Upper
Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12"
The 12 in AR57: a dedicated 5.7x28mm upper for a mil-spec AR-15 lower, a blowback monobloc receiver with its 12 in barrel inside its M-LOK handguard, a perforated brake on 1/2x28 behind a jam nut at the handguard's lip, its own bolt, handle and buffer, a 13-slot rail over the handle and 3-slot rails above and below the handguard's front block. FN's P90 magazine lies along its top (it ships with one) and it ejects down through the lower's magazine well. Primary Arms: "intended only for an AR pistol or a legally registered short-barreled rifle" (of its 12 in barrel). No maker's page is on file.

- Weight
- 48 oz ± 8 oz Provisionalpublished: AR Five Seven Center (ar-57center.com), home page: Cartridge 5.7×28mm NATO Capacity 50 Rounds Upper Weight ~3 lbs Full Build ~6 lbs Barrel Options 12″ / 16″, a seller, read Oct 18, 2026
- Lowest price
- Sold in the Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12", not by itself
- Made for
- The Panzer Arms AR57 ULT Complete AR-15 Upper Receiver converts any mil-spec AR-15 lower to fire 5.7x28mm ammunition (Primary Arms' description of the 12 in; its specifications: Caliber Gauge 5.7X28mm)
- Maker's number
- AR57ULT-12
- Colour
- Black (placeholder)
- Drawn as
- modelled
- Maker's page
- primaryarms.com
In “AR57 16 in, 5.7x28”, a build on the start page, in place of its Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16".
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Barrel length (the listing's own figure)12 in ± 0.5 in 304.8 mmCorroboratedPublished: Primary Arms, Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12" (AR57ULT-12), Specifications, a seller, read Oct 18, 2026
Published “Barrel Length 12” used
Primary Arms, Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12" (AR57ULT-12), Specifications, a seller, read Oct 18, 2026 the page, harvested Oct 18, 2026
Published “Barrel Length 12"”
KYGUNCO, Panzer Arms AR57 ULT 12 inch Complete Upper (PNZ-AR57ULT-12), specifications, a seller, read Oct 18, 2026 the page, harvested Oct 18, 2026
Both sellers give 12; Primary Arms' specifications table is the listing's own figure.
The handguard as the listing names it12 in ± 0.5 in 304.8 mmProvisionalPublished: Primary Arms, AR57ULT-12, Specifications, a seller, read Oct 18, 2026
Published “Handguard 12 in Freefloat Rail” used
Primary Arms, AR57ULT-12, Specifications, a seller, read Oct 18, 2026 the page, harvested Oct 18, 2026
What the 12 spans isn't said: the photo's handguard runs 10.6 in from its seam (6.84) to its front lip (17.45), and the receiver and handguard together 19.2 from the rail block's rear.
The brake's front end ahead of the takedown pin19.58 in ± 0.015 in 497.3 mmProvisionalWorked out: Read on a copy on file (the traced outline's x max (2101 px, the brake's prongs) on the brake's near side (0.31 in out)) through the camera fitted to it (the header): 19.86 in batch 10's pin frame.
Worked out 19.58 in ± 0.015 in used
Read on a copy on file (the traced outline's x max (2101 px, the brake's prongs) on the brake's near side (0.31 in out)) through the camera fitted to it (the header): 19.86 in batch 10's pin frame., harvested
The brake's front end as the trace's frame reads it (the outline's map's other end: muzzle_end_x)19.58 in ± 0.015 in 497.3 mmConflictWorked out: {.muzzle_end_x}
Photo 19.681 in ± 0.015 in
Primary Arms AR57ULT-12_02.jpg, the right side straight on, 2200 x 1467, harvested
Scale: its lug holes' near rims (takedown 243.5, 860.8; pivot 845.0, 864.5 px) as std.ar15.pin_spacing: 94.36 px/in. Read by the traced outline's x max (profiles.side), the brake's prongs at 2101 px
Worked out 19.58 in used
{.muzzle_end_x}, harvested
The trace reads the photo through its camera; the near rims' frame's reading (pinframe) is kept as it was read.
pinframe and camera differ by 0.101 in beyond what each states it is good to.
The handguard's front end as the trace's frame reads it (where the traced outline is clipped: the barrel, the nut and the brake are the model's)17.202 in ± 0.03 in 436.9 mmConflictWorked out: {.handguard_front_x}
Photo 17.308 in ± 0.02 in
Primary Arms AR57ULT-12_02.jpg, the right side straight on, 2200 x 1467, harvested
Scale: its lug holes' near rims (takedown 243.5, 860.8; pivot 845.0, 864.5 px) as std.ar15.pin_spacing: 94.36 px/in. Read by on a 3x crop the lip's front face meets the nut at 1877 px
Worked out 17.202 in used
{.handguard_front_x}, harvested
The trace reads the photo through its camera; the near rims' frame's reading (pinframe) is kept as it was read.
pinframe and camera differ by 0.106 in beyond what each states it is good to.
How many slots the receiver's top rail has13ProvisionalPhoto: a photo on file
Photo 13 count used
a photo on file, harvested
Scale: none: a count. Read by thirteen dips in the tooth tops along the rail (every pixel from 110 to 645 px), on the standard's pitch in the pin frame (36.6 px) from 148.6 to 588.2 px
How many slots each forward rail (on the front block's top, and under it) has3CorroboratedPhoto: a photo on file
Photo 3 count used
a photo on file, harvested
Scale: none: a count. Read by three gaps between the front block's teeth along row 640 (1672-1675, 1709-1712, 1746-1749 px) and three under it along row 886; three slots on the top rail close from ahead in 46e53e61437f
Published “13-slot Picatinny rail over the operating handle, plus 3-slot upper and lower forward rails”
Primary Arms, the 16 in AR57 ULT (ULT0116), Features: the 12 in's page doesn't list its rails, a seller, read Oct 18, 2026 the page, harvested Oct 18, 2026
Counted on this upper; the 16 in's listing, the same receiver and rails, says the same.
The rear rail's top above the pin line2.543 in ± 0.02 in 64.6 mmProvisionalWorked out: Read on a copy on file (the tooth tops along row 624, read 2.541 at the first slot and 2.570 at the last (the photo's 0.36 degree lean between the pins, which the rails' tops don't share: the middle), at 367, 624 px) through the camera fitted to it (the header) on the rail's top flat's near edge (0.33 in out): 2.56 in batch 10's pin frame.
Worked out 2.543 in ± 0.02 in used
Read on a copy on file (the tooth tops along row 624, read 2.541 at the first slot and 2.570 at the last (the photo's 0.36 degree lean between the pins, which the rails' tops don't share: the middle), at 367, 624 px) through the camera fitted to it (the header) on the rail's top flat's near edge (0.33 in out): 2.56 in batch 10's pin frame., harvested
The front block's rail top above the pin line2.55 in ± 0.02 in 64.8 mmProvisionalWorked out: Read on a copy on file (the tooth tops at 633 px over 1675 to 1781 px, at 1724, 633 px) through the camera fitted to it (the header) on the rail's top flat's near edge (0.33 in out): 2.548 in batch 10's pin frame.
Worked out 2.55 in ± 0.02 in used
Read on a copy on file (the tooth tops at 633 px over 1675 to 1781 px, at 1724, 633 px) through the camera fitted to it (the header) on the rail's top flat's near edge (0.33 in out): 2.548 in batch 10's pin frame., harvested
The rear rail's rearmost slot's centre ahead of the takedown pin (negative: behind it)-1.216 in ± 0.02 in -30.9 mmProvisionalWorked out: Read on a copy on file (the camera's own fit: the thirteen slots' front edges on the rail's near face (the right ends of the gaps along rows 625 to 627 and 628 to 630, 153.8 to 595.4 px: 36.80 px apart), on MIL-STD-1913's pitch) through the camera fitted to it (the header): -1.15 in batch 10's pin frame.
Worked out -1.216 in ± 0.02 in used
Read on a copy on file (the camera's own fit: the thirteen slots' front edges on the rail's near face (the right ends of the gaps along rows 625 to 627 and 628 to 630, 153.8 to 595.4 px: 36.80 px apart), on MIL-STD-1913's pitch) through the camera fitted to it (the header): -1.15 in batch 10's pin frame., harvested
The rear rail's front end (its front tooth's face)3.979 in ± 0.02 in 101.1 mmProvisionalWorked out: Read on a copy on file (row 626's dark run ends at 628 px, at 628, 628 px) through the camera fitted to it (the header) on the rail's near face (0.4 in out): 4.007 in batch 10's pin frame.
Worked out 3.979 in ± 0.02 in used
Read on a copy on file (row 626's dark run ends at 628 px, at 628, 628 px) through the camera fitted to it (the header) on the rail's near face (0.4 in out): 4.007 in batch 10's pin frame., harvested
The rail block's rear end (the rail overhangs the receiver)-1.767 in ± 0.02 in -44.9 mmProvisionalWorked out: Read on a copy on file (the traced outline's x min, at 94, 662 px, 2.11 above the pin line: the riser's rear end) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at the rail's near face, 0.4 in out, before 2026-10-19: -1.715): -1.731 in batch 10's pin frame. The rail's head above it, on its own near edge, reads -1.72 to -1.74 (the traced outline).
Worked out -1.767 in ± 0.02 in used
Read on a copy on file (the traced outline's x min, at 94, 662 px, 2.11 above the pin line: the riser's rear end) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at the rail's near face, 0.4 in out, before 2026-10-19: -1.715): -1.731 in batch 10's pin frame. The rail's head above it, on its own near edge, reads -1.72 to -1.74 (the traced outline)., harvested
The rail block's rear end as the trace's frame reads it (the outline's map behind the takedown pin: rail_rear_x)-1.767 in ± 0.02 in -44.9 mmConflictWorked out: {.rail_rear_x}
Photo -1.594 in ± 0.02 in
Primary Arms AR57ULT-12_02.jpg, the right side straight on, 2200 x 1467, harvested
Scale: its lug holes' near rims (takedown 243.5, 860.8; pivot 845.0, 864.5 px) as std.ar15.pin_spacing: 94.36 px/in. Read by the traced outline's x min
0.12 behind the camera's reading (rail_rear_x, -1.715; the 16 in's camera reads the same receiver's -1.725): the lens 23 in off reads a two-pin frame's scale differently at the rail's depth and across the part. The model scaled the outline behind the takedown pin by the two until 2026-10-19 (night), when the outline came to be read through the camera.
Worked out -1.767 in used
{.rail_rear_x}, harvested
The trace reads the photo through its camera; the near rims' frame's reading (pinframe) is kept as it was read.
pinframe and camera differ by 0.173 in beyond what each states it is good to.
The rear rail block's front face, flush with its rail's front end (the magazine's latch stands out of it)3.98 in ± 0.02 in 101.1 mmConflictWorked out: Read on a copy on file through the camera fitted to it (the header; 2026-10-19 (night), a working script): the face's near corner at the riser's side (riser_width / 2 out), where the lit face begins: 628.5 to 630.5 px along rows 634 to 652 (3.97 to 3.99), 628 px along rows 667 to 697 beside the latch (3.975 to 3.996). Above the magazine's top the lit face runs on to 645.5 to 646.6 px along rows 640 to 643, its far corner: a face 0.62 across at 3.97 puts the two corners there within a pixel (one 0.835 across, 3 to 5 px off).
