Scope mount
Primary Arms Deluxe AR-15 Scope Mount - 30mm
Primary Arms' one-piece cantilever scope mount for a 30 mm tube: "ideal for M4, AR-15, and similar “flat-top” 1913 Picatinny mounting platforms", "Places the center of your 30mm tube scope 1.5 inches above the rail", with "2.52 inches of clearance between the rings". Two cross bolts with slotted nuts clamp it; the scope slides in its two rings before their caps are tightened, which sets the eye relief. The mount Primary Arms sells its SLx 1-6x24 in.

- Weight
- 8.2 oz Conflictpublished: Primary Arms, Deluxe AR-15 Scope Mount - 30mm (PADLXSM), product page, the maker, read Oct 13, 2026Its sources span 6.97 oz to 8.25 oz.
- Lowest price
- $59.99 at Primary Arms, read Nov 21, 2026 (Black)
- Maker's number
- PADLXSM
- Colour
- Black (placeholder)
- Drawn as
- modelled
- Maker's page
- primaryarms.com
In “Aero 16 in, slick rail and a 1-6x”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Ring axis above the rail's top1.5 in ± 0.05 in 38.1 mmConfirmedPublished: Primary Arms, Deluxe AR-15 Scope Mount - 30mm (PADLXSM), product page, the maker, read Oct 13, 2026
Published “Places the center of your 30mm tube scope 1.5 inches above the rail.” used
Primary Arms, Deluxe AR-15 Scope Mount - 30mm (PADLXSM), product page, the maker, read Oct 13, 2026 the page, harvested Oct 13, 2026
Published “Central Height: 1.50”
KYGUNCO, PRIMARY ARMS Deluxe AR-15 Scope Mount 30mm (PRM-910058), a seller, read Oct 13, 2026 the page, harvested Oct 13, 2026
Published “The integrated riser places the center of the tube 1.5”/38mm above the rail.”
Armamat, Primary Arms Deluxe Scope Mount - 30mm (manufacturer number PADLXSM), a seller, read Oct 13, 2026 the page, harvested Oct 13, 2026
Published “It places the center of the scope exactly 1.5 inches above the rail,”
The Truth About Guns, Gear Review: Primary Arms Deluxe AR15 Scope Mount (March 31, 2012; the reviewer's own unit), a review, read Oct 13, 2026 the page, harvested Oct 13, 2026
The maker's own sentence; two sellers and a reviewer say the same.
Tube diameter the rings are bored for1.181 in 30 mmConfirmedPublished: Primary Arms, Deluxe AR-15 Scope Mount - 30mm (PADLXSM), product page, the maker, read Oct 13, 2026
Published “Fits scopes with 30mm tubes.” used
Primary Arms, Deluxe AR-15 Scope Mount - 30mm (PADLXSM), product page, the maker, read Oct 13, 2026 the page, harvested Oct 13, 2026
Its table: "Mount Compatibility 30mm". The 1 in mount is another number (PADLXSM1), not read.
Published “The optic mount is made of a Picatinny base with two 30mm scope rings with a 2.52”/64mm spread.”
Armamat, Primary Arms Deluxe Scope Mount - 30mm (manufacturer number PADLXSM), a seller, read Oct 13, 2026 the page, harvested Oct 13, 2026
The maker's own sentence; a seller says the same.
Between the two rings, face to face2.52 in 64 mmConflictPublished: Primary Arms, Deluxe AR-15 Scope Mount - 30mm (PADLXSM), product page, the maker, read Oct 13, 2026
Published “2.52 inches of clearance between the rings.” used
Primary Arms, Deluxe AR-15 Scope Mount - 30mm (PADLXSM), product page, the maker, read Oct 13, 2026 the page, harvested Oct 13, 2026
Published “The optic mount is made of a Picatinny base with two 30mm scope rings with a 2.52”/64mm spread.”
Armamat, Primary Arms Deluxe Scope Mount - 30mm (manufacturer number PADLXSM), a seller, read Oct 13, 2026 the page, harvested Oct 13, 2026
Published “The Primary Arms mount is 5.2 inches long overall, and there’s 2.5 inches of clearance between the front and rear rings.”
The Truth About Guns, Gear Review: Primary Arms Deluxe AR15 Scope Mount (March 31, 2012; the reviewer's own unit), a review, read Oct 13, 2026 the page, harvested Oct 13, 2026
Photo 2.572 in ± 0.03 in
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the rings' near side flats' inner ends, columns 352.7 and 1185.2 (level 128), at the near flats' scale: flat to flat. Each flat ends at its edge's break, short of the face
The maker's figure, face to face. The photo reads the flats 0.05 in further apart, which is their edges' breaks: taken so (ring_edge_break).
page and left differ by 0.052 in beyond what each states it is good to.
armamat and left differ by 0.052 in beyond what each states it is good to.
