Magnifier
Holosun HM3X 3× magnifier with flip mount
Flip-to-side mount, with its height spacer in (1.63 in, for a lower 1/3 co-witness sight) or out (1.41 in, absolute co-witness, as Holosun ships it): the QD lever on the rifle's left, the hinge on its right. In line behind the red dot, or swung aside to the right.

- Weight
- 9.8 oz Conflictpublished: holosun.com HM3X page, the maker, read Sep 30, 2026Its sources span 9.45 oz to 10.95 oz.
- Lowest price
- $235.28 at Holosun, read Nov 21, 2026
- Maker's number
- HM3X
- Colour
- Black (placeholder)
- Drawn as
- modelled
In “22RB .22 LR rifle”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Overall length4.03 in 102.4 mmConflictPublished: Holosun EU dimensioned drawing, the maker, read Sep 30, 2026
Published 4.03 in used
Holosun EU dimensioned drawing, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
Overall, including the eyepiece ring. The same drawing gives 3.48 in without it.
Published “4 × 1.7 × 2.5 in”
holosun.com HM3X page, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
Published “102×43×67 (L × W × H)”
Holosun HM3X manual V2.2, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
Published “100x39x62 mm”
Holosun EU shop, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
Published “39 × 100 × 62 mm without the spacer”
SPARTANAT review, a review, read Sep 30, 2026 the page, harvested Sep 30, 2026
The brief's figure. Identical to the EU listing, so possibly quoted rather than measured.
Holosun's own dimensioned drawing is the most specific source.
drawing and eu differ by 0.093 in beyond what each states it is good to.
drawing and review differ by 0.093 in beyond what each states it is good to.
manual and eu differ by 0.079 in beyond what each states it is good to.
manual and review differ by 0.079 in beyond what each states it is good to.
Width (magnifier and mount)1.66 in 42.2 mmConflictPublished: Holosun EU dimensioned drawing, the maker, read Sep 30, 2026
Published 1.66 in used
Holosun EU dimensioned drawing, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
Published “4 × 1.7 × 2.5 in”
holosun.com HM3X page, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
Published 43 mm
Holosun HM3X manual V2.2, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
Published “39 × 100 × 62 mm without the spacer”
SPARTANAT review, a review, read Sep 30, 2026 the page, harvested Sep 30, 2026
Same as the EU listing.
Dimensioned drawing.
drawing and manual differ by 0.033 in beyond what each states it is good to.
drawing and review differ by 0.125 in beyond what each states it is good to.
spec and review differ by 0.165 in beyond what each states it is good to.
manual and review differ by 0.157 in beyond what each states it is good to.
Height on mount, no spacer (housing top to the clamp jaws' bottom)2.42 in 61.5 mmConflictPublished: Holosun EU dimensioned drawing, the maker, read Sep 30, 2026
Published 2.42 in used
Holosun EU dimensioned drawing, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
Published “4 × 1.7 × 2.5 in”
holosun.com HM3X page, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
Published “39 × 100 × 62 mm without the spacer”
SPARTANAT review, a review, read Sep 30, 2026 the page, harvested Sep 30, 2026
Dimensioned drawing.
drawing and spec differ by 0.08 in beyond what each states it is good to.
M3: the drawing's 2.42 runs to the bottom of the clamp jaws, which reach 0.22 in below the rail top (clamp_below_rail); the housing top is 2.20 in above the rail (top_above_rail_no_spacer). M2 read it as housing top to rail.
Height on mount, spacer installed2.64 in 67.1 mmProvisionalWorked out: {.height} + {.spacer_thickness}
Published “102×43×67 (L × W × H)”
Holosun HM3X manual V2.2, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
The manual doesn't say, but 67 mm matches the drawing height plus the spacer (see derived).
Worked out 2.64 in used
{.height} + {.spacer_thickness}, harvested
Built from the drawing height and the manual's two center heights; agrees with the manual's 67 mm.
Spacer thickness0.22 in 5.6 mmProvisionalWorked out: {.optical_axis_above_rail_spacer} - {.optical_axis_above_rail_no_spacer}
Worked out 0.22 in used
{.optical_axis_above_rail_spacer} - {.optical_axis_above_rail_no_spacer}, harvested
Published “5mm high riser”
SPARTANAT review, a review, read Sep 30, 2026 the page, harvested Sep 30, 2026
From Holosun's own center heights. SPARTANAT's 5 mm matches its 35→40 mm heights, which disagree with Holosun's.
Lens center above rail, no spacer1.41 in 35.8 mmConflictPublished: Holosun HM3X manual V2.2, the maker, read Sep 30, 2026
Published “Without the spacer, the center height is 1.41" (Abs. CW).” used
Holosun HM3X manual V2.2, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
Published 1.41 in
Holosun EU dimensioned drawing, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
Published “line of sight height: 35.8 mm”
Holosun EU shop, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
Published 35 mm
SPARTANAT review (stated in the brief), a review the page, from the project brief
Holosun's manual, drawing and EU listing agree; the review's 35 mm is 0.8 mm lower.
manual and brief differ by 0.032 in beyond what each states it is good to.
drawing and brief differ by 0.032 in beyond what each states it is good to.
eu and brief differ by 0.031 in beyond what each states it is good to.
Lens center above rail, spacer installed1.63 in 41.4 mmConflictPublished: Holosun HM3X manual V2.2, the maker, read Sep 30, 2026
Published “With the spacer, the center height is 1.63" (Lower 1/3 CW).” used
Holosun HM3X manual V2.2, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
Published 40 mm
SPARTANAT review (stated in the brief), a review the page, from the project brief
Manufacturer figure, designed to match lower-1/3 red dots such as the ARO (1.63 in). The review's 40 mm is 1.4 mm lower. Caliper to confirm.
manual and brief differ by 0.055 in beyond what each states it is good to.
Eye relief2.756 in 70 mmConfirmedPublished: holosun.com HM3X page, the maker, read Sep 30, 2026
Published “Eye Relief 70mm” used
holosun.com HM3X page, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
From the page's OPTICAL DATA table; its text says "70mm (2.75 inch) eye relief".
Eyepiece's rear face, behind the mount base's centre2.995 in ± 0.02 in 76.1 mmProvisionalPhoto: Holosun dimensioned drawing, side view (inches)
Photo 2.995 in ± 0.02 in used
Holosun dimensioned drawing, side view (inches), harvested
Scale: frame from the reviewed holes base_front_bottom, base_rear_bottom, base_front_top, base_rear_top, axis, interface, rail (214.1 px/in, rms 0.003 in over 7 points). Read by −x_min of the traced outline (tools/trace.py); the eyepiece ring's rear face, behind the mount base's centre
Where the eye looks in: the eye relief runs back from here. Holosun's drawing dimensions the overall length (4.03) and the base (1.93), not where one sits along the other, so this is read off the traced outline of that drawing.
Housing length, objective end to the eyepiece ring3.48 in 88.4 mmConfirmedPublished: Holosun EU dimensioned drawing, the maker, read Sep 30, 2026
Published 3.48 in used
Holosun EU dimensioned drawing, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
Read as objective end to where the diopter (eyepiece) ring starts.
Objective-end ring outside diameter1.32 in 33.5 mmConfirmedPublished: Holosun EU dimensioned drawing, the maker, read Sep 30, 2026
Published 1.32 in used
Holosun EU dimensioned drawing, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
The left ring as drawn. Taken as the objective end because the larger right ring is the diopter ring.
Eyepiece (diopter) ring outside diameter1.42 in 36.1 mmConfirmedPublished: Holosun EU dimensioned drawing, the maker, read Sep 30, 2026
Published 1.42 in used
Holosun EU dimensioned drawing, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
Flip-mount base length1.93 in 49 mmConfirmedPublished: Holosun EU dimensioned drawing, the maker, read Sep 30, 2026
Published 1.93 in used
Holosun EU dimensioned drawing, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
What the drawing's 1.93 spans (read 2026-10-05, for the hinge): its front extension line is the front knuckle's front face and its rear one the adjustment tool's knob's rear end (hinge_block_length, tool_knob_length: the right side view has them 1.88 apart), not the base's two ends; the base is as long as the hinge block, 1.73 in (base_plate_length), its front at the front extension line and its rear 0.2 in short of the rear one. The part frame's origin is the middle of the 1.93, as traced.
Housing top to the body/mount interface1.76 in 44.7 mmConfirmedPublished: Holosun EU dimensioned drawing, the maker, read Sep 30, 2026
Published 1.76 in used
Holosun EU dimensioned drawing, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
Optical axis to the body/mount interface0.97 in 24.6 mmConfirmedPublished: Holosun EU dimensioned drawing, the maker, read Sep 30, 2026
Published 0.97 in used
Holosun EU dimensioned drawing, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
The spacer goes in at this interface.
