Lower receiver
BCM MK2 AR-15 Lower Receiver
BCM's lower receiver as it comes in its MK2 complete lower: "Forged 7075-T6 aluminum construction", "Type III hardcoat anodized finish", "Multi-Caliber marked" (Primary Arms), its left side marked "BCM RIFLE COMPANY / MODEL BCM4 / CAL. MULTI" and "BRAVO COMPANY MFG. INC. / HARTLAND WISCONSIN / USA" (Primary Arms' photos). Its parts kit is installed (the pins, the selector, "Non-Ambi", the bolt catch, the magazine catch and their springs and detents) and so is BCM's polymer trigger guard ("Enlarged polymer trigger guard for gloved use", Primary Arms of the Mod 0 stock lower; "Enlarged trigger guard", of the blem). The trigger ("PNT (Polished Nickel Teflon) trigger"), the grip ("BCM ergonomic pistol grip"; "BCM Mod 4 pistol grip" on the blem's page) and the MK2 receiver extension with its "T0 buffer (3.8 oz)" are parts of their own in the complete lower's kit. "Ready for any compatible stock or pistol brace". The blem's page also says "Low shelf, compatible with RDIAS or Accu-Wedge" (the shelf at the fire-control pocket's rear: its inside is drawn as the Army drawing's).

- Weight
- 11.13 oz ± 0.8 oz Provisionalworked out: {.receiver_weight} + {.guard_weight} + {rise-lpk.weight}
- Lowest price
- Sold in the BCM MK2 AR-15 Lower Receiver - Complete Lower - No Stock, not by itself
- Colour
- Black (placeholder)
- Drawn as
- modelled
- Maker's page
- primaryarms.com
In “Drop-in 16 in, Stealth Gray on BCM's MK2 lower”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
The forging alone, by its metal8.53 oz ± 0.5 ozProvisionalWorked out: The receiver model's volume, 5.224 cubic inches (pipeline/blender/bcm_mk2_lower_receiver.py's manifest, app/public/models/bcm-mk2-lower-receiver.receiver.json volume_in3), times std.density.aluminium_7075 (1.632 oz to the cubic inch: "Forged 7075-T6 aluminum construction", Primary Arms): 8.53 oz. The ± is what the model draws without a reading: the body's width the drawing's, the roll's crest assumed, the well's walls as thick as the walls' width leaves them, the inside at the drawing's nominal sizes (about 0.3 cubic inches either way).
Worked out 8.53 oz ± 0.5 oz used
The receiver model's volume, 5.224 cubic inches (pipeline/blender/bcm_mk2_lower_receiver.py's manifest, app/public/models/bcm-mk2-lower-receiver.receiver.json volume_in3), times std.density.aluminium_7075 (1.632 oz to the cubic inch: "Forged 7075-T6 aluminum construction", Primary Arms): 8.53 oz. The ± is what the model draws without a reading: the body's width the drawing's, the roll's crest assumed, the well's walls as thick as the walls' width leaves them, the inside at the drawing's nominal sizes (about 0.3 cubic inches either way)., harvested
Worked out, not weighed: no page gives this forging's weight. The catalog's other forged mil-spec lowers come to 7.9 to 8.4 oz the same way and by their makers.
The trigger guard alone, by its polymer0.1 oz ± 0.04 ozProvisionalWorked out: The guard model's volume, 0.158 cubic inches (app/public/models/bcm-mk2-lower-receiver.guard.json volume_in3), times std.density.polymer (0.659 oz to the cubic inch, a polyamide's: BCM, "Made of impact resistant polymer", names no grade): 0.104 oz. The ± is a glass fill's and the ends' assumed reach between the ears; its roll pin and set screw aren't in it.
Worked out 0.104 oz ± 0.04 oz used
The guard model's volume, 0.158 cubic inches (app/public/models/bcm-mk2-lower-receiver.guard.json volume_in3), times std.density.polymer (0.659 oz to the cubic inch, a polyamide's: BCM, "Made of impact resistant polymer", names no grade): 0.104 oz. The ± is a glass fill's and the ends' assumed reach between the ears; its roll pin and set screw aren't in it., harvested
Worked out, not weighed: BCM's guard page has "weight":null in its own product data.
