Barrel
Daniel Defense CHF Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 10.3"
Daniel Defense's 10.3 in government-profile barrel, stripped: cold hammer forged chrome moly vanadium steel (Primary Arms writes "41V50"; OperationParts, Botach and Alexander's "4150"), a chrome lined 5.56 NATO chamber and bore, 1:7 twist, a heavy phosphate finish, a carbine-length gas port on a .750 in journal, an A4 extension with M4 feed ramps, a 1/2-28 muzzle thread. Sold without a gas block or a muzzle device.

- Weight
- 18.4 oz ± 0.08 oz Conflictpublished: Primary Arms, Daniel Defense CHF Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 10.3" (SKU and MPN 07-077-16176-018), Features (its Specifications say "Weight 1.15 lbs"), a seller, read Oct 6, 2026Its sources span 18.32 oz to 32.08 oz.
- Lowest price
- $338.00 at Right To Bear, read Nov 21, 2026
- Made for
- Chambered in 5.56 NATO, 1:7 twist
- Maker's number
- 07-077-16176-018
- Colour
- Daniel Defense heavy phosphate
- Drawn as
- modelled
- Maker's page
- primaryarms.com
In “BCM 11.5 in carbine, suppressed”, a build on the start page, in place of its BCM Standard 11.5" Carbine Barrel, Stripped.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Barrel length as its maker states it10.3 in ± 0.05 in 261.6 mmCorroboratedPublished: Primary Arms, Daniel Defense CHF Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 10.3" (SKU and MPN 07-077-16176-018), Features (its Specifications say "Barrel Length 10.3"), a seller, read Oct 6, 2026
Published “10.3" cold hammer-forged barrel” used
Primary Arms, Daniel Defense CHF Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 10.3" (SKU and MPN 07-077-16176-018), Features (its Specifications say "Barrel Length 10.3"), a seller, read Oct 6, 2026 the page, harvested Oct 6, 2026
Published “Barrel Length 10.3″”
OperationParts, Daniel Defense 10.3″ 5.56mm GOV’T Carbine CHF Barrel – Stripped (07-077-16176-018), Specifications, a seller, read Oct 6, 2026 the page, harvested Oct 6, 2026
Published “Length 10.3"”
Right To Bear, Daniel Defense 10.3" 5.56 NATO CHF Carbine 1:7 Government AR-15 Barrel (07-077-16176-018), Barrel Specifications, a seller, read Oct 6, 2026 the page, harvested Oct 6, 2026
The seller on file whose page is the part's own; the others state the same 10.3.
The nominal length, on every seller's page; none says between which points. Taken from the barrel's breech face, as the catalog's 16 in barrels are (bca-556-16-mid-barrel.length's note). From the closed bolt's face, the Army's way, the barrel would be 0.126 shorter end to end (bca-556-16-mid-barrel.bolt_face_behind_breech): the maker's square-on picture is against that (overall_length), and what it leaves open is in the ± of every length scaled from this one.
The gas block journal's diameter0.75 in ± 0.0005 in 19 mmCorroboratedPublished: Primary Arms, Daniel Defense CHF Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 10.3" (SKU and MPN 07-077-16176-018), Specifications, a seller, read Oct 6, 2026
Published “Gas Seat Diameter .750” used
Primary Arms, Daniel Defense CHF Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 10.3" (SKU and MPN 07-077-16176-018), Specifications, a seller, read Oct 6, 2026 the page, harvested Oct 6, 2026
Published “Diameter At Gas Port .750″”
OperationParts, Daniel Defense 10.3″ 5.56mm GOV’T Carbine CHF Barrel – Stripped (07-077-16176-018), Specifications, a seller, read Oct 6, 2026 the page, harvested Oct 6, 2026
Published “Gas Block Journal 0.75”
AR15Discounts, Daniel Defense 10.3" 5.56 NATO CHF Carbine Length 1:7 Government Contour AR-15 Barrel - 07-077-16176-018 (its own number 7575), Additional information, a seller, read Oct 6, 2026 the page, harvested Oct 6, 2026
The seller on file whose page is the part's own, to three places; two more sellers state the same.
The barrel's tenon: its breech face behind the shoulder the extension's front face seats on0.62 in ± 0.001 in 15.7 mmConfirmedWorked out: {std.ar15.barrel_tenon_length}
Worked out 0.62 in ± 0.001 in used
{std.ar15.barrel_tenon_length}, from the site owner
The Army's drawing 8448549, .620 ±.001, in the standard's ledger.
The barrel extension's rear end behind the barrel's breech face0.501 in ± 0.01 in 12.7 mmProvisionalWorked out: {std.ar15.barrel_extension_behind_breech}
Worked out 0.501 in ± 0.01 in used
{std.ar15.barrel_extension_behind_breech}, harvested
The readings and their sources are in the standard's ledger (std.ar15.barrel_extension_length, std.ar15.barrel_tenon_length).
One extension for every 5.56 barrel in the catalog (std.ar15.barrel_extension_behind_breech: the reference CAD set's 1.121 less the Army's .620 tenon). This barrel's own pictures read its extension about 0.03 longer behind the flange than that set's (extension_rear_x).
