Magazine
Magpul PMAG 20 AR/M4 GEN M3
Magpul's 20-round polymer magazine for AR-15/M4 rifles in 5.56 NATO and .223 Remington, the third generation: the 30-round's top on a body an inch and nine tenths shorter, which Magpul's sheet says 'accomodates firing from a prone position'. Its sheet says a pop-off impact and dust cover is included; it comes off before the magazine goes into a rifle and is not drawn.

- Weight
- 4 oz ± 0.5 oz Confirmedpublished: Magpul, PMAG 20 AR/M4 GEN M3 (MAG560), Technical Specifications, the maker, read Oct 13, 2026
- Lowest price
- $11.99 at KYGUNCO, read Nov 21, 2026 (Black)
- Made for
- a 20-round polymer magazine for AR15/M4 compatible weapons chambered in 5.56x45 NATO / .223 Remington
- Maker's number
- MAG560
- Colours
- Black, ODG
- Drawn as
- modelled
- Maker's page
- magpul.com
In “Aero 16 in, slick rail and a 1-6x”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Overall height, feed lips to base5.6 in ± 0.1 in 142.2 mmConfirmedPublished: Magpul, PMAG 20 AR/M4 GEN M3 (MAG560), Technical Specifications, the maker, read Oct 13, 2026
Published “Length, max 5.6 in.” used
Magpul, PMAG 20 AR/M4 GEN M3 (MAG560), Technical Specifications, the maker, read Oct 13, 2026 the page, harvested Oct 13, 2026
Magpul's 'Length, max', taken as the height from the top of the feed lips to the lowest point of the floorplate with the top section upright, as a magazine well holds it (the patent's side elevation is drawn so). What says it spans that: scaled by it, the patent's side elevation has this magazine's top section, spine to front face, as long as the 30-round GEN M3's (front_to_back: the two readings and their difference are there), and both go into the one standard well. Measured instead along the lean of its lower half it would be a little more; the ± covers that.
Body height below the feed-lip blockNo value yetMissingNo source yet
Onboarding checklist: Side view; overall_height minus the feed-lip block when the block is shared across a product line. Not read: the block is not a piece of its own on a PMAG (the body is one moulding to the lips).
Feed-lip block heightNo value yetMissingNo source yet
Onboarding checklist. Not read: a PMAG's body is one moulding from the floorplate to the feed lips, with no block to split off.
Front to back at the body top2.496 in ± 0.045 in 63.4 mmCorroboratedPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi
Worked out 2.528 in ± 0.035 in
{magpul-pmag-30-gen-m3.front_to_back}
Magpul's 30-round GEN M3's, by reference: the two are one generation for one magazine well (Magpul's sheets say of each 'Modified dimensions allow for wider compatibility with non Colt-spec platforms' in the same words, and its patent marking page lists the same utility patents against both: 8,069,601; 8,635,796; 8,991,086; 8,839,543; 7,908,780; 8,166,692; 7,958,660). Used to try what Magpul's 'Length, max' spans: this part's own patent's side elevation, scaled by 5.6 in as its upright height, has to give this.
Photo 2.496 in ± 0.045 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: scale from magpul-pmag-20-gen-m3.overall_height = 5.6 in (y-extent 2028 px → 362.1 px/in). Read by median row width in y [-2.6, -0.7] (2.496–2.496) of the traced outline (tools/trace.py); the top section's front to back where it is straight and stands in the well, spine's rear face to front face (the median row)
Photo 2.49 in ± 0.05 in
Magpul's own photo of MAG560's left side, gallery 02.1, black, on white, 1200 px, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the silhouette's 1032 px with the top section's edges stood upright (turned 0.2 degrees; its rear edge leans 0.3 and its front -0.7 in the photo): 184.2 px/in; x from the spine's rear face in the well (the photo mirrored), y from the feed lips' top (tools/trace.py, the `left-photo` spec). Read by the silhouette's width on rows through the top section: 2.47 at y -1.0, 2.49 at -2.0, 2.50 at -2.6; its outline lies on the patent's left elevation, IoU 0.987
This part's own design patent's elevation scaled by its own published height; Magpul's photograph of the product scaled the same way reads the same (2.49), and the 30-round's, by reference, 0.03 more: inside its ±. It goes into a standard well (2.553 in with the spine's slot) with 0.06 in to spare.
The top section that stands in the well, from the spine's rear face to the front face.
Magazine catch notch (left side), its upper edge below the feed lips' top1.055 in ± 0.03 in 26.8 mmCorroboratedPhoto: Magpul's own photo of MAG560's left side, gallery 02.1, black, on white, 1200 px
Photo 1.055 in ± 0.03 in used
Magpul's own photo of MAG560's left side, gallery 02.1, black, on white, 1200 px, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the silhouette's 1032 px with the top section's edges stood upright (turned 0.2 degrees; its rear edge leans 0.3 and its front -0.7 in the photo): 184.2 px/in; x from the spine's rear face in the well (the photo mirrored), y from the feed lips' top (tools/trace.py, the `left-photo` spec). Read by the catch's window is the rounded pocket at columns 701 to 791.5; its upper edge at row 291, which the placement puts 1.054 to 1.056 in under the lips' top; the ± is that pick, the silhouette's top and the height's own ± on an inch
Photo 1.107 in ± 0.03 in
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2071 px: 369.8 px/in; x from the spine's rear face in the well (the figure mirrored), y from the feed lips' top (tools/trace.py, the `left` spec). Read by the rounded rectangle's upper line, the middle of its stroke at row 1110
This magazine's own design patent (the one its maker's marking page lists against it): a drawing, 0.05 in lower than the photograph.
Worked out 1.07 in ± 0.04 in
{magpul-pmag-30-gen-m3.catch_notch_top}
The 30-round GEN M3's own reading (its photograph), by reference: both hang on the one catch in the one well, under one generation's feed lips.
Magpul's photograph of the product itself; the 30-round's own reading is 0.015 in from it and the patent's drawing within the two readings' ±.
What seats it: the notch's upper edge hangs on the lower's catch (the `magwell` anchor). Read on this magazine's own photograph; its own design patent draws the window 0.05 in lower, as the 30-round's patent does against that magazine's photograph (1.12 for 1.07): the photograph of the product decides, and the 30-round's own reading, by reference, is 0.015 from this one. All are scaled by Magpul's 'Length, max' as the upright height.
Magazine catch notch (left side), its height0.244 in ± 0.02 in 6.2 mmCorroboratedPhoto: Magpul's own photo of MAG560's left side, gallery 02.1, black, on white, 1200 px
Photo 0.244 in ± 0.02 in used
Magpul's own photo of MAG560's left side, gallery 02.1, black, on white, 1200 px, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the silhouette's 1032 px with the top section's edges stood upright (turned 0.2 degrees; its rear edge leans 0.3 and its front -0.7 in the photo): 184.2 px/in; x from the spine's rear face in the well (the photo mirrored), y from the feed lips' top (tools/trace.py, the `left-photo` spec). Read by the pocket's upper and lower edges, rows 291 and 336 (the dark lines of the two edges, +/- 1.5 px each): y -1.055 to -1.299
Photo 0.252 in ± 0.012 in
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2071 px: 369.8 px/in; x from the spine's rear face in the well (the figure mirrored), y from the feed lips' top (tools/trace.py, the `left` spec). Read by the rounded rectangle's upper and lower lines, the middles of their strokes at rows 1110 and 1203: y -1.107 to -1.359
Magpul's photograph of the product itself; the patent's drawing agrees within the two readings' ±, and is the lower's slot to the thousandth.
The window the catch comes into: as tall as the slot it comes through in a lower (std.ar15.mag_catch_slot_h, 0.252 in).
