Handguard
Magpul MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4
Magpul's polymer drop-in hand guard for a carbine-length gas system, in two halves: "Replaces standard AR15/M4 hand guards on carbine-length gas systems"; "Compatible with most piston-driven as well as 'direct impingement' gas systems"; "M-LOK slots at the two, six, and ten o'clock positions"; "The integral, riveted aluminum heat shield, combined with the front lower lip and side extensions, shields the support hand from a hot gas block"; "Relief cut at the top rear of the handguard accommodates overhanging optics"; "Constructed of reinforced, heat-resistant Magpul polymer"; "Made in the USA" (Magpul). It goes on the rifle's own barrel nut and delta ring and the cap behind its front sight base: no free-float nut of its own.

- Weight
- 6.8 oz Confirmedpublished: Magpul, MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4, Model MAG424: Specifications, the maker, read Oct 28, 2026
- Lowest price
- $29.84 at Primary Arms, read Nov 21, 2026 (Olive Drab Green)
- Maker's number
- MAG424
- Colours
- Black, Flat Dark Earth, Olive Drab Green, Stealth Gray
- Drawn as
- modelled
- Maker's page
- magpul.com
In “BCM 11.5 in carbine, suppressed”, a build on the start page, in place of its BCM MCMR-10 (M-LOK® Compatible* Modular Rail). The BCM G.I. Barrel Nut - AR15 and the BCM Delta Ring Assembly - AR15 and the BCM Front Sight Base F - FSB (ID .750) - Milspec for Flat Top Uppers and the BCM Handguard Cap Round - .750 AR15 go in with it: its maker says it needs them.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Length, overall7.1 in 180.3 mmConfirmedPublished: Magpul, MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4, Model MAG424: Specifications, the maker, read Oct 28, 2026
Published “Length, overall: 7.1 in.” used
Magpul, MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4, Model MAG424: Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Published “It measures 7.1" long, 2.5" tall, and 2.2" wide”
Primary Arms, Magpul MOE Drop In AR-15 Handguard - M-LOK - Carbine Length (black, MAG424-BLK), a seller, read Oct 28, 2026 the page, harvested Oct 28, 2026
Photo 7.14 in ± 0.02 in
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%). Read by the outline's x-extent (958 px, columns 96 to 1054, luminance under 230) at its three M-LOK slots' scale (134.2 px/in): its rear end to the tip of its front end
The maker's figure, which Primary Arms' page repeats; the photo, scaled by the standard's M-LOK slots and by no length of the part, agrees within 0.04 in (0.5%).
From its rear end, which stands in the delta ring's skirt against the ring's lip, to the tip of its front end, which wraps the front sight base's rear. The photo shows the rear end too: the part is alone in it.
Length, mounting (from its rear end in the delta ring to its front flange's end in the cap)6.6 in 167.6 mmConfirmedPublished: Magpul, MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4, Model MAG424: Specifications, the maker, read Oct 28, 2026
Published “Length, mounting: 6.6 in.” used
Magpul, MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4, Model MAG424: Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Magpul says no more than the figure. Taken as from the rear end that bears on the delta ring's lip to the front end of the front flange, which its instructions slide "into the metal Hand Guard cap, located behind the front sight base" (one sheet for the three lengths).
Width2.2 in 55.9 mmConfirmedPublished: Magpul, MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4, Model MAG424: Specifications, the maker, read Oct 28, 2026
Published “Width 2.2 in.” used
Magpul, MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4, Model MAG424: Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Published “It measures 7.1" long, 2.5" tall, and 2.2" wide”
Primary Arms, Magpul MOE Drop In AR-15 Handguard - M-LOK - Carbine Length (black, MAG424-BLK), a seller, read Oct 28, 2026 the page, harvested Oct 28, 2026
The maker's figure; Primary Arms' page states the same.
No view on file looks at it from above or from an end square on: drawn at Magpul's figure, which no photo checks (its height reads 5% under Magpul's in the level photo).
Height, excluding the front lower lip2.38 in ± 0.02 in 60.5 mmConflictPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Published “Height, excluding lip: 2.5 in.”