The barrel's own length ahead of the extension's front face: the flange's front face to the muzzle9.68 in ± 0.05 in 245.9 mmCorroboratedWorked out: {.length} - {.tenon_length}
Worked out 9.68 in ± 0.05 in used
{.length} - {.tenon_length}, harvested
The ruler for every length read off the maker's square-on picture: both its ends show there (the flange's front face and the muzzle's), and neither the extension's own length nor where the breech lies inside it comes into it. The ± is the published length's.
End to end, the extension's rear end to the muzzle's face10.801 in ± 0.07 in 274.3 mmProvisionalWorked out: {.length} + {.extension_behind_breech}
Worked out 10.801 in ± 0.07 in used
{.length} + {.extension_behind_breech}, harvested
Photo 10.8 in ± 0.1 in
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: its barrel extension's diameter, 91.08 px between its edges at grey 200 (the mean over columns 16 to 84), as the Army's .999 (extension_od): 91.17 px/in. Read by its two ends, each a straight edge across the part: the rear end's at column 7.5 (within 0.4 px over rows 470 to 524), the muzzle's at 991.7 (rows 490 to 511: its rim is broken, and the rows outside those end 1.5 to 3 px short): 984.2 px
The ± is what the edges' grey leaves: 10.66 at 235, 10.83 at 170.
Photo 10.9 in ± 0.04 in
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: the thread's own stripes, 3.225 px apart (the peak of the spectrum of rows 478 to 518 over columns 942 to 986, 13.6 periods; 3.219 to 3.232 on three bands of rows), as 28 to the inch (thread_pitch): 90.3 px/in. Read by the same two ends, 984.2 px apart
A ruler at the muzzle end alone, along the barrel: the ± is its three bands' spread and a pixel at each end.
Lengths at the published length, taken from the breech face. The maker's square-on picture reads 10.80 by its extension and 10.90 by its thread's pitch: the published figure or a little more, and not the 10.675 a 10.3 from the bolt's face would make it.
The published 10.3 from the breech face, with the standard extension's 0.501 behind that. The maker's square-on picture is the check, by three rulers of its own. Its thread's stripes, 3.225 px apart, make it 10.90 end to end at 28 to the inch: 0.9% over, and 2.1% over what a 10.3 taken from the bolt's face would make it (10.675: bca-556-16-mid-barrel.bolt_face_behind_breech). Its extension's diameter as the Army's .999 makes it 10.80 with the edges read at grey 200 (10.66 at 235, 10.83 at 170, their 50% level). Its .750 journal makes it 10.95, 1.4% over: a dark tube reads thin on white (CLAUDE.md; BCM's barrel did the same by 2.5%), so the journal's scale is for diameters and the published length for lengths. The larger picture (0ec43808ddef) is no use here: taken from 16 in, its ends are their rims' arcs, and its lens draws the thread's pitch 4% short at the muzzle end.
The barrel extension's rear end, from the flange's rear face (negative: inside the receiver)-0.99 in ± 0.01 in -25.1 mmConflictWorked out: {std.ar15.barrel_extension_flange_thickness} - {std.ar15.barrel_extension_length}
Worked out -0.99 in ± 0.01 in used
{std.ar15.barrel_extension_flange_thickness} - {std.ar15.barrel_extension_length}, harvested
The reference CAD set's extension, 1.121 from its front face to its rear end, less its 0.131 flange.
Photo -1.026 in ± 0.015 in
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in. Read by the rear end's edge (column 7.5) to the flange's rear face (column 100.6: its lower edge, where the pin doesn't stand in front of it): 93.1 px
The standard's extension, as the receiver and the carrier are drawn for it; this barrel's pictures read it 0.036 longer, which stays here beside it.
model and photo differ by 0.036 in beyond what each states it is good to.
This barrel's own pictures read its extension 0.03 to 0.04 longer behind the flange than the reference CAD set's: 1.026 here, and 1.003 to 1.015 on the larger picture (178.2 px between its rear end's face, behind its rim's arc, and the flange's rear face, at the scales its extension's and its journal's diameters give there). The catalog's three 16 in barrels read 0.979, 0.984 and 0.996 by their photos. Drawn as the standard's: an extension is an interface part, and one barrel's two pictures 1.5 of their ± off isn't yet a different extension. Open (the part's gaps).
The extension flange's front face, ahead of its rear face (the flange's thickness)0.131 in ± 0.005 in 3.3 mmProvisionalWorked out: {std.ar15.barrel_extension_flange_thickness}
Worked out 0.131 in ± 0.005 in used
{std.ar15.barrel_extension_flange_thickness}, harvested
The reference CAD set's flange.
Photo 0.142 in ± 0.012 in
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in. Read by the flange's rear face (column 100.6) to its front face (column 113.5: both edges of the silhouette step there within 0.05 px of each other): 12.9 px
The standard's flange, which a barrel nut is drawn round; the picture reads a pixel more (0.011 in), inside its ±.
