Red dot mount
Scalarworks LEAP/01 Aimpoint Micro T-2 quick-detach mount, 1.57 in
Scalarworks' quick-detach mount for an Aimpoint Micro T-2 and the dots cut for its footprint, the dot's axis 1.57 in over the rail ("Optic center height over rail ... SW0110 : 1.57"", "Co-Witness ... SW0110 : Lower-Third"). A frame of 7075 with a window through its sides and its ends, leaning forward over its clamp ("Forward lean for additional magnifier space", Primary Arms), clamped by one knurled wheel on the left turned by hand ("Close clamp by turning ClickDrive wheel as tightly as you can by hand (Do not use tools)."). 45 g.

- Weight
- 1.59 oz Conflictpublished: Scalarworks, LEAP/01 (product page, SPECIFICATIONS), the maker, read Nov 3, 2026Its sources span 1.57 oz to 1.68 oz.
- Lowest price
- $159.00 at Scalarworks, read Nov 21, 2026 (Black)
- Maker's number
- SW0110
- Colour
- Black (placeholder)
- Drawn as
- modelled
- Maker's page
- scalarworks.com
In “22RB .22 LR rifle”, a build on the start page, in place of its Holosun 1.63 in lower 1/3 co-witness pedestal mount (HS-MOUNT-AR-RISER-ARO).
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Optical axis above the rail's top, with an Aimpoint Micro T-2 on it (the maker's height)1.57 in 39.9 mmConfirmedPublished: Scalarworks, LEAP/01 (product page, SPECIFICATIONS), the maker, read Nov 3, 2026
Published “Optic center height over rail SW0100 : 1.42" SW0110 : 1.57" SW0120 : 1.93"” used
Scalarworks, LEAP/01 (product page, SPECIFICATIONS), the maker, read Nov 3, 2026 the page, harvested Nov 3, 2026
The same page, at the choice of height: "HEIGHT: 1.42" 1.57" 1.93""; MidwayUSA's page: "Note: Height measurement is from the top of the rail to the center of the optic."
Published “1.57” OPTIC CENTER”
Scalarworks, the technical drawing of SW0110 in the LEAP/01 page's gallery for the 1.57 in height (a copy on file), the maker, read Nov 3, 2026 the page, harvested Nov 3, 2026
From the extension line through the clamp's shaft (the rail's top) to the T-2's axis.
Published “Center Height Over Rail: Absolute Co-Witness : 1.42" (36mm) Lower 1/3 : 1.57" (40mm)”
Wing Tactical, Scalarworks LEAP Aimpoint Micro Mount, a seller, read Nov 3, 2026 the page, harvested Nov 3, 2026
Photo 1.569 in ± 0.006 in
Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. Read by the red dot's centroid (row 557.0) above the extension line (row 1091): 534 px
The maker's stated centre height, the figure a buyer compares and the category's; its drawing's own lines put the axis there to 0.001 in.
The maker names no dot in the sentence ("Optic center height over rail"); the page is "LEAP/01 Premium Aimpoint Micro T-2 mounts.", its drawing of this height draws a T-2 on the mount, and its weight chart weighs it "with all hardware necessary to attach an Aimpoint Micro T-2 in lower-third co-witness height": the height is the T-2's. Its co-witness, in the same table: "SW0110 : Lower-Third".
Top of the window through the mount (end to end), above the rail's top0.846 in 21.5 mmConfirmedPublished: Scalarworks, the technical drawing of SW0110 in the LEAP/01 page's gallery for the 1.57 in height (a copy on file), the maker, read Nov 3, 2026
Published “21.5MM” used
Scalarworks, the technical drawing of SW0110 in the LEAP/01 page's gallery for the 1.57 in height (a copy on file), the maker, read Nov 3, 2026 the page, harvested Nov 3, 2026
From the same extension line as the 1.57 in to the top of the window's throat (the inner of the two outlines drawn round it).
