Grip
BCM Grip Mod 3
BCM's reduced-angle grip in its wider form ("Up to a quarter of an inch wider than the BCM® Mod 0 and Mod 1 grips"): a high beavertail, a tang that reaches forward under the trigger guard, and a hinged trap door over the hollow inside. Its straps lean 20 degrees installed, between the MOE-K2+'s 16 and the MOE+'s 26. On a lower with a trigger guard of its own the tang may be in the way.

- Weight
- 3.41 oz Conflictpublished: Dirty Bird Industries, BCMGUNFIGHTER Pistol Grip - MOD 3: Additional information (one page for four colours), a seller, read Oct 5, 2026Its sources span 3.15 oz to 3.65 oz.
- Lowest price
- $17.95 at Wing Tactical, read Nov 21, 2026 (Black)
- Maker's number
- BCM-GFG-Mod-3-BLK
- Colours
- Black, Flat Dark Earth, Foliage Green, Wolf Grey
- Drawn as
- modelled
- Maker's page
- bravocompanyusa.com
In “BCM 16 in mid-length”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Grip angle (the straps' lean from vertical, installed)19.6° ± 0.44°ConflictPhoto: BCM's Mod_3_FDE_3: the FDE grip lying on its right side on white with its screw, straight left side, 3700 x 2467
Photo 19.59 deg ± 0.44 deg used
BCM's Mod_3_FDE_3: the FDE grip lying on its right side on white with its screw, straight left side, 3700 x 2467, harvested
Scale: none needed: an angle within one outline. Read by the outline (luminance < 225) turned 15.33 degrees so that a line through its flat top (the top edge from 0.13 to 0.98 in ahead of the flat's rear end, 394 columns, rms 0.66 px) is level; then the mean lean of its edges in the band 0.45-0.85 of its height (rear 21.42, front 17.76: tools/trace.py edge_lean). ± is 1.5 px at each end of the fitted run.
Photo 20.02 deg ± 0.93 deg
BCM's Mod_3_FDE_4: the FDE grip cut out on white, straight right side, 1280 x 1280, harvested
Scale: none needed: an angle within one outline. Read by as flat-top-fde3 (turned 15.76 degrees; the flat top's line over 185 columns, rms 0.30 px; rear 21.83, front 18.20)
Photo 19.85 deg ± 0.78 deg
Primary Arms BCM-GFG-MOD-3-BLACK_00: the black grip on white, straight left side, 2200 x 1466, harvested
Scale: none needed: an angle within one outline. Read by as flat-top-fde3 (the photo has the flat top level already: turned 0.11 degrees; the line over 220 columns, rms 0.28 px; rear 21.62, front 18.09)
Photo 20.79 deg ± 0.78 deg
Primary Arms BCM-GFG-MOD-3-BLACK_01: the black grip on white, straight right side, 2200 x 1466, harvested
Scale: none needed: an angle within one outline. Read by as flat-top-fde3 (turned 1.12 degrees; the line over 220 columns, rms 0.43 px; rear 22.42, front 19.17)
Photo 20.2 deg ± 1.34 deg
Santomieri's BCM-Grip-Mod3-07: the black grip lying on white, straight left side, 1200 x 797, harvested
Scale: none needed: an angle within one outline. Read by as flat-top-fde3 (turned 13.54 degrees; the line over 128 columns, rms 0.27 px; rear 22.11, front 18.29)
Published “Grip Angle : ~17 degrees”
Rifle Configurator, "Best AR-15 Pistol Grips 2026" (a ranking with affiliate links; no method given), a review, read Oct 5, 2026 the page, harvested Oct 5, 2026
The only page that puts a number on it, and it says nothing of how (the same page files the grip under "17 degrees (modern default) ... Picks: Magpul K2+, K2, BCM Mod 3"). Kept in view, not used.
Installed, the flat top lies on the receiver's level underside, so the straps lean as they do from that face: an angle inside one outline, here the maker's own largest photo, which the side outline is traced from (so its flat top comes out level). Four other photos read the same within their ± (19.85 to 20.79). The ranking page's ~17 has no method behind it.
flat-top-fde3 and aggregator differ by 2.6° beyond what each states it is good to.
flat-top-fde4 and aggregator differ by 3° beyond what each states it is good to.
flat-top-pa-left and aggregator differ by 2.9° beyond what each states it is good to.
flat-top-pa-right and aggregator differ by 3.8° beyond what each states it is good to.
flat-top-review and aggregator differ by 3.2° beyond what each states it is good to.