Trigger and hammer pin diameter0.154 in ± 0.0005 in 3.9 mmProvisionalPublished: Primary Arms, Bravo Company Manufacturing MK2 AR-15 Lower Receiver - Complete Lower - No Stock (LRG-RMS-NO-STOCK), Specifications, a seller, read Oct 28, 2026
Published “Trigger Pin Diameter MIL-SPEC .154” used
Primary Arms, Bravo Company Manufacturing MK2 AR-15 Lower Receiver - Complete Lower - No Stock (LRG-RMS-NO-STOCK), Specifications, a seller, read Oct 28, 2026 the page, harvested Oct 28, 2026
The same row on the blem's page and the Mod 0 stock lower's. The drawing's holes are .1555 to .1580 for these pins (std.ar15.fcg_pin_hole_d).
Receiver maximum width (Z)0.88 in ± 0.008 in 22.4 mmConfirmedWorked out: {std.ar15.lower_body_width}
Worked out 0.88 in ± 0.008 in used
{std.ar15.lower_body_width}, harvested
The body's width is the Army drawing's (Section C-C). A mil-spec pattern: Primary Arms of this lower, "ready for any Mil-Spec upper" (the Mod 0 stock lower's page) and "Trigger Pin Diameter MIL-SPEC .154"; BCM, of its parts kit, "all MIL SPEC lower receivers built per the USGI TDP". The drawing's figure (8448608).
No page states a width and no photo on file looks along the receiver. The body is the drawing's; the well's walls, the roll along the well's right top and the tower's ring stand wider.
Receiver extension (bore) axis above the takedown pin centre0.877 in ± 0.0015 in 22.3 mmConfirmedWorked out: {std.ar15.bore_axis_y}
Worked out 0.8775 in ± 0.0015 in used
{std.ar15.bore_axis_y}, harvested
A mil-spec pattern: Primary Arms of this lower, "ready for any Mil-Spec upper" (the Mod 0 stock lower's page) and "Trigger Pin Diameter MIL-SPEC .154"; BCM, of its parts kit, "all MIL SPEC lower receivers built per the USGI TDP". The drawing's figure (8448608).
Magazine seat, X (a seated magazine's frame origin ahead of the takedown pin)3.491 in ± 0.03 in 88.7 mmProvisionalWorked out: {bad-workhorse-lower.magazine_seat_x}
Worked out 3.4915 in ± 0.03 in used
{bad-workhorse-lower.magazine_seat_x}, from the site owner
Where a magazine seats in a mil-spec well, from the Army drawing's well and catch slot and the user's own magazine, recorded on the Workhorse (as the catalog's other mil-spec lowers take it). No photo of a magazine seated in this lower is on file; its catch's button is at the drawing's place on the right photo (3.247, -0.566 for 3.291, -0.565).
Magazine seat, Y (the feed-lip top of a seated magazine)1.003 in ± 0.05 in 25.5 mmProvisionalWorked out: {bad-workhorse-lower.magazine_seat_y}
Worked out 1.003 in ± 0.05 in used
{bad-workhorse-lower.magazine_seat_y}, from the site owner
As magazine_seat_x: the standard well's and the catch's.
Grip seat, Y (the underside a grip's flat top bears on, at the takedown pin's X)-1.069 in ± 0.011 in -27.2 mmConfirmedWorked out: {std.ar15.deck_y} - {std.ar15.grip_seat_below_deck}
Worked out -1.0695 in ± 0.0115 in used
{std.ar15.deck_y} - {std.ar15.grip_seat_below_deck}, harvested
The flat the lug hangs from, 1.318 below the deck: the drawing's. A mil-spec pattern: Primary Arms of this lower, "ready for any Mil-Spec upper" (the Mod 0 stock lower's page) and "Trigger Pin Diameter MIL-SPEC .154"; BCM, of its parts kit, "all MIL SPEC lower receivers built per the USGI TDP". The drawing's figure (8448608).
Photo -1.11 in ± 0.04 in
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1440, 634) on a gridded crop (scratch/crop.py), carried through that frame: the body's lower edge over the trigger's opening, where the opening's rear turns up
The grip hides the seat itself; the edge over the opening is the same plane on the drawing, and reads 0.04 below it here (the far wall's edge, from a lens a little above).
The drawing's; the photo's edge over the opening is 0.04 lower, within its ± and in the sense a lens above the part gives.
Trigger pin hole centre, X1.928 in ± 0.004 in 49 mmConfirmedWorked out: {std.ar15.trigger_pin_x}
Worked out 1.928 in ± 0.004 in used
{std.ar15.trigger_pin_x}, harvested
A mil-spec pattern: Primary Arms of this lower, "ready for any Mil-Spec upper" (the Mod 0 stock lower's page) and "Trigger Pin Diameter MIL-SPEC .154"; BCM, of its parts kit, "all MIL SPEC lower receivers built per the USGI TDP". The drawing's figure (8448608).