Housing top above the rail top, no spacer2.2 in ± 0.015 in 55.9 mmProvisionalWorked out: {.optical_axis_above_rail_no_spacer} + {.top_to_mount_interface} - {.axis_to_mount_interface}
Worked out 2.2 in ± 0.015 in used
{.optical_axis_above_rail_no_spacer} + {.top_to_mount_interface} - {.axis_to_mount_interface}, harvested
The drawing's end view: axis 1.41 above the rail, the housing top 1.76 − 0.97 = 0.79 above the axis.
Clamp jaws' bottom below the rail top0.22 in ± 0.02 in 5.6 mmProvisionalWorked out: {.height} - {.top_above_rail_no_spacer}
Worked out 0.22 in ± 0.02 in used
{.height} - {.top_above_rail_no_spacer}, harvested
The drawing's 2.42 (top to the jaws' bottom) less the housing top's 2.20 above the rail. The jaws wrap the rail's sides.
Eyepiece glass, visible diameter0.912 in ± 0.015 in 23.2 mmProvisionalPhoto: Holosun's dimensioned drawing, end view
Photo 0.912 in ± 0.015 in used
Holosun's dimensioned drawing, end view, harvested
Scale: the end view's least-squares frame on its dimension lines (214 px/in, rms 0.003 in). Read by least-squares circle through the innermost circle's line pixels about the axis (radius 97.64 px, rms 1.6 px over 1,203 px), diameter at the line's centre; ± is half the line width and the fit
Draws the eyepiece lens (M5). Read on the drawing's end view, which is seen from the objective end (the seed's notes, 2026-10-05; when this was read it was taken as seen from the eyepiece): its concentric circles about the axis are that end's, and the innermost carries the retainer's six tabs and bounds the glass. Holosun's straight end-on picture from the same end (7994638176a5) shows the glass inside the six-tabbed retainer at about 0.66 of the fluted ring's width, which the drawing's 0.62 of its outer ring roughly matches (the flutes and the tabs make that a loose check). So the figure is the glass at the objective end, where a second reading agrees with it (objective_glass_d, 0.906); it stands for the eyepiece's too, no view on file looking square into the eyepiece.
Objective glass, visible diameter0.906 in ± 0.035 in 23 mmProvisionalPhoto: holosun.com, objective end, angled from above
Photo 0.906 in ± 0.035 in used
holosun.com, objective end, angled from above, harvested
Scale: holosun-hm3x.objective_ring_od (1.32 in, the drawing) in the same plane. Read by horizontal widths through the centre: glass inside the bevel 206 px, ring 300 px (ratio 0.687) × 1.32; ± covers the bevel's edges (±5 px) and the view's slight angle
Draws the objective lens (M5). No straight view of the objective end; in Holosun's angled one the glass and the objective ring are concentric circles in one plane, so the ratio of their widths survives the angle (weak perspective). Agrees with the eyepiece glass (0.912) and the reviews' '24 mm' (0.945, no source on file).
How far the magnifier swings to the side on its mount90°ConfirmedPublished: Holosun HM3X manual V2.2, the maker, read Sep 30, 2026
Published “The magnifier can be flipped to the side 90 degrees (as shown in Figure 3).” used
Holosun HM3X manual V2.2, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
To the rifle's right: the hinge is on that side (the part's own notes on which side is which), and the manual's Figure 3 draws it swung over, lying beside the mount with its eyepiece still to the rear.
The flip mount's hinge axis above the rail top0.44 in ± 0.025 in 11.2 mmProvisionalPhoto: holosun.com's gallery: the magnifier's right side, square on, 1000 px
Photo 0.44 in ± 0.025 in used
holosun.com's gallery: the magnifier's right side, square on, 1000 px, harvested
Scale: holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of. Read by the barrel's lit band between the knuckles, rows 636.5 to 701.5 at half its brightness (feet 631 to 706), its middle at row 669. The knuckle's top (0.709 above the rail in the drawing's end view) is at row 608 and the jaws' bottom (clamp_below_rail) at 815: the picture has those 0.957 in apart where the drawing has 0.930, so the middle is 0.427 from the one and 0.454 from the other, and the ± covers both
The hinge is a barrel between two knuckles on the mount's right side, along the rail. Its middle is level with the face the magnifier's foot sits on (0.44: optical_axis_above_rail_no_spacer less axis_to_mount_interface), as a plate hinged at its own top face would have it.
The flip mount's hinge axis to the right of the optical axis's vertical0.47 in ± 0.025 in 11.9 mmProvisionalPhoto: Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px
Photo 0.47 in ± 0.025 in used
Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px, harvested
Scale: the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both. Read by the barrel's edges at columns 1340 and 1588, its middle 333 px right of the plate's centre pin (column 1131, which is the middle of the mount by the drawing's end view within 0.002 in): 0.477 at one scale, 0.464 at the other
The hinge barrel's diameter0.35 in ± 0.02 in 8.9 mmCorroboratedPhoto: Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px
Photo 0.35 in ± 0.02 in used
Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px, harvested
Scale: the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both. Read by the barrel between the knuckles, columns 1340 to 1588 (248 px): 0.355 and 0.346 at the two scales
Photo 0.32 in ± 0.03 in
holosun.com's gallery: the magnifier's right side, square on, 1000 px, harvested
Scale: holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of. Read by the barrel's lit band: 65 px at half its brightness, 75 px between its feet (0.30 to 0.35); a round bar lit from above darkens before its edge, so the band is a lower bound
From above the barrel is seen against the darker plate and gap beside it, edge to edge; from the side only its lit band shows. The two agree within their ±.
The hinge block's length along the rail (both knuckles and the barrel between them)1.728 in ± 0.015 in 43.9 mmCorroboratedPhoto: holosun.com's gallery: the magnifier's right side, square on, 1000 px
Photo 1.728 in ± 0.015 in used
holosun.com's gallery: the magnifier's right side, square on, 1000 px, harvested
Scale: holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of. Read by the block's rear and front faces at columns 535 and 909 (374 px)
Photo 1.729 in ± 0.02 in
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, the trace's). Read by the traced outline: the front knuckle's front face at 0.967 and, behind the body's foot, a face as tall as the barrel at -0.762
The view that shows the block itself; the drawing's side view, of the other side, has its two ends where this puts them.
Its front end is the mount's front end: the drawing's side view has a block as tall as the knuckles (0.712 above the rail) from 0.633 to 0.967 ahead of the base's middle, the 1.93 in base's front extension line at 0.965.
Each hinge knuckle's length along the rail0.35 in ± 0.02 in 8.9 mmCorroboratedPhoto: holosun.com's gallery: the magnifier's right side, square on, 1000 px
Photo 0.35 in ± 0.02 in used
holosun.com's gallery: the magnifier's right side, square on, 1000 px, harvested
Scale: holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of. Read by the rear knuckle columns 535 to 610 (0.347), the front 832 to 909 (0.356), the barrel's ends the dark seams between
Photo 0.334 in ± 0.02 in
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, the trace's). Read by the traced outline's front block, 0.633 to 0.967
Both knuckles and their seams show in it.
The mount's side under the hinge barrel: its top above the rail top0.21 in ± 0.02 in 5.3 mmProvisionalPhoto: holosun.com's gallery: the magnifier's right side, square on, 1000 px
Photo 0.21 in ± 0.02 in used
holosun.com's gallery: the magnifier's right side, square on, 1000 px, harvested
Scale: holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of. Read by the floor of the gap the barrel lies in, row 718: 0.201 from the knuckle's top, 0.227 from the jaws' bottom (see hinge_axis_above_rail)
The hinge knuckles' inner face, right of the optical axis's vertical0.215 in ± 0.02 in 5.5 mmProvisionalPhoto: Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px
Photo 0.215 in ± 0.02 in used
Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px, harvested
Scale: the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both. Read by the knuckles' inner edge at column 1283, 152 px right of the plate's centre pin: 0.218 and 0.212
Their outer face is the drawing's end view's (0.655, the traced outline); the inner one is behind the magnifier's foot there.
The mount base's top face above the rail top (what the flip plate lies on)0.287 in ± 0.01 in 7.3 mmProvisionalPhoto: Holosun's dimensioned drawing, end view
Photo 0.287 in ± 0.01 in used
Holosun's dimensioned drawing, end view, harvested
Scale: the end view's frame on its own dimension lines (214.4 px/in, rms 0.001 in: the trace's). Read by the traced outline's level stretch on the lever's side of the foot, from 0.26 to 0.56 left of the middle
The mount's base, along the rail1.73 in ± 0.015 in 43.9 mmConflictPhoto: Holosun's dimensioned drawing, side view
Photo 1.6 in ± 0.04 in
Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px, harvested
Scale: the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both. Read by the plate's front and rear edges, rows 504 and 1636 (1132 px): 1.62 and 1.58
Not a view square down on the mount: it is taken from above and behind, and the knuckles' tops stand 0.42 in nearer the lens than the plate's, so the hinge block reads longer than the plate (1208 px against 1132) and leans forward of it (112 px at the front, 36 behind at the rear). Read as the plate being shorter, which is the photo's lean.