Photo 0.8505 in ± 0.006 in
Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. Read by the throat's top stroke (row 801.5) above the extension line (1091): 289.5 px
21.60 mm: the check of the drawing's scale.
The maker's stated dimension; its lines read the same at the scale the rail and the axis give.
The deck's floor (where the dot's base sits) above the rail's top0.981 in ± 0.037 in 24.9 mmProvisionalWorked out: {.optical_axis_above_rail} - {aimpoint-micro-t-2.axis_above_base}
Worked out 0.981 in ± 0.037 in used
{.optical_axis_above_rail} - {aimpoint-micro-t-2.axis_above_base}, harvested
1.57 in less the T-2's 0.589 in.
Photo 0.965 in ± 0.006 in
Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. Read by the stroke the T-2's foot stands on between the rims (row 762.5, from column 510 to 690) above the extension line (1091): 328.5 px. The T-2's axis is 205.5 px over it in the same drawing: 0.604 in, inside the 0.589 ± 0.037 the T-2's ledger has
The category's figure: the maker's axis height for the T-2 less the T-2's own axis over its base, which puts the T-2 at the maker's 1.57 in. The maker's drawing has the floor 0.016 in lower, inside the two readings' ±.
The deck is a floor between two rims that run its whole length (Wing Tactical's photo from above, b9f81ccd5367): the T-2's foot sits down between them on the floor and its housing's underside on the rims' tops (the drawing). The floor is where a dot's base is put: the T-2's own axis over its base (aimpoint-micro-t-2.axis_above_base) is read to the plane its foot is screwed to. The maker states only the axis's height, for the T-2: the floor is that less the T-2's axis over its base. The drawing puts it there within the two readings' ±.
The deck's two rims, their tops above the rail's top1.046 in ± 0.006 in 26.6 mmCorroboratedPhoto: Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 1.046 in ± 0.006 in used
Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. Read by the rims' top stroke (row 735, from column 440 to 500 and 702 to 760) above the extension line (1091): 356 px
Photo 1.06 in ± 0.015 in
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level). Read by the mount's top edge (row 439, from column 320 to 738) above the teeth's tops: 261.5 px
1.3% over the drawing: the mount's near face stands nearer the lens than the rail's middle the slots are read at (its length reads as much over Wing Tactical's, length).
The maker's drawing, at a scale three of its own figures agree on; the photo reads the near face 1.3% large.
What the side views show as the mount's top. Not drawn above the deck's floor: every Micro dot on file is drawn with its base as wide as its housing, and the rims would stand inside it (the part's approximations).
The footprint's middle along the deck, ahead of the wheel's shaft0.28 in ± 0.05 in 7.1 mmCorroboratedPhoto: Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200
Photo 0.28 in ± 0.05 in used
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level). Read by the middle of the rims' flat top, between the step at its front end (column 320) and where its rear end scoops down (738): column 529, 69.5 px ahead of the wheel's shaft (column 598.5, the slot midway). The lug that goes up into a dot's base is in the middle of the deck in Wing Tactical's photo from above (b9f81ccd5367)
Photo 0.26 in ± 0.06 in
Scalarworks, scalarworks-leap-01-aimpoint-micro-t2-bundle-1.57-side-SW0110-T2.jpg: the mount with a Micro T-2 on it, straight left side, harvested
Scale: the rail section's slots at columns 330.5 and 866.0, six pitches apart: 89.25 px a pitch, 226.5 px/in; the wheel's centre at 597.5. Read by the T-2's rubber covers, lids closed, from column 187 to 877 at its axis: their middle 0.289 in ahead of the wheel; the T-2's model has its footprint's middle 0.03 in behind its covers' middle (aimpoint-micro-t-2.glb, the covers from -1.403 to 1.461 in)
The check: where the T-2 screwed to the footprint has its own footprint's middle.
The mount's own deck; the T-2 on it in the same set-up puts its footprint's middle 0.02 in further back, within both ±.