Worked out 4.196 in ± 0.03 in
Read on a copy on file (on a 3x crop the block's face at 645 px, where the magazine's rear end is, at 645, 673 px) through the camera fitted to it (the header) on the riser's or the keel's side (0.4175 in out): 4.193 in batch 10's pin frame., harvested
Worked out 3.98 in ± 0.02 in used
Read on a copy on file through the camera fitted to it (the header; 2026-10-19 (night), a working script): the face's near corner at the riser's side (riser_width / 2 out), where the lit face begins: 628.5 to 630.5 px along rows 634 to 652 (3.97 to 3.99), 628 px along rows 667 to 697 beside the latch (3.975 to 3.996). Above the magazine's top the lit face runs on to 645.5 to 646.6 px along rows 640 to 643, its far corner: a face 0.62 across at 3.97 puts the two corners there within a pixel (one 0.835 across, 3 to 5 px off)., harvested
The face where it stands, read at its own edge's depth; the photo reading is the magazine's outline. The 16 in's photo, through its own camera, has 3.97.
photo and camera differ by 0.216 in beyond what each states it is good to.
2026-10-19 (night): the magazine's round end doesn't bear on this face. Through each upper's own camera the face stands 0.10 in behind the magazine's rearmost point (this upper's photo: 3.98 against 4.082; the 16 in's: 3.97 against 4.070), white between the two above and below the latch (latch_bottom_y, latch_top_y), which stands out of the face into the notch in the magazine's round end (fn-p90-50-magazine's own side photo, 76c0d7572a37, has the notch). The face is flush with the rail's front end (rail_front_x, 3.979). Batch 10's reading (photo) is the magazine's outline, where the trace took the magazine out: kept as read.
The front block's top rail: its rearmost slot's centre15.187 in ± 0.03 in 385.7 mmProvisionalWorked out: Read on a copy on file (the camera's own fit: the front rail's near edges (the left ends of its gaps along rows 637 to 640: 1670.1, 1707.5, 1744.3 px) and far edges (their right ends), on MIL-STD-1913's pitch) through the camera fitted to it (the header): 15.253 in batch 10's pin frame.
Worked out 15.187 in ± 0.03 in used
Read on a copy on file (the camera's own fit: the front rail's near edges (the left ends of its gaps along rows 637 to 640: 1670.1, 1707.5, 1744.3 px) and far edges (their right ends), on MIL-STD-1913's pitch) through the camera fitted to it (the header): 15.253 in batch 10's pin frame., harvested
The front block's top rail: its front end16.247 in ± 0.03 in 412.7 mmProvisionalWorked out: Read on a copy on file (its foremost tooth's face along row 640, 1781 px, at 1781, 650 px) through the camera fitted to it (the header) on the rail's near face (0.4 in out): 16.409 in batch 10's pin frame.
Worked out 16.247 in ± 0.03 in used
Read on a copy on file (its foremost tooth's face along row 640, 1781 px, at 1781, 650 px) through the camera fitted to it (the header) on the rail's near face (0.4 in out): 16.409 in batch 10's pin frame., harvested
The front block's lower rail: its rearmost slot's centre15.279 in ± 0.04 in 388.1 mmProvisionalWorked out: Read on a copy on file (the gap's middle (1687 px, row 886) on the rail's near face, moved forward by what the same reading does on the front block's top rail (its gap's middle 15.113 through the camera against its near edges' 15.187)) through the camera fitted to it (the header): 15.414 in batch 10's pin frame.
Worked out 15.279 in ± 0.04 in used
Read on a copy on file (the gap's middle (1687 px, row 886) on the rail's near face, moved forward by what the same reading does on the front block's top rail (its gap's middle 15.113 through the camera against its near edges' 15.187)) through the camera fitted to it (the header): 15.414 in batch 10's pin frame., harvested
The lower forward rail's face (its tooth tops, facing down) above the pin line-0.093 in ± 0.01 in -2.4 mmConflictWorked out: {panzer-ar57-ult-16-upper.lower_rail_bottom_y}
Worked out -0.153 in ± 0.02 in
Read on a copy on file (the lowest dark row under the front block, 886 px, at 1723, 886 px) through the camera fitted to it (the header) on the rail's top flat's near edge (0.33 in out): -0.174 in batch 10's pin frame., harvested
Worked out -0.08 in ± 0.02 in
The same pixel (1723, 886) through the camera on the far edge of the rail's flat (0 - 0.328 out): its face seen from below (2026-10-20)., harvested
Worked out -0.093 in ± 0.01 in used
{panzer-ar57-ult-16-upper.lower_rail_bottom_y}, harvested
This photo's two readings bracket it (-0.150 as the near edge, -0.080 as the far one, the silhouette from below); the 16 in's, from above, reads the edge its silhouette is.
photo and far-edge differ by 0.073 in beyond what each states it is good to.
photo and sixteen differ by 0.06 in beyond what each states it is good to.
The receiver's rear face behind the takedown pin (negative)-0.621 in ± 0.005 in -15.8 mmConfirmedWorked out: {std.ar15.upper_rear_face_x}
Worked out -0.621 in ± 0.005 in used
{std.ar15.upper_rear_face_x}, harvested
The standard's: an upper that fits a mil-spec lower stops ahead of its buffer tower.
The receiver's top at its rear, under the rail block's overhang, above the pin line1.524 in ± 0.03 in 38.7 mmProvisionalWorked out: Read on a copy on file (profiles.side as traced: where its rear face turns back under the rail block's ramp, x -0.70 to -0.77, y 1.576 to 1.613, about 186, 713 px) through the camera fitted to it (the header) on the receiver's side set in above its chamfer (0.51 in out): 1.59 in batch 10's pin frame.
Worked out 1.524 in ± 0.03 in used
Read on a copy on file (profiles.side as traced: where its rear face turns back under the rail block's ramp, x -0.70 to -0.77, y 1.576 to 1.613, about 186, 713 px) through the camera fitted to it (the header) on the receiver's side set in above its chamfer (0.51 in out): 1.59 in batch 10's pin frame., harvested
The receiver's underside above the pin line (it sits on the lower's deck)0.248 in ± 0.0015 in 6.3 mmConflictWorked out: {std.ar15.deck_y}
Worked out 0.2485 in ± 0.0015 in used
{std.ar15.deck_y}, harvested
Worked out 0.156 in ± 0.012 in
Read on a copy on file (the traced outline's lower edge over x 2 to 5, about 842 px) through the camera fitted to it (the header) on the side face (0.72 in out): 0.222 in batch 10's pin frame., harvested
0.09 under the deck: the receiver's near lower edge, from a lens 23 in off and 2.6 in under the pin line, read at the side face's depth (the deck is under the receiver's middle); the standard's is adopted
The seat is the lower's deck; the photo's reading is the near edge's.
std and photo differ by 0.092 in beyond what each states it is good to.
The handguard's top (the magazine lies on it) above the pin line1.635 in ± 0.02 in 41.5 mmProvisionalWorked out: {.mag_underside_y}
Worked out 1.619 in ± 0.02 in
Read on a copy on file (the outline's top under the magazine (the trace's cut, 712.7 px at u 1092) at the riser's width) through the camera fitted to it (the header): 1.65 in batch 10's pin frame., harvested
Worked out 1.635 in ± 0.02 in used
{.mag_underside_y}, harvested
The magazine lies on it: one plane for both (a seat drawn bearing). The model clamps the traced outline's run under the magazine to it (the trace, cut along the magazine's underside on a slightly tilted photo, gives 1.638 at the rear to 1.665 at the front).
The seat is the magazine's underside, read along its length on a 3x crop; the outline's top there is the cut the trace was made with. (Detail pass, 2026-10-18: batch 10 drew the magazine 0.016 to 0.028 in over the handguard's top.)
The handguard's top at its lowest, where it ramps down ahead of the magazine's underside to the front block1.362 in ± 0.02 in 34.6 mmProvisionalWorked out: Read on a copy on file (the lower edge of the light seen under the magazine's front end, 741 px at 1637 px, at 1612, 741 px) through the camera fitted to it (the header) on the top flat's edge (top_flat_width / 2, 0.4175 in out): 1.382 in batch 10's pin frame.
Worked out 1.362 in ± 0.02 in used
Read on a copy on file (the lower edge of the light seen under the magazine's front end, 741 px at 1637 px, at 1612, 741 px) through the camera fitted to it (the header) on the top flat's edge (top_flat_width / 2, 0.4175 in out): 1.382 in batch 10's pin frame., harvested
Where the handguard's top begins its ramp down to the front block13.551 in ± 0.05 in 344.2 mmProvisionalWorked out: Read on a copy on file (where the light under the magazine's front end begins, 1527 px, at 1527, 720 px) through the camera fitted to it (the header) on the top flat's edge (top_flat_width / 2, 0.4175 in out): 13.68 in batch 10's pin frame.
Worked out 13.551 in ± 0.05 in used
Read on a copy on file (where the light under the magazine's front end begins, 1527 px, at 1527, 720 px) through the camera fitted to it (the header) on the top flat's edge (top_flat_width / 2, 0.4175 in out): 13.68 in batch 10's pin frame., harvested
The front block's rear face (the magazine's front cap stands against it)14.866 in ± 0.04 in 377.6 mmProvisionalWorked out: Read on a copy on file (the cap's front edge, behind which the block's rear tooth begins, 1650 px, at 1650, 649 px) through the camera fitted to it (the header) on the rail's near face (0.4 in out): 15.004 in batch 10's pin frame.
Worked out 14.866 in ± 0.04 in used
Read on a copy on file (the cap's front edge, behind which the block's rear tooth begins, 1650 px, at 1650, 649 px) through the camera fitted to it (the header) on the rail's near face (0.4 in out): 15.004 in batch 10's pin frame., harvested
The takedown lug's front face ahead of the takedown pin (the lug under the receiver, at the lower's rear slot)0.22 in ± 0.01 in 5.6 mmProvisionalWorked out: Read on a copy on file through the camera fitted to it (the header; 2026-10-20): the lug's front face, turned toward the lens (over x 11.4), shows as a band between its near edge (264.5 px, on the lug's near side: 0.216 to 0.225 along rows 850 to 860) and its far edge, the silhouette (286.6 px, on its far side: 0.216 to 0.226). Its rear face, the near edge, reads -0.22 (the outline): the lug 0.44 long, centred on its pin. The traced outline, read on the lug's near side, has its front at 0.46. The 16 in's photo through its own camera reads its front face's two edges 0.219 to 0.223.
Worked out 0.22 in ± 0.01 in used
Read on a copy on file through the camera fitted to it (the header; 2026-10-20): the lug's front face, turned toward the lens (over x 11.4), shows as a band between its near edge (264.5 px, on the lug's near side: 0.216 to 0.225 along rows 850 to 860) and its far edge, the silhouette (286.6 px, on its far side: 0.216 to 0.226). Its rear face, the near edge, reads -0.22 (the outline): the lug 0.44 long, centred on its pin. The traced outline, read on the lug's near side, has its front at 0.46. The 16 in's photo through its own camera reads its front face's two edges 0.219 to 0.223., harvested
Both edges of the face agree, and the other upper's photo through its own camera reads the same; the model's lug is cut to it, the outline's front being the face's far edge read as its near one.