The mean of the back and front straps' lean (the band 0.45 to 0.85 of the outline's height) with the flat top, which bears on the receiver's underside, level. BCM gives no figure: "Reduced angle for improved ergonomics and trigger control". Six side photos by three photographers, each turned until a line through its own flat top is level, read 19.6 to 20.8; the back strap leans about 21.6, the front strap 18.2.
"Overall Height" (the review's own measurement)4.242 in 107.7 mmProvisionalPublished: Josh Santomieri, "BCM Gunfighter Grip - Mod 3" (Santomieri Systems, 2014-05-06; the same text ran at The Truth About Guns): Specifications & Measurements, the BCM Mod 3 column, a review, read Oct 5, 2026
Published “Overall Height * 4.242 in (107.76 mm) [...] * - Overall height measured from where the grip meets the lower to the bottom of the grip.” used
Josh Santomieri, "BCM Gunfighter Grip - Mod 3" (Santomieri Systems, 2014-05-06; the same text ran at The Truth About Guns): Specifications & Measurements, the BCM Mod 3 column, a review, read Oct 5, 2026 the page, harvested Oct 5, 2026
Taken as the drop square to the flat top: from the face that bears on the receiver's underside to the grip's lowest point, its toe (a caliper's jaw laid on the flat top, the other on the toe). No photo of this grip on a lower with its pins in view has been read to check it (the one that was, Wing Tactical's for BCM's stock, turned out to show a Mod 0 grip). What holds it: at this scale the side outline is 1.905 in front to back where the same table says 1.918 (depth), and the Magpul MOE in the same table reads 4.069 in (103.36 mm), where Magpul's "Height, receiver to bottom" is 4.0 and Aero's photo of one installed 4.03 (magpul-moe-plus.bottom_below_lower_underside): his readings of this span run about 1% over.
Grip bottom below the receiver's underside where the grip bears4.242 in 107.7 mmConflictWorked out: {.review_height}
Worked out 4.242 in used
{.review_height}, harvested
The review's "Overall Height", taken as from the face the grip's flat top bears on to its lowest point (review_height says why).
Photo 4.145 in ± 0.07 in
Santomieri's BCM-Grip-Mod3-02: the Mod 3 and a Magpul MOE lying on their left sides, side by side, 1200 x 797, harvested
Scale: the MOE beside it, by Magpul's "Height, receiver to bottom 4.0 in." (magpul-moe-plus.bottom_below_lower_underside: the catalog's MOE+ side outline, the plain MOE's shape, fitted to its silhouette at 136.5 px per inch, rms 4.7 px). Read by this grip's traced side outline fitted to its silhouette in the same photo (rotation, translation and scale; the worst-fitting fifth of each silhouette, the open doors, left out): 133.3 px per inch of an outline drawn at 4.242, rms 1.9 px. The two scales are 0.9764 apart (0.9762 to 0.9784 at three thresholds): 4.242 x 0.9764. ± is the MOE's fit (a plain MOE against the MOE+'s outline) and Magpul's last digit.
The same reviewer's calipers have the two grips 4.242 and 4.069: 1.043 apart, where this photo has them 1.036 apart. So the photo bears out his ratio, and the 2% is his reading of the MOE over Magpul's own figure for it (4.069 against 4.0; Aero's photo of one installed, 4.03).
The one figure taken on this grip itself, with calipers. His photo of it beside a Magpul MOE has the two in the ratio his calipers give (1.036 against 1.043), so the question is what an MOE's own drop is: by Magpul's 4.0 this grip is 4.145, by his calipers' 4.069 it is 4.242. The model may be 2% large; that stays in view here until a Mod 3 is read on a lower with its pins in view.
review and lineup differ by 0.097 in beyond what each states it is good to.
What the side photo is scaled by: the grip frame's origin (the rear end of its flat top) down to its toe.
