Muzzle device
SureFire ProComp 556 Muzzle Brake
A stand-alone muzzle brake: two large windows through each side, flat port faces, two shallow pockets on the top and two on the bottom with a land between each pair, the top pair each drilled with a hole, and blind pilot holes at 3, 6 and 9 o'clock for tuning or for pinning. No suppressor mounts on it.

- Weight
- 3.4 oz Corroboratedpublished: KYGunCo, Surefire Procomp 556 Muzzle Break 1/2x28 - Black (its SPECIFICATIONS block, SureFire's sheet reprinted), a seller, read Oct 28, 2026
- Lowest price
- $74.99 at Primary Arms, read Nov 17, 2026
- Made for
- Caliber: 5.56 mm (.223 caliber)
- Maker's number
- PROCOMP-556-1/2-28
- Colour
- Black nitride
- Drawn as
- modelled
- Maker's page
- primaryarms.com
In “Aero 5.56 carbine”, a build on the start page, in place of its Mil-spec A2 flash hider, 1/2-28 (drawing 9349051).
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Overall length (rear face to front face)2.5 in ± 0.05 in 63.5 mmConflictPublished: KYGunCo, Surefire Procomp 556 Muzzle Break 1/2x28 - Black (its SPECIFICATIONS block, SureFire's sheet reprinted), a seller, read Oct 28, 2026
Published “LENGTH: 5.56 mm - 2.5 in (6.35 cm), 7.62 mm - 2.7 in (6.85 cm)” used
KYGunCo, Surefire Procomp 556 Muzzle Break 1/2x28 - Black (its SPECIFICATIONS block, SureFire's sheet reprinted), a seller, read Oct 28, 2026 the page, harvested Oct 28, 2026
The sheet's two models in one line; this is the 5.56's. SureFire's sheet adds that the length "may vary, depending on which SureFire adapter is used" (the discovery's reading of the sheet, which isn't on file).
Published “Length: 2.5 in”
Redcon1 Tactical, SureFire ProComp Muzzle Brake 5.56 - Black (its specification list, PROCOMP-556-1/2-28), a seller, read Oct 28, 2026 the page, harvested Oct 28, 2026
Published “Caliber: 5.56 mm (.223 caliber) Length: 2.5””
Primary Arms, SureFire ProComp Muzzle Brake - 1/2X28 (its feature list), a seller, read Oct 28, 2026 the page, harvested Oct 28, 2026
Published “Melonite Finish Length 2.67" Black Includes Crush Washer”
Cheaper Than Dirt, SureFire ProComp 5.56 Muzzle Brake 1/2"x28 (FC-084871323512), a seller, read Oct 28, 2026 the page, harvested Oct 28, 2026
One seller's own figure, 0.17 longer than the maker's; whether it counts a crush washer it says comes in the box, it doesn't say.
Photo 2.49 in ± 0.05 in
Primary Arms PROCOMP556-1-2-28_03, 2200 x 1467, harvested
Scale: its own collar's width, 438 px, as od (0.864) less the 2% a black edge reads thin on white (447 px). Read by the length between the end faces' centres (1287.5 px, each end face's ellipse halved), over the collar's width: 2.94 widths as read, 2.88 with the thin reading taken out
A check of the published length against the published width: 2.49 to 2.54 by how thin the photo reads the black collar.
SureFire's own sheet as KYGunCo reprints it; two more sellers (Redcon1, Primary Arms) say the same, and the photo's length over its width agrees. Cheaper Than Dirt's 2.67 is one seller's and stays visible.
kygunco and ctd differ by 0.17 in beyond what each states it is good to.
redcon1 and ctd differ by 0.17 in beyond what each states it is good to.
primary-arms and ctd differ by 0.17 in beyond what each states it is good to.
ctd and photo differ by 0.18 in beyond what each states it is good to.
Length ahead of the barrel's shoulder, installed (to the front face)2.5 in ± 0.05 in 63.5 mmProvisionalWorked out: {.overall_length}
Worked out 2.5 in used
{.overall_length}, harvested
The device's rear face on the barrel's shoulder.
No washer is drawn: one seller says one is in the box (Cheaper Than Dirt: "Includes Crush Washer"), SureFire's text as the others reprint it says nothing of how it is timed but its 6 o'clock pilot hole ("allows indexing the adapter at bottom dead center", Primary Arms), and no photo on file shows a washer. Seated on the shoulder, the device's own length is what it adds.
