Muzzle device
Mil-spec A2 flash hider, 1/2-28 (drawing 9349051)
The M16A2's flash hider, which the Army's drawings call the compensator: five slots over the top and sides, closed underneath, on a .500-28 thread with its laminated spacer. Any maker's A2 built to drawing 9349051; the catalog part is the drawing's.

- Weight
- 2.1 oz ± 0.2 oz Conflictpublished: Spike's Tactical (its A2 flash hider, 1/2x28, "Mil-Spec Heavy Phosphate Finish"), the maker, read Oct 1, 2026
- Lowest price
- $6.30 at Primary Arms, read Nov 21, 2026
- Colour
- Phosphate, black
- Drawn as
- modelled
In “22RB carbine, scoped”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Compensator, overall length (rear face to front face)1.75 in ± 0.01 in 44.4 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “1.76 -.02, from the rear face (datum A)” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Published “Length: 1.75" Length”
Spike's Tactical (its A2 flash hider, 1/2x28, "Mil-Spec Heavy Phosphate Finish"), the maker, read Oct 1, 2026 the page, harvested Oct 1, 2026
Published “Overall Length- 1.750"”
KAK Industry (its A2 birdcage flash hider, "Phosphate Coated"), the maker, read Oct 1, 2026 the page, harvested Oct 1, 2026
The drawing; two makers' own pages state the same.
Makers of A2s state the same length: Spike's, Faxon, KAK, Ballistic Barn and Wing Tactical's listings of Aero's and Spike's all say 1.75 in.
Largest outside diameter (the rear section and the front ring)0.862 in ± 0.002 in 21.9 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.864 -.004 Ø (datum C)” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Published “Diameter: 0.86"”
Wing Tactical (Aero Precision's A2 birdcage flash hider, "Mil-Spec Heavy Phosphate"), a seller, read Oct 1, 2026 the page, harvested Oct 1, 2026
The drawing; a retailer's figure for Aero's agrees.
Dimensioned at the front end, where its extension lines leave the outline; the rear section is drawn at the same height, and on Windham's part the front ring measures 0.867 ± 0.007 against the rear section taken as this (tools/turned.py: 223.7 px against 222.4): the same within the ±.
Slotted cage, outside diameter (between the rear section and the front ring)0.834 in ± 0.01 in 21.2 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.844 -.020 Ø” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Photo 0.833 in ± 0.006 in
Windham Weaponry A2 flash hider, their part 9349051; straight side view on white, 1000 x 600, harvested
Scale: the same part's rear section in the same photo, taken as od (.862): 222.4 px radius on both lands, top and bottom (516 px/in). Read by tools/turned.py: radius from the part's own axis (a line through the mid-heights of the lands and the front ring; tilt 0.12°), 50% edges
On the closed side, where no slot cuts the edge: 214.97 px over the cage's middle 0.6 in (spread 0.1). The top edge there is the top slot's rim (213.5 px), not the cage.
The drawing. A real part's photo reads the same to 0.001.
Which section this callout belongs to isn't plain from the scan: its extension lines run just inside the .864's, and the outline is drawn almost at one height throughout (310 px over the rear section, 308 over the cage, where .020 in would be 7 px). It is the cage: on a real part the cage is the smaller section (windham), and the drawing's 43° chamfer is called out in 2 PLACES, one at each end of it. First read as the front ring's and corrected before anything was built on it.
Steps at the two ends of the cage, chamfer angle (from square to the axis)45° ± 2°ConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “43° +4°, 2 PLACES” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Rear section, length (rear face to the step down to the cage)0.72 in ± 0.01 in 18.3 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.73 -.02” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
The section with the wrench flats and the two grooves. On Windham's part the step is 0.120 ahead of the second groove's front wall, where these callouts put it (.73 less .49 less .11) at 0.13.
Slotted cage, length (between its two steps)0.8 in ± 0.01 in 20.3 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.79 +.02” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Photo 0.813 in ± 0.005 in
Windham Weaponry A2 flash hider, their part 9349051; straight side view on white, 1000 x 600, harvested
Scale: the same part's rear section in the same photo, taken as od (.862): 222.4 px radius on both lands, top and bottom (516 px/in). Read by tools/turned.py: radius from the part's own axis (a line through the mid-heights of the lands and the front ring; tilt 0.12°), 50% edges
Between the two places the closed side's edge crosses the level midway between the rear section's radius and the cage's: 419.5 px.
The drawing; the photo agrees within the two ±.
