Lower receiver
Aero Precision M4E1 Stripped Lower Receiver
Aero's enhanced forging, bare: "The M4E1 Lower Receiver delivers billet aesthetics in a forged package. This custom-designed enhanced forging is machined from 7075-T6 Aluminum and compatible with all mil-spec AR15 parts." Its trigger guard is part of the forging ("Integrated Trigger Guard"), its magazine well's mouth is flared, and it is "Marked and milled to accept short-throw safety selectors, but will work with standard selectors as well". It comes with two small pieces that aren't drawn: "Includes: Stripped M4E1 Lower Receiver / Nylon tipped tensioning set screw / Threaded Bolt Catch Pin" (the "Upper Tension Screw ... inserted in the grip tang", and the pin the bolt catch turns on). Marked "Cal Multi", serial numbers "M4-" (Aero's page).

- Weight
- 8.35 oz Conflictpublished: Aero Precision, the maker, read Oct 12, 2026Its sources span 8.34 oz to 8.62 oz.
- Lowest price
- $129.99 at AR15Discounts, read Nov 21, 2026 (OD Green Anodized)
- Maker's number
- APAR600001C
- Colours
- Anodized Black, FDE Cerakote, OD Green Anodized, OD Green Cerakote, Kodiak Brown Anodized, Sniper Grey Cerakote
- Drawn as
- modelled
- Maker's page
- aeroprecisionusa.com
In “Aero M4E1 Enhanced, pencil barrel”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Receiver maximum width (Z)1.374 in ± 0.03 in 34.9 mmProvisionalWorked out: {aero-m4e1-lower.width}
Worked out 1.374 in ± 0.03 in used
{aero-m4e1-lower.width}, harvested
The same receiver: Aero's complete lower's page lists what it is built on, "Includes: M4E1 Stripped Lower Receiver - Anodized Black / M4 Stock - Black / A2 Grip - Black / Mil-spec Lower Parts Kit / Carbine Receiver Extension / AR15 Carbine Buffer and Spring" (https://www.aeroprecisionusa.com/m4e1-complete-lower-a2-grip-m4-stock-black, read on the harvested copy 2026-10-12). Its widest, across the right panel's face and the left bosses' face at the deck, as read there on two specimens' bottom views (its own entry has three readings and their conflict). No page states a width. IN CONFLICT THERE, and so here: its readings are front 1.558, faces 1.374, front-own-scale 1.418; the one adopted there (faces) is the figure taken.
Receiver extension (bore) axis above the takedown pin centre0.877 in ± 0.0015 in 22.3 mmConfirmedWorked out: {std.ar15.bore_axis_y}
Worked out 0.8775 in ± 0.0015 in used
{std.ar15.bore_axis_y}, harvested
Aero, of the M4E1 lower: "This custom-designed enhanced forging is machined from 7075-T6 Aluminum and compatible with all mil-spec AR15 parts" (its page). The threaded hole's centre is the Army drawing's (.629 above the deck), as the complete lower's entry has it.
Magazine seat, X (a seated magazine's frame origin ahead of the takedown pin)3.491 in ± 0.03 in 88.7 mmProvisionalWorked out: {aero-m4e1-lower.magazine_seat_x}
Worked out 3.4915 in ± 0.03 in used
{aero-m4e1-lower.magazine_seat_x}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). A standard well inside (Aero: "Works with standard AR15 components and magazines"; its "Increased Magwell Flare" is the mouth): where a magazine seats in a mil-spec well, from the Army drawing's well and catch slot. No photo of a magazine seated in an M4E1 is on file.
Magazine seat, Y (the feed-lip top of a seated magazine)1.003 in ± 0.05 in 25.5 mmProvisionalWorked out: {aero-m4e1-lower.magazine_seat_y}
Worked out 1.003 in ± 0.05 in used
{aero-m4e1-lower.magazine_seat_y}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). As magazine_seat_x: the standard well's and the catch's, a check and not this receiver's outside.
Receiver underside behind the grip's lug (where a grip's flat top bears), Y, as the side outline reads it-1.063 in ± 0.02 in -27 mmProvisionalPhoto: right side, Aero's studio photo of the stripped M4E1, pin-framed by its open holes
Photo -1.063 in ± 0.02 in used
right side, Aero's studio photo of the stripped M4E1, pin-framed by its open holes, harvested
Scale: frame from the reviewed holes takedown (179.5,230.5) r=14px, pivot (937.5,228.5) r=8px (118.9 px/in, rms 0.000 in over 2 points). Read by y_min in x [-0.26, -0.15] of the traced outline (tools/trace.py)
The outline's level stretch just behind the grip's lug (and behind the set screw's end, which stands out of the lug's rear from X -0.13): this receiver's own reading of where a grip's flat top bears. The seat itself is the Army drawing's (grip_seat_y, -1.0695).
The outline's short level stretch between the rear underside's sweep and the lug: this receiver's own reading of the plane a grip's top bears on. The seat itself is the drawing's (grip_seat_y). Filled by the trace (tools/trace.py, the seed's `right` spec).