Photo 1.927 in ± 0.03 in
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1474, 578) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing
The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it.
Trigger pin hole centre, Y-0.689 in ± 0.004 in -17.5 mmConfirmedWorked out: {std.ar15.trigger_pin_y}
Worked out -0.689 in ± 0.004 in used
{std.ar15.trigger_pin_y}, harvested
A mil-spec pattern: Primary Arms of this lower, "ready for any Mil-Spec upper" (the Mod 0 stock lower's page) and "Trigger Pin Diameter MIL-SPEC .154"; BCM, of its parts kit, "all MIL SPEC lower receivers built per the USGI TDP". The drawing's figure (8448608).
Photo -0.691 in ± 0.03 in
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1474, 578) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing
The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it.
Hammer pin hole centre, X2.771 in ± 0.004 in 70.4 mmConfirmedWorked out: {std.ar15.hammer_pin_x}
Worked out 2.771 in ± 0.004 in used
{std.ar15.hammer_pin_x}, harvested
A mil-spec pattern: Primary Arms of this lower, "ready for any Mil-Spec upper" (the Mod 0 stock lower's page) and "Trigger Pin Diameter MIL-SPEC .154"; BCM, of its parts kit, "all MIL SPEC lower receivers built per the USGI TDP". The drawing's figure (8448608).
Photo 2.754 in ± 0.03 in
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1585.5, 538.5) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing
The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it.
Hammer pin hole centre, Y-0.375 in ± 0.004 in -9.5 mmConfirmedWorked out: {std.ar15.hammer_pin_y}
Worked out -0.375 in ± 0.004 in used
{std.ar15.hammer_pin_y}, harvested
A mil-spec pattern: Primary Arms of this lower, "ready for any Mil-Spec upper" (the Mod 0 stock lower's page) and "Trigger Pin Diameter MIL-SPEC .154"; BCM, of its parts kit, "all MIL SPEC lower receivers built per the USGI TDP". The drawing's figure (8448608).
Photo -0.384 in ± 0.03 in
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1585.5, 538.5) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing
The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it.
Selector hole centre, X0.803 in ± 0.004 in 20.4 mmConfirmedWorked out: {std.ar15.selector_x}
Worked out 0.803 in ± 0.004 in used
{std.ar15.selector_x}, harvested
A mil-spec pattern: Primary Arms of this lower, "ready for any Mil-Spec upper" (the Mod 0 stock lower's page) and "Trigger Pin Diameter MIL-SPEC .154"; BCM, of its parts kit, "all MIL SPEC lower receivers built per the USGI TDP". The drawing's figure (8448608).
Photo 0.813 in ± 0.03 in
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1325, 547) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing
The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it.
Selector hole centre, Y-0.466 in ± 0.004 in -11.8 mmCorroboratedWorked out: {std.ar15.selector_y}
Worked out -0.466 in ± 0.004 in used
{std.ar15.selector_y}, harvested
A mil-spec pattern: Primary Arms of this lower, "ready for any Mil-Spec upper" (the Mod 0 stock lower's page) and "Trigger Pin Diameter MIL-SPEC .154"; BCM, of its parts kit, "all MIL SPEC lower receivers built per the USGI TDP". The drawing's figure (8448608).
Photo -0.476 in ± 0.03 in
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1325, 547) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing
The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it.
Trigger guard rear ear hole, X1.498 in ± 0.005 in 38.1 mmConfirmedWorked out: {std.ar15.trigger_guard_rear_x}
Worked out 1.4985 in ± 0.005 in used
{std.ar15.trigger_guard_rear_x}, harvested
A mil-spec pattern: Primary Arms of this lower, "ready for any Mil-Spec upper" (the Mod 0 stock lower's page) and "Trigger Pin Diameter MIL-SPEC .154"; BCM, of its parts kit, "all MIL SPEC lower receivers built per the USGI TDP". The drawing's figure (8448608).
Photo 1.479 in ± 0.03 in
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1411, 777) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing
The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it.
Trigger guard rear ear hole, Y-2.18 in ± 0.005 in -55.4 mmConfirmedWorked out: {std.ar15.trigger_guard_rear_y}
Worked out -2.18 in ± 0.005 in used
{std.ar15.trigger_guard_rear_y}, harvested
A mil-spec pattern: Primary Arms of this lower, "ready for any Mil-Spec upper" (the Mod 0 stock lower's page) and "Trigger Pin Diameter MIL-SPEC .154"; BCM, of its parts kit, "all MIL SPEC lower receivers built per the USGI TDP". The drawing's figure (8448608).