The clamp's length along the rail, at its foot1.557 in ± 0.03 in 39.5 mmProvisionalPhoto: Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200
Photo 1.557 in ± 0.03 in used
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level). Read by the clamp's foot under the rail's top (row 757), from the front leg's lower end (column 431.1, where the traced outline's foot ends) to the rear face (815): 383.9 px
As read: the near face reads 1.3% large (rim_top_above_rail).
The clamp's foot, its front end ahead of the wheel's shaft0.679 in ± 0.02 in 17.2 mmProvisionalPhoto: Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200
Photo 0.679 in ± 0.02 in used
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level). Read by the traced outline's foot (profiles.side) ends at column 431.1, 167.4 px ahead of the shaft (598.5)
The clamp's foot, its rear end behind the wheel's shaft0.878 in ± 0.02 in 22.3 mmProvisionalPhoto: Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200
Photo 0.878 in ± 0.02 in used
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level). Read by the rear face, column 815, 216.5 px behind the shaft
Overall length along the rail2.06 in 52.3 mmConflictPublished: Wing Tactical, Scalarworks LEAP Aimpoint Micro Mount, a seller, read Nov 3, 2026
Published “Length: 2.06"” used
Wing Tactical, Scalarworks LEAP Aimpoint Micro Mount, a seller, read Nov 3, 2026 the page, harvested Nov 3, 2026
One figure on a page that sells the 1.42 and the 1.57 in; what it spans isn't said.
Photo 2.088 in ± 0.02 in
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level). Read by the deck's front step (column 300) to the rear face (815): 515 px
1.4% over Wing Tactical's: the near face reads 1.3% large (rim_top_above_rail).
A seller's figure, which the photo reads within the 1.3% its near face reads large by.
wing and side-photo differ by 0.028 in beyond what each states it is good to.
Overall width across the clamp1.334 in ± 0.006 in 33.9 mmCorroboratedPhoto: Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 1.334 in ± 0.006 in used
Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. Read by the clamp's two outer faces, the strokes at columns 373.5 and 827.5 (rows 1000 to 1120): 454 px, about column 600.5, the rail's middle
Published “Width: 1.338"”
Wing Tactical, Scalarworks LEAP Aimpoint Micro Mount, a seller, read Nov 3, 2026 the page, harvested Nov 3, 2026
One figure for a page that sells two heights.
The maker's drawing of this height; a seller's figure agrees to 0.004 in.
The maker: "the Leap mount is symmetrical, protruding less than 7mm from either side of your Picatinny rail." (0.835 in and twice 7 mm: under 1.386 in).
The body under the deck, across (its two side walls' outer faces)0.94 in ± 0.006 in 23.9 mmProvisionalPhoto: Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 0.94 in ± 0.006 in used
Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. Read by the walls' strokes at columns 440.5 and 760.5 (rows 750 to 920): 320 px
The clamp's foot below the rail's top0.234 in ± 0.006 in 5.9 mmCorroboratedPhoto: Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 0.234 in ± 0.006 in used
Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. Read by the jaws' feet (row 1170.5, columns 430 to 476 and 723 to 780) under the extension line (1091): 79.5 px
Photo 0.229 in ± 0.01 in
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level). Read by the left jaw's foot (row 757) under the teeth's tops (700.5): 56.5 px
The finer reading; the photo agrees.
ClickDrive wheel, over its teeth0.629 in ± 0.015 in 16 mmProvisionalPhoto: Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200
Photo 0.629 in ± 0.015 in used
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level). Read by the teeth's tips 76.25 px above and 78.75 px below the wheel's centre (column 598.75, row 700): 155 px
The wheel's face is the nearest thing to the lens: as read, perhaps 1.3% large.
Twenty teeth: counted on the side photo's upper half, where the rim is clear of the body (tips about 18 degrees apart: at 9, 29, 45 and 63 degrees from the top).
