Hand stop
Magpul M-LOK Hand Stop
The hand stop of Magpul's M-LOK Hand Stop Kit (MAG608), which is the only way it is sold: with an index panel, a Type 2 rail cover and an adapter plate for Magpul polymer hand guards. Reinforced polymer with the TSP texture; Black, FDE, ODG, Stealth Gray. On a machined metal or narrow M-LOK hand guard it bolts straight into a slot with its two T-nuts (Magpul's instruction sheet 072-0098-A, scenario 1): it needs no plate under it.

- Weight
- 0.6 oz ± 0.05 oz Provisionalpublished: Wing Tactical, Magpul M-LOK Handstop Kit (MAG-608), Specifications (source of the figures unstated), a seller, read Oct 2, 2026
- Lowest price
- Sold in the Magpul M-LOK Hand Stop Kit, not by itself
- Colours
- Black, FDE, ODG, Stealth Gray
- Drawn as
- modelled
- Maker's page
- magpul.com
In “Two-tone 16 in, Stealth Gray and soft-shooting”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Overall length (the base plate, along the handguard)1.575 in ± 0.012 in 40 mmCorroboratedPhoto: Supplied in chat 2026-10-02: a gallery image of an M-LOK handguard, straight side view, the hand stop and the index panel installed, rail teeth along the top, 2796 x 1290
Photo 1.575 in ± 0.012 in used
Supplied in chat 2026-10-02: a gallery image of an M-LOK handguard, straight side view, the hand stop and the index panel installed, rail teeth along the top, 2796 x 1290, from the site owner
Scale: the handguard's rail teeth in the same image (calibrate.py rail: 16 slots, 132.58 px/slot, drift +0.04%, rms 0.002 in): 336.5 px/in. Read by the base plate's two ends: the hook's front wall (u 687 to 691, rows 800 to 950) and the gap before the next rail cover (u 1217 to 1221, rows 745 to 785): 530 px; ± 4 px
Photo 1.564 in ± 0.02 in
US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi, harvested
Scale: the two screw holes' centres, 1026 px apart, taken as the M-LOK interval (std.mlok.interval, 20 mm: Magpul's FAQ). Read by the plan view's length, 2038 px, over the holes' spacing; the centres by eye on a half-size crop, ± 6 px
Measured on an image of the product, in the plane of its scale. The patent's plan view, scaled by its own screw holes, agrees within 0.011 in. Both are 40 mm, the M-LOK slot pitch, within their ±.
The plate covers one slot pitch. A retailer's staff and a customer put the kit's three pieces together at about 4.75 in (OpticsPlanet, MidwayUSA; neither page on file): three of these. The first reading, 1.334, was the hook alone (the subject's header).
Height (how far it stands off the handguard's face)1.505 in ± 0.03 in 38.2 mmConflictPhoto: US D755,333 S (Magpul, 'Hand stop for a firearm'), FIG. 6 right side elevation, 300 dpi
Photo 1.505 in ± 0.03 in used
US D755,333 S (Magpul, 'Hand stop for a firearm'), FIG. 6 right side elevation, 300 dpi, harvested
Scale: scale from magpul-mlok-hand-stop.length = 1.575 in (x-extent 1549 px → 983.5 px/in). Read by height of the traced outline (tools/trace.py); the patent's side elevation scaled to the plate's length: the mounting face to the lip's lowest point
Photo 1.449 in ± 0.02 in
Supplied in chat 2026-10-02: a gallery image of an M-LOK handguard, straight side view, the hand stop and the index panel installed, rail teeth along the top, 2796 x 1290, from the site owner
Scale: the handguard's rail teeth in the same image (calibrate.py rail: 16 slots, 132.58 px/slot, drift +0.04%, rms 0.002 in): 336.5 px/in. Read by the plate's top edge (row 714, where its rounded ends begin either side of the hook) to the lip's lowest point (row 1201.5): 487.5 px; ± 3 px at each. Until 2026-10-05 this was read from row 688.5 and stood at 1.524: the band from there down to row 712 runs on unbroken past both ends of the plate and over the covers beside it, so it is the handguard's and not the plate's (seen on a contrast-stretched crop of that band while the index panel was measured on the same image)
Line art, whole and orthographic, and what the outline is traced from. The image has the stop 0.056 in less from its plate's top edge to its lip, and the plate 0.208 in thick where the patent's outermost line on that side gives 0.246: the ears' tips look that much lower on the part as made than the patent's outermost line (the index panel's plate, the same plate, reads 0.213 in the same image). Nothing moves by it: the part is seated by the band between its ears, which the hook is measured from the same in both.
patent and render differ by 0.056 in beyond what each states it is good to.
The ears' tips to the lip's lowest point. The patent's side elevation, scaled to the plate's length, is the outline; the image is a second reading and disagrees by about a twentieth of an inch at the ears (2026-10-05: until then it was read from the handguard's own band and seemed to agree). Below the plate's outer surface the hook reads 1.230 in the image (row 788 down) and 1.255 in the patent.