Rings, the break on the edge between an end face and a side flat0.026 in ± 0.012 in 0.7 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 0.026 in ± 0.012 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by worked out, not read as an edge: half of what the near flats stand further apart (2.572 in, ring_clearance's photo reading) than the maker's 2.52 between the rings. The picture has a lit line 8 px wide down each of those edges
Each ring's length along the tube (face to face)0.693 in ± 0.02 in 17.6 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 0.693 in ± 0.02 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by each ring's near side flat, 207.2 px (columns 145.5 to 352.7) and 207.3 px (1185.2 to 1392.5) at rows 500 to 600: 0.641 in at the near flats' scale, and an edge break at each end (ring_edge_break, twice)
Rear ring, its middle ahead of the rear cross bolt1.435 in ± 0.03 in 36.4 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 1.435 in ± 0.03 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the rear ring's near side flat, columns 1185.2 to 1392.5: its middle, 0.624 in from the lens's axis at the near flats' scale; the rear cross bolt's stud end (the right-hand nut's middle, column 1770) is 2.059 in from the axis at the scale of where it stands. The ± is the nut's place out from the mid-plane (1.1 to 1.3 in) and the pick of the stud's middle
Front ring, its middle ahead of the rear cross bolt4.65 in ± 0.03 in 118.1 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 4.65 in ± 0.03 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the front ring's near side flat, columns 145.5 to 352.7: its middle (as ring_rear_x). The two middles are 3.215 in apart: the maker's 2.52 between the rings and one ring's length (0.693) make 3.213
Overall length, the base's rear end to the front ring's front face5.394 in 137 mmConflictPublished: Armamat, Primary Arms Deluxe Scope Mount - 30mm (manufacturer number PADLXSM), a seller, read Oct 13, 2026
Published “Length: 13.7 cm” used
Armamat, Primary Arms Deluxe Scope Mount - 30mm (manufacturer number PADLXSM), a seller, read Oct 13, 2026 the page, harvested Oct 13, 2026
5.39 in. The shop's own table ("Packaging Dimensions & Weight", with the packed sizes given apart); whose measuring it is the page doesn't say.
Published “The Primary Arms mount is 5.2 inches long overall, and there’s 2.5 inches of clearance between the front and rear rings.”
The Truth About Guns, Gear Review: Primary Arms Deluxe AR15 Scope Mount (March 31, 2012; the reviewer's own unit), a review, read Oct 13, 2026 the page, harvested Oct 13, 2026
A 2012 unit, the reviewer's own measuring. The same sentence rounds the maker's 2.52 to 2.5.
Photo 5.39 in ± 0.05 in
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the front ring's front face (its near flat's front end, column 145.5, and an edge break) to the clamp bar's rear end (column 1881), each at the scale of where it stands
A shop's stated length, and the photo read through its own camera comes to the same 5.39 in without having been set by it. The 2012 review's 5.2 is 0.2 short of both: kept, a visible conflict (an older unit, or a quick rule).
armamat and review differ by 0.194 in beyond what each states it is good to.
review and left differ by 0.19 in beyond what each states it is good to.
Overall width (across the nuts and the bolts' heads)1.969 in 50 mmProvisionalPublished: Armamat, Primary Arms Deluxe Scope Mount - 30mm (manufacturer number PADLXSM), a seller, read Oct 13, 2026
Published “Width: 5 cm” used
Armamat, Primary Arms Deluxe Scope Mount - 30mm (manufacturer number PADLXSM), a seller, read Oct 13, 2026 the page, harvested Oct 13, 2026
1.97 in, a whole number of centimetres. As modelled the nuts' ends are 1.12 in left of the middle and the rings' flats 0.79 right: 1.91.
Overall height2.559 in 65 mmProvisionalPublished: Armamat, Primary Arms Deluxe Scope Mount - 30mm (manufacturer number PADLXSM), a seller, read Oct 13, 2026
Published “Height: 6.5 cm” used
Armamat, Primary Arms Deluxe Scope Mount - 30mm (manufacturer number PADLXSM), a seller, read Oct 13, 2026 the page, harvested Oct 13, 2026
2.56 in, to half a centimetre. As modelled, from the nuts' lowest corners (0.29 under the rail's top) to the caps' tops (2.15 over it): 2.44.
Rings, across their side flats1.585 in ± 0.05 in 40.3 mmProvisionalPhoto: Armamat 113267060_3.jpg, the mount alone from the front left and above, the front ring's front face toward the lens, 4200 x 2940
Photo 1.585 in ± 0.05 in used
Armamat 113267060_3.jpg, the mount alone from the front left and above, the front ring's front face toward the lens, 4200 x 2940, harvested
Scale: the front ring's front face in its own plane (a long lens: the background is out of focus): along the split between the cap and the lower half, 940 px/in by the 30 mm bore's chord there (1073.5 px from rim to rim; the split is 0.15 in above the bore's centre, so the chord is 1.142 in); up the face 801 px/in, by the lower half's side flat (463 px, the mean of its two edges, for the 0.578 in the left side view reads). Read by the face's two upright edges along the split, (466, 1594) and (1940, 1814): 1490 px. The bore stands 204 and 210 px inside them
No view is square across the mount. Read on the front ring's front face in a long-lens oblique, in that face's own plane, by the bore's chord along the split. The left side view's band for the same face (67 px against the bore's 45) would make it 1.76: a band 67 px wide can't tell.