Where the barrel's own length begins: every position ahead of it is read from this face on the picture and added to it.
The barrel extension's flange, its diameter as the side pictures have it at the journal's scale1.187 in ± 0.008 in 30.1 mmCorroboratedPhoto: Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000
Photo 1.187 in ± 0.008 in used
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: its gas block journal's diameter, 67.44 px between its edges at grey 200 (the mean over columns 740 to 880), as the published .750 (journal_od): 89.91 px/in. Read by the silhouette's widest, columns 104 to 110: 106.75 px against the journal's 67.44 (ratio 1.5830)
Photo 1.189 in ± 0.004 in
Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333, harvested
Scale: its gas block journal's diameter, 131.70 px between its edges at grey 192, the edge's 50% level (the mean over columns 1525 to 1680), as the published .750 (journal_od): 175.60 px/in. Read by the silhouette's widest, columns 228 to 244: 208.80 px against the journal's 131.70 (ratio 1.5854)
The traced picture's own reading, which its outline is scaled by; the larger picture reads 0.002 more.
The traced outline's scale reference (the silhouette's greatest height). The extension reads 1.4% large at the journal's scale in both pictures (extension_od_photo): the flange as drawn is flange_d.
The barrel extension's body, its diameter (what goes into the receiver)0.999 in ± 0.001 in 25.4 mmProvisionalWorked out: {bcm-16-mid-barrel.extension_od}
Worked out 0.999 in ± 0.001 in used
{bcm-16-mid-barrel.extension_od}, from the site owner
The Army's limit on drawing 8448548 ("DIAMETER NOT TO EXCEED .9990 FOR THIS LENGTH AFTER ASSEMBLY AND BEFORE FINISH"), read for BCM's barrel and adopted there: its source is in that ledger.
The barrel extension's body as the side pictures have it at the journal's scale1.013 in ± 0.008 in 25.7 mmCorroboratedPhoto: Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000
Photo 1.013 in ± 0.008 in used
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: its gas block journal's diameter, 67.44 px between its edges at grey 200 (the mean over columns 740 to 880), as the published .750 (journal_od): 89.91 px/in. Read by the extension behind its flange, columns 16 to 84: 91.08 px against the journal's 67.44 (ratio 1.3506)
Photo 1.01 in ± 0.004 in
Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333, harvested
Scale: its gas block journal's diameter, 131.70 px between its edges at grey 192, the edge's 50% level (the mean over columns 1525 to 1680), as the published .750 (journal_od): 175.60 px/in. Read by the extension behind its flange, columns 70 to 185: 177.39 px against the journal's 131.70 (ratio 1.3469)
The traced picture's, the same one flange_od is read on, so that the two give the flange as drawn.
Not the extension's size (extension_od: it goes into a 1.000 bore): how much the extension reads large beside the barrel in a picture. 1.1 to 1.4% in two pictures from two cameras, as BCM's barrel read 1.2% in Primary Arms' photo: the phosphated barrel reads thin on white and the extension, another piece with another finish, less so. The flange as drawn takes this ratio out (flange_d).
The barrel extension's flange, its diameter as drawn1.171 in ± 0.012 in 29.7 mmProvisionalWorked out: {.flange_od} * {.extension_od} / {.extension_od_photo}
Worked out 1.171 in ± 0.012 in used
{.flange_od} * {.extension_od} / {.extension_od_photo}, harvested
The flange at the scale its own extension gives: the picture's flange against the picture's extension, times the Army's .999. The reference CAD set's flange is 1.170 across.
The chamber section, between the flange and its taper: its diameter0.993 in ± 0.004 in 25.2 mmCorroboratedPhoto: Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333
Photo 0.993 in ± 0.004 in used
Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333, harvested
Scale: its gas block journal's diameter, 131.70 px between its edges at grey 192, the edge's 50% level (the mean over columns 1525 to 1680), as the published .750 (journal_od): 175.60 px/in. Read by columns 265 to 355: 174.34 px against the journal's 131.70 (ratio 1.3238)
Photo 0.992 in ± 0.008 in
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: its gas block journal's diameter, 67.44 px between its edges at grey 200 (the mean over columns 740 to 880), as the published .750 (journal_od): 89.91 px/in. Read by columns 122 to 166: 89.16 px against the journal's 67.44 (ratio 1.3221)
The finer picture (176 px/in against 90); the square-on one reads 0.001 less.