Photo -2.181 in ± 0.03 in
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1411, 777) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing
The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it.
Trigger guard front ear hole, X3.342 in ± 0.005 in 84.9 mmConfirmedWorked out: {std.ar15.trigger_guard_front_x}
Worked out 3.3425 in ± 0.005 in used
{std.ar15.trigger_guard_front_x}, harvested
A mil-spec pattern: Primary Arms of this lower, "ready for any Mil-Spec upper" (the Mod 0 stock lower's page) and "Trigger Pin Diameter MIL-SPEC .154"; BCM, of its parts kit, "all MIL SPEC lower receivers built per the USGI TDP". The drawing's figure (8448608).
Photo 3.298 in ± 0.05 in
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1655, 778) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing
The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it.
Trigger guard front ear hole, Y-2.18 in ± 0.005 in -55.4 mmConfirmedWorked out: {std.ar15.trigger_guard_rear_y}
Worked out -2.18 in ± 0.005 in used
{std.ar15.trigger_guard_rear_y}, harvested
A mil-spec pattern: Primary Arms of this lower, "ready for any Mil-Spec upper" (the Mod 0 stock lower's page) and "Trigger Pin Diameter MIL-SPEC .154"; BCM, of its parts kit, "all MIL SPEC lower receivers built per the USGI TDP". The drawing's figure (8448608).
Photo -2.162 in ± 0.03 in
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1655, 778) on a gridded crop (scratch/crop.py), carried through that frame: the hole's end (a pin's end, the selector's end, the guard's roll pin, the guard's front hole) as its ring's centre; one of the frame's own points, so a check of the frame's fit, not of the drawing
The drawing's: the hole is one of the points the photo's frame was fitted to, and sits within its ± of it.
Rear face (the buffer tower's, where the end plate bears) behind the takedown pin1.125 in ± 0.005 in 28.6 mmConfirmedWorked out: -{std.ar15.receiver_rear_x}
Worked out 1.125 in ± 0.005 in used
-{std.ar15.receiver_rear_x}, harvested
A mil-spec pattern: Primary Arms of this lower, "ready for any Mil-Spec upper" (the Mod 0 stock lower's page) and "Trigger Pin Diameter MIL-SPEC .154"; BCM, of its parts kit, "all MIL SPEC lower receivers built per the USGI TDP". The drawing's figure (8448608). The right photo has BCM's QD end plate against it, its front face at 1.044 behind the pin: the plate's near face, standing out of the photo's frame plane, which the face's own figure doesn't rest on.
Top of the buffer-tower ring above the pin line1.573 in ± 0.0065 in 40 mmConflictWorked out: {std.ar15.buffer_tower_top_y}
Worked out 1.5735 in ± 0.0065 in used
{std.ar15.buffer_tower_top_y}, harvested
A mil-spec pattern: the ring's top is the drawing's (1.325 above the deck).
Photo 1.511 in ± 0.02 in
the no-stock complete lower's right side on white: Primary Arms' LRG-RMS-NO-STOCK_01 (2200 x 1467), harvested
Scale: frame from the reviewed holes takedown, pivot, selector, trigger, hammer, guard_rear, guard_front (134.1 px/in, rms 0.030 in over 7 points). Read by y_max of the traced outline (tools/trace.py)
The tower ring's top as its silhouette: the drawing's is 1.5735 (std.ar15.buffer_tower_top_y).
The drawing's: the photo's silhouette there is cut by the end plate taken out of the mask, and reads low by what a round ring falls in 0.2 in ahead of its crest.
std and right differ by 0.063 in beyond what each states it is good to.
The right photo's silhouette over the ring is 0.06 under the drawing's top: the ring is round and stands behind the end plate and castle nut there, which were taken out of the mask at the ring's rear (x -0.96), so the outline's highest point is the ring's shoulder ahead of its crest, not its top.
Deck (the receiver's top edge between the tower and the pivot lug) above the pin line0.246 in ± 0.022 in 6.2 mmProvisionalPhoto: the no-stock complete lower's right side on white: Primary Arms' LRG-RMS-NO-STOCK_01 (2200 x 1467)
Photo 0.246 in ± 0.022 in used
the no-stock complete lower's right side on white: Primary Arms' LRG-RMS-NO-STOCK_01 (2200 x 1467), harvested
Scale: frame from the reviewed holes takedown, pivot, selector, trigger, hammer, guard_rear, guard_front (134.1 px/in, rms 0.030 in over 7 points). Read by top (tooth tops: the edge's max over 0.05 in windows) along x [0.6, 5.8] of the traced outline (tools/trace.py)
The top edge between the tower and the pivot lug: the drawing's deck is 0.2485 (std.ar15.deck_y).