Rings, the split between cap and lower half above the bore's centre0.15 in ± 0.04 in 3.8 mmCorroboratedPhoto: Armamat 113267060_3.jpg, the mount alone from the front left and above, the front ring's front face toward the lens, 4200 x 2940
Photo 0.15 in ± 0.04 in used
Armamat 113267060_3.jpg, the mount alone from the front left and above, the front ring's front face toward the lens, 4200 x 2940, harvested
Scale: the front ring's front face in its own plane (a long lens: the background is out of focus): along the split between the cap and the lower half, 940 px/in by the 30 mm bore's chord there (1073.5 px from rim to rim; the split is 0.15 in above the bore's centre, so the chord is 1.142 in); up the face 801 px/in, by the lower half's side flat (463 px, the mean of its two edges, for the 0.578 in the left side view reads). Read by the cap's bore is an arc that rises 354 px over a chord of 1073.5 px: a third of its chord, where a half ring's is a half. For a 30 mm circle that rise over that chord, with the face seen from 20 to 35 degrees above, puts the chord 0.14 to 0.20 in above the centre; the bore's top edge is 473 px (0.591 in up the face) above a centre 119 px under the split
Photo 0.13 in ± 0.05 in
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: the bore's opening on the front ring's rear face (rows 333 to 697: its centre at row 515, at the mid-plane) against the split on the near side flat (row 500), through the camera of ring_clearance's reading with the lens's height left to the base's own figures: with the lens above the picture (row -54) the cross bolts come out at the rail's top, where they must lie in its slots, and the split 0.13 in above the centre. Read by two heights at two depths in a photo taken from above: as good as the lens's height is
Read in one plane, the face's own, where the side view compares two depths from a lens whose height is itself inferred. They agree within either's ±.
The cap is less than a half ring: the lower half is a U whose walls stand straight up from the bore's centre to the split.
Rings, the cap's top above the bore's centre0.645 in ± 0.02 in 16.4 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 0.645 in ± 0.02 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the front cap's top edge (row 320.8) and the bore's top edge on the same ring's rear face (row 333, 14 px lower), both at the mid-plane: the cap is 0.045 in thick over the tube, 0.062 by the top's own height through the camera; between the two. The rear ring's top reads 10 px higher in the picture than the front's (a roll of half a degree)
Ring caps, the ledge the screws stand on above the split0.165 in ± 0.02 in 4.2 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 0.165 in ± 0.02 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the front cap's side flat, from the split (row 497 to 500) up to its upper edge (row 443, a lit line to 450: the ledge's top seen from above): 0.15 to 0.18 in at the near flats' scale. The rear cap's reads 0.115 in (rows 458 to 495), its lit line fainter
Rings, the side flat's lower end below the bore's centre0.437 in ± 0.03 in 11.1 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 0.437 in ± 0.03 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the front ring's side flat ends at row 690, 0.578 in under the split at the near flats' scale, where a lit facet begins; less the split's height above the centre (ring_split_above_axis)
Rings, the foot of the facet under each side flat below the bore's centre0.76 in ± 0.04 in 19.3 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 0.76 in ± 0.04 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the lit facet under the front ring's side flat, rows 690 to about 795 at column 250: 0.32 in of height at the near flats' scale; its lower edge is a change of tone, not a line
Under each side flat the ring narrows to the arm's width down a facet, lit in the left side view; on the front ring it runs on round the ring's front lower corner.