Photo 1.73 in ± 0.015 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25. Read by the base's front face at column 341.5 (rows 1150 to 1284) and its rear face at 712 (rows 1150 to 1190): 370.5 px. No line parts the base's front face from the front knuckle's in this view
The maker's own side view, square on and to scale, against one photo taken aslant from above and behind, in which what stands nearer the lens leans forward. Two more sources have the base as long as the hinge block and flush with its front: Primary Arms' photo of the left side (7602cbc9ffbd: the base's upper ledge 850 px at 479 px/in, 1.77 in, from column 110 to 960) and the manual's Figure 4, which draws the base's front face and the front knuckle's as one face.
plan and drawing differ by 0.13 in beyond what each states it is good to.
As long as the hinge block beside it (hinge_block_length, 1.728) and flush with it at the front: one block in the drawing's side view, from the front knuckle's front face to a rear face 0.765 in behind the mount's middle. Read first (2026-10-05) between the top face's two edges on the picture of the mount from above, 1.6 in, with its front edge 0.16 in behind the front knuckle's (base_plate_front_behind_hinge_front): the base was drawn that long, and the rail channel under it, until 2026-10-13.
The base's front face, behind the hinge block's front end0 in ± 0.01 in 0 mmConflictPhoto: Holosun's dimensioned drawing, side view
Photo 0.16 in ± 0.03 in
Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px, harvested
Scale: the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both. Read by rows 392 (the front knuckle's front) and 504 (the plate's): 112 px
The knuckle's top is 0.42 in nearer the lens than the plate's, in a view from above and behind: it leans forward in the picture by about this much.
Photo 0 in ± 0.01 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25. Read by one upright line is the front of both: column 341.5 along rows 1190 to 1284, where the base is, and 342.5 to 343 along rows 1150 and 1175, where the knuckle stands over it (a pixel and a half: 0.007 in). ± is two pixels
The drawing's side view has one front face for the base and the front knuckle, as the manual's Figure 4 draws them and as Primary Arms' photo of the left side has the base's ledge run forward of the far knuckle; the 0.16 in is the knuckle's lean in a photo taken from above and behind (base_plate_length's reason).
plan and drawing differ by 0.16 in beyond what each states it is good to.
Nothing: the two are one face (the drawing's side view, and the manual's Figure 4). The picture of the mount from above has the top face's front edge 0.16 in behind the front knuckle's, the knuckle standing nearer a lens that looks from above and behind (base_plate_length).
The flip plate the magnifier's foot is screwed to: its length along the rail1 in ± 0.04 in 25.4 mmProvisionalPhoto: Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px
Photo 1 in ± 0.04 in used
Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px, harvested
Scale: the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both. Read by rows 664 to 1373 (709 px): 1.015 and 0.989
As long as the barrel it is one piece with, and between the knuckles with it.
The flip plate's width across the rail0.58 in ± 0.02 in 14.7 mmProvisionalPhoto: Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px
Photo 0.58 in ± 0.02 in used
Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px, harvested
Scale: the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both. Read by columns 927 to 1336 (409 px), centred on its pin: 0.585 and 0.570. The foot above it in the drawing's end view is 0.595 wide
The flip plate's two screws, apart along the rail0.69 in ± 0.02 in 17.5 mmProvisionalPhoto: Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px
Photo 0.69 in ± 0.02 in used
Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px, harvested
Scale: the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both. Read by the two holes' centres, rows 800 and 1291 (491 px): 0.703 and 0.685
The screws that hold the magnifier's foot, put in from the plate's underside (the manual's Figure 4): their heads show on it when the magnifier is swung aside (Figure 3).
The flip plate's screw holes, across0.16 in ± 0.03 in 4.1 mmProvisionalPhoto: Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px
Photo 0.16 in ± 0.03 in used
Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px, harvested
Scale: the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both. Read by each hole about 110 px across at its mouth
The adjustment tool's knurled knob, across0.3 in ± 0.02 in 7.6 mmProvisionalPhoto: holosun.com's gallery: the magnifier's right side, square on, 1000 px
Photo 0.3 in ± 0.02 in used
holosun.com's gallery: the magnifier's right side, square on, 1000 px, harvested
Scale: holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of. Read by rows 695 to 760 (65 px); from above it is 220 px across (0.31)
The manual's Figure 1 names it: the tool stowed in the mount under the hinge's rear end, its knob standing out to the rear.
The adjustment tool's knob, out of the rear knuckle's rear face0.208 in ± 0.02 in 5.3 mmProvisionalPhoto: holosun.com's gallery: the magnifier's right side, square on, 1000 px
Photo 0.208 in ± 0.02 in used
holosun.com's gallery: the magnifier's right side, square on, 1000 px, harvested
Scale: holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of. Read by columns 490 to 535 (45 px)
Its rear end is the mount's: the drawing's rear extension line (half of mount_base_length behind the middle) is 0.969 behind by this picture.
The adjustment tool's knob: its axis above the rail top0.17 in ± 0.025 in 4.3 mmProvisionalPhoto: holosun.com's gallery: the magnifier's right side, square on, 1000 px
Photo 0.17 in ± 0.025 in used
holosun.com's gallery: the magnifier's right side, square on, 1000 px, harvested
Scale: holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of. Read by its middle at row 727.5: 0.157 from the knuckle's top, 0.183 from the jaws' bottom (see hinge_axis_above_rail)
The adjustment tool's knob: its axis right of the optical axis's vertical0.42 in ± 0.03 in 10.7 mmProvisionalPhoto: Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px
Photo 0.42 in ± 0.03 in used
Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px, harvested
Scale: the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both. Read by its middle at column 1430, 299 px right of the plate's centre pin: 0.428 and 0.417
The hinge's rear end (the tension screw's boss), out of the rear knuckle's rear face0.16 in ± 0.02 in 4.1 mmProvisionalPhoto: holosun.com's gallery: the magnifier's right side, square on, 1000 px
Photo 0.16 in ± 0.02 in used
holosun.com's gallery: the magnifier's right side, square on, 1000 px, harvested
Scale: holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of. Read by columns 500 to 535 (35 px), rows 625 to 700
The manual's Figure 1 names the slotted head in it the tension screw. As wide as the barrel in this view (75 px).
The clamp's cross bolt: its head on the mount's right face, across0.32 in ± 0.02 in 8.1 mmProvisionalPhoto: holosun.com's gallery: the magnifier's right side, square on, 1000 px
Photo 0.32 in ± 0.02 in used
holosun.com's gallery: the magnifier's right side, square on, 1000 px, harvested
Scale: holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of. Read by columns 688 to 757 (69 px)
The clamp's cross bolt, behind the hinge block's front end0.864 in ± 0.02 in 21.9 mmProvisionalPhoto: holosun.com's gallery: the magnifier's right side, square on, 1000 px
Photo 0.864 in ± 0.02 in used
holosun.com's gallery: the magnifier's right side, square on, 1000 px, harvested
Scale: holosun-hm3x.length across the picture (872 px: 216.4 px/in) and holosun-hm3x.eyepiece_ring_od upright in it (306 px: 215.5 px/in): one scale both ways, a view with no perspective to speak of. Read by its head's middle at column 722, the block's front at 909 (187 px)
At the rail top's level by the same picture (row 765: 0.017 under it from the knuckle's top, 0.010 over it from the jaws' bottom), under the middle of the barrel.
Objective ring: its flutes, counted round the whole turn16ProvisionalPhoto: Holosun EU's gallery: the magnifier on its mount from the objective end, square on, 2200 px; a rendering from close by
Photo 16 count used
Holosun EU's gallery: the magnifier on its mount from the objective end, square on, 2200 px; a rendering from close by, harvested
Scale: none needed: a count. The outline unwrapped about the ring's centre (1094.9, 750.8; radius 377.1 px to the lands), a working script and rim.py. Read by the outline's radius every half degree from 60 below the picture's right round over the top to 240 (the foot hides the rest): notches 5.9 px deep with their middles at -44.8, -22.2, 0.2, 22.5, 44.8, 64.8 and, past the top boss, 115, 134.5, 154, 180 degrees: one every 22.5 degrees, sixteen to the turn. Checked on the left side, which shows half the turn: the dark walls in Primary Arms' photo (7602cbc9ffbd, rows 234, 430, 554, 677 and 757 of a ring whose silhouette is rows 194.5 to 826) are at 61.0, 14.7, -8.0, -31.9 and -51.4 degrees above the axis, five flutes in 112.4 degrees: 22.5 apart (the wall between the first two doesn't show)
Wide and shallow, open at both ends of the ring: they notch its front rim, which is the outline of Holosun's view from the objective end, and its rear edge is scalloped by them in Primary Arms' photo of the left side (7602cbc9ffbd, columns 270 to 285). The ring doesn't turn; the notches stand at the top, the bottom and both sides. The manual's line drawings (its cover, Figures 1 and 8) draw both rings with many narrow flutes: an earlier drawing of the housing, not what the photos or the dimensioned drawing's side view have.