Where the chamber section ends and its taper begins, ahead of the flange's rear face0.781 in ± 0.02 in 19.8 mmProvisionalPhoto: Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000
Photo 0.781 in ± 0.02 in used
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in. Read by the flange's front face (column 113.5) to where two lines through the silhouette's width meet, one over the chamber section (columns 124 to 166) and one over the taper (182 to 246): column 172.5, 0.650 in; ahead of the flange's front face as drawn (flange_front_x)
Where the taper ends and the section under the hand guard begins, ahead of the flange's rear face1.641 in ± 0.03 in 41.7 mmProvisionalPhoto: Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000
Photo 1.641 in ± 0.03 in used
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in. Read by the flange's front face (column 113.5) to where the line through the taper's width (columns 182 to 246) meets the one through the section ahead of it (262 to 400): column 250.5, 1.510 in; ahead of the flange's front face as drawn (flange_front_x)
The section under the hand guard, its diameter at its rear end (the taper's front end)0.688 in ± 0.004 in 17.5 mmCorroboratedPhoto: Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333
Photo 0.688 in ± 0.004 in used
Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333, harvested
Scale: its gas block journal's diameter, 131.70 px between its edges at grey 192, the edge's 50% level (the mean over columns 1525 to 1680), as the published .750 (journal_od): 175.60 px/in. Read by the line through the section's width over columns 530 to 1240 (129.82 px less 0.01751 a column, rms 0.13 px), at the taper's front end (column 511.5): 120.86 px against the journal's 131.70
Photo 0.687 in ± 0.008 in
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: its gas block journal's diameter, 67.44 px between its edges at grey 200 (the mean over columns 740 to 880), as the published .750 (journal_od): 89.91 px/in. Read by the line through the section's width over columns 262 to 626 (66.41 px less 0.0185 a column, rms 0.13 px), at the taper's front end (column 250.5): 61.78 px against the journal's 67.44
The finer picture; the square-on one reads 0.001 less.
This section is not a cylinder: it narrows toward the muzzle by 0.076 in over 4.3 in, in both pictures (a line through its width fits each to 0.15 px), from two cameras, one of them square on. A hammer-forged barrel's own taper, not the lens.
The section under the hand guard, its diameter at its front end (where the flare to the collar begins)0.612 in ± 0.004 in 15.5 mmCorroboratedPhoto: Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333
Photo 0.612 in ± 0.004 in used
Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333, harvested
Scale: its gas block journal's diameter, 131.70 px between its edges at grey 192, the edge's 50% level (the mean over columns 1525 to 1680), as the published .750 (journal_od): 175.60 px/in. Read by the same line at the flare's rear end (column 1277.5): 107.45 px against the journal's 131.70
Photo 0.607 in ± 0.008 in
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: its gas block journal's diameter, 67.44 px between its edges at grey 200 (the mean over columns 740 to 880), as the published .750 (journal_od): 89.91 px/in. Read by the same line at the flare's rear end (column 639.6): 54.58 px against the journal's 67.44
The finer picture; the square-on one reads 0.005 less, inside its ± of half a pixel.
The flare up to the collar: its knee behind the collar's rear corner0.34 in ± 0.02 in 8.6 mmProvisionalPhoto: Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333
Photo 0.34 in ± 0.02 in used
Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333, harvested
Scale: its gas block journal's diameter, 131.70 px between its edges at grey 192, the edge's 50% level (the mean over columns 1525 to 1680), as the published .750 (journal_od): 175.60 px/in. Read by the silhouette's width over columns 1150 to 1345 at grey 192: a line through the flare's straight end (columns 1306 to 1337: 0.725 px a column, 19.9° a side) meets the line through the section behind it (columns 1150 to 1234) at column 1282.4; the collar's full width begins at 1342.05 (collar_rear_x on the square-on picture): 59.65 px
The flare is a curve that straightens into a cone of 20° a side just behind the collar. Its knee is where the line through that straight end meets the line through the section under the hand guard; the curve runs flare_fillet either side of it.
The flare's curve: how far it runs either side of its knee0.219 in ± 0.04 in 5.6 mmProvisionalPhoto: Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333
Photo 0.219 in ± 0.04 in used
Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333, harvested
Scale: its gas block journal's diameter, 131.70 px between its edges at grey 192, the edge's 50% level (the mean over columns 1525 to 1680), as the published .750 (journal_od): 175.60 px/in. Read by a curve tangent to both lines (a parabola through their meeting point) fitted to the silhouette's width over columns 1150 to 1345: it leaves each line 38.5 px from the knee (rms 0.38 px over the 196 columns, against 2.07 with a sharp knee)
The flare's knee ahead of the flange's rear face5.984 in ± 0.03 in 152 mmProvisionalWorked out: {.collar_rear_x} - {.flare_length}
Worked out 5.984 in ± 0.03 in used
{.collar_rear_x} - {.flare_length}, harvested
Read on the square-on picture alone, where a pixel is 0.011 in and the curve is three dozen pixels long, a line through the whole flare (columns 646 to 668) meets the section behind it at 5.931: a shallower line through the curve, not this knee.
