Barrel
BCM Standard 11.5" Carbine Barrel, Stripped
Bravo Company's 11.5 in government-profile barrel, stripped: MIL-B-11595E chrome moly vanadium steel, a chrome lined 5.56 NATO chamber and bore, 1/7 twist, manganese phosphate, a carbine-length gas port drilled and dimpled on a .750 in journal, an M4 feed ramp extension, a 1/2-28 muzzle thread.

- Weight
- 21 oz ± 1 oz Confirmedpublished: BCM, BCM Standard 11.5" Carbine Barrel, Stripped (BCM-BRL-s-11-STD), Description, the maker, read Oct 6, 2026
- Lowest price
- $279.00 at BCM, read Nov 21, 2026, out of stock that day
- Made for
- 5.56 NATO Chambers
- Maker's number
- BCM-BRL-s-11-STD
- Colour
- Manganese phosphate, charcoal
- Drawn as
- modelled
- Maker's page
- bravocompanyusa.com
In “BCM 11.5 in carbine, suppressed”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Barrel length as its maker states it11.5 in ± 0.05 in 292.1 mmConfirmedPublished: BCM, BCM Standard 11.5" Carbine Barrel, Stripped (BCM-BRL-s-11-STD), Description, the maker, read Oct 6, 2026
Published “These are stripped 11.5" carbine gas Standard 11595E barrels with gas ports installed and dimpled for a strong gas block installation.” used
BCM, BCM Standard 11.5" Carbine Barrel, Stripped (BCM-BRL-s-11-STD), Description, the maker, read Oct 6, 2026 the page, harvested Oct 6, 2026
Published “Barrel Length 11.5”
Primary Arms, Bravo Company Manufacturing Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 11.5" (BCM-BRL-S-11-STD), Specifications, a seller, read Oct 6, 2026 the page, harvested Oct 6, 2026
The maker's own; the seller repeats it.
The nominal length. BCM's page doesn't say between which points; the Army's barrel drawing (8448549) dimensions a barrel from its breech end, inside the extension, to its muzzle, and overall_length takes it so.
The gas block journal's diameter0.75 in ± 0.0005 in 19 mmConfirmedPublished: BCM, BCM Standard 11.5" Carbine Barrel, Stripped (BCM-BRL-s-11-STD), Description, the maker, read Oct 6, 2026
Published “(.750) at Gas Block location” used
BCM, BCM Standard 11.5" Carbine Barrel, Stripped (BCM-BRL-s-11-STD), Description, the maker, read Oct 6, 2026 the page, harvested Oct 6, 2026
Published “Gas Seat Diameter .750”
Primary Arms, Bravo Company Manufacturing Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 11.5" (BCM-BRL-S-11-STD), Specifications, a seller, read Oct 6, 2026 the page, harvested Oct 6, 2026
The maker's own; the seller repeats it.
The barrel extension's rear end behind the barrel's breech end0.501 in ± 0.01 in 12.7 mmProvisionalWorked out: {std.ar15.barrel_extension_behind_breech}
Worked out 0.501 in ± 0.01 in used
{std.ar15.barrel_extension_behind_breech}, from the site owner
The standard's: the reference CAD set's extension less the Army's .620 tenon (std.ar15.barrel_extension_behind_breech), the one figure the catalog's 5.56 barrels take their breech from. BCM: "M4 Feed Ramp Barrel Extension".
End to end, the extension's rear to the muzzle12.001 in ± 0.07 in 304.8 mmConflictWorked out: {.length} + {.extension_behind_breech}
Photo 12.2 in ± 0.05 in
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: its extension's body as the Army's .999 (extension_od) and its journal as the published .750 (journal_od). Read by its two end faces, each behind its rim's arc (columns 104.2 and 2101.8: outline_rear_face, outline_front_face), at the scales its extension's body and its journal give with their edges read at grey 200 and no allowance for the cut-out's edge (164.49 px/in at column 175, 163.44 at 1577, a straight line between and beyond)
Photo 12.05 in ± 0.06 in
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: its muzzle thread's pitch as 28 to the inch (thread_pitch), with its extension's body and its journal. Read by the same two faces, with the thread as the ruler: the calibration fixed by the two diameters and by 28 threads to the inch at the muzzle (5.905 px a thread on rows just inside each edge, columns 2008 to 2090; the spectrum's peak, 5.87 to 5.93 by the row) in place of the published length
Worked out 12.001 in ± 0.07 in used
{.length} + {.extension_behind_breech}, harvested
The maker's length: the site's line on the law goes by it, and the photo's calibration is fixed by it. The thread's pitch, which doesn't use it, agrees within 0.4%; the two diameters with their edges as read are 1.7% longer, by the cut-out's edge.
photo and thread differ by 0.15 in beyond what each states it is good to.
photo and published differ by 0.199 in beyond what each states it is good to.
