Upper
Nordic Components 22RB .22 LR upper, 16"
Dedicated .22 LR upper with a 16" stainless barrel threaded 1/2-28, slick-side receiver, full-length top rail and a receiver-height M-LOK handguard. Black Teflon finish. Ships with a thread protector (the muzzle slot's nordic-thread-protector) and a 10-round Black Dog magazine.

- Weight
- 60.6 oz Confirmedmeasured: measured on the part, Oct 5, 2026, the user's scale (not named), their own upper on it, as asked for on 2026-10-02 ("the upper alone on it, no magazine": docs/STATUS.md, the photo list's 7)Its sources span 59.5 oz to 60.62 oz.
- Lowest price
- $549.00 at Aerospace Arms, read Nov 21, 2026
- Made for
- Nordic Components' 22RB Dedicated 22 Upper converts your AR15-pattern rifle into a dedicated 22 rimfire just by changing upper receivers. (the page's category: NC 22LR UPPERS & CHARGE HANDLES > 22RB (Dedicated .22 Upper))
- Maker's number
- 22RB-UPPER-16-KIT
- Colour
- Black (placeholder)
- Drawn as
- modelled
In “22RB .22 LR rifle”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Barrel length16 in 406.4 mmConfirmedPublished: Nordic Components, the maker
Published 16 in used
Nordic Components, the maker the page, from the project brief
Pin-hole spacing as read in the upper's reference photo6.375 in 161.9 mmConflictWorked out: {std.ar15.pin_spacing}
Worked out 6.375 in used
{std.ar15.pin_spacing}, from the project brief
Photo 6.295 in
not yet archived, from the project brief
Scale: not recorded in brief. Read by calibrated photo measurement
Reads 1.25% short, so that photo's scale is off near the pins.
The pins are a standard interface. Features from this photo are aligned to the lower at the pin midpoint rather than trusting its scale there.
std and photo differ by 0.08 in beyond what each states it is good to.
Bore axis above pin centerline0.877 in ± 0.0015 in 22.3 mmConfirmedWorked out: {std.ar15.bore_axis_y}
Worked out 0.8775 in used
{std.ar15.bore_axis_y}, from the site owner
The standard's height: the upper's lugs fix its bore over the pins (drawing 8448524: .625 above its underside, the lug holes .251 below), in line with the receiver extension. Not measured on this upper. M2 had 0.849, the lower's photo-read axis (M6).
Top rail surface above pin centerline2.09 in ± 0.015 in 53.1 mmConflictPhoto: the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03
Photo “about 2.03 in”
not yet archived, from the project brief
Scale: not recorded in brief. Read by calibrated photo measurement
Photo 2.07 in ± 0.04 in
complete rifle lying flat on its right side, photographed straight down; supplied in chat, from the site owner
Scale: pin frame: takedown, pivot, trigger pin and selector (Hough-refined), 49.18 px/in, rotation 1.43°, rms 0.03 in. Read by top silhouette of the receiver's rail just ahead of the charging handle (x 0–0.3 in, 2.07–2.08), neutral-colour mask; true side view, so no elevation inflation
Farther forward, on the handguard, the rail's top edge reads a median 2.17 (slot tops and bottoms averaged). That's 12–20 in from the pins, where lens distortion and a 0.15° rotation uncertainty add up to ~0.05 in, so the receiver reading is used.
Photo 2.09 in ± 0.015 in used
the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03, from the site owner
Scale: the rail's 49 slots, found at mid-depth of the teeth (a projective fit to their centres: 0.3 to 0.6 px rms, 106 to 120 px/in), and the two lug holes' see-through centres, all on the centre plane; a camera pose fitted to them. Checks: the lug holes read 6.383 apart directly (+0.13%), the handguard's M-LOK slits 1.573 to 1.582 apart (40 mm), the receiver's underside 0.24 to 0.25 above the pins (the deck's 0.254). Read by the teeth's tops above the pin line in the two photos taken square on (the lens 0.5 in from the bore's line): 2.088 and 2.093, 0.011 taken off for the rail's near edge
The user's own upper in two photos taken square on, the pins and the rail in one pose (2.088, 2.093). The flat-lay's 2.07 ± 0.04 agrees; the brief's 2.03 doesn't.
photo and user differ by 0.06 in beyond what each states it is good to.
Upper receiver height including rail1.817 in ± 0.058 in 46.2 mmCorroboratedPhoto: right side, Nordic NC22-16-Upper-V2, 1200 px
Photo 1.77 in
not yet archived, from the project brief
Scale: not recorded in brief. Read by calibrated photo measurement
Photo 1.817 in ± 0.058 in used
right side, Nordic NC22-16-Upper-V2, 1200 px, harvested
Scale: rail model 02-24d592636074.calib.json along the rail (tilt 0.37° removed) and its local scale across it, anchored at the takedown lug. Read by rail tooth tops to the receiver's underside, medians over x 1–5.5 (between the lugs), from the traced outline (tools/trace.py target)
Photo on file, traced; the brief's 1.77 (photo not archived) agrees within the ±.
The right-side product photo (24d592636074) isn't elevated at the receiver (its underside lands on the lower's deck); the left one (2b348f6a5149) reads high.
Handguard height2.006 in ± 0.045 in 50.9 mmConflictWorked out: {.handguard_rail_top_above_pin} - {.handguard_bottom_y}
Photo 1.91 in
not yet archived, from the project brief
Scale: not recorded in brief. Read by calibrated photo measurement
Photo 2.039 in ± 0.062 in
complete rifle lying flat on its right side, photographed straight down; supplied in chat, from the site owner
Scale: pin frame: takedown, pivot, trigger pin and selector (Hough-refined), 49.2 px/in. Read by rail tooth tops (the top edge's max over 0.4 in windows) to the handguard's underside, medians over x 11–18.5 (clear of the scope's rings), from the traced outline (tools/trace.py target); segmentation: saturation < 0.35 and value < 0.5, or value < 0.2 (the black handguard reflects the wood); ± includes the lens's ~1.2% compression across the axis there, left uncorrected
Replaces the M2 reading of 1.85, whose mask lost the handguard's reflective upper half.
Photo 2.038 in ± 0.058 in
right side, Nordic NC22-16-Upper-V2, 1200 px, harvested
Scale: rail model 02-24d592636074.calib.json along the rail (tilt 0.37° removed) and its local scale across it, anchored at the takedown lug. Read by rail tooth tops to the handguard's underside, medians over x 9–18.5, from the traced outline (tools/trace.py target). The receiver in the same photo lands on the lower's deck (0.240 vs 0.254) and on the rail top (2.058 vs 2.07), so the view isn't elevated
Photo 1.971 in ± 0.016 in
Aawee: the NCT3 handguard, straight end-on, transparent background, harvested
Scale: nordic-22rb-upper.handguard_width (1.602 in, the listed 40.7 mm across the side flats) over the outline's 321 px extent, 200.4 px/in. Read by the traced end section's height, bottom flat to rail top (profiles.front, tools/trace.py's check); ± is a pixel at each end and the width's. The rail's end may sit a little behind the near face and read slightly small
Recorded as a check on the outline since M5 ("1.98 from its end view"); a measurement of the height in its own right, and the only one that isn't a side photo's.
Worked out 2.0059 in ± 0.045 in used
{.handguard_rail_top_above_pin} - {.handguard_bottom_y}, harvested
What is drawn: the handguard's own rail top over its underside, the underside half the width below the barrel's axis.
Photo 2.02 in ± 0.02 in
the user's own 22RB lying on a tile floor, left and right side, square on from 5 to 7 ft, zoomed; 2026-10-03); a copy on file (the user's own 22RB, the muzzle end straight on, the rail at the bottom, a tape across above; 2026-10-03, from the site owner
Scale: the rail's 49 slots and the two lug holes' see-through centres, all on the centre plane, in one fitted camera pose (rail_slot0_x#user); in the end views, the rail head's 0.835. Read by the bottom flat to the teeth's tops: 2.01 and 2.02 in the two side photos taken square on (the underside 0.063 to 0.083 above the pins, the tops 2.088 and 2.093); 2.02 to 2.03 end on
The height the handguard has where it is drawn, centred on the barrel under its own rail; the end view reads the same (1.971 ± 0.016). The two side photos read 2.04, within their ± 0.06 of it: their undersides are where this puts them (0.088 in the right photo's frame) and their rail tops along the handguard read 0.05 high (2.124 against 2.07), the trend a lens gives (handguard_rail_step). The brief's 1.91 (photo not archived) stays visible.
photo and flatlay differ by 0.129 in beyond what each states it is good to.
photo and right-photo differ by 0.128 in beyond what each states it is good to.
photo and end-view differ by 0.061 in beyond what each states it is good to.
photo and on-axis differ by 0.096 in beyond what each states it is good to.
photo and user differ by 0.11 in beyond what each states it is good to.
end-view and user differ by 0.049 in beyond what each states it is good to.
Rail tooth tops to the handguard's underside. M2 read 1.85 from the flat-lay with a mask (saturation < 0.35 and value < 0.5) that lost the black handguard's upper half where it reflects the wood; re-traced in M3 (tools/trace.py), the flat-lay and the product's right-side photo agree on 2.04. The left product photo reads high (2.10: its receiver sits 0.18 below the lower's deck, so its heights aren't used).
Muzzle thread shoulder ahead of the takedown pin (where a muzzle device seats)21.134 in ± 0.03 in 536.8 mmProvisionalWorked out: {.muzzle_ahead_of_pin} - {nordic-thread-protector.length}
Worked out 21.134 in used
{.muzzle_ahead_of_pin} - {nordic-thread-protector.length}, harvested
The photos show the upper as shipped, its thread protector on: the shoulder is the protector's seam with the barrel, so it is the protector's face less the protector's length. A suppressor or flash hider seats here.
Muzzle face, behind the thread protector's front face0.005 in ± 0.01 in 0.1 mmProvisionalPhoto: Nordic: the 22RB's muzzle end, three-quarter view, 1200 px
Photo 0.005 in ± 0.01 in used
Nordic: the 22RB's muzzle end, three-quarter view, 1200 px, harvested
Scale: the protector's front face, 157 px across its long axis, taken as nordic-thread-protector.od (0.717): 218.5 px/in. The bore's ellipse (short axis 0.42 of the long) puts the view 65 degrees off the bore axis. Read by the crop stretched along the ellipses' short axis, so circles about the bore axis are circles again with their centres displaced by depth (0.002 in of depth a pixel). The protector's mouth and the outer edge of the barrel's end face, read off radial profiles and off the stretched picture, have centres 0.5 px and 4 px apart: flush, to 0.009 in inside. An automatic edge tracker jumped between the rings and wasn't used (a copy on file). ± covers the two readings
The protector is a threaded sleeve, open at both ends (Nordic's photo of it alone, 9056e2073f45): what shows in its mouth on the rifle is the barrel's own end face and crown.
Muzzle thread: the shoulder to the muzzle face0.506 in ± 0.012 in 12.9 mmConflictPhoto: the user's own 22RB, the bare muzzle from the side, the thread protector off; 2026-10-03
Photo 0.465 in ± 0.022 in
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: the protector's length as that photo has it (nordic-thread-protector.length#left, 0.47 ± 0.02). Read by the protector's length less the muzzle face's setback in its mouth (muzzle_face_behind_protector, 0.005)
The protector seats on the shoulder (its seam with the barrel) and the muzzle face is flush with its front or just inside. Until 2026-10-03 this was the adopted figure, derived from the protector's length; with the bare thread measured the dependence runs the other way (nordic-thread-protector.length#thread).
Published “The length of of the barrel before it widens to the larger OD, is roughly 0.48" long.”
Northeast Shooters forum, 'Nordic NC22 .22lr AR Review', post 15 (2020-10-12): an owner of Nordic's NC22, the 22RB's predecessor, a forum, read Oct 1, 2026 the page, harvested Oct 1, 2026
A different, older Nordic .22 upper, which shipped with a flash hider. The same post: "The threads are 1/2x28 but the length of the threads is 0.400\"". 'Roughly': the ± is mine.
Photo 0.506 in ± 0.012 in used
the user's own 22RB, the bare muzzle from the side, the thread protector off; 2026-10-03, from the site owner
Scale: the thread's own pitch, 1/2-28 as the part states it (28 to the inch: 34 to 35 px a pitch); it checks against the thread's major diameter, 315 px over that pitch = 0.49 to 0.50 in. Read by on the lower silhouette, in the barrel's mid-plane: the muzzle face at px 964 ± 2; a plain pilot 0.031 long; ten crests (984 to 1192: nine pitches, 0.321); the thread running out at 1214, 0.385 from the face; a plain relief smaller than the thread, 0.120 long; the shoulder at 1293 ± 3, the same column top and bottom. ± is the two end picks and the pitch's 3% growth along the photo; the crest count is exact. The floor tape beside it reads 0.532 over the same span, which is 0.506 from a lens 16 in up
Longer than the .400 SilencerCo makes the Sparrow 22 for, shorter than its spacer's .600 to .650.
The barrel's own threaded end, bare, scaled by its own thread. The protector's length less the face's setback (0.465) and the NC22 owner's 0.48 were its length seen from outside.
protector and user differ by 0.041 in beyond what each states it is good to.
How far the barrel's reduced, threaded end stands ahead of its shoulder: a muzzle device made for a given thread length shoulders only if this is no longer. Nordic doesn't publish it. How much of it carries thread: on the user's own barrel (2026-10-03) a plain pilot 0.03 long, thread to 0.385 from the face, then a relief 0.12 long to the shoulder; the owner of an older Nordic NC22 gives 0.400 of roughly 0.48.
Muzzle thread: its major diameter (its crests)0.496 in ± 0.0033 in 12.6 mmConfirmedStandard: US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213
Standard “1/2-28 UNEF-2A MAJOR DIA .4989/.4924” used
US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213, from the site owner
The middle of the two limits, ± half their spread.
Photo 0.485 in ± 0.01 in
the user's own 22RB, the bare muzzle from the side, the thread protector off; 2026-10-03, from the site owner
Scale: the thread's own pitch on the lower silhouette, 28 to the inch: ten crests from column 982.5 to 1188 (22.83 px each, 639 px/in); the upper silhouette's are 22.6. Read by crest to crest across the silhouette: the upper crests' tips at row 1140 ± 1, the lower at 1450 ± 1: 310 px, 13.6 pitches (a 1/2 in thread of 28 to the inch is 13.9 across; 1/2-20 would be 10, 7/16-28 12.2). ± is 3 px of the edges and the pitch's 1% between the two silhouettes
The thread the barrel is sold with, at the Army drawing's limits for it; the photo's 0.485 ± 0.01 is the crests' silhouette, 2% under and inside its own ±.
The Army barrel's 1/2-28 thread, for the 1/2-28 this barrel is sold with: what the model's thread is drawn at. Neither figure of the drawing is a measurement of this barrel; the user's photo of it bare is, and reads its crests 2% under the drawing's middle, inside what its edges and its scale can tell.
Muzzle thread: its minor diameter (its roots)0.455 in ± 0.002 in 11.6 mmConfirmedStandard: US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213
Standard “MINOR DIA .4551 MAX” used
US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213, from the site owner
A maximum: the ± is mine, as bcm-16-mid-barrel.thread_minor_d has it.
Photo 0.453 in ± 0.007 in
the user's own 22RB, the bare muzzle from the side, the thread protector off; 2026-10-03, from the site owner
Scale: the thread's own crests in the same view, top and bottom of its silhouette (rows 1140 and 1450: 310 px across), taken as its major diameter (muzzle_thread_major_d, 0.4957). Read by the roots' edges in the same view: the upper ones at rows 1153 to 1156.6 in six columns between crests (1154 ± 1.5), the lower at 1437.5: 283.5 px, 0.9145 of the crests'. A helix's roots are partly hidden behind the next flank in a silhouette, which would read them large, not small. ± is the edges and the major diameter's own
The drawing's figure for the thread, which the user's barrel reads within 0.002 of.
The drawing gives a maximum and the model draws the roots there. On the user's barrel the roots read 0.9145 of the crests, which at the drawing's major diameter is 0.453.
Muzzle thread: its pitch0.036 in ± 0.00005 in 0.9 mmConfirmedStandard: US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213
Standard “1/2-28 UNEF-2A” used
US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213, from the site owner
Published “The threads are 1/2x28 but the length of the threads is 0.400"”
Northeast Shooters forum, 'Nordic NC22 .22lr AR Review', post 15 (2020-10-12): an owner of Nordic's NC22, the 22RB's predecessor, a forum, read Oct 1, 2026 the page, harvested Oct 1, 2026
One thread by both; the drawing is the one that defines it.
28 threads to the inch. Nordic's own page isn't on file with the words; the NC22's owner states them, the Army's 1/2-28 is the same thread, and the user's photo counts 13.6 pitches to the thread's diameter, which is 1/2-28 and no other common thread (see muzzle_thread_major_d#user).
Muzzle thread: the muzzle face to its first crest0.029 in ± 0.004 in 0.7 mmProvisionalPhoto: the user's own 22RB, the bare muzzle from the side, the thread protector off; 2026-10-03
Photo 0.029 in ± 0.004 in used
the user's own 22RB, the bare muzzle from the side, the thread protector off; 2026-10-03, from the site owner
Scale: the thread's own pitch on the lower silhouette (22.83 px, 639 px/in). Read by on the lower silhouette: the face at column 964.5 ± 2 (964 in the reading of 2026-10-03, 965 here), the first crest's tip at 982.5 to 984: 18 to 19.5 px. The 2026-10-03 reading gave 0.031 (muzzle_thread_length#user: 'a plain pilot 0.031 long')
Ahead of the first crest the end is plain: a pilot a little under the roots' diameter (muzzle_pilot_d), half a pitch of lead-in flank behind it. The helix puts the first crest of the upper silhouette half a pitch nearer the face (column 975): the model's thread is rings, placed where the lower silhouette has its crests.
Muzzle thread: the muzzle face to where the thread runs out0.385 in ± 0.006 in 9.8 mmProvisionalPhoto: the user's own 22RB, the bare muzzle from the side, the thread protector off; 2026-10-03
Photo 0.385 in ± 0.006 in used
the user's own 22RB, the bare muzzle from the side, the thread protector off; 2026-10-03, from the site owner
Scale: the thread's own pitch on the lower silhouette (22.83 px, 639 px/in; 23.1 in the reading of 2026-10-03). Read by the last full crest at column 1188 to 1192, the thread running out at 1214 ± 3 (the reading of 2026-10-03, looked at again on the same crop: muzzle_thread_length#user)
Behind it the end is a plain relief (muzzle_relief_d) to the shoulder: 0.121 in of the 0.506. Ten full crests and the run-out of an eleventh.