The handguard's underside above the pin line0.098 in ± 0.01 in 2.5 mmConflictWorked out: {panzer-ar57-ult-16-upper.handguard_bottom_y}
Worked out 0.058 in ± 0.015 in
Read on a copy on file (the traced outline's lower edge over x 8 to 13.5 (0.049 to 0.062), at 1249, 862 px) through the camera fitted to it (the header) on the keel's side (keel_width / 2, 0.335 in out; at 0.4175, assumed until 2026-10-19: 0.048): 0.056 in batch 10's pin frame., harvested
Worked out 0.135 in ± 0.015 in
The same pixel (1249, 862) through the camera on the keel's far side (0 - keel_width / 2): an underside seen from below, as from this lens 2.6 in under the pin line, shows its far edge (2026-10-20)., harvested
Worked out 0.098 in ± 0.01 in used
{panzer-ar57-ult-16-upper.handguard_bottom_y}, harvested
This photo's two readings bracket it (the near edge 0.058, the far edge, the silhouette from below, 0.135); the 16 in's photo, from above, sees the edge its silhouette is, and from a lens twice as far. An underside seen from below shows its far edge, a face turned toward the lens its far edge, and a lens above a part sees an underside's near edge (2026-10-20: the 12 in's close photo, 2.6 in under the pin line, read both ways brackets this one's).
photo and far-edge differ by 0.077 in beyond what each states it is good to.
photo and sixteen differ by 0.04 in beyond what each states it is good to.
far-edge and sixteen differ by 0.037 in beyond what each states it is good to.
The handguard's front end (its lip round the barrel, where the brake's jam nut stands)17.202 in ± 0.03 in 436.9 mmProvisionalWorked out: Read on a copy on file (the lip's front face meeting the nut (1877 px) at the keel's depth (0.42 in out), where the outline's map puts its clipped end within 0.035 (handguard_front_x_pinframe); at the side face's depth the same pixel is 17.125) through the camera fitted to it (the header): 17.451 in batch 10's pin frame.
Worked out 17.202 in ± 0.03 in used
Read on a copy on file (the lip's front face meeting the nut (1877 px) at the keel's depth (0.42 in out), where the outline's map puts its clipped end within 0.035 (handguard_front_x_pinframe); at the side face's depth the same pixel is 17.125) through the camera fitted to it (the header): 17.451 in batch 10's pin frame., harvested
The height the model's seam ends at, low on the handguard's side (the lower chamfer's foot as batch 10 read it)0.26 in ± 0.02 in 6.6 mmProvisionalWorked out: Read on a copy on file (the line along the handguard's lower part on a 3x crop, 843 px, at 1249, 843 px) through the camera fitted to it (the header) on the keel's side (keel_width / 2, 0.335 in out; at 0.4175, assumed until 2026-10-19: 0.251): 0.263 in batch 10's pin frame.
Worked out 0.26 in ± 0.02 in used
Read on a copy on file (the line along the handguard's lower part on a 3x crop, 843 px, at 1249, 843 px) through the camera fitted to it (the header) on the keel's side (keel_width / 2, 0.335 in out; at 0.4175, assumed until 2026-10-19: 0.251): 0.263 in batch 10's pin frame., harvested
Batch 10 read this as the side face's foot; the detail pass (2026-10-18) read the section's lines down columns of the photo (lower_chamfer_top_y, keel_top_y): the side face ends higher, at 0.713, and this line is the lower chamfer's foot (keel_top_y reads it 0.243 down six columns). Kept for the seam's lean, which the model draws from it as it was.
The handguard's side face's upper edge, where the chamfer up to its top begins (above the pin line)1.26 in ± 0.015 in 32 mmProvisionalWorked out: Read on a copy on file (luminance down columns 1000, 1120, 1240, 1300, 1420 and 1500 px (each the median of five): under the magazine's underside (712 px at 1240) a dark band, the chamfer facing up into the magazine's black underside, to 740.5 to 744.5 px across those columns, where the side face's grey (63) begins: 1.335 to 1.345, at 1240, 743 px) through the camera fitted to it (the header) on the side face (0.72 in out): 1.339 in batch 10's pin frame.
Worked out 1.26 in ± 0.015 in used
Read on a copy on file (luminance down columns 1000, 1120, 1240, 1300, 1420 and 1500 px (each the median of five): under the magazine's underside (712 px at 1240) a dark band, the chamfer facing up into the magazine's black underside, to 740.5 to 744.5 px across those columns, where the side face's grey (63) begins: 1.335 to 1.345, at 1240, 743 px) through the camera fitted to it (the header) on the side face (0.72 in out): 1.339 in batch 10's pin frame., harvested
The section as the 16 in upper's ledger says (side_face_top_y there): a top flat, a chamfer down each side to a flat side face, a chamfer under it, and a keel; this one's own lines read on its own photo, its front ring seen from ahead and to the right in 46e53e61437f.
The receiver's chamfer along its upper sides, under the rail block: its upper edge, where the receiver's side rises set in to the riser's foot (above the pin line)1.506 in ± 0.012 in 38.3 mmProvisionalWorked out: Read on a copy on file (luminance down columns 282, 347 and 440 px (x 0.3, 1.0, 2.0): the face's grey (70 to 72) above, the band's (49 to 59) from 715.5 to 716 px down to 736.5 to 737.5 px, where the side face's (65 to 71) begins again: its top 1.565 to 1.571, its foot 1.337 to 1.342 (side_face_top_y's line on the handguard reads 1.339: one line), at 348, 716 px) through the camera fitted to it (the header) on the receiver's side set in above its chamfer (0.51 in out): 1.569 in batch 10's pin frame.
Worked out 1.506 in ± 0.012 in used
Read on a copy on file (luminance down columns 282, 347 and 440 px (x 0.3, 1.0, 2.0): the face's grey (70 to 72) above, the band's (49 to 59) from 715.5 to 716 px down to 736.5 to 737.5 px, where the side face's (65 to 71) begins again: its top 1.565 to 1.571, its foot 1.337 to 1.342 (side_face_top_y's line on the handguard reads 1.339: one line), at 348, 716 px) through the camera fitted to it (the header) on the receiver's side set in above its chamfer (0.51 in out): 1.569 in batch 10's pin frame., harvested
Detail pass, 2026-10-18: a band along the receiver's upper side from its rear face to a ramp under the rail block's window (receiver_chamfer_front_*), dark in the straight view as the handguard's chamfer is, lit from above in 0bde48a31171 and fe9d442f7b56 (a face turned up). Drawn as the handguard's chamfer's plane carried back to this height, the side above it set in to the deck at the riser's foot.
That chamfer's front end, where it meets the face ahead of it, at receiver_chamfer_front_top_y (ahead of the takedown pin)3.69 in ± 0.02 in 93.7 mmProvisionalWorked out: Read on a copy on file (along row 724 px: the band's dark (12 to 21) ends at 587.5 px, the face's grey (64 to 70) begins, at 588, 724 px) through the camera fitted to it (the header) on the receiver's chamfer (0.6 in out): 3.587 in batch 10's pin frame.
Worked out 3.69 in ± 0.02 in used
Read on a copy on file (along row 724 px: the band's dark (12 to 21) ends at 587.5 px, the face's grey (64 to 70) begins, at 588, 724 px) through the camera fitted to it (the header) on the receiver's chamfer (0.6 in out): 3.587 in batch 10's pin frame., harvested
The height receiver_chamfer_front_top_x is read at1.42 in ± 0.006 in 36.1 mmProvisionalWorked out: Read on a copy on file (row 724 px at that column, at 588, 724 px) through the camera fitted to it (the header) on the receiver's chamfer (0.6 in out): 1.494 in batch 10's pin frame.
Worked out 1.42 in ± 0.006 in used
Read on a copy on file (row 724 px at that column, at 588, 724 px) through the camera fitted to it (the header) on the receiver's chamfer (0.6 in out): 1.494 in batch 10's pin frame., harvested
That chamfer's front end lower down, at receiver_chamfer_front_low_y (ahead of the takedown pin): the end is a ramp3.557 in ± 0.02 in 90.3 mmProvisionalWorked out: Read on a copy on file (along row 736 px: the band ends at 571.5 px; row 730 between (580 px, x 3.507 at 1.429) on the same line: the band's front end leans back going down, a ramp, at 572, 736 px) through the camera fitted to it (the header) on the receiver's chamfer (0.68 in out): 3.415 in batch 10's pin frame.
Worked out 3.557 in ± 0.02 in used
Read on a copy on file (along row 736 px: the band ends at 571.5 px; row 730 between (580 px, x 3.507 at 1.429) on the same line: the band's front end leans back going down, a ramp, at 572, 736 px) through the camera fitted to it (the header) on the receiver's chamfer (0.68 in out): 3.415 in batch 10's pin frame., harvested
The height receiver_chamfer_front_low_x is read at1.278 in ± 0.006 in 32.5 mmProvisionalWorked out: Read on a copy on file (row 736 px at that column, at 572, 736 px) through the camera fitted to it (the header) on the receiver's chamfer (0.68 in out): 1.364 in batch 10's pin frame.
Worked out 1.278 in ± 0.006 in used
Read on a copy on file (row 736 px at that column, at 572, 736 px) through the camera fitted to it (the header) on the receiver's chamfer (0.68 in out): 1.364 in batch 10's pin frame., harvested
The handguard's side face's lower edge, where the chamfer under it begins (above the pin line)0.649 in ± 0.02 in 16.5 mmProvisionalWorked out: Read on a copy on file (luminance down the same six columns: the side face's grey (58) drops to the chamfer's (32) at 798.5 to 803.5 px: 0.704 to 0.721, the lower row of M-LOK slots in the darker face below (see-through at 819 to 828 px at 1240), at 1240, 801 px) through the camera fitted to it (the header) on the side face (0.72 in out): 0.713 in batch 10's pin frame.
Worked out 0.649 in ± 0.02 in used
Read on a copy on file (luminance down the same six columns: the side face's grey (58) drops to the chamfer's (32) at 798.5 to 803.5 px: 0.704 to 0.721, the lower row of M-LOK slots in the darker face below (see-through at 819 to 828 px at 1240), at 1240, 801 px) through the camera fitted to it (the header) on the side face (0.72 in out): 0.713 in batch 10's pin frame., harvested
The lower chamfer's foot, where a short flat side (the keel, the lower block's width) runs down to the underside (above the pin line)0.241 in ± 0.015 in 6.1 mmProvisionalWorked out: Read on a copy on file (luminance down the same six columns: the chamfer's 32 rises to the keel's 53 at 842.5 to 846.5 px (844.5 at 1240 px)) through the camera fitted to it (the header) on the keel's side (keel_width / 2, 0.335 in out; at 0.4175, assumed until 2026-10-19: 0.231): 0.243 in batch 10's pin frame.