Objective ring: how deep its flutes are0.01 in ± 0.002 in 0.3 mmProvisionalPhoto: Holosun EU's gallery: the magnifier on its mount from the objective end, square on, 2200 px; a rendering from close by
Photo 0.0103 in ± 0.002 in used
Holosun EU's gallery: the magnifier on its mount from the objective end, square on, 2200 px; a rendering from close by, harvested
Scale: holosun-hm3x.objective_ring_od (1.32 in) across the same rim, whose lands are 377.1 px from its centre: 571 px/in at the rim, where the notches are read. Read by the outline less a smooth curve through its lands: each notch's floor is 5.8 to 6.1 px inside it, over nine notches (5.9: 0.0103 in). ± is half a pixel and the ring's diameter
Objective ring: each flute's floor, as an angle round the axis8.5° ± 1°ProvisionalPhoto: Holosun EU's gallery: the magnifier on its mount from the objective end, square on, 2200 px; a rendering from close by
Photo 8.5 deg ± 1 deg used
Holosun EU's gallery: the magnifier on its mount from the objective end, square on, 2200 px; a rendering from close by, harvested
Scale: the ring's own turn: angles about its centre (1094.9, 750.8), a degree being 6.6 px along the rim. Read by where the outline is level at the notch's depth: -26 to -18, -4 to 5, 18.5 to 27, 41 to 49.5 degrees; the lands level from -37 to -29.5, -15 to -7, 8 to 16, 30 to 38, 52 to 60
The lands between are as wide (8.5 degrees), and a sloping wall joins each floor to each land (objective_ring_flute_wall): 8.5 + 2.75 + 8.5 + 2.75 = 22.5 degrees, a sixteenth of the turn.
Objective ring: each flute's sloping wall, as an angle round the axis2.8° ± 0.75°ProvisionalPhoto: Holosun EU's gallery: the magnifier on its mount from the objective end, square on, 2200 px; a rendering from close by
Photo 2.75 deg ± 0.75 deg used
Holosun EU's gallery: the magnifier on its mount from the objective end, square on, 2200 px; a rendering from close by, harvested
Scale: the ring's own turn: angles about its centre (1094.9, 750.8), a degree being 6.6 px along the rim. Read by the outline falls from a land to a floor over 2.5 to 3 degrees at each of eighteen walls (0.032 in along the rim for 0.010 in of depth: a slope of about 18 degrees, which is why the flutes are soft bands in the photos and not lines). Primary Arms' photo of the left side has one such wall as a dark band 12 px wide where this predicts 11.8 (7602cbc9ffbd, rows 428 to 440)
Objective ring: its length along the axis0.348 in ± 0.012 in 8.8 mmProvisionalPhoto: Primary Arms' HM3X_01.jpg: the left side, square on, 2200 px
Photo 0.348 in ± 0.012 in used
Primary Arms' HM3X_01.jpg: the left side, square on, 2200 px, harvested
Scale: the two rings in the same photo, upright in it: the eyepiece ring's silhouette rows 176.5 to 860.2 for holosun-hm3x.eyepiece_ring_od (481.5 px/in), the objective ring's 194.5 to 826 for holosun-hm3x.objective_ring_od (478.4). Read by the ring's front rim at column 111.5 and the dark line at its rear edge at 278 (272 to 284) along rows 520 to 545: 166.5 px. Holosun's picture of the left side has it 73 px at 216 px/in (0.338), and the drawing's traced side outline from its shoulder 0.712 ahead of the mount's middle to its front face at 1.046 (0.334; the outline's corner there, where the drawing's extension lines meet it, reaches 1.065). The model's flutes run between the outline's own shoulder and face
From the housing's front face back to the ring's rear edge, where a neck a hundredth of an inch lower begins: the flutes run its whole length.
Eyepiece (diopter) ring: its flutes, counted round the whole turn14ProvisionalPhoto: Primary Arms' HM3X_01.jpg: the left side, square on, 2200 px
Photo 14 count used
Primary Arms' HM3X_01.jpg: the left side, square on, 2200 px, harvested
Scale: none needed: a count. The ring's own silhouette, rows 176.5 to 860.2 (its axis at row 518.35, its radius 341.85 px), sets each row's angle. Read by the flutes' upper walls are sharp dark lines 4 to 5 px wide at rows 228.5, 335.5, 483 and 642: 58.0, 32.3, 5.9 and -21.2 degrees above the axis as read, 26.4 apart (the lit lower walls at rows 282.5, 418, 573.5 and 717.5 likewise). Fitted with the lens's distance left free, fourteen flutes meet the four lines within 0.3 to 0.8 degrees, thirteen within 1.5 to 2.2 and fifteen within 1.2 to 2.7 (the best fit: fourteen with the lens about 24 in away, where the objective ring's sixteen, known from its end, read 23.3 degrees apart about its middle as they do: rows 430, 554, 677). The turn closes on a whole number
Fourteen, where the objective ring has sixteen. No picture on file looks straight at this ring's end, so it is counted on a side, which shows half the turn, by the angle between flutes: a row y of the ring is asin((y - yc) / R) round the axis. A photo from near enough reads what faces the lens a few per cent large against the silhouette, so the rows are tried against thirteen, fourteen and fifteen flutes with the lens anywhere from 12 in away to infinitely far: fourteen fits best at every distance. Holosun's own side pictures are taken from closer still and agree (26.5 to 27 degrees as read; never the objective ring's 22.5). The ring turns (the manual: "Rotate the diopter adjustment with your thumb and forefinger"); it is drawn as this photo has it, a flute at each side and a land at the top.
Eyepiece ring: each flute, as an angle round the axis at the ring's surface14.8° ± 1.2°ProvisionalPhoto: Primary Arms' HM3X_01.jpg: the left side, square on, 2200 px
Photo 14.8 deg ± 1.2 deg used
Primary Arms' HM3X_01.jpg: the left side, square on, 2200 px, harvested
Scale: the ring's own silhouette, rows 176.5 to 860.2 (its axis at row 518.35, its radius 341.85 px), sets each row's angle. Read by from each dark upper wall to the lit lower wall under it: rows 228.5 to 282.5 (58.0 to 43.6 degrees: 14.4), 335.5 to 418 (32.3 to 17.1: 15.3), 483 to 573.5 (5.9 to -9.3: 15.2); 15.0 as read, of 26.4 from flute to flute where fourteen flutes are 25.7 apart, so 14.6 to 15.0 of the turn's fourteenth. Holosun's picture of the left side has one from row 385 to 424 of a ring of radius 144.4 px (15.6 as read, from closer). ± covers the spread and a wall's own 4 to 5 px
Flat-floored pockets with steep walls, wider than the lands between them (10.9 degrees). Which is which: the photo is lit from above, and each wide band has a shadowed line along its upper edge and a lit one along its lower, as a recess has.
Eyepiece ring: how far short of each end of the ring its flutes stop0.03 in ± 0.012 in 0.8 mmProvisionalPhoto: Primary Arms' HM3X_01.jpg: the left side, square on, 2200 px
Photo 0.03 in ± 0.012 in used
Primary Arms' HM3X_01.jpg: the left side, square on, 2200 px, harvested
Scale: holosun-hm3x.eyepiece_ring_od upright in the same photo (683.7 px: 481.5 px/in). Read by along rows 345 to 400 and 500 to 560, inside two flutes: the ring runs from column 1901 (the dark gap before it ends) to its rear rim at 2096; the flute's end walls are the lit lines at 1915 to 1918 and 2077 to 2083 (14 to 17 px from the one end, 13 to 19 from the other)
Closed at both ends, unlike the objective ring's: the ring's rear rim has no notch in it (its outline in Holosun's view from the rear right, d8dddfb5eb56, keeps within 0.1 px of a smooth curve over 115 degrees of the turn). So no edge shows how deep they are, and that is not read: they are drawn as deep as the objective ring's.