Front to back at the thickest portion of the hand grip, square to the straps (the review's "Width")1.918 in 48.7 mmCorroboratedPublished: Josh Santomieri, "BCM Gunfighter Grip - Mod 3" (Santomieri Systems, 2014-05-06; the same text ran at The Truth About Guns): Specifications & Measurements, the BCM Mod 3 column, a review, read Oct 5, 2026
Published “Width *** 1.918 in (48.71 mm) [...] *** - Width measured at the thickest portion of the actual hand grip area.” used
Josh Santomieri, "BCM Gunfighter Grip - Mod 3" (Santomieri Systems, 2014-05-06; the same text ran at The Truth About Guns): Specifications & Measurements, the BCM Mod 3 column, a review, read Oct 5, 2026 the page, harvested Oct 5, 2026
Photo 1.905 in ± 0.02 in
BCM's Mod_3_FDE_3: the FDE grip lying on its right side on white, straight left side, 3700 x 2467, harvested
Scale: the 4.242 in drop (bcm-grip-mod-3.bottom_below_lower_underside): 464.3 px/in. Read by the traced outline turned so the straps' mean lean is upright; its front-to-back width row by row: 2.08 at the foot's flare, 1.905 just above it (0.55 to 0.65 in above the base), narrowing to 1.65 under the tang. ± is the edges (1.5 px each) and where above the flare the widest row is taken.
The measured figure. The side outline, scaled by the same table's height, is 0.7% under it at the same place: the two figures hold together in one view. Nothing is drawn from this value.
Above the foot's flare: the foot itself is 2.1 to 2.3 in front to back. The Magpul MOE in the same table reads 1.979 in (50.27 mm).
Thickness (side to side)1.236 in 31.4 mmConflictPublished: Josh Santomieri, "BCM Gunfighter Grip - Mod 3" (Santomieri Systems, 2014-05-06; the same text ran at The Truth About Guns): Specifications & Measurements, the BCM Mod 3 column, a review, read Oct 5, 2026
Published “Thickness ** 1.236 in (31.39 mm) [...] ** - Thickness measured at the thickest portion of the grip.” used
Josh Santomieri, "BCM Gunfighter Grip - Mod 3" (Santomieri Systems, 2014-05-06; the same text ran at The Truth About Guns): Specifications & Measurements, the BCM Mod 3 column, a review, read Oct 5, 2026 the page, harvested Oct 5, 2026
The Magpul MOE in the same table reads 1.205 in (30.60 mm), where Magpul says "Thickness, max 1.2 in."
Published “Width : 1.4 inches (0.25" wider than Mod 0/1)”
Rifle Configurator, "Best AR-15 Pistol Grips 2026" (a ranking with affiliate links; no method given), a review, read Oct 5, 2026 the page, harvested Oct 5, 2026
No method, and it may be the foot's (foot_width).
A measured figure with its footnote, against a ranking page's round one. In the reviewer's own photo of the grip from behind, beside a Magpul MOE, the body is this wide where the MOE is Magpul's 1.2 (profiles.rear).
review and aggregator differ by 0.164 in beyond what each states it is good to.
The hand grip's, where the review's calipers took it. BCM: "Up to a quarter of an inch wider than the BCM® Mod 0 and Mod 1 grips."
Seat, X: where the grip's frame origin (its flat top's rear end) sits ahead of the takedown pin, installed-0.094 in ± 0.015 in -2.4 mmProvisionalWorked out: {std.ar15.receiver_rear_x} + {std.ar15.grip_lug_front_from_rear_face} - {.block_front_x}
Worked out -0.094 in used
{std.ar15.receiver_rear_x} + {std.ar15.grip_lug_front_from_rear_face} - {.block_front_x}, harvested
The block's front face (block_front_x, on the traced side) at the ears' rear face. If the ledge at the slot's mouth is what meets the ears, 0.017 further back.
A grip's own figure on the standard AR-15 grip mount. Seated by its interface: the top block's front face against the rear face of the trigger guard's ears, where the Army drawing ends the lug (2.300 from the receiver's rear face, 1.175 ahead of the takedown pin). That is how a BCM grip of this family sits in the one pin-framed photo on file (Wing Tactical's for the Mod 0 stock, a Mod 0 grip: its block's front face reads 1.176 ± 0.01 ahead of the pin, its top on the standard's seat at -1.065). The slot's rear wall then falls at the flat top's rear end, as the photos of the top show it, and the ledge at the slot's mouth is 0.93 below the top, the standard lug's depth. Until 01:45 on 2026-10-05 this was -0.019 ± 0.041, the outline fitted into that photo: a fit to another grip's straps.
