, by up to 7 px.
The edges' round0.03 in ± 0.015 in 0.8 mmProvisionalWorked out: An assumption for the drawing, not a reading: the moulding's edges are rounded in every photo, their radius read in none.
Worked out 0.03 in ± 0.015 in used
An assumption for the drawing, not a reading: the moulding's edges are rounded in every photo, their radius read in none., harvested
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
M-LOK
- Uppers
- Nordic Components 22RB .22 LR upper, 16" (fit unchecked), Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12" (fit unchecked), Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16" (fit unchecked)
- Handguards
- Aero Precision AR15 10.3" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 12.7" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 15" Enhanced M-LOK Handguard, Gen 2 (fit unchecked), Aero Precision AR15 15" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 15" S-ONE M-LOK Handguard (fit unchecked), Aero Precision AR15 16.6" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 7.3" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 9.3" R-ONE M-LOK handguard (fit unchecked), BCM MCMR-10 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM MCMR-13 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM MCMR-15 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM PMCR (Polymer M-LOK® Compatible Rail)* Carbine Length-BLACK (fit unchecked), BCM PMCR (Polymer M-LOK® Compatible Rail)* Mid Length-BLACK (fit unchecked), Expo Arms Free Float AR-15 Handguard - M-LOK - 15" (fit unchecked), Geissele Automatics 10.5" Super Modular Rail MK16 M-LOK (fit unchecked), Geissele Automatics 13.5" Super Modular Rail MK16 M-LOK (fit unchecked), Geissele Automatics 15" Super Modular Rail MK16 M-LOK (fit unchecked), Magpul MOE SL® Hand Guard, Carbine-Length – AR15/M4 (fit unchecked), Magpul MOE SL® Hand Guard, Mid-Length – AR15/M4 (fit unchecked), Magpul MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4 (fit unchecked), Magpul MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4 (fit unchecked), MAS Defense 12.62" NERO M-LOK FREE FLOAT (fit unchecked), MAS Defense 15" NERO M-LOK FREE FLOAT (fit unchecked), MAS Defense 9.87" NERO M-LOK FREE FLOAT (fit unchecked), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine) (fit unchecked), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length) (fit unchecked), Midwest Industries Combat Rail One Piece Free Float Handguard, M-LOK™ (15") (fit unchecked)
- Adapter plates
- Magpul M-LOK Hand Stop MOE Adapter (fit unchecked)
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- BCM $18.95 Black Nov 21, 2026, in stock that day
- BCM $18.95 Flat Dark Earth Nov 21, 2026, in stock that day
- Primary Arms $18.95 Black Nov 21, 2026, in stock that day
- KYGUNCO $18.95 Black Nov 21, 2026, in stock that day
- Right To Bear $21.00 Black Nov 21, 2026, in stock that day
- Rifle Supply $21.99 Black Nov 21, 2026, in stock that day
- Sportsman's Warehouse $19.99 Black Nov 21, 2026, out of stock that day