Largest outside diameter (the collar, and the lands at 12 and 6 o'clock the whole length)0.864 in ± 0.0005 in 21.9 mmCorroboratedPublished: Redcon1 Tactical, SureFire ProComp Muzzle Brake 5.56 - Black (its specification list, PROCOMP-556-1/2-28), a seller, read Oct 28, 2026
Published “Width: 0.864 in” used
Redcon1 Tactical, SureFire ProComp Muzzle Brake 5.56 - Black (its specification list, PROCOMP-556-1/2-28), a seller, read Oct 28, 2026 the page, harvested Oct 28, 2026
Photo 0.85 in ± 0.03 in
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
438 px at 515.0 px/in; a black edge on white reads up to 3% thin.
Photo 0.84 in ± 0.03 in
Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)
The collar, 411 px at 489.6 px/in.
The one published width (a seller's table: provisional). Both photos read it within their ±, 1.6% and 2.8% under, as a black part on white reads.
One diameter end to end: in the side view (_03) the outline's height is the collar's from the rear taper to the front face (438 to 442 px): the lands at the top and bottom are left round.
Across the two port flats (the 3 and 9 o'clock faces the windows are cut through)0.774 in ± 0.015 in 19.7 mmConflictPhoto: Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467
Photo 0.774 in ± 0.015 in used
Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)
The outline's width ahead of the collar, between the windows and ahead of them: 368 px for the collar's 411 (0.8954 of it), from the front face to row 788.
Photo 0.738 in ± 0.02 in
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
The flat facing the lens between the windows, read on its tone: an even dark (22 of 255) from column 1004 to 1232, a chord 228 px wide on a collar 438 across; a flat whose chord that is stands 0.854 of the radius out.
A silhouette, read square on. The other reading is a tone's edge, where the flat turns into the round; the two are 0.036 apart and stay visible.
below and side-chord differ by 0.036 in beyond what each states it is good to.
Port flats, rear end (from the rear face)1.187 in ± 0.012 in 30.1 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467
Photo 1.187 in ± 0.012 in used
Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)
The outline steps out to the collar's width at row 788, after a concave lit run-out over rows 760 to 788 (0.057).
Port flats, the round run-out at their rear end, along the device0.057 in ± 0.012 in 1.4 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467
Photo 0.057 in ± 0.012 in used
Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)
Rows 760 to 788: the cutter's round, drawn as a quarter circle.
Rear taper, where it begins (from the rear face)0.196 in ± 0.012 in 5 mmCorroboratedPhoto: Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467
Photo 0.196 in ± 0.012 in used
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
The outline narrows from row 1302; a straight cone (0.55 px of width a row) to the end face's ellipse.
Photo 0.182 in ± 0.012 in
Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)
From row 1280.
The larger view; the two are 0.014 apart, within their two ±.
Rear face, outside diameter (where the taper ends)0.754 in ± 0.015 in 19.2 mmCorroboratedPhoto: Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467
Photo 0.754 in ± 0.015 in used
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
The cone carried to the rear face's station: 0.873 of the collar's width.
Photo 0.748 in ± 0.015 in
Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)
0.866 of the collar's width.
The two agree within 0.006.
Grooves round the collar3ProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467
Photo 3 count used
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
Three notches in each edge of the outline, rows 1014 to 1126; three in the underside's (_02) at the same stations, and three in every three-quarter view.
Front groove, its middle (from the rear face)0.728 in ± 0.01 in 18.5 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467
Photo 0.728 in ± 0.01 in used
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
Row 1028, the notch's middle on both edges; the underside's outline has it at 0.727.
Grooves, middle to middle0.084 in ± 0.004 in 2.1 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467
Photo 0.0835 in ± 0.004 in used
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
Rows 1028, 1071 and 1114: 43 px apart.
Groove, width at the surface0.05 in ± 0.008 in 1.3 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467
Photo 0.05 in ± 0.008 in used
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
26 px between where each notch leaves the outline's edge; its floor is about half that (12 to 16 px): the walls lean.
Groove, depth0.018 in ± 0.004 in 0.5 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467
Photo 0.018 in ± 0.004 in used
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
9 px on the left edge (895 to 904) and 10 on the right (1331 to 1321), of a collar 438 across.
Port windows (each through from side to side)2ProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467
Photo 2 count used
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
Two openings in each port flat, the backdrop seen through both (rows 223 to 431 and 518 to 815); the underside's outline is notched at the same two places on each side, and every three-quarter view shows two a side.
Front window, rear edge (from the rear face)1.887 in ± 0.012 in 47.9 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467
Photo 1.887 in ± 0.012 in used
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
Row 431: where the near face's edge meets the window's rear wall (lit, seen from above as a band with the bore's hole in it).