The published length is the scale for lengths: it is one of the three knowns the photo's calibration is fixed by, with the extension's body (the Army's .999) and the journal (.750). The two diameters alone, their edges read at grey 200, have the barrel 1.7% longer (the 14.5 in barrel's photo reads 1.5% longer the same way, the 16 in barrel's 2.5%: a black tube reads thin on white); what closes it is 1.09 px on each edge, a cut-out's width. The checks that are not among the three: the thread's own pitch as the ruler has the barrel 12.05 (the second measurement here: 0.4% from the published one), the plain relief behind the thread comes out at 0.496 (the Army's crests .4957), the indexing pin at 0.127 across (the reference CAD set's .125), the flange at 1.176 (1.170), the extension 0.990 long behind its flange (0.990), the thread 0.62 long from the shoulder (the Army's .63), and the gas port 1.96 and 1.99 behind its two mid-length siblings'. The ± of the published one covers whether the 11.5 is from the barrel's breech end (the Army's drawing) or from the bolt's face, an eighth further back.
The barrel extension's rear end, from the flange's rear face (negative: inside the receiver)-0.99 in ± 0.02 in -25.1 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo -0.99 in ± 0.02 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.8 px/in along the axis there. Read by the rear end's face (column 104.2: outline_rear_face, behind its rim's arc of 7.5 px) to the flange's rear face (column 269.5): where the flange's lower edge reaches its full depth, up its rim's near arc (7.4 px deep, seen for 4 px; the pin hides the upper edge there)
The reference CAD set's extension has 0.990 here (1.121 less its 0.131 flange); the 16 in barrel's own photo 0.984, the 14.5 in barrel's 0.984.
The extension flange's front face, ahead of its rear face (the flange's thickness)0.114 in ± 0.015 in 2.9 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 0.114 in ± 0.015 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.8 px/in along the axis there. Read by the flange's rear face (column 269.5) to where its edges stop being level (column 288.5)
The reference CAD set's flange is 0.131 thick; this one reads thinner, as its two siblings' did by their own photos (0.095 and 0.102).
The barrel extension's flange, its diameter1.176 in ± 0.01 in 29.9 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 1.176 in ± 0.01 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.65 px/in there. Read by the silhouette's widest, columns 272 to 287: 193.8 px, with the cut-out's 2.18 px
The reference CAD set's is 1.170. (flange_od is this same height at the journal's scale alone, the outline's scale reference.)
The barrel extension's body, its diameter (what goes into the receiver)0.999 in ± 0.001 in 25.4 mmConfirmedStandard: US Army TDP drawing 8448548 (Barrel and Barrel Extension Assembly), rev N: the assembly's side view at 1/1; user-supplied scan, PDF page 212
Standard “DIAMETER NOT TO EXCEED .9990 FOR THIS LENGTH AFTER ASSEMBLY AND BEFORE FINISH” used
US Army TDP drawing 8448548 (Barrel and Barrel Extension Assembly), rev N: the assembly's side view at 1/1; user-supplied scan, PDF page 212, from the site owner
An upper limit: it goes into the receiver's 1.000 bore (8448524). The reference CAD set's extension is .9987.
Photo 1.005 in ± 0.006 in
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: its gas block journal's diameter as the published .750 (journal_od): 163.44 px/in. Read by the extension's body, columns 115 to 235: 164.33 px against the journal's 122.58 (a line through each edge at grey 200)
The drawing's limit: an extension over 1.000 doesn't go into a receiver. The photo reads 0.5% large here because its breech end is nearer the lens than its journal.
The photo's reading says how square the photo is, not how big the extension is: at the journal's scale it is 0.5% large, the breech end standing a little nearer the lens than the journal. It is one of the three knowns the photo's calibration is fixed by (with the journal's .750 and the published length), so the model draws it at the drawing's.