Grooves in the rear section, width (two, full-radius bottoms)0.12 in ± 0.01 in 3 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.11 +.02, 2 PLACES; FULL R, 2 PLACES” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Photo 0.128 in ± 0.006 in
Windham Weaponry A2 flash hider, their part 9349051; straight side view on white, 1000 x 600, harvested
Scale: the same part's rear section in the same photo, taken as od (.862): 222.4 px radius on both lands, top and bottom (516 px/in). Read by tools/turned.py: radius from the part's own axis (a line through the mid-heights of the lands and the front ring; tilt 0.12°), 50% edges
Wall to wall just under the lands' surface (0.007 in below it): 0.129 and 0.127. That high up a broken edge (.005 +.010) is still part of it, so it reads the groove a little wide.
The drawing; the photo agrees within the two ±.
Grooves in the rear section, diameter at their bottoms0.62 in ± 0.01 in 15.7 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.63 -.02 Ø, 2 PLACES” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Photo 0.617 in ± 0.007 in
Windham Weaponry A2 flash hider, their part 9349051; straight side view on white, 1000 x 600, harvested
Scale: the same part's rear section in the same photo, taken as od (.862): 222.4 px radius on both lands, top and bottom (516 px/in). Read by tools/turned.py: radius from the part's own axis (a line through the mid-heights of the lands and the front ring; tilt 0.12°), 50% edges
On the top edge: 159.0 and 159.7 px (0.616, 0.619). The bottom edge in the grooves stops 18.5 px short of that (177.6 px), near-black: read as a shadow under the part, since a turned groove has one radius; not used.
The drawing; the photo agrees to 0.003.
First groove's rear edge, from the rear face0.22 in ± 0.01 in 5.6 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.23 -.02” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Second groove's rear edge, from the rear face0.48 in ± 0.01 in 12.2 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.49 -.02” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
On Windham's part the two grooves' rear walls are 0.257 apart; these callouts make it .26.
Wrench flats, across (two, on the rear section)0.74 in ± 0.01 in 18.8 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.75 -.02 (rear end view)” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Dimensioned on the rear end view between two chords, left and right. That they run from the rear face to the first groove is read from the side view, where their edges show as two lines 0.22 in either side of the axis over that length (a .75 chord of a .864 circle is 0.21 from the centre).
Rear face's edge, chamfer0.03 in ± 0.01 in 0.8 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.02 +.02 X 45°, 2 PLACES” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Front face's edge, chamfer0.04 in ± 0.01 in 1 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.03 +.02 X 45°” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Slots5ConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “5 SLOTS” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Slots, angle between neighbours45°ConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “45° (basic), 4 PLACES” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
The front end view shows them at the top, 45° and 90° either side of it; nothing in the lower half.
Slots, radius of the cut along the body0.5 in ± 0.01 in 12.7 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.49 +.02 R, 5 PLACES” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Slots, centre of the cut's radius from the axis0.61 in ± 0.005 in 15.5 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.610 ± .005, 5 PLACES” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Slots, centre of the cut's radius behind the front face0.59 in ± 0.005 in 15 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.590 ± .005, 5 PLACES” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Slots, width0.185 in ± 0.01 in 4.7 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.175 +.020, 5 PLACES (Section B-B)” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Section B-B gives two widths and an angle: .175, .08 and 28°. Read as a cutter .175 thick whose rim narrows at 28° included to a .08 flat: that is the only arrangement in which the three agree (.175 less .08 is twice 0.19 × tan 14°), and it is the shape the side view draws face-on: a slot .08 wide at its ends that opens to full width along its middle. The drawing doesn't say it in words.
Slots, width at the cut's deepest edge0.09 in ± 0.01 in 2.3 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.08 +.02, 5 PLACES (Section B-B)” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Slots, included angle between the walls near the cut's deepest edge30° ± 2°ConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “28° +4°, 5 PLACES (Section B-B)” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Bore through the slotted body and the front face0.67 in ± 0.01 in 17 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.66 +.02 Ø (Section A-A)” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
That bore's depth from the front face0.88 in ± 0.01 in 22.4 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.87 +.02 (Section A-A)” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Section A-A: from the front face back to where the 94° cone meets the bore.