Ring cap screws, the head's diameter0.24 in ± 0.015 in 6.1 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 0.24 in ± 0.015 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the front cap's two near heads, 76 px each at their widest (columns 160 to 236 and 262 to 338), at the scale of where they stand (318 px/in)
Ring cap screws, the head's height above the ledge0.11 in ± 0.02 in 2.8 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 0.11 in ± 0.02 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the same two heads, rows 407 to 443: socket heads, their upper third tapered, standing on the ledge with no counterbore
Ring cap screws, the two on a side, centre to centre along the tube0.315 in ± 0.01 in 8 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 0.315 in ± 0.01 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the two heads' middles on each cap: columns 198 and 300 on the front ring, 1232 and 1335 on the rear (102 and 103 px), about the flat's own middle
Ring cap screws, their axes from the mount's mid-plane0.67 in ± 0.05 in 17 mmProvisionalPhoto: Armamat 113267060_3.jpg, the mount alone from the front left and above, the front ring's front face toward the lens, 4200 x 2940
Photo 0.67 in ± 0.05 in used
Armamat 113267060_3.jpg, the mount alone from the front left and above, the front ring's front face toward the lens, 4200 x 2940, harvested
Scale: the front ring's front face in its own plane (a long lens: the background is out of focus): along the split between the cap and the lower half, 940 px/in by the 30 mm bore's chord there (1073.5 px from rim to rim; the split is 0.15 in above the bore's centre, so the chord is 1.142 in); up the face 801 px/in, by the lower half's side flat (463 px, the mean of its two edges, for the 0.578 in the left side view reads). Read by not read as a place: each head stands on its ledge between the cap's arch and the side flat, touching neither's edge in this view or in the rear oblique (1286e081602a); the ledge runs from 0.55 in (where an arch of the cap's own radius meets it) to the flat at 0.79, and the head is 0.24 across. Its middle
The arm under the rings, across1.2 in ± 0.06 in 30.5 mmProvisionalPhoto: Armamat 113267060_4.jpg, the mount alone from the rear right and above, the base's rear end toward the lens, 4200 x 2940
Photo 1.2 in ± 0.06 in used
Armamat 113267060_4.jpg, the mount alone from the rear right and above, the base's rear end toward the lens, 4200 x 2940, harvested
Scale: the base's rear end face in its own plane: the channel between the clamp bar and the fixed jaw, 314 px wide at its roof on a gridded crop (0.65 px to the pixel), taken to be the rail's top it clamps (std.picatinny.top_width, 0.835 in, and a hundredth of clearance): 374 px/in. An assumed fit, not a published size. Read by twice the fixed side's right face from the channel's middle (base_right_z): the arm is drawn about the mount's mid-plane, its right face one with the base's as the view from below has it
The arm and the base's fixed side are one width in the view from below (d4df1c9eae33): the rings stand out past it each side.
Base, its fixed (right) side's face from the mount's mid-plane0.6 in ± 0.04 in 15.2 mmProvisionalPhoto: Armamat 113267060_4.jpg, the mount alone from the rear right and above, the base's rear end toward the lens, 4200 x 2940
Photo 0.6 in ± 0.04 in used
Armamat 113267060_4.jpg, the mount alone from the rear right and above, the base's rear end toward the lens, 4200 x 2940, harvested
Scale: the base's rear end face in its own plane: the channel between the clamp bar and the fixed jaw, 314 px wide at its roof on a gridded crop (0.65 px to the pixel), taken to be the rail's top it clamps (std.picatinny.top_width, 0.835 in, and a hundredth of clearance): 374 px/in. An assumed fit, not a published size. Read by the fixed jaw is 68 px thick at the channel's roof (0.18 in), outside the rail's half width
Clamp bar, its outer (left) face from the mount's mid-plane0.65 in ± 0.04 in 16.5 mmProvisionalPhoto: Armamat 113267060_4.jpg, the mount alone from the rear right and above, the base's rear end toward the lens, 4200 x 2940
Photo 0.65 in ± 0.04 in used
Armamat 113267060_4.jpg, the mount alone from the rear right and above, the base's rear end toward the lens, 4200 x 2940, harvested
Scale: the base's rear end face in its own plane: the channel between the clamp bar and the fixed jaw, 314 px wide at its roof on a gridded crop (0.65 px to the pixel), taken to be the rail's top it clamps (std.picatinny.top_width, 0.835 in, and a hundredth of clearance): 374 px/in. An assumed fit, not a published size. Read by the bar is 87 px thick at the channel's roof (0.23 in), outside the rail's half width; the whole clamp 472 px across its top (1.26 in)
Clamp bar, its thickness across the rifle0.23 in ± 0.03 in 5.8 mmProvisionalPhoto: Armamat 113267060_4.jpg, the mount alone from the rear right and above, the base's rear end toward the lens, 4200 x 2940
Photo 0.23 in ± 0.03 in used
Armamat 113267060_4.jpg, the mount alone from the rear right and above, the base's rear end toward the lens, 4200 x 2940, harvested
Scale: the base's rear end face in its own plane: the channel between the clamp bar and the fixed jaw, 314 px wide at its roof on a gridded crop (0.65 px to the pixel), taken to be the rail's top it clamps (std.picatinny.top_width, 0.835 in, and a hundredth of clearance): 374 px/in. An assumed fit, not a published size. Read by 87 px at the channel's roof, from its inner face to its outer
Base, the break on its top face's right edge0.12 in ± 0.03 in 3 mmProvisionalPhoto: Primary Arms PADLXSM_01.jpg, the mount alone on white, right side, 2000 x 1334
Photo 0.12 in ± 0.03 in used
Primary Arms PADLXSM_01.jpg, the mount alone on white, right side, 2000 x 1334, harvested
Scale: the rings' near side flats in this view, their inner ends 763.5 px apart for the 2.572 in the left view's camera reads (296.9 px/in), and the base's right face 0.19 in further from the lens (294 px/in); its two bolt heads are then 2.01 in apart (590 px) for five slots, 1.969. Read by the band under the top face's near edge, rows 915 to 950 at column 500, a shade darker than the top and lighter than the upright face under it: its height. How far in it reaches isn't read: drawn at 45 degrees
The right side view is taken from above as the left is: over this band the base's top face shows, lit, 55 px deep (rows 860 to 915), with the clamp bar's top beyond it.