The chamber section's diameter (between the flange and the taper)0.981 in ± 0.01 in 24.9 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 0.981 in ± 0.01 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.63 px/in there. Read by columns 310 to 392: 161.33 px (a line through each edge at grey 200), with the cut-out's 2.18 px
The 14.5 in barrel's reads .980 by its own photo.
Where the taper ahead of the chamber section begins, ahead of the extension's face0.77 in ± 0.025 in 19.6 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 0.77 in ± 0.025 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.8 px/in along the axis there. Read by the flange's rear face (column 269.5) to where the straight taper's edges, carried back, meet the chamber section's (column 398)
Where the taper ends and the section under the handguard begins, ahead of the extension's face1.631 in ± 0.025 in 41.4 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 1.631 in ± 0.025 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.7 px/in along the axis there. Read by the flange's rear face (column 269.5) to where the taper's edges meet the section's ahead (column 541.5)
A straight cone: its edges are lines from column 405 to 540.
The section under the handguard, its diameter at its rear end (the taper's foot)0.679 in ± 0.008 in 17.2 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 0.679 in ± 0.008 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.59 px/in there. Read by a line through each edge over columns 560 to 900, carried to column 545: 111.0 px, with the cut-out's 2.18 px
The section narrows toward the muzzle as far as handguard_knee_x and is level from there to the ramp.
Where the section under the handguard stops narrowing, ahead of the extension's face5.22 in ± 0.3 in 132.6 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 5.22 in ± 0.3 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.4 px/in along the axis there. Read by the flange's rear face (column 269.5) to column 1140, where the lines through the narrowing stretch (columns 560 to 1100) reach the level stretch's width (106.7 px)
The edges close by 0.0073 px a column from column 545 and are level within a fifth of a pixel from about column 1140 to the ramp: where one becomes the other is good to a third of an inch.
The section under the handguard, its diameter over its level front end (to where the ramp to the collar begins)0.654 in ± 0.008 in 16.6 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 0.654 in ± 0.008 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.43 px/in there. Read by columns 1147 to 1231: 106.7 px, with the cut-out's 2.18 px
Where the ramp up to the collar begins, ahead of the extension's face5.777 in ± 0.03 in 146.7 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 5.777 in ± 0.03 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.4 px/in along the axis there. Read by the flange's rear face (column 269.5) to where the edges leave the section's line (column 1232)
A concave ramp, steepening to a sharp corner at the collar's full diameter.
A station midway up the ramp, ahead of the extension's face6.017 in ± 0.02 in 152.8 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 6.017 in ± 0.02 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.4 px/in along the axis there. Read by the flange's rear face (column 269.5) to column 1272
With ramp_mid_od: the third point the model's arc is put through.
The ramp's diameter at that station0.713 in ± 0.01 in 18.1 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 0.713 in ± 0.01 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.41 px/in there. Read by column 1272: 116.52 px, with the cut-out's 2.18 px
Where the collar reaches its full diameter (the ramp's top), ahead of the extension's face6.254 in ± 0.02 in 158.9 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 6.254 in ± 0.02 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.4 px/in along the axis there. Read by the flange's rear face (column 269.5) to where the edges become level (column 1311.5)
The collar behind the gas block journal, its diameter0.855 in ± 0.008 in 21.7 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 0.855 in ± 0.008 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.39 px/in there. Read by columns 1320 to 1400: 140.05 px (a line through each edge at grey 200), with the cut-out's 2.18 px
What a gas block's rear face comes back to. The 14.5 in barrel's reads .854 by its own photo, the 16 in barrel's 0.86.
The chamfer on the collar's front corner (along the barrel; as much down the face: 45 degrees)0.037 in ± 0.01 in 0.9 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 0.037 in ± 0.01 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.3 px/in along the axis there. Read by where the collar's edges begin to fall (column 1409) to its front face (column 1415.2): 6.2 px; the edge is 5.5 px lower at the face (64.6 px of radius against 70.1)
The edges fall 5.5 px toward the axis over the 6.2 px before the face: as much down as along, within a pixel. Primary Arms' close view of the journal (2583fd18e700) shows it as a lighter band round the collar's rim.