Magazine catch notch (left side), its rear end ahead of the spine's rear face0.483 in ± 0.03 in 12.3 mmCorroboratedPhoto: Magpul's own photo of MAG560's left side, gallery 02.1, black, on white, 1200 px
Photo 0.483 in ± 0.03 in used
Magpul's own photo of MAG560's left side, gallery 02.1, black, on white, 1200 px, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the silhouette's 1032 px with the top section's edges stood upright (turned 0.2 degrees; its rear edge leans 0.3 and its front -0.7 in the photo): 184.2 px/in; x from the spine's rear face in the well (the photo mirrored), y from the feed lips' top (tools/trace.py, the `left-photo` spec). Read by the pocket's rear edge, column 791.5 (+/- 1.5 px); the ± is that, the spine's edge in the photo and the scale
Photo 0.491 in ± 0.015 in
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2071 px: 369.8 px/in; x from the spine's rear face in the well (the figure mirrored), y from the feed lips' top (tools/trace.py, the `left` spec). Read by the rounded rectangle's rear line, the middle of its stroke at column 1672
Magpul's photograph of the product itself; the patent's drawing agrees within the two readings' ±.
Magazine catch notch (left side), its front end ahead of the spine's rear face0.974 in ± 0.03 in 24.7 mmCorroboratedPhoto: Magpul's own photo of MAG560's left side, gallery 02.1, black, on white, 1200 px
Photo 0.974 in ± 0.03 in used
Magpul's own photo of MAG560's left side, gallery 02.1, black, on white, 1200 px, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the silhouette's 1032 px with the top section's edges stood upright (turned 0.2 degrees; its rear edge leans 0.3 and its front -0.7 in the photo): 184.2 px/in; x from the spine's rear face in the well (the photo mirrored), y from the feed lips' top (tools/trace.py, the `left-photo` spec). Read by the pocket's front edge, column 701 (+/- 1.5 px): the window 0.49 in long
Photo 1.013 in ± 0.015 in
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2071 px: 369.8 px/in; x from the spine's rear face in the well (the figure mirrored), y from the feed lips' top (tools/trace.py, the `left` spec). Read by the rounded rectangle's front line, the middle of its stroke at column 1479: the rectangle 0.52 in long
Magpul's photograph of the product itself; the patent's drawing reads 0.04 in further forward, as the 30-round's does against its photograph.
The block under the catch notch (left side), standing out of the side0.057 in ± 0.006 in 1.4 mmCorroboratedPhoto: US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi
Photo 0.057 in ± 0.006 in used
US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in. Read by rows 1172 to 1212: the block's outer line at column 1017.5, the side's at 996.5: 21 px; its top between rows 1164 and 1172 (1.37 in under the lips' top), its chamfer back to the side by row 1244; ± 2 px
Photo 0.054 in ± 0.006 in
US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in. Read by rows 1172 to 1212: the block's outer line at column 1517.5, the side's at 1537.5: 20 px; ± 2 px
The two elevations agree within a pixel; the front one is the figure the front outline is traced from.
As on the 30-round GEN M3 (its ledger's catch_block_proud has the whole account): this magazine's own patent draws a block under the catch's window, in profile on the right of its front elevation and the left of its rear one, in outline on the left elevation; Magpul's photo of the product has its outline under the window with a darker band along its lower end. NOT RECONCILED WITH THE WELL, here either: hung by its notch, the block is under the catch's slot in a lower's left wall, where a standard well is .898 wide (std.ar15.magwell_width), and a top section 0.902 wide as drawn with this block on it is 0.96. It is not built.
The relief over the catch notch (left side), standing out of the side0.013 in ± 0.006 in 0.3 mmProvisionalPhoto: US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi
Photo 0.013 in ± 0.006 in used
US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in. Read by the traced outline's corner at 0.460 from the middle, 0.915 in under the lips, against the straight line through that side at 0.53 and 2.46 in under them (0.447 there); the other side has no such corner; ± 2 px
Over the catch's window this magazine's patent draws a four-sided outline as long as the block under it, from 0.75 to 1.11 in under the lips (its left elevation), and the front elevation's silhouette swells there on that side alone: a shallow boss or ramp over the window. Magpul's photo has its outline faintly. Not built (a thing at one place along the magazine, which a hull would carry down the whole left side into a well's wall); kept as read.
The block under the catch notch, its length along the magazine (front to back)0.38 in ± 0.03 in 9.7 mmCorroboratedPhoto: Magpul's own photo of MAG560's left side, gallery 02.1, black, on white, 1200 px
Photo 0.38 in ± 0.03 in used
Magpul's own photo of MAG560's left side, gallery 02.1, black, on white, 1200 px, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the silhouette's 1032 px with the top section's edges stood upright (turned 0.2 degrees; its rear edge leans 0.3 and its front -0.7 in the photo): 184.2 px/in; x from the spine's rear face in the well (the photo mirrored), y from the feed lips' top (tools/trace.py, the `left-photo` spec). Read by the dark lines of its two ends, columns 711 and 781 (+/- 1.5 px): x 0.539 to 0.919
Photo 0.4 in ± 0.015 in
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2071 px: 369.8 px/in; x from the spine's rear face in the well (the figure mirrored), y from the feed lips' top (tools/trace.py, the `left` spec). Read by the lower rectangle's two side lines, columns 1502 and 1650: x 0.55 to 0.95
Magpul's photograph of the product itself; the patent's drawing agrees within the two readings' ±.
The block under the catch notch, from the notch's lower edge down to where it is back in the side0.195 in ± 0.012 in 5 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi
Photo 0.195 in ± 0.012 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2071 px: 369.8 px/in; x from the spine's rear face in the well (the figure mirrored), y from the feed lips' top (tools/trace.py, the `left` spec). Read by the lower rectangle, from the rounded rectangle's lower line (row 1203) to its own lower line (row 1275): 72 px
The side panels' floors below the grip frame's ribs and bands0.027 in ± 0.006 in 0.7 mmCorroboratedPhoto: US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi
Photo 0.023 in ± 0.006 in
US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in. Read by rows 1820 to 2060 (the frame's one row of panels): the frame's silhouette at columns 656.5 and 1007.5, the panels' floor line at 664.5 and 998.5: 8.0 and 9.0 px, centre to centre; ± 2 px for two lines 3 px thick
Photo 0.027 in ± 0.006 in used
US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in. Read by rows 1860 to 2140: the frame's silhouette at columns 1528 and 1877.5, the panels' floor line at 1538 and 1867.5: 10 px each side; ± 2 px
The two readings are one thing within their ± (0.004 in apart, as on the 30-round: 0.025 and 0.029). The model's floors are the plain sides' own plane carried down and its frame the traced front outline's, whose two levels come out 0.028 in apart on the left and 0.030 on the right (the outline rides the strokes a line's weight outside their middles): the rear elevation's figure is the one that says what is built, within its ±.
How far the frame stands out of each side, read where this magazine's own patent shows a floor in profile, as the 30-round's does: the front column's panel runs out to the front face and the rear one to the spine, so the front and rear elevations have their floors as a line inside the frame's silhouette, and that line runs on from the silhouette of the plain sides above the frame (FIG. 6: 665.5 and 998 above, 664.5 and 998.5 between the bands). The one closed panel and the one with the dot matrix show in no profile and are taken to the same floor. Under the band, at the dot matrix's height, the silhouette is the rib between the two lower panels and stands 0.013 to 0.018 in over that floor, less than the bands.
A side panel's wall, from its rim on the frame in to its floor's edge, as the side view has it0.027 in ± 0.006 in 0.7 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi
Photo 0.027 in ± 0.006 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2071 px: 369.8 px/in; x from the spine's rear face in the well (the figure mirrored), y from the feed lips' top (tools/trace.py, the `left` spec). Read by the two lines round the one closed panel, its rim and its floor's edge: 9.5 px apart on its upper edge and 11.5 on its front edge; ± 2 px
About as far across as the panel is deep: a wall near 45 degrees, as on the 30-round (0.026 in).
