Receiver extension
BCM Milspec Carbine Receiver Extension (Buffer Tube) 6 Position
BCM's carbine receiver extension, the buffer tube, with six stock positions: "machined from 7075T6 and manufactured to Mil-Spec dimensions and specifications", "Hard Coat Anodized per Mil-A-8625F, Type III, Class 2". The stock rides on it, and the buffer and the action spring are inside it. BCM: "Mil-Spec receiver extensions have a slightly smaller dimension where the stock slides on."

- Weight
- 3.76 oz ± 0.2 oz Provisionalworked out: (0.785398163 * ({.tube_od} * {.tube_od} - {std.receiver_extension.bore_d} * {std.receiver_extension.bore_d}) * {.tube_length} + 0.785398163 * {std.receiver_extension.bore_d} * {std.receiver_extension.bore_d} * {std.receiver_extension.carbine_rear_wall} + {std.receiver_extension.rail_width} * ({std.receiver_extension.rail_bottom_below_axis} - {.tube_od} / 2) * ({.tube_length} - {std.receiver_extension.rail_ramp_end}) - 6 * 0.785398163 * {.position_hole_d} * {.position_hole_d} * ({std.receiver_extension.rail_bottom_below_axis} - {.tube_od} / 2)) * {std.density.aluminium_7075}
- Lowest price
- $38.95 at BCM, read Nov 21, 2026
- Maker's number
- BCM-Milspec-RE
- Colour
- Black (placeholder)
- Drawn as
- modelled
- Maker's page
- bravocompanyusa.com
In “22RB .22 LR rifle”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Receiver extension OD1.148 in 29.2 mmConflictWorked out: {std.receiver_extension.milspec_od}
Worked out 1.148 in used
{std.receiver_extension.milspec_od}, from the project brief
The kit is listed as a mil-spec tube, so the standard applies.
Photo 1.133 in
not yet archived, from the project brief
Scale: not recorded in brief. Read by exposed tube measured in the calibrated photo
1.3% below the standard, which points to photo scale error at the tube.
Mil-spec standard. The photo reading doubles as a check on that photo's calibration. Caliper to confirm.
std and moe-sl-photo differ by 0.015 in beyond what each states it is good to.
Receiver extension's front face behind the takedown pin (how far it screws in)0.669 in ± 0.02 in 17 mmConfirmedWorked out: -{std.receiver_extension.front_face_x}
Worked out 0.669 in ± 0.02 in used
-{std.receiver_extension.front_face_x}, from the site owner
The Army's drawings: screwed in until its edge stands over the buffer retainer's shoulder.
Photo 0.6 in ± 0.09 in
Magpul: an M4 with the MOE Carbine stock two steps out, right side, close, 1200 px, harvested
Scale: the stock's own length, 641.4 px for Magpul's 7.0 in: 91.6 px/in. Read by the stock's lock pin (its shaft over columns 530 to 553) is 500.5 px behind the takedown pin's head (1042, between its two highlights): 5.46 in, less up to 0.07 for the head standing nearer the lens than the tube: 5.43. Two steps out, the pin is in the third hole from the front, which this tube has 4.83 in behind its front face (tube_length − position_hole_rear_from_rear − 3 × position_step)
Another maker's tube on Magpul's rifle; ± adds the hole's place and the tube's generic length.
From the drawings of the parts that set it; the photo of a rifle agrees within its ±.
M5 drew the tube from the takedown pin's X, an assumption the app listed. It is hidden inside the receiver; what it moves is the tube's rear end, its rail's ramp and its six holes, 0.67 in back.
Receiver extension length7.25 in 184.1 mmCorroboratedPublished: Dirty Bird (One Horse mil-spec carbine tube, not BCM), a seller, read Sep 30, 2026
Published “7.25 inches (Carbine Length)” used
Dirty Bird (One Horse mil-spec carbine tube, not BCM), a seller, read Sep 30, 2026 the page, harvested Sep 30, 2026
Generic mil-spec carbine figure. BCM publishes none.
Published “Approx. 7.25 inches”
Mounts Plus (generic mil-spec article), a review, read Sep 30, 2026 the page, harvested Sep 30, 2026
Two generic sources agree; not BCM-specific, so it stays provisional.
Receiver extension position holes, diameter (in the rail)0.42 in ± 0.03 in 10.7 mmProvisionalPhoto: BCM mil-spec carbine receiver extension, underside, 1280 px
Photo 0.42 in ± 0.03 in used
BCM mil-spec carbine receiver extension, underside, 1280 px, harvested
Scale: the tube's 7.25 in (tube_length) = 1166 px (160.8 px/in); the rail is nearer the lens, so its features read ~2% large. Read by the rear hole's outline on a 4x crop, 69 px across
Blind, from the rail up to the tube's wall (Magpul's identification card: about 0.30 deep, which is the rail's depth below the tube).