Muzzle thread: the relief's diameter, between the thread and the shoulder0.441 in ± 0.007 in 11.2 mmProvisionalPhoto: the user's own 22RB, the bare muzzle from the side, the thread protector off; 2026-10-03
Photo 0.441 in ± 0.007 in used
the user's own 22RB, the bare muzzle from the side, the thread protector off; 2026-10-03, from the site owner
Scale: the thread's own crests in the same view, top and bottom of its silhouette (rows 1140 and 1450: 310 px across), taken as its major diameter (muzzle_thread_major_d, 0.4957). Read by the relief's upper edge in three columns (1225, 1255, 1270): rows 1156.9, 1157.8, 1156.9, a strong edge (40 to 100 of 255); about the axis the crests give (row 1295) that is 137.8 px, 275.6 across, 0.889 of the crests'. ± is the edges and the major diameter's own
A plain neck a little under the thread's roots. Its lower edge is in the shoulder's shadow in this photo and isn't read: the diameter is its upper edge about the thread's own axis.
Muzzle thread: the plain pilot's diameter, at the muzzle face0.443 in ± 0.007 in 11.3 mmProvisionalPhoto: the user's own 22RB, the bare muzzle from the side, the thread protector off; 2026-10-03
Photo 0.443 in ± 0.007 in used
the user's own 22RB, the bare muzzle from the side, the thread protector off; 2026-10-03, from the site owner
Scale: the thread's own crests in the same view, top and bottom of its silhouette (rows 1140 and 1450: 310 px across), taken as its major diameter (muzzle_thread_major_d, 0.4957). Read by the pilot's edges at column 968, between the face and the first flank: rows 1157.4 and 1434.0, 277 px about the same axis (1295.7), 0.8935 of the crests'. ± is the edges and the major diameter's own
The bore, as it shows in the muzzle face0.218 in ± 0.02 in 5.5 mmCorroboratedPhoto: Nordic: the 22RB's muzzle end, three-quarter view, 1200 px
Photo 0.218 in ± 0.02 in used
Nordic: the 22RB's muzzle end, three-quarter view, 1200 px, harvested
Scale: the protector's face, its vertical extent = the barrel's OD (nordic-22rb-upper.barrel_od, 0.717; the protector is flush with the barrel in the side photos). Read by the bore's vertical extent against the face's on a 4x crop, both ellipses' long axes (the view's tilt shortens them alike): 0.304 of the face
Photo 0.232 in ± 0.015 in
the user's own 22RB, the muzzle end straight on, the rail at the bottom, a tape across above; 2026-10-03, from the site owner
Scale: the protector's own face in the same view: a circle fitted to its rim on 521 of 720 rays, 226.2 px in radius (rms 1.3), taken as nordic-thread-protector.od (0.736): 615 px/in. Read by a circle fitted to the dark hole's rim on 511 rays: 71.2 px in radius, rms 4.5: 0.315 of the face. The rim is ragged with the rifling's reflections in the crown, and its centre is 10 px from the face's: the dark disc takes in the crown's shadow, and reads the hole large. ± is the fit's rms on both sides
Kept beside the other reading, not adopted: a hole and its shadow.
The hole's own rim, seen from the side of the axis where the crown doesn't shadow it. The user's face-on photo reads the dark disc, crown and all, 0.014 larger: inside the two ±.
The dark hole in the barrel's end face (.22 LR barrels are bored about 0.217 to 0.222 in, bore to groove: not a source). It was nordic-thread-protector.bore_d until 2026-10-06, kept there because the protector's sleeve was drawn with the hole in it; the barrel is drawn with its own bore now, right through. The lands and the grooves aren't told apart, and the crown's recess round the hole (a ring 0.36 in across in the face-on photo) isn't drawn: how deep it is isn't read.
Charging-handle latch to muzzle22.88 in ± 0.06 in 581.2 mmConflictPhoto: left side, NC22RB-UPPER-16-KIT_3_HR via Aerospace Arms
Photo “22.6–22.9 in”
not yet archived, from the project brief
Scale: not recorded in brief. Read by distortion model A (which model gave which end is not recorded)
Photo “22.6–22.9 in”
not yet archived, from the project brief
Scale: not recorded in brief. Read by distortion model B (which model gave which end is not recorded)
Photo 22.88 in ± 0.06 in used
left side, NC22RB-UPPER-16-KIT_3_HR via Aerospace Arms, harvested
Scale: top-rail Picatinny slots: 49 slots, rms 0.001 in, drift −1.0%. Read by silhouette end to end through the cubic model, linear beyond the rail (≈2 in each end). The camera is slightly elevated; the length effect is negligible
Photo 22.56 in ± 0.25 in
right side, Nordic NC22-16-Upper-V2, harvested
Scale: top-rail Picatinny slots: 37 slots, rms 0.017 in. Read by same method; 4.6 in extrapolated at the rear at 50 px/in, hence the larger ±
Highest-quality calibration (0.001 in rail fit at 84 px/in). Agrees with the brief's upper value (22.9). The lower-resolution photo and the brief's other model sit near 22.6; calipers settle it.
model-a and model-b differ by 0.3 in beyond what each states it is good to.
model-a and harvest-left differ by 0.28 in beyond what each states it is good to.
model-b and harvest-right differ by 0.34 in beyond what each states it is good to.
harvest-left and harvest-right differ by 0.32 in beyond what each states it is good to.
Muzzle (thread protector face) ahead of takedown pin21.645 in ± 0.025 in 549.8 mmConflictPhoto: the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03
Worked out 21.245 in
{asm.v1.oal_pos1} - {magpul-moe-sl-carbine.butt_behind_pin_pos1}, from the project brief
The brief's overall length minus the position-1 butt. It's circular for an OAL test, so the photo measurements below are the independent ones. 21.43 until 2026-10-05, when it moved with the MOE SL's seat: the stock's position-1 butt was put 0.185 in further back on a photo of one installed (magpul-moe-sl-carbine.butt_behind_pin_pos1), and this is that much less.
Photo 21.638 in ± 0.035 in
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0. Read by silhouette x_max along the rail model; ± is 3× rail rms plus edge and anchor error
Most forward silhouette point: the near rim of the thread protector's flat face, which this photo sees from about 19 degrees behind square (the protector's seam shows as an arc, sag 0.122 in at the barrel's radius: a copy on file). If the rail model's scale is that of the plane through the bore, the face's centre is 0.12 in behind this reading; if it is that of a plane 0.25 in nearer the lens (where the lug holes' near rims are: the pin-only frame agrees with the rail model at the muzzle to 0.008 in), 0.03 in behind. Which plane it is isn't established, so the reading stands uncorrected and the ± doesn't cover the first case (M6: open).
Photo 21.326 in ± 0.076 in
right side, Nordic NC22-16-Upper-V2, harvested
Scale: rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0. Read by silhouette x_max along the rail model; ± is 3× rail rms plus edge and anchor error
Photo 21.645 in ± 0.025 in used
the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03, from the site owner
Scale: the rail's 49 slots, found at mid-depth of the teeth (a projective fit to their centres: 0.3 to 0.6 px rms, 106 to 120 px/in), and the two lug holes' see-through centres, all on the centre plane; a camera pose fitted to them. Checks: the lug holes read 6.383 apart directly (+0.13%), the handguard's M-LOK slits 1.573 to 1.582 apart (40 mm), the receiver's underside 0.24 to 0.25 above the pins (the deck's 0.254). Read by the thread protector's front face, taken where the end's profile meets the protector's edges (at 0.86 and 0.92 of its radius: the face is seen from a little behind, so the silhouette's end bulges at the axis and its forward-most point reads 0.05 further): 21.648, 21.656, 21.637, 21.646, 21.640; ± is the pick inside the face's rounded edge (0.012), the anchor (0.007) and the scale over 21.6 in
The user's own upper in five photos, 21.637 to 21.656. The left product photo agrees (21.638); the right one reads the whole upper about 1.2% short (21.326).
from-oal and left differ by 0.393 in beyond what each states it is good to.
from-oal and right differ by 0.081 in beyond what each states it is good to.
from-oal and user differ by 0.4 in beyond what each states it is good to.
left and right differ by 0.312 in beyond what each states it is good to.
right and user differ by 0.319 in beyond what each states it is good to.
Rear of the upper (the charging handle's T's rear face, the handle home) behind the takedown pin0.86 in ± 0.03 in 21.8 mmConflictPhoto: the user's own 22RB from above, the rail's teeth from end to end; 2026-10-03
Photo 1.239 in ± 0.035 in
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0. Read by silhouette x_min along the rail model (negated); ± is 3× rail rms plus edge and anchor error
Rearmost silhouette point (charging-handle latch).
Photo 1.236 in ± 0.076 in
right side, Nordic NC22-16-Upper-V2, harvested
Scale: rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0. Read by silhouette x_min along the rail model (negated); ± is 3× rail rms plus edge and anchor error
Photo 0.86 in ± 0.03 in used
the user's own 22RB from above, the rail's teeth from end to end; 2026-10-03, from the site owner
Scale: the rail's slots, found by their walls' dark lines (0.42 px rms): the rail's own plane. Read by the charging handle's T's rear face, straight and square to the rail, 1.656 behind the first slot's centre (0.795). The side photos have the T's wing tip, 0.985 in off the centre plane, at -0.950 and -0.943 apparent, which is -0.87 with the lens allowed for. ± is the slot grid (0.012) and which wall a shadow favours (0.02)
The handle is home against the rail block. The two product photos' 1.24 isn't reproduced on the user's upper: 0.38 in further back, in photos whose anchor is 0.08 off at most; what stood there in Nordic's photos (a latch, a handle not home) isn't known.
The user's own upper, read in the rail's plane from above, the side photos agreeing. The product photos' 1.239 and 1.236 agree with each other and not with the part in hand.
left and user differ by 0.379 in beyond what each states it is good to.
right and user differ by 0.376 in beyond what each states it is good to.
Barrel OD (profile)0.736 in ± 0.02 in 18.7 mmCorroboratedPhoto: the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03
Photo 0.717 in ± 0.035 in
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0. Read by median silhouette height 0.25–1.0 in behind the forward tip (a cylinder's diameter is unaffected by camera elevation)
Muzzle section OD. The thread protector and exposed barrel read the same diameter.
Photo 0.711 in ± 0.076 in
right side, Nordic NC22-16-Upper-V2, harvested
Scale: rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0. Read by median silhouette height 0.25–1.0 in behind the forward tip (a cylinder's diameter is unaffected by camera elevation)
Photo 0.736 in ± 0.02 in used
the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03, from the site owner
Scale: the rail's 49 slots, found at mid-depth of the teeth (a projective fit to their centres: 0.3 to 0.6 px rms, 106 to 120 px/in), and the two lug holes' see-through centres, all on the centre plane; a camera pose fitted to them. Checks: the lug holes read 6.383 apart directly (+0.13%), the handguard's M-LOK slits 1.573 to 1.582 apart (40 mm), the receiver's underside 0.24 to 0.25 above the pins (the deck's 0.254). Read by the thread protector's diameter across its silhouette: 0.732, 0.735, 0.737, 0.737, 0.739. The polished barrel behind it mirrors the floor and reads thin (0.55): not read
The protector's (0.732 to 0.739 in five photos), which the barrel it sleeves is taken to equal: in the bare-muzzle photo (c0e654135597) the barrel is 1.5 times its 1/2 in thread across, 0.74 ± 0.02, which is the ± here. What the barrel measures under the handguard isn't seen.
The protector's diameter on the user's own upper in five photos (0.732 to 0.739); the barrel it sleeves is as large: in the bare-muzzle photo (c0e654135597) the barrel is 1.5 times its 1/2 in thread across (0.74 ± 0.02). The product photos' 0.717 and 0.711 are a glossy tube on white, which reads thin (CLAUDE.md).
Not in the brief. Needed for the barrel mesh. M1b.
Handguard length13.538 in ± 0.05 in 343.9 mmProvisionalWorked out: {.handguard_front_x} - {.handguard_rear_x}
Worked out 13.538 in ± 0.05 in used
{.handguard_front_x} - {.handguard_rear_x}, harvested
Not published (the seed's gaps); Aawee's 13.5 in belongs to a handguard model that isn't confirmed for the 22RB. From the photos: the handguard front less the receiver/handguard seam. The user's tape on their own upper (4e2b3425b362, 2026-10-02: laid on the right side, the seam under it at 13.57, the handguard's front showing 0.02 to 0.12 behind its zero) reads 13.50, and isn't a measurement of this: the handguard's front is turned to a cone (handguard_nose_opening_d), so what shows beside the tape's end is the cone's surface or its rim, up to 0.44 in below the tape's plane, seen from a lens 16 in up and somewhere behind it. Over the middle of the photo that is 0.25 to 0.3 in of parallax, which is the whole difference; where the lens stood isn't known, so no figure is taken. A tape hooked on the front face would say (STATUS, photos to ask for).
Handguard's mouth: the bore's diameter at its front rim, inside the chamfer1.53 in ± 0.03 in 38.9 mmConflictPhoto: the user's own 22RB, the muzzle end straight on, the rail at the bottom, a tape across above; 2026-10-03
Photo 0.721 in ± 0.03 in
right side, Nordic NC22-16-Upper-V2, 1200 px, harvested
Scale: rail model 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%, tilt +0.37°) along the rail and its local scale across it, anchored at the takedown lug (91.5, 475.5); the three nose figures are differences read within 0.4 in of one another in this one photo, so its frame's offset from the left photo's (0.245 in at the front) is out of them. Read by where the two slopes end on the barrel's silhouette: y 0.509 below and 1.23 above (profiles.side). The barrel there is 0.711 across in this photo (barrel_od's right reading), so the opening is the barrel's diameter and a clearance the photo doesn't resolve; ± is a pixel and a half
Photo 1.53 in ± 0.03 in used
the user's own 22RB, the muzzle end straight on, the rail at the bottom, a tape across above; 2026-10-03, from the site owner
Scale: the octagon's own width in the same view (handguard_width). Read by the mouth as the end-on photos show it: an open tube, the M-LOK slots' light in seven rows running away down the bore round the barrel; at its rim a turned ring between r 0.765 and 0.797, the edge of a chamfer from the flats in to r 0.765
The right product photo's side outline had been read as a cone closing on the barrel to a 0.721 opening, 0.136 ahead of the flats' front and leaving them 0.172 behind it (handguard_nose_rim_ahead and handguard_nose_flat_behind, dropped with this reading): it is the open mouth seen from the side.
The user's own upper, straight on: an open tube. The side photo's "cone" was the mouth's chamfer and the bore's far wall.
right-outline and user-end differ by 0.809 in beyond what each states it is good to.
The handguard's front isn't square: it is turned to a cone that closes on the barrel. In the side view its silhouette slopes back above and below the barrel, from where it meets the barrel's to the flats. Three figures give the cone (this, handguard_nose_rim_ahead, handguard_nose_flat_behind), each from the right product photo's traced outline (profiles.side: (19.846, 0.088) the bottom flat's front end, (20.03, 0.269), (20.127, 0.48), (20.156, 0.509) on the barrel's underside; (20.151, 1.23) on its top, (19.962, 1.615) at the rail's neck). The user's own upper shows the same nose: from above, the front corners cut back in plan (d20d09340d49); lying on its side, a rounded front, as a cone through an octagon's flats is (4e2b3425b362). handguard_front_x is a point part-way up this cone (where the silhouette is half an inch taller than the barrel), which M5 to 2026-10-02 drew as a square front.
Handguard rear end (the seam with the receiver's front), X6.597 in ± 0.036 in 167.6 mmConflictWorked out: {.receiver_rail_front_x}
Photo 6.47 in ± 0.035 in
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0. Read by the seam picked at x 1305 ± 1.5 px over rows 940–1040 on a 3× gridded crop, mapped through the rail model; ± is the pick (0.018) plus 3× rail rms and the anchor
Photo 6.382 in ± 0.054 in
right side, Nordic NC22-16-Upper-V2, harvested
Scale: rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0. Read by the seam picked at x 422.5 ± 1 px over rows 400–450 on a 9× gridded crop, mapped through the rail model; ± is the pick (0.02) plus 3× rail rms
Photo 6.494 in ± 0.04 in
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0; the lens from the same rail (its teeth's silhouettes are narrowest at px 1005 and widen 0.0069 in for each inch off it, across a rail 0.835 in wide). Read by the left pick (6.47), carried from the receiver's near wall, where the seam is seen, to the rail's mid-plane, where the rail model's scale is. The wall stands half the receiver's width ({.width} / 2 = 0.801 in) nearer the lens, and the pick is 3.59 in off the lens's axis (px 1305 against 1005 at 83.6 px/in), toward the rear: a point that much nearer shows 3.59 × 0.801 / 0.835 × 0.0069 = 0.0238 in further from the axis than it is, so the seam is that much further forward. ± is the pick's (0.035) plus the correction's own doubt (the receiver's width ± 0.06, the widening read to about a tenth: 0.004)
The correction the 2026-10-02 rail-break work measured and left unapplied (STATUS, small issues: the receiver rail's last tooth drawn 0.05 in narrow). The right photo's pick needs the same kind of correction and has no lens reading to make it with.
Worked out 6.597 in ± 0.036 in used
{.receiver_rail_front_x}, from the site owner
Where the receiver's rail ends: the two parts' rails break where the parts do (the left photo shows the last tooth's front face on the seam's line; from above, on the user's own upper, the seam runs into that face).
The seam is where the rail breaks, and that is known best: a whole tooth's front face on the slot grid (receiver_rail_front_x). The left photo's own reading of the seam, carried to the rail's plane (6.494 ± 0.04), agrees; the right photo reads ~1.2% short along the upper. On the user's own upper the seam stands the same 0.06 in behind the pivot lug's front edge as in the left product photo (4e2b3425b362: 6 px at 104 px/in; 6 px at 84).
left and rail differ by 0.127 in beyond what each states it is good to.
right and left-midplane differ by 0.112 in beyond what each states it is good to.
right and rail differ by 0.215 in beyond what each states it is good to.
left-midplane and rail differ by 0.103 in beyond what each states it is good to.
A vertical seam just ahead of the pivot lug, plain in both rail-calibrated side photos; the handguard's clamp boss (two screws) hangs below just ahead of it (x 6.8–7.9). Not on the silhouette, so picked on gridded crops and mapped through each photo's rail model. The right photo reads short along the whole upper (its handguard front is 0.245 in short at x 20, ~1.2%), which predicts ~0.08 in here: the two agree once that's allowed for.
X of the rearmost top-rail slot center0.795 in ± 0.015 in 20.2 mmConflictPhoto: the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03
Photo 0.713 in ± 0.035 in
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0. Read by silhouette slot_first_x along the rail model; ± is 3× rail rms plus edge and anchor error
Rearmost detected top-rail slot center; slot index 0 in the build's optic_slot/magnifier_slot.