Worked out 0.241 in ± 0.015 in used
Read on a copy on file (luminance down the same six columns: the chamfer's 32 rises to the keel's 53 at 842.5 to 846.5 px (844.5 at 1240 px)) through the camera fitted to it (the header) on the keel's side (keel_width / 2, 0.335 in out; at 0.4175, assumed until 2026-10-19: 0.231): 0.243 in batch 10's pin frame., harvested
How far the lower chamfer runs in, across, from the side face to the keel0.385 in ± 0.05 in 9.8 mmProvisionalWorked out: {.handguard_width} / 2 - {.keel_width} / 2
Worked out 0.385 in ± 0.05 in used
{.handguard_width} / 2 - {.keel_width} / 2, harvested
The keel's width read (keel_width), 2026-10-19 (night); it had been taken to be the riser's.
How far the lower chamfer drops, from the side face's foot to the keel0.408 in ± 0.03 in 10.4 mmProvisionalWorked out: {.lower_chamfer_top_y} - {.keel_top_y}
Worked out 0.408 in ± 0.03 in used
{.lower_chamfer_top_y} - {.keel_top_y}, harvested
The lower chamfers' faces: where their normal points, about +x from the top (90 is the right side)133.3° ± 4°ProvisionalWorked out: 90 degrees + atan(lower_chamfer_run / lower_chamfer_drop) = 90 + atan(0.385 / 0.408): the chamfer's normal, from the read heights, the read width and the read keel; the ± is the run's.
Worked out 133.34 deg ± 4 deg used
90 degrees + atan(lower_chamfer_run / lower_chamfer_drop) = 90 + atan(0.385 / 0.408): the chamfer's normal, from the read heights, the read width and the read keel; the ± is the run's., harvested
The expressions have no arctangent: the value is written as worked out, 90 + atan(lower_chamfer_run / lower_chamfer_drop), and the part's test holds it to its inputs.
The lower row's slots' centres on the lower chamfer: how far out of the centre plane0.571 in ± 0.04 in 14.5 mmProvisionalWorked out: {.handguard_width} / 2 - ({.lower_chamfer_top_y} - {.mlok_lower_y}) * {.lower_chamfer_run} / {.lower_chamfer_drop}
Worked out 0.5709 in ± 0.04 in used
{.handguard_width} / 2 - ({.lower_chamfer_top_y} - {.mlok_lower_y}) * {.lower_chamfer_run} / {.lower_chamfer_drop}, harvested
The lower row's anchor: on the centre plane where the line square to the lower chamfer through a slot's centre meets it (above the pin line)1.03 in ± 0.06 in 26.2 mmProvisionalWorked out: {.mlok_lower_y} + {.mlok_lower_z} * {.lower_chamfer_run} / {.lower_chamfer_drop}
Worked out 1.0297 in ± 0.06 in used
{.mlok_lower_y} + {.mlok_lower_z} * {.lower_chamfer_run} / {.lower_chamfer_drop}, harvested
The lower chamfer's surface from the lower row's anchor, along its normal0.785 in ± 0.06 in 19.9 mmProvisionalWorked out: {.mlok_lower_z} * sqrt(1 + ({.lower_chamfer_run} / {.lower_chamfer_drop}) * ({.lower_chamfer_run} / {.lower_chamfer_drop}))
Worked out 0.785 in ± 0.06 in used
{.mlok_lower_z} * sqrt(1 + ({.lower_chamfer_run} / {.lower_chamfer_drop}) * ({.lower_chamfer_run} / {.lower_chamfer_drop})), harvested
The handguard's rear edge on the receiver's side (the seam), at its middle6.915 in ± 0.05 in 175.6 mmProvisionalWorked out: Read on a copy on file (on a 3x crop the edge runs from 860 px under the magazine to 920 px at the side face's foot: the middle, at 890, 775 px) through the camera fitted to it (the header) on the side face (0.72 in out): 6.84 in batch 10's pin frame.
Worked out 6.915 in ± 0.05 in used
Read on a copy on file (on a 3x crop the edge runs from 860 px under the magazine to 920 px at the side face's foot: the middle, at 890, 775 px) through the camera fitted to it (the header) on the side face (0.72 in out): 6.84 in batch 10's pin frame., harvested
The seam at the handguard's top6.589 in ± 0.04 in 167.4 mmProvisionalWorked out: Read on a copy on file (its upper end, 860 px at 727 px, at 861, 732 px) through the camera fitted to it (the header) on the side face (0.72 in out): 6.52 in batch 10's pin frame.
Worked out 6.589 in ± 0.04 in used
Read on a copy on file (its upper end, 860 px at 727 px, at 861, 732 px) through the camera fitted to it (the header) on the side face (0.72 in out): 6.52 in batch 10's pin frame., harvested
The seam at the side face's foot7.246 in ± 0.04 in 184 mmProvisionalWorked out: Read on a copy on file (its lower end, 920 px at 830 px, at 920, 836 px) through the camera fitted to it (the header) on the side face (0.72 in out): 7.16 in batch 10's pin frame.
Worked out 7.246 in ± 0.04 in used
Read on a copy on file (its lower end, 920 px at 830 px, at 920, 836 px) through the camera fitted to it (the header) on the side face (0.72 in out): 7.16 in batch 10's pin frame., harvested
The front block's rear face at the magazine's body's height, where the cap's body stands against it (ahead of the takedown pin); the rail's rear tooth reaches further back over the magazine's top (front_block_rear_x)14.951 in ± 0.05 in 379.8 mmProvisionalWorked out: {.mag_rear_x} + {fn-p90-50-magazine.length}
Worked out 14.96 in ± 0.04 in
Read on a copy on file (along rows 650 to 690 the cap's grey ends at 1668.5 to 1670 px: the cap's front edge on its near side (fn-p90-50-magazine.cap_width / 2 out), where it stands against the block; from behind the block (the lens's foot is at x 11) the cap's near side covers the riser's) through the camera fitted to it (the header): 15.205 in batch 10's pin frame., harvested
Worked out 14.951 in ± 0.05 in used
{.mag_rear_x} + {fn-p90-50-magazine.length}, harvested
Where the magazine's cap stands, its rear end on the latch: the face drawn bearing on it (a seat is drawn bearing).
The magazine (fn-p90-50-magazine.length, its two ends through both uppers' cameras) stands with its cap against this face and its round end on the latch: the face is drawn where its cap stands, 0.01 in behind the cap's front edge read through this photo's camera (photo).
Detail pass, 2026-10-18, the magazine's owner's reading checked on the photo: front_block_rear_x (1650 px) is where the cap's lug's dark face begins at the rail's height; at the body's height the cap is lit to 1668.5 to 1670 px and the block dark from there. The room between the blocks is then 11.01 in (the 16 in's photo: 11.09). The photo is a close one (the pocket's note): an edge nearer the lens than the middle plane reads up to 0.1 in forward here; not corrected, the edge's depth not being known.
Bore axis above the takedown pin centre0.951 in ± 0.025 in 24.2 mmProvisionalWorked out: Read on a copy on file (the middle of the brake's silhouette (758 to 818 px) in columns 2030 to 2050) through the camera fitted to it (the header) on the bore's vertical plane (0.0 in out): 0.893 in batch 10's pin frame.
Worked out 0.951 in ± 0.025 in used
Read on a copy on file (the middle of the brake's silhouette (758 to 818 px) in columns 2030 to 2050) through the camera fitted to it (the header) on the bore's vertical plane (0.0 in out): 0.893 in batch 10's pin frame., harvested
0.006 under the 16 in photo's reading on its barrel (0.957): batch 10's 0.893 in the pin frame of the holes' see-through middles was 0.064 under it
The brake's diameter0.625 in ± 0.025 in 15.9 mmProvisionalWorked out: Read on a copy on file (58 px (760 to 818) in column 2040) through the camera fitted to it (the header): 0.624 in batch 10's pin frame.
Worked out 0.625 in ± 0.025 in used
Read on a copy on file (58 px (760 to 818) in column 2040) through the camera fitted to it (the header): 0.624 in batch 10's pin frame., harvested
The brake's hex jam nut: its rear face (against the handguard's lip)17.221 in ± 0.03 in 437.4 mmProvisionalWorked out: Read on a copy on file (a 3x crop: the nut's rear at 1877 px, at 1877, 787 px) through the camera fitted to it (the header) on the nut's near side (0.36 in out): 17.451 in batch 10's pin frame.
Worked out 17.221 in ± 0.03 in used
Read on a copy on file (a 3x crop: the nut's rear at 1877 px, at 1877, 787 px) through the camera fitted to it (the header) on the nut's near side (0.36 in out): 17.451 in batch 10's pin frame., harvested
The brake's rear face (in front of its jam nut) ahead of the takedown pin17.444 in ± 0.03 in 443.1 mmProvisionalWorked out: Read on a copy on file (a 3x crop: the nut's front and the brake's rear at 1897 px, at 1897, 788 px) through the camera fitted to it (the header) on the brake's near side, or the face the front block's holes are in (0.31 in out): 17.666 in batch 10's pin frame.
Worked out 17.444 in ± 0.03 in used
Read on a copy on file (a 3x crop: the nut's front and the brake's rear at 1897 px, at 1897, 788 px) through the camera fitted to it (the header) on the brake's near side, or the face the front block's holes are in (0.31 in out): 17.666 in batch 10's pin frame., harvested
The jam nut's height as it shows from the side (a hex: across its corners or its flats, as it stands)0.722 in ± 0.04 in 18.3 mmProvisionalWorked out: Read on a copy on file (a 3x crop: 753 to 820 px) through the camera fitted to it (the header): 0.72 in batch 10's pin frame.
Worked out 0.722 in ± 0.04 in used
Read on a copy on file (a 3x crop: 753 to 820 px) through the camera fitted to it (the header): 0.72 in batch 10's pin frame., harvested
The brake's rear band: its front end, where a groove parts it from the ported body17.926 in ± 0.03 in 455.3 mmProvisionalWorked out: Read on a copy on file (a 3x crop: the groove at 1943 px, at 1943, 788 px) through the camera fitted to it (the header) on the brake's near side, or the face the front block's holes are in (0.31 in out): 18.161 in batch 10's pin frame.
Worked out 17.926 in ± 0.03 in used
Read on a copy on file (a 3x crop: the groove at 1943 px, at 1943, 788 px) through the camera fitted to it (the header) on the brake's near side, or the face the front block's holes are in (0.31 in out): 18.161 in batch 10's pin frame., harvested
The brake's rearmost column of ports: its centre18.319 in ± 0.03 in 465.3 mmProvisionalWorked out: Read on a copy on file (a 3x crop: the columns at 1980, 2005 and 2030 px, at 1980, 788 px) through the camera fitted to it (the header) on the ports' near side (0.29 in out): 18.559 in batch 10's pin frame.
Worked out 18.319 in ± 0.03 in used
Read on a copy on file (a 3x crop: the columns at 1980, 2005 and 2030 px, at 1980, 788 px) through the camera fitted to it (the header) on the ports' near side (0.29 in out): 18.559 in batch 10's pin frame., harvested
The ports' columns, centre to centre0.262 in ± 0.01 in 6.7 mmProvisionalWorked out: Read on a copy on file (25 px apart) through the camera fitted to it (the header): 0.269 in batch 10's pin frame.
Worked out 0.262 in ± 0.01 in used
Read on a copy on file (25 px apart) through the camera fitted to it (the header): 0.269 in batch 10's pin frame., harvested
A port's diameter0.156 in ± 0.02 in 4 mmProvisionalWorked out: Read on a copy on file (about 15 px across on a 3x crop) through the camera fitted to it (the header): 0.16 in batch 10's pin frame.
