Rail section
Magpul M-LOK® Aluminum Rail, 7 Slots
A seven-slot Picatinny rail section machined from aluminium and hard anodized black, for any M-LOK hand guard or forend: two screws and two cammed T-nuts hold it in two M-LOK slots side by side, and its recoil lugs sit in the slots. Its ends are bevelled. Magpul: "M-LOK Aluminum Rail Sections allow the attachment of various 1913 Picatinny spec rail-mounted accessories such as lights, vertical grips, etc."

- Weight
- 0.57 oz ± 0.12 oz Provisionalworked out: The rail's own aluminium: the model's volume, 0.3643 cubic inches (pipeline/blender/magpul_mlok_aluminum_rail_section.py's manifest for this length, app/public/models/magpul-mlok-aluminum-rail-section-7-slot.json volume_in3, the screws apart), times std.density.aluminium (1.568 oz to the cubic inch: the alloy isn't stated, "Machined from milspec-anodized aluminum"): 0.571 oz. The ± is the height's (± 0.03 in over its length and the width under its head) and the alloy's 4%.
- Lowest price
- $17.02 at KYGUNCO, read Nov 21, 2026
- Maker's number
- MAG582
- Colour
- Black (placeholder)
- Drawn as
- modelled
- Maker's page
- magpul.com
Added to “22RB .22 LR rifle”, a build on the start page, where the designer starts a new rail section.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Overall length (along the handguard)3.162 in ± 0.02 in 80.3 mmConflictWorked out: {.rail_slot0_x} + 6 * {std.picatinny.slot_pitch} + {.front_block}
Worked out 3.162 in ± 0.02 in used
{.rail_slot0_x} + 6 * {std.picatinny.slot_pitch} + {.front_block}, harvested
Published “7 slots, 3.3" overall length.”
KYGunCo, Magpul M-Lok Aluminum Rail Section 7 Slots (MAG582-BLK), a seller, read Oct 29, 2026 the page, harvested Oct 29, 2026
Magpul's maximum as the length: the same page also says "a max overall length of 3.3"".
Magpul's own figure is a maximum (max_length), and the part is under it; the sellers' figures repeat that maximum. Its slots on the standard's pitch and its own end blocks, each as long as the three- and five-slot's are (0.395 and 0.403 in) within their ±.
blocks and ky differ by 0.138 in beyond what each states it is good to.
The base's length, tip to tip of its arched ends.
Maximum overall length, as Magpul states it3.3 in 83.8 mmConfirmedPublished: Magpul, M-LOK Aluminum Rail Sections (GIS sheet, MAG580-MAG583_M-LOK_Aluminum_Rail_Sections_GIS_01.pdf), the maker, read Oct 29, 2026
Published “MAG582 - 7 Slots, max overall length of 3.3”” used
Magpul, M-LOK Aluminum Rail Sections (GIS sheet, MAG580-MAG583_M-LOK_Aluminum_Rail_Sections_GIS_01.pdf), the maker, read Oct 29, 2026 the page, harvested Oct 29, 2026
A bound, not the length: the test holds the length under it.
Height (its rail's top above the handguard's face it sits on)0.24 in ± 0.03 in 6.1 mmProvisionalWorked out: {magpul-mlok-aluminum-rail-section-5-slot.height}
Worked out 0.24 in ± 0.03 in used
{magpul-mlok-aluminum-rail-section-5-slot.height}, harvested
Photo 0.26 in ± 0.04 in
Midwest Gun Works, MAG582.jpg, 1500 x 1500: from above its near side, its hardware beside it, harvested
Scale: an orthographic camera from its own teeth: along it, the standard's pitch (tooth to tooth 160.5 to 167 px on the row 900, about 163: 414 px to the inch); across it, a groove's floor from its far edge to its near (298 px along the groove, as 0.80 to 0.82 in, what the views from above and below have the part at its grooves). Read by along the groove from (503, 640): the floor's near edge at 357.5 px to the base's near edge, the background, at 373.5: 16 px. Through that camera, 0.26 in with the body under the head the lower gauge line's width. Sensitive to the floor's width and the camera's elevation: the ±
The line's figure, read on the five-slot with a check on the fit; this length's own photo reads it within its ±.
The line's figure, with the reason in its source.
Width (side to side, at its widest)0.835 in ± 0.005 in 21.2 mmConfirmedWorked out: {std.picatinny.top_width}
Worked out 0.835 in ± 0.005 in used
{std.picatinny.top_width}, harvested
The head's widest is the standard's: Magpul, "various 1913 Picatinny spec rail-mounted accessories".