Receiver extension position holes, spacing (what a stock moves per position)0.66 in 16.8 mmConfirmedWorked out: {magpul-moe-sl-carbine.position_step}
Worked out 0.66 in used
{magpul-moe-sl-carbine.position_step}, from the project brief
Magpul's MOE SL travel over a mil-spec carbine tube's six positions.
A property of the tube: any stock on it moves by this. BCM publishes no figure. Magpul states its stocks' travel on a mil-spec carbine tube (3.3 in over six positions); the six holes in BCM's underside photo read 0.68 apart at the silhouette's scale, the rail being nearer the lens (about 2% large), which agrees.
Receiver extension rear position hole, centre ahead of the tube's rear face0.44 in ± 0.03 in 11.2 mmProvisionalPhoto: BCM mil-spec carbine receiver extension, underside, 1280 px
Photo 0.44 in ± 0.03 in used
BCM mil-spec carbine receiver extension, underside, 1280 px, harvested
Scale: the tube's 7.25 in (tube_length) = 1166 px (160.8 px/in), corrected ~2% for the rail's nearness. Read by the rear hole's centre (px 1135.5, from its outline on a 4x crop) to the rear face (px 1209): 73.5 px
Six holes at the tube's position step (position_step).
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
AR-15 receiver extension thread
- Lower receivers
- Aero Precision M4E1 complete lower, A2 grip and M4 stock, Aero Precision M4E1 Stripped Lower Receiver, Battle Arms Development Workhorse stripped lower, BCM MK2 AR-15 Lower Receiver, Bear Creek Arsenal BC-15 Multi Caliber, Lower Receiver, Black Anodized, Geissele Automatics Super Duty AR-15 Lower Receiver - Stripped Lower, Palmetto State Armory AR-15 "Stealth" Stripped Lower Receiver
- Folding stock adapters
- Law Tactical AR Folding Stock Adapter Gen 3-M, Law Tactical AR Folding Stock Adapter GEN-S, Sylvan Arms SA5 Pro AR15 Folding Stock Adapter (Opens To The Left), Sylvan Arms SA5 Pro AR15 Folding Stock Adapter (Opens To The Right)
Receiver extension (buffer tube)
- Stocks
- B5 Systems Bravo Stock, B5 Systems Enhanced SOPMOD Stock, BCM Stock - Mod 0, Magpul CTR carbine stock, mil-spec, Magpul MOE carbine stock, mil-spec, Magpul MOE SL carbine stock, mil-spec, Mission First Tactical BATTLELINK Minimalist Milspec Stock
- Braces
- SB Tactical SBA3® AR Adjustable Pistol Stabilizing Brace®, SB Tactical SBA4® AR Adjustable Pistol Stabilizing Brace®, SB Tactical SBA5® AR Adjustable Pistol Stabilizing Brace®
Receiver extension end
Receiver extension bore
- Buffers
- Armaspec Stealth™ Recoil Spring - SRS™- AR15 GEN4, C (3.3 oz), Armaspec Stealth™ Recoil Spring - SRS™- AR15 GEN4, H (3.8 oz), Armaspec Stealth™ Recoil Spring - SRS™- AR15 GEN4, H2 (4.7 oz), Armaspec Stealth™ Recoil Spring - SRS™- AR15 GEN4, H3 (5.6 oz), BCM Carbine Buffer, BCM H Carbine Buffer, BCM H2 Carbine Buffer, BCM H3 Carbine Buffer, BCM MK2 Buffer Mod 1 - T0, Geissele Automatics Super 42 Braided Wire Buffer Spring and Buffer Combo, H1, Geissele Automatics Super 42 Braided Wire Buffer Spring and Buffer Combo, H2, Geissele Automatics Super 42 Braided Wire Buffer Spring and Buffer Combo, H3, Guntec USA AR-15 Mil-Spec Car Buffer, Guntec USA AR-15 Stainless Steel Car Buffer, JP Enterprises Silent Captured Spring AR-15 Heavy H2 GEN 2, JP Enterprises Silent Captured Spring AR-15 Heavy H3 GEN 2, JP Enterprises Silent Captured Spring AR-15 Standard GEN 2, KynSHOT RB5000, KynSHOT RB5000HP (High Performance), Panzer Arms AR57 proprietary carbine buffer, VLTOR A5H2 Buffer, 5.3 oz.
- Buffer springs
- BCM Carbine Action Spring, BCM Rifle M16 Action Spring, Guntec USA Upgraded Chrome Silicon Spring, VLTOR A5 Action Spring
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- BCM $38.95 Nov 21, 2026, in stock that day