Magpul, MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4, Model MAG424: Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Published “It measures 7.1" long, 2.5" tall, and 2.2" wide”
Primary Arms, Magpul MOE Drop In AR-15 Handguard - M-LOK - Carbine Length (black, MAG424-BLK), a seller, read Oct 28, 2026 the page, harvested Oct 28, 2026
Photo 2.38 in ± 0.02 in used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%). Read by the body's top (row 220) to its bottom (row 540) clear of both ends and the lip (columns 165 to 900): 320 px; 2.37 at the length's scale, 2.385 at the slots'; ± 2 px
The level photo, scaled by Magpul's own overall length and by the standard's M-LOK slots (the two within 0.5%), has the body 2.38 tall clear of the lip; Magpul's 2.5 is 5% more, and what it measures over isn't said (the lip reaches 2.63 in the same photo). A side view seen from a little above or below would read taller, not shorter.
magpul and photo differ by 0.12 in beyond what each states it is good to.
primary-arms and photo differ by 0.12 in beyond what each states it is good to.
Inside diameterNo value yetMissingNo source yet
Magpul gives none. The model's inside is its outside less the wall (wall), which no view gives either.
Its rear end (bearing on the delta ring's lip) ahead of the receiver's front face0.336 in ± 0.015 in 8.5 mmProvisionalWorked out: {std.ar15.slip_ring_front_x}
Worked out 0.336 in ± 0.015 in used
{std.ar15.slip_ring_front_x}, harvested
Where the standard's delta ring holds it: its rear end in the ring's skirt, against the lip (std.ar15.slip_ring_front_x, from the Army's drawings). Its instructions: "make sure your delta ring is securing BOTH upper and lower rear flanges of the Hand Guards".
Where its body shows ahead of the delta ring (the ring's skirt's front end), from its rear end0.12 in ± 0.005 in 3 mmConfirmedWorked out: {std.ar15.slip_ring_skirt_length}
Worked out 0.12 in ± 0.005 in used
{std.ar15.slip_ring_skirt_length}, harvested
Its rear end stands in the ring's front skirt (std.ar15.slip_ring_skirt_length). The photo of it alone shows that end: two half rings, one on each half.
Its top above the bore axis1.18 in ± 0.03 in 30 mmProvisionalPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Photo 1.18 in ± 0.03 in used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%). Read by the rear end's middle (the outline's rear end, rows 337 to 421 at column 96 and 268 to 493 at 119, about the bore: row 379.5) to the body's top (row 220, the crown between its vents): 159.5 px; ± 3 px
Its body's bottom (clear of the lip) below the bore axis1.19 in ± 0.03 in 30.2 mmProvisionalPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Photo 1.19 in ± 0.03 in used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%). Read by the rear end's middle (row 379.5) to the body's bottom (row 539.5, columns 165 to 900): 160 px; ± 3 px
The body is about centred on the bore: 1.18 above and 1.19 below.
The seam between its two halves, on the sides, above the bore axis (negative below)-0.33 in ± 0.03 in -8.4 mmProvisionalPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Photo -0.33 in ± 0.03 in used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%). Read by the dark line along its side (rows 422 to 425 at columns 300 and 450, luminance 13 to 19 between 50 above and 47 below), 44 px under the rear end's middle (row 379.5); ± 2 px
The gap between its two halves' rear flanges at each side (where the backdrop shows through)0.36 in ± 0.03 in 9.1 mmProvisionalPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Photo 0.36 in ± 0.03 in used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%). Read by the backdrop seen through the rear end at columns 100 and 108: rows 365 to 413 (luminance over 240), 48 px; ± 2 px
The two halves' rear flanges are half rings, apart at the sides: the level photo sees the backdrop through the gap between them.
That gap's middle above the bore axis (negative below)-0.07 in ± 0.03 in -1.8 mmProvisionalPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Photo -0.07 in ± 0.03 in used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%). Read by the gap's middle (row 389) less the rear end's middle (row 379.5): 9.5 px under the axis; ± 2 px
The room inside its M-LOK faces before what runs through it (how far an accessory's nuts may reach in)No value yetMissingNo source yet
Depends on the barrel, the gas tube and the heat shield under it, and on the wall, which no view gives: no figure, so the check reads as unmade.