ClickDrive wheel, at the foot of its teeth0.527 in ± 0.02 in 13.4 mmProvisionalPhoto: Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200
Photo 0.527 in ± 0.02 in used
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level). Read by the valleys between the top teeth, 65 px from the centre
ClickDrive wheel, the face inside its rim0.572 in ± 0.015 in 14.5 mmProvisionalPhoto: Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200
Photo 0.572 in ± 0.015 in used
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level). Read by the bright ring round the face ("SCALARWORKS" inside it), 70.6 px from the centre across
ClickDrive wheel, the socket in its middle0.13 in ± 0.015 in 3.3 mmProvisionalPhoto: Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200
Photo 0.13 in ± 0.015 in used
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level). Read by the dark hole at the wheel's middle, columns 582 to 614
ClickDrive wheel's axis above the rail's top0.002 in ± 0.008 in 0.1 mmProvisionalPhoto: Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200
Photo 0.002 in ± 0.008 in used
Scalarworks, scalarworks-leap-01-quick-detach-mount-1.57-side-SW0110.jpg: SW0110 alone on a rail section, straight left side, 1200 x 1200, harvested
Scale: the rail section's own slots: the gaps of the two that show have their middles at columns 307.0 and 890.0 (the gaps' edges on rows 706 to 724), six pitches apart (std.picatinny.slot_pitch): 97.17 px a pitch, 246.6 px/in at the rail's middle; the teeth's tops on row 700.5 (through the slots the white ground shows down to their floors, 29.5 px lower: the photo is level). Read by the wheel's centre (row 700, midway between its top and bottom teeth's tips and the middle of its socket) above the teeth's tops (700.5)
On the rail's top: the shaft is half in the slot and half in the clamp's roof.
ClickDrive wheel, its outer face left of the mount's middle0.663 in ± 0.006 in 16.8 mmProvisionalPhoto: Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 0.663 in ± 0.006 in used
Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. Read by the wheel's knurl drawn edge on under the left jaw's rounded corner (rows 1140 to 1200), its outer edge at column 374.5, flush with the clamp's left face: 225.75 px from the rail's middle
ClickDrive wheel, across0.167 in ± 0.008 in 4.2 mmProvisionalPhoto: Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 0.167 in ± 0.008 in used
Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. Read by the knurl drawn edge on, columns 374.5 to 431.5: 57 px
The set screw in the rear end (the ball detent's), left of the middle0.579 in ± 0.008 in 14.7 mmProvisionalPhoto: Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 0.579 in ± 0.008 in used
Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. Read by the concentric circles drawn low at the left (its centre at column 403, row 1093): 197.25 px left of the rail's middle
"An integrated spring-loaded ball-detent exerts enough force against the crown to make it completely recoil proof." (the maker's page): a screw in the rear end, in line with the wheel's middle across, at the height of its axis, its red nylon patch in Wing Tactical's photos.
The set screw's hole in the rear end0.106 in ± 0.01 in 2.7 mmProvisionalPhoto: Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 0.106 in ± 0.01 in used
Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. Read by the outermost of its circles, columns 385 to 421
The telescoping jaw: where it is split from the right wall, right of the middle0.51 in ± 0.012 in 13 mmProvisionalPhoto: Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 0.51 in ± 0.012 in used
Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. Read by the two strokes up the right wall at columns 770.5 and 777.5 (rows 1025 to 1105): their middle, 173.75 px right of the rail's middle
"ClickDrive's low-profile thumbscrew and low-friction telescoping clamp ..." (the maker's page): the drawing splits the right wall's lower part off as the jaw that moves, by two strokes 7 px apart up the wall and one across it.