Front window, front edge2.291 in ± 0.012 in 58.2 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467
Photo 2.291 in ± 0.012 in used
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
Row 223, where the backdrop first shows through.
Rear window, rear edge1.142 in ± 0.012 in 29 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467
Photo 1.142 in ± 0.012 in used
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
Row 815.
Rear window, front edge1.718 in ± 0.012 in 43.6 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467
Photo 1.718 in ± 0.012 in used
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
Row 518.
Windows, height across the port face (12 to 6 o'clock)0.584 in ± 0.015 in 14.8 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467
Photo 0.584 in ± 0.015 in used
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
296 px of the collar's 438.
Both windows the same, from column 971 to 1267. Their middle reads 6 px (0.012) above the outline's, as the 9 o'clock pilot hole's reads 12 px above it: the photo is turned a degree or two about the axis. Drawn on the axis: no source says the windows are off it (SureFire's "offset porting" is said of the bore, not drawn).
Windows, corner radius0.09 in ± 0.025 in 2.3 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467
Photo 0.09 in ± 0.025 in used
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
The see-through narrows over about 45 rows and 45 px at each end of each window.
Land between the two pockets (at 12 and at 6 o'clock), width0.088 in ± 0.012 in 2.2 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467
Photo 0.088 in ± 0.012 in used
Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)
Columns 1076 to 1118 (42 px), the darkest stripe down the underside, with the grooves across it.
Pockets, outer edge, out from the middle (as seen square on the face they are cut in)0.3 in ± 0.012 in 7.6 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467
Photo 0.3 in ± 0.012 in used
Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)
Columns 950 and 1236, 144.5 and 141.5 px from the outline's middle; outside them, the round down to the port flats (to 0.387).
Pockets, how far each floor is turned from the plane square to the land24° ± 6°ProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467
Photo 24 deg ± 6 deg used
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
The hole at the right edge, 25 px wide (columns 1293 to 1318) by 63 px along the device (rows 875 to 938): 0.40, a floor 66 degrees from the line of sight, 24 from square to the land. The floor's band beside the side view's edge (54 px, from 0.75 of the radius out) agrees with 15 to 25. And the underside (aa48bc88d85b) checks it: the grooves run on into each bottom pocket for 0.04 inside its outer edge (to column 974, 0.262 out, rows 1020 to 1112) and stop where the floor is as deep as a groove; a floor through the outer edge on the round, turned 24 degrees, is 0.016 deep at 0.262.
Each floor faces out and toward its own side. Read on the top-left pocket's hole, seen at the side view's edge: a round hole shows as an ellipse whose width over its height is the cosine of the angle between the floor and the line of sight.
Pockets, rear end (the round end's farthest point, from the rear face)0.347 in ± 0.012 in 8.8 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467
Photo 0.347 in ± 0.012 in used
Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)
Row 1199, both bottom pockets. The side view sees the bottom-left one's floor end at row 1200 (0.394) from its edge.
Behind the grooves, in the collar.
Pockets, front end (the round end's farthest point)2.245 in ± 0.02 in 57 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467
Photo 2.245 in ± 0.02 in used
Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)
Row 270: the round ends' tops, 0.255 behind the front face.
Blind pilot holes at 3 and 9 o'clock, diameter0.103 in ± 0.012 in 2.6 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467
Photo 0.103 in ± 0.012 in used
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
The 9 o'clock one: rows 905 to 957 (52 px) on a collar 438 across.
SureFire, as Piasa Armory, Midwest Gun Works and others reprint it: "Every ProComp features blind pilot holes at the 9 o’clock position to enable fine-tuning of recoil traits for individual shooting styles or ammunition characteristics. All that is required is a basic hand drill and appropriate drill bits." Primary Arms: "Blind pilot holes at the 3 and 9-o’clock positions". One shows on the left port face in _03 and on SureFire's picture of it on a rifle, one on the right in Primary Arms' _00.
Pilot holes, their middle (from the rear face)0.917 in ± 0.01 in 23.3 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467
Photo 0.917 in ± 0.01 in used
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
Row 931: behind the port flats, on the round between them and the grooves. The 3 o'clock one is drawn at the same station: Primary Arms' _00 shows it there to within its three-quarter view's reading.
Pilot holes, how deep (blind)0.04 in ± 0.03 in 1 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows how deep a blind pilot hole goes. A spot drill's depth, short of the thread's major diameter.
Worked out 0.04 in ± 0.03 in used
An assumption for the drawing, not a reading: no view on file shows how deep a blind pilot hole goes. A spot drill's depth, short of the thread's major diameter., harvested
NOT SOURCED: "blind" is the maker's word; no view looks into one.