A side panel's corners, their radius at the middle of the wall0.08 in ± 0.02 in 2 mmProvisionalWorked out: {magpul-pmag-30-gen-m3.side_panel_corner_radius}
Worked out 0.08 in ± 0.02 in used
{magpul-pmag-30-gen-m3.side_panel_corner_radius}
The 30-round GEN M3's, read on Magpul's photograph of that magazine, by reference: the same moulded panels. This magazine's patent draws its closed panel's corners at about 0.06 in (a tile of FIG. 3, not measured closer), inside that reading's ±.
The dot matrix's squares, their depth0.016 in ± 0.01 in 0.4 mmCorroboratedWorked out: 0.6 * {.side_panel_depth}
Worked out 0.016 in ± 0.01 in used
0.6 * {.side_panel_depth}
Sunk: on Magpul's photo of this magazine each square is dark along its upper edge, as the sunk panels' upper walls are (and as the block under the catch notch, which stands, is along its lower one); 'a paint pen dot matrix ... to allow easy marking', Magpul's sheet: places for paint. HOW DEEP IS ASSUMED: no view on file shows a square in profile. Six tenths of this magazine's own panels' depth, as the 30-round GEN M3's model has its dimples (that part's script: their walls' shadows on Magpul's photo of that magazine are that much weaker than the panels').
The dot matrix: a square across, wall to wall0.068 in ± 0.008 in 1.7 mmConflictWorked out: {magpul-pmag-30-gen-m3.dot_matrix_dimple}
Photo 0.086 in ± 0.007 in
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2071 px: 369.8 px/in. Read by the smallest rectangle round the white inside each of the sixty drawn squares, out by half the stroke: 31.1 to 33.1 px, 31.8 the middle value; the right elevation's sixty: 31.2 of 362.1 px/in, the same
Worked out 0.068 in ± 0.008 in used
{magpul-pmag-30-gen-m3.dot_matrix_dimple}
The 30-round GEN M3's, read on Magpul's photograph of that magazine: the same matrix (four blocks of three by five a side at a tenth of an inch; this one's pitch is 0.099 on its patent).
A photograph of the moulded squares against a drawing of them: the drawing's are drawn out to a heavy stroke, and this magazine's own photograph has the lands the smaller figure leaves. The drawing's figure stays.
patent and gen-m3 differ by 0.018 in beyond what each states it is good to.
Where each square is, is this magazine's own patent's (profiles.left and profiles.side, features `dots`); how big one is, is the 30-round's reading. The patent draws each square with a heavy stroke, the squares nearly touching (0.086 in to the stroke's middle at a pitch of 0.099, the white inside the stroke 0.0725); Magpul's photo of this magazine (184 px to the inch) has them apart by lands about a third of the pitch, as the 30-round's figure gives, and is too coarse to size one.
The dot matrix's squares on each side60CorroboratedPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi
Photo 60 count used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi, harvested
Scale: a count. Read by the closed white areas inside the small drawn squares, labelled and counted: 60, each 652 to 673 px
Photo 60 count
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: a count. Read by the same count on the right side elevation: 60, each 597 to 669 px
The two sides agree.
Four groups, each three across and five down, on each side. Each side is drawn from its own elevation, and the two are each other's mirror within 0.006 in (the groups' rearmost squares 0.686 and 0.689 in ahead of the spine's rear face, their foremost 1.97 and 1.98).
The bars across the front strip10ProvisionalPhoto: US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi
Photo 10 count used
US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi, harvested
Scale: a count. Read by the pairs of lines down the strip's middle (columns 800 and 850, rows 1780 to 2410): five between the frame's upper band and its middle one, five between that and the floorplate
Two rows of five, one in each row of the grip frame.
The bars across the spine under the stop10ProvisionalPhoto: US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi
Photo 10 count used
US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: a count. Read by the pairs of lines down columns 1650 and 1760 (either side of the rib), rows 1880 to 2545: five beside the rib, five under the band
Two rows of five. In the upper row the long rib down the spine's middle stands over them, and from the side they are behind it.
A bar of the front strip or the spine, its thickness along the magazine0.034 in ± 0.006 in 0.9 mmCorroboratedPhoto: US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi
Photo 0.034 in ± 0.006 in used
US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in. Read by a bar's two lines, the middles of their strokes: 12 to 13 px apart on all ten (12.5 the middle value); ± 2 px
Photo 0.033 in ± 0.006 in
US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in. Read by the same on the spine's ten: 10 to 12.5 px (12 the middle value)
The two elevations agree within a pixel; the front one has the more even lines.
The 30-round GEN M3's own read 0.034 in on its patent (its ledger): the same bars.
The front strip: the flat of the grip frame's front face that the bars lie across0.437 in ± 0.01 in 11.1 mmProvisionalPhoto: US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi
Photo 0.437 in ± 0.01 in used
US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in. Read by the strip's two edge lines on rows 1820 to 2366, columns 752 and 912.5: 160.5 px; the bars themselves run from 756 to 908.5 (0.415 in); ± 2 px and the scale
The 30-round GEN M3's is 0.44 in on its own patent.
The long rib down the spine's middle (upper row), and the stop's gusset over it0.148 in ± 0.01 in 3.8 mmProvisionalPhoto: US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi
Photo 0.148 in ± 0.01 in used
US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in. Read by the rib's two sides on rows 1890 to 2010, columns 1675.5 and 1730: 54.5 px (inside them the two lines of its face's edges, 1682.5 and 1723); ± 2 px and the scale
The 30-round GEN M3's is 0.151 in on its own patent.
The front strip's bars, how far they stand out of the strip0.014 in ± 0.006 in 0.4 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi
Photo 0.014 in ± 0.006 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 3 left side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2071 px: 369.8 px/in. Read by the first bar of the upper row on rows 1838 and 1844: its outer line at column 881.5, the front edge's own at 886.5 (the middles of the ink's runs): 5 px; ± 2 px
Worked out 0.017 in ± 0.004 in
{magpul-pmag-30-gen-m3.front_bar_proud}
The 30-round GEN M3's own, by reference: one generation's front strip.
This magazine's own drawing; the 30-round's reading is 0.003 in more, inside both ±.
Read on this magazine's own patent, where a bar shows in the side elevation as a small square across the front edge's line; the 30-round's, on Magpul's photograph of that magazine, is within a line's weight of it.
The spine's bars, how far they stand out of the spine0.022 in ± 0.006 in 0.6 mmCorroboratedWorked out: {magpul-pmag-30-gen-m3.spine_bar_proud}
Worked out 0.022 in ± 0.006 in used
{magpul-pmag-30-gen-m3.spine_bar_proud}
Not read on this magazine: its side elevations have the spine's lower row as a ripple of 0.01 to 0.025 in in the traced outline and its upper row as the rib's straight face, and no bar's own outline there. The 30-round GEN M3's, by reference (the same spine under the stop: its rib is 0.151 in wide for this one's 0.148, its bars as thick). The rib stands as far as the bars, as there.
The grip frame's front corners: how far behind the front face a side begins to turn in0.117 in ± 0.01 in 3 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi
Photo 0.117 in ± 0.01 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well, y from the feed lips' top (the side trace's own placement of the figure). Read by across the upper row on rows 1880 to 2080: the thin line inside the front panel 41.5 to 43 px behind the front edge's own line; across the lower row 44.5 and 46 px on two rows; ± 3 px
Worked out 0.115 in ± 0.012 in
{magpul-pmag-30-gen-m3.front_corner_depth}
The 30-round GEN M3's own, on its own patent, by reference.
This magazine's own drawing; the 30-round's is 0.002 in from it.
With front_strip_width, the round of the frame's front corners: a side runs forward flat to this far behind the front strip and then turns in to the strip's edge. No view has the turn in section; it is drawn as a quarter of an ellipse between the two, as the 30-round's is (ASSUMED: the front elevation has three lines down it, at 0.354, 0.390 and 0.422 in from the middle, where the 30-round's patent has its three at 0.358, 0.397 and 0.426).