Eyepiece ring: its length along the axis0.405 in ± 0.012 in 10.3 mmProvisionalPhoto: Primary Arms' HM3X_01.jpg: the left side, square on, 2200 px
Photo 0.405 in ± 0.012 in used
Primary Arms' HM3X_01.jpg: the left side, square on, 2200 px, harvested
Scale: holosun-hm3x.eyepiece_ring_od upright in the same photo (683.7 px: 481.5 px/in). Read by columns 1901 to 2096 along rows 345 to 400 (195 px). Holosun's picture of the left side has it 88 px at 216 px/in (0.407), and the drawing's traced side outline from 2.995 to 2.602 behind the mount's middle (0.393)
The mount base's left face (the wall the lever lies along), left of the optical axis's vertical0.604 in ± 0.012 in 15.3 mmProvisionalPhoto: Holosun's dimensioned drawing, end view
Photo 0.604 in ± 0.012 in used
Holosun's dimensioned drawing, end view, harvested
Scale: the end view's frame on its own dimension lines (214.4 px/in, rms 0.001 in: the trace's), its middle at column 1612.3. Read by the upright line the lever's ears stand on, columns 1741 to 1742 along rows 1224, 1247 and 1267 (1741.7). The same view's traced outline has the lever's own outer edge at 0.873
The QD lever's pivot (the roller between its two ears), ahead of the mount's middle0.097 in ± 0.012 in 2.5 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.097 in ± 0.012 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25. Read by the roller's two sides at columns 505.5 and 549.5 along row 1242: its middle at 527.5
The QD lever's roller, across0.206 in ± 0.012 in 5.2 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.206 in ± 0.012 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25. Read by columns 505.5 to 549.5 along row 1242 (44 px)
Bright steel in Holosun's pictures (a dark grey bush in Primary Arms'), upright between the lever's two ears; the clamp's cross bolt ends in it.
The QD lever's roller: its top (the upper ear's underside) above the rail top0.073 in ± 0.01 in 1.9 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.073 in ± 0.01 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the rail top at row 1247.19. Read by the line at rows 1230 to 1233 down columns 520 and 545 (1231.5); the end view has the same line at the same rows
The QD lever's roller: its bottom (the lower ear's top) below the rail top0.036 in ± 0.01 in 0.9 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.036 in ± 0.01 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the rail top at row 1247.19. Read by the line at rows 1252 to 1256 down columns 520 and 545 (1255); the end view has the same line at the same rows
The QD lever's two ears about its pivot, across0.19 in ± 0.02 in 4.8 mmProvisionalPhoto: Holosun EU's gallery: the magnifier on its mount from below, the objective end down, 2200 px
Photo 0.19 in ± 0.02 in used
Holosun EU's gallery: the magnifier on its mount from below, the objective end down, 2200 px, harvested
Scale: the rail channel's roof in the same photo, columns 985 to 1310 (325 px) for the 0.653 in the drawing's traced end outline has between its two edges: 498 px/in; the jaws' underside front to rear (rows 990 to 1770 for the traced side outline's 1.546 in) gives 504. Read by the pivot pin's middle at column 748 and the ear's outer edge at 700 along row 1345: 48 px, doubled. The picture of the mount from above (9b4d7ab4e4c7) has 65 px from the pin's middle to the ear's edge at about 705 px/in (0.184 across)
Round about the pivot pin from below and from above. The ears' outer end is the mount's left extreme: 0.877 in left of the middle here, 0.873 in the drawing's traced end outline. That drawing's end view has the ears' lines from column 1750.5 to 1798 (0.222 in): more than the round, the ears running on inboard toward the clamp's nose.
The QD lever's upper edge above the rail top0.203 in ± 0.01 in 5.2 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.203 in ± 0.01 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the rail top at row 1247.19. Read by the line along the lever at rows 1203 to 1204.5 down columns 495 to 695 (1203.75)
The QD lever's lower edge below the rail top0.163 in ± 0.01 in 4.1 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.163 in ± 0.01 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the rail top at row 1247.19. Read by the line along the lever at rows 1281.5 to 1282.5 down columns 495 to 660 (1282)
The QD lever's rear end (its ribbed pad's), behind the mount's middle0.91 in ± 0.015 in 23.1 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.91 in ± 0.015 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25. Read by the pad's dark run ends at column 742 along row 1270 and 743 along 1242 (743)
Past the base's rear face (0.765 behind) by 0.145 in: the pad is what a thumb takes.
The QD lever's ribbed pad, along the lever0.206 in ± 0.015 in 5.2 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.206 in ± 0.015 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25. Read by the ribs begin at column 699 (rows 1215 to 1270) and the pad ends at 743: 44 px
Its ribs run across the lever, seven grooves 0.029 in apart in Holosun's picture of the left side (5ee8dd2e6815, columns 460 to 498 along rows 728 to 760: a groove 0.012 in wide). Finer than a page draws: the pad is drawn plain.
The QD lever's arm, across (how thick it is, seen from above or below)0.09 in ± 0.025 in 2.3 mmProvisionalPhoto: Holosun EU's gallery: the magnifier on its mount from below, the objective end down, 2200 px
Photo 0.09 in ± 0.025 in used
Holosun EU's gallery: the magnifier on its mount from below, the objective end down, 2200 px, harvested
Scale: the rail channel's roof in the same photo, columns 985 to 1310 (325 px) for the 0.653 in the drawing's traced end outline has between its two edges: 498 px/in; the jaws' underside front to rear (rows 990 to 1770 for the traced side outline's 1.546 in) gives 504. Read by along row 1100 the arm's lit face is columns 743 to 777 and its shaded inner edge runs to 790 (34 to 47 px: 0.07 to 0.095 in). The picture of the mount from above (9b4d7ab4e4c7) has it 82 px along row 1320 at about 705 px/in (0.116), the lever standing open there and seen aslant. ± covers the three
The QD lever's rear end: its outer face, out from the base's left wall0.18 in ± 0.03 in 4.6 mmProvisionalPhoto: Holosun EU's gallery: the magnifier on its mount from below, the objective end down, 2200 px
Photo 0.18 in ± 0.03 in used
Holosun EU's gallery: the magnifier on its mount from below, the objective end down, 2200 px, harvested
Scale: the rail channel's roof in the same photo, columns 985 to 1310 (325 px) for the 0.653 in the drawing's traced end outline has between its two edges: 498 px/in; the jaws' underside front to rear (rows 990 to 1770 for the traced side outline's 1.546 in) gives 504. Read by the arm's outer edge at column 751.5 along row 1020, and the base's side at column 839 (the front block's face, 836 to 842, which is the wall: 0.604 in left of the middle at this scale): 87.5 px
Less than at the pivot (0.27 in, the ears' outer end in the drawing's end view): closed, the arm leans in toward the base and lies on the catch block behind it (lever_catch_proud + lever_arm_thickness = 0.175).
The block on the base's left wall that the lever's rear end latches on: its length along the rail0.36 in ± 0.04 in 9.1 mmProvisionalPhoto: Holosun EU's gallery: the magnifier on its mount from below, the objective end down, 2200 px
Photo 0.36 in ± 0.04 in used
Holosun EU's gallery: the magnifier on its mount from below, the objective end down, 2200 px, harvested
Scale: the rail channel's roof in the same photo, columns 985 to 1310 (325 px) for the 0.653 in the drawing's traced end outline has between its two edges: 498 px/in; the jaws' underside front to rear (rows 990 to 1770 for the traced side outline's 1.546 in) gives 504. Read by its face down columns 855 to 865: rows 993 to 1173 (180 px)
From the base's rear end forward. Behind the closed lever from the side; Primary Arms' photo, with the lever swung open, has it in the open, with the screw in its face.
The lever's catch block: how far it stands out of the base's left wall0.085 in ± 0.02 in 2.2 mmProvisionalPhoto: Holosun EU's gallery: the magnifier on its mount from below, the objective end down, 2200 px
Photo 0.085 in ± 0.02 in used
Holosun EU's gallery: the magnifier on its mount from below, the objective end down, 2200 px, harvested
Scale: the rail channel's roof in the same photo, columns 985 to 1310 (325 px) for the 0.653 in the drawing's traced end outline has between its two edges: 498 px/in; the jaws' underside front to rear (rows 990 to 1770 for the traced side outline's 1.546 in) gives 504. Read by its outer face at column 800 along row 1100, and the base's side at column 839 (the front block's face): 39 to 42 px; the lever's arm lies against it
The recess in the lever's outer face (the lever lock's screw is in it): its length along the lever0.32 in ± 0.015 in 8.1 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.32 in ± 0.015 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25. Read by its two ends at columns 622.5 and 691 along row 1242 (68.5 px): from 0.347 to 0.667 behind the mount's middle
The manual's Figure 5: "Press the lever lock forward and release the QD lever". How deep the recess is isn't read.
The recess in the lever's outer face: its height0.173 in ± 0.012 in 4.4 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.173 in ± 0.012 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the rail top at row 1247.19. Read by rows 1224.5 to 1261.5 down column 640 (37 px), its middle at row 1243: 0.02 in above the rail top, the roller's own middle
The recess in the lever's outer face: its middle, behind the mount's middle0.507 in ± 0.012 in 12.9 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.507 in ± 0.012 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25. Read by midway between its ends at columns 622.5 and 691 (656.75)
The socket screw in the lever's recess: its head, across0.15 in ± 0.02 in 3.8 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.15 in ± 0.02 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25. Read by its outer circle crosses column 660 at rows 1227 and 1259 (32 px); its middle at column 665, 0.545 in behind the mount's middle (0.038 behind the recess's)
A bright socket head in Holosun's picture of the left side, toward the recess's rear end.