Width (side to side)1.053 in ± 0.03 in 26.7 mmProvisionalPhoto: US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi
Photo 1.053 in ± 0.03 in used
US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi, harvested
Scale: the plan view's own length, 2038 px, as the plate's length (.length, 1.575 in). Read by the plan view's width, 1363 px, at the mounting face (the widest: the stop tapers to its lip). The front and rear elevations (FIG. 3, FIG. 4), drawn at the same scale, read 1361. ± covers the length's ± and a design patent's fidelity (the MOE+, MOE Carbine and MOE SL patents read within 0.6% of Magpul's figures; the K2+'s 13% over)
No published figure. From Magpul's design patent, scaled by the plate's length.
M-LOK slots its lugs span1ConflictPhoto: US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi
Photo 1 count used
US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi, harvested
Scale: the plan view's length as the plate's (.length). Read by the two screw holes stand 0.79 in apart on a 1.575 in plate: one 32 mm slot takes both nuts, and the plate covers that slot's pitch
Published “The hand stop occupies two M-LOK slots, the index panel one slot, and the rail cover spans two.”
rifleconfigurator.com, Magpul M-LOK Hand Stop Kit (a configurator site; source of the statement unstated), a review, read Oct 2, 2026 the page, harvested Oct 2, 2026
Two nuts a 20 mm interval apart sit in one slot, and a plate one pitch long covers one; the site's statement is unattributed and may count the kit's pieces together.
photo and configurator differ by 1 beyond what each states it is good to.
The base plate is one slot pitch long (40 mm) and its two screws a 20 mm interval apart (the patent's plan view): both T-nuts go into one slot, as the MVG's do. A configurator site says two slots, unattributed; Magpul's sheet names no count.
Reach inside the handguard (below the mounting face, tightened)No value yetMissingNo source yet
Not sourced (as for the MVG: Magpul publishes no T-nut figure).
Mounting face: the band between the ears, below the ears' tips0.116 in ± 0.01 in 2.9 mmProvisionalPhoto: US D755,333 S (Magpul, 'Hand stop for a firearm'), FIG. 3 front elevation, 300 dpi
Photo 0.116 in ± 0.01 in used
US D755,333 S (Magpul, 'Hand stop for a firearm'), FIG. 3 front elevation, 300 dpi, harvested
Scale: the traced front elevation's own scale (profiles.front: magpul-mlok-hand-stop.height and .width, 1288.7 px/in). Read by the flat between the ears on the traced outline, at y 0.116 from z -0.348 to +0.350, against the ears' tips at y 0 (z ±0.52)
The band is what bears on a handguard's M-LOK face (2026-10-05, the model review: seated on its ears' tips it touched nothing on the 22RB's bottom flat, 0.12 to 0.17 in of air everywhere). Its ears slope out and up from the band's edges, 0.17 in across and this high: they run down either side of a face narrower than the band, as every M-LOK face on file is. On a flat wider than the ears' tips (1.05 in) the tips would bear instead.
Mounting face: the band between the ears, across0.698 in ± 0.02 in 17.7 mmProvisionalPhoto: US D755,333 S (Magpul, 'Hand stop for a firearm'), FIG. 3 front elevation, 300 dpi
Photo 0.698 in ± 0.02 in used
US D755,333 S (Magpul, 'Hand stop for a firearm'), FIG. 3 front elevation, 300 dpi, harvested
Scale: the traced front elevation's own scale (profiles.front, 1288.7 px/in). Read by the flat between the ears on the traced outline: z -0.348 to +0.350
Rear lug's centre ahead of the part's rear end0.374 in ± 0.02 in 9.5 mmProvisionalPhoto: US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi
Photo 0.374 in ± 0.02 in used
US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi, harvested
Scale: the plan view's own length, 2038 px, as the plate's length (.length, 1.575 in). Read by the lip-end screw hole's centre, 484 px from the plate's lip end (the tail-end one is 528 px from the tail, the two 1026 px apart); by eye on a half-size crop, ± 6 px
From the patent's plan view: the screw at the hook's end, which is the part's rear (2026-10-05: the part's frame was turned end for end, its hook to the rear as Magpul pictures it; until then this was the tail-end screw, 0.408 from the tail). The tail-end screw is 0.408 in from the front end, and the two 0.793 apart (20.1 mm).
Screw hole (through the plate)0.22 in ± 0.008 in 5.6 mmProvisionalPhoto: US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi
Photo 0.22 in ± 0.008 in used
US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi, harvested
Scale: the plan view's own length, 2038 px, as the plate's length (.length, 1.575 in): 1294.0 px/in. Read by the innermost of the five broken-line circles round the plate's screw, fitted on one centre: radius 142.6 px (a second, 155.6 px, is drawn 13 px outside it). The index panel's hole is 0.219 in on its own drawing
Screw's recess in the outer face, at its rim0.399 in ± 0.008 in 10.1 mmProvisionalPhoto: US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi
Photo 0.399 in ± 0.008 in used
US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi, harvested
Scale: the plan view's own length, 2038 px, as the plate's length (.length, 1.575 in): 1294.0 px/in. Read by the outermost of the five broken-line circles, fitted: radius 257.9 px (the next in, 244.3 px, 0.378 in)
FIG. 8's outermost circle here; the index panel's own drawing has one more outside it (0.429 in). How deep the recess is no view gives.