Photo 0.795 in ± 0.015 in used
the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03, from the site owner
Scale: the rail's 49 slots, found at mid-depth of the teeth (a projective fit to their centres: 0.3 to 0.6 px rms, 106 to 120 px/in), and the two lug holes' see-through centres, all on the centre plane; a camera pose fitted to them. Checks: the lug holes read 6.383 apart directly (+0.13%), the handguard's M-LOK slits 1.573 to 1.582 apart (40 mm), the receiver's underside 0.24 to 0.25 above the pins (the deck's 0.254). Read by the rearmost slot's centre: 0.797 and 0.799 in the two photos taken square on, 0.790, 0.788 and 0.787 in the three taken from 9 in toward the lugs; ± is their spread and the anchor
The left product photo's 0.713 is anchored at its takedown lug alone, in a photo that reads the pins 1.25% short (pin_spacing's note): against its own pivot hole its seam stands 0.19 to 0.21 ahead, as here (0.225).
The user's own upper in five photos, framed by both lug holes and the rail itself. The product photo's grid sat 0.08 behind it: its anchor, not the part.
left and user differ by 0.082 in beyond what each states it is good to.
Needed to index optics by slot. M1b, from a rail-calibrated side photo.
Frontmost top-rail slot center, X19.693 in ± 0.02 in 500.2 mmConflictPhoto: the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03
Photo 19.625 in ± 0.035 in
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0. Read by silhouette slot_last_x along the rail model; ± is 3× rail rms plus edge and anchor error
Photo 19.693 in ± 0.02 in used
the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03, from the site owner
Scale: the rail's 49 slots, found at mid-depth of the teeth (a projective fit to their centres: 0.3 to 0.6 px rms, 106 to 120 px/in), and the two lug holes' see-through centres, all on the centre plane; a camera pose fitted to them. Checks: the lug holes read 6.383 apart directly (+0.13%), the handguard's M-LOK slits 1.573 to 1.582 apart (40 mm), the receiver's underside 0.24 to 0.25 above the pins (the deck's 0.254). Read by the 49th slot's centre: 48 pitches ahead of the first (0.795), read at 19.700 and 19.702 in the two photos taken square on
The user's own upper; 48 pitches ahead of the first slot. The product photo's 19.625 sat behind it with its grid.
left and user differ by 0.068 in beyond what each states it is good to.
Top rail's rear end (the rail head's rear face), X0.57 in ± 0.02 in 14.5 mmConflictPhoto: the user's own 22RB: the receiver's rear end from above, close, the handle home; 2026-10-05
Photo -0.552 in ± 0.029 in
right side, Nordic NC22-16-Upper-V2, 1200 px, harvested
Scale: rail model 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%, tilt +0.37°) along the rail and its local scale across it (52.2 px/in at the anchor), anchored at the takedown lug (91.5, 475.5). Read by x_min in y [2.03, 2.3] of the traced outline (tools/trace.py); the rail head's rear face: rows above the charging handle's top (2.00) and below the tooth tops (2.07)
Photo 0.57 in ± 0.02 in used
the user's own 22RB: the receiver's rear end from above, close, the handle home; 2026-10-05, from the site owner
Scale: the T's own width beside it in the rail's plane (charging_handle_t_width: 1318.4 px end to end, 669 px/in), which a tooth's top flat (437.7 px for the standard's 0.656: 667) and slot 0's front wall (1.755 in ahead of the T's rear face for the ledger's 1.758) agree with. Read by the rail from above: slot 0's rear wall at column 1599, the standard's head behind it at its full width for 80 px (columns 1519 to 1599), and behind that the rail at 0.64 in across with upright sides (columns 890 to 1519). The T's rear face is at column 560.8 on the centre line: (1519 - 560.8) / 667 less rear_behind_pin. ± is the corner's round (10 px) and the scale's 1%
They are two ends of two things. Seen from above on the user's own upper the standard's head, shoulders and all, stops 0.12 in behind slot 0; from there back the rail is a tongue of its top's width with a round nose (rail_tongue_*), which is what the product photo's silhouette has at -0.552. The app draws the standard's head from here.
right-photo and user differ by 1.122 in beyond what each states it is good to.
With rail_front_x, where the app draws the rail head to MIL-STD-1913 (std.picatinny.*) over the traced body. The rail is solid from here to the first slot (rail_slot0_x). Until 2026-10-05 this was the rail's rearmost point in a side photo, and the head was drawn at its full width from there: behind this the rail is a tongue as wide as its top, over the charging handle (rail_tongue_width, rail_tongue_rear_x, rail_tongue_bottom_y), which the receiver's model carries.
Top rail's front end (the last tooth's front face), X19.98 in ± 0.03 in 507.5 mmCorroboratedPhoto: the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03); and 7f994902ea3b (from above
Photo 19.946 in ± 0.02 in
left side, NC22RB-UPPER-16-KIT_3_HR, 2000 px, harvested
Scale: rail model 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%, tilt +0.15°) along the rail and its local scale across it (85.9 px/in at the anchor), anchored at the takedown lug (1853.5, 1074.5). Read by x_max in y [2.03, 2.3] of the traced outline (tools/trace.py); the last tooth's front face: rows between the slot floors (2.00) and the tooth tops (2.09–2.11)
Photo 19.98 in ± 0.03 in used
the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03); and 7f994902ea3b (from above, from the site owner
Scale: the rail's 49 slots, found at mid-depth of the teeth (a projective fit to their centres: 0.3 to 0.6 px rms, 106 to 120 px/in), and the two lug holes' see-through centres, all on the centre plane; a camera pose fitted to them. Checks: the lug holes read 6.383 apart directly (+0.13%), the handguard's M-LOK slits 1.573 to 1.582 apart (40 mm), the receiver's underside 0.24 to 0.25 above the pins (the deck's 0.254). Read by the last tooth's front face, the perspective of the rail's near edge taken off: 19.98 from the side; 19.95 from above, in the rail's own plane
The user's own upper, from the side and from above; the product photo's 19.946 ± 0.02 agrees.
The last slot (rail_last_slot_x 19.625) plus half a slot puts the last tooth at 19.728–19.946: 0.218 wide, against the standard's 0.188 (pitch less slot), within the ±. The right photo can't give it: there the lens looks along the slots and the far teeth fill them, so its outline is smooth from x ≈ 16.6.
Top-rail slots (continuous run seen in the side view)49CorroboratedPhoto: the user's own 22RB from above, rail up, a tape on the floor beside it; supplied in chat 2026-10-02
Photo 49 count
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0. Read by slot indices spanned by the rail fit (a rail end hidden by a part would be missed)
Photo 49 count used
the user's own 22RB from above, rail up, a tape on the floor beside it; supplied in chat 2026-10-02, from the site owner
Scale: none needed (a count). Read by every tooth marked on the rail from above and checked by eye: 49 teeth from the front one to the last before the solid block under the charging handle, a slot behind each: 49 slots. The user's suggestion (2026-10-02: "count the rail teeth and see exactly how many lie to either side of that seam")
Counted on the user's own upper; the product photo's rail fit had given the same.
Counted tooth by tooth on the user's own upper; the left product photo's rail fit spans the same 49.
Top-rail slots on the receiver (behind the seam)15ProvisionalPhoto: the user's own 22RB from above, rail up, a tape on the floor beside it; supplied in chat 2026-10-02
Photo 15 count used
the user's own 22RB from above, rail up, a tape on the floor beside it; supplied in chat 2026-10-02, from the site owner
Scale: none needed (a count). Read by the seam found where the handguard's body ends and the receiver's narrower one begins (its line shows on the body beside the rail with the contrast raised), and the teeth counted either side of it: 34 ahead, 15 behind and the block
Which side of the seam each slot is on, counted on the user's own upper from above: the handguard's rail has 34 teeth and 34 slots and ends at the seam with a slot; the receiver's begins there with a whole tooth and has 15 teeth, 15 slots, then the solid block under the charging handle. So of the run's 49 slots (rail_slots), indexed from the rear, 0 to 14 are the receiver's and 15 to 48 the handguard's: what the positions give (receiver_rail_front_x between slots 14 and 15), now counted.
Receiver rail's tooth at the seam, how much narrower than its neighbours0.005 in ± 0.009 in 0.1 mmCorroboratedPhoto: the user's own 22RB from above, rail up, a tape on the floor beside it; supplied in chat 2026-10-02
Photo 0.005 in ± 0.009 in used
the user's own 22RB from above, rail up, a tape on the floor beside it; supplied in chat 2026-10-02, from the site owner
Scale: the rail's own pitch beside it (30.8 px a pitch there, 78 px/in). Read by tooth tops along the rail's middle (the lighter flats; edges at the level midway between a flat and the slots beside it): the receiver's first tooth 13.3 px against 13.2 and 14.2 for the teeth either side of it (the widths rise along the photo with its scale: 13.7 expected between them), so 0.4 px narrow; ± is half a pixel at each edge
Photo 0.004 in ± 0.009 in
the user's own 22RB from above, a second frame; supplied in chat 2026-10-02, from the site owner
Scale: the rail's own pitch beside it (30.4 px a pitch there, 77 px/in). Read by as user-top-b, in the second frame: 13.3 px against 13.4 and 13.8 either side (13.6 expected), 0.3 px narrow
The frame in which every tooth was found and counted; the other agrees.
Whether the receiver's rail ends at the seam with a whole tooth. The side photos had its front face at the seam within a pixel, but the seam's own position (read on a wall, mapped through a rail model) left that tooth drawn 0.05 and then 0.03 in narrower than the rest. From above, on the rail's top, the tooth is measured against its neighbours in the same plane: it is whole.
Handguard's front end (its front-most rim), X20.135 in ± 0.04 in 511.4 mmConflictPhoto: the user's own 22RB, a tape hooked on the handguard's nose and laid back along its side flat; 2026-10-03
Photo 20.263 in ± 0.035 in
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0. Read by forward-most x where the silhouette height exceeds the front plateau (0.717 in) by 0.5 in
Handguard front face: where the silhouette steps up from the barrel section.
Photo 20.018 in ± 0.076 in
right side, Nordic NC22-16-Upper-V2, harvested
Scale: rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0. Read by forward-most x where the silhouette height exceeds the front plateau (0.711 in) by 0.5 in
Photo 20.135 in ± 0.04 in used
the user's own 22RB, a tape hooked on the handguard's nose and laid back along its side flat; 2026-10-03, from the site owner
Scale: the tape itself, read where it lies: its ticks located one by one beside the seam. Read by the seam on the side flat reads 13.550 and 13.564 on the tape; the hook's outer face stands 0.014 and 0.022 beyond the tape's zero, so the handguard bears on the hook's inner face, whose tab is taken as 0.04 thick (not measured): 13.535 from the seam to the front-most rim, and the seam is at 6.60 (handguard_rear_x). Corroborated across planes, not used: the near side flat's front edge reads 20.278 in the far photos (0.8 in nearer the lens: 20.13 to 20.17 true), the body's front 20.12 from above, the floor tape 1.46 ± 0.06 from the front to the protector's face. ± is the hook's tab and whether it touched (0.03) and the seam (0.015)
The 2026-10-02 tape photo's 13.50 to 13.57, set aside then as parallax, was right.
A tape lying on the part, read in its own plane, twice. The left product photo's 20.263 is the near flat's edge as its lens saw it (the user's far photos read the same 20.28 apparent); the 13.88 to a rim that the cone was thought to carry came from the right photo's outline.
left and right differ by 0.245 in beyond what each states it is good to.
left and user-tape differ by 0.128 in beyond what each states it is good to.
right and user-tape differ by 0.117 in beyond what each states it is good to.
Receiver rear face (below the charging handle), X-0.84 in ± 0.02 in -21.3 mmConflictPhoto: the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03
Photo -0.983 in ± 0.035 in
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0. Read by silhouette x_min in y [0.35, 0.7] (rows at the anchor scale) along the rail model; ± is 3× rail rms plus edge and anchor error
Receiver rear face, below the charging handle and above the takedown lug (the band sits between the receiver bottom and the bore axis).
Photo -0.91 in ± 0.076 in
right side, Nordic NC22-16-Upper-V2, harvested
Scale: rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0. Read by silhouette x_min in y [0.35, 0.7] (rows at the anchor scale) along the rail model; ± is 3× rail rms plus edge and anchor error
Photo -0.84 in ± 0.02 in used
the user's own 22RB lying on a tile floor, each side, from 5 to 7 ft, zoomed; 2026-10-03, from the site owner
Scale: the rail's 49 slots, found at mid-depth of the teeth (a projective fit to their centres: 0.3 to 0.6 px rms, 106 to 120 px/in), and the two lug holes' see-through centres, all on the centre plane; a camera pose fitted to them. Checks: the lug holes read 6.383 apart directly (+0.13%), the handguard's M-LOK slits 1.573 to 1.582 apart (40 mm), the receiver's underside 0.24 to 0.25 above the pins (the deck's 0.254). Read by the bolt assembly's steel rear end, on the bore's axis: -0.833 and -0.854 in the two photos taken square on. The receiver's own rear face shows at -0.658 and -0.663 (its near edge: about -0.61, the standard's -0.621)
The user's own upper, the steel end on the centre plane. The product photos' -0.983 and -0.91 share the frame that put the rear 0.38 in back.
left and user differ by 0.143 in beyond what each states it is good to.
Cross-part question: this is 0.6 in behind the front of the Workhorse's buffer tower (bad-workhorse-lower.tower_front_x, −0.31). Both readings are corroborated by two photos each. Likely explanation: the tower's side walls run forward of the threaded ring (its internal threads are visible between them in both side photos), and the upper's rear nests between the walls. To confirm: a pin-calibrated side view of an assembled rifle. M6: the Army's drawing puts the threaded ring's front face 0.628 behind the takedown pin (std.ar15.buffer_tower_front_x) and a standard upper's rear just ahead of it, so this face, 0.35 further back in a band below the bore, stands inside the ring's 1.19 in bore: the rear of the .22 bolt assembly's housing, not the receiver's rear face.
Handguard size across the side flats (listed "outer diameter")1.602 in 40.7 mmCorroboratedPublished: Aawee, NCT3 15.3 in handguard (text relayed by the user; the page renders by script), a seller, read Sep 30, 2026
Published “Outer diameter 40.7mm, inner diameter 35.6mm.” used
Aawee, NCT3 15.3 in handguard (text relayed by the user; the page renders by script), a seller, read Sep 30, 2026 the page, from the site owner
Published “Outer diameter 40.7mm, inner diameter 35.6mm”
Aawee, NCT3 17.2 in handguard, a seller, read Sep 30, 2026 the page, harvested Sep 30, 2026
The listing that states the NC 22LR compatibility. Both lengths list the same profile.
Nordic's NCT3, which Aawee sells as matching the handguard on Nordic's M-LOK 22 uppers: 'Compatible with NC 22lr rifle upper receiver with M-LOK handguard like the original handguard.' Nordic's own photo of the 22RB's muzzle end shows the same octagon and slot layout. The listings don't say corners or flats. Read as across the side flats (M5): Aawee's straight end-on photo of the NCT3 (a copy on file) is 0.810 as wide across its side flats as it is tall from the bottom flat to the rail top, so with the 22RB's side-view height (2.04) it's 1.65 wide; 40.7 mm across the flats gives 1.60, across the corners only 1.48 (and then a section 1.83 tall, not 2.04). The rail runs straight into the upper diagonal faces: the octagon has no top flat.
Handguard bore (inside diameter)1.402 in 35.6 mmCorroboratedPublished: Aawee, NCT3 15.3 in handguard (text relayed by the user; the page renders by script), a seller, read Sep 30, 2026
Published “Outer diameter 40.7mm, inner diameter 35.6mm.” used
Aawee, NCT3 15.3 in handguard (text relayed by the user; the page renders by script), a seller, read Sep 30, 2026 the page, from the site owner
Published “Outer diameter 40.7mm, inner diameter 35.6mm”
Aawee, NCT3 17.2 in handguard, a seller, read Sep 30, 2026 the page, harvested Sep 30, 2026
Both listings agree; the same figure as the outer diameter's source (handguard_od).
The NCT3's end view shows a round bore inside the octagon, with the slots opening into it on every face but the top.
Handguard's foremost M-LOK slot, centre X18.976 in ± 0.02 in 482 mmConflictPhoto: the user's own 22RB, left side, square on from 5 to 7 ft; 2026-10-03
Photo 18.874 in ± 0.03 in
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0. Read by the barrel seen through the slots in the upper (y 978 px) and side (1035 px) rows: the bright runs' centres of the three full-length slots in each row, stepped forward by the 40 mm pitch (mlok.slot_pitch) to the first slot: six estimates 18.864–18.883; the runs' centres fall 1.58, 1.58, 1.54, 1.57, 1.57 in apart (1.575 is the pitch)
Photo 18.976 in ± 0.02 in used
the user's own 22RB, left side, square on from 5 to 7 ft; 2026-10-03, from the site owner
Scale: the rail's 49 slots, found at mid-depth of the teeth (a projective fit to their centres: 0.3 to 0.6 px rms, 106 to 120 px/in), and the two lug holes' see-through centres, all on the centre plane; a camera pose fitted to them. Checks: the lug holes read 6.383 apart directly (+0.13%), the handguard's M-LOK slits 1.573 to 1.582 apart (40 mm), the receiver's underside 0.24 to 0.25 above the pins (the deck's 0.254). Read by the foremost slot's centre in the lower diagonal row, seen through to the far wall (centre plane): the six full slots at 11.092, 12.670, 14.243, 15.817, 17.393, 18.976 (pitch 1.577 against 40 mm's 1.5748)
The user's own upper, through the pose that the pins and the rail fix; the product photo's 18.874 sat 0.10 behind, as its rail grid did.
left and user differ by 0.102 in beyond what each states it is good to.
M-LOK: the rearmost slot of each row, its length0.93 in ± 0.03 in 23.6 mmProvisionalPhoto: the user's own 22RB, left side, square on; 2026-10-03); bdb43e3235ed (from below
Photo 0.93 in ± 0.03 in used
the user's own 22RB, left side, square on; 2026-10-03); bdb43e3235ed (from below, from the site owner
Scale: the rail's 49 slots and the two lug holes' see-through centres, all on the centre plane, in one fitted camera pose (rail_slot0_x#user). Read by the rearmost opening of the lower diagonal row seen through to the far wall: 9.23 to 10.15 (0.92, about 0.94 with its ends' rounding), its front end on the 40 mm grid and its rear 0.31 short of a full slot's; the bottom face's row has the same short slot (strip px 1151 to 1254 against the diagonal's 1153 to 1253). Full slots read 1.22 to 1.24 where the lens looks straight through
Every row's rearmost slot is the short one: seven slots a face, six of them the standard's 32 mm.
Handguard M-LOK slots per face7ProvisionalPhoto: left side, NC22RB-UPPER-16-KIT_3_HR
Photo 7 count used
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: none (a count). Read by counted in the upper and side rows; the lower row's foreshortened slits agree
Through-slots; behind them each row ends in a blind panel the length of a slot, not drawn.