M-LOK slots in each upper side face (the two and ten o'clock rows)3ProvisionalPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Photo 3 count used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: none: a count. Read by three slots in the right side's row; three in the left's on Primary Arms' OD green (431dc8b3dc62) and black (8014084a9a99) photos and on Magpul's feature photos on a rifle (8e445b9aae44, 1274be34aad7); the instruction sheet draws three for each length
The side rows' rearmost M-LOK slot (its centre), from its rear end1.83 in ± 0.02 in 46.5 mmProvisionalPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Photo 1.83 in ± 0.02 in used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%). Read by the rearmost slot's centre (column 343.0, between its edges at 258.0 and 428.1 at luminance 25 along rows 348 to 362) less the outline's rear end (column 96): 247 px; ± 2 px. The next two at 554.2 and 765.6: 211.3 px apart, the standard's pitch
The side rows' slot centres above the bore axis0.16 in ± 0.02 in 4.1 mmProvisionalPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Photo 0.16 in ± 0.02 in used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%). Read by each slot's edges at half the luminance step down columns 343 and 554 (rows 338.5 and 377.5): centre 358, 21.5 px over the rear end's middle (row 379.5); ± 2 px
The side M-LOK faces' outward direction about the bore axis, from straight up (degrees)78° ± 12°ConflictPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Published “M-LOK slots at the two, six, and ten o'clock positions”
Magpul, MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4, Model MAG424: Specifications, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Photo 78 deg ± 12 deg used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%). Read by each slot's height in the level side view, 39 px (rows 338.5 to 377.5), against the standard's 7 mm width (std.mlok.slot_width, 37.2 px): a face no more than about 20° from upright, its slots' centres 0.16 over the axis at the side
Magpul's "two ... ten o'clock" says which faces, not their angle: a face 60° from up would show its 7 mm slots 0.24 in tall in a level side view, and they show 0.29 in this one. The accessories on them stand out at the angle the faces have.
magpul and photo differ by 18° beyond what each states it is good to.
The side M-LOK faces' distance from the bore axis (along their outward direction)1.046 in ± 0.04 in 26.6 mmProvisionalWorked out: ({.width} / 2 - {.face_flat} / 2 * cos({.mlok_side_face_angle})) * sin({.mlok_side_face_angle}) + {.mlok_side_slot_y} * cos({.mlok_side_face_angle})
Worked out 1.0462 in ± 0.04 in used
({.width} / 2 - {.face_flat} / 2 * cos({.mlok_side_face_angle})) * sin({.mlok_side_face_angle}) + {.mlok_side_slot_y} * cos({.mlok_side_face_angle}), harvested
The face's flat runs up from the side at full width (its lower edge), leaning in at the face's angle, its middle where the photo has the slots' centres (mlok_side_slot_y): the plane through it.
The underside's M-LOK face, its distance below the bore axis1.19 in ± 0.03 in 30.2 mmProvisionalWorked out: {.bottom_below_axis}
Worked out 1.19 in ± 0.03 in used
{.bottom_below_axis}, harvested
M-LOK slots in the underside (six o'clock)3ProvisionalWorked out: {.mlok_side_slots}
Worked out 3 count used
{.mlok_side_slots}, harvested
The underside's rearmost M-LOK slot (its centre), from its rear end1.83 in ± 0.3 in 46.5 mmProvisionalWorked out: {.mlok_side_slot0_x}
Worked out 1.83 in ± 0.3 in used
{.mlok_side_slot0_x}, harvested
The pockets along each side of the lower half (one in each panel between its ribs)4ProvisionalPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Photo 4 count used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: none: a count. Read by four along row 508 (dark runs at columns 252 to 763); four on Primary Arms' OD green (431dc8b3dc62) and Magpul's MVG photo (8e445b9aae44)
The lower half's rearmost pocket (its centre), from its rear end1.42 in ± 0.02 in 36.1 mmProvisionalPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Photo 1.42 in ± 0.02 in used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%). Read by the dark runs along rows 503 to 513 at luminance 40: centres 287.3, 433.1, 580.0 and 727.3, the rearmost 191.3 px ahead of the rear end (column 96); ± 2 px
The lower half's pockets, centre to centre1.09 in ± 0.01 in 27.7 mmProvisionalPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Photo 1.09 in ± 0.01 in used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%). Read by three gaps between the four pockets' centres, 440 px from the first to the last: 146.7 px each