Cone behind that bore, included angle90° ± 4°ConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “94° -8° (Section A-A)” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Hole between the thread and the cone0.343 in ± 0.005 in 8.7 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.338 +.010 (Section A-A)” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Threaded bore's depth from the rear face0.69 in ± 0.01 in 17.5 mmConfirmedStandard: US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.68 +.02 (Section A-A)” used
US Army TDP drawing 9349051 (Compensator), sheet 1 of 1, rev E; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
The thread is .500-28 UNEF-2B MOD with .62 MIN FULL THREAD: it takes the AR-length muzzle thread. A barrel's thread longer than this would bottom before the spacer is clamped.
Spacer, outside diameter0.74 in ± 0.01 in 18.8 mmConfirmedStandard: US Army TDP drawing 9349052 (Spacer, Compensator), sheet 1 of 1, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.75 -.02 Ø” used
US Army TDP drawing 9349052 (Spacer, Compensator), sheet 1 of 1, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Spacer, inside diameter0.515 in ± 0.005 in 13.1 mmConfirmedStandard: US Army TDP drawing 9349052 (Spacer, Compensator), sheet 1 of 1, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.510 +.010 Ø (datum A)” used
US Army TDP drawing 9349052 (Spacer, Compensator), sheet 1 of 1, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Spacer, thickness as supplied (solid stock and all its laminations)0.07 in ± 0.0045 in 1.8 mmConfirmedStandard: US Army TDP drawing 9349052 (Spacer, Compensator), sheet 1 of 1, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “.075 -.009” used
US Army TDP drawing 9349052 (Spacer, Compensator), sheet 1 of 1, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
Spacer, thickness of its solid stock (every lamination peeled)0.033 in ± 0.0025 in 0.8 mmConfirmedStandard: US Army TDP drawing 9349052 (Spacer, Compensator), sheet 1 of 1, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file
Standard “035 -.005 SOLID STOCK; 16-18 LAMINATIONS (.002) THICK” used
US Army TDP drawing 9349052 (Spacer, Compensator), sheet 1 of 1, rev F; user-supplied scan (Distribution Statement F, Colt proprietary notice), a copy on file, from the site owner
The scan shows no decimal point before the 035. It is .035: 16 to 18 laminations of .002 on .030 to .035 make .062 to .071, against the .066 to .075 given for the whole.
Spacer, thickness installed0.052 in ± 0.022 in 1.3 mmProvisionalWorked out: Between spacer_thickness_solid at its least (.030) and spacer_thickness_supplied at its most (.075): the midpoint, ± half the range.
Worked out 0.0525 in ± 0.0225 in used
Between spacer_thickness_solid at its least (.030) and spacer_thickness_supplied at its most (.075): the midpoint, ± half the range., from the site owner
Laminations are peeled until the compensator tightens with its closed side down, so the installed thickness is whatever that barrel's thread needs: anywhere from the solid stock to the full stack. The value is the middle of that range and the ± covers all of it.
Length ahead of the barrel's shoulder, installed (to the front face; the spacer's thickness included)1.802 in ± 0.025 in 45.8 mmProvisionalWorked out: {.spacer_thickness} + {.compensator_length}
Worked out 1.8025 in used
{.spacer_thickness} + {.compensator_length}, from the site owner
The spacer against the shoulder, the compensator against the spacer.
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Muzzle thread
- Uppers
- Nordic Components 22RB .22 LR upper, 16", Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12", Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16"
- Barrels
- Aero Precision 16" 5.56 CMV barrel, mid-length, BCM Standard 11.5" Carbine Barrel, Stripped, BCM Standard 14.5" Mid Length Barrel, Stripped, BCM Standard 16" Mid Length Barrel, Stripped, Bear Creek Arsenal BC-15 5.56 NATO, 16" Parkerized M4 Barrel, 1:7 Twist, Mid-Length Gas System, Daniel Defense CHF Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 10.3", Faxon Firearms Duty Series Pencil Profile 16" Mid-Length 5.56 NATO AR15 Barrel, Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 13.9", Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 14.5", Geissele Automatics CHF Chrome Lined Barrel - 5.56 - 16", Rosco Manufacturing Bloodline 10.5" M4 5.56 NATO, Rosco Manufacturing Bloodline 11.5" M4 5.56 NATO, Rosco Manufacturing Bloodline 12.5" M4 5.56 NATO
- Barrels
- Taurus TX22 4.6 in Threaded Barrel
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Primary Arms $6.30 Nov 21, 2026, in stock that day
- KAK Industry $7.00 Nov 21, 2026, in stock that day
- BCM $8.00 Nov 21, 2026, in stock that day
- Faxon Firearms $9.99 Nov 21, 2026, in stock that day
- Aero Precision $10.00 Nov 21, 2026, stock not said