Where the flare ends at the collar's full diameter, ahead of the flange's rear face6.324 in ± 0.02 in 160.6 mmProvisionalPhoto: Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000
Photo 6.324 in ± 0.02 in used
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in. Read by the flange's front face (column 113.5) to where the line through the flare (columns 646 to 668) meets the collar's level (678 to 724): column 675.4, 6.193 in; ahead of the flange's front face as drawn (flange_front_x)
The collar behind the gas block journal, its diameter0.85 in ± 0.004 in 21.6 mmCorroboratedPhoto: Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333
Photo 0.85 in ± 0.004 in used
Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333, harvested
Scale: its gas block journal's diameter, 131.70 px between its edges at grey 192, the edge's 50% level (the mean over columns 1525 to 1680), as the published .750 (journal_od): 175.60 px/in. Read by columns 1350 to 1450: 149.23 px against the journal's 131.70 (ratio 1.1331)
Photo 0.848 in ± 0.008 in
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: its gas block journal's diameter, 67.44 px between its edges at grey 200 (the mean over columns 740 to 880), as the published .750 (journal_od): 89.91 px/in. Read by columns 678 to 724: 76.23 px against the journal's 67.44 (ratio 1.1304)
The finer picture; the square-on one reads 0.002 less.
The gas block journal's rear shoulder (the collar's front face) ahead of the flange's rear face6.943 in ± 0.02 in 176.4 mmProvisionalPhoto: Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000
Photo 6.943 in ± 0.02 in used
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in. Read by the flange's front face (column 113.5) to the collar's front face (column 731.45: both edges of the silhouette step there, 731.49 and 731.40): 6.812 in; ahead of the flange's front face as drawn (flange_front_x)
A gas block's rear face comes back to this shoulder (Murf's picture of the sibling sold with a block, 7a92aa7b5869, has it there). The catalog's mid-length barrels have theirs at 8.85 to 8.87: this one is 1.91 to 1.93 behind them.
The gas block journal's front end (where the barrel steps down) ahead of the flange's rear face8.802 in ± 0.02 in 223.6 mmProvisionalPhoto: Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000
Photo 8.802 in ± 0.02 in used
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in. Read by the flange's front face (column 113.5) to the step ahead of the journal (column 900.1: the upper edge at 900.35, the lower at 899.84): 8.671 in; ahead of the flange's front face as drawn (flange_front_x)
The journal is 1.86 long, as the catalog's mid-length barrels' are (1.87 on BCM's): long enough for a front sight base's two bands, which the maker fits to this barrel's sibling.
The gas port ahead of the flange's rear face7.226 in ± 0.03 in 183.5 mmProvisionalPhoto: Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333
Photo 7.226 in ± 0.03 in used
Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333, harvested
Scale: its gas block journal's diameter as the published .750 (131.70 px at grey 192: 175.60 px/in), for the port's distance from the collar's front face; that face is journal_rear_x, from the square-on picture. Read by the port's dark spot (centre column 1505.5, row 607: 63.5 px above the axis on a radius of 67, so 21 px nearer the lens than the axis, which from 16 in and 670 px off the lens's foot shows it 5.1 px further out than it is: column 1500.4) from the collar's front face (column 1449.8: its rim's arc fitted on the silhouette's upper and lower edges, 1449.2 and 1450.4): 50.6 px, 0.288 in; read without the two corrections, 0.277; taken as 0.283 and added to journal_rear_x
No page gives a distance (Primary Arms: "Carbine gas system"). The port is on top; only the larger picture, turned about 19° toward the lens, shows it: 0.283 ahead of the collar's front face (the Army's rifle barrel has .295 on 8448548, a mid-length chart .300, BCM's barrel 0.28). Checks: the catalog's three mid-length barrels have their ports at 9.13 to 9.17, 1.90 to 1.94 ahead of this one, where Aero's carbine-length gas tube is 2 in shorter than its mid-length one (9.75 and 11.75; its other page's "9.8" would make it 1.95). With that tube in BCM's gas block on this port, its rear end stands in the carrier key's socket, short of its bottom (the part's test). Right To Bear says "Dimpled? No", and the pictures show no dimple or flat under the journal.
The gas port's diameter0.07 in ± 0.0005 in 1.8 mmCorroboratedPublished: Charlie's Custom Clones, Daniel Defense DD new 10.3" Mk18 barrel virgin, .070" gas (its own number DD061281; MPN 07-077-16176-018), the page's title, a seller, read Oct 6, 2026
Published “Daniel Defense DD new 10.3" Mk18 barrel virgin, .070" gas” used
Charlie's Custom Clones, Daniel Defense DD new 10.3" Mk18 barrel virgin, .070" gas (its own number DD061281; MPN 07-077-16176-018), the page's title, a seller, read Oct 6, 2026 the page, harvested Oct 6, 2026
A seller's title, for the hole the model cuts.
Photo 0.064 in ± 0.008 in
Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333, harvested
Scale: its gas block journal's diameter, 131.70 px between its edges at grey 192, the edge's 50% level (the mean over columns 1525 to 1680), as the published .750 (journal_od): 175.60 px/in. Read by the port's dark spot along the barrel at half its depth of grey (columns 1500.2 to 1511.4 on row 606): 11.2 px; along the barrel it is not foreshortened
The one stated figure for this number, a seller's; the picture's spot agrees with it within its ± and not with .082.
No seller's table states one. Charlie's Custom Clones' title for this number says .070; a customer's review on Primary Arms' page says "Daniel Defense released two different types, one with a 0.070\" gas port and the other is 0.082\" gas port". The picture's spot is the smaller.