The gas block journal's rear shoulder (the collar's front face) ahead of the extension's face6.878 in ± 0.02 in 174.7 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 6.878 in ± 0.02 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.3 px/in along the axis there. Read by the flange's rear face (column 269.5) to the collar's front face (column 1415.2): where its edges drop to the groove's, 0.8 px before the drop's end at column 1416 (the face's rim, 65 px in radius under the chamfer, is an arc 1.9 px deep from this far, seen past the groove for 0.8)
A gas block's rear face comes back to this shoulder. The collar's corner is cut off behind it (collar_chamfer); the relief groove begins at it.
The relief groove at the collar's front face, its front wall ahead of the extension's face6.923 in ± 0.02 in 175.8 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 6.923 in ± 0.02 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.3 px/in along the axis there. Read by the flange's rear face (column 269.5) to where the edges are back up at the journal's (column 1422.7)
A groove 0.045 in wide between the collar's face and the journal, on the silhouette here; Primary Arms' close view of the journal (2583fd18e700) shows it as a dark band with a bright rim.
The relief groove's diameter at its floor0.725 in ± 0.008 in 18.4 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 0.725 in ± 0.008 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.38 px/in there. Read by columns 1417 to 1421: 118.5 px (118.0 to 118.9), with the cut-out's 2.18 px
0.013 in under the journal's surface on each side. The lens's blur fills a groove 7 px wide a little: it may be deeper.
The gas port ahead of the extension's face7.138 in ± 0.03 in 181.3 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 7.138 in ± 0.03 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.3 px/in along the axis there. Read by the flange's rear face (column 269.5) to the port (column 1458.5: between the middle of its mouth's dip in the upper edge and the middle of the dimple's dent in the lower)
BCM says "gas ports installed and dimpled" and gives no distance. The port is on top in this photo, in line with the indexing pin: its mouth dips the upper edge by a fifth of a pixel over columns 1448 to 1463, and the dimple opposite it dents the lower edge by 0.65 px over columns 1448 to 1471. The dent is the surer of the two: the port is put three parts toward its middle (column 1459.5) from the dip's (1455.5). That is 0.26 ahead of the journal's rear shoulder (the 14.5 in barrel's own photo has 0.29, the 16 in barrel's 0.28; 8448548 has .295 on the rifle's barrel; BCM's own gas block has its port 0.275 ahead of its rear face), and 1.96 behind the 14.5 in barrel's mid-length port and 1.99 behind the 16 in barrel's: a carbine-length gas tube is 2 in shorter than a mid-length one. A second look: in Primary Arms' close view of the journal (2583fd18e700) the port's middle is 3.85 of its own mouth's lengths ahead of the collar's face along the barrel, 0.27 to 0.30 for a port of .070 to .078.
The dimple under the journal opposite the gas port, its width along the barrel0.144 in ± 0.015 in 3.7 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 0.144 in ± 0.015 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.3 px/in along the axis there. Read by the dent in the lower edge, columns 1448 to 1471: 24 px
BCM: "gas ports installed and dimpled for a strong gas block installation". Its depth isn't shown: the silhouette's dent (0.65 px) is only the chord its rim cuts across the journal's underside, which a dimple this wide and deeper than 0.007 in would make 1.2 px. Not drawn.
The gas block journal's front end (where the barrel steps down) ahead of the extension's face8.803 in ± 0.02 in 223.6 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 8.803 in ± 0.02 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.2 px/in along the axis there. Read by the flange's rear face (column 269.5) to the journal's front face (column 1735.2): where its edges drop, a pixel before the drop's end; its corner is broken over the 4 px before
The journal is 1.93 long, as the 14.5 in barrel's is by its own photo: long enough for a front sight base's two bands.
The diameter ahead of the journal (between its front end and the step behind the muzzle)0.726 in ± 0.008 in 18.4 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 0.726 in ± 0.008 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.28 px/in there. Read by columns 1752 to 1885: 118.58 px (a line through each edge at grey 200), with the cut-out's 2.18 px
The 14.5 in barrel's reads .718 by its own photo.