Receiver section: the block under the rail, width0.605 in ± 0.02 in 15.4 mmProvisionalPhoto: Nordic, looking forward down the receiver from the rear
Photo 0.605 in ± 0.02 in used
Nordic, looking forward down the receiver from the rear, harvested
Scale: the section's full width, 272 px = the receiver's 1.38 in (width): 197 px/in across. Read by the block's vertical sides at the rear face (px 521 and 640, 119 px), above where the chamfers start
Nordic's receiver is an extrusion (constant section): this rear face is its section, the rail machined off behind the rail's rear end.
Receiver section: the upper chamfers' top edge, Y1.645 in ± 0.02 in 41.8 mmCorroboratedPhoto: right side, Nordic NC22-16-Upper-V2
Photo 1.645 in ± 0.02 in used
right side, Nordic NC22-16-Upper-V2, harvested
Scale: rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper. Read by a horizontal edge on the receiver's side, the same row at u 180, 230 and 400
Photo 1.652 in ± 0.015 in
Nordic, 18 in 22RB upper, true right side, 4096 px, harvested
Scale: pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane. Read by horizontal edges at u 700 and 850 (1.649, 1.656)
Both photos agree to 0.007.
Receiver section: the upper chamfers' bottom edge (the sides' top), Y1.177 in ± 0.02 in 29.9 mmCorroboratedPhoto: right side, Nordic NC22-16-Upper-V2
Photo 1.177 in ± 0.02 in used
right side, Nordic NC22-16-Upper-V2, harvested
Scale: rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper. Read by horizontal edges at u 180, 230, 400 (1.164, 1.183, 1.183)
Photo 1.158 in ± 0.02 in
Nordic, 18 in 22RB upper, true right side, 4096 px, harvested
Scale: pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane. Read by horizontal edges at u 700 and 850 (1.169, 1.147)
Both photos agree within 0.02.
Receiver section: the lower corners' top edge, Y0.631 in ± 0.02 in 16 mmCorroboratedPhoto: right side, Nordic NC22-16-Upper-V2
Photo 0.631 in ± 0.02 in used
right side, Nordic NC22-16-Upper-V2, harvested
Scale: rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper. Read by horizontal edges at u 180, 230, 400 (0.625, 0.625, 0.644)
Photo 0.615 in ± 0.02 in
Nordic, 18 in 22RB upper, true right side, 4096 px, harvested
Scale: pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane. Read by horizontal edges at u 700 and 850 (0.618, 0.611)
Both photos agree within 0.02.
Receiver section: the lower corners' width (inward at the bottom)0.134 in ± 0.03 in 3.4 mmProvisionalPhoto: Nordic, looking forward down the receiver from the rear
Photo 0.134 in ± 0.03 in used
Nordic, looking forward down the receiver from the rear, harvested
Scale: the section's full width, 272 px = the receiver's 1.38 in (width): 197 px/in across. Read by the outline's width row by row at the rear face: 272 px down to 219 px at its last row above the lug (26.5 px a side); a lower bound: the curve may run further in under the lug
Receiver: the rear lower chamfers' width (inward at the bottom)0.23 in ± 0.02 in 5.8 mmProvisionalPhoto: the user's own 22RB, the rear end straight on; 2026-10-03
Photo 0.23 in ± 0.02 in used
the user's own 22RB, the rear end straight on; 2026-10-03, from the site owner
Scale: the receiver's own width across its side flats in the same view (712.5 px = 1.31 in: width; 544 px/in). Read by the outline's edge column by column (luminance 70): from the underside's edge to the side flat it is a straight line on both sides, 125 px across (0.23) over 195 px of height (0.36), the underside between them 463 px (0.85) and the side flats 290 px (0.53). A flat chamfer, not a round. ± is 5 px at each end of the line; the rear end's outline is spread over the 0.35 in of depth its rounded lower rear corner takes, under 3% of scale from where the lens stood
From below, straight down from 5 to 7 ft (bdb43e3235ed), the same chamfers show as a dark band 21 to 23 px wide inside each edge of a body 140.5 px across: 0.20 to 0.21.
The user's own upper's lower corners are cut to flat chamfers over its rear half, from its rear end to a round run-out ahead of the takedown pin (receiver_rear_chamfer_front_x); ahead of that they are the section's own (receiver_lower_corner_w). Their upper edge is the corners' (receiver_lower_corner_y: 0.631; 0.61 in the end view below, 0.65 on the user's side photo). Until 2026-10-05 the model drew the section's rounded corner, 0.134 across, the whole way (the model review).
Receiver: the front end of the rear lower chamfers (where their run-out reaches the underside), X3 in ± 0.06 in 76.2 mmCorroboratedPhoto: the user's own 22RB lying on its left side, its right side square on from 5 to 7 ft; 2026-10-03
Photo 3 in ± 0.06 in used
the user's own 22RB lying on its left side, its right side square on from 5 to 7 ft; 2026-10-03, from the site owner
Scale: the two lug holes' see-through centres (107.4 px/in: the frame the side outline was traced in); the chamfer is on the near side, 0.66 in nearer the lens than they are, and it is read 3 in from the pin. Read by luminance across the lower edge at stations along the receiver: the chamfer is a dark face (13 to 20) under the side flat (47 to 55), its upper edge 0.65 above the pin line from 0.6 to 2.7 in ahead of the pin, 0.635 at 2.8, about 0.50 at 2.9 and gone at 3.0, where the face under the flat is the section's own corner (41 to 49). A quarter round from 2.74 to 2.96 passes through all three, as the lens saw them: the near side reads toward the rear from where it stood, over the upper's middle (0.04 to 0.05 in here, by the 0.08 the charging handle's wing tip reads out in the same photo, 11 in from the lens's axis), so its end is 3.0. ± is the 0.1 in between stations, halved, and that correction's 0.02
Photo 2.95 in ± 0.2 in
the user's own 22RB from below, straight down from 5 to 7 ft; 2026-10-03, from the site owner
Scale: the receiver's own width in the same view (140.5 px = 1.31 in: 107.3 px/in), from the takedown lug's middle (photo x 2437 ± 6). Read by the dark band inside each edge is there at photo x 2140 and behind, and gone at 2100 and ahead, on both sides: its end at 2120 ± 20
Read square on in the frame the outline was traced in, at stations 0.1 in apart; from below it ends at the same place within that view's ±, and the close photo of the right side (e421a9af0aa7) shows the same run-out.
Receiver: the length of the rear lower chamfers' run-out (from their full height to the underside)0.22 in ± 0.06 in 5.6 mmProvisionalPhoto: the user's own 22RB lying on its left side, its right side square on from 5 to 7 ft; 2026-10-03
Photo 0.22 in ± 0.06 in used
the user's own 22RB lying on its left side, its right side square on from 5 to 7 ft; 2026-10-03, from the site owner
Scale: the two lug holes' see-through centres (107.4 px/in: the frame the side outline was traced in). Read by the chamfer's upper edge is at its full height 2.7 in ahead of the pin, 0.015 down at 2.8, about 0.15 down at 2.9 and at the underside by 3.0: a quarter round 0.22 long (2.74 to 2.96 as the lens saw it; receiver_rear_chamfer_front_x has its end with the lens allowed for). The close photo of the right side (e421a9af0aa7) shows its shape: level where it leaves the upper edge, square to the underside where it ends. ± is half the stations' spacing at each end
Receiver: the takedown and pivot lugs' width0.49 in ± 0.015 in 12.4 mmConflictPhoto: the user's own 22RB, the rear end straight on; 2026-10-03
Photo 0.447 in ± 0.02 in
Nordic, looking forward down the receiver from the rear, harvested
Scale: the section's full width, 272 px = the receiver's 1.38 in (width): 197 px/in across. Read by the takedown lug below the rear face, 88 px (px 532 to 620)
Photo 0.49 in ± 0.015 in used
the user's own 22RB, the rear end straight on; 2026-10-03, from the site owner
Scale: the receiver's own width across its side flats in the same view (714.8 px = 1.31 in: width), the lug 0.4 in further from the lens allowed for. Read by the takedown lug across, rows 833.4 to 1097.4 (264.0 px = 0.484 at the receiver's scale)
The user's own upper, straight on; the earlier rear view's 0.447 ± 0.02 is a little under it. It fits the lower's lug slot (.500).
rear and user-rear differ by 0.043 in beyond what each states it is good to.
Inside the lower's lug slot, .500 REF (TDP 8448608).
Receiver bore (the bolt's channel), diameter0.851 in ± 0.03 in 21.6 mmProvisionalPhoto: Nordic, looking forward down the receiver from the rear
Photo 0.851 in ± 0.03 in used
Nordic, looking forward down the receiver from the rear, harvested
Scale: the section's full width, 272 px = the receiver's 1.38 in (width): 197 px/in across. Read by the bore's widest row at the rear face (167.5 px)
Drawn about the bore axis (bore_axis_above_pin). The ejection port opens into it.
Ejection port opening, rear edge, X3.565 in ± 0.02 in 90.6 mmCorroboratedPhoto: Nordic, 18 in 22RB upper, true right side, 4096 px
Photo 3.565 in ± 0.02 in used
Nordic, 18 in 22RB upper, true right side, 4096 px, harvested
Scale: pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane. Read by the opening's rear end on a 4x crop (px 970)
Photo 3.516 in ± 0.06 in
right side, Nordic NC22-16-Upper-V2, harvested
Scale: rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper. Read by the opening's rear end on a 3x crop (px 275)
Twice the resolution and a pin frame in the receiver's plane; the 16 in photo agrees (its ~1.2% short bias allowed for).
Ejection port opening, front edge, X5.283 in ± 0.02 in 134.2 mmConflictPhoto: Nordic, 18 in 22RB upper, true right side, 4096 px
Photo 5.283 in ± 0.02 in used
Nordic, 18 in 22RB upper, true right side, 4096 px, harvested
Scale: pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane. Read by the opening's front end on a 4x crop (px 1210)
Photo 5.193 in ± 0.06 in
right side, Nordic NC22-16-Upper-V2, harvested
Scale: rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper. Read by the opening's front end on a 3x crop (px 362); +1.2% for the photo's bias is 5.255
Twice the resolution and a pin frame in the receiver's plane; the 16 in photo agrees (its ~1.2% short bias allowed for).
18in and 16in differ by 0.09 in beyond what each states it is good to.
Ejection port opening, bottom edge, Y0.833 in ± 0.02 in 21.2 mmCorroboratedPhoto: Nordic, 18 in 22RB upper, true right side, 4096 px
Photo 0.833 in ± 0.02 in used
Nordic, 18 in 22RB upper, true right side, 4096 px, harvested
Scale: pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane. Read by the opening's bottom on a 4x crop (py 1219)
Photo 0.837 in ± 0.06 in
right side, Nordic NC22-16-Upper-V2, harvested
Scale: rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper. Read by on a 3x crop (py 432)
Twice the resolution and a pin frame in the receiver's plane; the 16 in photo agrees (its ~1.2% short bias allowed for).
Ejection port opening, top edge, Y1.309 in ± 0.02 in 33.2 mmCorroboratedPhoto: Nordic, 18 in 22RB upper, true right side, 4096 px
Photo 1.309 in ± 0.02 in used
Nordic, 18 in 22RB upper, true right side, 4096 px, harvested
Scale: pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane. Read by the opening's top on a 4x crop (py 1152.5): the bolt shows from 1.27 down
Photo 1.376 in ± 0.06 in
right side, Nordic NC22-16-Upper-V2, harvested
Scale: rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper. Read by on a 3x crop (py 404)
Twice the resolution and a pin frame in the receiver's plane; the 16 in photo agrees (its ~1.2% short bias allowed for).
Ejection port opening, corner radius0.063 in ± 0.015 in 1.6 mmProvisionalPhoto: Nordic, 18 in 22RB upper, true right side, 4096 px
Photo 0.063 in ± 0.015 in used
Nordic, 18 in 22RB upper, true right side, 4096 px, harvested
Scale: pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane. Read by the opening's corner arcs on a 4x crop (~9 px)
Ejection port pocket (the milled recess around the opening), rear edge, X3.529 in ± 0.02 in 89.6 mmConflictPhoto: Nordic, 18 in 22RB upper, true right side, 4096 px
Photo 3.529 in ± 0.02 in used
Nordic, 18 in 22RB upper, true right side, 4096 px, harvested
Scale: pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane. Read by the recess's rear end on a 4x crop (px 965)
Photo 3.421 in ± 0.06 in
right side, Nordic NC22-16-Upper-V2, harvested
Scale: rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper. Read by on a 3x crop (px 270)
Twice the resolution and a pin frame in the receiver's plane; the 16 in photo agrees (its ~1.2% short bias allowed for).
18in and 16in differ by 0.108 in beyond what each states it is good to.
Ejection port pocket, front edge, X5.326 in ± 0.02 in 135.3 mmCorroboratedPhoto: Nordic, 18 in 22RB upper, true right side, 4096 px
Photo 5.326 in ± 0.02 in used
Nordic, 18 in 22RB upper, true right side, 4096 px, harvested
Scale: pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane. Read by the recess's front end on a 4x crop (px 1216)
Photo 5.271 in ± 0.06 in
right side, Nordic NC22-16-Upper-V2, harvested
Scale: rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper. Read by on a 3x crop (px 366); +1.2% for the photo's bias is 5.334
Twice the resolution and a pin frame in the receiver's plane; the 16 in photo agrees (its ~1.2% short bias allowed for).
Ejection port pocket, bottom edge, Y0.811 in ± 0.02 in 20.6 mmCorroboratedPhoto: Nordic, 18 in 22RB upper, true right side, 4096 px
Photo 0.811 in ± 0.02 in used
Nordic, 18 in 22RB upper, true right side, 4096 px, harvested
Scale: pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane. Read by on a 4x crop (py 1222)
Photo 0.798 in ± 0.06 in
right side, Nordic NC22-16-Upper-V2, harvested
Scale: rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper. Read by on a 3x crop (py 434)
Twice the resolution and a pin frame in the receiver's plane; the 16 in photo agrees (its ~1.2% short bias allowed for).
Ejection port pocket, top edge, Y (where it runs out on the upper chamfer)1.452 in ± 0.02 in 36.9 mmCorroboratedPhoto: Nordic, 18 in 22RB upper, true right side, 4096 px
Photo 1.452 in ± 0.02 in used
Nordic, 18 in 22RB upper, true right side, 4096 px, harvested
Scale: pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane. Read by on a 4x crop (py 1132.5)
Photo 1.414 in ± 0.06 in
right side, Nordic NC22-16-Upper-V2, harvested
Scale: rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0; 52.0 px/in at the receiver; reads ~1.2% short along the upper. Read by on a 3x crop (py 402)
Twice the resolution and a pin frame in the receiver's plane; the 16 in photo agrees (its ~1.2% short bias allowed for).
Ejection port pocket, corner radius0.16 in ± 0.03 in 4.1 mmProvisionalPhoto: Nordic, 18 in 22RB upper, true right side, 4096 px
Photo 0.16 in ± 0.03 in used
Nordic, 18 in 22RB upper, true right side, 4096 px, harvested
Scale: pin frame from the upper's lug holes picked on 8x crops: takedown (472, 1335.3), pivot (1362.4, 1334.4) = (0, 0), (6.375, 0): 139.7 px/in, the lugs in the receiver's plane. Read by the recess's corner arcs on a 4x crop (~22 px)
Ejection port pocket depth (its flat floor below the receiver's side)0.232 in ± 0.03 in 5.9 mmProvisionalPhoto: Aawee: the NCT3 handguard, straight end-on: the section the receiver shares
Photo 0.232 in ± 0.03 in used
Aawee: the NCT3 handguard, straight end-on: the section the receiver shares, harvested
Scale: the section's scale as traced (profiles.front, its height the handguard's), placed on the bore. Read by the side flat's half-width (0.801) less the section's half-width at the pocket's top edge, 1.452 above the pin line (0.569)
A flat-floored recess's outline runs out on the section's upper face where that face comes down to its floor: its top edge (1.452) gives the depth through the section. Since 2026-10-02 the section is the handguard's (the owner: the two match); the old section's chamfer gave 0.23 the same way.
Bolt catch relief (an arch cut in the receiver's lower left edge), rear foot, X2.555 in ± 0.03 in 64.9 mmProvisionalPhoto: left side, NC22RB-UPPER-16-KIT_3_HR
Photo 2.555 in ± 0.03 in used
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0; 84 px/in. Read by the arch's rear foot on a 5x crop with frame gridlines
Bolt catch relief, front foot, X3.473 in ± 0.03 in 88.2 mmProvisionalPhoto: left side, NC22RB-UPPER-16-KIT_3_HR
Photo 3.473 in ± 0.03 in used
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0; 84 px/in. Read by the arch's front foot on the same crop
Bolt catch relief, top, Y0.6 in ± 0.03 in 15.2 mmProvisionalPhoto: left side, NC22RB-UPPER-16-KIT_3_HR
Photo 0.6 in ± 0.03 in used
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0; 84 px/in. Read by the arch's crown on the same crop (its peak near x 3.02)
Handguard's underside (its bottom flat), Y0.076 in ± 0.02 in 1.9 mmProvisionalWorked out: {.handguard_center_y} - {.handguard_width} / 2
Worked out 0.051 in ± 0.07 in
{.rail_top_above_pin} - 2.039in, harvested
The receiver's rail top less the side photos' height (handguard_height's `flatlay` and `right-photo`, 2.039 and 2.038): what was drawn until 2026-10-02.
Worked out 0.0765 in ± 0.02 in used
{.handguard_center_y} - {.handguard_width} / 2, harvested
Half the width across the flats below the handguard's centre, which is on the barrel's axis.
The handguard is centred on the barrel (measured: handguard_above_barrel), and its section is as tall below its centre as it is wide across the flats. The right photo's underside (0.088) and the end view's height under the handguard's rail (0.091) agree within 0.01; the older figure rested on a rail top the side photos read 0.05 high.
Where the handguard's end section (profiles.front, traced from the NCT3's end view) sits. Until 2026-10-02 it was the receiver's rail top less the handguard's side-view height (0.03), which put the handguard's bore 0.047 in below the barrel (M6's review, finding 29). The side photos read the handguard's rail top 0.05 high along its length (a trend the lens gives: handguard_rail_step), so a height hung from the true rail top came out that much low. Three readings that don't use that height agree on 0.08 to 0.09: the barrel's axis (handguard_above_barrel), the right photo's own underside in its pin frame (0.088, profiles.side), and the handguard's rail top less the end view's height (2.062 − 1.971 = 0.091).
Handguard width (Z), across the side flats1.602 in ± 0.004 in 40.7 mmConflictWorked out: {.handguard_od}
Photo 1.45 in ± 0.09 in
a different length/model of Nordic 22 upper, same-family handguard per the user; supplied in chat, from the site owner
Scale: the top rail's front end, 0.835 in wide (std.picatinny.top_width), in the same plane as the handguard's front face. Read by front-face width over rail-head width, both measured horizontally in the face plane (≈225 px / 130 px); the far side's widest point is partly hidden by the barrel, so this may read slightly low
Worked out 1.602 in ± 0.004 in used
{.handguard_od}, harvested
The NCT3's listed 40.7 mm, across the side flats (handguard_od's note).