The socket screw in the lever's recess: its middle, behind the mount's middle0.545 in ± 0.015 in 13.8 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.545 in ± 0.015 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25. Read by its circles' middle at column 665 along row 1242 (the outer one from 645 to 684.5), level with the recess's middle
The slotted link ahead of the lever's ears: its middle, ahead of the mount's middle0.38 in ± 0.015 in 9.7 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.38 in ± 0.015 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25. Read by its two sides at columns 457 and 477 along rows 1242 and 1270 (467)
An upright strip with a slot down it, in the base's side ahead of the lever (a spring shows in the slot's foot in the drawing). How thick it is isn't read.
The slotted link: its width along the rail0.093 in ± 0.012 in 2.4 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.093 in ± 0.012 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the mount's middle at column 548.25. Read by columns 457 to 477 (20 px); the slot in it columns 465 to 472.5 (0.035 in, a little over a third of it), from row 1222 to 1280
The slotted link: its height0.332 in ± 0.015 in 8.4 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.332 in ± 0.015 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (214.1 px/in, rms 0.003 in: the trace's), the rail top at row 1247.19. Read by rows 1212 to 1283 down column 475 (71 px): from 0.164 above the rail top to 0.167 below it, its middle level with the rail top
The clamp's nose between the base's left wall and the lever's roller: its width along the rail where it meets the wall0.445 in ± 0.03 in 11.3 mmProvisionalPhoto: Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px
Photo 0.445 in ± 0.03 in used
Holosun EU's gallery, file 'hm3x mount_1.JPG': the flip mount alone from above, its hinge at the right, 2200 px, harvested
Scale: the hinge block's length in the same photo (1208 px), 1.728 in by the side view: 699 px/in; by the mount's width in the drawing's end view (1.53 in from the lever's outer edge to the knuckle's outer face, 1097 px) it is 717 px/in, and the ± covers both. Read by along the base's left edge, column 745: rows 925 to 1240 (315 px)
The moving jaw's wedge, which the lever's ears bear on: it narrows from the wall to the roller (to 0.2 in: rows 1010 to 1150 at column 640). As tall as the roller where the drawing's side view shows it beside the roller (columns 549.5 to 567.5, rows 1230 to 1255).
The strip let into the mount base's top under the flip plate: its two screws, apart along the rail0.79 in ± 0.05 in 20.1 mmProvisionalPhoto: Holosun's HM3X manual V2.2, page 1, Figure 4: the mount from the front left and above, the flip plate standing; vector art, read at 900 dpi
Photo 0.79 in ± 0.05 in used
Holosun's HM3X manual V2.2, page 1, Figure 4: the mount from the front left and above, the flip plate standing; vector art, read at 900 dpi, harvested
Scale: the flip plate's own two screw holes in the same figure, 146.8 px apart along the same direction, for holosun-hm3x.flip_plate_screw_spacing (0.69 in). Read by the two screws' middles 168.3 px apart, parallel to the holes within a degree. Figure 3 has them 0.435 of the base's top face's left edge apart: 0.75 in by holosun-hm3x.base_plate_length
The manual's Figures 3 and 4 draw it in the base's top face between the knuckles, a bar with a screw at each end in a shallow pocket; what it does isn't said (it lies where a detent for the flip plate would). No photo on file shows the base's top with the plate swung off it.
The strip in the mount base's top: its length along the rail1 in ± 0.07 in 25.4 mmProvisionalPhoto: Holosun's HM3X manual V2.2, page 1, Figure 3: the mount from the rear left and above, the magnifier swung aside; vector art, read at 900 dpi
Photo 1 in ± 0.07 in used
Holosun's HM3X manual V2.2, page 1, Figure 3: the mount from the rear left and above, the magnifier swung aside; vector art, read at 900 dpi, harvested
Scale: the strip's own two screws in the same figure, 201.8 px apart, for holosun-hm3x.base_strip_screw_spacing. Read by the pocket's long side 254.6 px, a screw head's half width past each screw: 1.26 of their spacing. Its near end is at the rear knuckle's front face
The strip in the mount base's top: its width across the rail0.16 in ± 0.04 in 4.1 mmProvisionalPhoto: Holosun's HM3X manual V2.2, page 1, Figure 3: the mount from the rear left and above, the magnifier swung aside; vector art, read at 900 dpi
Photo 0.16 in ± 0.04 in used
Holosun's HM3X manual V2.2, page 1, Figure 3: the mount from the rear left and above, the magnifier swung aside; vector art, read at 900 dpi, harvested
Scale: the base's top face across the rail in the same figure, 561 px along its rear edge from its left edge to the knuckles' inner face, for the 0.778 in between the drawing's end view's left edge (0.563) and holosun-hm3x.hinge_knuckle_inner_right_of_centre: 721 px/in across. Read by the bar the two screws are in, 115 px across the rail
The strip in the mount base's top: its middle, right of the optical axis's vertical0.045 in ± 0.06 in 1.1 mmProvisionalPhoto: Holosun's HM3X manual V2.2, page 1, Figure 3: the mount from the rear left and above, the magnifier swung aside; vector art, read at 900 dpi
Photo 0.045 in ± 0.06 in used
Holosun's HM3X manual V2.2, page 1, Figure 3: the mount from the rear left and above, the magnifier swung aside; vector art, read at 900 dpi, harvested
Scale: the base's top face across the rail in the same figure, 561 px along its rear edge from its left edge to the knuckles' inner face, for the 0.778 in between the drawing's end view's left edge (0.563) and holosun-hm3x.hinge_knuckle_inner_right_of_centre: 721 px/in across. Read by the bar's left edge, carried along the rail's direction to the top face's rear edge, meets it 381 px from its left end (0.035 in left of the middle); the bar is 115 px wide
On the rail's middle line within the reading: under the flip plate's own two screws.
The tension screw's slot (in the hinge's rear end), across0.064 in ± 0.015 in 1.6 mmProvisionalPhoto: Holosun's HM3X manual V2.2, page 1, Figure 3: the mount from the rear left and above, the magnifier swung aside; vector art, read at 900 dpi
Photo 0.064 in ± 0.015 in used
Holosun's HM3X manual V2.2, page 1, Figure 3: the mount from the rear left and above, the magnifier swung aside; vector art, read at 900 dpi, harvested
Scale: the slotted head's own circle in the same figure, 285 px upright, for holosun-hm3x.hinge_barrel_d (0.35 in: the head is as wide as the barrel in Holosun's picture of the right side). Read by the slot's two edges 52 px apart at the circle's middle: 0.18 of the head
The manual's Figure 1 names the slotted head the tension screw; its Figures 3, 5 and 7 draw the slot level, across the rifle. How deep it is isn't read.
The two adjusters' caps (on top of the housing and on its right flank), across0.63 in ± 0.01 in 16 mmProvisionalPhoto: Holosun's dimensioned drawing, end view, seen from the objective end
Photo 0.63 in ± 0.01 in used
Holosun's dimensioned drawing, end view, seen from the objective end, harvested
Scale: the end view's frame on its own dimension lines (214.7 px/in: the axis at row 944.5, the rail top at 1247.19 for holosun-hm3x.optical_axis_above_rail_no_spacer; the axis's vertical at column 1612.3). Read by the top lug's two sides at columns 1544.5 and 1680 on rows 780 to 795 (135.5 px); the side lug's two ends at rows 877 and 1012 down column 1446 (135 px, its middle on the axis's row). The side view has the top cap's face 138 px long on row 777 (columns 574 to 712: 0.646 in with its corners' breaks)
The drawing's end view has two lugs of one size on the housing, one on top and one on the rifle's right, each as far from the axis as the other: the two adjusters' round caps (Holosun's pictures of the right side and from either end have both, each with a coin slot). Holosun's picture of the right side has the flank's cap 140 px across its rim where the housing is 872 px long (0.647 in: it is on the near flank and reads a little large).
The right flank's adjuster cap: its face, right of the optical axis0.786 in ± 0.01 in 20 mmProvisionalPhoto: Holosun's dimensioned drawing, end view, seen from the objective end: the picture's left is the rifle's right
Photo 0.786 in ± 0.01 in used
Holosun's dimensioned drawing, end view, seen from the objective end: the picture's left is the rifle's right, harvested
Scale: the end view's frame on its own dimension lines (214.7 px/in), the axis's vertical at column 1612.3. Read by the lug's outer face, a line at columns 1443 to 1446 on rows 920 to 970 (its outer edge 1443.5): 168.8 px from the axis
As far from the axis as the top cap's face is above it (holosun-hm3x.top_above_rail_no_spacer less the axis's height: 0.79).