Front edge of the walls' sweep up to the tower ring, above the deck, X-0.439 in ± 0.02 in -11.2 mmProvisionalPhoto: the no-stock complete lower's right side on white: Primary Arms' LRG-RMS-NO-STOCK_01 (2200 x 1467)
Photo -0.439 in ± 0.02 in used
the no-stock complete lower's right side on white: Primary Arms' LRG-RMS-NO-STOCK_01 (2200 x 1467), harvested
Scale: frame from the reviewed holes takedown, pivot, selector, trigger, hammer, guard_rear, guard_front (134.1 px/in, rms 0.030 in over 7 points). Read by x_max in x [-1.5, 3.0] in y [0.5, 1.4] of the traced outline (tools/trace.py)
Front edge of the walls' sweep up to the ring, above the deck.
Front of the pivot-pin lug, X6.568 in ± 0.02 in 166.8 mmConflictPhoto: the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467
Photo 6.568 in ± 0.02 in used
the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in. Read by picked at px (95, 458) on a gridded crop (scratch/crop.py), carried through that frame: the lug's rounded front on the left side, where the pivot pin's flush end is its centre
Photo 6.626 in ± 0.035 in
the no-stock complete lower's right side on white: Primary Arms' LRG-RMS-NO-STOCK_01 (2200 x 1467), harvested
Scale: frame from the reviewed holes takedown, pivot, selector, trigger, hammer, guard_rear, guard_front (134.1 px/in, rms 0.030 in over 7 points). Read by x_max of the traced outline (tools/trace.py)
The right side's front is the pivot pin's domed head standing out of the right ear (0.43 in across on the photo), 0.06 ahead of the lug it covers.
The lug itself: on the left side the pin's end is flush and the lug's round front is the silhouette; on the right the pin's head stands over it and reaches further.
left and right differ by 0.058 in beyond what each states it is good to.
Front face of the magazine well, X6.091 in ± 0.033 in 154.7 mmProvisionalPhoto: the no-stock complete lower's right side on white: Primary Arms' LRG-RMS-NO-STOCK_01 (2200 x 1467)
Photo 6.091 in ± 0.033 in used
the no-stock complete lower's right side on white: Primary Arms' LRG-RMS-NO-STOCK_01 (2200 x 1467), harvested
Scale: frame from the reviewed holes takedown, pivot, selector, trigger, hammer, guard_rear, guard_front (134.1 px/in, rms 0.030 in over 7 points). Read by x_max in x [3.0, 7.0] in y [-1.5, -0.6] of the traced outline (tools/trace.py)
Front face of the magazine well (the near wall's).
Lowest point of the receiver below the pin line (the guard apart)2.298 in ± 0.02 in 58.4 mmProvisionalPhoto: the no-stock complete lower's right side on white: Primary Arms' LRG-RMS-NO-STOCK_01 (2200 x 1467)
Photo 2.298 in ± 0.02 in used
the no-stock complete lower's right side on white: Primary Arms' LRG-RMS-NO-STOCK_01 (2200 x 1467), harvested
Scale: frame from the reviewed holes takedown, pivot, selector, trigger, hammer, guard_rear, guard_front (134.1 px/in, rms 0.030 in over 7 points). Read by −y_min of the traced outline (tools/trace.py)
Lowest point of the receiver as traced (the guard and the rear ears are taken out): the front ears' foot at the well's rear.