Photo 1.653 in ± 0.06 in
Aawee: the NCT3 handguard, straight end-on, transparent background, harvested
Scale: nordic-22rb-upper.handguard_height (2.04 ± 0.058, the 22RB's side photos), the same section's bottom flat to rail top. Read by outer silhouette 320 px across the side flats (rows 360–390) over 395 px bottom flat to rail top (rows 149–543), × 2.04; ± is the height's (the near face is one plane; the rail's end may sit a little behind it)
Photo 1.605 in ± 0.015 in
the user's own 22RB, the muzzle end straight on, the rail at the bottom, a tape across above; 2026-10-03); a copy on file (the user's own 22RB from below and from above, straight down from 5 to 7 ft; 2026-10-03, from the site owner
Scale: the rail head's widest row end on (473 and 475 px = 0.835, carried 0.085 in nearer to the octagon's plane); the rail's pitch and the M-LOK pitch from above and below. Read by across the side flats: 1.61 to 1.62 end on (921 and 923 px; the rail head's sharp corners lose a pixel or two to blur, which makes it 0.5% large), 1.58 to 1.60 from above and below
A listed figure for the handguard family sold as the original's, read across the flats as its own end view shows; the end view's proportions with the 22RB's height agree (1.65 ± 0.06). The sister model's 1.45 came from a 3/4 view.
photo-sister and nct3-od differ by 0.152 in beyond what each states it is good to.
photo-sister and end-ratio differ by 0.203 in beyond what each states it is good to.
photo-sister and user differ by 0.155 in beyond what each states it is good to.
No Nordic figure for the 22RB's handguard. The NCT3 (the handguard family Aawee sells as the original's) is listed at 40.7 mm outer diameter, which its straight end view shows to be across the side flats (handguard_od); the end view's width-to-height ratio with the 22RB's side-view height agrees. A sister model's 3/4 shot gave 1.45 (M2): read as a ratio to the rail head's width in a view that foreshortens the body more than the rail's narrow front face, it reads low, and stays as a visible conflict. The user found about 1.6 in OD quoted online (2026-09-30, link not recorded), which this matches.
Receiver width across its side flats (Z), behind the flare to the handguard1.31 in ± 0.02 in 33.3 mmConflictPhoto: the user's own 22RB from below and from above, straight down from 5 to 7 ft; 2026-10-03
Photo 1.38 in ± 0.08 in
Nordic, looking forward down the receiver from the rear, harvested
Scale: the rail's recoil grooves span the full 0.835 in head (std.picatinny.top_width) on the same image rows as the body's silhouette. Read by body silhouette width over groove length on the same rows (1.28–1.35 in raw across rows 500–560, ≈160 px grooves). The body's widest line sits ~1 in below the rail top, so it's ~1.5 in farther from the camera; the receiver's own taper along the photo (~3.5%/in) puts it ~5% too small. Corrected ≈1.34–1.42 in.
Worked out 1.602 in ± 0.06 in
{.handguard_width}, from the site owner
The handguard's width across its side flats, as the user says the receiver's section matches the handguard's (2026-10-02).
Photo 1.31 in ± 0.02 in used
the user's own 22RB from below and from above, straight down from 5 to 7 ft; 2026-10-03, from the site owner
Scale: the handguard's width in the same views (1.602, the listing's; 1.58 to 1.60 by the rail's pitch and the M-LOK pitch). Read by the receiver across its side flats against the handguard across its own: 138.6 to 140.6 px against 169.8 to 171.1 from below (0.82), 138.4 to 139.8 against 167.6 to 168.6 from above (0.83). The body widens from one to the other over its last 0.4 in, behind the seam (receiver_flare_start_x)
The user's own upper from above and from below. Its owner's "the cross section of the upper receiver seems to match up very closely to the cross section on the handguard" is the seam, where the receiver has flared to the handguard's section; behind the flare it is 0.82 of it. The earlier rear view's 1.38 ± 0.08 agrees.
rear-top and owner differ by 0.222 in beyond what each states it is good to.
owner and user differ by 0.292 in beyond what each states it is good to.
Nordic's parts list calls it an extruded receiver (constant cross-section). The user, who owns the upper (2026-10-02): "the receiver and hard guard come together nearly along a nearly imperceptible seam. The cross section of the upper receiver seems to match up very closely to the cross section on the handguard on the real thing." So its section is the handguard's, and its width the handguard's across the flats. The rear view's reading, taken looking down the receiver with the body's widest line 1.5 in further away than the rail it was scaled by, stays as the conflict it is.
Where the receiver begins to widen to the handguard's section, X6.19 in ± 0.05 in 157.2 mmCorroboratedPhoto: the user's own 22RB from below, straight down; 2026-10-03
Photo 6.19 in ± 0.05 in used
the user's own 22RB from below, straight down; 2026-10-03, from the site owner
Scale: the handguard's rearmost M-LOK slot in the same view (its opening 9.23 to 10.15 through the side photos' pose: 110.6 px/in). Read by the body's two edges turn outward at strip px 815 and reach the handguard's width at 858: 6.19 to 6.58, the seam (handguard_rear_x). ± is a 5 px pick on a dark edge over shadow
Photo 6.22 in ± 0.04 in
the user's own 22RB, close on the seam from its left; 2026-10-04, from the site owner
Scale: the rail's own slots beside it in the same view: 250 px a pitch (std.picatinny.slot_pitch) just behind the seam and 270 just ahead of it. Read by the facet that brings the receiver out to the handguard's upper diagonal is a triangle in that diagonal's plane, its base on the seam and its point on the rail neck's line 240 px behind it: 0.38 in (0.36 to 0.39 by which pitch); less than the seam (handguard_rear_x)
Read from below, square on, with a scale in the same plane; the close photo, at its own rail's pitch, has the facet's point 0.03 in nearer the seam, within both.
How the receiver widens, from the user's close photo of the seam (584c3ded24e1): its own faces run straight on, and each face of the handguard's section comes back over it as a flat facet, a triangle with its base on the seam and its point this far behind it. The rail's break is the same line as the body's seam: the receiver's last tooth ends on it and the handguard begins with a slot.
Charging handle's T, side to side1.97 in ± 0.02 in 50 mmProvisionalPhoto: the user's own 22RB: the T from above, close and far, and from behind; 2026-10-03
Photo 1.97 in ± 0.02 in used
the user's own 22RB: the T from above, close and far, and from behind; 2026-10-03, from the site owner
Scale: the rail's pitch beside it (154.75 px a slot: 393 px/in) in the close photo; the rail's slots in the far one; the receiver's width in the rear view. Read by the T from end to end: 1.967 (773 px, rows 866.9 to 1640.2), 1.98 (216 px at 109.2 px/in), 1.97 (1086.5 px, 0.23 in nearer the lens allowed for)
0.13 under an AR-pattern T on file (std.ar15.charging_handle_t_width, 2.1 ± 0.05), which the model drew it at.
Charging handle's T, front to back (its wings, either side of the rail)0.496 in ± 0.02 in 12.6 mmProvisionalPhoto: the user's own 22RB: the receiver's rear end from above, close, the T in the middle of the frame; 2026-10-03
Photo 0.496 in ± 0.02 in used
the user's own 22RB: the receiver's rear end from above, close, the T in the middle of the frame; 2026-10-03, from the site owner
Scale: the T's own width in the same view and the same plane (charging_handle_t_width, 1.97): 775 px from end to end (columns 940 to 980: 773.7, 777.4, 772.6), 393 px/in, which is also the rail's pitch beside it (154.75 px a slot). Read by the right wing where it stands clear of the receiver over the floor, front face to rear face along rows 980 and 1000: 193.7 and 195.8 px at luminance 80, 194.3 at 110 (195 px). ± is 3 px at each edge of a matte black part on a bright floor (0.015) and the width's own ± carried over (0.005). The left wing carries the latch, which stands further forward, and isn't read
With rear_behind_pin (the T's rear face) this puts the wings' front faces 0.36 in behind the takedown pin: the T stands astride the receiver's rear face (std.ar15.upper_rear_face_x), 0.24 in of it behind the face and the rest either side of the rail's solid rear end, whose round nose is nested in it. Seen from above the T is a stadium: its two ends are full rounds (the chord across the right wing 35.5, 55.5 and 75.5 px in from its end is 150.0, 174.4 and 187.7 px; a half round of the T's own depth has 150.5, 176.0 and 190.0). Until 2026-10-05 the model drew only what lies behind the rear face, square: half as deep (the model review, 2026-10-05).
The charging handle's T: its top above the pin line2.047 in ± 0.012 in 52 mmProvisionalPhoto: the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05
Photo 2.047 in ± 0.012 in used
the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05, from the site owner
Scale: the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how). Read by the T's top at its left end 20.7 px (0.043 in) under the rail's top line at columns 2440 and 2480; less than rail_top_above_pin by that. ± is 4 px and the rail top's own
The T's top is a little under the rail's, 0.04 in: from behind, the rail's tongue shows over it. With charging_handle_t_bottom_y the T is 0.45 in tall; the rear view straight on has 0.43 between its top and its rear face's lower edge, which is the upper edge of a chamfer along its underside.
The charging handle's T: the upper side of the slot across its left end, above the pin line1.846 in ± 0.012 in 46.9 mmProvisionalPhoto: the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05
Photo 1.846 in ± 0.012 in used
the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05, from the site owner
Scale: the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how). Read by the upper block's underside at the T's left end, 117 px (0.244 in) under the rail's top line at columns 2440 and 2480 (rows 639.5 and 640.9)
The T's left end is sawn across, front to back: a block 0.20 in thick above, a jaw 0.10 below, and the latch's tail in the slot between (0.147 in, charging_handle_slot_bottom_y). The rear view straight on has the same three: 0.20, 0.12 and the jaw's rear face.
The charging handle's T: the lower side of the slot across its left end, above the pin line1.699 in ± 0.012 in 43.2 mmProvisionalPhoto: the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05
Photo 1.699 in ± 0.012 in used
the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05, from the site owner
Scale: the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how). Read by the lower jaw's top at the T's left end, 187.8 px (0.391 in) under the rail's top line at column 2480 (row 710.1)
The charging handle's T: the slot across its left end, from that end to where it stops0.81 in ± 0.02 in 20.6 mmProvisionalPhoto: the user's own 22RB: the rear end straight on, close, the upper standing on its muzzle; 2026-10-05
Photo 0.81 in ± 0.02 in used
the user's own 22RB: the rear end straight on, close, the upper standing on its muzzle; 2026-10-05, from the site owner
Scale: the T's own width in the plane of its rear face (charging_handle_t_width: 1670.3 px end to end, 848 px/in). Read by the slot in the rear face from the T's left end (column 145.9) to its end behind the latch's spring (the spring's coils at columns 758 to 819, the slot's end at 835): 689 px. ± is where the slot's end is behind the coils
Seen from behind the slot is open at the T's left end and runs 0.81 in toward the middle: the latch's tail, then its spring, coiled across the slot.
The charging handle's T: the round recess in its front for the rail's nose, radius0.455 in ± 0.02 in 11.6 mmProvisionalPhoto: the user's own 22RB: the receiver's rear end from above, close, the handle home; 2026-10-05
Photo 0.455 in ± 0.02 in used
the user's own 22RB: the receiver's rear end from above, close, the handle home; 2026-10-05, from the site owner
Scale: the T's own width in the rail's plane (charging_handle_t_width: 1318.4 px, 669 px/in); a tooth's top flat (437.7 px for the standard's 0.656: 667) and slot 0's front wall (1.755 in ahead of the T's rear face for the ledger's 1.758) agree. Read by the recess's wall at the T's top: on the centre line 99 px ahead of the T's rear face, and at the T's front face a chord 584 px across: a circle of 297.6 px (0.446 in). The handle out of the upper from above (c8a014aa1043, at its own T's width: 635 px/in) has the same wall 0.169 in ahead of the rear face and a chord of 0.895 in at the front face: 0.465. The middle of the two; ± covers both
From above the T's front is cut round for the rail's nose: a circle wider than the nose (rail_tongue_width), its centre ahead of the T's front face, down to the level the handle's plate is at (charging_handle_plate_top_y). Until 2026-10-05 the model cut it square.
The charging handle's T: what is left of it behind the round recess, on the centre line0.155 in ± 0.015 in 3.9 mmProvisionalPhoto: the user's own 22RB: the receiver's rear end from above, close, the handle home; 2026-10-05
Photo 0.155 in ± 0.015 in used
the user's own 22RB: the receiver's rear end from above, close, the handle home; 2026-10-05, from the site owner
Scale: the T's own width in the rail's plane (charging_handle_t_width: 1318.4 px, 669 px/in); a tooth's top flat (437.7 px for the standard's 0.656: 667) and slot 0's front wall (1.755 in ahead of the T's rear face for the ledger's 1.758) agree. Read by the T's rear face to the recess's wall on the centre line: 99.2 px (0.148 in); 0.169 on the handle out of the upper (c8a014aa1043). ± covers both
The charging handle: the top of its plate ahead of the T, above the pin line1.89 in ± 0.015 in 48 mmProvisionalPhoto: the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05
Photo 1.89 in ± 0.015 in used
the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05, from the site owner
Scale: the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how). Read by the plate's left edge under the rail's tongue: its top 8 px under the tongue's underside (row 619.9 at column 2150; the tongue's underside 611.5), 0.203 in under the rail's top line. The handle out of the upper from its side (ee68cec1e113) has the plate's top 0.145 in under the T's: 1.90
Ahead of the T the handle is a plate a step lower than the T's top, as wide as the rail's tongue where it enters the receiver and flared out to the T's front face (profiles.handle). The rail's tongue stands over it; the round recess in the T is cut down to it.
The charging handle's latch: how thick it is, top to bottom0.124 in ± 0.012 in 3.1 mmProvisionalPhoto: the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05
Photo 0.124 in ± 0.012 in used
the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05, from the site owner
Scale: the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how). Read by the latch's arm where its end stands in the receiver's window, its lit side face between rows 659.5 and 718.2 at column 1937: 58.7 px at the rail's 472 px/in; 0.125 at column 2200 (rows 655 to 715)
The latch is a flat piece lying in the T's slot (charging_handle_slot_top_y, charging_handle_slot_bottom_y): its pad at the T's left end, its arm forward along the receiver to a tooth that points inward (profiles.handle, the feature `latch`).
The rail's rear end behind the standard's head: the tongue, side to side0.64 in ± 0.015 in 16.3 mmProvisionalPhoto: the user's own 22RB: the receiver's rear end from above, close, the handle home; 2026-10-05
Photo 0.64 in ± 0.015 in used
the user's own 22RB: the receiver's rear end from above, close, the handle home; 2026-10-05, from the site owner
Scale: the T's own width in the rail's plane (charging_handle_t_width: 1318.4 px, 669 px/in); a tooth's top flat (437.7 px for the standard's 0.656: 667) and slot 0's front wall (1.755 in ahead of the T's rear face for the ledger's 1.758) agree. Read by the tongue from above between its two upright sides: 416 to 425 px at columns 1000 and 1350 (0.625 to 0.64 at 667 px/in), the lower side's edge under its own shadow; its edges broken 0.03 to 0.045 in. A tooth's top flat in the same view is 0.656 (the standard's)
From rail_rear_x back the rail has no shoulders: a tongue as wide as the rail's top flat, its sides upright, its rear end a half round nested in the T's recess. It stands over the charging handle's plate (rail_tongue_bottom_y), which is how the handle gets into the receiver.
The rail's tongue: its round nose's rearmost point, X-0.684 in ± 0.02 in -17.4 mmProvisionalPhoto: the user's own 22RB: the receiver's rear end from above, close, the handle home; 2026-10-05
Photo -0.684 in ± 0.02 in used
the user's own 22RB: the receiver's rear end from above, close, the handle home; 2026-10-05, from the site owner
Scale: the T's own width in the rail's plane (charging_handle_t_width: 1318.4 px, 669 px/in); a tooth's top flat (437.7 px for the standard's 0.656: 667) and slot 0's front wall (1.755 in ahead of the T's rear face for the ledger's 1.758) agree. Read by the nose's outline on the centre line, 118.3 px ahead of the T's rear face (column 679.1), less rear_behind_pin; its top flat's own round ends 0.097 in ahead of that (column 743.8). The nose is a half round of the tongue's width: its straight sides begin 0.31 in ahead of its tip
The rail's tongue: its underside above the pin line, where it stands over the charging handle's plate1.905 in ± 0.012 in 48.4 mmProvisionalPhoto: the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05
Photo 1.905 in ± 0.012 in used
the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05, from the site owner
Scale: the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how). Read by the tongue's lower edge from the left, a straight line from the latch's window back to the T: 87.4 px (0.185 in) under the rail's top line at column 2150 (row 611.5)
The receiver's window for the charging handle's latch, on its left: its front end, X0.446 in ± 0.015 in 11.3 mmProvisionalPhoto: the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05
Photo 0.446 in ± 0.015 in used
the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05, from the site owner
Scale: the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how). Read by the window's front edge at column 1890 (its wall's shadow to 1909.6): 115.9 px behind slot 0's rear wall (column 1774.1, the ledger's 0.692)
On the receiver's left, under the rail, an upright window with round ends is cut into the wall: the latch's arm lies along the receiver to it and its tooth drops in. Seen square on from the left; how deep it is cut isn't read (the model cuts it to the latch's tooth and a clearance).
The receiver's window for the charging handle's latch: its rear end, X0.245 in ± 0.015 in 6.2 mmProvisionalPhoto: the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05
Photo 0.245 in ± 0.015 in used
the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05, from the site owner
Scale: the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how). Read by the window's rear edge at column 1985 between rows 620 and 700
The receiver's window for the charging handle's latch: its top, above the pin line1.949 in ± 0.012 in 49.5 mmProvisionalPhoto: the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05
Photo 1.949 in ± 0.012 in used
the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05, from the site owner
Scale: the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how). Read by the inner edge of the window's upper round at column 1937 (row 591.8), 66.4 px under the rail's top line
The receiver's window for the charging handle's latch: its bottom, above the pin line1.585 in ± 0.012 in 40.3 mmProvisionalPhoto: the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05
Photo 1.585 in ± 0.012 in used
the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05, from the site owner
Scale: the rail's pitch in the same view (472 px/in over ten slots) and 480 px/in at the T's end, 0.57 in nearer a lens 35 in or more away (charging_handle_t_bottom_y's reading says how). Read by the window's lower round at column 1937 (row 763.5), 238.2 px under the rail's top line
Handguard: the fine groove engraved each side of every M-LOK row, from the row's centre line0.21 in ± 0.012 in 5.3 mmProvisionalPhoto: the user's own 22RB: the receiver's underside and the handguard's rear from below, close; 2026-10-05
Photo 0.21 in ± 0.012 in used
the user's own 22RB: the receiver's underside and the handguard's rear from below, close; 2026-10-05, from the site owner
Scale: the M-LOK slots in the same face: their rear ends 268.7 px apart for the standard's 40 mm (std.mlok.slot_pitch: 170.6 px/in), a slot's own width 47 px for its 7 mm. Read by the dark line each side of the row on the bottom face, from the slot's middle (row 983.4): 33.6, 35.2 and 36.6 px above it and 38.4 below at columns 1860, 1900 and 1980. The close view of the seam from the right (74a0161414d1, the rail's pitch 408 px/in) has the side face's two 169 px apart: 0.207 each. ± covers the four and 2 px
The user, 2026-10-05: "can we add some of the detailing on the Nordic upper (eg. Those engraved lines on the upper)". Every face that has a row of M-LOK slots has a fine groove along each side of it, the same distance off on each face: on the right side the side faces two are 0.414 in apart and the upper diagonals 0.357 as that face is seen from the side. A second line outside each, in the view from below, is the faces own edge (the flats corner, 0.27 out on the bottom face), not a groove.