The grip frame's rear: the width over the two shoulders beside the spine, where the rounds into the sides begin0.545 in ± 0.012 in 13.8 mmProvisionalPhoto: US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi
Photo 0.545 in ± 0.012 in used
US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in. Read by the strongest line outside the spine's on each side, columns 1602.5 and 1802.75 on rows 1920 to 2100 (the spine's own edges are at 1622.5 and 1782); ± 2 px each
Worked out 0.554 in ± 0.012 in
{magpul-pmag-30-gen-m3.rear_shoulder_width}
The 30-round GEN M3's own, on its own patent, by reference.
This magazine's own drawing; the 30-round's is 0.009 in more, inside both ±.
The spine's strip in the grip frame: how far it stands behind the shoulder beside it0.072 in ± 0.012 in 1.8 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi
Photo 0.072 in ± 0.012 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well, y from the feed lips' top (the side trace's own placement of the figure). Read by on rows 1980, 2030 and 2080 the first line ahead of the outline's rear edge is 33.3 to 34.1 px from it (0.094 in); the edge there is the long rib's face, which stands a bar's height behind the strip (spine_bar_proud, 0.022 in): 0.072 from the strip; ± 3 px
Worked out 0.07 in ± 0.012 in
{magpul-pmag-30-gen-m3.spine_strip_proud}
The 30-round GEN M3's own, on its own patent, by reference.
This magazine's own drawing; the 30-round's is 0.002 in from it.
Between the bands the rear panel runs round the rear corner onto a shoulder, and the spine's strip stands behind it by this.
The grip frame's rear corners: from the shoulder beside the spine to where a side begins to turn in0.124 in ± 0.015 in 3.1 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi
Photo 0.124 in ± 0.015 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well, y from the feed lips' top (the side trace's own placement of the figure). Read by the same three rows: the third line ahead of the rear edge at 78.8 to 79.6 px (0.218 in; 0.196 from the strip), less the shoulder's 0.072; in the lower row, where the edge is the strip's own teeth, the one line ahead of it is 73 to 74 px off (0.203 in) on rows 2300, 2360 and 2420; ± 4 px
Worked out 0.12 in ± 0.015 in
{magpul-pmag-30-gen-m3.rear_corner_depth}
The 30-round GEN M3's own, on its own patent, by reference.
This magazine's own drawing; the 30-round's is 0.004 in less, inside both ±.
With rear_shoulder_width, the round of the frame's rear corners, drawn as a quarter of an ellipse (ASSUMED, as the front's).
The spine (the rib down the rear that runs in a well's slot), its width0.438 in ± 0.012 in 11.1 mmProvisionalPhoto: US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi
Photo 0.438 in ± 0.012 in used
US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in. Read by the spine's two side lines on rows 1500 to 1740, columns 1621.5 and 1782.5: 161 px; outside each a thinner line 14 px off (the round at its foot); ± 2 px and the scale
A standard well's slot for it is .470 wide (std.ar15.magwell_spine_slot_width).
The spine, how far it stands behind the body's rear face0.139 in ± 0.01 in 3.5 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi
Photo 0.139 in ± 0.01 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well, y from the feed lips' top. Read by on rows 940 to 1740 the outline's rear line (the spine's rear face) at column 685.5 to 686.5 and the heavy line of the body's rear face at 735.5 to 736.5: 50 px; two thinner lines between them (706.5, 722) are edges on the spine's side; ± 2 px and the scale
A standard well's slot for it is .155 deep (std.ar15.magwell_length less magwell_box_length). The body ahead of it is then 2.36 in, in a box of 2.398.
The over-travel stop's tip, behind the spine's rear face0.061 in ± 0.01 in 1.5 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi
Photo 0.061 in ± 0.01 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: scale from magpul-pmag-20-gen-m3.overall_height = 5.6 in (y-extent 2028 px → 362.1 px/in). Read by −x_min of the traced outline (tools/trace.py); the outline's rearmost point, the tip of the over-travel stop on the spine, behind the spine's rear face in the well (the frame's x = 0)
Front to back over everything, the stop's tip to the floorplate's front2.993 in ± 0.054 in 76 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi
Photo 2.993 in ± 0.054 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: scale from magpul-pmag-20-gen-m3.overall_height = 5.6 in (y-extent 2028 px → 362.1 px/in). Read by width of the traced outline (tools/trace.py); the whole outline front to back: from the stop's tip to the floorplate's front
Width (side to side) of the top section, where it stands in the well0.902 in ± 0.02 in 22.9 mmConflictPhoto: US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi
Photo 0.902 in ± 0.02 in used
US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi, harvested
Scale: scale from magpul-pmag-20-gen-m3.overall_height = 5.6 in (y-extent 2059 px → 367.7 px/in). Read by median row width in y [-2.2, -0.7] (0.892–0.955) of the traced outline (tools/trace.py); the top section's width where it stands in the well, clear of the block under the catch notch (the median row)
Photo 0.9 in ± 0.018 in
US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in. Read by median row width in y [-2.2, -0.7] (0.891–0.953) of the rear elevation's traced outline (tools/trace.py, the `rear` spec)
Published “Dimensions (LxWxH): 5.7" x 2.6" x 0.87"”
T.REX ARMS, Magpul AR/M4 PMAG: Technical Specifications, the PMAG 20 column, a seller, read Oct 13, 2026 the page, harvested Oct 13, 2026
The third of a seller's three figures, the same for the 20, the 30 and the 40; what it runs between isn't said.
The model is this part's own patent's elevations scaled by its published height, and the two elevations agree. The seller's figure is 0.03 in less and stays: nothing on file says which is the body's own width.
patent and trex differ by 0.032 in beyond what each states it is good to.
patent-rear and trex differ by 0.03 in beyond what each states it is good to.
Magpul gives none. This magazine's own patent's front and rear elevations, each scaled by the height, agree; the one seller's figure is 0.03 in less, and is what a body that goes into a .898 in well with room would be. The model is the patent's (0.004 in over the well's own width: a line's weight of the drawing, or the height's ±).
Width of the gripping section, over its ribs and bands0.96 in ± 0.02 in 24.4 mmProvisionalPhoto: US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi
Photo 0.96 in ± 0.02 in used
US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi, harvested
Scale: scale from magpul-pmag-20-gen-m3.overall_height = 5.6 in (y-extent 2059 px → 367.7 px/in). Read by median row width in y [-4.4, -3.2] (0.936–0.968) of the traced outline (tools/trace.py); the gripping section's width over its ribs and bands (the median row)
Width of the floorplate, its widest1.104 in ± 0.021 in 28 mmProvisionalPhoto: US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi
Photo 1.104 in ± 0.021 in used
US D691,233 S (Magpul), FIG. 6 front elevation, 300 dpi, harvested
Scale: scale from magpul-pmag-20-gen-m3.overall_height = 5.6 in (y-extent 2059 px → 367.7 px/in). Read by width in y [-5.6, -4.9] of the traced outline (tools/trace.py); the floorplate, its widest
Hang below the magwell when seated2.912 in ± 0.12 in 74 mmProvisionalWorked out: {bad-workhorse-lower.magwell_bottom_center_y} - ({std.ar15.mag_catch_slot_bottom_y} + {std.ar15.mag_catch_slot_h} + {.catch_notch_top} - {.overall_height})
Worked out 2.912 in ± 0.12 in used
{bad-workhorse-lower.magwell_bottom_center_y} - ({std.ar15.mag_catch_slot_bottom_y} + {std.ar15.mag_catch_slot_h} + {.catch_notch_top} - {.overall_height})
Photo 2.8 in ± 0.11 in
Magpul's gallery 04.1: a whole rifle from its right side, square on, a black PMAG 20 seated in it; 1200 x 1200, harvested
Scale: the two receiver pins, 175 px apart: std.ar15.pin_spacing = 6.375 in gives 27.45 px/in. Read by the well's mouth at the middle of the well, row 664 (its rear end at row 669, its front at 659), down to the magazine's lowest point, its rear lower corner, row 741: 77 px; ± 1.5 px at each end and the pins' picks. The lower is not one on file: its mouth is its own
What the model does in the lower whose mouth is measured; Magpul's picture of one seated in another lower reads 0.11 in less, inside the two ±.