The trigger guard's rear ears, their foot, Y-2.333 in ± 0.03 in -59.3 mmProvisionalPhoto: the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467
Photo -2.333 in ± 0.03 in used
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1385, 797) on a gridded crop (scratch/crop.py), carried through that frame: the ears' lower edge between the grip's front and the guard's rear end, where the ears show below the guard
The trigger guard's front ears, their foot at the well's rear, Y-2.288 in ± 0.03 in -58.1 mmProvisionalPhoto: the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467
Photo -2.288 in ± 0.03 in used
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1665, 795) on a gridded crop (scratch/crop.py), carried through that frame: the front ears' lower edge ahead of the guard's front hole
The trigger's opening between the ears, its rear at the seat's level, X1.68 in ± 0.03 in 42.7 mmProvisionalPhoto: the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467
Photo 1.68 in ± 0.03 in used
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1440, 634) on a gridded crop (scratch/crop.py), carried through that frame: where the rear ears' front edge meets the body's lower edge over the opening
The trigger's opening between the ears, its front at the seat's level, X2.947 in ± 0.03 in 74.9 mmProvisionalPhoto: the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467
Photo 2.947 in ± 0.03 in used
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1610, 635) on a gridded crop (scratch/crop.py), carried through that frame: where the front ears' rear edge meets the body's lower edge over the opening
Magazine well's outside walls, rear edge, X (right side)3.588 in ± 0.03 in 91.1 mmProvisionalPhoto: the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467
Photo 3.588 in ± 0.03 in used
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1695, 700) on a gridded crop (scratch/crop.py), carried through that frame: the upright edge where the well's wall begins, ahead of the fence and the front ears
Magazine well's outside walls, rear edge of their lower part, X (left side)3.435 in ± 0.03 in 87.2 mmProvisionalPhoto: the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467
Photo 3.435 in ± 0.03 in used
the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in. Read by picked at px (500, 640) on a gridded crop (scratch/crop.py), carried through that frame: the lower end of the left wall's S-curve, at the front ears
Magazine well's left wall, its upper part's rear edge, X3.03 in ± 0.03 in 77 mmProvisionalPhoto: the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467
Photo 3.03 in ± 0.03 in used
the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in. Read by picked at px (555, 560) on a gridded crop (scratch/crop.py), carried through that frame: the left wall's upright rear edge behind the bolt catch's bosses, from the deck down
Magazine well's left wall, where its rear edge begins to curve forward, Y-0.922 in ± 0.04 in -23.4 mmProvisionalPhoto: the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467
Photo -0.922 in ± 0.04 in used
the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in. Read by picked at px (555, 590) on a gridded crop (scratch/crop.py), carried through that frame: the top of the S-curve
Magazine well's left wall, where its rear edge's curve ends, Y-1.317 in ± 0.04 in -33.5 mmProvisionalPhoto: the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467
Photo -1.317 in ± 0.04 in used
the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in. Read by picked at px (500, 640) on a gridded crop (scratch/crop.py), carried through that frame: the foot of the S-curve
Bolt catch bosses, the rear one's rear edge, X3.091 in ± 0.03 in 78.5 mmProvisionalPhoto: the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467
Photo 3.091 in ± 0.03 in used
the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in. Read by picked at px (550, 488) on a gridded crop (scratch/crop.py), carried through that frame: the rear boss's rear edge on the left face
Bolt catch bosses, the front one's front edge, X3.617 in ± 0.03 in 91.9 mmProvisionalPhoto: the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467
Photo 3.617 in ± 0.03 in used
the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in. Read by picked at px (481, 488) on a gridded crop (scratch/crop.py), carried through that frame: the front boss's front edge on the left face
Bolt catch bosses, their lower ends, Y-0.154 in ± 0.03 in -3.9 mmProvisionalPhoto: the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467
Photo -0.154 in ± 0.03 in used
the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in. Read by picked at px (481 to 550, 488) on a gridded crop (scratch/crop.py), carried through that frame: the bosses' lower ends (each a rounded end)
Bolt catch bosses: the gap between them, rear edge, X3.203 in ± 0.007 in 81.4 mmConfirmedWorked out: {std.ar15.bolt_catch_slot_front_x} - {std.ar15.bolt_catch_slot_width}
Worked out 3.203 in ± 0.007 in used
{std.ar15.bolt_catch_slot_front_x} - {std.ar15.bolt_catch_slot_width}, harvested
The gap is the drawing's slot for the catch. The left photo's gap is 0.168 wide (the drawing's .172) from 3.259 to 3.427: 0.05 ahead of the drawing's, inside the frame's miss there.
Photo 3.259 in ± 0.06 in
the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in. Read by picked at px (528, 488) on a gridded crop (scratch/crop.py), carried through that frame: the rear boss's front edge
The drawing's slot; the photo's gap has its width and sits 0.056 ahead of it.
Bolt catch bosses: the gap's front edge, X3.375 in ± 0.005 in 85.7 mmConfirmedWorked out: {std.ar15.bolt_catch_slot_front_x}
Worked out 3.375 in ± 0.005 in used
{std.ar15.bolt_catch_slot_front_x}, harvested
The drawing's slot for the catch.
Photo 3.427 in ± 0.06 in
the same lower, LEFT side, square on white: Primary Arms LRG-RMS-NO-STOCK_03, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' flush ends and the trigger and hammer pins' ends (std.ar15.*): 131.1 px/in, turned 1.86 degrees; every one within 0.008 in. Read by picked at px (506, 488) on a gridded crop (scratch/crop.py), carried through that frame: the front boss's rear edge
As bolt_catch_gap_rear_x.