Handguard: the engraved grooves, across0.044 in ± 0.008 in 1.1 mmProvisionalPhoto: the user's own 22RB: the receiver's right side around the ejection port, square on, the seam and the handguard's rear in frame; 2026-10-05
Photo 0.044 in ± 0.008 in used
the user's own 22RB: the receiver's right side around the ejection port, square on, the seam and the handguard's rear in frame; 2026-10-05, from the site owner
Scale: the rail's pitch in the same view (twelve teeth 160.9 px apart: 408 px/in); the side face is 0.4 in nearer the lens than the rail's edge. Read by down column 2450, the two grooves that are clear of a face's corner: the upper diagonal's upper one from its lit rim to the far side of its shadow (rows 777.1 to 795.6: 18.5 px) and the side face's upper one (990.4 to 1007.8: 17.4 px): 0.045 and 0.043. From below (0dfba70ae389, 170.6 px/in) the shadowed wall alone is 3.7 to 4 px: half of it. ± is 3 px
A round-bottomed groove: from the right and close, each is a lit wall beside a shadowed one. The first reading took the shadowed wall alone for the groove (3.7 to 4 px from below, 0.022 in) and the model drew hairlines; the user, seeing them: "Those lines dont look very good". How deep they are cut isnt read (drawn a third as deep as they are wide, round-bottomed, their ends tapering out as the close view has them).
Handguard: how far the engraved grooves run past the ends of the slots they lie beside0.3 in ± 0.04 in 7.6 mmProvisionalPhoto: the user's own 22RB: the receiver's underside and the handguard's rear from below, close; 2026-10-05
Photo 0.3 in ± 0.04 in used
the user's own 22RB: the receiver's underside and the handguard's rear from below, close; 2026-10-05, from the site owner
Scale: the M-LOK slots in the same face (170.6 px/in by their pitch). Read by the upper groove's pointed rear end on the bottom face (columns 1737 to 1748 along row 948) behind the short slot's rear end (column 1793.8): 46 to 57 px
On the bottom face and the two faces either side of it the grooves begin this far behind the rearmost (short) slot; on every face they end about as far ahead of the foremost (0.26 in on the right side from 5 ft, d633f1bf49ff, at 107 px/in: within this). On the two sides and the two upper faces they begin near the seam instead (handguard_groove_upper_rear_x).
Handguard: where the engraved grooves begin on its two sides and its two upper faces, X6.82 in ± 0.04 in 173.2 mmProvisionalPhoto: the user's own 22RB: the receiver's right side around the ejection port, square on, the seam and the handguard's rear in frame; 2026-10-05
Photo 6.82 in ± 0.04 in used
the user's own 22RB: the receiver's right side around the ejection port, square on, the seam and the handguard's rear in frame; 2026-10-05, from the site owner
Scale: the rail's pitch in the same view (twelve teeth 160.9 px apart: 408 px/in) and the seam itself (column 2145, handguard_rear_x). Read by the grooves' pointed rear ends on the side face, 88 to 90 px ahead of the seam (column 2233): 0.22 in, more than handguard_rear_x by that. ± is where a point ends (10 px) and the side face being 0.4 in nearer the lens than the rail's edge
On the sides and the upper diagonals the grooves run back past the first slot, under Nordic's name and the M-LOK mark, to a pointed end just ahead of the seam.
Receiver: the takedown and pivot lugs' pin holes0.251 in ± 0.001 in 6.4 mmConfirmedStandard: US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.250 DIA +.002 THRU (the takedown lug's, CSK .31 DIA X 90 INCL THIS SIDE ONLY); .250 DIA +.001 THRU (the pivot lug's)” used
US Army TDP drawing 8448524 (Receiver, Upper), sheet 1 of 2, rev G: side elevation; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Photo 0.257 in ± 0.008 in
the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05, from the site owner
Scale: the rail's pitch in the same view (472 px/in at the rail's near edge; 470 at the lug's face, 0.19 in further from a lens 35 in or more away). Read by the takedown lug's hole against the floor, top to bottom (column 2104: rows 1456.2 to 1577.0, 120.8 px). Its near rim, which the drawing countersinks on one side
The standard the lugs are made to: they take a lower's .250 pins. The photo reads the hole's near rim, 0.006 in more, within its own ±.
The user, 2026-10-05: "Did you add the holes in the two pins on the upper receiver?" They were not in the model: the traced outline fills them. The lugs take a lowers .250 pins.
The handguard's centre (the octagon's, and the bore's) above the pin line0.877 in ± 0.017 in 22.3 mmCorroboratedWorked out: {.bore_axis_above_pin} + {.handguard_above_barrel}
Worked out 0.852 in ± 0.07 in
{.rail_top_above_pin} - 2.039in + {.handguard_width} / 2, from the site owner
A regular octagon half its width above a bottom flat hung from the receiver's rail top by the side photos' height (2.039): where the bore and the M-LOK faces were centred from M5 to 2026-10-02, 0.047 below the bore axis (0.8775).
Worked out 0.8775 in ± 0.017 in used
{.bore_axis_above_pin} + {.handguard_above_barrel}, harvested
The barrel's axis, and what the right photo reads the handguard's centre to stand above it.
Measured against the barrel in the one side photo that is level (handguard_above_barrel): the handguard is centred on it within 0.015 in. The older figure put it 0.047 below, which showed on looking into the handguard's mouth; it mixed the standard's bore height with a handguard height read against a rail top the lens raised.
Handguard's centre above the barrel's axis0 in ± 0.012 in 0 mmCorroboratedPhoto: the user's own 22RB, left and right side, square on from 5 to 7 ft; 2026-10-03
Photo 0.009 in ± 0.015 in
right side, Nordic NC22-16-Upper-V2, 1200 px, harvested
Scale: the photo's rail model (02-24d592636074.calib.json) for the last step only, 0.0200 in/px across at the muzzle end; the comparison is between rows. Read by the handguard's centre as the midpoint of the two rows of through-slots (the upper and lower diagonal faces' slots, each seen through to the white ground: rows crossing the 50% level, 84 columns from px 560 to 1077; a line fitted, 0.12 px rms, which carries the photo's 0.44° tilt) against the barrel's axis (the mean of its two edges at their own 50% level, 34 columns of bare barrel at px 1112–1145: row 424.40, quartiles 424.39 and 424.45), the line read at the barrel's columns: 423.95, so 0.45 px above the axis. ± is half a pixel for each of the two readings and what one degree of elevation would move the slots' rows
The user's own upper, photographed from the muzzle end (d98f75b9de4f, 2026-10-02), shows the barrel in the middle of the handguard's mouth: no scale in it, and the muzzle stands nearer the lens than the handguard, so it corroborates and isn't a second measurement. Checks in the same photo: the barrel's axis is 39.2 px above the handguard's underside, 0.785 to 0.805 in by the scale taken (half of 1.602 is 0.801); and of the way from the underside to the rail's tooth tops the axis stands at 0.396, where the drawing until now had the barrel at 0.417 and the handguard's centre at 0.394.
Photo 0 in ± 0.012 in used
the user's own 22RB, left and right side, square on from 5 to 7 ft; 2026-10-03, from the site owner
Scale: the rail's 49 slots and the two lug holes in one fitted camera pose (rail_slot0_x#user). Read by the handguard's underside is 0.80 below the thread protector's axis in both photos (the underside 0.074 to 0.083 and 0.063 to 0.073 above the pins, the axis 0.864 to 0.874): half its width across the flats, so its octagon is centred on the barrel
The user's own upper, both sides, square on. The right product photo's 0.009 ± 0.015 agrees.
Whether the handguard is centred on the barrel, read where both show: at the handguard's front in the right-side photo, which is level (its receiver lands on the lower's deck and on the rail top; the slots of the two diagonal faces show through to the background as two rows the same distance above and below the side face's). Nothing here uses a scale across the photo but the last step to inches, and the rail and the pins aren't in it.
Receiver rail's front end (the front face of its last tooth), X6.597 in ± 0.036 in 167.6 mmConflictWorked out: {.handguard_rail_slot0_x} - {std.picatinny.slot_width} / 2 - {.receiver_rail_last_tooth_deficit}
Photo 6.47 in ± 0.035 in
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0. Read by the tooth's front face where it meets the rail's lower edge, at x 1305.75 ± 1 px over rows 925–945 on a 16× gridded crop, against the seam's own pick on the body below it (1305 ± 1.5 px over rows 940–1040, handguard_rear_x). One line within a pixel, so the seam's value; ± is the seam's
Worked out 6.602 in ± 0.035 in
{.rail_slot0_x} + 15 * {std.picatinny.slot_pitch} - {std.picatinny.slot_width} / 2, harvested
Where slot 15's rear edge is by the slot grid at the standard's slot width; ± is the first slot's.
Worked out 6.597 in ± 0.036 in used
{.handguard_rail_slot0_x} - {std.picatinny.slot_width} / 2 - {.receiver_rail_last_tooth_deficit}, from the site owner
The rear edge of the handguard's first slot by the slot grid, less what the tooth behind it measures narrow (receiver_rail_last_tooth_deficit, from the user's own upper seen from above): the tooth's front face.
The receiver's rail ends with a whole tooth, measured against its neighbours on the user's own upper (two frames, within 0.005 in), and the slots are where the optics are indexed: so its front face is the slot grid's. The side photos put that face on the seam's line within a pixel; the seam's own reading there (6.47 on the near wall, 6.49 carried to the rail's plane) agrees within its ±, and drew the tooth 0.05 and 0.03 in narrow.
left and grid differ by 0.132 in beyond what each states it is good to.
left and whole-tooth differ by 0.127 in beyond what each states it is good to.
The receiver's rail ends with a whole tooth, the one between slots 14 and 15, whose front face is the receiver's front face: in the left photo (16× gridded crop, x 1262–1352, rows 884–944) the seam's line on the body runs up into that tooth's front face without a jog, and the slot ahead of it is cut in the handguard. By the slot grid at the standard's slot width the same face would be 0.05 further forward: the seam is read on the receiver's near wall, 0.80 in nearer the lens than the rail's mid-plane (half the receiver's width), which from this lens (about 100 in away: the teeth's silhouettes widen by 0.0069 in per inch off its axis, at px 1005) reads about 0.03 short; and the 22RB's slots measure 0.226 wide on the lens's axis, 0.02 over the standard's .206. The two agree once those are allowed for.
Gap between the receiver's rail and the handguard's, at the seam0.006 in ± 0.006 in 0.2 mmProvisionalPhoto: left side, NC22RB-UPPER-16-KIT_3_HR
Photo “between touching and one pixel (0.012 in)” used
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), 83.6 px/in at the seam. Read by the seam's dark line where it crosses the rail's side (rows 925–945 on a 16× gridded crop) is one pixel wide or less; the value is the middle of that, the ± its whole range
The two parts butt: the seam is a line, not a slot. Its width isn't resolved in the 2000 px photo.
Handguard rail's rear end (where its first slot's floor begins), X6.603 in ± 0.04 in 167.7 mmProvisionalWorked out: {.receiver_rail_front_x} + {.rail_gap}
Worked out 6.603 in ± 0.04 in used
{.receiver_rail_front_x} + {.rail_gap}, harvested
The handguard's rail starts at the seam with a slot, not a tooth (receiver_rail_front_x's note).
Handguard rail's first slot centre (slot 15 of the run), X6.705 in ± 0.035 in 170.3 mmConflictWorked out: {.rail_slot0_x} + 15 * {std.picatinny.slot_pitch}
Photo 6.621 in ± 0.035 in
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0. Read by slot 15's centre (counted from the rear) along the rail model, which puts every slot on one pitch within 0.0027 in; ± is 3× rail rms plus edge and anchor error
The handguard rail's first slot: the first whose centre is ahead of the seam.
Worked out 6.705 in ± 0.035 in used
{.rail_slot0_x} + 15 * {std.picatinny.slot_pitch}, harvested
Fifteen pitches ahead of the receiver's first slot.
The slots are drawn where the optics are indexed (slot 0 plus a whole number of pitches); the photo puts the handguard's first slot there within 0.002 in.
left and grid differ by 0.084 in beyond what each states it is good to.
The handguard's slots continue the receiver's pitch: the rail fit puts all 49 on one pitch within 0.0027 in, and the spacing across the seam is 33.01 px in the left photo against 32.77 to 33.19 for its four neighbours either side (19.87 against 19.59 to 19.95 in the right one). So the optics' one run of slots is what is drawn.
Handguard rail's top against the receiver rail's, at the seam (up positive)-0.008 in ± 0.006 in -0.2 mmCorroboratedPhoto: left side, NC22RB-UPPER-16-KIT_3_HR
Photo -0.0076 in ± 0.006 in used
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: rail model from 01-2b348f6a5149.calib.json (0.0010 in rms, drift -0.99%), anchored at takedown lug (1853.5,1074.5) = frame x 0. Read by tooth tops (the 50% level between the background and the tooth, over the middle of each tooth) fitted by a line over 7 teeth behind x 6.47 ({.handguard_rear_x}) and 7 ahead of it, the tooth at it left out, and compared there: -0.64 px at 83.6 px/in (scatter about the two lines 0.07 px); ± is half a pixel: the two parts' edges needn't read alike
The handguard's rail top against the receiver's at the seam: negative is lower.
Photo -0.007 in ± 0.01 in
right side, Nordic NC22-16-Upper-V2, harvested
Scale: rail model from 02-24d592636074.calib.json (0.0165 in rms, drift +0.30%), anchored at takedown lug (91.5,475.5) = frame x 0. Read by tooth tops (the 50% level between the background and the tooth, over the middle of each tooth) fitted by a line over 5 teeth behind x 6.47 ({.handguard_rear_x}) and 5 ahead of it, the tooth at it left out, and compared there: -0.35 px at 50.4 px/in (scatter about the two lines 0.07 px); ± is half a pixel: the two parts' edges needn't read alike
The larger photo (83.6 px/in against 50.4); the other side's photo reads the same step.
The handguard's rail sits a little below the receiver's: two photos, of the two sides, read the same step. Read from the teeth either side of the seam, each side fitted on its own, so the rail's tilt in the photo and the lens's bend are out of it. Along the handguard the rail's top then reads 0.02 to 0.06 in higher toward the muzzle in the same photos (and 2.17 in the flat-lay): a trend over 13 in, which a lens gives and a step doesn't, and which isn't drawn. M5's note that the handguard's rail reads higher was that trend.
Handguard rail's top surface above the pin centerline2.082 in ± 0.04 in 52.9 mmProvisionalWorked out: {.rail_top_above_pin} + {.handguard_rail_step}
Worked out 2.0824 in ± 0.04 in used
{.rail_top_above_pin} + {.handguard_rail_step}, harvested
The charging handle's T: its underside above the pin line, where it stands behind the receiver1.597 in ± 0.015 in 40.6 mmCorroboratedPhoto: the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05
Photo 1.56 in ± 0.05 in
right side, Nordic NC22-16-Upper-V2, 1200 px, harvested
Scale: the traced side profile's (profiles.side). Read by the outline's corner behind the rear face where the sloped rear end meets the T's underside: (-1.169, 1.56)
Photo 1.597 in ± 0.015 in used
the user's own 22RB: the receiver's rear from its left side, square on, the takedown lug's hole and ten of the rail's slots in frame; 2026-10-05, from the site owner
Scale: the rail's own pitch in the same view (ten slots' rear walls 185.9 px apart, 184.5 to 187.5: 472 px/in) and the T's rear face, which reads 1.595 in behind slot 0's rear wall where the ledger has 1.552: the T's end is 0.57 in nearer the lens than the rail's near edge and 1.6% larger, a lens 35 in or more away; 480 px/in at the T's end. The lug's hole reads 0.252 at its own depth. Read by the T's left end against the floor: its top 20.7 px under the rail's top line (rows 536.2 less 0.0056 a column, by seven tooth tops), its underside 237 px under it at columns 2440 to 2460 (row 758 to 760); ± is 5 px at the two edges and the scale's 1%
The user's own upper, square on from 35 in or more, scaled in the T's own plane; the product photo's corner, 0.037 in lower, is within its own ±.
Behind the receiver's rear face the traced outline is the receiver's sloped rear end up to here and the handle's T above it, as an AR's handle sits about 0.86 in above the bore (Aero's receiver's latch notch). The 22RB's handle is Nordic's own; a buyer's review on Nordic's page says it is "compatible with aftermarket latches": an AR-pattern T (std.ar15.charging_handle_t_width).
Bolt, as it shows through the ejection port: the lower edge of its flat face, Y0.985 in ± 0.03 in 25 mmProvisionalPhoto: the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03
Photo 0.985 in ± 0.03 in used
the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03, from the site owner
Scale: the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own. Read by the line where the flat ends and the bright band under it begins, at photo x 1300, 1360 and 1420: rows 1125, 1128, 1131 (1.007 at the side face's scale). Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (0.022 here). ± is the rest of that (0.01), the picks (0.01) and the pocket's own ± as a scale (0.01)
What the user's close photo shows of the bolt through the port (the model review, 2026-10-05: it was drawn as the bore's round bar, polished): a flat, matte, bead-blasted face from this line up to bolt_flat_top_y, between bolt_rear_x and bolt_front_x, with a hollow pin in it (bolt_pin_*); under the line a bright band 0.12 in tall that ends 0.866 above the pin line, which is the bore's axis (0.8775) within the reading: the round body's own crest, seen from a little above. The model keeps the round body where it was and stands the flat on it at this line; how far the flat really is behind the round's crest, and behind the opening, isn't read.