Clamp cross bolts, centre to centre1.97 in 50 mmConfirmedWorked out: 5 * {std.picatinny.slot_pitch}
Worked out 1.97 in used
5 * {std.picatinny.slot_pitch}, harvested
Photo 1.99 in ± 0.03 in
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the two studs' ends in their nuts, columns 1117 and 1770 (653 px), 1.12 in nearer the lens than the mid-plane (the bar's outer face and the washer and nut on it); the right side view's two bolt heads read 2.01 (590 px at 294 px/in)
Both bolts lie in recoil slots, a whole number of pitches apart; the photos read 1.99 and 2.01, which is five and neither four nor six.
Each bolt crosses the channel as a bar in a rail slot (the view from below, d4df1c9eae33, has both): a whole number of slots apart.
Clamp cross bolts, their axis above the rail's top0 in ± 0.03 in 0 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 0 in ± 0.03 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the studs' ends, rows 1058 and 1063, through the camera with the rings' axis 1.5 in above the rail: -0.004 in. The right side view has the heads' middles 0.44 in under the base's top, -0.03 in
Clamp cross bolts, the head's diameter0.31 in ± 0.02 in 7.9 mmProvisionalPhoto: Primary Arms PADLXSM_01.jpg, the mount alone on white, right side, 2000 x 1334
Photo 0.31 in ± 0.02 in used
Primary Arms PADLXSM_01.jpg, the mount alone on white, right side, 2000 x 1334, harvested
Scale: the rings' near side flats in this view, their inner ends 763.5 px apart for the 2.572 in the left view's camera reads (296.9 px/in), and the base's right face 0.19 in further from the lens (294 px/in); its two bolt heads are then 2.01 in apart (590 px) for five slots, 1.969. Read by each round head in the base's right face, 90 px across
Clamp cross bolts, how far the head stands out of the base's right face0.03 in ± 0.02 in 0.8 mmProvisionalPhoto: Armamat 113267060_4.jpg, the mount alone from the rear right and above, the base's rear end toward the lens, 4200 x 2940
Photo 0.03 in ± 0.02 in used
Armamat 113267060_4.jpg, the mount alone from the rear right and above, the base's rear end toward the lens, 4200 x 2940, harvested
Scale: the base's rear end face in its own plane: the channel between the clamp bar and the fixed jaw, 314 px wide at its roof on a gridded crop (0.65 px to the pixel), taken to be the rail's top it clamps (std.picatinny.top_width, 0.835 in, and a hundredth of clearance): 374 px/in. An assumed fit, not a published size. Read by the rear head's knurled rim shows just proud of the face at the base's right rear corner: about 10 px
Clamp nuts, across flats0.51 in ± 0.02 in 13 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 0.51 in ± 0.02 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the front nut's hexagon on the row through its middle, 170 px at the scale of where it stands (332 px/in). Slotted across its end (the reviewer: "slotted hex nuts", turned "with a socket wrench, a broad-bladed screwdriver or simply the spare change in your pocket")
Clamp nuts, the lock washer and nut out from the bar's face0.47 in ± 0.05 in 11.9 mmProvisionalPhoto: Armamat 113267060_4.jpg, the mount alone from the rear right and above, the base's rear end toward the lens, 4200 x 2940
Photo 0.47 in ± 0.05 in used
Armamat 113267060_4.jpg, the mount alone from the rear right and above, the base's rear end toward the lens, 4200 x 2940, harvested
Scale: the base's rear end face in its own plane: the channel between the clamp bar and the fixed jaw, 314 px wide at its roof on a gridded crop (0.65 px to the pixel), taken to be the rail's top it clamps (std.picatinny.top_width, 0.835 in, and a hundredth of clearance): 374 px/in. An assumed fit, not a published size. Read by the rear stud's washer and nut, 178 px out from the bar's outer face; nearer the lens than the face the scale is set on, so no shorter than this
Base, its rear end behind the rear cross bolt0.395 in ± 0.03 in 10 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 0.395 in ± 0.03 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the clamp bar's rear end, column 1881, at the bar's face's scale (319.5 px/in), behind the rear stud's end
Clamp length along the rail (at its foot)2.77 in ± 0.04 in 70.4 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 2.77 in ± 0.04 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the clamp bar, end to end: columns 995 to 1881 at its face's scale. The fixed side's foot in the right side view is 2.84 (columns 172 to 1010 at 295 px/in); its front end slopes
Base, its top face above the rail's top0.4 in ± 0.03 in 10.2 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 0.4 in ± 0.03 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the base's top near edge, row 890 at column 1600 (the dark face begins at row 912), through the camera at the top's own edge, 0.58 in out from the mid-plane: 0.396 in; 0.408 at the clamp bar's face. The near flats' frame reads the same edge 0.425. The arm's top between the rings (row 800) comes out 0.672 in over the rail the same way, and its underside 0.33
The traced outline is in the frame of the rings' near side flats and has the dark side face's upper edge: 0.07 in under the top (the break on its left edge, mid grey and outside the mask) and, in that frame, 0.03 in high, the base's side being further from a lens that stood above the picture. The model lowers the outline as one by that. With it the arm's top is 0.81 in under the rings' axis: Primary Arms' own SLx 1-6x24, sold in this mount, has its saddle's flat 0.793 under its axis, and SIG's TANGO-MSR 0.82.