The diameter behind the muzzle thread0.74 in ± 0.005 in 18.8 mmCorroboratedPhoto: Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333
Photo 0.74 in ± 0.005 in used
Dirty Bird's copy of 07-077-16176-018_01, the series Primary Arms serves: the barrel from its right side on white, the muzzle at the right, 2000 x 1333, harvested
Scale: its gas block journal's diameter beside this section, 131.07 px at grey 192 over columns 1700 to 1775 (the journal reads 0.9% narrower there than at its rear end in this picture: its lower edge), as the published .750 (journal_od). Read by columns 1795 to 1835: 129.33 px (ratio 0.9867)
Photo 0.742 in ± 0.008 in
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: its gas block journal's diameter, 67.44 px between its edges at grey 200 (the mean over columns 740 to 880), as the published .750 (journal_od): 89.91 px/in. Read by columns 908 to 928: 66.69 px against the journal's 67.44 (ratio 0.9890)
The finer picture; the square-on one reads 0.002 more.
The last section before the shoulder, 0.38 long: 0.005 under the journal on the radius.
The muzzle shoulder ahead of the flange's rear face9.178 in ± 0.02 in 233.1 mmProvisionalPhoto: Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000
Photo 9.178 in ± 0.02 in used
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in. Read by the flange's front face (column 113.5) to the shoulder's face (column 934.25: both edges of the silhouette step there, 934.24 and 934.27): 9.047 in; ahead of the flange's front face as drawn (flange_front_x)
Where the thread begins: a muzzle device or its washer seats here. With the thread's length it adds up to the barrel's own length ahead of the flange (0.131 + 9.680 = 9.811). A relief groove a pitch wide shows between the shoulder and the first thread in both pictures; it isn't drawn.
The muzzle thread's length0.633 in ± 0.015 in 16.1 mmProvisionalPhoto: Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000
Photo 0.633 in ± 0.015 in used
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in. Read by the shoulder's face (column 934.25) to the muzzle's face (column 991.7): 57.45 px
Photo 0.636 in ± 0.012 in
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: the thread's own stripes, 3.225 px apart (the peak of the spectrum of rows 478 to 518 over columns 942 to 986, 13.6 periods), as 28 to the inch (thread_pitch). Read by the same 57.45 px: 17.8 pitches
At the scale every other length is read at; counted in its own pitches it is 0.003 more.
The Army's barrel has .63 from its shoulder to its muzzle (8448549 sheet 1).
The muzzle thread's major diameter (its crests)0.496 in ± 0.0033 in 12.6 mmConfirmedWorked out: {bcm-16-mid-barrel.thread_major_d}
Worked out 0.4957 in ± 0.0033 in used
{bcm-16-mid-barrel.thread_major_d}, from the site owner
"1/2-28 UNEF-2A MAJOR DIA .4989/.4924" on the Army's drawing 8448549, read for BCM's barrel: its source is in that ledger.
The Army barrel's 1/2-28 thread, for the 1/2 X 28 the sellers state: what the model's thread is drawn at, not a measurement of this barrel. The pictures' silhouette of the thread is 0.484 (the larger) and 0.473 (the square-on one) at the journal's scale, between its crests and its roots.
The muzzle thread's minor diameter (its roots)0.455 in ± 0.002 in 11.6 mmConfirmedWorked out: {bcm-16-mid-barrel.thread_minor_d}
Worked out 0.4551 in ± 0.002 in used
{bcm-16-mid-barrel.thread_minor_d}, from the site owner
"MINOR DIA .4551 MAX" on the same drawing, read for BCM's barrel.
The muzzle thread's pitch0.036 in ± 0.00005 in 0.9 mmCorroboratedPublished: Primary Arms, Daniel Defense CHF Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 10.3" (SKU and MPN 07-077-16176-018), Specifications (its Features say "Threaded 1/2x28"), a seller, read Oct 6, 2026
Published “Thread Pattern 1/2 X 28” used
Primary Arms, Daniel Defense CHF Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 10.3" (SKU and MPN 07-077-16176-018), Specifications (its Features say "Threaded 1/2x28"), a seller, read Oct 6, 2026 the page, harvested Oct 6, 2026
Photo 0.03555 in ± 0.0003 in
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in. Read by the thread's stripes along rows 478 to 518 over columns 942 to 986: the spectrum's peak at a period of 3.225 px (3.219 to 3.232 on three bands of rows; 13.6 periods)
The seller's statement for this barrel; its own picture reads the same pitch within half a percent.
28 threads to the inch by four sellers' statements (Primary Arms, OperationParts "1 ⁄ 2 × 28 TPI", Alexander's and AR15Discounts "1/2×28", Botach "1/2x28"). The maker's square-on picture resolves it: its stripes are 28.1 to the inch at the published length's scale.
The bore's diameter (across the lands)0.219 in ± 0.001 in 5.6 mmConfirmedWorked out: {bcm-16-mid-barrel.bore_d}
Worked out 0.219 in ± 0.001 in used
{bcm-16-mid-barrel.bore_d}, from the site owner
".219 DIA+.001" on the Army's drawing 8448549, read for BCM's barrel: its source is in that ledger.