From the well's mouth at its middle down to the floorplate's lowest point, hung by its notch on the catch's upper face (the Army drawing's slot). The one lower on file whose mouth is measured is the Workhorse (its photo: bad-workhorse-lower.magwell_bottom_center_y, which carries no ±; the mouth rises 5.5 degrees toward the front, so the hang is more at the front of the well and less at its rear). A check on the seat, not what seats it. Magpul's own small picture of a 20 seated in a rifle is the second reading: a lower of no maker named, 27 px to the inch. In it the floorplate's lowest point is 4.90 in under the line of the two pins (134.5 px), where this seat puts it 4.98: 0.08 in, two of that picture's pixels.
Weight, loaded with 20 rounds (a seller's figure)12.5 oz ± 0.05 ozProvisionalPublished: T.REX ARMS, Magpul AR/M4 PMAG: Technical Specifications, the PMAG 20 column, a seller, read Oct 13, 2026
Published “Weight Loaded: 12.5 oz (355g)” used
T.REX ARMS, Magpul AR/M4 PMAG: Technical Specifications, the PMAG 20 column, a seller, read Oct 13, 2026 the page, harvested Oct 13, 2026
Which cartridge isn't said.
One round's share of the loaded weight0.42 oz ± 0.025 ozProvisionalWorked out: ({.weight_loaded} - {.weight}) / {.capacity}
Worked out 0.425 oz ± 0.025 oz used
({.weight_loaded} - {.weight}) / {.capacity}
What the loaded weight is worked out from in a build: the one seller's loaded figure (which cartridge isn't said) less Magpul's empty one, over its 20 rounds. By the seller's own pair (12.5 and 4.1 oz) it is 0.42; Magpul's own figures for its 60-round drum come to 0.425.
Length as the manufacturer states it (reference points undefined)5.6 in ± 0.05 in 142.2 mmConfirmedPublished: Magpul, PMAG 20 AR/M4 GEN M3 (MAG560), Technical Specifications, the maker, read Oct 13, 2026
Published “Length, max 5.6 in.” used
Magpul, PMAG 20 AR/M4 GEN M3 (MAG560), Technical Specifications, the maker, read Oct 13, 2026 the page, harvested Oct 13, 2026
Published “Dimensions (LxWxH): 5.7" x 2.6" x 0.87"”
T.REX ARMS, Magpul AR/M4 PMAG: Technical Specifications, the PMAG 20 column, a seller, read Oct 13, 2026 the page, harvested Oct 13, 2026
The first of a seller's three figures; what L, W and H run between isn't said (its PMAG 30 column has 7.5 in, Magpul's own figure for that one).
The maker's own figure.
Neither page says what it runs between. Magpul's is taken as the upright height (overall_height); the seller's tenth more is about what the same magazine is along the lean of its lower half, or over a dust cover: not settled, and kept.
Front to back as a seller states it (reference points undefined)2.6 in ± 0.05 in 66 mmProvisionalPublished: T.REX ARMS, Magpul AR/M4 PMAG: Technical Specifications, the PMAG 20 column, a seller, read Oct 13, 2026
Published “Dimensions (LxWxH): 5.7" x 2.6" x 0.87"” used
T.REX ARMS, Magpul AR/M4 PMAG: Technical Specifications, the PMAG 20 column, a seller, read Oct 13, 2026 the page, harvested Oct 13, 2026
The second of T.REX ARMS' three figures, the same for the 20, the 30 and the 40: more than the top section's front to back (2.50 in by this part's patent) and what that is with the stop on its spine (2.56); the whole outline over the floorplate's lean is 2.99 (depth_overall). A check on the outline, not a dimension the model is built from.
Width (side to side) as a seller states it (reference points undefined)0.87 in ± 0.005 in 22.1 mmProvisionalPublished: T.REX ARMS, Magpul AR/M4 PMAG: Technical Specifications, the PMAG 20 column, a seller, read Oct 13, 2026
Published “Dimensions (LxWxH): 5.7" x 2.6" x 0.87"” used
T.REX ARMS, Magpul AR/M4 PMAG: Technical Specifications, the PMAG 20 column, a seller, read Oct 13, 2026 the page, harvested Oct 13, 2026
The third of T.REX ARMS' three figures, the same for the 20, the 30 and the 40: the body where it stands in the well, by its size (a standard well is .898 wide inside). Magpul states no width.
Capacity20ConfirmedPublished: Magpul, PMAG 20 AR/M4 GEN M3 (MAG560), Technical Specifications, the maker, read Oct 13, 2026
Published “Capacity 20 rounds” used
Magpul, PMAG 20 AR/M4 GEN M3 (MAG560), Technical Specifications, the maker, read Oct 13, 2026 the page, harvested Oct 13, 2026
The body above the grip frame: how far behind the front face its sides begin to lean in0.602 in ± 0.012 in 15.3 mmProvisionalWorked out: {magpul-pmag-30-gen-m3.nose_taper_length}
Worked out 0.602 in ± 0.012 in used
{magpul-pmag-30-gen-m3.nose_taper_length}
The 30-round GEN M3's, by reference (the same moulded top section, where both stand in a well). This magazine's own drawing bears it out: US D691,233 FIG. 2 (57d9f77b9610, 362.1 px/in) has the line where the lean begins at column 1375 to 1376.5 on rows 1010 to 1302 (between the two ribs) and the front edge's line at 1589 to 1590: 214 px, 0.591 in, ± 3 px (0.008): inside the two readings' ±. The line bows forward toward its ends (0.582 in at row 800, 0.567 at row 1519): drawn straight.
The upper body narrows toward its front face: each side leans in from this far back to nose_shoulder_width, then rounds into a front face nose_front_width wide (nose_round_depth). The two guide ribs (guide_rib_*) and the tab on the frame's upper edge (frame_tab_*) are what the lean leaves at the side's own width. Detail pass, 2026-10-13.
The body above the grip frame: how far behind the front face the lean ends and the round into the front begins0.068 in ± 0.01 in 1.7 mmProvisionalWorked out: {magpul-pmag-30-gen-m3.nose_round_depth}
Worked out 0.068 in ± 0.01 in used
{magpul-pmag-30-gen-m3.nose_round_depth}
The 30-round GEN M3's, by reference (the same moulded top section, where both stand in a well). This magazine's own drawing bears it out: FIG. 2 (57d9f77b9610) has the thin line at column 1565.5 on eleven rows from 849 to 1650 and the front edge's at 1589 to 1590: 24 px, 0.066 in, ± 2 px.
The body above the grip frame: its width where the lean ends0.7 in ± 0.012 in 17.8 mmProvisionalWorked out: {magpul-pmag-30-gen-m3.nose_shoulder_width}
Worked out 0.7 in ± 0.012 in used
{magpul-pmag-30-gen-m3.nose_shoulder_width}
The 30-round GEN M3's, by reference (the same moulded top section, where both stand in a well). This magazine's own drawing bears it out: FIG. 6 (b1e83c27171f, 367.7 px/in) has the pair of lines at columns 704 and 959.5 on rows 1080 to 1330 (between the ribs): 255.5 px, 0.695 in, ± 3 px (0.008).