Grip seat, Y (the underside a grip's flat top bears on, at the takedown pin's X)-1.069 in ± 0.011 in -27.2 mmConfirmedWorked out: {std.ar15.deck_y} - {std.ar15.grip_seat_below_deck}
Worked out -1.0695 in ± 0.0115 in used
{std.ar15.deck_y} - {std.ar15.grip_seat_below_deck}, harvested
Aero, of the M4E1 lower: "This custom-designed enhanced forging is machined from 7075-T6 Aluminum and compatible with all mil-spec AR15 parts" (its page). The flat the lug hangs from is the drawing's, 1.318 ±.010 below the deck: a grip chosen in its own slot hangs from here. (NOT taken from the complete lower's entry of this name, which holds -1.443: the lowest point of the silhouette under the takedown pin, which is the lug's sloped face, 0.37 in below the seat. Nothing mates there on that part, whose grip is its own; said in this part's report.)
Worked out -1.063 in ± 0.02 in
{.grip_mating_y}, harvested
This receiver's own side photo, by the traced outline: the level stretch just behind the lug (grip_mating_y), 0.007 above the drawing's.
The drawing dimensions it, Aero says the forging takes mil-spec parts, and this receiver's outline reads the stretch behind the lug on it within a pixel.
Trigger guard front ear hole, X3.342 in ± 0.007 in 84.9 mmConfirmedWorked out: {std.ar15.trigger_guard_front_x}
Worked out 3.3425 in ± 0.007 in used
{std.ar15.trigger_guard_front_x}, harvested
Where a mil-spec lower's front ear hole is (the Army drawing's). THIS RECEIVER HAS NO EARS: its trigger guard is part of the forging (Aero: "Integrated Trigger Guard - Eliminates the possibility of breaking the trigger guard tabs by integrating the trigger guard into the lower"), so the slot is occupied and nothing pins here; the figure frames the anchor, as the category asks of a lower with an integral guard.
Trigger guard front ear hole, Y-2.18 in ± 0.01 in -55.4 mmConfirmedWorked out: {std.ar15.trigger_guard_rear_y}
Worked out -2.18 in ± 0.01 in used
{std.ar15.trigger_guard_rear_y}, harvested
As trigger_guard_front_x: the drawing's two guard holes are on one centre line, 2.18 below the takedown pin. No hole is there on this receiver.
Trigger guard rear ear hole, X1.498 in ± 0.01 in 38.1 mmConfirmedWorked out: {std.ar15.trigger_guard_rear_x}
Worked out 1.4985 in ± 0.01 in used
{std.ar15.trigger_guard_rear_x}, harvested
As trigger_guard_front_x: the drawing's place for the rear ear's roll pin. No hole is there on this receiver (its side photos show none).
Trigger guard rear ear hole, Y-2.18 in ± 0.01 in -55.4 mmConfirmedWorked out: {std.ar15.trigger_guard_rear_y}
Worked out -2.18 in ± 0.01 in used
{std.ar15.trigger_guard_rear_y}, harvested
As trigger_guard_rear_x.
Trigger pin hole centre, X1.928 in ± 0.004 in 49 mmConfirmedWorked out: {std.ar15.trigger_pin_x}
Worked out 1.928 in ± 0.004 in used
{std.ar15.trigger_pin_x}, harvested
Aero, of the M4E1 lower: "This custom-designed enhanced forging is machined from 7075-T6 Aluminum and compatible with all mil-spec AR15 parts" (its page). The trigger's hole is the Army drawing's: a trigger chosen in its own slot turns here, and the model's hole is cut here.
Trigger pin hole centre, Y-0.689 in ± 0.0035 in -17.5 mmConfirmedWorked out: {std.ar15.trigger_pin_y}
Worked out -0.689 in ± 0.0035 in used
{std.ar15.trigger_pin_y}, harvested
Aero, of the M4E1 lower: "This custom-designed enhanced forging is machined from 7075-T6 Aluminum and compatible with all mil-spec AR15 parts" (its page). The trigger's hole is the Army drawing's.
Worked out -0.677 in ± 0.015 in
{aero-m4e1-lower.trigger_pin_y}, harvested
By reference: the hole's centre as read on Aero's right side photo of the stripped M4E1 in its pin frame, recorded under the complete lower. 0.012 above the drawing's, inside its ±.
The drawing's: Aero says the forging takes mil-spec parts, the model's hole is cut there, and the photo's reading agrees within its ±.
The grip lug's rear face (under the takedown pin), X-0.075 in ± 0.025 in -1.9 mmConfirmedWorked out: {std.ar15.receiver_rear_x} + {std.ar15.grip_lug_front_from_rear_face} - {std.ar15.grip_lug_length}
Worked out -0.075 in ± 0.025 in used
{std.ar15.receiver_rear_x} + {std.ar15.grip_lug_front_from_rear_face} - {std.ar15.grip_lug_length}, harvested
A mil-spec lower's lug ends 2.300 ahead of the rear face and is 1.25 long. Aero, of the M4E1 lower: "This custom-designed enhanced forging is machined from 7075-T6 Aluminum and compatible with all mil-spec AR15 parts" (its page).