The step behind the muzzle (where the last section begins) ahead of the extension's face9.813 in ± 0.02 in 249.3 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 9.813 in ± 0.02 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.1 px/in along the axis there. Read by the flange's rear face (column 269.5) to the step's face (column 1903): where the edges drop, a pixel before the drop's end
The diameter behind the muzzle thread0.699 in ± 0.008 in 17.8 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 0.699 in ± 0.008 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.25 px/in there. Read by columns 1912 to 1985: 114.1 px (a line through each edge at grey 200), with the cut-out's 2.18 px
The last section before the shoulder, 0.57 long. The 14.5 in barrel's reads .700 by its own photo.
The chamfer on the muzzle shoulder's corner (along the barrel; as much down the face: 45 degrees)0.035 in ± 0.01 in 0.9 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 0.035 in ± 0.01 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.0 px/in along the axis there. Read by where the last section's edges begin to fall (column 1992.5) to the shoulder's face (column 1998.3): 5.8 px; the edge is 5.7 px lower at the face (51.4 px of radius against 57.1)
The edges fall 5.7 px toward the axis over the 5.8 px before the face. Primary Arms' close view of the muzzle (798114485812) shows it as a lighter band round the shoulder's rim. The 14.5 in barrel's level photo, taken from close by, fits a shoulder with none or little.
The muzzle shoulder ahead of the extension's face10.387 in ± 0.02 in 263.8 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 10.387 in ± 0.02 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.0 px/in along the axis there. Read by the flange's rear face (column 269.5) to the shoulder's face (column 1998.3): 2.7 px before the edges reach the relief's (column 2001), where the arc of its rim (51.4 px in radius under the chamfer) ends
Where the thread begins: a muzzle device or its washer seats here. Its corner is cut off (shoulder_chamfer), and past the face the silhouette is the face's rim, an arc 4.3 px deep from this far, seen past the relief for 2.7 px. Ahead of it a plain relief the thread's size, 0.06 long, before the first turn.
The muzzle thread's length0.624 in ± 0.025 in 15.8 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 0.624 in ± 0.025 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.0 px/in along the axis there. Read by the shoulder's face (column 1998.3) to the muzzle's face (column 2101.8: outline_front_face, behind its rim's arc and its crown's break)
From the shoulder to the muzzle's face, the relief behind the first turn included: the Army's .63 (8448549 sheet 1; a mid-length chart has .624). The 14.5 in barrel's own photo reads 0.61. The thread's own pitch reads 5.905 px here (rows just inside each edge, columns 2008 to 2090), which is 28 to the inch at 165.3 px/in where the calibration has 166.0: the thread as the ruler agrees within 0.4%.
The plain relief between the shoulder and the thread's first turn, its diameter0.496 in ± 0.008 in 12.6 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 0.496 in ± 0.008 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.24 px/in there. Read by columns 2002 to 2007: 80.3 px, with the cut-out's 2.18 px
The thread's blank, unthreaded for 0.06 in ahead of the shoulder: it reads the Army thread's major diameter (.4957), a check of the calibration at the muzzle. Not drawn as such: the model's thread runs out there.
The barrel indexing pin's axis behind the flange's rear face0.081 in ± 0.012 in 2.1 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 0.081 in ± 0.012 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.9 px/in along the axis there. Read by the pin on the upper edge (columns 246.5 to 265.5: its middle at 256) to the flange's rear face (column 269.5)
The pin is on the upper edge in this photo. The reference CAD set has 0.0765 (0.2075 behind the flange's front face, less its 0.131 flange); the 14.5 in barrel's own photo 0.086, the 16 in barrel's 0.113.
The barrel indexing pin's top above the bore's axis0.594 in ± 0.008 in 15.1 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 0.594 in ± 0.008 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the photo's calibration (outline_lens_x, outline_yaw_run, outline_inset: a diameter's scale 166.45 px/in opposite the lens at column 1100 and 0.24 px/in less per 1000 px toward the muzzle, the cut-out's edge 1.09 px inside the barrel's); 166.65 px/in there. Read by the pin's top on the upper edge, columns 250 to 263: 97.9 px above the axis, with the cut-out's 1.09 px
A hair over the flange's rim (0.588): the 16 in barrel's own photo has its pin a hair under its flange's (0.584 against 0.5925).