Worked out 0.156 in ± 0.02 in used
Read on a copy on file (about 15 px across on a 3x crop) through the camera fitted to it (the header): 0.16 in batch 10's pin frame., harvested
How many columns of ports along the brake3ProvisionalPhoto: a photo on file
Photo 3 count used
a photo on file, harvested
Scale: none: a count. Read by three along each row (c261b4c5a32d) and from ahead (46e53e61437f)
How many ports round the brake in each column6ProvisionalPhoto: a photo on file
Photo 6 count used
a photo on file, harvested
Scale: none: a count. Read by two rows on the half facing the lens, at 770 and 798 px about the brake's axis at 788 px (radius 29 px): 37 degrees above the right side's middle and 19.5 below, 56.5 apart: six round, one every 60 degrees; the far half inferred
Where the ports are clocked: degrees from the left side's middle toward the top, a row every 6020ProvisionalPhoto: a photo on file
Photo 19.5 count used
a photo on file, harvested
Scale: none: an angle on the brake's own radius. Read by the row 19.5 degrees under the right side's middle (asin(10 / 29)) is 199.5 degrees from the left side's: 19.5 modulo 60
Degrees, held as a count.
The slot across the brake's front end: how deep it runs back from the front0.477 in ± 0.03 in 12.1 mmProvisionalWorked out: Read on a copy on file (light through the front end along row 790 from 2056 px to the front, 2101 px) through the camera fitted to it (the header): 0.484 in batch 10's pin frame.
Worked out 0.477 in ± 0.03 in used
Read on a copy on file (light through the front end along row 790 from 2056 px to the front, 2101 px) through the camera fitted to it (the header): 0.484 in batch 10's pin frame., harvested
The slot's height (it runs across, side to side)0.204 in ± 0.02 in 5.2 mmProvisionalWorked out: Read on a copy on file (19 px (780 to 799) in column 2060) through the camera fitted to it (the header): 0.204 in batch 10's pin frame.
Worked out 0.204 in ± 0.02 in used
Read on a copy on file (19 px (780 to 799) in column 2060) through the camera fitted to it (the header): 0.204 in batch 10's pin frame., harvested
M-LOK slots in the upper row on each side6ProvisionalPhoto: a photo on file
Photo 6 count used
a photo on file, harvested
Scale: none: a count. Read by six dark slots along row 773 (centres 1038, 1190, 1342, 1494, 1646 and 1778 px)
M-LOK slots in the lower row on each side5ProvisionalPhoto: a photo on file
Photo 5 count used
a photo on file, harvested
Scale: none: a count. Read by five see-through slots along row 827 (centres 1113, 1258.5, 1404, 1551, 1697.5 px)
The upper row's foremost slot's centre ahead of the takedown pin16.328 in ± 0.05 in 414.7 mmProvisionalWorked out: Read on a copy on file (the camera's own fit: the upper row's five whole slots (their dark runs' middles along rows 762 to 764 and 769 to 771: 1039.1, 1189.9, 1341.6, 1493.75, 1646.4 px) on Magpul's 40 mm pitch on the side face; the foremost slot, partly under the front block, is one pitch ahead of the last of them) through the camera fitted to it (the header): 16.4 in batch 10's pin frame.
Worked out 16.328 in ± 0.05 in used
Read on a copy on file (the camera's own fit: the upper row's five whole slots (their dark runs' middles along rows 762 to 764 and 769 to 771: 1039.1, 1189.9, 1341.6, 1493.75, 1646.4 px) on Magpul's 40 mm pitch on the side face; the foremost slot, partly under the front block, is one pitch ahead of the last of them) through the camera fitted to it (the header): 16.4 in batch 10's pin frame., harvested
The lower row's foremost slot's centre ahead of the takedown pin15.389 in ± 0.04 in 390.9 mmProvisionalWorked out: Read on a copy on file (the see-through slots' middles along row 827 (1113, 1258.5, 1404, 1551, 1697.5 px) with half the far chamfer's slot's shift toward the lens's foot taken off: the near slots' centres 9.111, 10.677, 12.235, 13.814, 15.389 (1.570 apart on average, Magpul's 1.575)) through the camera fitted to it (the header): 15.523 in batch 10's pin frame.
Worked out 15.389 in ± 0.04 in used
Read on a copy on file (the see-through slots' middles along row 827 (1113, 1258.5, 1404, 1551, 1697.5 px) with half the far chamfer's slot's shift toward the lens's foot taken off: the near slots' centres 9.111, 10.677, 12.235, 13.814, 15.389 (1.570 apart on average, Magpul's 1.575)) through the camera fitted to it (the header): 15.523 in batch 10's pin frame., harvested
The upper row's centre line above the pin line0.984 in ± 0.02 in 25 mmProvisionalWorked out: Read on a copy on file (its slots between 760 and 787 px, at 1649, 772 px) through the camera fitted to it (the header) on the side face (0.72 in out): 1.048 in batch 10's pin frame.
Worked out 0.984 in ± 0.02 in used
Read on a copy on file (its slots between 760 and 787 px, at 1649, 772 px) through the camera fitted to it (the header) on the side face (0.72 in out): 1.048 in batch 10's pin frame., harvested
The lower row's centre line above the pin line0.491 in ± 0.02 in 12.5 mmProvisionalWorked out: Read on a copy on file (the see-through slots' middle row (827 px) with half the far chamfer's slot's vertical shift (13.4 px, toward the lens's foot, below) taken off, on the lower chamfer (0.56 in out)) through the camera fitted to it (the header): 0.462 in batch 10's pin frame.
Worked out 0.491 in ± 0.02 in used
Read on a copy on file (the see-through slots' middle row (827 px) with half the far chamfer's slot's vertical shift (13.4 px, toward the lens's foot, below) taken off, on the lower chamfer (0.56 in out)) through the camera fitted to it (the header): 0.462 in batch 10's pin frame., harvested
The seated magazine's rear end ahead of the takedown pin4.082 in ± 0.02 in 103.7 mmProvisionalWorked out: Read on a copy on file through the camera fitted to it (the header; 2026-10-19 (night), a working script): the round end's outline where it stands against the rail block's lit face, above the latch: 643.6 to 643.8 px along rows 650 to 662, as the half circle in plan it is (fn-p90-50-magazine.width), the line of sight tangent to it 0.26 in nearer the lens than its rearmost point: 4.077 to 4.087.
Worked out 4.101 in ± 0.03 in
Read on a copy on file (its round end's outline at 644.5 px (row 670): the end a half circle in plan as wide as the magazine (fn-p90-50-magazine.width), the line of sight tangent to it a little nearer the lens than its rearmost point) through the camera fitted to it (the header): 4.195 in batch 10's pin frame., harvested
At the latch's height: the latch's lit rim stands beside the magazine's end there.
Worked out 4.082 in ± 0.02 in used
Read on a copy on file through the camera fitted to it (the header; 2026-10-19 (night), a working script): the round end's outline where it stands against the rail block's lit face, above the latch: 643.6 to 643.8 px along rows 650 to 662, as the half circle in plan it is (fn-p90-50-magazine.width), the line of sight tangent to it 0.26 in nearer the lens than its rearmost point: 4.077 to 4.087., harvested
Row 670 (photo) is at the latch's height, where the latch's lit rim stands beside the magazine's end; above it the end stands against the block's lit face. The 16 in's photo, through its own camera, has 4.070 for the same seat.
The magazine's latch, out of the rear rail block's front face into the notch in the magazine's round end: its underside above the pin line1.76 in ± 0.02 in 44.7 mmProvisionalWorked out: Read on a copy on file through the camera fitted to it (the header; 2026-10-19 (night)): the dark lobe between the block's face and the magazine's round end, beside the face's near corner (628 px), from row 666.5 to 697.5: its foot at 1.763 on the face's near corner (riser_width / 2 out). The 16 in's photo has it from 1.78 to 2.12.
Worked out 1.76 in ± 0.02 in used
Read on a copy on file through the camera fitted to it (the header; 2026-10-19 (night)): the dark lobe between the block's face and the magazine's round end, beside the face's near corner (628 px), from row 666.5 to 697.5: its foot at 1.763 on the face's near corner (riser_width / 2 out). The 16 in's photo has it from 1.78 to 2.12., harvested
The magazine's latch: its top above the pin line2.1 in ± 0.02 in 53.3 mmProvisionalWorked out: Read on a copy on file as latch_bottom_y: its top at row 666.5, 2.100.
Worked out 2.1 in ± 0.02 in used
Read on a copy on file as latch_bottom_y: its top at row 666.5, 2.100., harvested
The magazine's latch: across0.62 in ± 0.1 in 15.7 mmProvisionalWorked out: {.riser_width}
Worked out 0.62 in ± 0.1 in used
{.riser_width}, harvested
The seated magazine's underside (its body's flat bottom, lying on the handguard's top) above the pin line1.635 in ± 0.02 in 41.5 mmProvisionalWorked out: Read on a copy on file (the line under the magazine at 711 px (u 1092): from a lens 2.6 in under the pin line the magazine's underside shows as a band down to where the handguard's top edge hides it, so the line is that edge, at the top flat's edge) through the camera fitted to it (the header) (top_flat_width / 2, 0.4175 in out): 1.666 in batch 10's pin frame.
Worked out 1.635 in ± 0.02 in used
Read on a copy on file (the line under the magazine at 711 px (u 1092): from a lens 2.6 in under the pin line the magazine's underside shows as a band down to where the handguard's top edge hides it, so the line is that edge, at the top flat's edge) through the camera fitted to it (the header) (top_flat_width / 2, 0.4175 in out): 1.666 in batch 10's pin frame., harvested
0.035 over the 16 in photo's 1.600 for the same seat (batch 10's pin frame had 0.1 over its 1.572)
The round pocket the magazine's feed tower sits in: its centre ahead of the takedown pin5.056 in ± 0.04 in 128.4 mmConflictWorked out: {.mag_rear_x} + {fn-p90-50-magazine.width} / 2
Worked out 5.162 in ± 0.04 in
Read on a copy on file (the middle of the notch the tower shows through (653 to 793 px: 723 px) on the side face (0.72 in out), the tower's centre being the notch's) through the camera fitted to it (the header): 5.037 in batch 10's pin frame., harvested
Worked out 5.19 in ± 0.05 in
The photo reading moved from the near wall, where the notch's ends are, to the pocket's middle plane, the plane the pins' frame reads true in (detail pass, 2026-10-18). The photo is a close one: on its near side face the upper M-LOK row's five centres read 1.635 apart for the standard's 1.575 (3.8% over), while the lower row's see-through centres, set by the slots of both walls together, read the standard's (1.572): the near face is magnified 1.038 about the lens's axis (a lens about 20 in off, 0.75 in nearer than the middle). About the image's middle (1100 px, 9.10 in ahead of the takedown pin), 9.10 + (5.037 - 9.10) / 1.038 = 5.186. The ± is the magnification's spread and the lens's axis taken at the image's middle (a cropped photo's may not be)., harvested
The magazine's tower is concentric with its round rear end (fn-p90-50-magazine.width / 2 ahead of it): mag_rear_x + 0.97 = 5.165, 0.02 from this; the photo reading as it stood had the tower 0.14 ahead of the pocket.