The telescoping jaw, its top above the rail's top0.195 in ± 0.006 in 5 mmProvisionalPhoto: Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo 0.195 in ± 0.006 in used
Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. Read by the stroke across the right wall (row 1024.5, columns 770 to 828) above the extension line (1091)
The telescoping jaw, where it turns in under the rail's head (its top there, below the rail's top)-0.056 in ± 0.01 in -1.4 mmProvisionalPhoto: Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200
Photo -0.056 in ± 0.01 in used
Scalarworks' technical drawing of SW0110: the mount with a T-2 on it from behind, over a rail in section, 1200 x 1200, harvested
Scale: the rail drawn under the mount: its head's widest, rows 1124 to 1126, between the strokes' middles at columns 458.5 and 743.0 (284.5 px for std.picatinny.top_width, .835: 340.7 px/in), 34 px under the extension line (the standard's widest is 0.100 in under the rail's top); the 1.57 in's own lines 534 px apart (340.1) and the 21.5 mm's 289.5 px (342.0): 340.4 px/in, the rail's top at row 1091 and its middle at column 600.25. Read by the two strokes up the right wall curve in at row 1108 to meet the rail's upper face: 17 px under the extension line, as a height
The guide pins' heads on the jaw's outer face, ahead of and behind the shaft's0.53 in ± 0.05 in 13.5 mmProvisionalWorked out: {scalarworks-leap-02-micro-226.guide_pin_x}
Worked out 0.53 in ± 0.05 in used
{scalarworks-leap-02-micro-226.guide_pin_x}, harvested
No view of this mount's right side is on file: the LEAP/02's (Primary Arms' photo of it from the right front, 4945353b7bdf), on the same ClickDrive clamp, is the only one of the family's.
A guide pin's head0.1 in ± 0.02 in 2.5 mmProvisionalWorked out: {scalarworks-leap-02-micro-226.guide_pin_d}
Worked out 0.1 in ± 0.02 in used
{scalarworks-leap-02-micro-226.guide_pin_d}, harvested
The LEAP/02's, as guide_pin_x.
The shaft's end on the jaw's outer face0.15 in ± 0.02 in 3.8 mmProvisionalWorked out: {scalarworks-leap-02-micro-226.shaft_end_d}
Worked out 0.15 in ± 0.02 in used
{scalarworks-leap-02-micro-226.shaft_end_d}, harvested
The LEAP/02's, as guide_pin_x.
The dark ring round each head in the jaw's face0.008 in ± 0.005 in 0.2 mmProvisionalWorked out: {scalarworks-leap-02-micro-226.head_ring}
Worked out 0.008 in ± 0.005 in used
{scalarworks-leap-02-micro-226.head_ring}, harvested
The LEAP/02's, as guide_pin_x.
How deep each head's hole is drawn0.04 in ± 0.02 in 1 mmProvisionalWorked out: An assumption for the drawing, not a reading: the heads are flush with the face in the photo, and what is behind them doesn't show.
Worked out 0.04 in ± 0.02 in used
An assumption for the drawing, not a reading: the heads are flush with the face in the photo, and what is behind them doesn't show., harvested
Clearance round the wheel in its pocket in the left wall0.02 in ± 0.01 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the side photo shows the pocket's rim round the wheel's teeth as a dark ring a few pixels wide, which no scale on file resolves.
Worked out 0.02 in ± 0.01 in used
An assumption for the drawing, not a reading: the side photo shows the pocket's rim round the wheel's teeth as a dark ring a few pixels wide, which no scale on file resolves., harvested
How far the wheel's face is dished inside its rim0.01 in ± 0.01 in 0.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: the side photo shows the face's rim as a bright ring, its depth not; no view on file has the wheel in profile.
Worked out 0.01 in ± 0.01 in used
An assumption for the drawing, not a reading: the side photo shows the face's rim as a bright ring, its depth not; no view on file has the wheel in profile., harvested
The socket in the wheel's middle, its depth0.08 in ± 0.04 in 2 mmProvisionalWorked out: An assumption for the drawing, not a reading: the socket shows dark in the side photo, its depth not.