The photo's calibration: the lens's foot along the traced outline (in the outline's own frame, from the silhouette's rear tip)6.134 in ± 0.5 in 155.8 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 6.134 in ± 0.5 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the traced outline's own (flange_od): 163.6 px/in. Read by column 1100 of 2200, in the outline's unit (163.6 px/in from its tip at column 96.7)
The picture's middle, taken as that: from this far (the rear end's rim is an arc 7.5 px deep on a radius of 82: the lens about 65 in off) a step's rim is an arc of 2 to 5 px, and where the lens's foot lies moves nothing by more than a few thousandths.
The photo's calibration: how fast its scale changes toward the muzzle (the scale is 1 + (x - outline_lens_x) / this, x along the traced outline; negative: smaller at the muzzle)-4310 in ± 1500 in -109474 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo -4310 in ± 1500 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: its extension's body (extension_od) and its journal (journal_od). Read by the extension's body (164.33 px at column 175) as the Army's .999 and the journal (122.58 px at column 1577) as the published .750, each with the cut-out's 2.18 px: 166.67 and 166.34 px/in, 1402 px apart
The barrel leans 0.9 degrees to the lens, its breech nearer: the extension's body reads 0.5% large against the journal. A lean changes a diameter's scale in a straight line along the picture, and a length's twice as fast (a point of the axis at x is (x - outline_lens_x) / scale from the lens's foot). The scale falls 0.28% from the rear face to the muzzle.
The photo's calibration: how far inside the barrel's edge the cut-out's edge at grey 200 stands, on each side (in the outline's unit)0.007 in ± 0.003 in 0.2 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 0.0067 in ± 0.003 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: its extension's body (extension_od), its journal (journal_od) and its published length (overall_length). Read by solved: the length between the end faces (columns 104.2 and 2101.8) at the scales the extension's body and the journal give is 12.001 with 2.18 px added to every width, 12.196 with none
1.09 px. What makes the two known diameters' scales give the published length between the end faces (overall_length); with none, the barrel reads 12.2. The thread's pitch, read apart from it, has the same scale within 0.4%.
The barrel extension's flange, its diameter as the photo has it at the journal's scale1.186 in ± 0.008 in 30.1 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 1.186 in ± 0.008 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: its gas block journal's diameter, 122.58 px (columns 1432 to 1722, a line through each edge at grey 200), as the published .750 (journal_od): 163.44 px/in. Read by the silhouette's widest, columns 272 to 287: 193.8 px against the journal's 122.58
The scale reference of the traced outline (the silhouette's greatest height), which sets the outline's unit to the journal's own. It is not quite the flange's size (flange_d): the photo's breech end stands a little nearer the lens than its journal (extension_od), and its cut-out edge is inside the barrel's (outline_inset).
The bore's diameter (across the lands)0.219 in ± 0.001 in 5.6 mmConfirmedStandard: US Army TDP drawing 8448549 (Barrel), sheet 2 of 2, rev J: Section U-U, rifling detail at 10/1; user-supplied scan, PDF page 211
Standard “.219 DIA+.001” used
US Army TDP drawing 8448549 (Barrel), sheet 2 of 2, rev J: Section U-U, rifling detail at 10/1; user-supplied scan, PDF page 211, from the site owner
The muzzle thread's major diameter (its crests)0.496 in ± 0.0033 in 12.6 mmConfirmedStandard: US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213
Standard “1/2-28 UNEF-2A MAJOR DIA .4989/.4924” used
US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213, from the site owner
The Army barrel's 1/2-28 thread, for the 1/2 X 28 the seller states: what the model's thread is drawn at.
The muzzle thread's minor diameter (its roots)0.455 in ± 0.002 in 11.6 mmConfirmedStandard: US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213
Standard “MINOR DIA .4551 MAX” used
US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213, from the site owner
The muzzle thread's pitch0.036 in ± 0.00005 in 0.9 mmCorroboratedPublished: Primary Arms, Bravo Company Manufacturing Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 11.5" (BCM-BRL-S-11-STD), Specifications, a seller, read Oct 6, 2026
Standard “1/2-28 UNEF-2A”
US Army TDP drawing 8448549 (Barrel), sheet 1 of 2, rev J: Section M-M, the muzzle's thread; user-supplied scan, PDF page 213, from the site owner
Published “Thread Pattern 1/2 X 28” used
Primary Arms, Bravo Company Manufacturing Chrome Lined 5.56 AR-15 Barrel - Carbine - Government - 11.5" (BCM-BRL-S-11-STD), Specifications, a seller, read Oct 6, 2026 the page, harvested Oct 6, 2026
The seller's statement for this barrel; the Army's drawing has the same thread on its own.