Worked out 5.056 in ± 0.04 in used
{.mag_rear_x} + {fn-p90-50-magazine.width} / 2, harvested
Where the magazine's tower stands: concentric with its round end (US 4,905,394's FIG. 3 and FIG. 4; the magazine's own side photo has the tower flush with its rear end within a pixel), the round end against the rail block. No view on file shows the pocket from above.
The pocket holds the magazine's tower, so it is drawn round it. The notch the tower shows through in the near wall reads 5.162 through the photo's camera (5.065 in the trace's frame) (photo): a chord whose two ends lie at two depths of a wall seen from a lens off to one side, ahead of the tower's place by 0.09; both are kept, and the magazine's own photo (the tower concentric with the round end) decides it.
photo and tower differ by 0.106 in beyond what each states it is good to.
mid-plane and tower differ by 0.134 in beyond what each states it is good to.
The notch in each wall the magazine's feed tower shows through: its length1.462 in ± 0.05 in 37.1 mmProvisionalWorked out: Read on a copy on file (653 to 793 px on a 3x crop, the wall dark either side) through the camera fitted to it (the header): 1.506 in batch 10's pin frame.
Worked out 1.462 in ± 0.05 in used
Read on a copy on file (653 to 793 px on a 3x crop, the wall dark either side) through the camera fitted to it (the header): 1.506 in batch 10's pin frame., harvested
The pocket's floor (the tower's underside) above the pin line1.063 in ± 0.02 in 27 mmProvisionalWorked out: Read on a copy on file (the tower's lower edge on a 3x crop, 757 px, at 723, 757 px) through the camera fitted to it (the header) on the side face (0.72 in out): 1.149 in batch 10's pin frame.
Worked out 1.063 in ± 0.02 in used
Read on a copy on file (the tower's lower edge on a 3x crop, 757 px, at 723, 757 px) through the camera fitted to it (the header) on the side face (0.72 in out): 1.149 in batch 10's pin frame., harvested
The rail block's window for the handle (the larger, foremost of two): its rear end2.946 in ± 0.02 in 74.8 mmProvisionalWorked out: Read on a copy on file (on a 5x crop 531 px; the lever stands in it from the right, at 531, 680 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 2.986): 2.968 in batch 10's pin frame.
Worked out 2.946 in ± 0.02 in used
Read on a copy on file (on a 5x crop 531 px; the lever stands in it from the right, at 531, 680 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 2.986): 2.968 in batch 10's pin frame., harvested
The handle's window: its front end3.544 in ± 0.02 in 90 mmProvisionalWorked out: Read on a copy on file (on a 5x crop 587 px, at 587, 681 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 3.581): 3.568 in batch 10's pin frame.
Worked out 3.544 in ± 0.02 in used
Read on a copy on file (on a 5x crop 587 px, at 587, 681 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 3.581): 3.568 in batch 10's pin frame., harvested
The second, smaller window behind it: its rear end2.292 in ± 0.02 in 58.2 mmProvisionalWorked out: Read on a copy on file (on a 5x crop 470 px, at 470, 680 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 2.335): 2.312 in batch 10's pin frame.
Worked out 2.292 in ± 0.02 in used
Read on a copy on file (on a 5x crop 470 px, at 470, 680 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 2.335): 2.312 in batch 10's pin frame., harvested
The second window: its front end2.601 in ± 0.02 in 66.1 mmProvisionalWorked out: Read on a copy on file (on a 5x crop 499 px, at 499, 680 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 2.643): 2.622 in batch 10's pin frame.
Worked out 2.601 in ± 0.02 in used
Read on a copy on file (on a 5x crop 499 px, at 499, 680 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 2.643): 2.622 in batch 10's pin frame., harvested
The two windows' bottom edge above the pin line1.758 in ± 0.015 in 44.7 mmProvisionalWorked out: Read on a copy on file (on a 5x crop 697 px, at 534, 697 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 1.737): 1.779 in batch 10's pin frame.
Worked out 1.758 in ± 0.015 in used
Read on a copy on file (on a 5x crop 697 px, at 534, 697 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 1.737): 1.779 in batch 10's pin frame., harvested
The two windows' top edge above the pin line2.131 in ± 0.015 in 54.1 mmProvisionalWorked out: Read on a copy on file (on a 5x crop 663 px, at 534, 663 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 2.109): 2.148 in batch 10's pin frame.
Worked out 2.131 in ± 0.015 in used
Read on a copy on file (on a 5x crop 663 px, at 534, 663 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 2.109): 2.148 in batch 10's pin frame., harvested
The magazine catch's lever where it stands out of the window on the right: its rear face2.9 in ± 0.02 in 73.7 mmProvisionalWorked out: Read on a copy on file (on a 5x crop 513 px, at 513, 668 px) through the camera fitted to it (the header) on the side face (0.72 in out): 2.774 in batch 10's pin frame.
Worked out 2.9 in ± 0.02 in used
Read on a copy on file (on a 5x crop 513 px, at 513, 668 px) through the camera fitted to it (the header) on the side face (0.72 in out): 2.774 in batch 10's pin frame., harvested
The lever's front face3.16 in ± 0.02 in 80.3 mmProvisionalWorked out: Read on a copy on file (on a 5x crop 538 px, at 538, 668 px) through the camera fitted to it (the header) on the side face (0.72 in out): 3.04 in batch 10's pin frame.
Worked out 3.16 in ± 0.02 in used
Read on a copy on file (on a 5x crop 538 px, at 538, 668 px) through the camera fitted to it (the header) on the side face (0.72 in out): 3.04 in batch 10's pin frame., harvested
The lever's lower end above the pin line1.799 in ± 0.02 in 45.7 mmProvisionalWorked out: Read on a copy on file (on a 5x crop 686 px, at 525, 686 px) through the camera fitted to it (the header) on the side face (0.72 in out): 1.899 in batch 10's pin frame.
Worked out 1.799 in ± 0.02 in used
Read on a copy on file (on a 5x crop 686 px, at 525, 686 px) through the camera fitted to it (the header) on the side face (0.72 in out): 1.899 in batch 10's pin frame., harvested
The lever's upper end above the pin line (it stands up over the window's top)2.185 in ± 0.02 in 55.5 mmProvisionalWorked out: Read on a copy on file (on a 5x crop 650 px, at 525, 650 px) through the camera fitted to it (the header) on the side face (0.72 in out): 2.287 in batch 10's pin frame.
Worked out 2.185 in ± 0.02 in used
Read on a copy on file (on a 5x crop 650 px, at 525, 650 px) through the camera fitted to it (the header) on the side face (0.72 in out): 2.287 in batch 10's pin frame., harvested
The row of blind holes along the rail block's side, under its slots: their centres above the pin line2.27 in ± 0.015 in 57.7 mmProvisionalWorked out: Read on a copy on file (on a 5x crop at 650 px, under each slot (438, 474, 511, 548, 585 px: 36.75 apart), at 488, 650 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 2.247): 2.286 in batch 10's pin frame.
Worked out 2.27 in ± 0.015 in used
Read on a copy on file (on a 5x crop at 650 px, under each slot (438, 474, 511, 548, 585 px: 36.75 apart), at 488, 650 px) through the camera fitted to it (the header) on the riser's side (riser_width / 2, 0.31 in out; at 0.4175, assumed until 2026-10-19: 2.247): 2.286 in batch 10's pin frame., harvested
Those holes' diameter0.171 in ± 0.02 in 4.3 mmProvisionalWorked out: Read on a copy on file (16 px across on a 5x crop, on the riser's side) through the camera fitted to it (the header): 0.172 in batch 10's pin frame.
Worked out 0.171 in ± 0.02 in used
Read on a copy on file (16 px across on a 5x crop, on the riser's side) through the camera fitted to it (the header): 0.172 in batch 10's pin frame., harvested
0.125 on the 16 in's photo (10 px at 80 px/in): each its own
The front block's five holes: the rearmost's centre15.139 in ± 0.04 in 384.5 mmProvisionalWorked out: Read on a copy on file (on a 3x crop the five at 1675, 1698, 1723, 1748 and 1773 px, at 1675, 663 px) through the camera fitted to it (the header) on the brake's near side, or the face the front block's holes are in (0.31 in out): 15.27 in batch 10's pin frame.
Worked out 15.139 in ± 0.04 in used
Read on a copy on file (on a 3x crop the five at 1675, 1698, 1723, 1748 and 1773 px, at 1675, 663 px) through the camera fitted to it (the header) on the brake's near side, or the face the front block's holes are in (0.31 in out): 15.27 in batch 10's pin frame., harvested
The front block's holes, centre to centre0.265 in ± 0.015 in 6.7 mmProvisionalWorked out: Read on a copy on file (the five rings' centres 25.0 px apart, 1674.3 to 1774.4 px, 2026-10-19, at the riser's side; 24.5 px by eye before, 0.2597) through the camera fitted to it (the header): 0.2635 in batch 10's pin frame.
Worked out 0.2653 in ± 0.015 in used
Read on a copy on file (the five rings' centres 25.0 px apart, 1674.3 to 1774.4 px, 2026-10-19, at the riser's side; 24.5 px by eye before, 0.2597) through the camera fitted to it (the header): 0.2635 in batch 10's pin frame., harvested
The front block's holes: their centres above the pin line2.23 in ± 0.02 in 56.6 mmProvisionalWorked out: Read on a copy on file (663 px, at 1724, 663 px) through the camera fitted to it (the header) on the brake's near side, or the face the front block's holes are in (0.31 in out): 2.227 in batch 10's pin frame.
Worked out 2.23 in ± 0.02 in used
Read on a copy on file (663 px, at 1724, 663 px) through the camera fitted to it (the header) on the brake's near side, or the face the front block's holes are in (0.31 in out): 2.227 in batch 10's pin frame., harvested
The lower block's five holes: the rearmost's centre15.326 in ± 0.04 in 389.3 mmProvisionalWorked out: Read on a copy on file (on a 3x crop the five at 1697, 1727, 1757, 1787 and 1817 px, at 1697, 857 px) through the camera fitted to it (the header) on the keel's side (keel_width / 2, 0.335 in out; at 0.4175, assumed until 2026-10-19: 15.312): 15.52 in batch 10's pin frame.
Worked out 15.326 in ± 0.04 in used
Read on a copy on file (on a 3x crop the five at 1697, 1727, 1757, 1787 and 1817 px, at 1697, 857 px) through the camera fitted to it (the header) on the keel's side (keel_width / 2, 0.335 in out; at 0.4175, assumed until 2026-10-19: 15.312): 15.52 in batch 10's pin frame., harvested
The lower block's holes, centre to centre0.317 in ± 0.015 in 8.1 mmProvisionalWorked out: Read on a copy on file (the five rings' centres 30.4 px apart, 1695.6 to 1817.3 px, 2026-10-19, at the keel's side; 30 px by eye before, 0.3116) through the camera fitted to it (the header): 0.3225 in batch 10's pin frame.