The right flank's adjuster cap: its middle, ahead of the top cap's along the housing0.01 in ± 0.02 in 0.3 mmProvisionalPhoto: holosun.com 01: the right side, 1000 px, taken from about 14 degrees above: the top cap's face shows as an ellipse
Photo 0.01 in ± 0.02 in used
holosun.com 01: the right side, 1000 px, taken from about 14 degrees above: the top cap's face shows as an ellipse, harvested
Scale: holosun-hm3x.length (4.03 in) across the same picture, columns 63 to 935 on rows 440 to 460: 216.4 px/in along the housing, which the camera's height doesn't change. Read by along row 497 the flank's cap has its rim at columns 534 and 674, the black groove inside it at 551.5 and 659 and its inner cap's edge at 566.5 and 642.5: its middle 604.6. The top cap's face is columns 534 to 666 on row 282: its middle 600. 4.6 px is 0.021 in, less 0.007 to 0.013 for the flank's cap standing 0.79 in nearer a lens 30 to 60 in away and 105 px off the picture's middle
The two caps are in one plane across the housing, within the reading.
An adjuster cap's coin slot, along0.22 in ± 0.02 in 5.6 mmProvisionalPhoto: holosun.com 01: the right side, 1000 px, from about 14 degrees above
Photo 0.22 in ± 0.02 in used
holosun.com 01: the right side, 1000 px, from about 14 degrees above, harvested
Scale: the flank's cap's own rim in its plane, 140 px across on row 497, for holosun-hm3x.adjuster_cap_d. Read by the slot's dark run down column 605, rows 476 to 522 (47 px upright, which the camera's height shortens by 3%)
Each cap has one, turned however its adjuster stands: drawn along the housing on the top cap and upright on the flank's, as Holosun's picture of the right side has them within 15 degrees. How deep it is isn't read.
An adjuster cap's coin slot, across0.06 in ± 0.015 in 1.5 mmProvisionalPhoto: holosun.com 01: the right side, 1000 px, from about 14 degrees above
Photo 0.06 in ± 0.015 in used
holosun.com 01: the right side, 1000 px, from about 14 degrees above, harvested
Scale: the flank's cap's own rim in its plane, 140 px across on row 497, for holosun-hm3x.adjuster_cap_d. Read by the slot's dark pill is 13 px across square to its length (it leans 15 degrees in the picture: columns 590 to 611 where row 497 crosses it aslant)
The HOLOSUN oval on the left flank: its length along the housing1.239 in ± 0.015 in 31.5 mmProvisionalPhoto: Holosun's dimensioned drawing, side view: the left side
Photo 1.239 in ± 0.015 in used
Holosun's dimensioned drawing, side view: the left side, harvested
Scale: the side view's frame on its own dimension lines (213.5 px/in along: the base's two extension lines at columns 342.19 and 754.31 for holosun-hm3x.mount_base_length). Read by the oval's outer line along row 944: columns 515 and 779.5 (264.5 px)
A rounded-ended oval with the maker's name in it (the letters aren't drawn). Primary Arms' photo of the left side has it 600 px long inside its rim at 479 px/in (1.25 in, on the near flank).
The HOLOSUN oval on the left flank: its height0.31 in ± 0.015 in 7.9 mmProvisionalPhoto: Holosun's dimensioned drawing, side view: the left side
Photo 0.31 in ± 0.015 in used
Holosun's dimensioned drawing, side view: the left side, harvested
Scale: the drawing's frame on its own dimension lines (214.7 px/in upright), the axis at row 944.5. Read by the oval's outer line down columns 560, 648 and 740: rows 911 and 977 (66 px: 0.307 in). The end view has the same thing edge on over rows 910.7 to 978.3 (0.315 in)
Its middle is on the optical axis's row in both of the drawing's views.
The HOLOSUN oval on the left flank: its middle, behind the top cap's along the housing0.02 in ± 0.015 in 0.5 mmProvisionalPhoto: Holosun's dimensioned drawing, side view: the left side, the objective at the picture's left
Photo 0.02 in ± 0.015 in used
Holosun's dimensioned drawing, side view: the left side, the objective at the picture's left, harvested
Scale: the side view's frame on its own dimension lines (213.5 px/in along). Read by the oval's middle at column 647.25 (its ends 515 and 779.5), the top cap's face's at 643 (columns 574 to 712 on row 777): 4.25 px toward the eyepiece
Under the top cap, within the reading. Holosun's picture of the left side (5ee8dd2e6815, 208.7 px/in: the housing is columns 94 to 935) has the oval's ends at columns 286 and 545 (1.241 in long, middle 415.5) and the top cap's face at 351 to 481 (middle 416): the two middles within 0.01 in once the near flank's 2% is allowed for.
The HOLOSUN oval on the left flank: how far its face stands from the optical axis0.739 in ± 0.01 in 18.8 mmProvisionalPhoto: Holosun's dimensioned drawing, end view, seen from the objective end: the picture's right is the rifle's left
Photo 0.739 in ± 0.01 in used
Holosun's dimensioned drawing, end view, seen from the objective end: the picture's right is the rifle's left, harvested
Scale: the end view's frame on its own dimension lines (214.7 px/in), the axis's vertical at column 1612.3. Read by the bump's outer edge at column 1771 on rows 921 to 968 (column 1770 is dark over those rows, 1772 white): 158.7 px from the axis; its ends at rows 910.7 and 978.3
The relief read where it meets an edge: the drawing's end view has, on the rifle's left at the axis's height and over the oval's own height, a flat-faced bump standing past the housing's round (the round's widest is 0.72 to 0.73 in from the axis by the side view's top edge either side of the top boss). The photos have the oval's field sunk inside its edge (a shaded band inside the edge all round, a lit line outside it: Primary Arms' photo of the left side, Holosun's of the right): read together, a raised oval rim round a field at about the housing's own surface. That the two are one thing is this reading, not a view of it.
The HOLOSUN oval: the width of the rim round its sunk field0.02 in ± 0.008 in 0.5 mmProvisionalPhoto: Primary Arms: the left side, 2200 px
Photo 0.02 in ± 0.008 in used
Primary Arms: the left side, 2200 px, harvested
Scale: 479 px/in, the scale the photo's rings were read at (holosun-hm3x.objective_ring_od across rows 194.5 to 826), 2% large on the near flank. Read by the shaded band inside the oval's edge: rows 460 to 473 down columns 750, 850 and 950 at its top (13 px), columns 545 to 551 along row 530 at its left end (6 px), each with a lit line 4 to 6 px outside it: 0.013 to 0.027 in
How far the field is sunk inside the rim isn't read: drawn down to the housing's own round at the oval's middle.
The HOLOSUN oval on the right flank: its length along the housing1 in ± 0.03 in 25.4 mmProvisionalPhoto: holosun.com 01: the right side, 1000 px, from about 14 degrees above
Photo 1 in ± 0.03 in used
holosun.com 01: the right side, 1000 px, from about 14 degrees above, harvested
Scale: holosun-hm3x.length (4.03 in) across the same picture, columns 63 to 935: 216.4 px/in along the housing at the axis's depth, up to 2% more on the near flank. Read by the oval's ends along row 495: the shaded line at column 252 and the lit one at 466 to 469 (216.7 px)
Smaller than the left flank's, and behind the adjuster's cap, toward the eyepiece. Whether it stands off the housing as the left one does isn't seen (the drawing's end view has the cap in front of it): drawn standing as far off the housing's round as the left one.
The HOLOSUN oval on the right flank: its height0.245 in ± 0.02 in 6.2 mmProvisionalPhoto: holosun.com 01: the right side, 1000 px, from about 14 degrees above
Photo 0.245 in ± 0.02 in used
holosun.com 01: the right side, 1000 px, from about 14 degrees above, harvested
Scale: 216.4 px/in (holosun-hm3x.length across the same picture), the flank at the axis's height turned 14 degrees from the camera. Read by the oval's edges down columns 300, 360 and 420: rows 468 to 470 and 517 to 520 (50 px, 0.23 in as seen; 3% more square on, and the same shape as the left flank's oval, 4.0 to 1, would be 0.25)
The HOLOSUN oval on the right flank: its middle, behind the adjuster cap's along the housing1.12 in ± 0.03 in 28.4 mmProvisionalPhoto: holosun.com 01: the right side, 1000 px, from about 14 degrees above
Photo 1.12 in ± 0.03 in used
holosun.com 01: the right side, 1000 px, from about 14 degrees above, harvested
Scale: 216.4 px/in (holosun-hm3x.length across the same picture), up to 2% more on the near flank, where both are. Read by the oval's middle at column 360.5 (its ends 252 and 469), the cap's at 604.6: 244.1 px, 1.128 in at the axis's scale and 1.11 at the flank's
The slanted pockets in each side of the magnifier's foot5ProvisionalPhoto: Holosun's dimensioned drawing, side view: the left side, the objective at the picture's left
Photo 5 count used
Holosun's dimensioned drawing, side view: the left side, the objective at the picture's left, harvested
Scale: none needed: a count. Read by along row 1100 the pockets' walls are at columns 437 and 464.5, 479 and 506.5, 521.5 and 549, 564 and 590.5, and the fifth's front wall at 608 with the foot's rear wall at 625 behind it
Four whole ones and a fifth, rearmost, cut short by the foot's rear end (foot_rib_rear_wall_behind_base_centre). On both sides: Holosun's picture of the right side (eea64f6b7ff8) has five between the housing and the hinge's barrel, the four whole ones' dark walls at columns 781.5, 739, 697 and 655.5 on row 611 of a picture at 216.4 px/in (42 px apart: 0.194 in) and a short one behind them at columns 624 to 635, leaning the same way (tops toward the objective); so has Primary Arms' photo of the left side (7602cbc9ffbd: four and a short fifth). Sunk, not raised: in the right side's picture, lit from the left, each has a dark wall at its left and a lit one at its right, where the flank's cap, which stands out, is lit at its left; Primary Arms' photo, lit from above, has each one's upper edge dark and its lower corner lit.
