Trigger
LaRue Tactical MBT-2S trigger, straight

- Weight
- 2.9 oz Provisionalpublished: Rifle Configurator (aggregator; provenance unstated), a seller, read Sep 30, 2026
- Lowest price
- $100.99 at Impact Guns, read Nov 21, 2026
- Maker's number
- LT-MBT-2SSB
- Colour
- Black (placeholder)
- Drawn as
- modelled
In “22RB .22 LR rifle”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Trigger pin size0.154 in 3.9 mmConfirmedPublished: LaRue Tactical, the maker, read Sep 30, 2026
Published “Small Pin (.154")” used
LaRue Tactical, the maker, read Sep 30, 2026 the page, harvested Sep 30, 2026
Trigger face ahead of the trigger pin (at the exposed blade's mid-height)0.129 in ± 0.05 in 3.3 mmProvisionalPhoto: LaRue MBT-2S-SB, straight side view on white, marked LTMBT-2S-SB; supplied in chat
Photo 0.129 in ± 0.05 in used
LaRue MBT-2S-SB, straight side view on white, marked LTMBT-2S-SB; supplied in chat, from the site owner
Scale: the pivot hole, 46.8 px across (circle through the 50% edge; 46.2–48.0 px at the 65–35% levels) = the 0.154 in pin (larue-mbt-2s.pin_diameter); 303.8 px/in. The hole's running clearance is unsourced; each 0.001 in of it would enlarge the outline 0.65%. Read by front edge of the traced outline at the exposed blade's mid-height, 0.925 in below the pin (tools/trace.py target); ± mostly the rest-angle assumption (the photo's tail edge taken as installed-level; 3° of rotation moves the face ~0.05 in)
Re-derived 2026-09-30 by tools/trace.py: the prototype read the hole 2 px small (a 78%-white threshold), but the face sits almost under the pin, so the value is unchanged.
The finger contact point is taken as the blade's front face halfway down its exposed length (from the lower's underside, 0.451 in below the pin, to the tip, 1.46 in below). The SB blade's front face is straight.
Trigger face X (at the finger contact point)2.057 in ± 0.05 in 52.2 mmProvisionalWorked out: {bad-workhorse-lower.trigger_pin_x} + {.face_offset_x}
Worked out 2.057 in used
{bad-workhorse-lower.trigger_pin_x} + {.face_offset_x}, from the site owner
Length of pull is measured from here.
Blade width (Z)0.305 in ± 0.01 in 7.7 mmCorroboratedPublished: AR15.com, LaRue Tactical subforum, 'LaRue MBT-2S width?' (read through search results; the page returns 403), a review, read Oct 1, 2026
Published “the trigger face measures 0.305" wide side to side ... only 15 thousands of an inch wider than mil-spec ... flat with a small chamfer along the sides to break the edges” used
AR15.com, LaRue Tactical subforum, 'LaRue MBT-2S width?' (read through search results; the page returns 403), a review, read Oct 1, 2026 the page, harvested Oct 1, 2026
Photo 0.295 in ± 0.012 in
the user's own LTMBT-2S-SB standing on its tail on a counter, the bow's face toward the lens, a US quarter lying beside it; 2026-10-05, from the site owner
Scale: nothing of known size is in the bow's own plane (the quarter lies on the counter, an inch and more under the face). Two things bound it. Its pin bosses, in the same view and a tenth of an inch behind the face, are 237.9 px end to end to the bow's 105.0: 2.27 times it, and they go between the walls of a pocket .690 wide (std.ar15.fcg_pocket_width), so the bow is under 0.305; at the Army's own trigger's .680 it is 0.300. And seen along its height (bd521c1c8184) the trigger is 547.5 px long for the 1.899 in of its traced outline (profiles.side, which the pin's hole scales), its bow end-on 83.1 px: 0.288. Read by the bow's face from side to side, rows 1500 and 1560 (105.0 and 104.9 px), by the two bounds; ± covers both. As a check of where the lens was: at the quarter's own scale (324.6 px/in on the counter) the bow reads 0.3235, so the face is 7 to 9% nearer than the counter: an inch up, from 13 to 15 in
The user's own trigger, the straight bow. It cannot be the 0.305 of the thread and have its bosses in a standard pocket unless they fill it wall to wall; it agrees with the thread within the two figures' ±.
A caliper's figure against a photo's, which agrees with it within its ±: the user's own straight bow reads 0.295 ± 0.012. Which bow the thread measured still isn't on file; the photo says it can't have been much narrower than this one.
The face's width side to side. The thread (in AR15.com's LaRue Tactical industry subforum) answers its title question with a caliper figure; the page itself returns 403 to readers here, so the text is from search results (2026-10-01): the poster, the date and which bow (curved or the later straight) were measured aren't on file, and the ± covers the variant. A mil-spec bow measures 0.29 in (RECOIL's trigger guide: Stag's mil-spec 'measured 0.29 inches wide'; ALG QMS 'Bow Width: 0.29″'), which the thread's '15 thousands wider than mil-spec' matches. The face is flat with a small chamfer on its sides (the thread; Everyday Marksman: 'sharply-angled corners on the shoe'). Not the 0.25 in sometimes quoted for a mil-spec trigger: that's the body's thickness in the pocket.