Base, the break on its top face's left edge0.07 in ± 0.02 in 1.8 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 0.07 in ± 0.02 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the mid-grey band along the top of the base's left side, rows 890 to 912 at column 1600: its height. The arm's top between the rings has the same band, rows 800 to 825 at column 600 (0.077 in). How far in it reaches isn't read: drawn at 45 degrees
Base, the chamfer on its rear top corner (along the mount)0.13 in ± 0.03 in 3.3 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 0.13 in ± 0.03 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the base's rear top corner is cut off from (1838, 857) to (1880, 912) in the left view and from (210, 860) to (172, 915) in the right: 42 and 38 px along the mount, about 0.17 in down. Its length along the mount
Base, the fixed side's foot: its front end ahead of the rear cross bolt2.45 in ± 0.05 in 62.2 mmProvisionalPhoto: Primary Arms PADLXSM_01.jpg, the mount alone on white, right side, 2000 x 1334
Photo 2.45 in ± 0.05 in used
Primary Arms PADLXSM_01.jpg, the mount alone on white, right side, 2000 x 1334, harvested
Scale: the rings' near side flats in this view, their inner ends 763.5 px apart for the 2.572 in the left view's camera reads (296.9 px/in), and the base's right face 0.19 in further from the lens (294 px/in); its two bolt heads are then 2.01 in apart (590 px) for five slots, 1.969. Read by the foot's front corner, column 1010, from the base's rear end at column 172 (838 px at 295 px/in, the base's right face's scale), less what the rear end is behind the bolt (base_behind_rear_bolt)
Ahead of it the fixed side slopes up to the arm's underside (the right side view: from its foot at column 1010 to the arm at column 1140).
Base, the fixed side's front slope: where it meets the arm's underside, ahead of the rear cross bolt2.89 in ± 0.06 in 73.4 mmProvisionalPhoto: Primary Arms PADLXSM_01.jpg, the mount alone on white, right side, 2000 x 1334
Photo 2.89 in ± 0.06 in used
Primary Arms PADLXSM_01.jpg, the mount alone on white, right side, 2000 x 1334, harvested
Scale: the rings' near side flats in this view, their inner ends 763.5 px apart for the 2.572 in the left view's camera reads (296.9 px/in), and the base's right face 0.19 in further from the lens (294 px/in); its two bolt heads are then 2.01 in apart (590 px) for five slots, 1.969. Read by the slope's upper end, column 1140 (as base_foot_front_x). The left side view has the body ahead of the clamp bar rising to the arm's underside in a hollow curve from 2.6 to 3.0 in, traced
Clamp cross bolts, the bar that crosses the channel: its width along the rail0.19 in ± 0.02 in 4.8 mmConfirmedWorked out: {std.picatinny.slot_width} - 0.016in
Worked out 0.19 in ± 0.02 in used
{std.picatinny.slot_width} - 0.016in, harvested
The standard's slot less a clearance of 0.008 in each side: an assumed fit, not a reading.
Each bolt crosses the channel as a flat-sided bar in a recoil slot (the view from below, d4df1c9eae33). Its own size isn't read: it is drawn a little under the slot it lies in.