Width of the base's flat face (the body's foot, on the hand guard's face)0.602 in ± 0.01 in 15.3 mmProvisionalWorked out: ({magpul-mlok-aluminum-rail-section-3-slot.neck_width} + {magpul-mlok-aluminum-rail-section-9-slot.neck_width}) / 2
Worked out 0.602 in ± 0.01 in used
({magpul-mlok-aluminum-rail-section-3-slot.neck_width} + {magpul-mlok-aluminum-rail-section-9-slot.neck_width}) / 2, harvested
The section under the head: the head's lower 45 degree faces carried on past the lower gauge line until they are this wide (0.227 in under the rail's top), and upright from there to the base, as the clamps' hooks need room under the head (rail-sections.test.ts) and as the photos of the underside show the base: narrower than the head by 0.11 in each side. Until 2026-10-29 the body was drawn upright at the lower gauge line's width (.748), an assumption, and three clamps' hooks stood in it. Midwest Gun Works' photos from above show a dark band 30 px deep under the head's widest on the near side, which a body undercut so far shows only as its shadow on the white ground: said in height's note.
Rail slots7ConfirmedPublished: Magpul, M-LOK® Aluminum Rail, 7 Slots (MAG582), the maker, read Oct 29, 2026
Published “M-LOK® Aluminum Rail, 7 Slots” used
Magpul, M-LOK® Aluminum Rail, 7 Slots (MAG582), the maker, read Oct 29, 2026 the page, harvested Oct 29, 2026
Magpul's name for it; counted on its studio photo (7 grooves, 6 teeth between them and an end block at each end).
Rear rail slot's centre ahead of the part's rear end0.398 in ± 0.008 in 10.1 mmCorroboratedPhoto: Primary Arms, MAG582_00.jpg, 2200 x 1466: from above, square on, no screws
Photo 0.398 in ± 0.008 in used
Primary Arms, MAG582_00.jpg, 2200 x 1466: from above, square on, no screws, harvested
Scale: its two through holes (circles fitted to their white: 557.4 and 1652.0 px; the white seen through each is bounded at the base), six standard pitches apart at the base's plane: 463.0 px to the inch. Its grooves read 472 px to the inch at the rail's top (groove centres 549.1 and 1663.5 px): the base, 0.24 in further from the lens, 1.8% smaller. Read by the base's rear tip (373 px) to the rear hole's centre
Photo 0.404 in ± 0.015 in
Magpul's studio photo, from high over one end, harvested
Scale: its through holes six standard pitches apart at the base's plane. Read by the base's tip to the near hole along the line through the holes
Square on, at the scale of the holes in the base's plane; Magpul's steep photo agrees within its ±.
Front end block: the last rail slot's centre to the part's front end0.4 in ± 0.008 in 10.2 mmCorroboratedPhoto: Primary Arms, from above
Photo 0.4 in ± 0.008 in used
Primary Arms, from above, harvested
Scale: as for rail_slot0_x. Read by the front hole's centre to the base's front tip (1837 px): 185 px (0.3996 in)
Photo 0.394 in ± 0.015 in
Magpul's studio photo, harvested
Scale: as for rail_slot0_x. Read by the far hole to the outline's far tip along the line through the holes
As for rail_slot0_x.
Within its ± of the rear one: the part is the same both ways round.
The end bevel's run: from the base's tip in to the bevel's top edge (along the part)0.131 in ± 0.025 in 3.3 mmProvisionalWorked out: ({magpul-mlok-aluminum-rail-section-3-slot.end_bevel_run} + {magpul-mlok-aluminum-rail-section-5-slot.end_bevel_run}) / 2
Worked out 0.131 in ± 0.025 in used
({magpul-mlok-aluminum-rail-section-3-slot.end_bevel_run} + {magpul-mlok-aluminum-rail-section-5-slot.end_bevel_run}) / 2, harvested
Screws (and T-nuts) it is held by2ProvisionalPhoto: a photo on file
Photo 2 count used
a photo on file, harvested
Scale: none: a count. Read by two counterbores with their through holes in Magpul's studio photo; two screws in it on a hand guard
No seller on file states its hardware; Midwest Gun Works says two for the three- and five-slot and three for the nine-slot, one a screw.