Overall height in the grip frame (the beavertail's top to the toe)4.957 in ± 0.05 in 125.9 mmProvisionalPhoto: BCM's Mod_3_FDE_3: the FDE grip lying on its right side on white, straight left side, 3700 x 2467
Photo 4.957 in ± 0.05 in used
BCM's Mod_3_FDE_3: the FDE grip lying on its right side on white, straight left side, 3700 x 2467, harvested
Scale: scale from bcm-grip-mod-3.bottom_below_lower_underside = 4.242 in (y from the origin to the far edge 1970 px → 464.3 px/in). Read by height of the traced outline (tools/trace.py); the traced outline's height, the beavertail's top to the toe
Top block's front face, ahead of the flat top's rear end1.269 in ± 0.01 in 32.2 mmProvisionalPhoto: BCM's Mod_3_FDE_3: the FDE grip lying on its right side on white, straight left side, 3700 x 2467
Photo 1.269 in ± 0.01 in used
BCM's Mod_3_FDE_3: the FDE grip lying on its right side on white, straight left side, 3700 x 2467, harvested
Scale: scale from bcm-grip-mod-3.bottom_below_lower_underside = 4.242 in (y from the origin to the far edge 1970 px → 464.3 px/in). Read by x_max in y [-0.85, -0.25] of the traced outline (tools/trace.py); the top block's front face ahead of the flat top's rear end, between the corner above it and the ledge at the slot's mouth below (which stands 0.017 further out, 0.93 below the top)
Toe (the grip's lowest point), Y in the grip frame-4.242 in -107.7 mmProvisionalWorked out: -{.bottom_below_lower_underside}
Worked out -4.242 in used
-{.bottom_below_lower_underside}, harvested
Top block (the two walls that sit under the receiver), across0.88 in ± 0.04 in 22.4 mmProvisionalPhoto: BCM's BCM-GFG-Mod-3-BLK-5: a BCM lower with the grip, from ahead and the left, 1200 x 800
Photo 0.88 in ± 0.04 in used
BCM's BCM-GFG-Mod-3-BLK-5: a BCM lower with the grip, from ahead and the left, 1200 x 800, harvested
Scale: the receiver's own width where the grip meets it: the standard's 0.88 in body (std.ar15.lower_body_width). Read by the block's side face runs on into the receiver's with no step at the seam, on the side the photo shows: taken as the receiver's width. ± is a step of 0.02 in a side, which wouldn't show at this size.
No page gives it and no photo is square to it. The army's A2 grip is .885 across its top (aero-m4e1-lower.grip_body_width, drawing 9349127). The beavertail's neck reads this wide in the review's view from behind (profiles.rear).
Foot (the flare at the base), across: the widest the grip is, side to side1.36 in ± 0.05 in 34.5 mmProvisionalPhoto: Santomieri's BCM-Grip-Mod3-03: the Mod 3 lying on its front strap, its back strap straight on from above, a Magpul MOE beside it, 1200 x 797
Photo 1.36 in ± 0.05 in used
Santomieri's BCM-Grip-Mod3-03: the Mod 3 lying on its front strap, its back strap straight on from above, a Magpul MOE beside it, 1200 x 797, harvested
Scale: scale from bcm-grip-mod-3.thickness = 1.236 in (median width over 0.34–0.46 of the height from the top, 149–151 px 150 px → 121.4 px/in). Read by width of the traced outline (tools/trace.py); the outline's widest row, at the foot, at the scale the review's 1.236 in gives the upper body (rows 225 to 297, 149 to 151 px): at that scale the Magpul MOE lying beside it (its body 145 px across at the same threshold, 143 to 146) is 1.195 in, Magpul's 1.2. ± is the lens: the photo is taken from close, and what stands higher over the table reads larger
From the one view from behind, a close photo: read as photographed. A ranking page's "Width : 1.4 inches" (thickness, aggregator) may be this.
Front strap's ribs: how far back from the strap's edge they run, in the side view0.138 in ± 0.015 in 3.5 mmProvisionalPhoto: BCM's Mod_3_FDE_3: the FDE grip lying on its right side on white, straight left side, 3700 x 2467
Photo 0.138 in ± 0.015 in used
BCM's Mod_3_FDE_3: the FDE grip lying on its right side on white, straight left side, 3700 x 2467, harvested
Scale: the 4.242 in drop (bcm-grip-mod-3.bottom_below_lower_underside): 464.3 px/in. Read by read on a gridded 4x crop at rows 1250 to 1500, where the front strap stands 2.4 degrees off the photo's vertical: the ribs' crests at column 1359, their rear ends at 1420 to 1426: 64 px. ± is 6 px.
The ribs are about 0.047 in apart (22 px) and stand 0.012 in out of the strap's edge. Behind their ends a smooth band runs to the texture panel's front border, 0.224 in (104 px) behind the edge.