Body thickness (Z), behind and above the bow0.3 in ± 0.012 in 7.6 mmProvisionalPhoto: the user's own LTMBT-2S-SB and its hammer on a counter, each seen along its own height, a US quarter lying between; 2026-10-05
Photo 0.3 in ± 0.012 in used
the user's own LTMBT-2S-SB and its hammer on a counter, each seen along its own height, a US quarter lying between; 2026-10-05, from the site owner
Scale: the trigger's own length in the same view, by its traced outline (profiles.side: 1.899 in from the tail's end to the nose's, 547.5 px, 288 px/in), and its pin bosses beside it (192.3 px: 0.438 of them, 0.298 at the Army's .680). The quarter is on the counter, under the trigger. Read by the body from side to side at row 1100 (columns 941.0 to 1025.2: 84.2 px): 0.292 by the outline's length, 0.298 by the bosses; 0.304 by the face-on view's bosses (3239ad914a00: 106.5 px of 237.9). ± covers the three and the outline's own scale (the pin's hole taken as the pin's size)
The trigger is one plate: its body is as thick as its bow is wide within 1.5% in both end-on photos (84.2 px to the bow's 83.1 seen along its height; 106.5 to 105.0 with the face toward the lens). A mil-spec trigger's body is 0.29 (std.ar15.trigger_body_width).
The bosses round the pin hole, end to end (across the trigger)0.68 in ± 0.012 in 17.3 mmProvisionalPhoto: the user's own LTMBT-2S-SB and its hammer on a counter, each seen along its own height, a US quarter lying between; 2026-10-05
Photo 0.68 in ± 0.012 in used
the user's own LTMBT-2S-SB and its hammer on a counter, each seen along its own height, a US quarter lying between; 2026-10-05, from the site owner
Scale: the trigger's own length in the same view, by its traced outline (profiles.side: 1.899 in, 547.5 px, 288 px/in); in the face-on view (3239ad914a00) the bow's own width (shoe_width). Read by the bosses' two ends at row 1285 (columns 886.8 to 1079.1: 192.3 px): 0.667 by the outline's length. Face on they are 237.9 px to the bow's 105.0: 0.691 at the thread's 0.305, 0.668 at the photo's 0.295. The middle; ± covers the three. A pocket is .690: they are not wider
What centres the trigger between the pocket's walls (std.ar15.fcg_pocket_width, .690): the Army's own trigger's are .680 ± .003 (bcm-pnt-trigger.boss_length, drawing 8448592). LaRue's reads the same within the photos.
The bosses round the pin hole, diameter0.285 in ± 0.02 in 7.2 mmProvisionalPhoto: LaRue MBT-2S-SB, straight side view on white, marked LTMBT-2S-SB; supplied in chat
Photo 0.285 in ± 0.02 in used
LaRue MBT-2S-SB, straight side view on white, marked LTMBT-2S-SB; supplied in chat, from the site owner
Scale: the pivot hole in the same face, 46.4 px along the row through its centre and 45.8 down the column (the 0.154 in pin, larue-mbt-2s.pin_diameter: 303.8 px/in, the trace's scale). Read by the dark ring round the hole, inside the spring's coil: 84 to 88 px across along the row through the hole's centre (columns 377.2 to 461.4 or 465.3), the coil's wire 115 px from centre to centre round it. ± is 6 px
Read inside the trigger spring's coil, which sits round the boss: the coil's wire and its shadow hide the boss's own edge by a few pixels either way. The Army's trigger's is .322 -.015 (std.ar15.trigger_boss_d).
The bow's face: the chamfer down each of its sides, across0.03 in ± 0.01 in 0.8 mmProvisionalPhoto: the user's own LTMBT-2S-SB held over a counter, the bow's face toward the lens; 2026-10-05
Photo 0.03 in ± 0.01 in used
the user's own LTMBT-2S-SB held over a counter, the bow's face toward the lens; 2026-10-05, from the site owner
Scale: the bow's own width in the same view and plane (shoe_width): 173 px from side to side at row 1700. Read by the dark band down each side of the lit face, rows 1700 and 1740: 15 to 20 px of the bow's 173 (the face itself 137 px): 0.027 to 0.035 in. ± is 5 px
The thread: 'flat with a small chamfer along the sides to break the edges'; Everyday Marksman: 'sharply-angled corners on the shoe'. Its angle isn't read (drawn at 45 degrees).
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
AR-15 fire-control group (mounting only)
- Lower receivers
- Aero Precision M4E1 complete lower, A2 grip and M4 stock, Aero Precision M4E1 Stripped Lower Receiver, Battle Arms Development Workhorse stripped lower, BCM MK2 AR-15 Lower Receiver, Bear Creek Arsenal BC-15 Multi Caliber, Lower Receiver, Black Anodized, Geissele Automatics Super Duty AR-15 Lower Receiver - Stripped Lower, Palmetto State Armory AR-15 "Stealth" Stripped Lower Receiver
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Impact Guns $100.99 Nov 21, 2026, in stock that day
- LaRue Tactical $139.99 Nov 21, 2026, out of stock that day