The body above the grip frame: the flat of its front face0.526 in ± 0.012 in 13.4 mmProvisionalWorked out: {magpul-pmag-30-gen-m3.nose_front_width}
Worked out 0.526 in ± 0.012 in used
{magpul-pmag-30-gen-m3.nose_front_width}
The 30-round GEN M3's, by reference (the same moulded top section, where both stand in a well). This magazine's own drawing bears it out: FIG. 6 (b1e83c27171f) has the inner pair of lines at columns 736 and 928.5 on the same rows: 192.5 px, 0.524 in, ± 3 px. (The silhouette there, the plain sides, is at 666.25 and 997: 0.900 in across the lines' middles.)
The upper guide rib on the upper body's front: how steeply its upper face rises as it goes in from the side29° ± 3°ProvisionalWorked out: {magpul-pmag-30-gen-m3.guide_rib_top_angle}
Worked out 29 deg ± 3 deg used
{magpul-pmag-30-gen-m3.guide_rib_top_angle}
The 30-round GEN M3's, by reference (the same moulded top section, where both stand in a well). This magazine's own drawing bears it out: FIG. 6 (b1e83c27171f) has the upper rib's upper face on rows 839, 833, 827.5, 822, 817, 811 at columns 680 to 730 (10 apart) on one side, 29.2 degrees, and 844, 836.5, 831, 825, 820, 814.5 at columns 990 to 940 on the other, 30.5 degrees; ± 2 degrees.
Each rib keeps the side's own width to the front face where the body leans in round it: a flat face flush with the side and faces that slope toward the middle, so that from the side it shows as a wedge growing toward the front. The upper rib's lower face is level (FIG. 6: row 890.5 on every column from 680 to 730); the lower rib's two faces both slope (guide_rib_lower_angle).
The upper guide rib: its flat face's upper edge, below the feed lips' top0.48 in ± 0.008 in 12.2 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi
Photo 0.48 in ± 0.008 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure. Read by down columns 1420 to 1560 (five of them): the solid line at row 896.5 (896 to 898.5); the wedge's line over it runs from row 898.5 at column 1420 to 877.5 at column 1580 (0.052 in over the flat at the front); ± 3 px
This magazine's own design patent (it draws MAG560).
The upper guide rib: its flat face, from its upper edge to its lower0.133 in ± 0.008 in 3.4 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi
Photo 0.133 in ± 0.008 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure. Read by down the same columns: the solid lines at rows 896.5 and 944.5 (944.5 to 945): 48 px; a broken line runs 7.5 px inside each (904, 952); ± 3 px
This magazine's own design patent (it draws MAG560).
The lower guide rib: its flat face's upper edge, below the feed lips' top1.996 in ± 0.008 in 50.7 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi
Photo 1.996 in ± 0.008 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure. Read by down columns 1420 to 1560: the solid line at row 1445.5 (1445.5 to 1446.5); the wedge's line over it runs from 1442.5 at column 1420 to 1428 at column 1580; ± 3 px
This magazine's own design patent (it draws MAG560).
The lower guide rib: its flat face, from its upper edge to its lower0.102 in ± 0.008 in 2.6 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi
Photo 0.102 in ± 0.008 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure. Read by down the same columns: the solid lines at rows 1445.5 and 1482.5 (1482.5 to 1484): 37 px; under it a second wedge's line runs from 1484 at column 1420 to 1500 at column 1580; ± 3 px
This magazine's own design patent (it draws MAG560).
The lower guide rib: how steeply its upper face rises and its lower face falls as they go in from the side19° ± 3°ProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 6 front elevation, 300 dpi
Photo 19 deg ± 3 deg used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 6 front elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px: 367.7 px/in; across from the figure's own middle column (831.9: the mean of three pairs of lines, 831.6, 831.75 and 832.25). Read by the lower rib on one side, columns 680 to 730: its upper face on rows 1391.5, 1387.5, 1382.5, 1380.5, 1376.5, 1374.5 (18.8 degrees) and its lower on 1438.5, 1440.5, 1444, 1447.5, 1451, 1455 (18.3); on the other side, columns 990 to 950: 1394, 1389.5, 1386.5, 1382.5, 1379 (20.6) and 980 to 940: 1438.5, 1441.5, 1445.5, 1448.5, 1452 (18.7); one figure for both faces; ± covers the four
This magazine's own design patent (it draws MAG560).
Unlike the upper rib (and unlike the 30-round's two, as that part's ledger has them) the lower rib is a wedge both ways: FIG. 2 has a wedge's line above its flat face and another below, and FIG. 6 both faces sloping.
The tab on the grip frame's upper edge: its top, below the feed lips' top2.312 in ± 0.01 in 58.7 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi
Photo 2.312 in ± 0.01 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure. Read by down columns 1450, 1480 and 1500: the heavy line of its top at rows 1562.5, 1560 and 1558 to 1563 (a second line 9 px under it); 1560 taken; ± 3 px
This magazine's own design patent (it draws MAG560).
The tab stands up from the frame's upper edge near the front, about half an inch high. Like the ribs it is a piece of the side at the side's own width where the side leans in: FIG. 6 (b1e83c27171f, rows 1560 to 1640) has its face on the silhouette at columns 665 and 998.5, 0.4535 in from the middle, as the plain side over it is (0.450), with its inner edges at 0.419 and 0.3875 (the 30-round's: 0.425 and 0.394).
The tab on the grip frame's upper edge: its front side at its top, behind the upper body's front face0.2 in ± 0.01 in 5.1 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi
Photo 0.2 in ± 0.01 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure. Read by its front side's heavy line at columns 1519.5, 1523.5 and 1526 on rows 1600, 1650 and 1700 (a thinner line 9 px inside it), carried up to its top at row 1560: 1517; the front edge's line at 1589.5: 72.5 px; ± 3 px
This magazine's own design patent (it draws MAG560).
The tab on the grip frame's upper edge: front to back0.226 in ± 0.01 in 5.7 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi
Photo 0.226 in ± 0.01 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure. Read by between the heavy lines of its two sides on rows 1600, 1650 and 1700: 1438 to 1519.5, 1441.5 to 1523.5, 1444 to 1526: 81.5 to 82 px; ± 3 px
This magazine's own design patent (it draws MAG560).
The tab on the grip frame's upper edge: how far its sides lean forward as they go down3.6° ± 1°ProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi
Photo 3.6 deg ± 1 deg used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure. Read by its rear side's line at columns 1438, 1441.5, 1444 and its front side's at 1519.5, 1523.5, 1526 on rows 1600, 1650, 1700: 6 and 6.5 px forward over 100 rows; ± 1 degree is a pixel at either end
This magazine's own design patent (it draws MAG560).
The tab on the grip frame's upper edge, the round of its two upper corners0.03 in ± 0.015 in 0.8 mmProvisionalWorked out: {magpul-pmag-30-gen-m3.frame_tab_corner_radius}
Worked out 0.03 in ± 0.015 in used
{magpul-pmag-30-gen-m3.frame_tab_corner_radius}
The 30-round GEN M3's, read on Magpul's photograph of that magazine, by reference. NOT read on this magazine: its patent's FIG. 2 draws the tab's upper corners round (the top's line and each side's meet over about 10 px, 0.03 in, by eye on a tile), and Magpul's photo of the 20 is too coarse (184 px to the inch) to say more.
The body above the grip frame: the round of its rear corners, from the body's rear face beside the spine into the side0.057 in ± 0.012 in 1.4 mmCorroboratedWorked out: {magpul-pmag-30-gen-m3.upper_rear_corner_radius}
Worked out 0.057 in ± 0.012 in used
{magpul-pmag-30-gen-m3.upper_rear_corner_radius}
The 30-round GEN M3's, by reference (the same moulded top section, where both stand in a well). This magazine's own drawing bears it out: FIG. 7 (the rear elevation on sheet b1e83c27171f, 368.2 px/in, its middle column 1703) has a line at columns 1559.5 and 1846.5 inside the silhouette's 1537.5 and 1868.5 on rows 1000 to 1330: 22 px, 0.060 in; FIG. 2 (57d9f77b9610) has the body's rear face at column 736.5 (spine_depth) and the next line at 754.5: 18 px, 0.050 in; ± 3 px each.