The cartridge's, for the hole the barrel is drawn with: the sellers state "5.56 NATO" and no bore, so this is the Army barrel's for that cartridge and not a measurement of this one.
The barrel indexing pin's diameter0.125 in ± 0.002 in 3.2 mmProvisionalWorked out: {bcm-16-mid-barrel.index_pin_d}
Worked out 0.125 in ± 0.002 in used
{bcm-16-mid-barrel.index_pin_d}, from the site owner
The reference CAD set's pin, read for BCM's barrel: its source is in that ledger.
Photo 0.123 in ± 0.011 in
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in. Read by the pin on the upper edge behind the flange: its rear edge at column 88.3, its front edge at 99.4: 11.1 px
The standard part's size; this barrel's picture reads it within a pixel.
The barrel indexing pin's axis behind the flange's rear face0.074 in ± 0.012 in 1.9 mmProvisionalPhoto: Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000
Photo 0.074 in ± 0.012 in used
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: the flange's front face to the muzzle's face, 878.2 px (columns 113.5 and 991.7, the silhouette at grey 200), as barrel_ahead_of_flange (9.680: the published 10.3 less the Army's .620 tenon): 90.72 px/in. Read by the middle of the pin's two edges on the upper silhouette (columns 88.3 and 99.4: 93.85) to the flange's rear face (column 100.6): 6.75 px
The reference CAD set has 0.0765 (0.2075 behind the flange's front face). In the breech view (3e288080affe) the pin stands against the flange's rear face.
The barrel indexing pin's top above the bore's axis0.581 in ± 0.008 in 14.8 mmProvisionalPhoto: Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000
Photo 0.581 in ± 0.008 in used
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, the muzzle at the right, 1000 x 1000, harvested
Scale: the flange's own radius in the same picture, 53.38 px at grey 200, as half of flange_d (0.5855). Read by the pin's top on the upper silhouette (rows 443.4 to 443.7 over columns 90 to 96) above the axis (row 496.5 there): 53.0 px, 0.993 of the flange's radius
A hair under the flange's rim: in the square-on picture the pin's top is 0.4 px lower than the flange's.
The barrel extension's rear opening, its diameter at the rear face0.77 in ± 0.005 in 19.6 mmProvisionalWorked out: {bcm-16-mid-barrel.extension_mouth_d}
Worked out 0.77 in ± 0.005 in used
{bcm-16-mid-barrel.extension_mouth_d}, from the site owner
The inside of a mil-spec extension as the reference CAD set has it, read for BCM's barrel (its source is in that ledger), for how the rear end looks: the breech view (3e288080affe) shows this barrel's lugs and its two M4 feed ramps. Appearance only.
The circle the extension's locking lugs leave between their tips0.572 in ± 0.003 in 14.5 mmProvisionalWorked out: {bcm-16-mid-barrel.extension_lug_bore_d}
Worked out 0.572 in ± 0.003 in used
{bcm-16-mid-barrel.extension_lug_bore_d}, from the site owner
The locking lugs' front faces, ahead of the extension's rear end0.214 in ± 0.005 in 5.4 mmProvisionalWorked out: {bcm-16-mid-barrel.extension_lug_depth}
Worked out 0.214 in ± 0.005 in used
{bcm-16-mid-barrel.extension_lug_depth}, from the site owner
The recess ahead of the lugs, which the bolt's lugs turn in: its diameter0.83 in ± 0.003 in 21.1 mmProvisionalWorked out: {bcm-16-mid-barrel.extension_recess_d}
Worked out 0.83 in ± 0.003 in used
{bcm-16-mid-barrel.extension_recess_d}, from the site owner
The recess's front end, ahead of the extension's rear end0.595 in ± 0.005 in 15.1 mmProvisionalWorked out: {bcm-16-mid-barrel.extension_recess_depth}
Worked out 0.595 in ± 0.005 in used
{bcm-16-mid-barrel.extension_recess_depth}, from the site owner
The barrel extension's locking lugs: how many8ProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part
Model 8 count ± 0 count used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part, from the site owner
Read by eight cylinder faces of radius .2860 about the bore, each 20° of the turn, at every 45° from the indexing pin's side: a lug under the pin, a slot half way to the next
The standard extension's, for how this barrel's rear end looks (the sellers: "A4 barrel extension", "Feed Ramps M4"); its own breech view (3e288080affe) shows five of them on the far side of the opening, the near ones behind the wall, and can't count the turn. The reference CAD set: a model source, never authoritative.