Each pocket's length along it0.52 in ± 0.02 in 13.2 mmProvisionalPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Photo 0.52 in ± 0.02 in used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%). Read by the four dark runs along rows 503 to 513, 70.4 to 78.3 px at luminance 40 and 70.2 to 71.5 at 36 (its ends' bevels lighter): 71 px; ± 3 px
The pockets' centres above the bore axis (negative below)-0.96 in ± 0.02 in -24.4 mmProvisionalPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Photo -0.96 in ± 0.02 in used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%). Read by the pockets' dark rows 500 to 517 at columns 300 and 450 (luminance 24 to 39 between 57 above and 46 below): centre 508.5, 129 px under the rear end's middle (row 379.5); ± 2 px
Each pocket's height0.13 in ± 0.02 in 3.3 mmProvisionalPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Photo 0.13 in ± 0.02 in used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in; its three M-LOK slots, 211.3 px apart for the standard's 40 mm (std.mlok.slot_pitch), give 134.2 (0.5%). Read by the same dark rows, 500 to 517: 17 px; ± 2 px. The level photo of a black one shows each pocket whole
The vents along its crown4ProvisionalPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Photo 4 count used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: none: a count. Read by four dips in the top of the level outline, where the vents cut the crown's line; four rounded slots along the top in Magpul's Stealth Gray shot (ebf5bc6f3e4d) and Primary Arms' black one from above (8014084a9a99)
The rearmost vent's middle, from its rear end2.03 in ± 0.03 in 51.6 mmProvisionalPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Photo 2.03 in ± 0.03 in used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: its overall length (length, 7.1 in) over the outline's 958 px: 134.93 px/in. Read by the traced outline's top: dips 0.037 in deep from 1.764 to 2.296, 2.888 to 3.465, 4.034 to 4.604 and 5.203 to 5.750; the rearmost's middle
The vents, middle to middle1.15 in ± 0.02 in 29.2 mmProvisionalPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Photo 1.15 in ± 0.02 in used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: 134.93 px/in. Read by the four dips' middles, 2.03, 3.18, 4.32 and 5.48: 3.45 in over three gaps
Each vent's length along it0.55 in ± 0.03 in 14 mmProvisionalPhoto: Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768
Photo 0.55 in ± 0.03 in used
Primary Arms' gallery for the black MAG424, MAG424-BLK_01: the hand guard alone, its right side seen level on white, 1152 x 768, harvested
Scale: 134.93 px/in. Read by the four dips' lengths, 0.532 to 0.577: the vents' ends where they meet the crown's line
Each vent's width across the crown0.16 in ± 0.05 in 4.1 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view looks down on the crown square; in the three-quarter shots each vent is about a quarter as wide as long, foreshortened by an angle the photo doesn't give.
Worked out 0.16 in ± 0.05 in used
An assumption for the drawing, not a reading: no view looks down on the crown square; in the three-quarter shots each vent is about a quarter as wide as long, foreshortened by an angle the photo doesn't give., harvested
The ribs between the lower half's panels (and round them), their width0.12 in ± 0.04 in 3 mmProvisionalWorked out: An assumption for the drawing, not a reading: the ribs show as lit and shaded lines a few pixels wide between the pockets in the photos on file, their width and how far they stand on no view in section.
Worked out 0.12 in ± 0.04 in used
An assumption for the drawing, not a reading: the ribs show as lit and shaded lines a few pixels wide between the pockets in the photos on file, their width and how far they stand on no view in section., harvested
How far the lower half's panels stand in from its ribs0.02 in ± 0.01 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the panels' edges catch the light in the three-quarter photos, how deep they are isn't seen in profile.
Worked out 0.02 in ± 0.01 in used
An assumption for the drawing, not a reading: the panels' edges catch the light in the three-quarter photos, how deep they are isn't seen in profile., harvested
Each pocket's depth into the wall0.06 in ± 0.03 in 1.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows a pocket in section; they aren't through (Primary Arms' OD green one, 431dc8b3dc62, shows its own colour in them, not the backdrop).