Photo -0.077 in ± 0.013 in
right side, Aero's studio photo of the stripped M4E1, APAR600001C's gallery, both pin holes open, harvested
Scale: rifle frame from the reviewed holes takedown, pivot = (0, 0), (6.375, 0): 118.9 px/in. Read by the traced outline's two points on the lug's upright rear face below the set screw's stub, (-0.079, -1.291) and (-0.075, -1.371) (tools/trace.py); ± is a pixel and a half
The lug's rear face where it shows: above it, from Y -1.08 to -1.24, the silhouette stands 0.04 to 0.05 further back, which is the end of the upper tension set screw in the lug's rear (Aero ships it in the receiver; its bottom photo has it at the lug's rear end), not the lug.
The drawing's, which a grip's slot is made to; the outline has the face 0.002 from it.
The grip lug's bottom flat (where its sloped face ends, behind the trigger guard's root), Y-2 in ± 0.021 in -50.8 mmConfirmedWorked out: {std.ar15.deck_y} - {std.ar15.grip_seat_below_deck} - {std.ar15.grip_lug_depth}
Worked out -1.9995 in ± 0.0215 in used
{std.ar15.deck_y} - {std.ar15.grip_seat_below_deck} - {std.ar15.grip_lug_depth}, harvested
A mil-spec lower: the flat is .93 below the seat.
Photo -1.983 in ± 0.013 in
right side, Aero's studio photo of the stripped M4E1, APAR600001C's gallery, both pin holes open, harvested
Scale: rifle frame from the reviewed holes takedown, pivot = (0, 0), (6.375, 0): 118.9 px/in. Read by the traced outline's two points on the flat at the sloped face's foot, (0.991, -1.987) and (1.143, -1.979): their mean (tools/trace.py); ± is a pixel and a half
The flat, 0.017 above the drawing's: inside the two ±.
The drawing's; the outline has the flat 0.017 above it, inside its ±.
The grip lug's sloped face, from the vertical60° ± 2°ConfirmedWorked out: {std.ar15.grip_lug_face_angle}
Worked out 60 deg ± 2 deg used
{std.ar15.grip_lug_face_angle}, harvested
A mil-spec lower: the lug is the drawing's (60° ±2°).
Photo 60 deg ± 1 deg
right side, Aero's studio photo of the stripped M4E1, APAR600001C's gallery, both pin holes open, harvested
Scale: rifle frame from the reviewed holes takedown, pivot = (0, 0), (6.375, 0): 118.9 px/in. Read by the traced outline's one straight stretch along the lug's sloped face, from (-0.075, -1.371) to (0.991, -1.987): its lean from the vertical over 1.23 in (tools/trace.py); ± is a pixel at each end
The sloped face: on the drawing's angle, and on its line within 0.004 in at both ends (1.228 from the pin).
The drawing's; the outline's stretch is on it.
The integral trigger guard's root, its rear face (where the grip's lug ends: a mil-spec lower's ears' rear face), X1.175 in ± 0.015 in 29.8 mmConfirmedWorked out: {std.ar15.receiver_rear_x} + {std.ar15.grip_lug_front_from_rear_face}
Worked out 1.175 in ± 0.015 in used
{std.ar15.receiver_rear_x} + {std.ar15.grip_lug_front_from_rear_face}, harvested
A mil-spec lower: the lug ends at the guard's ears, 2.300 ahead of the rear face: where a grip's nose comes to.
Photo 1.155 in ± 0.02 in
right side, Aero's studio photo of the stripped M4E1, APAR600001C's gallery, both pin holes open, harvested
Scale: rifle frame from the reviewed holes takedown, pivot = (0, 0), (6.375, 0): 118.9 px/in. Read by the traced outline's upright edge below the lug's flat, from (1.143, -1.979) to (1.167, -2.324): its middle (tools/trace.py); ± covers its lean and a pixel
The rear face of the block the integral guard's bar springs from: it leans 0.024 forward going down, and its middle is 0.02 behind the drawing's ears.
The drawing's, which a grip's nose is made to; the outline's edge is within its ± of it.
The rear underside (behind the grip's lug, under the tower), the radius of its arc on the centre plane0.75 in ± 0.01 in 19 mmProvisionalWorked out: {std.ar15.rear_underside_arc_r}
Worked out 0.75 in ± 0.01 in used
{std.ar15.rear_underside_arc_r}, harvested
The reference CAD model's arc on a mil-spec forging, about the model's centre (std.ar15.rear_underside_arc_center_x, _below_seat).
Photo 0.764 in ± 0.013 in
right side, Aero's studio photo of the stripped M4E1, APAR600001C's gallery, both pin holes open, harvested
Scale: rifle frame from the reviewed holes takedown, pivot = (0, 0), (6.375, 0): 118.9 px/in. Read by the traced outline's five points along the underside from X -1.116 to -0.285 (tools/trace.py), each one's distance from the reference model's centre (-1.0238, -1.2623): 0.766, 0.762, 0.763, 0.764, 0.766; their mean; ± is a pixel and a half
Aero's forging has the standard forging's sweep under the tower: 0.012 to 0.016 outside the reference model's arc all along, and so 0.05 clear of the fullest forging on file, which a grip's saddle is cut to (std.ar15.rear_underside_arc_r_fullest).
The reference model's; this receiver's own silhouette runs 0.014 outside it, inside the two ±. The model draws the outline's own line.
The check that a grip made for a mil-spec lower clears this forging's rear underside: in a square side view the silhouette's lower edge there is the centre plane's line.