Holes in the two top pockets, diameter0.124 in ± 0.012 in 3.1 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467
Photo 0.124 in ± 0.012 in used
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
The top-left pocket's, seen at the side view's edge: 63 px along the device (rows 875 to 938), its true diameter there.
One in each top pocket (counted on Primary Arms' _00 and _01, Rifle Supply's two photographs and SureFire's catalogue picture); none in the bottom pockets (_02, square on).
Top-left pocket's hole, its middle (from the rear face)0.965 in ± 0.012 in 24.5 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467
Photo 0.965 in ± 0.012 in used
Primary Arms PROCOMP556-1-2-28_03: the device standing muzzle up, square on its left side, from about 3.5 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1287.5 px, as overall_length (2.5): 515.0 px/in; across the device, its collar's width (438 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges and hole extents as read on those runs (± 3 px), stations from the rear face's centre (row 1403)
Row 906, 0.048 ahead of the 9 o'clock pilot hole.
Top-right pocket's hole, its middle (from the rear face)0.965 in ± 0.012 in 24.5 mmConflictWorked out: {.top_left_hole_x}
Worked out 0.965 in ± 0.012 in used
{.top_left_hole_x}, harvested
Photo 0.887 in ± 0.05 in
Primary Arms PROCOMP556-1-2-28_00: lying, front three-quarter from above its right side, 2200 x 1467, harvested
Scale: its own length along the axis in the picture as overall_length (2.5): about 611 px/in. Read by the holes' middles (picked on a crop at 1:1, ± 5 px) projected on the axis from the rear face's middle to the front face's: the right pocket's hole 0.03 behind the 3 o'clock pilot hole (taken at pilot_hole_x) and 0.13 behind the left pocket's
A three-quarter view sees two holes at different angles round the top as standing at different places along it: the 0.13 between them here is that, not a station's difference, if the patent's FIG. 4 holds for this product.
The maker's patent for this product draws the two ports at one station, and the one straight reading on file (the left one's) gives it. The oblique reading stays: a three-quarter view mixes an offset round the top into the stations along it.
patent and oblique differ by 0.078 in beyond what each states it is good to.
No straight view on file faces it. SureFire's patent-marking page lists US 7,954,414 and 8,205,538 against PROCOMP; the first draws its two top ports at one station (FIG. 4, ports 36 and 38; FIG. 7 the section through both) and says of them: "A first port may be offset from and to one side of the top of the body, and a second port offset from and to the opposite side of the top of the body by a transverse distance greater than the transverse distance by which the first port is offset" (column 2). That is SureFire's "offset porting": offset round the top, not along it.
First chamber (between the thread and the rear window), diameter, as drawn0.455 in ± 0.04 in 11.6 mmConfirmedWorked out: {.thread_minor_d}
Worked out 0.4551 in ± 0.04 in used
{.thread_minor_d}, harvested
SureFire's patent for it (US 7,954,414, which its marking page lists against PROCOMP): "a high pressure first chamber in the body extending along the axial passageway for receiving combustion gases from the muzzle", which "includes at least one port for venting a portion of the gases in the first chamber to directionally counter upward and sideward movement of the muzzle" (column 1 and 2): the top ports vent it. FIG. 6 draws it (32) about as wide as the threaded bore's minor diameter. No view on file looks into it: NOT SOURCED as a size.
First chamber, front end (where it turns down to the bore; from the rear face), as drawn1.006 in ± 0.05 in 25.6 mmProvisionalWorked out: {.window_rear_rear_x} - 0.157 * {.od}
Worked out 1.006 in ± 0.05 in used
{.window_rear_rear_x} - 0.157 * {.od}, harvested
NOT SOURCED as a size: the patent's FIG. 6 has the chamber end in a cone, and then a wall with the bullet's passage through it, ahead of which the first window opens. Drawn by that figure's proportions from the rear window's rear edge.
First chamber, the cone at its front end, length along the device, as drawn0.058 in ± 0.03 in 1.5 mmCorroboratedWorked out: 0.067 * {.od}
Worked out 0.058 in ± 0.03 in used
0.067 * {.od}, harvested
Pin-and-weld pilot hole at 6 o'clock, diameter0.088 in ± 0.012 in 2.2 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467
Photo 0.088 in ± 0.012 in used
Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)
Rows 1238 to 1280 (42 px) on a collar 411 across.
SureFire, as Piasa Armory reprints it: "Pilot hole located at 6 o’clock for pin-and-weld applications"; Primary Arms: "an additional pilot hole at the 6-o’clock allows indexing the adapter at bottom dead center".