Clamp nuts, the slot across the end: its width0.08 in ± 0.01 in 2 mmProvisionalPhoto: a photo on file
Photo 0.08 in ± 0.01 in used
a photo on file, harvested
Scale: the nut's own hexagon in the same view, three faces showing, 353 px from corner to corner for the 0.59 in its 0.51 in across flats makes (610 px/in, good to 5%); along the stud, the scale the stack was read at (clamp_nut_h: 575 px/in on the base's rear end). Read by the notch between its two lips, 49 px (rows 2355 to 2404 at column 1085). End on in the left side view (edbba62833fd) the same slot is a gap of about 25 px in the front nut's rim, 0.075 in
Clamp nuts, the slot across the end: its depth0.1 in ± 0.02 in 2.5 mmProvisionalPhoto: a photo on file
Photo 0.1 in ± 0.02 in used
a photo on file, harvested
Scale: the nut's own hexagon in the same view, three faces showing, 353 px from corner to corner for the 0.59 in its 0.51 in across flats makes (610 px/in, good to 5%); along the stud, the scale the stack was read at (clamp_nut_h: 575 px/in on the base's rear end). Read by the notch from the nut's end to its floor, 59 px along the stud (columns 1055 to 1115): 0.097 to 0.103 in by the two scales
Clamp nuts, the round collar between the hexagon and the lock washer: its length0.19 in ± 0.03 in 4.8 mmProvisionalPhoto: a photo on file
Photo 0.19 in ± 0.03 in used
a photo on file, harvested
Scale: the stack's own length out from the bar's face (clamp_nut_h, 0.47 in): what share of it is round. Read by 111 px of the stack's 286 in the first (the hexagon begins at column 1232), 125 of 315 in the second (rows 1525 to 1650 of 1525 to 1840): 39 and 40% of the stack
Each nut is a hexagon with a round collar toward the clamp bar, a groove round the collar, and a split lock washer between it and the bar (the reviewer: "Lock washers keep the nuts from loosening up during use"). The washer and the groove aren't drawn apart: the collar is drawn to the bar's face.
Clamp nuts, the round collar's diameter0.44 in ± 0.03 in 11.2 mmProvisionalPhoto: Armamat 113267060_5.jpg, from below and behind) and 1286e081602a (Armamat 113267060_4.jpg, from the rear right and above
Photo 0.44 in ± 0.03 in used
Armamat 113267060_5.jpg, from below and behind) and 1286e081602a (Armamat 113267060_4.jpg, from the rear right and above, harvested
Scale: the nut's own hexagon in each view, corner to corner (0.59 in for 0.51 across flats). Read by 275 px across the collar for 350 across the hexagon's corners in the view from below (0.46 in); 255 px for 353 in the rear oblique (0.42 in). Between the two
Clamp nuts, the round recess in the end round the stud: its diameter0.33 in ± 0.02 in 8.4 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 0.33 in ± 0.02 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the front nut end on: the dark recess round the stud's end, columns 1070 to 1180 on the row through its middle, at the scale of where the nut's end stands (332 px/in)
Clamp cross bolts, the stud's end in the nut: its diameter0.145 in ± 0.015 in 3.7 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334
Photo 0.145 in ± 0.015 in used
Primary Arms PADLXSM_00.jpg, the mount alone on white, left side, 2000 x 1334, harvested
Scale: a pinhole camera set by the part's own features in this photo: the 30 mm bore's rim on the front ring's rear face is 364 px tall at the mount's mid-plane (308.2 px/in there); the two rings' inner faces show as bands 67 and 9 px wide from their near edges to their far ones and the bore's opening 45 px wide in the first, which puts the lens 18.4 in from the mid-plane with its axis at column 1087; and the lens stood above the picture's top edge (row -54), by the split on the near flats reading 15 px above the bore's centre where the end view has it 0.15 in above. The rings' near side flats are then at 323.5 px/in. Checked on three published things the camera wasn't set by: the nuts' ends, 653 px apart, are five rail slots (1.969 in) apart where they stand, 1.1 in nearer the lens than the mid-plane (1.990 read); the flats are 2.572 in apart for the maker's 2.52 between the rings, an edge break of 0.026 in on each; and the mount is 5.39 in overall, Armamat's 13.7 cm. Read by the front stud's end, a paler disc in the nut's recess, columns 1100 to 1148 (332 px/in)
Base, the chamfer on its rear top corner (down the rear end)0.17 in ± 0.03 in 4.3 mmProvisionalPhoto: Primary Arms PADLXSM_00.jpg, left side) and b0c1e411bf91 (PADLXSM_01.jpg, right side
Photo 0.17 in ± 0.03 in used
Primary Arms PADLXSM_00.jpg, left side) and b0c1e411bf91 (PADLXSM_01.jpg, right side, harvested
Scale: each view's scale at the base's own side (319.5 and 294 px/in). Read by the cut corner runs 55 rows down in each view (857 to 912 on the left, 860 to 915 on the right): 0.17 and 0.19 in. With base_rear_chamfer it leans 53 degrees from level
Rings, the line between cap and lower half as drawn: the groove's width0.008 in ± 0.004 in 0.2 mmProvisionalWorked out: An assumption for the drawing, not a reading: the photos have a dark line between each cap and its lower half, a pixel or two wide, and no view shows a gap in profile. It was a number in the script until the first review, 2026-10-13.