The receiver's rear face (the buffer tower's, where an end plate bears), X-1.125 in ± 0.005 in -28.6 mmConfirmedWorked out: {std.ar15.receiver_rear_x}
Worked out -1.125 in ± 0.005 in used
{std.ar15.receiver_rear_x}, harvested
Aero, of the M4E1 lower: "This custom-designed enhanced forging is machined from 7075-T6 Aluminum and compatible with all mil-spec AR15 parts" (its page). The face an end plate bears on is the Army drawing's, 7.503 -.006 behind the pivot pin.
Worked out -1.14 in ± 0.013 in
{aero-m4e1-lower.rear_face_x}, harvested
By reference: the rear face below the ring as Aero's right side photo reads it in its pin frame (the left photo -1.118: the complete lower's entry). 0.015 behind the drawing's: the two ± touch. The ring's near rim, a quarter inch nearer the lens than the pins the photo is scaled by, reads further back still (rear_behind_pin).
The drawing's: the end plate, the castle nut and the receiver extension are placed by the standard, and the model's rear face is cut there so the plate bears on it. The photo's reading is 0.015 behind it.
The integral trigger guard across (its post behind the trigger and its bar under it), Z0.59 in ± 0.02 in 15 mmProvisionalPhoto: bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote, APAR600002C: the rear at the top
Photo 0.59 in ± 0.02 in used
bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote, APAR600002C: the rear at the top, harvested
Scale: the magazine well seen through from below in the same view: its box is 94 to 95 px across (rows 600 to 628) for the drawing's .898 at the deck, 105.2 px/in, and the receiver's silhouette, which is its body at the seat's level, 93 to 94 px for the drawing's .880, 106.8 px/in: so the lens is some 87 in from the deck and the scale at the bar's lower face, 2.6 in nearer, is 108.4 px/in (the grip lug's flat reads 39 px there: .375 less its edge breaks at 108). Read by the bar's lower face is the lighter flat between two creases, found as the two largest steps of the mean luminance across rows 352 to 386 (behind its first slot) and rows 455 to 470 (between its two slots): 64 px and 63 px, 0.586 in at 108.4 px/in. ± covers a pixel at each crease and the scale's 1.5%
The flat's width. Either side of it, out to the silhouette, the view has a darker band 13 to 14 px wide: taken as the body's underside seen past a narrower guard (the side photos' lip), not as chamfers on a bar of the body's width, which the side photos would show as a band most of the bar's height and don't.
Below the grip seat's level this receiver is narrower than its body from the grip's lug forward to the magazine well, as a mil-spec lower is at its trigger guard's ears (the reference CAD model's 0.659 there: std.ar15.trigger_guard_ears_width). In the side photos the body's lower edge stands over the guard as a lip along the seat's level, and the guard's face is one flat with a thin chamfer on its inner edge. One reading, from the one view from below on file: provisional.
The two slots through the integral guard's bar, across (Z)0.335 in ± 0.02 in 8.5 mmProvisionalPhoto: bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote, APAR600002C: the rear at the top
Photo 0.335 in ± 0.02 in used
bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote, APAR600002C: the rear at the top, harvested
Scale: the magazine well seen through from below in the same view: its box is 94 to 95 px across (rows 600 to 628) for the drawing's .898 at the deck, 105.2 px/in, and the receiver's silhouette, which is its body at the seat's level, 93 to 94 px for the drawing's .880, 106.8 px/in: so the lens is some 87 in from the deck and the scale at the bar's lower face, 2.6 in nearer, is 108.4 px/in (the grip lug's flat reads 39 px there: .375 less its edge breaks at 108). Read by each slot's two edges on the bar's lower face, across: the rear slot's dark rims at columns 479.5 and 515 either side of the white (rows 405 to 435), the front slot's steps at 477.5 and 514 (rows 485 to 500): 35.5 and 36.5 px; their mean at 108.4 px/in
The bar under the trigger has two oblong slots through it, round-ended, a shorter one behind a longer (Dirty Bird's photo from below and ahead shows both through; Aero's view from below has white through the rear one, where the trigger's slot is above it, and the receiver's underside through the front one). Read on the one view from below: provisional, each end good to about 0.04 in.