The slim groove near the spine: its middle, ahead of the spine's rear face0.415 in ± 0.008 in 10.5 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi
Photo 0.415 in ± 0.008 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure. Read by its two heavy lines at columns 827 (825.5 to 829.5) and 844.5 (843 to 845.5) on eighteen rows from 800 to 1120, a thin line at 840.5 between them: their middle at 835.75; ± 3 px
This magazine's own design patent (it draws MAG560).
A slim groove with round ends runs down each side of the upper body near the spine, from under the top to about the height of the catch's window. Read on the right side elevation; Magpul's photo of the left side (7322951944be) shows the same groove there (seen, not measured: the photo is 184 px to the inch and the groove 9 px wide), and the left's is drawn as the right's mirrored. HOW DEEP IS ASSUMED: it breaks no outline in any view on file. Drawn with walls leaning as far across as it is deep, to a floor a quarter of its width (0.018 in). Detail pass, 2026-10-13.
The slim groove near the spine: across, between its two edges0.048 in ± 0.008 in 1.2 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi
Photo 0.048 in ± 0.008 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure. Read by between the middles of its two heavy lines, columns 827 and 844.5, on the same rows: 17.5 px; each line is 4 to 5 px heavy, which the ± covers
This magazine's own design patent (it draws MAG560).
The slim groove near the spine: its upper end, below the feed lips' top0.176 in ± 0.008 in 4.5 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi
Photo 0.176 in ± 0.008 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure. Read by down columns 830 and 835: the top of its round end at rows 786.5 and 787 (down column 827 its line begins at 786.5); ± 3 px
This magazine's own design patent (it draws MAG560).
The slim groove near the spine: from its upper end to its lower0.938 in ± 0.01 in 23.8 mmProvisionalPhoto: US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi
Photo 0.938 in ± 0.01 in used
US D691,233 S (Magpul, 'Magazine for a firearm'), FIG. 2 right side elevation, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2028 px: 362.1 px/in; x from the spine's rear face in the well (column 685.5), y from the feed lips' top (row 722.7): the side trace's own placement of the figure. Read by down columns 835 and 840: its lower round end at rows 1126 and 1125.5, its upper at 786.5: 339.5 px; ± 3 px
This magazine's own design patent (it draws MAG560).
The over-travel stop on the spine: half the width of its rear face where it is flat, before its corners round off0.287 in ± 0.015 in 7.3 mmProvisionalPhoto: US D691,233 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi
Photo 0.287 in ± 0.015 in used
US D691,233 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi, harvested
Scale: the sheet's own scale: its two plans' widest rows (FIG. 4 row 1630, 381 px; FIG. 5 row 1763, 384 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.552 in): 346.5 px/in, ± 1% (FIG. 4's length, rows 1194 to 2219 over the side outline's 2.994 in, reads 1.2% smaller); across from each figure's own middle (FIG. 4 column 853.4, FIG. 5 column 1667.5). Read by FIG. 4: the rear edge's line on row 1195, one pixel ahead of the edge, from column 756 to 955 (99.5 px each side of the middle); ± 4 px, the line being drawn in dashes there
This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan).
Photo 0.297 in ± 0.015 in
US D691,233 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi, harvested
Scale: the sheet's own scale: its two plans' widest rows (FIG. 4 row 1630, 381 px; FIG. 5 row 1763, 384 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.552 in): 346.5 px/in, ± 1% (FIG. 4's length, rows 1194 to 2219 over the side outline's 2.994 in, reads 1.2% smaller); across from each figure's own middle (FIG. 4 column 853.4, FIG. 5 column 1667.5). Read by FIG. 5: the same edge on row 1196, its two ends at columns 1564.5 and 1770.5 (103 px each side); ± 4 px
This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan).
The view from above, where the ledge's top edge is the outline; the two plans agree within their ±.
The stop is a ledge standing out behind the spine at the grip frame's top (the anchor's note: its tip is stop_behind_spine behind the spine's face), what the magazine stops against under a well: seen from above and below its rear face is flat across the middle, its corners round, and its sides lean out going forward until they meet the frame's top band. The 30-round GEN M3's patent draws the same ledge (magpul-pmag-30-gen-m3.stop_*), within 0.02 in of these figures.
The over-travel stop: how far its sides lean out from the magazine's length, going forward from its rounded corners18.4° ± 1.7°ProvisionalPhoto: US D691,233 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi
Photo 18.4 deg ± 1.7 deg used
US D691,233 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi, harvested
Scale: the sheet's own scale: its two plans' widest rows (FIG. 4 row 1630, 381 px; FIG. 5 row 1763, 384 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.552 in): 346.5 px/in, ± 1% (FIG. 4's length, rows 1194 to 2219 over the side outline's 2.994 in, reads 1.2% smaller); across from each figure's own middle (FIG. 4 column 853.4, FIG. 5 column 1667.5). Read by FIG. 4: the outline's outer edge, both sides, on rows 1215 to 1263 (21 to 69 px behind the rear edge, row 1194): 127.0, 129.75, 131.5, 133.75, 135.5, 137.5, 139.25, 141.25, 143.0 px from the middle: 16 px out over 48 px along (0.333); FIG. 5 the same within 2 px; ± 1 px a reading
This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan).
Each side is straight from where its corner's round ends to where it meets the frame's top band (stop_length), out to stop_half_width there.
The over-travel stop: half its widest, where its sides meet the frame's top band0.426 in ± 0.008 in 10.8 mmCorroboratedPhoto: US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi
Photo 0.426 in ± 0.008 in used
US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in; across from the figure's own middle column (1702.75, between the frame's silhouette lines 1528 and 1877.5, and the rib's). Read by FIG. 7: the ledge's two end lines, columns 1545 to 1547 and 1859.5 on rows 1762 to 1798 (156.75 px each side of the middle); ± 2 px
This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan).
Photo 0.423 in ± 0.012 in
US D691,233 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi, harvested
Scale: the sheet's own scale: its two plans' widest rows (FIG. 4 row 1630, 381 px; FIG. 5 row 1763, 384 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.552 in): 346.5 px/in, ± 1% (FIG. 4's length, rows 1194 to 2219 over the side outline's 2.994 in, reads 1.2% smaller); across from each figure's own middle (FIG. 4 column 853.4, FIG. 5 column 1667.5). Read by FIG. 4: the side's line where it meets the band's (rows 1269 to 1275: 145.75 to 151.75 px from the middle, its run ending at 146.5); ± 3 px
This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan).
The view that looks across the ledge's widest; the plan agrees within the two readings' ±.
The rear elevation sees it as the ledge's two ends, inside the frame's silhouette: the stop is narrower than the frame.
The over-travel stop: how far forward of its rear face its sides run before they meet the frame's top band0.224 in ± 0.01 in 5.7 mmProvisionalPhoto: US D691,233 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi
Photo 0.224 in ± 0.01 in used
US D691,233 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi, harvested
Scale: the sheet's own scale: its two plans' widest rows (FIG. 4 row 1630, 381 px; FIG. 5 row 1763, 384 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.552 in): 346.5 px/in, ± 1% (FIG. 4's length, rows 1194 to 2219 over the side outline's 2.994 in, reads 1.2% smaller); across from each figure's own middle (FIG. 4 column 853.4, FIG. 5 column 1667.5). Read by FIG. 4: the side's straight run ends between rows 1269 and 1275 (75 and 81 px behind the rear edge: 145.75 then 151.75 px out, against a third of a pixel a row before), 77.5 px; FIG. 5 the same (rows 1269 to 1275: 144.5 then 152.5); ± 3 px
This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan).