Worked out 0.3174 in ± 0.015 in used
Read on a copy on file (the five rings' centres 30.4 px apart, 1695.6 to 1817.3 px, 2026-10-19, at the keel's side; 30 px by eye before, 0.3116) through the camera fitted to it (the header): 0.3225 in batch 10's pin frame., harvested
The lower block's holes: their centres above the pin line0.157 in ± 0.02 in 4 mmProvisionalWorked out: Read on a copy on file (857 px, at 1760, 857 px) through the camera fitted to it (the header) on the keel's side (keel_width / 2, 0.335 in out; at 0.4175, assumed until 2026-10-19: 0.147): 0.143 in batch 10's pin frame.
Worked out 0.157 in ± 0.02 in used
Read on a copy on file (857 px, at 1760, 857 px) through the camera fitted to it (the header) on the keel's side (keel_width / 2, 0.335 in out; at 0.4175, assumed until 2026-10-19: 0.147): 0.143 in batch 10's pin frame., harvested
The handguard's width across its side faces (the receiver's too: one figure)1.44 in ± 0.06 in 36.6 mmProvisionalWorked out: {panzer-ar57-ult-16-upper.handguard_width}
Worked out 1.44 in used
{panzer-ar57-ult-16-upper.handguard_width}, harvested
The riser under each rail block's rail head (the face the rows of blind holes are in), across0.62 in ± 0.03 in 15.7 mmConflictWorked out: Read through cameras fitted to two views of this upper from ahead (2026-10-19 (night), a working script, fitW2.py): each blind hole a ray from this upper's straight view's camera (the header; the dark ring's centre there) and its rim's centre in the other view, the depth along the rays one figure a row, left to the fit. 4d5581786e3d (from ahead, right and above, the whole upper; 0.67 px rms): its front rail's six slot edges and its receiver rail's twenty-six on MIL-STD-1913's pitch, the front rail's top flat's near and far edges and its head's widest, and three rows of holes: the front block's row 0.314 ± 0.005 out of the centre plane (0.303 to 0.326 with the rail's lines left out in turn), the rear block's row under its thirteen slots 0.316 ± 0.021. 46e53e61437f (the front block close, handguard_width's camera with the holes' depth left free): 0.310. Under each block's head the riser shows as a strip with the holes in it, the head (0.835) overhanging it; the rear block's face runs on down from the strip with a hairline between, the front block's below a dark band. Checked on the rail block's front face in the straight view (rail_block_front_x): 0.62 across puts its two corners where they show within a pixel, 0.835 3 to 5 px off.
Worked out 0.835 in ± 0.05 in
An assumption for the drawing, not a reading (batch 10 to 2026-10-19): the riser as wide as the rail's head (std.picatinny.top_width), its sides taken to run down from the head with no step in the 16 in's views from behind (fe9d442f7b56, 0bde48a31171)., harvested
Worked out 0.62 in ± 0.03 in used
Read through cameras fitted to two views of this upper from ahead (2026-10-19 (night), a working script, fitW2.py): each blind hole a ray from this upper's straight view's camera (the header; the dark ring's centre there) and its rim's centre in the other view, the depth along the rays one figure a row, left to the fit. 4d5581786e3d (from ahead, right and above, the whole upper; 0.67 px rms): its front rail's six slot edges and its receiver rail's twenty-six on MIL-STD-1913's pitch, the front rail's top flat's near and far edges and its head's widest, and three rows of holes: the front block's row 0.314 ± 0.005 out of the centre plane (0.303 to 0.326 with the rail's lines left out in turn), the rear block's row under its thirteen slots 0.316 ± 0.021. 46e53e61437f (the front block close, handguard_width's camera with the holes' depth left free): 0.310. Under each block's head the riser shows as a strip with the holes in it, the head (0.835) overhanging it; the rear block's face runs on down from the strip with a hairline between, the front block's below a dark band. Checked on the rail block's front face in the straight view (rail_block_front_x): 0.62 across puts its two corners where they show within a pixel, 0.835 3 to 5 px off., harvested
Three rows of holes through two cameras, over an assumption; the head's overhang shows on both blocks in 4d5581786e3d.
assumed and camera differ by 0.215 in beyond what each states it is good to.
The keel under the lower chamfers (the lower block's side, the face its row of blind holes is in), across0.67 in ± 0.03 in 17 mmProvisionalWorked out: Read through the camera fitted to 4d5581786e3d as riser_width is (2026-10-19 (night)): the lower block's row of five blind holes 0.335 ± 0.008 out of the centre plane (0.334 to 0.340 with the rails' lines left out in turn). In the straight view the keel's strip (keel_top_y to the underside) runs from the seam to the lower block with the holes in it, and the lower rail's head (0.835) overhangs it there.
Worked out 0.67 in ± 0.03 in used
Read through the camera fitted to 4d5581786e3d as riser_width is (2026-10-19 (night)): the lower block's row of five blind holes 0.335 ± 0.008 out of the centre plane (0.334 to 0.340 with the rails' lines left out in turn). In the straight view the keel's strip (keel_top_y to the underside) runs from the seam to the lower block with the holes in it, and the lower rail's head (0.835) overhangs it there., harvested
The handguard's top flat under the magazine (between the two upper chamfers), across0.835 in ± 0.1 in 21.2 mmProvisionalWorked out: An assumption for the drawing, not a reading: the flat is under the magazine (1.95 across) in every view on file. Drawn as it was drawn (as wide as the rail's head, std.picatinny.top_width) when it was taken to be the riser's width, until 2026-10-19. The front block's lower face's edge (y 1.54, 0.46 to 0.50 out through 46e53e61437f's and 4d5581786e3d's cameras) and the side face's top (side_face_top_y) put that chamfer's plane, carried up to the tray, 0.74 to 0.85 across.
Worked out 0.835 in ± 0.1 in used
An assumption for the drawing, not a reading: the flat is under the magazine (1.95 across) in every view on file. Drawn as it was drawn (as wide as the rail's head, std.picatinny.top_width) when it was taken to be the riser's width, until 2026-10-19. The front block's lower face's edge (y 1.54, 0.46 to 0.50 out through 46e53e61437f's and 4d5581786e3d's cameras) and the side face's top (side_face_top_y) put that chamfer's plane, carried up to the tray, 0.74 to 0.85 across., harvested
The handguard's wall0.12 in ± 0.04 in 3 mmProvisionalWorked out: {panzer-ar57-ult-16-upper.handguard_wall}
Worked out 0.12 in used
{panzer-ar57-ult-16-upper.handguard_wall}, harvested
Each lug's clearance to the lower's slot it stands in, per side0.005 in ± 0.005 in 0.1 mmProvisionalWorked out: {panzer-ar57-ult-16-upper.lug_clearance}
Worked out 0.005 in used
{panzer-ar57-ult-16-upper.lug_clearance}, harvested
How far the lever stands out of the rail block's right side0.3 in ± 0.1 in 7.6 mmProvisionalWorked out: {panzer-ar57-ult-16-upper.catch_out}
Worked out 0.3 in used
{panzer-ar57-ult-16-upper.catch_out}, harvested
How deep the blind holes go0.1 in ± 0.05 in 2.5 mmProvisionalWorked out: {panzer-ar57-ult-16-upper.cross_hole_depth}
Worked out 0.1 in used
{panzer-ar57-ult-16-upper.cross_hole_depth}, harvested
The bolt's round rear end, as it shows in the receiver's rear face0.75 in ± 0.1 in 19 mmProvisionalWorked out: {panzer-ar57-ult-16-upper.bolt_end_d}
Worked out 0.75 in used
{panzer-ar57-ult-16-upper.bolt_end_d}, harvested
How far the bolt's end stands out of the rear face0.05 in ± 0.03 in 1.3 mmProvisionalWorked out: {panzer-ar57-ult-16-upper.bolt_end_proud}
Worked out 0.05 in used
{panzer-ar57-ult-16-upper.bolt_end_proud}, harvested
The groove between the brake's rear band and its ported body: its width0.03 in ± 0.015 in 0.8 mmProvisionalWorked out: {panzer-ar57-ult-16-upper.brake_groove_w}
Worked out 0.03 in used
{panzer-ar57-ult-16-upper.brake_groove_w}, harvested
That groove's depth0.02 in ± 0.01 in 0.5 mmProvisionalWorked out: {panzer-ar57-ult-16-upper.brake_groove_depth}
Worked out 0.02 in used
{panzer-ar57-ult-16-upper.brake_groove_depth}, harvested
The receiver's width1.44 in ± 0.06 in 36.6 mmProvisionalWorked out: {.handguard_width}
Worked out 1.44 in used
{.handguard_width}, harvested
Drawn as the handguard's, read with it.
The barrel's diameter0.53 in ± 0.025 in 13.5 mmProvisionalWorked out: {panzer-ar57-ult-16-upper.barrel_od}
Worked out 0.53 in used
{panzer-ar57-ult-16-upper.barrel_od}, harvested
The barrel's breech end ahead of the takedown pin (hidden in the receiver)5.508 in ± 0.5 in 139.9 mmProvisionalWorked out: {panzer-ar57-ult-16-upper.barrel_rear_x}
Worked out 5.508 in used
{panzer-ar57-ult-16-upper.barrel_rear_x}, harvested
The bore0.224 in ± 0.003 in 5.7 mmProvisionalWorked out: The cartridge's name: 5.7 mm across (5.7 / 25.4); the bore is drawn as one plain hole at it.
Worked out 0.224 in ± 0.003 in used
The cartridge's name: 5.7 mm across (5.7 / 25.4); the bore is drawn as one plain hole at it., harvested
The brake's bore0.204 in ± 0.03 in 5.2 mmProvisionalWorked out: {.brake_slot_width}
Worked out 0.204 in ± 0.03 in used
{.brake_slot_width}, harvested
The slot across its front opens the bore it runs into: drawn as wide as the slot.
The round pocket in the receiver's top the magazine's feed tower sits in: its diameter1.883 in ± 0.08 in 47.8 mmProvisionalWorked out: {fn-p90-50-magazine.tower_d} + 2 * {.lug_clearance}
Worked out 1.883 in ± 0.08 in used
{fn-p90-50-magazine.tower_d} + 2 * {.lug_clearance}, harvested
What the pocket holds, a clearance round it: the magazine's own figure. No view shows the pocket from above with a scale; the notch it makes in each wall is read (feed_notch_length).
The handguard's bore (round the barrel)0.82 in ± 0.1 in 20.8 mmProvisionalWorked out: {panzer-ar57-ult-16-upper.handguard_id}
Worked out 0.82 in used
{panzer-ar57-ult-16-upper.handguard_id}, harvested
The charging handle's channel along the receiver's right side: its rear end0.774 in ± 0.03 in 19.7 mmProvisionalWorked out: Read on a copy on file (on a 2.5x crop the channel's rear end at 300 px, at 300, 797 px) through the camera fitted to it (the header) on the side face (0.72 in out): 0.495 in batch 10's pin frame.
Worked out 0.774 in ± 0.03 in used
Read on a copy on file (on a 2.5x crop the channel's rear end at 300 px, at 300, 797 px) through the camera fitted to it (the header) on the side face (0.72 in out): 0.495 in batch 10's pin frame., harvested
The channel's front end6.988 in ± 0.03 in 177.5 mmProvisionalWorked out: Read on a copy on file (on a 2.5x crop its front end at 896 px, at 896, 801 px) through the camera fitted to it (the header) on the side face (0.72 in out): 6.905 in batch 10's pin frame.