Rail pitches from one screw to the next6ProvisionalPhoto: a photo on file
Photo 6 count used
a photo on file, harvested
Scale: its grooves, counted. Read by its through holes stand in the first, seventh grooves' floors: 6 pitches apart
The first screw stands in the first groove's floor (rail_slot0_x).
M-LOK slots its T-nuts span2ProvisionalWorked out: Two T-nuts on two screws six rail pitches apart (60 mm, one and a half M-LOK slot pitches): one in the rear half of one slot and one in the front half of the next, the closer of the two ways M-LOK places nuts 60 mm apart (Magpul's FAQ: accessories mount "entirely within a slot or bridging between/across slots"). Magpul's photo of it on a hand guard is too coarse to say which halves; the app's places a slot's interval apart offer both.
Worked out 2 count used
Two T-nuts on two screws six rail pitches apart (60 mm, one and a half M-LOK slot pitches): one in the rear half of one slot and one in the front half of the next, the closer of the two ways M-LOK places nuts 60 mm apart (Magpul's FAQ: accessories mount "entirely within a slot or bridging between/across slots"). Magpul's photo of it on a hand guard is too coarse to say which halves; the app's places a slot's interval apart offer both., harvested
Its seat on the M-LOK face: the centre of the M-LOK slot its rear T-nut is in, ahead of its rear end0.792 in ± 0.012 in 20.1 mmCorroboratedWorked out: {.rail_slot0_x} + {std.mlok.interval} / 2
Worked out 0.792 in ± 0.012 in used
{.rail_slot0_x} + {std.mlok.interval} / 2, harvested
Its two T-nuts are six rail pitches apart, 60 mm (the screws over the first and the seventh grooves): the rear one in the rear half of one slot, the front one in the front half of the next. Which halves isn't published; the app's places, half a slot apart, offer both ways the nuts can go.
Reach inside the handguard (below the mounting face, tightened)No value yetMissingNo source yet
Not published: Magpul's M-LOK tips sheet sets the nut's top level with the recoil lug's bottom edge and gives neither's size.
The screws' counterbores, across0.369 in ± 0.015 in 9.4 mmProvisionalPhoto: Primary Arms, from above
Photo 0.369 in ± 0.015 in used
Primary Arms, from above, harvested
Scale: its grooves at the rail's top: 472 px to the inch. Read by column 557 across the rear counterbore: its dark ring from 622 to 796 px (174 px), the through hole's white inside it
The screws' button heads, across0.205 in ± 0.04 in 5.2 mmProvisionalWorked out: ({magpul-mlok-aluminum-rail-section-3-slot.screw_head_d} + {magpul-mlok-aluminum-rail-section-5-slot.screw_head_d}) / 2
Worked out 0.205 in ± 0.04 in used
({magpul-mlok-aluminum-rail-section-3-slot.screw_head_d} + {magpul-mlok-aluminum-rail-section-5-slot.screw_head_d}) / 2, harvested
How far below the rail's top the screws' heads seat (the counterbore's floor)0.2 in ± 0.03 in 5.1 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows the counterbore's floor in profile. The heads are down in the counterbores below the grooves' floors in every photo with the screws in; their seat is put 0.04 in above the base.
Worked out 0.2 in ± 0.03 in used
An assumption for the drawing, not a reading: no view on file shows the counterbore's floor in profile. The heads are down in the counterbores below the grooves' floors in every photo with the screws in; their seat is put 0.04 in above the base., harvested
The screws' button heads, high0.08 in ± 0.02 in 2 mmProvisionalWorked out: An assumption for the drawing, not a reading: no camera is fitted to a photo of its screws from the side; a button head about a third as high as it is wide.