The magazine catch's fence on the right, rear edge, X2.864 in ± 0.03 in 72.7 mmProvisionalPhoto: the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467
Photo 2.864 in ± 0.03 in used
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1600, 560) on a gridded crop (scratch/crop.py), carried through that frame: the raised frame round the button's pocket, its rear edge
The magazine catch's fence, front edge, X3.61 in ± 0.03 in 91.7 mmProvisionalPhoto: the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467
Photo 3.61 in ± 0.03 in used
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1700, 560) on a gridded crop (scratch/crop.py), carried through that frame: the frame's front edge
The magazine catch's fence, its top (under the roll), Y-0.202 in ± 0.03 in -5.1 mmProvisionalPhoto: the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467
Photo -0.202 in ± 0.03 in used
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1650, 515) on a gridded crop (scratch/crop.py), carried through that frame: where the frame meets the roll's lower edge
The magazine catch's fence, its lower edge, Y-1.015 in ± 0.03 in -25.8 mmProvisionalPhoto: the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467
Photo -1.015 in ± 0.03 in used
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1650, 624) on a gridded crop (scratch/crop.py), carried through that frame: the frame's lower edge over the trigger's opening
The magazine catch's fence, its corners, radius0.06 in ± 0.03 in 1.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the frame's corners on the right photo are round, about this much; not read on a crop.
Worked out 0.06 in ± 0.03 in used
An assumption for the drawing, not a reading: the frame's corners on the right photo are round, about this much; not read on a crop., harvested
The roll along the top of the well's right wall, its lower edge, Y-0.202 in ± 0.03 in -5.1 mmProvisionalPhoto: the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467
Photo -0.202 in ± 0.03 in used
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1860, 518) on a gridded crop (scratch/crop.py), carried through that frame: the dark crease under the roll, level along the well
The roll along the top of the well's right wall, its rear end, X2.78 in ± 0.04 in 70.6 mmProvisionalPhoto: the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467
Photo 2.78 in ± 0.04 in used
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (1590, 470) on a gridded crop (scratch/crop.py), carried through that frame: where the roll's lit crest begins over the fence's rear
The roll's flat front end beside the pivot lug, X6.181 in ± 0.03 in 157 mmProvisionalPhoto: the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467
Photo 6.181 in ± 0.03 in used
the no-stock complete lower, RIGHT side, square on white: Primary Arms LRG-RMS-NO-STOCK_01, 2200 x 1467, harvested
Scale: a frame fitted by least squares to the takedown and pivot pins' heads and five of the Army drawing's holes (the selector's end, the trigger and hammer pins' ends, the guard's rear roll pin and front hole, at std.ar15.*): 134.1 px/in, turned 0.84 degrees; the worst miss 0.045 in (the guard's front hole), the pins' proud heads reading 0.035 further apart than the holes on the face. Read by picked at px (2046, 492) on a gridded crop (scratch/crop.py), carried through that frame: the roll's front end, beside the pivot pin's head
The roll along the top of the magazine well's right wall, its crest from the centre plane (Z)0.8 in ± 0.05 in 20.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file looks along the receiver: drawn as far out as the forged mil-spec roll the catalog has read through a camera (the Workhorse's 0.80, which Bear Creek's takes too). The right photo has this roll's lower edge at -0.202 and its front end at 6.181, where the Workhorse's are -0.204 and 6.231: one forging pattern.
Worked out 0.8 in ± 0.05 in used
An assumption for the drawing, not a reading: no view on file looks along the receiver: drawn as far out as the forged mil-spec roll the catalog has read through a camera (the Workhorse's 0.80, which Bear Creek's takes too). The right photo has this roll's lower edge at -0.202 and its front end at 6.181, where the Workhorse's are -0.204 and 6.231: one forging pattern., harvested
The roll's rear end, its rounding0.1 in ± 0.05 in 2.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the rear end is round on the right photo, over about this much; not read.
Worked out 0.1 in ± 0.05 in used
An assumption for the drawing, not a reading: the rear end is round on the right photo, over about this much; not read., harvested
The trigger guard, its width across (Z)0.442 in ± 0.05 in 11.2 mmProvisionalWorked out: An assumption for the drawing, not a reading: the guard is drawn as wide as the gap between the ears it is pinned in (std.ar15.trigger_guard_ear_gap, the drawing's .438 +.008; the script asserts it is no wider). BCM's photo of it installed, from below and ahead (c50cd1de432a), has its bar no wider than the ears; no view on file is square to it.