The guard bar's rear slot, its rear end, X1.655 in ± 0.04 in 42 mmProvisionalPhoto: bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote, APAR600002C: the rear at the top
Photo 1.655 in ± 0.04 in used
bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote, APAR600002C: the rear at the top, harvested
Scale: along the receiver, on the bar's own plane: the well's rear wall, where the white seen through the spine slot begins down the middle (row 587.5), is 3.472 ahead of the takedown pin by the Army drawing (magwell_front_inner_x less magwell_length), and a row is 1/107.3 in there (108.4 less the view's lean of about 8 degrees along the receiver). Checked at the other end: the bar's rear edge at the guard's root, 1.175 by the drawing, should then be at row 341, and the view has it between rows 338 and 346. Read by the step from the bar to the white down the middle, row 392.5; ± covers the scale along the receiver, the bar's own rise and fall under that lean (0.03) and a pixel
The guard bar's rear slot, its front end, X2.279 in ± 0.04 in 57.9 mmProvisionalPhoto: bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote, APAR600002C: the rear at the top
Photo 2.279 in ± 0.04 in used
bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote, APAR600002C: the rear at the top, harvested
Scale: along the receiver, on the bar's own plane: the well's rear wall, where the white seen through the spine slot begins down the middle (row 587.5), is 3.472 ahead of the takedown pin by the Army drawing (magwell_front_inner_x less magwell_length), and a row is 1/107.3 in there (108.4 less the view's lean of about 8 degrees along the receiver). Checked at the other end: the bar's rear edge at the guard's root, 1.175 by the drawing, should then be at row 341, and the view has it between rows 338 and 346. Read by the step back up to the bar's flat down the middle, row 459.5 (the white ends at row 447.5: beyond it the slot shows the receiver's underside, dark); ± covers the scale along the receiver, the bar's own rise and fall under that lean (0.03) and a pixel
The guard bar's front slot, its rear end, X2.433 in ± 0.04 in 61.8 mmProvisionalPhoto: bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote, APAR600002C: the rear at the top
Photo 2.433 in ± 0.04 in used
bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote, APAR600002C: the rear at the top, harvested
Scale: along the receiver, on the bar's own plane: the well's rear wall, where the white seen through the spine slot begins down the middle (row 587.5), is 3.472 ahead of the takedown pin by the Army drawing (magwell_front_inner_x less magwell_length), and a row is 1/107.3 in there (108.4 less the view's lean of about 8 degrees along the receiver). Checked at the other end: the bar's rear edge at the guard's root, 1.175 by the drawing, should then be at row 341, and the view has it between rows 338 and 346. Read by the step down from the bar's flat down the middle, row 476; ± covers the scale along the receiver, the bar's own rise and fall under that lean (0.03) and a pixel
The guard bar's front slot, its front end, X3.258 in ± 0.04 in 82.8 mmProvisionalPhoto: bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote, APAR600002C: the rear at the top
Photo 3.258 in ± 0.04 in used
bottom view, Aero's studio photo of the stripped M4E1 in FDE Cerakote, APAR600002C: the rear at the top, harvested
Scale: along the receiver, on the bar's own plane: the well's rear wall, where the white seen through the spine slot begins down the middle (row 587.5), is 3.472 ahead of the takedown pin by the Army drawing (magwell_front_inner_x less magwell_length), and a row is 1/107.3 in there (108.4 less the view's lean of about 8 degrees along the receiver). Checked at the other end: the bar's rear edge at the guard's root, 1.175 by the drawing, should then be at row 341, and the view has it between rows 338 and 346. Read by where the slot's lit front wall ends at the bar's flat down the middle, row 564.5; ± covers the scale along the receiver, the bar's own rise and fall under that lean (0.03) and a pixel
The raised block round the magazine catch on the right side (the 'panel'), where its face ends at the front, X3.64 in ± 0.02 in 92.5 mmCorroboratedPhoto: right side, Aero's studio photo of the stripped M4E1, APAR600001C's gallery, both pin holes open
Photo 3.64 in ± 0.02 in used
right side, Aero's studio photo of the stripped M4E1, APAR600001C's gallery, both pin holes open, harvested
Scale: rifle frame from the reviewed holes takedown (179.5, 230.5), pivot (937.5, 228.5) = (0, 0), (6.375, 0): 118.9 px/in. Read by the mean luminance along the row 0.15 in below the pin line (above the catch's pocket), a working script the block's face is one tone (54 to 59) from X 3.03 to 3.62, then a lit band (67 to 78) from 3.64 to 3.80, then the face's tone again (53 to 58) from 3.83 on. The face ends where the band begins; the band's largest step is at 3.66. Along the row 0.97 below the pin line the block's lit lower chamfer ends at 3.65. ± is two pixels
Photo 3.69 in ± 0.04 in
right side, Sportsman's Warehouse's photo of the stripped M4E1, 1200 px, both pin holes open, harvested
Scale: rifle frame from the two pin holes' see-through (their bright centroids: (204.4, 496.9) and (1127.5, 495.2)) = (0, 0), (6.375, 0): 144.8 px/in; the see-through is not the rim, so ± is wider. Read by the same row in the larger picture: the face's tone to 3.66, the lit band from 3.69 to 3.87 (its largest step at 3.71), the face's tone from 3.91 on
The photo whose frame is the reviewed rims of the pin holes; the larger picture, framed by its holes' see-through, reads the same edge 0.05 ahead, inside the two ±.
On the right side the forging stands out round the magazine catch's button as a block with chamfered edges, and ahead of it the magazine well's wall (the face the large A is cut in) is lower: in both right side photos the block's flat face ends in a lit chamfer and the same grey as the face comes back ahead of it. Its face is panel_right_out (0.664 from the centre, read from below under the complete lower); the wall ahead of it is wall_right_below_panel (0.56, read on the front view below the block, where nothing hides it), a hundredth outside a mil-spec well's wall. The complete lower's receiver is drawn with the block's face carried on to the pivot lug: said in this part's report.