Worked out 6.988 in ± 0.03 in used
Read on a copy on file (on a 2.5x crop its front end at 896 px, at 896, 801 px) through the camera fitted to it (the header) on the side face (0.72 in out): 6.905 in batch 10's pin frame., harvested
The channel's lower edge above the pin line0.358 in ± 0.02 in 9.1 mmProvisionalWorked out: Read on a copy on file (822 px, at 580, 823 px) through the camera fitted to it (the header) on the side face (0.72 in out): 0.43 in batch 10's pin frame.
Worked out 0.358 in ± 0.02 in used
Read on a copy on file (822 px, at 580, 823 px) through the camera fitted to it (the header) on the side face (0.72 in out): 0.43 in batch 10's pin frame., harvested
The channel's upper edge above the pin line0.865 in ± 0.02 in 22 mmProvisionalWorked out: Read on a copy on file (774 px, at 580, 775 px) through the camera fitted to it (the header) on the side face (0.72 in out): 0.95 in batch 10's pin frame.
Worked out 0.865 in ± 0.02 in used
Read on a copy on file (774 px, at 580, 775 px) through the camera fitted to it (the header) on the side face (0.72 in out): 0.95 in batch 10's pin frame., harvested
The charging handle's tab in the channel: its rear end5.296 in ± 0.03 in 134.5 mmProvisionalWorked out: Read on a copy on file (the raised tab from 728 px, at 729, 797 px) through the camera fitted to it (the header) on the handle's tab (0.92 in out): 5.1 in batch 10's pin frame.
Worked out 5.296 in ± 0.03 in used
Read on a copy on file (the raised tab from 728 px, at 729, 797 px) through the camera fitted to it (the header) on the handle's tab (0.92 in out): 5.1 in batch 10's pin frame., harvested
The handle's tab: its front end6.907 in ± 0.03 in 175.4 mmProvisionalWorked out: Read on a copy on file (to 884 px, at 885, 798 px) through the camera fitted to it (the header) on the handle's tab (0.92 in out): 6.78 in batch 10's pin frame.
Worked out 6.907 in ± 0.03 in used
Read on a copy on file (to 884 px, at 885, 798 px) through the camera fitted to it (the header) on the handle's tab (0.92 in out): 6.78 in batch 10's pin frame., harvested
The handle's tab: its lower edge above the pin line0.433 in ± 0.02 in 11 mmProvisionalWorked out: Read on a copy on file (814 px, at 803, 815 px) through the camera fitted to it (the header) on the handle's tab (0.92 in out): 0.53 in batch 10's pin frame.
Worked out 0.433 in ± 0.02 in used
Read on a copy on file (814 px, at 803, 815 px) through the camera fitted to it (the header) on the handle's tab (0.92 in out): 0.53 in batch 10's pin frame., harvested
The handle's tab: its upper edge above the pin line0.79 in ± 0.02 in 20.1 mmProvisionalWorked out: Read on a copy on file (780 px, at 803, 781 px) through the camera fitted to it (the header) on the handle's tab (0.92 in out): 0.9 in batch 10's pin frame.
Worked out 0.79 in ± 0.02 in used
Read on a copy on file (780 px, at 803, 781 px) through the camera fitted to it (the header) on the handle's tab (0.92 in out): 0.9 in batch 10's pin frame., harvested
The opening in the channel's floor onto the bolt: its rear end3.141 in ± 0.03 in 79.8 mmProvisionalWorked out: Read on a copy on file (the dark opening on a 2.5x crop from 530 px, at 530, 798 px) through the camera fitted to it (the header) on the channel's floor (0.62 in out): 2.97 in batch 10's pin frame.
Worked out 3.141 in ± 0.03 in used
Read on a copy on file (the dark opening on a 2.5x crop from 530 px, at 530, 798 px) through the camera fitted to it (the header) on the channel's floor (0.62 in out): 2.97 in batch 10's pin frame., harvested
That opening's front end3.999 in ± 0.03 in 101.6 mmProvisionalWorked out: Read on a copy on file (to 612 px, at 612, 799 px) through the camera fitted to it (the header) on the channel's floor (0.62 in out): 3.85 in batch 10's pin frame.
Worked out 3.999 in ± 0.03 in used
Read on a copy on file (to 612 px, at 612, 799 px) through the camera fitted to it (the header) on the channel's floor (0.62 in out): 3.85 in batch 10's pin frame., harvested
How deep the channel is cut into the side0.1 in ± 0.05 in 2.5 mmProvisionalWorked out: {panzer-ar57-ult-16-upper.channel_depth}
Worked out 0.1 in used
{panzer-ar57-ult-16-upper.channel_depth}, harvested
The gap round the handle's bar in its channel0.03 in ± 0.015 in 0.8 mmProvisionalWorked out: {panzer-ar57-ult-16-upper.channel_gap}
Worked out 0.03 in used
{panzer-ar57-ult-16-upper.channel_gap}, harvested
How far the handle's tab stands out of the receiver's right side0.2 in ± 0.08 in 5.1 mmProvisionalWorked out: {panzer-ar57-ult-16-upper.handle_out}
Worked out 0.2 in used
{panzer-ar57-ult-16-upper.handle_out}, harvested
How deep the opening onto the bolt goes into the receiver from the channel's floor0.3 in ± 0.1 in 7.6 mmProvisionalWorked out: {panzer-ar57-ult-16-upper.bolt_window_depth}
Worked out 0.3 in used
{panzer-ar57-ult-16-upper.bolt_window_depth}, harvested
The barrel's shoulder ahead of the takedown pin: where a muzzle device seats (its brake's rear face)17.444 in ± 0.03 in 443.1 mmProvisionalWorked out: {.brake_rear_x}
Worked out 17.444 in used
{.brake_rear_x}, harvested
The brake comes on it: the upper occupies the muzzle slot, and this is where its own brake stands.
The handguard's height, from its underside to the top the magazine lies on (the front block's rails apart)1.537 in ± 0.03 in 39 mmProvisionalWorked out: {.tray_top_y} - {.handguard_bottom_y}
Worked out 1.537 in ± 0.03 in used
{.tray_top_y} - {.handguard_bottom_y}, harvested
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
AR-15 receiver pins
- Lower receivers
- Aero Precision M4E1 complete lower, A2 grip and M4 stock, Aero Precision M4E1 Stripped Lower Receiver, Battle Arms Development Workhorse stripped lower, BCM MK2 AR-15 Lower Receiver, Bear Creek Arsenal BC-15 Multi Caliber, Lower Receiver, Black Anodized, Geissele Automatics Super Duty AR-15 Lower Receiver - Stripped Lower, Palmetto State Armory AR-15 "Stealth" Stripped Lower Receiver
Picatinny rail (MIL-STD-1913)
- Red dot mounts
- Aimpoint Duty RDS One-piece TNP Mount, 30 mm, Aimpoint LRP (Lever Release Picatinny) Mount with 39 mm Spacer, for Micro, Aimpoint One-piece Torsion Nut Mount and Spacer, 39 mm, Geissele Super Precision T1 Mount - 1.93" Height, Geissele Super Precision T1 Mount - Absolute Co-Witness, Geissele Super Precision T1 Mount - Lower 1/3 Co-Witness, Holosun 1.63 in lower 1/3 co-witness pedestal mount (HS-MOUNT-AR-RISER-ARO), Midwest Industries MK2 QD T2 Aimpoint Mount, Low, Midwest Industries MK2 QD T2 Aimpoint Mount, Lower 1/3 Cowitness, Midwest Industries MK2 QD T2 Aimpoint Mount, NV 2.26 in Height, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – 1.93″ HEIGHT, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – LOWER 1/3 (39MM HEIGHT), Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.42 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.57 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.93 in, Scalarworks LEAP/02 Aimpoint Micro T-2 quick-detach mount, 2.26 in, SIG Sauer M1913 I-BEAM Mount, 1.41 in absolute co-witness, SIG Sauer See-Through Riser Mount, 1.41 in absolute co-witness, Unity Tactical FAST Micro Mount, 2.26 in optical centerline
- Optics
- Aimpoint Patrol Rifle Optic (PRO) Red Dot Reflex Sight - QRP2 Mount, EOTECH HWS EXPS3 holographic weapon sight, 1-Dot Speed Ring, Holosun HS510C Open Reflex MRS Solar QD Mount
- Lights
- Olight Baldr S BL, Streamlight ProTac Rail Mount HL-X, SureFire Mini Scout Light Pro, SureFire Scout Light Pro Dual Fuel
- Backup sights
- Daniel Defense A1.5 Fixed Rear Sight, Daniel Defense Rail Mounted Fixed Front Sight, Magpul MBUS 3 Sight – Front, Magpul MBUS 3 Sight – Rear, Magpul MBUS Pro Sight – Front, Magpul MBUS Pro Sight – Rear
- Magnifiers
- EOTECH G33 Magnifier, STS Mount, EOTECH G45 Magnifier, STS Mount, Holosun HM3X 3× magnifier with flip mount
- Scope mounts
- Primary Arms Deluxe AR-15 Scope Mount - 30mm, Primary Arms SLx Cantilever 30mm Mount - 1.5", Reptilia AUS™ MOUNT - 30MM DIAMETER - 39MM HEIGHT, Scalarworks LEAP/08 quick-detach scope mount, 30 mm, 1.57 in, SIG SAUER ALPHA-MSR scope mount, 30 mm, Vortex Sport Cantilever 30mm Mount
Muzzle thread
- Muzzle devices
- Dead Air XRF Xeno Rimfire Muzzle Brake, HUXWRX Flash Hider-QD 556 1/2x28, Mil-spec A2 flash hider, 1/2-28 (drawing 9349051), Nordic Components 1/2-28 thread protector (ships on the 22RB), Otter Creek Labs Polonium, Otter Creek Labs Polonium K, Precision Armament M4-72 Severe-Duty® Compensator, SilencerCo Sparrow 22, SureFire ProComp 556 Muzzle Brake, SureFire SOCOM 3-Prong Flash Hider, SureFire SOCOM 4-Prong Flash Hider, SureFire WARCOMP Flash Hider, Taurus TX22 Thread Protector, VG6 Precision GAMMA 556
P90 magazine, on top of the upper
M-LOK
- Hand stops
- BCM KAG (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK Hand Stop (fit unchecked), Magpul M-LOK Index Panel (fit unchecked)
- Vertical grips
- BCM Vertical Grip Mod 3 (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK MVG vertical grip (fit unchecked)
- Lights
- Cloud Defensive REIN (fit unchecked), Streamlight ProTac Rail Mount HL-X (fit unchecked), SureFire Mini Scout Light Pro (fit unchecked), SureFire Scout Light Pro Dual Fuel (fit unchecked)
- Rail sections
- Magpul M-LOK® Aluminum Rail, 3 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 5 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 7 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 9 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 11 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 3 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 5 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 7 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 9 Slots (fit unchecked)
- Adapter plates
- Magpul M-LOK Hand Stop MOE Adapter (fit unchecked)
- Sling mounts
- Magpul M-LOK QD Sling Mount (fit unchecked)
- Rail covers
- Magpul M-LOK Rail Cover Type 2