28 threads to the inch, by the seller's statement and the Army barrel's drawing: neither is a measurement of this barrel.
The gas port's diameter0.078 in ± 0.012 in 2 mmCorroboratedPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_03: the gas block journal from above, close, 2200 x 1467
Photo 0.078 in ± 0.012 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_03: the gas block journal from above, close, 2200 x 1467, harvested
Scale: the journal's width across the barrel beside the port as the published .750 (journal_od): about 390 px, 520 px/in. Read by the port's mouth, an ellipse 41 px long along the barrel by 28 across (columns 1107 to 1148, rows 715 to 750): its long axis, which the view doesn't shorten
Published “0.075"ø Gas Port”
AR-15_M4_Barrel_Dimensions.jpg in the user's TDP folder (Spec_Sheets): a third-party illustration of a 14.5 in mid-length barrel, no drawing number, a page, from the site owner
This barrel's own port, on its own photo; the chart's is another length of gas system's, and agrees within the reading.
BCM publishes none, and no drawing of a carbine's port is in the package. Read on Primary Arms' close view of this barrel's journal, a little oblique; a chart's figure for a mid-length barrel is beside it (the rifle's, 8448548, is .092).
The barrel indexing pin's diameter0.125 in ± 0.002 in 3.2 mmProvisionalWorked out: {bcm-16-mid-barrel.index_pin_d}
Worked out 0.125 in ± 0.002 in used
{bcm-16-mid-barrel.index_pin_d}, from the site owner
A mil-spec extension's, as bcm-16-mid-barrel's ledger read it off the reference CAD set (BCM, of this barrel: "M4 Feed Ramp Barrel Extension"; of the 16 in one: "M4 Feed Ramp Barrel Extension (USGI)").
The barrel extension's rear opening, its diameter at the rear face0.77 in ± 0.005 in 19.6 mmProvisionalWorked out: {bcm-16-mid-barrel.extension_mouth_d}
Worked out 0.77 in ± 0.005 in used
{bcm-16-mid-barrel.extension_mouth_d}, from the site owner
The inside of a mil-spec extension as the reference CAD set has it, read once in bcm-16-mid-barrel's ledger (BCM, of this barrel: "M4 Feed Ramp Barrel Extension"; of the 16 in one: "M4 Feed Ramp Barrel Extension (USGI)"). Appearance only.
The rear opening's chamfer, its depth (at 45°, also how far it narrows the opening's radius)0.045 in ± 0.005 in 1.1 mmProvisionalWorked out: {bcm-16-mid-barrel.extension_mouth_chamfer}
Worked out 0.045 in ± 0.005 in used
{bcm-16-mid-barrel.extension_mouth_chamfer}, from the site owner
The circle the extension's locking lugs leave between their tips0.572 in ± 0.003 in 14.5 mmProvisionalWorked out: {bcm-16-mid-barrel.extension_lug_bore_d}
Worked out 0.572 in ± 0.003 in used
{bcm-16-mid-barrel.extension_lug_bore_d}, from the site owner
The locking lugs' front faces, ahead of the extension's rear end0.214 in ± 0.005 in 5.4 mmProvisionalWorked out: {bcm-16-mid-barrel.extension_lug_depth}
Worked out 0.214 in ± 0.005 in used
{bcm-16-mid-barrel.extension_lug_depth}, from the site owner
The recess ahead of the lugs, which the bolt's lugs turn in: its diameter0.83 in ± 0.003 in 21.1 mmProvisionalWorked out: {bcm-16-mid-barrel.extension_recess_d}
Worked out 0.83 in ± 0.003 in used
{bcm-16-mid-barrel.extension_recess_d}, from the site owner
The recess's front end, ahead of the extension's rear end0.595 in ± 0.005 in 15.1 mmProvisionalWorked out: {bcm-16-mid-barrel.extension_recess_depth}
Worked out 0.595 in ± 0.005 in used
{bcm-16-mid-barrel.extension_recess_depth}, from the site owner
The extension's rear face in the traced outline's own frame (from the silhouette's rear tip, at the journal's scale)0.046 in ± 0.009 in 1.2 mmProvisionalPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, 2200 x 1467
Photo 0.046 in ± 0.009 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, 2200 x 1467, harvested
Scale: scale from bcm-115-carbine-barrel.flange_od = 1.186 in (y-extent 194 px → 163.6 px/in). Read by the min end's face: the silhouette's tip at -0.000 less its rim's arc, 0.046 in of sag at radius 0.497451 (the end is seen from 5.3° off square; arc fitted over 113 rows, rms 0.002) of the traced outline (tools/trace.py); the extension's rear face in the outline's own frame (from its rear tip, at the journal's scale)
Where the outline is cut: the silhouette's tip is the rear rim's near side, which stands behind the face by the rim's arc.