The catch block's front chamfer, its length along X (from the face's end down to the well's wall)0.16 in ± 0.04 in 4.1 mmCorroboratedPhoto: right side, Aero's studio photo of the stripped M4E1, APAR600001C's gallery, both pin holes open
Photo 0.16 in ± 0.04 in used
right side, Aero's studio photo of the stripped M4E1, APAR600001C's gallery, both pin holes open, harvested
Scale: rifle frame from the reviewed holes takedown (179.5, 230.5), pivot (937.5, 228.5) = (0, 0), (6.375, 0): 118.9 px/in. Read by the lit band's length along the same row, from 3.64 to 3.80; ± is two pixels at each end
With the block 0.104 proud of the wall (panel_right_out less wall_right_below_panel) a chamfer this long leans 33 degrees: as long as the block's rear ramp (panel_right_ramp, 0.17).
Photo 0.18 in ± 0.04 in
right side, Sportsman's Warehouse's photo of the stripped M4E1, 1200 px, both pin holes open, harvested
Scale: rifle frame from the two pin holes' see-through (their bright centroids: (204.4, 496.9) and (1127.5, 495.2)) = (0, 0), (6.375, 0): 144.8 px/in; the see-through is not the rim, so ± is wider. Read by the lit band's length along the same row in the larger picture, from 3.69 to 3.87
As catch_block_front_x; the two agree within a pixel.
Overall height: the tower ring's top to the lowest point (the end views are scaled by it)4.079 in ± 0.03 in 103.6 mmProvisionalWorked out: {aero-m4e1-lower.height}
Worked out 4.079 in ± 0.03 in used
{aero-m4e1-lower.height}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). What this part's end views are scaled by.
The buffer tower's ring, across (the end view; the standard's is 1.392)1.351 in ± 0.03 in 34.3 mmProvisionalWorked out: {aero-m4e1-lower.tower_od}
Worked out 1.351 in ± 0.03 in used
{aero-m4e1-lower.tower_od}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). The ring across, on Aero's rear view (the standard's round ring is 1.392: Aero's has flats on its sides); the bottom view is scaled by it. IN CONFLICT THERE, and so here: its readings are rear 1.351, rear_fde 1.275; the one adopted there (rear) is the figure taken.
Rear of the buffer-tower ring behind the takedown pin1.155 in ± 0.013 in 29.3 mmCorroboratedWorked out: {aero-m4e1-lower.rear_behind_pin}
Worked out 1.155 in ± 0.013 in used
{aero-m4e1-lower.rear_behind_pin}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). The outline's rearmost point: the ring's near rim. The rear face itself is rear_end_x.
Front of the pivot-pin lug ahead of the takedown pin6.547 in ± 0.022 in 166.3 mmProvisionalWorked out: {aero-m4e1-lower.front_ahead_of_pin}
Worked out 6.547 in ± 0.022 in used
{aero-m4e1-lower.front_ahead_of_pin}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). IN CONFLICT THERE, and so here: its readings are right 6.547, left 6.645; the one adopted there (right) is the figure taken.
Top of the buffer-tower ring above the pin line1.554 in ± 0.013 in 39.5 mmCorroboratedWorked out: {aero-m4e1-lower.tower_top_above_pin}
Worked out 1.554 in ± 0.013 in used
{aero-m4e1-lower.tower_top_above_pin}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). The end views' offset.
Receiver top deck above the pin line0.247 in ± 0.013 in 6.3 mmCorroboratedWorked out: {aero-m4e1-lower.deck_above_pin}
Worked out 0.247 in ± 0.013 in used
{aero-m4e1-lower.deck_above_pin}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). The outline's own top edge. The model's deck is the Army drawing's plane (std.ar15.deck_y, .2485), which this is a reading of.
Lowest point below the pin line (the integral guard or the magwell front)2.508 in ± 0.014 in 63.7 mmCorroboratedWorked out: {aero-m4e1-lower.bottom_below_pin}
Worked out 2.508 in ± 0.014 in used
{aero-m4e1-lower.bottom_below_pin}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). The integral trigger guard's bow.
Magwell front face, X6.156 in ± 0.021 in 156.4 mmProvisionalWorked out: {aero-m4e1-lower.magwell_front_x}
Worked out 6.156 in ± 0.021 in used
{aero-m4e1-lower.magwell_front_x}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). IN CONFLICT THERE, and so here: its readings are right 6.156, left 6.268; the one adopted there (right) is the figure taken.
Receiver rear face below the tower ring, X-1.14 in ± 0.013 in -29 mmCorroboratedWorked out: {aero-m4e1-lower.rear_face_x}
Worked out -1.14 in ± 0.013 in used
{aero-m4e1-lower.rear_face_x}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). The bottom view's offset.
The receiver's rear below the tower ring, across (Z)1.04 in ± 0.03 in 26.4 mmProvisionalWorked out: {aero-m4e1-lower.rear_body_width}
Worked out 1.04 in ± 0.03 in used
{aero-m4e1-lower.rear_body_width}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method). The rear view's outline at those heights (the bosses and the right panel, 3 to 4.5 in ahead): not the rear end's own width.