Pin-and-weld hole, its middle (from the rear face)0.225 in ± 0.01 in 5.7 mmProvisionalPhoto: Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467
Photo 0.225 in ± 0.01 in used
Primary Arms PROCOMP556-1-2-28_02: the device standing muzzle up, square on its underside, from about 3 degrees above, 2200 x 1467, harvested
Scale: its length between the end faces' centres, 1224 px, as overall_length (2.5): 489.6 px/in; across the device, its collar's width (411 px) as od (0.864). Read by the silhouette's runs and the grey level row by row and column by column at a level of 200 of 255; edges as read on those runs (± 3 px), stations from the rear face's centre (row 1369)
Row 1259, on the land's line, in the collar behind the grooves and the pockets' round ends.
The thread it is cut for: major diameter0.496 in ± 0.0033 in 12.6 mmConfirmedStandard: US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213
Standard “1/2-28 UNEF-2A MAJOR DIA .4989/.4924” used
US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213, from the site owner
Its number names its thread: PROCOMP-556-1/2-28 (Redcon1: "Thread: 1/2 x 28 TPI"; Primary Arms: "Thread Pattern 1/2 X 28"). The Army barrel's 1/2-28, as the catalog's barrels are drawn.
The thread it is cut for: minor diameter0.455 in ± 0.002 in 11.6 mmConfirmedStandard: US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213
Standard “MINOR DIA .4551 MAX” used
US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213, from the site owner
The thread it is cut for: pitch0.036 in ± 0.00005 in 0.9 mmConfirmedStandard: US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213
Standard “1/2-28 UNEF-2A” used
US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213, from the site owner
Threaded hole's depth from the rear face, as drawn0.69 in ± 0.01 in 17.5 mmConfirmedWorked out: {a2-flash-hider.thread_depth}
Worked out 0.69 in ± 0.01 in used
{a2-flash-hider.thread_depth}, from the site owner
NOT SOURCED for this device: no page, drawing or photo on file shows how deep its thread goes. Drawn as deep as the Army compensator's, which the same barrels take: it then ends 0.23 behind the pilot holes.
Hole through the device ahead of the thread, as drawn0.244 in ± 0.008 in 6.2 mmProvisionalWorked out: {surefire-socom-3-prong.bore_d}
Worked out 0.244 in ± 0.008 in used
{surefire-socom-3-prong.bore_d}, harvested
NOT SOURCED for this device: the photos on file show the front face's hole only at a slant, where its far wall hides its edge. Drawn as the 3-prong's, the same maker's device for the same bullet.
Barrel thread length it takes, or is made forNo value yetMissingNo source yet
No source states it (no drawing, no manual on file): no thread_length on its interface.
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Muzzle thread
- Uppers
- Nordic Components 22RB .22 LR upper, 16", Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12", Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16"
- Barrels
- Aero Precision 16" 5.56 CMV barrel, mid-length, BCM Standard 11.5" Carbine Barrel, Stripped, BCM Standard 14.5" Mid Length Barrel, Stripped, BCM Standard 16" Mid Length Barrel, Stripped, Bear Creek Arsenal BC-15 5.56 NATO, 16" Parkerized M4 Barrel, 1:7 Twist, Mid-Length Gas System, Daniel Defense CHF Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 10.3", Faxon Firearms Duty Series Pencil Profile 16" Mid-Length 5.56 NATO AR15 Barrel, Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 13.9", Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 14.5", Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 16", Rosco Manufacturing Bloodline 10.5" M4 5.56 NATO, Rosco Manufacturing Bloodline 11.5" M4 5.56 NATO, Rosco Manufacturing Bloodline 12.5" M4 5.56 NATO
- Barrels
- Taurus TX22 4.6 in Threaded Barrel
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Primary Arms $74.99 Nov 17, 2026, in stock that day
- Mile High Shooting Accessories $89.00 Nov 21, 2026, in stock that day
- KYGUNCO $89.00 Nov 21, 2026, in stock that day
- Impact Guns $89.00 Nov 21, 2026, in stock that day
- Redcon1 Tactical $89.00 Nov 21, 2026, in stock that day
- Rifle Supply $76.99 Nov 21, 2026, out of stock that day
- Midwest Gun Works $89.00 Nov 21, 2026, out of stock that day
- AR15Discounts $89.00 Nov 21, 2026, out of stock that day
- Cheaper Than Dirt $89.00 Nov 21, 2026, out of stock that day
- Alexander's Store $89.00 Nov 18, 2026, out of stock that day
- Sportsman's Warehouse $99.99 Nov 21, 2026, out of stock that day