Worked out 0.08 in ± 0.04 in used
An assumption for the drawing, not a reading: the socket shows dark in the side photo, its depth not., harvested
The set screw's hole in the rear end, its depth0.1 in ± 0.05 in 2.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the drawing has the hole end on, and the screw runs on toward the wheel's crown inside.
Worked out 0.1 in ± 0.05 in used
An assumption for the drawing, not a reading: the drawing has the hole end on, and the screw runs on toward the wheel's crown inside., harvested
How far the set screw's end stands back in its hole0.02 in ± 0.02 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: Wing Tactical's photos show the screw's red nylon patch just inside the hole's rim.
Worked out 0.02 in ± 0.02 in used
An assumption for the drawing, not a reading: Wing Tactical's photos show the screw's red nylon patch just inside the hole's rim., harvested
The aluminium's edges, broken0.008 in ± 0.005 in 0.2 mmProvisionalWorked out: An assumption for the drawing, not a reading: the photos show every edge of the body softened, by an amount no view on file resolves.
Worked out 0.008 in ± 0.005 in used
An assumption for the drawing, not a reading: the photos show every edge of the body softened, by an amount no view on file resolves., harvested
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Picatinny rail (MIL-STD-1913)
- Uppers
- Aero Precision M4E1 Enhanced Upper Receiver Stripped, Aero Precision M4E1 Threaded upper receiver, BCM M4 Upper Receiver Assembly (w/ Laser T-Markings), Expo Arms 7075 Stripped AR-15 Upper Receiver, Geissele Automatics Super Duty Stripped Upper Receiver, Nordic Components 22RB .22 LR upper, 16", Palmetto State Armory AR-15 Stripped Upper Receiver, Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12", Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16"
- Handguards
- Aero Precision AR15 10.3" R-ONE M-LOK handguard, Aero Precision AR15 12.7" R-ONE M-LOK handguard, Aero Precision AR15 15" Enhanced M-LOK Handguard, Gen 2, Aero Precision AR15 15" R-ONE M-LOK handguard, Aero Precision AR15 15" S-ONE M-LOK Handguard, Aero Precision AR15 16.6" R-ONE M-LOK handguard, Aero Precision AR15 7.3" R-ONE M-LOK handguard, Aero Precision AR15 9.3" R-ONE M-LOK handguard, BCM MCMR-10 (M-LOK® Compatible* Modular Rail), BCM MCMR-13 (M-LOK® Compatible* Modular Rail), BCM MCMR-15 (M-LOK® Compatible* Modular Rail), Expo Arms Free Float AR-15 Handguard - M-LOK - 15", Geissele Automatics 10.5" Super Modular Rail MK16 M-LOK, Geissele Automatics 13.5" Super Modular Rail MK16 M-LOK, Geissele Automatics 15" Super Modular Rail MK16 M-LOK, MAS Defense 12.62" NERO M-LOK FREE FLOAT, MAS Defense 15" NERO M-LOK FREE FLOAT, MAS Defense 9.87" NERO M-LOK FREE FLOAT, Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length), Midwest Industries Combat Rail One Piece Free Float Handguard, M-LOK™ (15")
- Frames
- Taurus TX22 Gen 2 frame
- Rail sections
- Magpul M-LOK® Aluminum Rail, 3 Slots, Magpul M-LOK® Aluminum Rail, 5 Slots, Magpul M-LOK® Aluminum Rail, 7 Slots, Magpul M-LOK® Aluminum Rail, 9 Slots, Magpul M-LOK® Polymer Rail, 11 Slots, Magpul M-LOK® Polymer Rail, 3 Slots, Magpul M-LOK® Polymer Rail, 5 Slots, Magpul M-LOK® Polymer Rail, 7 Slots, Magpul M-LOK® Polymer Rail, 9 Slots
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Scalarworks $159.00 Black Nov 21, 2026, in stock that day
- T.REX ARMS $159.00 Black Nov 21, 2026, in stock that day
- MidwayUSA $159.00 Black Nov 21, 2026, in stock that day