The right side panel's face, from the centre plane0.664 in ± 0.02 in 16.9 mmCorroboratedWorked out: {aero-m4e1-lower.panel_right_out}
Worked out 0.664 in ± 0.02 in used
{aero-m4e1-lower.panel_right_out}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
The right side panel's face, where it begins (its ramp's foot 0.17 behind)3.09 in ± 0.04 in 78.5 mmProvisionalWorked out: {aero-m4e1-lower.panel_right_rear_x}
Worked out 3.09 in ± 0.04 in used
{aero-m4e1-lower.panel_right_rear_x}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
The right side panel's ramp up from the body, its length along x0.17 in ± 0.04 in 4.3 mmProvisionalWorked out: {aero-m4e1-lower.panel_right_ramp}
Worked out 0.17 in ± 0.04 in used
{aero-m4e1-lower.panel_right_ramp}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
The right side panel's lower edge, Y (below it the well's wall steps in)-1.03 in ± 0.04 in -26.2 mmProvisionalWorked out: {aero-m4e1-lower.panel_right_bottom_y}
Worked out -1.03 in ± 0.04 in used
{aero-m4e1-lower.panel_right_bottom_y}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
The well's right wall below the panel, from the centre plane0.56 in ± 0.03 in 14.2 mmProvisionalWorked out: {aero-m4e1-lower.wall_right_below_panel}
Worked out 0.56 in ± 0.03 in used
{aero-m4e1-lower.wall_right_below_panel}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
The left side's face over the magazine well, from the centre plane0.603 in ± 0.03 in 15.3 mmProvisionalWorked out: {aero-m4e1-lower.panel_left_out}
Worked out 0.603 in ± 0.03 in used
{aero-m4e1-lower.panel_left_out}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
The left side's face over the well, where it begins (its ramp's foot 0.08 behind)3.03 in ± 0.04 in 77 mmProvisionalWorked out: {aero-m4e1-lower.panel_left_rear_x}
Worked out 3.03 in ± 0.04 in used
{aero-m4e1-lower.panel_left_rear_x}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
The left face's ramp up from the body, its length along x0.08 in ± 0.03 in 2 mmProvisionalWorked out: {aero-m4e1-lower.panel_left_ramp}
Worked out 0.08 in ± 0.03 in used
{aero-m4e1-lower.panel_left_ramp}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
The pad round the magazine catch's slot (left), its face from the centre plane0.666 in ± 0.02 in 16.9 mmCorroboratedWorked out: {aero-m4e1-lower.catch_pad_out}
Worked out 0.666 in ± 0.02 in used
{aero-m4e1-lower.catch_pad_out}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
The catch pad's upper edge, Y-0.3 in ± 0.04 in -7.6 mmProvisionalWorked out: {aero-m4e1-lower.catch_pad_top_y}
Worked out -0.3 in ± 0.04 in used
{aero-m4e1-lower.catch_pad_top_y}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
The catch pad's lower edge, Y-0.78 in ± 0.05 in -19.8 mmProvisionalWorked out: {aero-m4e1-lower.catch_pad_bottom_y}
Worked out -0.78 in ± 0.05 in used
{aero-m4e1-lower.catch_pad_bottom_y}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
The catch pad's rounded front end, X4.56 in ± 0.03 in 115.8 mmProvisionalWorked out: {aero-m4e1-lower.catch_pad_front_x}
Worked out 4.56 in ± 0.03 in used
{aero-m4e1-lower.catch_pad_front_x}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
The catch pad's rear end, X3.048 in ± 0.012 in 77.4 mmConfirmedWorked out: {aero-m4e1-lower.catch_pad_rear_x}
Worked out 3.048 in ± 0.012 in used
{aero-m4e1-lower.catch_pad_rear_x}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
Aero's bolt catch bosses, their face from the centre plane (left)0.708 in ± 0.02 in 18 mmCorroboratedWorked out: {aero-m4e1-lower.bolt_catch_boss_out}
Worked out 0.708 in ± 0.02 in used
{aero-m4e1-lower.bolt_catch_boss_out}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
Aero's rear bolt catch boss, its rear end, X3.01 in ± 0.05 in 76.5 mmProvisionalWorked out: {aero-m4e1-lower.bolt_catch_boss_rear_x}
Worked out 3.01 in ± 0.05 in used
{aero-m4e1-lower.bolt_catch_boss_rear_x}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
Aero's front bolt catch boss, its front end, X3.52 in ± 0.05 in 89.4 mmProvisionalWorked out: {aero-m4e1-lower.bolt_catch_boss_front_x}
Worked out 3.52 in ± 0.05 in used
{aero-m4e1-lower.bolt_catch_boss_front_x}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
Aero's bolt catch bosses, their lower ends, Y (they rise to the deck)-0.02 in ± 0.04 in -0.5 mmProvisionalWorked out: {aero-m4e1-lower.bolt_catch_boss_bottom_y}
Worked out -0.02 in ± 0.04 in used
{aero-m4e1-lower.bolt_catch_boss_bottom_y}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
The front lug's slot as the front view's height scale reads it0.549 in ± 0.01 in 13.9 mmProvisionalWorked out: {aero-m4e1-lower.front_view_lug_slot}
Worked out 0.549 in ± 0.01 in used
{aero-m4e1-lower.front_view_lug_slot}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
The pivot lug's right ear, its outer face from the centre plane (the slot's middle)0.519 in ± 0.012 in 13.2 mmCorroboratedWorked out: {aero-m4e1-lower.ear_right_out}
Worked out 0.519 in ± 0.012 in used
{aero-m4e1-lower.ear_right_out}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
The pivot lug's left ear, its outer face from the centre plane (the slot's middle)0.542 in ± 0.012 in 13.8 mmCorroboratedWorked out: {aero-m4e1-lower.ear_left_out}
Worked out 0.542 in ± 0.012 in used
{aero-m4e1-lower.ear_left_out}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
The pivot lug across its two ears1.061 in ± 0.017 in 26.9 mmCorroboratedWorked out: {aero-m4e1-lower.ears_width}
Worked out 1.061 in ± 0.017 in used
{aero-m4e1-lower.ears_width}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
The right ear's outer face, where it begins: the right panel's front end, X6.18 in ± 0.015 in 157 mmProvisionalWorked out: {aero-m4e1-lower.ear_right_rear_x}
Worked out 6.18 in ± 0.015 in used
{aero-m4e1-lower.ear_right_rear_x}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
The left ear's outer face, where it begins: the foot of the ramp up to the left side's face, X (at the pin's height)6.15 in ± 0.02 in 156.2 mmProvisionalWorked out: {aero-m4e1-lower.ear_left_rear_x}
Worked out 6.15 in ± 0.02 in used
{aero-m4e1-lower.ear_left_rear_x}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
The ramp from the left ear's face up to the left side's face, its length along X0.06 in ± 0.03 in 1.5 mmProvisionalWorked out: {aero-m4e1-lower.ear_left_ramp}
Worked out 0.06 in ± 0.03 in used
{aero-m4e1-lower.ear_left_ramp}, harvested
By reference: the same receiver, read on Aero's photos of the stripped M4E1 and recorded under the complete lower (its entry has the photo, the scale and the method).