Worked out 0.442 in ± 0.05 in used
An assumption for the drawing, not a reading: the guard is drawn as wide as the gap between the ears it is pinned in (std.ar15.trigger_guard_ear_gap, the drawing's .438 +.008; the script asserts it is no wider). BCM's photo of it installed, from below and ahead (c50cd1de432a), has its bar no wider than the ears; no view on file is square to it., harvested
The trigger guard, its rear end inside the rear ears, X1.3 in ± 0.08 in 33 mmProvisionalWorked out: An assumption for the drawing, not a reading: hidden between the rear ears: the guard's end is drawn 0.2 in behind its roll pin, as far as the ears reach behind it on the right photo (their rear face at the grip's front, 1.29).
Worked out 1.3 in ± 0.08 in used
An assumption for the drawing, not a reading: hidden between the rear ears: the guard's end is drawn 0.2 in behind its roll pin, as far as the ears reach behind it on the right photo (their rear face at the grip's front, 1.29)., harvested
The trigger guard, its front end inside the front ears, X3.47 in ± 0.06 in 88.1 mmProvisionalWorked out: An assumption for the drawing, not a reading: hidden between the front ears: drawn to the well's rear wall (std.ar15.magwell_front_inner_x less std.ar15.magwell_length, 3.472), past its front hole.
Worked out 3.47 in ± 0.06 in used
An assumption for the drawing, not a reading: hidden between the front ears: drawn to the well's rear wall (std.ar15.magwell_front_inner_x less std.ar15.magwell_length, 3.472), past its front hole., harvested
The trigger guard's two ends between the ears, their top, Y-2.03 in ± 0.05 in -51.6 mmProvisionalWorked out: An assumption for the drawing, not a reading: hidden between the ears: drawn up to where the guard's upper edge goes behind them on the right photo (-2.09 at the rear, -2.03 at the front), level.
Worked out -2.03 in ± 0.05 in used
An assumption for the drawing, not a reading: hidden between the ears: drawn up to where the guard's upper edge goes behind them on the right photo (-2.09 at the rear, -2.03 at the front), level., harvested
The trigger guard's edges, their rounding0.03 in ± 0.02 in 0.8 mmProvisionalWorked out: An assumption for the drawing, not a reading: a moulded guard's edges are round (BCM: "No sharp edges, which increases comfort"); how round isn't read on any photo on file.
Worked out 0.03 in ± 0.02 in used
An assumption for the drawing, not a reading: a moulded guard's edges are round (BCM: "No sharp edges, which increases comfort"); how round isn't read on any photo on file., harvested
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
AR-15 receiver pins
- Uppers
- Aero Precision M4E1 Enhanced Upper Receiver Stripped, Aero Precision M4E1 Threaded upper receiver, BCM M4 Upper Receiver Assembly (w/ Laser T-Markings), Expo Arms 7075 Stripped AR-15 Upper Receiver, Geissele Automatics Super Duty Stripped Upper Receiver, Nordic Components 22RB .22 LR upper, 16", Palmetto State Armory AR-15 Stripped Upper Receiver, Panzer Arms AR57 ULT Complete AR-15 Upper Receiver - 5.7x28mm - 12", Panzer Arms AR57 Ultra Light Tactical Complete AR-15 Upper Receiver - 5.7x28mm - 16"
AR-15 receiver extension thread
- Folding stock adapters
- Law Tactical AR Folding Stock Adapter Gen 3-M, Law Tactical AR Folding Stock Adapter GEN-S, Sylvan Arms SA5 Pro AR15 Folding Stock Adapter (Opens To The Left), Sylvan Arms SA5 Pro AR15 Folding Stock Adapter (Opens To The Right)
- Receiver extensions
- BCM Milspec Carbine Receiver Extension (Buffer Tube) 6 Position, BCM MK2 Receiver Extension, Geissele Automatics Premium Mil-Spec Buffer Tube, Guntec USA AR-15 Mil-Spec Buffer Tube (Gen 2), SB Tactical SBPDW receiver extension, housing and integral castle nut, VLTOR RE-A5 7-Position Receiver Extension, MilSpec Diameter
AR-15 magazine well
AR-15 grip mount
AR-15 trigger guard ears
- Trigger guards
- Magpul MOE enhanced trigger guard, polymer
AR-15 fire-control group (mounting only)
AR-15 lower parts kit
- Lower parts kits
- CMMG Lower Parts Kit, AR15, Rise Armament Lower parts kit, less trigger
AR-15 safety selector
- Safety selectors
- CMMG Safety Selector, AR15, Radian Weapons Talon 45/90 - 2 Lever Kit