The over-travel stop: how far down its rear face comes in the middle, under the ledge's top where it meets the spine0.174 in ± 0.01 in 4.4 mmProvisionalPhoto: US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi
Photo 0.174 in ± 0.01 in used
US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in; across from the figure's own middle column (1702.75, between the frame's silhouette lines 1528 and 1877.5, and the rib's). Read by FIG. 7: the face's lower edge, the middle of its pair of lines, on columns 1652, 1754, 1629 and 1776 (rows 1815.5 to 1816 and 1823: 1819.4), against the ledge's top edge at row 1755.5 (columns 1606 to 1844); ± 3 px
This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan).
Each of the stop's depths is read under the ledge's top edge as the rear elevation draws it, its highest, where it meets the spine's face (FIG. 7's row 1755.5 is 2.963 in under the lips on the figure's own scale; the side outline's top crosses the spine's face at 2.972, falling to 3.01 at the tip, the ledge drawn rounded over). The rear face is deepest across the middle, shallower toward its ends: under the face, the stop is hollow either side of the gusset (stop_bay_half_width) and its outer parts slope up to the face's lower edge (stop_wing_*).
The over-travel stop: how far out from the middle its rear face keeps its middle depth0.262 in ± 0.03 in 6.7 mmProvisionalPhoto: US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi
Photo 0.262 in ± 0.03 in used
US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in; across from the figure's own middle column (1702.75, between the frame's silhouette lines 1528 and 1877.5, and the rib's). Read by FIG. 7: the face's lower edge at its middle depth out to columns 1606 and 1799 (rows 1814.5 to 1815 and 1823); at columns 1584 and 1822 it has risen to rows 1802.5 and 1810.5
This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan).
The over-travel stop: how far down its rear face comes toward its ends0.128 in ± 0.012 in 3.3 mmProvisionalPhoto: US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi
Photo 0.128 in ± 0.012 in used
US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in; across from the figure's own middle column (1702.75, between the frame's silhouette lines 1528 and 1877.5, and the rib's). Read by FIG. 7: the face's lower edge on columns 1561 and 1844 (rows 1798 to 1798.5 and 1806.5 to 1807: 1802.6), 47.1 px under the top edge; at columns 1584 and 1822, between the two, 0.139 in (a straight line between this and the middle depth has 0.151); at 1548 and 1857, 0.139; ± 3 px
This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan).
The over-travel stop: how far out from the middle the rear face's lower edge reaches stop_lip_depth_end0.385 in ± 0.01 in 9.8 mmProvisionalPhoto: US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi
Photo 0.385 in ± 0.01 in used
US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in; across from the figure's own middle column (1702.75, between the frame's silhouette lines 1528 and 1877.5, and the rib's). Read by FIG. 7: columns 1561 and 1844, where stop_lip_depth_end is read (141.5 px from the middle); outward of it the edge turns down into the ledge's rounded end
This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan).
The over-travel stop: under its outer parts, how far below the ledge's top the sloping underside comes at stop_wing_half_width0.169 in ± 0.015 in 4.3 mmProvisionalPhoto: US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi
Photo 0.169 in ± 0.015 in used
US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in; across from the figure's own middle column (1702.75, between the frame's silhouette lines 1528 and 1877.5, and the rib's). Read by FIG. 7: columns 1561 and 1844, the line at rows 1817 to 1818 under the face's lower edge's pair (the pair at 1838 and 1848 under it is the band's corner, as at the next columns in: 1849.5 and 1851.5), 62 px under the top edge; ± 4 px
This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan).
The rear elevation draws a second edge under each end of the face, coming down from near the ledge's end to the spine's edge where the frame's top band ends: the underside of the ledge's outer parts, which slopes down from the face's lower edge going forward. Drawn as ruled from the face's lower edge at the rear to a straight edge at the spine's face, from this point down to the spine's edge at the top of the first row (FIG. 7's edge reads 0.214 in under the top at columns 1584 and 1822 and 0.215 at 1606 and 1799, where that line has 0.19 and 0.21).
The over-travel stop: how far out from the middle stop_wing_depth is read0.385 in ± 0.01 in 9.8 mmProvisionalPhoto: US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi
Photo 0.385 in ± 0.01 in used
US D691,233 S (Magpul), FIG. 7 rear elevation, on the same sheet as FIG. 6, 300 dpi, harvested
Scale: magpul-pmag-20-gen-m3.overall_height = 5.6 in over the figure's 2059 px (rows 666 to 2725): 367.7 px/in; across from the figure's own middle column (1702.75, between the frame's silhouette lines 1528 and 1877.5, and the rib's). Read by FIG. 7: columns 1561 and 1844 (141.5 px from the middle)
This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan).
The over-travel stop: under it, how far out from the middle the hollow either side of the gusset reaches at the rear face0.28 in ± 0.015 in 7.1 mmProvisionalPhoto: US D691,233 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi
Photo 0.28 in ± 0.015 in used
US D691,233 S (Magpul), sheet 4: FIG. 4 top plan and FIG. 5 bottom plan, 300 dpi, harvested
Scale: the sheet's own scale: its two plans' widest rows (FIG. 4 row 1630, 381 px; FIG. 5 row 1763, 384 px: the floorplate) over the front elevation's floorplate width (profiles.front, 2 x 0.552 in): 346.5 px/in, ± 1% (FIG. 4's length, rows 1194 to 2219 over the side outline's 2.994 in, reads 1.2% smaller); across from each figure's own middle (FIG. 4 column 853.4, FIG. 5 column 1667.5). Read by FIG. 5: the wall's pair of lines, both sides, on rows 1215, 1221 and 1227 (21, 27, 33 px ahead of the rear edge, row 1194): (1577, 1586.5 | 1748, 1758), (1580.5, 1590.5 | 1743.5, 1754), (1582.5, 1594.5 | 1740.5, 1753): their middles 85.6, 81.6, 79.1 px from the middle; a line through them, 97.0 - 0.54 x px, at the rear edge; ± 3 px (the rows further forward run into the gusset's and the bars' lines)
This magazine's own design patent. Primary Arms' and Magpul's views of MAG560 show the ledge from the side and the front quarters only (a check on where it is, not on its shape in plan).
FIG. 5 (from below) draws each hollow's outer wall as a straight line from the rear face forward and in toward the spine's edge at the spine's face (it reaches the spine's half width, 0.219 in, 0.112 in ahead of the rear face). The hollow's roof is the face's lower edge in the middle (stop_lip_depth_middle).
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
AR-15 magazine well
- Lower receivers
- Aero Precision M4E1 complete lower, A2 grip and M4 stock, Aero Precision M4E1 Stripped Lower Receiver, Battle Arms Development Workhorse stripped lower, BCM MK2 AR-15 Lower Receiver, Bear Creek Arsenal BC-15 Multi Caliber, Lower Receiver, Black Anodized, Geissele Automatics Super Duty AR-15 Lower Receiver - Stripped Lower, Palmetto State Armory AR-15 "Stealth" Stripped Lower Receiver
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- KYGUNCO $11.99 Black Nov 21, 2026, in stock that day
- AR15Discounts $12.95 Black Nov 21, 2026, in stock that day
- Impact Guns $13.99 Black Nov 21, 2026, in stock that day
- T.REX ARMS $14.00 Black Nov 21, 2026, in stock that day
- Scheels $14.39 Black Oct 13, 2026, in stock that day
- Midwest Gun Works $14.95 Black Nov 21, 2026, in stock that day
- Aero Precision $14.95 Black Nov 21, 2026, stock not said
- Primary Arms $15.15 Black Nov 21, 2026, in stock that day
- Mile High Shooting Accessories $15.15 Black Nov 21, 2026, in stock that day
- Magpul $15.95 Nov 21, 2026, stock not said
- Sportsman's Warehouse $15.99 Black Nov 21, 2026, in stock that day
- Academy Sports + Outdoors $15.99 Black Nov 20, 2026, in stock that day
- GRITR Sports $16.99 Black Nov 21, 2026, in stock that day
- Rifle Supply $17.99 Black Nov 21, 2026, in stock that day