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
AR-15 receiver pins
- Uppers
- Aero Precision M4E1 Enhanced Upper Receiver Stripped, Aero Precision M4E1 Threaded upper receiver, BCM M4 Upper Receiver Assembly (w/ Laser T-Markings), Expo Arms 7075 Stripped AR-15 Upper Receiver, Geissele Automatics Super Duty Stripped Upper Receiver, Nordic Components 22RB .22 LR upper, 16", Palmetto State Armory AR-15 Stripped Upper Receiver, Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12", Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16"
AR-15 receiver extension thread
- Folding stock adapters
- Law Tactical AR Folding Stock Adapter Gen 3-M, Law Tactical AR Folding Stock Adapter GEN-S, Sylvan Arms SA5 Pro AR15 Folding Stock Adapter (Opens To The Left), Sylvan Arms SA5 Pro AR15 Folding Stock Adapter (Opens To The Right)
- Receiver extensions
- BCM Milspec Carbine Receiver Extension (Buffer Tube) 6 Position, BCM MK2 Receiver Extension, Geissele Automatics Premium Mil-Spec Buffer Tube, Guntec USA AR-15 Mil-Spec Buffer Tube (Gen 2), SB Tactical SBPDW receiver extension, housing and integral castle nut, VLTOR RE-A5 7-Position Receiver Extension, MilSpec Diameter
AR-15 magazine well
AR-15 grip mount
AR-15 trigger guard ears
- Trigger guards
- Magpul MOE enhanced trigger guard, polymer
AR-15 fire-control group (mounting only)
AR-15 lower parts kit
- Lower parts kits
- CMMG Lower Parts Kit, AR15, Rise Armament Lower parts kit, less trigger
AR-15 safety selector
- Safety selectors
- CMMG Safety Selector, AR15, Radian Weapons Talon 45/90 - 2 Lever Kit
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- AR15Discounts $129.99 OD Green Anodized Nov 21, 2026, stock not said
- AR15Discounts $129.99 Kodiak Brown Anodized Nov 21, 2026, stock not said
- AR15Discounts $139.99 Anodized Black Nov 21, 2026, stock not said
- AR15Discounts $149.99 FDE Cerakote Nov 21, 2026, stock not said
- Aero Precision $155.00 Anodized Black Nov 21, 2026, stock not said
- Aero Precision $155.00 OD Green Anodized Nov 21, 2026, stock not said
- Aero Precision $155.00 Kodiak Brown Anodized Nov 21, 2026, stock not said
- Aero Precision $175.00 FDE Cerakote Nov 21, 2026, stock not said
- Aero Precision $175.00 OD Green Cerakote Nov 21, 2026, stock not said
- Aero Precision $175.00 Sniper Grey Cerakote Nov 21, 2026, stock not said
- GRITR Sports $112.99 Anodized Black Nov 21, 2026, out of stock that day
- Midwest Gun Works $139.99 Anodized Black Nov 21, 2026, out of stock that day
- Sportsman's Warehouse $139.99 Anodized Black Nov 21, 2026, out of stock that day
- Dirty Bird Industries $139.99 Anodized Black Nov 21, 2026, out of stock that day
- Dirty Bird Industries $139.99 OD Green Anodized Nov 21, 2026, out of stock that day
- Dirty Bird Industries $139.99 Kodiak Brown Anodized Nov 21, 2026, out of stock that day
- Aerospace Arms $139.99 Anodized Black Nov 21, 2026, out of stock that day
- Alquist Arms $139.99 Anodized Black Nov 21, 2026, out of stock that day
- Right To Bear $154.99 Anodized Black Nov 21, 2026, out of stock that day
- Dirty Bird Industries $159.99 FDE Cerakote Nov 21, 2026, out of stock that day
- Rifle Supply $164.99 Anodized Black Nov 21, 2026, out of stock that day