Screw's recess in the outer face, the innermost of its three circles0.358 in ± 0.008 in 9.1 mmProvisionalPhoto: US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi
Photo 0.358 in ± 0.008 in used
US D755,333 S, Magpul, FIG. 8 bottom plan; the patent office's copy, page 10, 300 dpi, harvested
Scale: the plan view's own length, 2038 px, as the plate's length (.length, 1.575 in): 1294.0 px/in. Read by the third circle out from the centre, fitted: radius 231.3 px. The index panel's is 0.360 in on its own drawing: the same dish for the same screw
Screw's head, across0.375 in ± 0.025 in 9.5 mmProvisionalPhoto: Magpul's gallery for MAG608, mag608_fde_2.png, 1200 x 1200: the FDE kit's pieces put together with their screws in, three-quarter from the outer side
Photo 0.375 in ± 0.025 in used
Magpul's gallery for MAG608, mag608_fde_2.png, 1200 x 1200: the FDE kit's pieces put together with their screws in, three-quarter from the outer side, harvested
Scale: the recess's rim in the same view, as .screw_recess_diameter (0.399 in): both are circles on one axis a few hundredths of an inch apart in depth, so their long axes are in the ratio of their diameters. Read by the dark head's long axis 56.8 px (columns 652 to 710 at luminance under 75) against the rim's 60.5 px, read on a tenfold enlargement; ± covers a pixel and a half on each and the rim's soft edge
Magpul publishes no figure for the kit's screws. A wide low head with a six-lobe socket (Wing Tactical's photo of the kit's hardware: six alike). The index panel's, read the same way on the same picture, is 0.364 in.
Screw's head: its crown above the plate's outer face0.033 in ± 0.008 in 0.8 mmProvisionalPhoto: Supplied in chat 2026-10-02: a gallery image of an M-LOK handguard, straight side view, the hand stop and the index panel installed, rail teeth along the top, 2796 x 1290
Photo 0.033 in ± 0.008 in used
Supplied in chat 2026-10-02: a gallery image of an M-LOK handguard, straight side view, the hand stop and the index panel installed, rail teeth along the top, 2796 x 1290, from the site owner
Scale: the handguard's rail teeth in the same image: 336.5 px/in. Read by the plate's outer face at half tone on its smooth stretch behind the screw (rows 785.1 to 786.4, u 1136 to 1208) to the head's lowest point (row 796.8, u 1080 to 1096): 11.0 px; ± covers 2 px and the face's own 1.3 px
A rendering whose source page isn't on file (the ledger's header); the index panel's screw reads 0.034 in on the same image.
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
M-LOK
- Uppers
- Nordic Components 22RB .22 LR upper, 16" (fit unchecked), Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12" (fit unchecked), Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16" (fit unchecked)
- Handguards
- Aero Precision AR15 10.3" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 12.7" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 15" Enhanced M-LOK Handguard, Gen 2 (fit unchecked), Aero Precision AR15 15" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 15" S-ONE M-LOK Handguard (fit unchecked), Aero Precision AR15 16.6" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 7.3" R-ONE M-LOK handguard (fit unchecked), Aero Precision AR15 9.3" R-ONE M-LOK handguard (fit unchecked), BCM MCMR-10 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM MCMR-13 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM MCMR-15 (M-LOK® Compatible* Modular Rail) (fit unchecked), BCM PMCR (Polymer M-LOK® Compatible Rail)* Carbine Length-BLACK (fit unchecked), BCM PMCR (Polymer M-LOK® Compatible Rail)* Mid Length-BLACK (fit unchecked), Expo Arms Free Float AR-15 Handguard - M-LOK - 15" (fit unchecked), Geissele Automatics 10.5" Super Modular Rail MK16 M-LOK (fit unchecked), Geissele Automatics 13.5" Super Modular Rail MK16 M-LOK (fit unchecked), Geissele Automatics 15" Super Modular Rail MK16 M-LOK (fit unchecked), Magpul MOE SL® Hand Guard, Carbine-Length – AR15/M4 (fit unchecked), Magpul MOE SL® Hand Guard, Mid-Length – AR15/M4 (fit unchecked), Magpul MOE® M-LOK® Hand Guard, Carbine-Length – AR15/M4 (fit unchecked), Magpul MOE® M-LOK® Hand Guard, Mid-Length – AR15/M4 (fit unchecked), MAS Defense 12.62" NERO M-LOK FREE FLOAT (fit unchecked), MAS Defense 15" NERO M-LOK FREE FLOAT (fit unchecked), MAS Defense 9.87" NERO M-LOK FREE FLOAT (fit unchecked), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Carbine) (fit unchecked), Midwest Industries AR-15/M16 Two Piece Drop-In Handguard, M-LOK® (Mid-Length) (fit unchecked), Midwest Industries Combat Rail One Piece Free Float Handguard, M-LOK™ (15") (fit unchecked)
- Adapter plates
- Magpul M-LOK Hand Stop MOE Adapter (fit unchecked)