Bolt, as it shows through the ejection port: the upper edge of its flat face, Y1.285 in ± 0.03 in 32.6 mmProvisionalPhoto: the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03
Photo 1.285 in ± 0.03 in used
the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03, from the site owner
Scale: the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own. Read by the flat's upper edge under the opening's own, at photo x 1330 and 1420: rows 1070 and 1074.5 (1.299 at the side face's scale). Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (0.014 here). ± as bolt_flat_bottom_y's
0.024 under the opening's upper edge on file (ejection_port_top_y, from Nordic's photos): the photo has a dark line between the two.
Bolt, as it shows through the ejection port (closed): its rear end, X3.6 in ± 0.015 in 91.4 mmConflictPhoto: the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05
Photo 3.68 in ± 0.03 in
the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03, from the site owner
Scale: the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own. Read by where the flat begins along rows 1100 and 1115: photo x 1252 and 1249 (3.681 at the side face's scale). Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (under 0.005 here: it is nearly under the lens). ± as bolt_flat_bottom_y's
Its upper rear corner is rounded (about 0.08 in by this photo; 0.14 by the square one: bolt_rear_corner_r, drawn since 2026-10-12).
Photo 3.6 in ± 0.015 in used
the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05, from the site owner
Scale: the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102). Read by the face's rear edge at mid height, where it is upright: light begins at column 478 along row 930 and at 471 along row 1000 (475: 3.600). ± is 7 px and the frame's
Square on and four times the other photo's scale. The other read where the flat begins along two rows near its top, through the round of its rear upper corner (bolt_rear_corner_r), which is 0.14 in: 0.08 further forward, as that round is there.
The rear end where it is upright, read square on at 789 px/in; the first reading was taken through the corner's round, which its own note says wasn't drawn. Drawn since 2026-10-12, so the end is the end.
user and close differ by 0.08 in beyond what each states it is good to.
Bolt, as it shows through the ejection port (closed): its front end, X5.18 in ± 0.03 in 131.6 mmProvisionalPhoto: the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03
Photo 5.18 in ± 0.03 in used
the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03, from the site owner
Scale: the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own. Read by where the flat ends along rows 1100 and 1115: photo x 1534 and 1535 (5.147 at the side face's scale). Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (0.035 here, the furthest from the lens: ± 0.013 of it for the depth). ± with the picks (0.01) and the scale (0.01)
Its upper front corner is cut off (about 0.07 by 0.08 in by this photo; a round of 0.05 by the square one: bolt_front_corner_r, drawn since 2026-10-12). Ahead of it the opening is dark for 0.10 in.
Bolt: the hollow pin in its flat face, centre, X5 in ± 0.03 in 127 mmProvisionalPhoto: the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03
Photo 5 in ± 0.03 in used
the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03, from the site owner
Scale: the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own. Read by the pin's end, a bright ring round a dark socket: the ring's outer edge from photo x 1483 to 1518 on row 1096 and from row 1077 to 1116 on column 1499, centred (1500.5, 1096.5): 4.969 at the side face's scale. Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (0.03 here). ± as bolt_front_x's
Bolt: the hollow pin in its flat face, centre, Y1.187 in ± 0.03 in 30.1 mmProvisionalPhoto: the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03
Photo 1.187 in ± 0.03 in used
the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03, from the site owner
Scale: the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own. Read by the same ring's centre (1500.5, 1096.5): 1.204 at the side face's scale. Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (0.017 here). ± as bolt_flat_bottom_y's
Bolt: the hollow pin's diameter (its end, rim to rim)0.196 in ± 0.015 in 5 mmProvisionalPhoto: the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03
Photo 0.196 in ± 0.015 in used
the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03, from the site owner
Scale: the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own. Read by the ring's outer edge: 35 px along the rifle and 39 across it, 37 px at 193.5 px/in and 2.7% more for the face's depth. ± is the two readings' spread (2 px) and the depth's
Not drawn: the model has the pin's socket alone (bolt_pin_socket_d).
Bolt: the socket in its flat face (a screw's, down a countersunk seat: bolt_pin_seat_d), diameter0.101 in ± 0.015 in 2.6 mmProvisionalPhoto: the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03
Photo 0.101 in ± 0.015 in used
the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03, from the site owner
Scale: the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own. Read by the dark middle of the ring: 19 px along the rifle (row 1096: 1491 to 1510) and 18 to 19 across it (column 1499: 1088 to 1106), at 193.5 px/in and 2.7% more for the face's depth. ± is 2 px and the depth's
Bolt: the seat round the socket in its flat face, diameter at the face0.205 in ± 0.012 in 5.2 mmProvisionalPhoto: the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05
Photo 0.205 in ± 0.012 in used
the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05, from the site owner
Scale: the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (ejection_port_rear_x to ejection_port_front_x: 789 px/in). The pocket's rim, 0.23 in nearer the lens, reads 820: a lens about 6 in away, so nothing is read across planes. Read by the ring's outer edge along the rifle (row 865: 1497 to 1662, 165 px) and across it (column 1580: 796 to 955, 159 px): 0.209 and 0.202. The dark socket inside it is 86 px along and 68 across, 0.087 to 0.109: bolt_pin_socket_d's 0.101 again. ± is 4 px at each edge and the two directions' difference
The socket in the flat (bolt_pin_socket_d) has a bright ring round it that reaches the flat's upper edge: a seat sunk into the face, twice the socket across. The close photo of 2026-10-05 shows what the "hollow pin" is: a screw's socket down a countersunk hole. How deep the seat is isn't read: drawn with a flat floor half the edge's break deep (bolt_top_break), the ring being one tone from its rim to the socket; it had been a cone.
Bolt: the round of its flat faces rear upper corner0.143 in ± 0.015 in 3.6 mmProvisionalPhoto: the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05
Photo 0.143 in ± 0.015 in used
the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05, from the site owner
Scale: the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102). Read by the outline about the corner: the top edge at row 791, the rear edge at column 475, and between them on a circle of 113 px that touches both (at column 520 the outline is at row 815 for the circles 814; at column 500, 835 for 833). ± is 12 px
The faces rear upper corner is a round, not a corner cut off: the outline leaves the top edge about 0.15 in ahead of the rear end and meets the rear edge as far down. The edges break (bolt_top_break) follows it round.
Bolt: the round of its flat faces front upper corner0.05 in ± 0.012 in 1.3 mmProvisionalPhoto: the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05
Photo 0.05 in ± 0.012 in used
the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05, from the site owner
Scale: the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102). Read by the top edge is straight to about column 1690 and the front edge from about row 835, the front end at column 1727: a round of 37 to 44 px. ± is 9 px
Smaller than the rear one. The other close photo read it as a corner cut off, about 0.07 by 0.08 in (bolt_front_xs note).
Bolt: the break along its flat faces upper edge, its height as it shows from the side0.054 in ± 0.008 in 1.4 mmProvisionalPhoto: the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05
Photo 0.054 in ± 0.008 in used
the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05, from the site owner
Scale: the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102). Read by down columns 700, 850, 1000 and 1250: the bolts top edge at rows 790 to 791 and the bands lower edge at 832 to 835: 43 px. ± is 6 px
A band of another tone along the faces top, between the face and the bolts top edge, which runs on round the rear upper corner and down the front end. How deep it goes isnt read: drawn at 45 degrees. Below the face the bolt has a taller band of the same kind, from bolt_flat_bottom_y down to the ports lower lip (0.12 in), which is drawn as the round it had been taken for.
Bolt: the half-round cut in its lower edge over the extractor, its middle, X4.798 in ± 0.012 in 121.9 mmProvisionalPhoto: the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05
Photo 4.798 in ± 0.012 in used
the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05, from the site owner
Scale: the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102). Read by along row 1060, 31 px above the slots upper edge, the arch is dark from column 1367 to 1473: its middle at 1420. ± is 6 px and the frames
An arch cut up into the bolts lower band from the slot the extractor lies in, over the extractors raised rear end. extractor_rear_xs note had it at about 4.8 and 0.075 in radius from the other photo.
Bolt: the half-round cut over the extractor, its top, Y0.976 in ± 0.008 in 24.8 mmProvisionalPhoto: the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05
Photo 0.976 in ± 0.008 in used
the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05, from the site owner
Scale: the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102). Read by the archs top at row 1042 on columns 1400 to 1440 (the slots upper edge is at rows 1091 to 1093, 0.913 by the same frame, for extractor_top_ys 0.924). ± is 5 px
Just under the line where the face ends (bolt_flat_bottom_y): the arch stays inside the lower band.
Bolt: the half-round cut over the extractor, its radius0.07 in ± 0.008 in 1.8 mmProvisionalPhoto: the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05
Photo 0.07 in ± 0.008 in used
the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05, from the site owner
Scale: the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102). Read by half its width where it opens into the slot (columns 1352 to 1470 at row 1088: 59 px, 0.075) and its height above the slots upper edge (rows 1042 to 1092: 50 px, 0.063); a round of 0.07 between the two. ± covers both
Drawn as a round of this radius whose top is at extractor_notch_top_y.
Extractor: its raised rear end under the half-round cut, rear, X4.748 in ± 0.01 in 120.6 mmProvisionalPhoto: the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05
Photo 4.748 in ± 0.01 in used
the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05, from the site owner
Scale: the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102). Read by along row 1105 the hump is light from column 1381 to 1476; its top is at rows 1087 to 1090, the slots upper edge. ± is 6 px
The extractors rear end stands up into the cut over it, its top lit: a rounded hump as wide as the cut, with the bar running forward from it to extractor_front_x. Ahead of the bar the slot is empty to the bolts front end.
Extractor: its raised rear end under the half-round cut, front, X4.869 in ± 0.01 in 123.7 mmProvisionalPhoto: the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05
Photo 4.869 in ± 0.01 in used
the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05, from the site owner
Scale: the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102). Read by as extractor_pivot_rear_x: column 1476. The bars front end is at column 1517 along row 1125 (4.921, for extractor_front_xs 4.936)
As extractor_pivot_rear_x.
Extractors spring: its front end, X4.554 in ± 0.012 in 115.7 mmProvisionalPhoto: the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05
Photo 4.554 in ± 0.012 in used
the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05, from the site owner
Scale: the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102). Read by the coils glints along rows 1110 to 1134 run from column 1100 to 1228; ahead of that one even bar. ± is 8 px
A coil spring lies in the slot behind the extractor, from the slots rear end (extractor_rear_x) forward, and a thin rod runs from it to the extractors raised end.
Extractors spring: its outside diameter0.04 in ± 0.01 in 1 mmProvisionalPhoto: the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05
Photo 0.04 in ± 0.01 in used
the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05, from the site owner
Scale: the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102). Read by down columns 1120 and 1160 the coils are lit from row 1108 to 1138: 30 px. ± is 8 px
The wires size isnt read: drawn at a third of the pitch.
Extractors spring: from one coil to the next0.037 in ± 0.005 in 0.9 mmProvisionalPhoto: the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05
Photo 0.037 in ± 0.005 in used
the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05, from the site owner
Scale: the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102). Read by along rows 1122 to 1134 the coils glints are at columns 1130, 1160, 1190, 1216 and 1226: 29 px from one to the next. ± is 4 px
Counted on its glints: four and a half coils in its length.
Extractors spring: the rod from it to the extractor, diameter0.019 in ± 0.006 in 0.5 mmProvisionalPhoto: the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05
Photo 0.019 in ± 0.006 in used
the user's own 22RB, the ejection port from the right, square on and close; 2026-10-05, from the site owner
Scale: the port's own opening in the same photo, in the flat's plane within 0.02 in: its two ends 1356 px apart along the rifle for the ledger's 1.718 in (789 px/in; bolt_pin_seat_d's), and places counted from the screw's middle in the same photo (photo 1579.5, 875.5: bolt_pin_x, bolt_pin_y), which puts the ledger's other figures of the bolt on their edges here within 0.012 in (its front end at photo 1727 for 1722, the dark bar's rear at 1093 for 1102). Read by down columns 1280 and 1340 one lighter band about row 1128, 15 px tall. ± is 5 px
An even bar a little under the slots middle.
Extractor (the dark bar along the bolt's side at the bore's height): its rear end, X4.395 in ± 0.03 in 111.6 mmProvisionalPhoto: the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03
Photo 4.395 in ± 0.03 in used
the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03, from the site owner
Scale: the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own. Read by the dark bar let into the round body under the flat: dark from photo x 1384 on rows 1144 to 1150 (4.381 at the side face's scale). Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (0.015 here). ± as bolt_flat_bottom_y's
A bar of darker steel lying along the bolt's right side, centred on the bore's axis within the reading (0.882 against 0.8775); its rear half is ribbed like a spring's coils and a half-round is cut in the bolt above its front half (about 0.075 in radius, centred 4.8 ahead of the pin): both drawn since 2026-10-12 from the square photo (extractor_spring_*, extractor_notch_*), where the bar is a slot with a spring, a rod and the extractor in it, empty ahead of the extractor to the bolt's front end. The review calls it the extractor; no document on file names it.
Extractor: its front end, X4.936 in ± 0.03 in 125.4 mmProvisionalPhoto: the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03
Photo 4.936 in ± 0.03 in used
the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03, from the site owner
Scale: the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own. Read by dark to photo x 1486 on rows 1147 to 1153 (4.907 at the side face's scale). Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (0.029 here). ± as bolt_front_x's
Extractor: its upper edge, Y0.924 in ± 0.03 in 23.5 mmProvisionalPhoto: the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03
Photo 0.924 in ± 0.03 in used
the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03, from the site owner
Scale: the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own. Read by its upper edge at photo x 1390 to 1445: row 1143 (0.948 at the side face's scale). Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (0.024 here). ± as bolt_flat_bottom_y's
Extractor: its lower edge, Y0.84 in ± 0.03 in 21.3 mmProvisionalPhoto: the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03
Photo 0.84 in ± 0.03 in used
the user's own 22RB, the receiver's right side from close, the ejection port near the frame's middle; 2026-10-03, from the site owner
Scale: the port's own pocket in the same photo: its two ends 347.7 px apart along the rifle for the ledger's 1.797 in (ejection_port_pocket_rear_x to ejection_port_pocket_front_x: 193.5 px/in on the receiver's side face) and its lower edge for the height (ejection_port_pocket_bottom_y); the photo lies 2.7 degrees off level, by the pocket's edges and the bolt's own. Read by its lower edge against the dark under it, on a four times enlargement: row 1159 ± 3 (0.866 at the side face's scale). Read at the side face's scale and carried to the bolt's face, which stands further from the lens by an amount no photo on file gives: between the pocket's floor (0.23 in in) and 0.45 in. The lens was 12.7 in off the side face (the lug holes read 184 px/in, 0.655 in behind it) and over a point 0.6 in behind the port's middle and 0.7 above it (the frame's middle), so what is on the bolt reads 2 to 4% near that point: the figure has 0.34 in of depth allowed for (0.026 here). ± is that pick (0.016) and the rest as bolt_flat_bottom_y's
0.007 above the opening's lower edge on file (ejection_port_bottom_y).
Handguard clamp block: its flat underside, Y-0.114 in ± 0.012 in -2.9 mmProvisionalPhoto: the user's own 22RB lying on its left side on tile, its right side square on from 5 to 7 ft; 2026-10-03
Photo -0.114 in ± 0.012 in used
the user's own 22RB lying on its left side on tile, its right side square on from 5 to 7 ft; 2026-10-03, from the site owner
Scale: the frame the side outline is traced in (profiles.side): the two lug holes' see-through centres and the rail's first and last slots, 106.9 px/in, 1.2 px rms over the four; the block is astride the centre plane the frame lies in. Read by the silhouette's lower edge (the first sample darker than 70 up a column, 0.002 in steps) at fourteen columns from x 7.10 to 7.95: -0.104 to -0.118, mean -0.113; the four columns over the tile's grout line (7.55 to 7.75, -0.120 to -0.132) left out. Nordic's left view (2b348f6a5149), taken from about 20 degrees above, has the block's near lower edge 21 px under the handguard's (0.25 in at the rail's 83.8 px/in), which is this drop seen past a block 1.06 wide
The block under the rear end of the handguard that its two clamp screws cross. It hangs 0.19 in under the handguard (handguard_bottom_y; the same photo has that edge at 0.070).
Handguard clamp block: where its flat underside begins, X7.05 in ± 0.04 in 179.1 mmProvisionalPhoto: the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03); 0dfba70ae389 (the same upper from below, close; 2026-10-05
Photo 7.05 in ± 0.04 in used
the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03); 0dfba70ae389 (the same upper from below, close; 2026-10-05, from the site owner
Scale: from the side, the pin frame of profiles.side (106.9 px/in); from below, the bottom face's own M-LOK slots: their rear ends 269 px apart for the standard's 40 mm (170.7 px/in), the short slot's rear end at column 1797 for 9.227 (mlok_slot_front_x, mlok_rear_slot_length). Read by from the side the lower edge leaves the flat between x 7.10 (-0.105) and 7.05 (-0.100, then -0.070 at 7.00): 7.07. From below the flat is the lighter face, its rear edge at columns 1422 to 1424 on the rows either side of the slit (960, 1030): 7.03 by the slots, 7.045 with the seam of the same photo (column 1346) put on handguard_rear_x. The block's near face is 0.5 in nearer the lens than the frame's plane in the side view: 0.02 in along the rifle if the lens stood over the middle of the upper, inside the ±
Handguard clamp block: where its flat underside ends, X7.955 in ± 0.035 in 202.1 mmProvisionalPhoto: the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03); 0dfba70ae389 (the same upper from below, close; 2026-10-05
Photo 7.955 in ± 0.035 in used
the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03); 0dfba70ae389 (the same upper from below, close; 2026-10-05, from the site owner
Scale: as handguard_clamp_flat_rear_x: the pin frame from the side, the bottom face's M-LOK slots from below. Read by from the side the lower edge is on the flat at x 7.95 (-0.115) and off it at 8.00 (-0.080): 7.96. From below the lighter face ends at column 1580 on rows 930, 960 and 1030: 7.944 by the slots (the block 0.19 in nearer a lens about 29 in away, by the handguard's own width in the frame: 2 px), 7.956 with the seam on handguard_rear_x
Handguard clamp block: where its rear ramp meets the handguard's underside on the centre line, X6.81 in ± 0.06 in 173 mmProvisionalPhoto: the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03
Photo 6.81 in ± 0.06 in used
the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03, from the site owner
Scale: the pin frame of profiles.side (106.9 px/in). Read by the silhouette's lower edge at x 7.05, 7.00, 6.95, 6.90: -0.100, -0.070, -0.040, 0.005: a straight rise of 0.70 in per in, which is at the underside's own level in this photo (0.070) at 6.81. Nordic's left view (2b348f6a5149; the seam at column 1303, the rail's pitch 33.0 px: 83.8 px/in) has the outline back on the underside's line at column 1290: 6.75
The ramp from the flat up toward the seam. Behind x 6.90 the edge eases in to the underside (0.025 at 6.85, 0.064 at 6.70): a blend, or the shadow under a part lying on tile, and drawn as neither: the ramp is one plane.