Worked out 0.06 in ± 0.03 in used
An assumption for the drawing, not a reading: no view on file shows a pocket in section; they aren't through (Primary Arms' OD green one, 431dc8b3dc62, shows its own colour in them, not the backdrop)., harvested
Its polymer wall's thickness0.15 in ± 0.05 in 3.8 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows an end square on or a section. The mid-length's assumption, one moulding of one maker's (at 0.1 in that model was 38% under Magpul's weight at the polymer's density on file); checked here against Magpul's 6.8 oz for this one (its test). What the model lacks is the inner ribs and bosses no view shows.
Worked out 0.15 in ± 0.05 in used
An assumption for the drawing, not a reading: no view on file shows an end square on or a section. The mid-length's assumption, one moulding of one maker's (at 0.1 in that model was 38% under Magpul's weight at the polymer's density on file); checked here against Magpul's 6.8 oz for this one (its test). What the model lacks is the inner ribs and bosses no view shows., harvested
Its aluminium heat shield's thickness0.03 in ± 0.015 in 0.8 mmProvisionalWorked out: An assumption for the drawing, not a reading: the shield shows only through the slots and at the open front end, never in section.
Worked out 0.03 in ± 0.015 in used
An assumption for the drawing, not a reading: the shield shows only through the slots and at the open front end, never in section., harvested
The seam's groove along each side (its width and its depth)0.02 in ± 0.01 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the seam shows as a dark line three or four pixels wide at 135 px to the inch in the level photo (0.02 to 0.03 in), its depth on no view.
Worked out 0.02 in ± 0.01 in used
An assumption for the drawing, not a reading: the seam shows as a dark line three or four pixels wide at 135 px to the inch in the level photo (0.02 to 0.03 in), its depth on no view., harvested
Each upper side face's flat (where its M-LOK slots are), its height across the face0.62 in ± 0.1 in 15.7 mmProvisionalWorked out: An assumption for the drawing, not a reading: the slot's 7 mm and a margin each side as wide as the slots' 8 mm webs, which is how Primary Arms' black one (8014084a9a99) shows the raised band round its slots.
Worked out 0.62 in ± 0.1 in used
An assumption for the drawing, not a reading: the slot's 7 mm and a margin each side as wide as the slots' 8 mm webs, which is how Primary Arms' black one (8014084a9a99) shows the raised band round its slots., harvested
Its top's flat (the crown, between the upper side faces' rounds), half its width0.5 in ± 0.15 in 12.7 mmProvisionalWorked out: An assumption for the drawing, not a reading: no end view on file; Primary Arms' three-quarter photos (8014084a9a99, 431dc8b3dc62) show a rounded crown about as wide as the bore's two sides above the faces.
Worked out 0.5 in ± 0.15 in used
An assumption for the drawing, not a reading: no end view on file; Primary Arms' three-quarter photos (8014084a9a99, 431dc8b3dc62) show a rounded crown about as wide as the bore's two sides above the faces., harvested
Its underside's flat (where the six o'clock slots are), half its width0.45 in ± 0.15 in 11.4 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file looks at the underside; Magpul's feature photo with its MVG on (8e445b9aae44) shows a flat underside a little narrower than the grip's base, rounding into the sides.
Worked out 0.45 in ± 0.15 in used
An assumption for the drawing, not a reading: no view on file looks at the underside; Magpul's feature photo with its MVG on (8e445b9aae44) shows a flat underside a little narrower than the grip's base, rounding into the sides., harvested
Its front flange (what goes into the hand guard cap), outside diameter1.36 in ± 0.05 in 34.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the flange goes "into the metal Hand Guard cap" (its instructions) and Magpul says it takes a round or a triangular cap; no view shows it but end-on from the front (Primary Arms' OD green one, 431dc8b3dc62: an arc inside the body). Taken inside both caps on file: the triangular cap's sides stand 0.689 from the axis inside at their middles (bcm-handguard-cap-triangle-750: side_r less side_centre_r less the sheet), the round cap's two tabs at 3 and 9 o'clock to 0.690.