Worked out 0.08 in ± 0.02 in used
An assumption for the drawing, not a reading: no camera is fitted to a photo of its screws from the side; a button head about a third as high as it is wide., harvested
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
M-LOK
- Uppers
- Nordic Components 22RB .22 LR upper, 16" (fit unchecked), Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12" (fit unchecked), Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16" (fit unchecked)
- Handguards
- Aero Precision AR15 10.3" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 12.7" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 15" Enhanced M-LOK Handguard, Gen 2 (fit unchecked), Aero Precision AR15 15" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 15" S-ONE M-LOK Handguard (fit unchecked), Aero Precision AR15 16.6" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 7.3" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 9.3" R-ONE M-LOK handguard (fit unchecked), BCM MCMR-10 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM MCMR-13 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM MCMR-15 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM PMCR (Polymer M-LOK® Compatible Rail)* Carbine Length-BLACK (fit unchecked), BCM PMCR (Polymer M-LOK® Compatible Rail)* Mid Length-BLACK (fit unchecked), Expo Arms Free Float AR-15 Handguard - M-LOK - 15" (fit unchecked), Geissele Automatics 10.5" Super Modular Rail MK16 M-LOK (fit unchecked), Geissele Automatics 13.5" Super Modular Rail MK16 M-LOK (fit unchecked), Geissele Automatics 15" Super Modular Rail MK16 M-LOK (fit unchecked), Magpul MOE SL® Hand Guard, Carbine-Length – AR15/M4 (fit unchecked), Magpul MOE SL® Hand Guard, Mid-Length – AR15/M4 (fit unchecked), Magpul MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4 (fit unchecked), Magpul MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4 (fit unchecked), MAS Defense 12.62" NERO M-LOK FREE FLOAT (fit unchecked), MAS Defense 15" NERO M-LOK FREE FLOAT (fit unchecked), MAS Defense 9.87" NERO M-LOK FREE FLOAT (fit unchecked), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine) (fit unchecked), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length) (fit unchecked), Midwest Industries Combat Rail One Piece Free Float Handguard, M-LOK™ (15") (fit unchecked)
- Adapter plates
- Magpul M-LOK Hand Stop MOE Adapter (fit unchecked)
Picatinny rail (MIL-STD-1913)
- Red dot mounts
- Aimpoint Duty RDS One-piece TNP Mount, 30 mm, Aimpoint LRP (Lever Release Picatinny) Mount with 39 mm Spacer, for Micro, Aimpoint One-piece Torsion Nut Mount and Spacer, 39 mm, Geissele Super Precision T1 Mount - 1.93" Height, Geissele Super Precision T1 Mount - Absolute Co-Witness, Geissele Super Precision T1 Mount - Lower 1/3 Co-Witness, Holosun 1.63 in lower 1/3 co-witness pedestal mount (HS-MOUNT-AR-RISER-ARO), Midwest Industries MK2 QD T2 Aimpoint Mount, Low, Midwest Industries MK2 QD T2 Aimpoint Mount, Lower 1/3 Cowitness, Midwest Industries MK2 QD T2 Aimpoint Mount, NV 2.26 in Height, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – 1.93″ HEIGHT, Reptilia DOT MOUNT FOR AIMPOINT® MICRO – LOWER 1/3 (39MM HEIGHT), Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.42 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.57 in, Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.93 in, Scalarworks LEAP/02 Aimpoint Micro T-2 quick-detach mount, 2.26 in, SIG Sauer M1913 I-BEAM Mount, 1.41 in absolute co-witness, SIG Sauer See-Through Riser Mount, 1.41 in absolute co-witness, Unity Tactical FAST Micro Mount, 2.26 in optical centerline
- Optics
- Aimpoint Patrol Rifle Optic (PRO) Red Dot Reflex Sight - QRP2 Mount, EOTECH HWS EXPS3 holographic weapon sight, 1-Dot Speed Ring, Holosun HS510C Open Reflex MRS Solar QD Mount
- Lights
- Olight Baldr S BL, Streamlight ProTac Rail Mount HL-X, SureFire Mini Scout Light Pro, SureFire Scout Light Pro Dual Fuel
- Backup sights
- Daniel Defense A1.5 Fixed Rear Sight, Daniel Defense Rail Mounted Fixed Front Sight, Magpul MBUS 3 Sight – Front, Magpul MBUS 3 Sight – Rear, Magpul MBUS Pro Sight – Front, Magpul MBUS Pro Sight – Rear
- Magnifiers
- EOTECH G33 Magnifier, STS Mount, EOTECH G45 Magnifier, STS Mount, Holosun HM3X 3× magnifier with flip mount
- Scope mounts
- Primary Arms Deluxe AR-15 Scope Mount - 30mm, Primary Arms SLx Cantilever 30mm Mount - 1.5", Reptilia AUS™ MOUNT - 30MM DIAMETER - 39MM HEIGHT, Scalarworks LEAP/08 quick-detach scope mount, 30 mm, 1.57 in, SIG SAUER ALPHA-MSR scope mount, 30 mm, Vortex Sport Cantilever 30mm Mount
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- KYGUNCO $17.02 Nov 21, 2026, in stock that day
- Primary Arms $20.15 Nov 17, 2026, in stock that day
- Magpul $24.95 Nov 21, 2026, stock not said