The lugs' rear faces: how far ahead of the extension's rear end the cone from the opening's radius comes down to the lugs' tips0.099 in ± 0.003 in 2.5 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part
Model 0.099 in ± 0.003 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part, from the site owner
Read by the cone (45°) from radius .3850 at the rear end, 1.121, to the lug tips' cylinder of radius .2860, which begins at 1.022
The slots between the extension's locking lugs: their width0.124 in ± 0.002 in 3.1 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part
Model 0.124 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part, from the site owner
Read by each slot's two flanks are planes along the axis, parallel to the slot's own radius and 0.0620 from the bore's axis either side of it (sixteen planes, their normals at 22.5° and every 45° on); they run from the lugs' front faces, 0.907, to the rear end
The slots between the lugs: their floor, from the bore's axis0.38 in ± 0.002 in 9.7 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part
Model 0.38 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part, from the site owner
Read by each slot's floor is a plane 0.3800 from the bore's axis, square to the slot's radius (eight planes); its corners are at radius .3850, the rear opening's
The M4 feed ramps: the diameter of the cylinder each is cut as0.28 in ± 0.002 in 7.1 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part
Model 0.28 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part, from the site owner
Read by two cylinders of radius 0.1400, between 0.937 and the rear end
The sellers: "Feed Ramps M4" (Primary Arms), "A4 with extended M4 feed ramps" (Alexander's). Two bright cuts through the rear end's lower rim in the breech view (3e288080affe), as the reference set has them.
The feed ramps: how far each cylinder's axis leans from the bore's45° ± 0.1°ProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part
Model 45 deg ± 0.1 deg used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part, from the site owner
Read by each axis lies in the plane of the bore's axis and one of the two slots either side of the bottom (opposite the pin), direction (±0.2706, -0.6533, 0.7071): 45° to the bore, coming toward it going forward
The feed ramps: each cylinder's axis from the bore's axis at the extension's rear end0.286 in ± 0.002 in 7.3 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part
Model 0.286 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec part, from the site owner
Read by each axis is 0.2860 from the bore's at the rear end (1.121), 0.1870 at 1.022 and 0.0720 at the lugs' front faces (0.907)
The flange's front face in the traced outline's own frame (from the extension's rear end, at the journal's scale)1.189 in ± 0.019 in 30.2 mmProvisionalPhoto: Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, on white, 1000 x 1000
Photo 1.189 in ± 0.019 in used
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, on white, 1000 x 1000, harvested
Scale: scale from daniel-defense-103-barrel.flange_od = 1.187 in (y-extent 106 px → 89.3 px/in). Read by x_max in y [-0.58, -0.53] of the traced outline (tools/trace.py); the flange's front face in the outline's own frame (from the extension's rear face, at the journal's scale): where the barrel's own length begins
The muzzle's face in the traced outline's own frame (from the extension's rear end, at the journal's scale)11.006 in ± 0.076 in 279.6 mmProvisionalPhoto: Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, on white, 1000 x 1000
Photo 11.006 in ± 0.076 in used
Botach's page for 07-077-16176-018: the maker's own square-on picture of the barrel from its right side, on white, 1000 x 1000, harvested
Scale: scale from daniel-defense-103-barrel.flange_od = 1.187 in (y-extent 106 px → 89.3 px/in). Read by x_max of the traced outline (tools/trace.py); the muzzle's face in the outline's own frame (from the extension's rear face, at the journal's scale)
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Barrel extension
- Uppers
- Aero Precision M4E1 Enhanced Upper Receiver Stripped, Aero Precision M4E1 Threaded upper receiver, BCM M4 Upper Receiver Assembly (w/ Laser T-Markings), Expo Arms 7075 Stripped AR-15 Upper Receiver, Geissele Automatics Super Duty Stripped Upper Receiver, Palmetto State Armory AR-15 Stripped Upper Receiver
Muzzle thread
- Muzzle devices
- Dead Air XRF Xeno Rimfire Muzzle Brake, HUXWRX Flash Hider-QD 556 1/2x28 (fit unchecked), Mil-spec A2 flash hider, 1/2-28 (drawing 9349051), Nordic Components 1/2-28 thread protector (ships on the 22RB), Otter Creek Labs Polonium, Otter Creek Labs Polonium K, Precision Armament M4-72 Severe-Duty® Compensator, SilencerCo Sparrow 22 (fit unchecked), SureFire ProComp 556 Muzzle Brake, SureFire SOCOM 3-Prong Flash Hider, SureFire SOCOM 4-Prong Flash Hider, SureFire WARCOMP Flash Hider, Taurus TX22 Thread Protector, VG6 Precision GAMMA 556
Gas block journal
- Gas blocks
- Aero Precision .750 low profile gas block, BCM Front Sight Base F - FSB (ID .750) - Milspec for Flat Top Uppers, BCM Low Profile Gas Block (steel with set screws) 750, SLR Rifleworks Sentry 7 Set Screw Adjustable Gas Block, Superlative Arms .750" Adjustable Gas Block, Bleed Off - Set Screw
Gas system length
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Right To Bear $338.00 Nov 21, 2026, in stock that day
- MidwayUSA $365.00 Nov 21, 2026, in stock that day
- AR15Discounts $327.00 Nov 21, 2026, out of stock that day
- Dirty Bird Industries $327.00 Nov 21, 2026, out of stock that day
- Primary Arms $348.00 Nov 21, 2026, out of stock that day
- Alexander's Store $365.00 Nov 18, 2026, out of stock that day