Worked out 1.36 in ± 0.05 in used
An assumption for the drawing, not a reading: the flange goes "into the metal Hand Guard cap" (its instructions) and Magpul says it takes a round or a triangular cap; no view shows it but end-on from the front (Primary Arms' OD green one, 431dc8b3dc62: an arc inside the body). Taken inside both caps on file: the triangular cap's sides stand 0.689 from the axis inside at their middles (bcm-handguard-cap-triangle-750: side_r less side_centre_r less the sheet), the round cap's two tabs at 3 and 9 o'clock to 0.690., harvested
Its front flange's length (into the cap)0.42 in ± 0.1 in 10.7 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view shows the flange from the side. Long enough that the front wall it stands from stays behind either cap's rim with the flange home (the round cap is 0.276 deep, the triangular 0.323).
Worked out 0.42 in ± 0.1 in used
An assumption for the drawing, not a reading: no view shows the flange from the side. Long enough that the front wall it stands from stays behind either cap's rim with the flange home (the round cap is 0.276 deep, the triangular 0.323)., harvested
Its rear end (what stands in the delta ring's skirt), outside diameter1.72 in ± 0.03 in 43.7 mmProvisionalWorked out: An assumption for the drawing, not a reading: its rear end stands in the delta ring's skirt (std.ar15.slip_ring_skirt_d, 1.750 inside) and shows on no photo; taken 0.03 under the skirt.
Worked out 1.72 in ± 0.03 in used
An assumption for the drawing, not a reading: its rear end stands in the delta ring's skirt (std.ar15.slip_ring_skirt_d, 1.750 inside) and shows on no photo; taken 0.03 under the skirt., harvested
Its front wall (the inner face the front flange stands from), from its rear end6.03 in ± 0.12 in 153.2 mmProvisionalWorked out: {.mounting_length} - {.front_flange_length} - {.wall}
Worked out 6.03 in ± 0.12 in used
{.mounting_length} - {.front_flange_length} - {.wall}, harvested
Ahead of the wall the shell runs on open to its front tip, over the cap and the front sight base's rear ("Hand guard will wrap around the front sight when mounted").
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Drop-in handguard's front in its cap
Handguard mount
Drop-in handguard's hold
- Delta rings
- BCM Delta Ring Assembly - AR15
Gas system length
M-LOK
- Hand stops
- BCM KAG (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK Hand Stop (fit unchecked), Magpul M-LOK Index Panel (fit unchecked)
- Vertical grips
- BCM Vertical Grip Mod 3 (M-LOK® Compatible*) (fit unchecked), Magpul M-LOK MVG vertical grip (fit unchecked)
- Lights
- Cloud Defensive REIN (fit unchecked), Streamlight ProTac Rail Mount HL-X (fit unchecked), SureFire Mini Scout Light Pro (fit unchecked), SureFire Scout Light Pro Dual Fuel (fit unchecked)
- Rail sections
- Magpul M-LOK® Aluminum Rail, 3 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 5 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 7 Slots (fit unchecked), Magpul M-LOK® Aluminum Rail, 9 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 11 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 3 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 5 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 7 Slots (fit unchecked), Magpul M-LOK® Polymer Rail, 9 Slots (fit unchecked)
- Adapter plates
- Magpul M-LOK Hand Stop MOE Adapter (fit unchecked)
- Sling mounts
- Magpul M-LOK QD Sling Mount (fit unchecked)
- Rail covers
- Magpul M-LOK Rail Cover Type 2 (fit unchecked)
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Primary Arms $29.84 Olive Drab Green Nov 21, 2026, in stock that day
- Primary Arms $29.84 Black Nov 17, 2026, in stock that day
- Primary Arms $29.84 Flat Dark Earth Nov 17, 2026, in stock that day
- Midwest Gun Works $35.10 Black Nov 21, 2026, in stock that day
- Midwest Gun Works $35.10 Flat Dark Earth Nov 21, 2026, in stock that day
- Midwest Gun Works $35.10 Olive Drab Green Nov 21, 2026, in stock that day
- Midwest Gun Works $35.10 Stealth Gray Nov 21, 2026, in stock that day
- Magpul $36.95 Black Nov 21, 2026, stock not said
- Magpul $36.95 Flat Dark Earth Nov 21, 2026, stock not said
- Magpul $36.95 Olive Drab Green Nov 21, 2026, stock not said
- Magpul $36.95 Stealth Gray Nov 21, 2026, stock not said