Worked out 0.008 in ± 0.004 in used
An assumption for the drawing, not a reading: the photos have a dark line between each cap and its lower half, a pixel or two wide, and no view shows a gap in profile. It was a number in the script until the first review, 2026-10-13., harvested
Rings, the line between cap and lower half as drawn: the groove's depth0.012 in ± 0.006 in 0.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows it in profile. It was a number in the script until the first review, 2026-10-13.
Worked out 0.012 in ± 0.006 in used
An assumption for the drawing, not a reading: no view on file shows it in profile. It was a number in the script until the first review, 2026-10-13., harvested
Clamp bar, the line between it and the base's shoulder as drawn: the groove's width and depth0.012 in ± 0.006 in 0.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: the left side view has a line along the bar's top, and no view on file shows it in profile. It was a number in the script until the first review, 2026-10-13.
Worked out 0.012 in ± 0.006 in used
An assumption for the drawing, not a reading: the left side view has a line along the bar's top, and no view on file shows it in profile. It was a number in the script until the first review, 2026-10-13., harvested
Clamp nuts, the round recess in the end round the stud: its depth0.07 in ± 0.03 in 1.8 mmProvisionalWorked out: An assumption for the drawing, not a reading: the recess is seen end on only, and no view on file shows it in profile. It was a number in the script until the first review, 2026-10-13.
Worked out 0.07 in ± 0.03 in used
An assumption for the drawing, not a reading: the recess is seen end on only, and no view on file shows it in profile. It was a number in the script until the first review, 2026-10-13., harvested
Clamp cross bolts, the stud's end under the nut's end face0.06 in ± 0.03 in 1.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the stud's end shows inside the nut's recess end on, a little off its floor, and no view on file shows it in profile. It was a number in the script until the first review, 2026-10-13.
Worked out 0.06 in ± 0.03 in used
An assumption for the drawing, not a reading: the stud's end shows inside the nut's recess end on, a little off its floor, and no view on file shows it in profile. It was a number in the script until the first review, 2026-10-13., harvested
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Picatinny rail (MIL-STD-1913)
- Uppers
- Aero Precision M4E1 Enhanced Upper Receiver Stripped, Aero Precision M4E1 Threaded upper receiver, BCM M4 Upper Receiver Assembly (w/ Laser T-Markings), Expo Arms 7075 Stripped AR-15 Upper Receiver, Geissele Automatics Super Duty Stripped Upper Receiver, Nordic Components 22RB .22 LR upper, 16", Palmetto State Armory AR-15 Stripped Upper Receiver, Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12", Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16"
- Handguards
- Aero Precision AR15 10.3" R-ONE M-LOK handguard, Aero Precision AR15 12.7" R-ONE M-LOK handguard, Aero Precision AR15 15" Enhanced M-LOK Handguard, Gen 2, Aero Precision AR15 15" R-ONE M-LOK handguard, Aero Precision AR15 15" S-ONE M-LOK Handguard, Aero Precision AR15 16.6" R-ONE M-LOK handguard, Aero Precision AR15 7.3" R-ONE M-LOK handguard, Aero Precision AR15 9.3" R-ONE M-LOK handguard, BCM MCMR-10 (M-LOK® Compatible* Modular Rail), BCM MCMR-13 (M-LOK® Compatible* Modular Rail), BCM MCMR-15 (M-LOK® Compatible* Modular Rail), Expo Arms Free Float AR-15 Handguard - M-LOK - 15", Geissele Automatics 10.5" Super Modular Rail MK16 M-LOK, Geissele Automatics 13.5" Super Modular Rail MK16 M-LOK, Geissele Automatics 15" Super Modular Rail MK16 M-LOK, MAS Defense 12.62" NERO M-LOK FREE FLOAT, MAS Defense 15" NERO M-LOK FREE FLOAT, MAS Defense 9.87" NERO M-LOK FREE FLOAT, Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length), Midwest Industries Combat Rail One Piece Free Float Handguard, M-LOK™ (15")
- Frames
- Taurus TX22 Gen 2 frame
- Rail sections
- Magpul M-LOK® Aluminum Rail, 3 Slots, Magpul M-LOK® Aluminum Rail, 5 Slots, Magpul M-LOK® Aluminum Rail, 7 Slots, Magpul M-LOK® Aluminum Rail, 9 Slots, Magpul M-LOK® Polymer Rail, 11 Slots, Magpul M-LOK® Polymer Rail, 3 Slots, Magpul M-LOK® Polymer Rail, 5 Slots, Magpul M-LOK® Polymer Rail, 7 Slots, Magpul M-LOK® Polymer Rail, 9 Slots
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Primary Arms $59.99 Black Nov 21, 2026, in stock that day
- KYGUNCO $59.99 Black Nov 21, 2026, out of stock that day
- AR15Discounts $59.99 Black Nov 21, 2026, out of stock that day
- Rifle Supply $63.99 Black Nov 21, 2026, out of stock that day