The slot in the top that goes over the receiver's lug, across0.385 in ± 0.01 in 9.8 mmCorroborated2 readings
Photo 0.374 in ± 0.02 in
Primary Arms BCM-GFG-MOD-3-BLACK_02: the black grip from ahead and the right, 2200 x 1466, harvested
Scale: the block's own width across the same face (bcm-grip-mod-3.top_block_width, 0.88 ± 0.04). Read by on 11 rows across the block's front face (rows 400 to 500, a 5-row mean each): the face's far edge (the silhouette), the slot's two walls (half-way between the lit face and the slot's dark) and the near corner (the chamfer's bright line). The slot is 45.5 px of 106.8: 0.4249 of the face (0.4223 to 0.4290 over the rows). ± is the block's width and 2 px on the corner.
Photo 0.373 in ± 0.02 in
Primary Arms BCM-GFG-MOD-3-BLACK_03: the black grip from ahead and the left, 2200 x 1467, harvested
Scale: the block's own width across the same face (bcm-grip-mod-3.top_block_width, 0.88 ± 0.04). Read by as pa-right, from the other side (the near corner is the chamfer's dark line here): the slot is 57.3 px of 135.3, 0.4239 of the face (0.4111 to 0.4354: it reads 3 px wider on the lower rows than the upper).
The slot goes over the receiver's lug, so it isn't under the lug's .375; the two readings, 0.374 and 0.373 ± 0.02, put it at 0.394 at most. The middle of what both leave, ± half of it: 0.005 in clear of the lug on each side, where the MOE-K2+'s slot is 0.025 clear. Stands until a view square to the top, with a scale, is read.
No view on file is square to the grip's top (the two from above, Wing Tactical's, are close and oblique, and the top face's edges can't be told apart in them). The slot is cut through the block's front face, and two photos see that face, one from each side: its two walls and the face's two outer corners are four lines in one plane, so their spacing along a row needs no scale. The slot is 0.4249 and 0.4239 of the face: at the block's 0.88 in, the lug's own .375 (std.ar15.grip_lug_width). A fit as tight as these photos can tell; the review: "These grips are often a tight fit on the lower, so you may have to give it a good push to get it on to the lower".
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
AR-15 grip mount
- Lower receivers
- Aero Precision M4E1 complete lower, A2 grip and M4 stock, Aero Precision M4E1 Stripped Lower Receiver, Battle Arms Development Workhorse stripped lower, BCM MK2 AR-15 Lower Receiver, Bear Creek Arsenal BC-15 Multi Caliber, Lower Receiver, Black Anodized, Geissele Automatics Super Duty AR-15 Lower Receiver - Stripped Lower, Palmetto State Armory AR-15 "Stealth" Stripped Lower Receiver
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Wing Tactical $17.95 Black Nov 21, 2026, in stock that day
- KYGUNCO $17.95 Black Nov 21, 2026, in stock that day
- BCM $19.95 Black Nov 21, 2026, in stock that day
- BCM $19.95 Flat Dark Earth Nov 21, 2026, in stock that day
- Primary Arms $19.95 Black Nov 21, 2026, in stock that day
- Dirty Bird Industries $19.95 Black Nov 21, 2026, in stock that day
- Dirty Bird Industries $19.95 Flat Dark Earth Nov 21, 2026, in stock that day
- AR15Discounts $19.95 Black Nov 21, 2026, stock not said
- AR15Discounts $19.95 Flat Dark Earth Nov 21, 2026, stock not said
- AR15Discounts $19.95 Foliage Green Nov 21, 2026, stock not said
- AR15Discounts $19.95 Wolf Grey Nov 21, 2026, stock not said
- MidwayUSA $19.95 Black Nov 21, 2026, in stock that day
- Alexander's Store $19.99 Black Oct 27, 2026, in stock that day
- Right To Bear $20.00 Black Nov 21, 2026, in stock that day
- T.REX ARMS $20.00 Black Nov 21, 2026, in stock that day
- T.REX ARMS $20.00 Flat Dark Earth Nov 21, 2026, in stock that day
- Dirty Bird Industries $19.95 Foliage Green Nov 21, 2026, out of stock that day
- Dirty Bird Industries $19.95 Wolf Grey Nov 21, 2026, out of stock that day
- Sportsman's Warehouse $19.99 Black Nov 21, 2026, out of stock that day
- Rifle Supply $23.99 Black Nov 21, 2026, out of stock that day