Handguard clamp block: where its front ramp meets the handguard's underside on the centre line, X8.33 in ± 0.04 in 211.6 mmProvisionalPhoto: the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03
Photo 8.33 in ± 0.04 in used
the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03, from the site owner
Scale: the pin frame of profiles.side (106.9 px/in). Read by the silhouette's lower edge from x 8.00 to 8.35 in steps of 0.05: -0.080, -0.050, -0.015, 0.015, 0.040, 0.050, 0.065, 0.070, and 0.070 to 0.075 from there on: on the underside at 8.33. Nordic's left view (2b348f6a5149, 83.8 px/in from the seam at column 1303) has the outline leave the underside's line at column 1157: 8.34
Handguard clamp block: its width across the rifle1.06 in ± 0.04 in 26.9 mmProvisionalPhoto: the user's own 22RB from below, close; 2026-10-05); bdb43e3235ed (the same from below, the whole upper; 2026-10-03
Photo 1.06 in ± 0.04 in used
the user's own 22RB from below, close; 2026-10-05); bdb43e3235ed (the same from below, the whole upper; 2026-10-03, from the site owner
Scale: the bottom face's own M-LOK slots in 0dfba70ae389: their rear ends 269 px apart for the standard's 40 mm (170.7 px/in); the block's face stands 0.19 in nearer a lens about 29 in away (the handguard's 1.602 in reads 266 px at its widest, 0.8 in further), which is 0.7%. Read by the lighter flat's edge up columns 1500, 1530 and 1560: row 899 (and 895 to 907 at 1560), 92.5 px from the slit's middle (rows 985 to 995): 0.538 in a side, 1.077 across; its other edge isn't a step against the diagonal beside it and is taken as the same. bdb43e3235ed has the flat 113 px across where the handguard is 172 (1.602 in): 1.05
Wider than the handguard's bottom flat (0.66): its two side faces stand out of the lower diagonal faces, and meet them where the diagonals are this far apart (handguard_clamp_side_top_y is that line, read in another photo).
Handguard clamp block: the upper edge of its side face, Y0.283 in ± 0.015 in 7.2 mmProvisionalPhoto: the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03
Photo 0.283 in ± 0.015 in used
the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03, from the site owner
Scale: the pin frame of profiles.side (106.9 px/in). Read by the block's side face is lit (level 35 to 50) between the dark lower diagonal above it and the tile: its upper edge up thirteen columns from x 6.90 to 8.20, 0.275 to 0.295
Where the block's side face meets the handguard's lower diagonal face. Not built from: the script draws the side faces at handguard_clamp_width and checks that they meet the diagonals at this height.
Handguard clamp block: its side face's upper rear corner, X6.85 in ± 0.04 in 174 mmProvisionalPhoto: the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03
Photo 6.85 in ± 0.04 in used
the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03, from the site owner
Scale: the pin frame of profiles.side (106.9 px/in). Read by the lit side face's rear edge: its lower end at 0.270, 0.240, 0.195, 0.155, 0.120, 0.050 up columns 6.85 to 7.10: a line from the face's upper edge at 6.85 down to the flat at 7.29 (0.88 in per in)
Handguard clamp block: its side face's upper front corner, X8.23 in ± 0.04 in 209 mmProvisionalPhoto: the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03
Photo 8.23 in ± 0.04 in used
the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03, from the site owner
Scale: the pin frame of profiles.side (106.9 px/in). Read by the lit side face's front edge: its lower end at 0.105, 0.150, 0.180, 0.220 up columns 8.05 to 8.20, and no lit face at 8.25: a line from the face's upper edge at 8.23 down to the flat at 7.77 (0.77 in per in)
Handguard clamp block: how far its flat's two rear corners are cut back0.24 in ± 0.05 in 6.1 mmProvisionalPhoto: the user's own 22RB, right side; 2026-10-03); 0dfba70ae389 (the same from below, close; 2026-10-05
Photo 0.24 in ± 0.05 in used
the user's own 22RB, right side; 2026-10-03); 0dfba70ae389 (the same from below, close; 2026-10-05, from the site owner
Scale: the pin frame from the side (106.9 px/in); the bottom face's M-LOK slots from below (170.7 px/in). Read by from the side, the side face's rear edge comes down to the flat at 7.29, 0.24 ahead of handguard_clamp_flat_rear_x. From below, the flat's rear edge is 8 px further forward on row 930 (0.17 in inside the side) and 22 px on row 1060 (0.13 inside) than on the middle rows: 0.22 and 0.26 for a cut at 45 degrees
From below the flat's corners are cut off; from the side the cut is the edge the side face ends on. Drawn as a facet from the flat's cut corner up to the side face's upper corner.
Handguard clamp block: how far its flat's two front corners are cut back0.17 in ± 0.05 in 4.3 mmProvisionalPhoto: the user's own 22RB, right side; 2026-10-03); 0dfba70ae389 (the same from below, close; 2026-10-05
Photo 0.17 in ± 0.05 in used
the user's own 22RB, right side; 2026-10-03); 0dfba70ae389 (the same from below, close; 2026-10-05, from the site owner
Scale: the pin frame from the side (106.9 px/in); the bottom face's M-LOK slots from below (170.7 px/in). Read by from the side, the side face's front edge comes down to the flat at 7.77, 0.185 behind handguard_clamp_flat_front_x. From below, the flat's front edge is 7 px short on row 1060 (0.13 in inside the side) and whole on row 930 (0.17 inside): 0.17, and under 0.17
Handguard clamp: the slit along the underside, across0.059 in ± 0.012 in 1.5 mmProvisionalPhoto: the user's own 22RB from below, close; 2026-10-05
Photo 0.059 in ± 0.012 in used
the user's own 22RB from below, close; 2026-10-05, from the site owner
Scale: the bottom face's own M-LOK slots: 170.7 px/in. Read by its two edges up columns 1470 to 1560: rows 984 to 985 and 994 to 995, 10 px; at half its depth of tone 9 to 11 rows at columns 1450, 1500, 1550, 1620
The handguard is slit along the middle of its underside, from the seam through the block, so that the two screws can close it. Black in every photo: what is behind it isn't seen.
Handguard clamp: where the slit ends, X8.4 in ± 0.04 in 213.4 mmProvisionalPhoto: the user's own 22RB from below, close; 2026-10-05
Photo 8.4 in ± 0.04 in used
the user's own 22RB from below, close; 2026-10-05, from the site owner
Scale: the bottom face's own M-LOK slots: 170.7 px/in, the short slot's rear end at column 1797 for 9.227. Read by the slit's own rows (983 to 991) are dark (7 to 28) to column 1650 and the face's tone (49) from 1660: it ends at 1655, 8.395. Behind the block (rows 994 to 1002, columns 1330 to 1430) it is dark to the seam at 1346
Handguard clamp: its cross screws2ProvisionalPhoto: the user's own 22RB, right side: two socket heads in counterbores); 584c3ded24e1 (its left side: two tapped holes
Photo 2 count used
the user's own 22RB, right side: two socket heads in counterbores); 584c3ded24e1 (its left side: two tapped holes, from the site owner
Scale: none: a count. Read by counted: two heads on the block's right face, two threaded holes on its left, in the user's photos and in Nordic's (24d592636074, 2b348f6a5149)
Handguard clamp: the rear screw's axis, X7.3 in ± 0.04 in 185.4 mmProvisionalPhoto: the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03
Photo 7.3 in ± 0.04 in used
the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03, from the site owner
Scale: the pin frame of profiles.side (106.9 px/in). Read by the dark ring round the head (its counterbore's shadow) fitted as a circle on a 0.005 in grid of centres and radii: centre 7.295, 0.105. The head is 0.5 in nearer the lens than the frame's plane: up to 0.02 in further forward if the lens stood over the middle of the upper, inside the ±. Nordic's left view (2b348f6a5149, 83.8 px/in from the seam at column 1303) has the tapped hole at column 1244: 7.30
Handguard clamp: from one screw's axis to the other's0.505 in ± 0.015 in 12.8 mmProvisionalPhoto: the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03
Photo 0.505 in ± 0.015 in used
the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03, from the site owner
Scale: the pin frame of profiles.side (106.9 px/in). Read by the two rings' fitted centres: 7.295 and 7.800. Nordic's left view (2b348f6a5149) has the two holes 41 px apart at 83.8 px/in: 0.49
Handguard clamp: the screws' axes, Y0.1 in ± 0.02 in 2.5 mmProvisionalPhoto: the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03
Photo 0.1 in ± 0.02 in used
the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03, from the site owner
Scale: the pin frame of profiles.side (106.9 px/in). Read by the two rings' fitted centres: 0.105 and 0.100
Handguard clamp: the counterbore each screw head sits in, its diameter0.27 in ± 0.02 in 6.9 mmProvisionalPhoto: the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03
Photo 0.27 in ± 0.02 in used
the user's own 22RB, right side, square on from 5 to 7 ft; 2026-10-03, from the site owner
Scale: the pin frame of profiles.side (106.9 px/in). Read by the dark ring round each head, fitted: radius 0.135 on both; along the rifle through the rear one, its lit wall at -0.11 and its shadowed wall at +0.145 of the centre
How deep it is, and how far under the face the head stands, no view gives.
Handguard clamp: a screw's head, its diameter0.2 in ± 0.03 in 5.1 mmProvisionalPhoto: the user's own 22RB, the receiver's right side from close; 2026-10-03
Photo 0.2 in ± 0.03 in used
the user's own 22RB, the receiver's right side from close; 2026-10-03, from the site owner
Scale: the counterbore's own ring in the same photo and the same face: 50 px across for handguard_clamp_counterbore_d. Read by the head inside the ring, 36 to 40 px across on both screws (centres 1908, 1327 and 2005, 1333). Within one face of a close photo: a ratio, nothing across planes
Handguard clamp: a screw's hex socket, across0.11 in ± 0.02 in 2.8 mmProvisionalPhoto: the user's own 22RB, the receiver's right side from close; 2026-10-03
Photo 0.11 in ± 0.02 in used
the user's own 22RB, the receiver's right side from close; 2026-10-03, from the site owner
Scale: the counterbore's own ring in the same photo and the same face: 50 px across for handguard_clamp_counterbore_d. Read by the socket in each head, 20 to 22 px across
A socket head: the hex is lit inside both heads. How deep it goes isn't seen.
Handguard clamp: the threaded holes on the block's left face, their diameter0.135 in ± 0.02 in 3.4 mmProvisionalPhoto: the user's own 22RB, close on the seam from the left, the upper upside down in the frame; 2026-10-04
Photo 0.135 in ± 0.02 in used
the user's own 22RB, close on the seam from the left, the upper upside down in the frame; 2026-10-04, from the site owner
Scale: the two holes' own spacing in the same photo and the same face: their rear edges 275 px apart along the rifle for handguard_clamp_screw_spacing (545 px/in). Read by each hole along the rifle on rows 690 and 700: 71 px (columns 1510 to 1581) and 74 (1785 to 1859). Along the rifle only: the face is seen from well above its square
The screws go in from the right and thread into the block's left half: on the left there are two open threaded holes, their threads lit. Taken as on the screws' own axes.
Handguard: the blind panel behind each row of M-LOK slots, its length0.93 in ± 0.04 in 23.6 mmProvisionalPhoto: left side, NC22RB-UPPER-16-KIT_3_HR
Photo 0.93 in ± 0.04 in used
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: the short slot beside it in the same face: 80 px (columns 1003 to 1083) for mlok_rear_slot_length. Read by the panel's two ends on the side face and on the upper diagonal: columns 1109 and 1189, 80 px, the short slot's own length. (The rail's pitch in the same photo is 33.0 px, 83.8 px/in, which has both 0.955.)
Behind the rearmost (short) slot of the rows on the two side faces and the two upper diagonal faces there is a panel of the short slot's own outline that doesn't go through: Nordic's two side views and the user's close one (e421a9af0aa7) have it on those four faces. The three lower faces have the clamp's block there and no room for one (the user's views from below). A side view says where it is and not which way it goes: taken as milled in, as the slots and the grooves are, and its depth isn't read.
Handguard: the blind panel behind each row, across the face0.29 in ± 0.02 in 7.4 mmProvisionalPhoto: left side, NC22RB-UPPER-16-KIT_3_HR
Photo 0.29 in ± 0.02 in used
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: the slot beside it in the same face: its opening 22 px across (rows 967 to 989 at column 1030) for the standard's 7 mm (std.mlok.slot_width). Read by the panel's two edges up columns 1130, 1150 and 1170 on the upper diagonal: rows 968 and 991, 23 px. The user's close view of the right side (e421a9af0aa7) has it 57 to 63 px across where the two grooves either side of the row are 87 px apart for twice handguard_groove_offset: 0.275 to 0.30
Handguard: from the blind panel's front end to the rear end of the short slot ahead of it0.31 in ± 0.03 in 7.9 mmProvisionalPhoto: left side, NC22RB-UPPER-16-KIT_3_HR
Photo 0.31 in ± 0.03 in used
left side, NC22RB-UPPER-16-KIT_3_HR, harvested
Scale: the short slot beside it in the same face (80 px for mlok_rear_slot_length: 86 px/in) and the rail's pitch in the same photo (33.0 px: 83.8 px/in). Read by from the panel's front end (column 1109) to the short slot's rear end (1083): 26 px, 0.30 and 0.31 by the two scales. Nordic's right view (24d592636074) has 16 px of gap beside a panel 50 px long: 0.30. The user's close view (e421a9af0aa7) has 30 px beside a panel 188 long, which would be 0.15: its slot is at the frame's edge, 5 in off the lens's axis from 10 in, and that reading is set aside
The web the standard leaves between two slots of a row is 0.315 (std.mlok.slot_pitch less std.mlok.slot_length): the panel stands off the short slot as a slot would.
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
AR-15 receiver pins
- Lower receivers
- Aero Precision M4E1 complete lower, A2 grip and M4 stock, Aero Precision M4E1 Stripped Lower Receiver, Battle Arms Development Workhorse stripped lower, BCM MK2 AR-15 Lower Receiver, Bear Creek Arsenal BC-15 Multi Caliber, Lower Receiver, Black Anodized, Geissele Automatics Super Duty AR-15 Lower Receiver - Stripped Lower, Palmetto State Armory AR-15 "Stealth" Stripped Lower Receiver
Picatinny rail (MIL-STD-1913)
- Red dot mounts
- Aimpoint Duty RDS One-piece TNP Mount, 30 mm, Aimpoint LRP (Lever Release Picatinny) Mount with 39 mm Spacer, for Micro, Aimpoint One-piece Torsion Nut Mount and Spacer, 39 mm, Geissele Super Precision T1 Mount - 1.93" Height, Geissele Super Precision T1 Mount - Absolute Co-Witness, Geissele Super Precision T1 Mount - Lower 1/3 Co-Witness, Holosun 1.63 in lower 1/3 co-witness pedestal mount (HS-MOUNT-AR-RISER-ARO), Midwest Industries MK2 QD T2 Aimpoint Mount, Low, Midwest Industries MK2 QD T2 Aimpoint Mount, Lower 1/3 Cowitness, Midwest Industries MK2 QD T2 Aimpoint Mount, NV 2.26 in Height, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – 1.93″ HEIGHT, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – LOWER 1/3 (39MM HEIGHT), Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.42 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.57 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.93 in, Scalarworks LEAP/02 Aimpoint Micro T-2 quick-detach mount, 2.26 in, SIG Sauer M1913 I-BEAM Mount, 1.41 in absolute co-witness, SIG Sauer See-Through Riser Mount, 1.41 in absolute co-witness, Unity Tactical FAST Micro Mount, 2.26 in optical centerline
- Optics
- Aimpoint Patrol Rifle Optic (PRO) Red Dot Reflex Sight - QRP2 Mount, EOTECH HWS EXPS3 holographic weapon sight, 1-Dot Speed Ring, Holosun HS510C Open Reflex MRS Solar QD Mount
- Lights
- Olight Baldr S BL, Streamlight ProTac Rail Mount HL-X, SureFire Mini Scout Light Pro, SureFire Scout Light Pro Dual Fuel
- Backup sights
- Daniel Defense A1.5 Fixed Rear Sight, Daniel Defense Rail Mounted Fixed Front Sight, Magpul MBUS 3 Sight – Front, Magpul MBUS 3 Sight – Rear, Magpul MBUS Pro Sight – Front, Magpul MBUS Pro Sight – Rear
- Magnifiers
- EOTECH G33 Magnifier, STS Mount, EOTECH G45 Magnifier, STS Mount, Holosun HM3X 3× magnifier with flip mount
- Scope mounts
- Primary Arms Deluxe AR-15 Scope Mount - 30mm, Primary Arms SLx Cantilever 30mm Mount - 1.5", Reptilia AUS™ MOUNT - 30MM DIAMETER - 39MM HEIGHT, Scalarworks LEAP/08 quick-detach scope mount, 30 mm, 1.57 in, SIG SAUER ALPHA-MSR scope mount, 30 mm, Vortex Sport Cantilever 30mm Mount
Muzzle thread
- Muzzle devices
- Dead Air XRF Xeno Rimfire Muzzle Brake, HUXWRX Flash Hider-QD 556 1/2x28, Mil-spec A2 flash hider, 1/2-28 (drawing 9349051), Nordic Components 1/2-28 thread protector (ships on the 22RB), Otter Creek Labs Polonium, Otter Creek Labs Polonium K, Precision Armament M4-72 Severe-Duty® Compensator, SilencerCo Sparrow 22 (fit unchecked), SureFire ProComp 556 Muzzle Brake, SureFire SOCOM 3-Prong Flash Hider, SureFire SOCOM 4-Prong Flash Hider, SureFire WARCOMP Flash Hider, Taurus TX22 Thread Protector, VG6 Precision GAMMA 556
M-LOK
- Hand stops
- BCM KAG (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK Hand Stop (fit unchecked), Magpul M-LOK Index Panel (fit unchecked)
- Vertical grips
- BCM Vertical Grip Mod 3 (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK MVG vertical grip (fit unchecked)
- Lights
- Cloud Defensive REIN (fit unchecked), Streamlight ProTac Rail Mount HL-X (fit unchecked), SureFire Mini Scout Light Pro (fit unchecked), SureFire Scout Light Pro Dual Fuel (fit unchecked)
- Rail sections
- Magpul M-LOK® Aluminum Rail, 3 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 5 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 7 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 9 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 11 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 3 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 5 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 7 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 9 Slots (fit unchecked)
- Adapter plates
- Magpul M-LOK Hand Stop MOE Adapter (fit unchecked)
- Sling mounts
- Magpul M-LOK QD Sling Mount (fit unchecked)
- Rail covers
- Magpul M-LOK Rail Cover Type 2
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Aerospace Arms $549.00 Nov 21, 2026, in stock that day
- Alexander's Store $581.99 Nov 18, 2026, in stock that day
- Nordic Components $658.00 Nov 21, 2026, in stock that day