The foot's slanted pockets: from one to the next along the housing0.198 in ± 0.01 in 5 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.198 in ± 0.01 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (213.5 px/in along). Read by the four front walls along row 1100 at columns 437, 479, 521.5 and 564: 42, 42.5 and 42.5 px apart (42.3)
The foot's slanted pockets: each one's width along the housing (wall to wall along a level line)0.128 in ± 0.012 in 3.3 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.128 in ± 0.012 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (213.5 px/in along). Read by between the middles of each pocket's two drawn walls along row 1100: 27.5, 27.5, 27.5 and 26.5 px (the lines are 3 to 4 px thick: ± covers which edge of a line is the wall)
The foot's slanted pockets: how far their walls lean from upright, their tops toward the objective30° ± 3°ProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 30 deg ± 3 deg used
Holosun's dimensioned drawing, side view, harvested
Scale: the drawing's own rows and columns (214.7 px/in upright, 213.5 along). Read by the first pocket's front wall is at columns 432 to 435 on row 1094 and 449 to 453 on row 1124: 17.5 px along in 30 rows (30.2 degrees); the others run parallel to it (rows 1094 to 1124 of each)
The foot's slanted pockets: the first one's front wall at the pockets' bottom line, ahead of the mount base's centre0.438 in ± 0.012 in 11.1 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.438 in ± 0.012 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (213.5 px/in along), the base's front extension line at column 342.19 for half of holosun-hm3x.mount_base_length. Read by the wall's line (column 437 on row 1100, leaning 0.583 px a row) carried down to the bottom line, row 1130.5: column 454.8, 112.6 px behind the base's front
The first is the one nearest the objective; the others follow it rearward at foot_rib_pitch.
The foot's slanted pockets: their bottom line above the foot's underside (the face the spacer goes in at)0.104 in ± 0.01 in 2.6 mmProvisionalPhoto: Holosun's dimensioned drawing, side view; it has no spacer
Photo 0.104 in ± 0.01 in used
Holosun's dimensioned drawing, side view; it has no spacer, harvested
Scale: the drawing's frame on its own dimension lines (214.7 px/in upright), the interface's line at row 1152.84. Read by all four pockets' lower ends are on row 1130 to 1131 (the dark runs along row 1130 between columns 454 and 603): 22.3 px above the interface
The foot's slanted pockets: their top line above the foot's underside, over the first pocket's front wall's foot0.31 in ± 0.01 in 7.9 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.31 in ± 0.01 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the drawing's frame on its own dimension lines (214.7 px/in upright), the interface's line at row 1152.84. Read by the pockets' upper edges down columns 445 to 448, 487 to 490, 530 to 533, 573 to 576 and 618 to 621: rows 1085.5, 1089, 1092, 1096 and 1099.5, one line falling 0.081 px a column; at column 454.8 it is at row 1086.3, 66.6 px above the interface. The housing's lower line is 12.5 to 13 px above it at each
The tops aren't level: they follow the housing's underside, a sixteenth of an inch under it, and fall toward the eyepiece (foot_rib_top_fall).
The foot's slanted pockets: how far their top line falls toward the eyepiece, as an angle from level4.7° ± 1°ProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 4.7 deg ± 1 deg used
Holosun's dimensioned drawing, side view, harvested
Scale: the drawing's own rows and columns. Read by the five upper edges (rows 1085.5, 1089, 1092, 1096, 1099.5 at columns 446.5, 488.5, 531.5, 574.5, 619.5): 14 rows in 173 columns
The foot's slanted pockets: the upright wall that cuts the fifth one short, behind the mount base's centre0.359 in ± 0.012 in 9.1 mmProvisionalPhoto: Holosun's dimensioned drawing, side view
Photo 0.359 in ± 0.012 in used
Holosun's dimensioned drawing, side view, harvested
Scale: the side view's frame on its own dimension lines (213.5 px/in along), the base's front extension line at column 342.19. Read by the upright line at columns 624 to 626 on rows 1100 to 1124, behind the fifth pocket's leaning front wall (column 608 on row 1100, 618 on row 1124): 282.8 px behind the base's front
How far the shallow pieces no view shows in profile are sunk (the foot's slanted pockets)0.02 in ± 0.01 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the least the page draws (docs/research/model-detail-pass-2026-10-12.md), as holosun-aro.detail_relief is. That the pockets are sunk is read (foot_rib_count); how deep isn't seen in any view on file.
Worked out 0.02 in ± 0.01 in used
An assumption for the drawing, not a reading: the least the page draws (docs/research/model-detail-pass-2026-10-12.md), as holosun-aro.detail_relief is. That the pockets are sunk is read (foot_rib_count); how deep isn't seen in any view on file., harvested
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Picatinny rail (MIL-STD-1913)
- Uppers
- Aero Precision M4E1 Enhanced Upper Receiver Stripped, Aero Precision M4E1 Threaded upper receiver, BCM M4 Upper Receiver Assembly (w/ Laser T-Markings), Expo Arms 7075 Stripped AR-15 Upper Receiver, Geissele Automatics Super Duty Stripped Upper Receiver, Nordic Components 22RB .22 LR upper, 16", Palmetto State Armory AR-15 Stripped Upper Receiver, Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12", Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16"
- Handguards
- Aero Precision AR15 10.3" R-ONE M-LOK handguard, Aero Precision AR15 12.7" R-ONE M-LOK handguard, Aero Precision AR15 15" Enhanced M-LOK Handguard, Gen 2, Aero Precision AR15 15" R-ONE M-LOK handguard, Aero Precision AR15 15" S-ONE M-LOK Handguard, Aero Precision AR15 16.6" R-ONE M-LOK handguard, Aero Precision AR15 7.3" R-ONE M-LOK handguard, Aero Precision AR15 9.3" R-ONE M-LOK handguard, BCM MCMR-10 (M-LOK® Compatible* Modular Rail), BCM MCMR-13 (M-LOK® Compatible* Modular Rail), BCM MCMR-15 (M-LOK® Compatible* Modular Rail), Expo Arms Free Float AR-15 Handguard - M-LOK - 15", Geissele Automatics 10.5" Super Modular Rail MK16 M-LOK, Geissele Automatics 13.5" Super Modular Rail MK16 M-LOK, Geissele Automatics 15" Super Modular Rail MK16 M-LOK, MAS Defense 12.62" NERO M-LOK FREE FLOAT, MAS Defense 15" NERO M-LOK FREE FLOAT, MAS Defense 9.87" NERO M-LOK FREE FLOAT, Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length), Midwest Industries Combat Rail One Piece Free Float Handguard, M-LOK™ (15")
- Frames
- Taurus TX22 Gen 2 frame
- Rail sections
- Magpul M-LOK® Aluminum Rail, 3 Slots, Magpul M-LOK® Aluminum Rail, 5 Slots, Magpul M-LOK® Aluminum Rail, 7 Slots, Magpul M-LOK® Aluminum Rail, 9 Slots, Magpul M-LOK® Polymer Rail, 11 Slots, Magpul M-LOK® Polymer Rail, 3 Slots, Magpul M-LOK® Polymer Rail, 5 Slots, Magpul M-LOK® Polymer Rail, 7 Slots, Magpul M-LOK® Polymer Rail, 9 Slots
Sight and magnifier
- Optics
- Aimpoint Duty RDS Red Dot Sight, Aimpoint Micro T-2 Red Dot Reflex Sight, Aimpoint Patrol Rifle Optic (PRO) Red Dot Reflex Sight - QRP2 Mount, EOTECH HWS EXPS3 holographic weapon sight, 1-Dot Speed Ring, Holosun ARO 2 MOA red dot (listed by Holosun as ARO-CORE-RD-2), Holosun EPS Carry enclosed pistol sight, 2 MOA red dot (EPS-CARRY-RD-2), Holosun HS510C Open Reflex MRS Solar QD Mount, SIG Sauer ROMEO-MSR GEN II red dot sight, 2 MOA red dot, SIG Sauer ROMEO5 GEN II 1x20mm Compact Illuminated Dot Sight, 2 MOA red dot
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Holosun $235.28 Nov 21, 2026, in stock that day