The muzzle's face in the traced outline's own frame (from the silhouette's rear tip, at the journal's scale)12.258 in ± 0.012 in 311.4 mmCorroboratedPhoto: Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467
Photo 12.24 in ± 0.083 in
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, 2200 x 1467, harvested
Scale: scale from bcm-115-carbine-barrel.flange_od = 1.186 in (y-extent 194 px → 163.6 px/in). Read by the max end's face: the silhouette's tip at 12.278 less its rim's arc, 0.038 in of sag at radius 0.228863 (the end is seen from 9.4° off square; arc fitted over 118 rows, rms 0.002) of the traced outline (tools/trace.py); the muzzle's face in the outline's own frame (from its rear tip, at the journal's scale)
Photo 12.258 in ± 0.012 in used
Primary Arms' gallery, BCM-BRL-S-11-STD_01: the barrel from the side on white, the muzzle at the right, 2200 x 1467, harvested
Scale: the traced outline's own (flange_od): 163.6 px/in. Read by the silhouette's tip (12.278) less the arc the face's own rim makes: the crown's corner is broken (the thread's edges leave their full height 8 px before the tip, where a rim of the thread's radius seen from 5.3 degrees would take 3.7), so the face's rim is 35 px in radius and its arc 3.2 px deep, the lens 65 in off as the rear end's arc has it
The tool fits one arc of the thread's own radius to the muzzle's rim and its broken corner together, and puts the face 0.02 in too far back (it has the muzzle seen from 9.4 degrees where the rear end, as far from the lens's foot, is seen from 5.3); the rim's own arc, at the lens's distance as the rear end gives it, is the face. The thread is then 0.63 in long, the Army's.
Where the outline is cut: the silhouette's front tip is the muzzle rim's near side.
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Barrel extension
- Uppers
- Aero Precision M4E1 Enhanced Upper Receiver Stripped, Aero Precision M4E1 Threaded upper receiver, BCM M4 Upper Receiver Assembly (w/ Laser T-Markings), Expo Arms 7075 Stripped AR-15 Upper Receiver, Geissele Automatics Super Duty Stripped Upper Receiver, Palmetto State Armory AR-15 Stripped Upper Receiver
Muzzle thread
- Muzzle devices
- Dead Air XRF Xeno Rimfire Muzzle Brake, HUXWRX Flash Hider-QD 556 1/2x28 (fit unchecked), Mil-spec A2 flash hider, 1/2-28 (drawing 9349051), Nordic Components 1/2-28 thread protector (ships on the 22RB), Otter Creek Labs Polonium, Otter Creek Labs Polonium K, Precision Armament M4-72 Severe-Duty® Compensator, SilencerCo Sparrow 22 (fit unchecked), SureFire ProComp 556 Muzzle Brake, SureFire SOCOM 3-Prong Flash Hider, SureFire SOCOM 4-Prong Flash Hider, SureFire WARCOMP Flash Hider, Taurus TX22 Thread Protector, VG6 Precision GAMMA 556
Gas block journal
- Gas blocks
- Aero Precision .750 low profile gas block, BCM Front Sight Base F - FSB (ID .750) - Milspec for Flat Top Uppers, BCM Low Profile Gas Block (steel with set screws) 750, SLR Rifleworks Sentry 7 Set Screw Adjustable Gas Block, Superlative Arms .750" Adjustable Gas Block, Bleed Off - Set Screw
Gas system length
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- BCM $279.00 Nov 21, 2026, out of stock that day
- Primary Arms $279.00 Nov 21, 2026, out of stock that day