Buffer
VLTOR A5H2 Buffer, 5.3 oz.
The A5 system's standard buffer, longer than a carbine buffer and only for VLTOR's A5 receiver extension. VLTOR: "The default A5 Buffer at 5.3 oz and the recommended starting point for most standard builds." "Internal Weights 2 Steel, 2 Tungsten", "Design Cascading Deadblow"; on the A5 page "Material Aluminum". "NOTE: A5 buffers are only compatible with other VLTOR A5 buffer system components. The buffers themselves are longer than traditional carbine buffers, and they cannot be used in standard carbine receiver extensions. The A5 Buffer is not compatible with the AR-10 Platform." Its head is marked "A5-2 VLTOR US. PAT. 8296984".

- Weight
- 5.3 oz Confirmedpublished: VLTOR, A5H2 Buffer, 5.3 oz. (SKU A5H2), SPECIFICATIONS, the maker, read Oct 28, 2026
- Lowest price
- $95.95 at VLTOR, read Nov 21, 2026
- Maker's number
- A5H2
- Colour
- VLTOR A5 buffer, bronze anodize
- Drawn as
- modelled
- Maker's page
- vltor.com
In “Two-tone 16 in, Stealth Gray and soft-shooting”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Length (the head's front face to the bumper's end)3.7 in ± 0.08 in 94 mmConflictPhoto: VLTOR's picture of its SP-A5 kit: the A5H2 standing, its head down, 1024 x 683) and ba600a518974 (its A5 Buffer Kit picture: the same picture of the buffer, 60 px across its body in both
Photo 3.7 in ± 0.08 in used
VLTOR's picture of its SP-A5 kit: the A5H2 standing, its head down, 1024 x 683) and ba600a518974 (its A5 Buffer Kit picture: the same picture of the buffer, 60 px across its body in both, harvested
Scale: the buffer's own three diameters, the standard's (std.carbine_buffer.head_d 0.98, pilot_d 0.781, body_d 0.687): 86 to 87, 69 and 60 px, in the standard's ratios (0.80 and 0.70 of the head, against 0.797 and 0.701). Read by its length from the bumper's end (253 px) to the head's front face (580 px), 327 px: 3.68 in by the head, 3.70 by the step, 3.74 by the body. The picture looks a little down on it (the bumper's end shows as an ellipse about a fifth as tall as it is wide: 12°), which shortens it 2%; the ± covers that and the edges. On the kit picture beside the tube (ba600a518974) it is at the tube's own scale within 2 to 3.5% (90.5 px/in by the tube's 7 15/16), and reads 3.61 there.
Worked out “Buffer Length Short (3.25") 3/4" longer — more mass distribution”
3.25in + 0.75in, harvested
https://vltor.com/a5, retrieved 2026-10-28.
VLTOR's photograph of the buffer, read by its own diameters in the standard's proportions, which three of them keep to 1.5%. The table's "3/4" longer" is a round comparison in a table whose other rows are loose (it gives a carbine tube "4 positions", where a carbine tube has six), and taken as a length it contradicts VLTOR's own sentence beside it, "The receiver extension is longer to allow more bolt carrier travel": in the RE-A5 as drawn (its front face, length and the carbine tube's rear wall) a 4.0 in buffer leaves the carrier 0.06 in less travel than a carbine buffer has in a carbine tube, and the 3.7 of the photograph 0.24 more. Kept beside it.
photo and vltor-table differ by 0.3 in beyond what each states it is good to.
No page states it. VLTOR's A5 page, of the buffer: "A5 buffers ... The buffers themselves are longer than traditional carbine buffers, and they cannot be used in standard carbine receiver extensions" (https://vltor.com/products/a5h2); "If you put an A5 buffer in a carbine tube, the buffer is too long — it will prevent the carrier from cycling fully"; "The receiver extension is longer to allow more bolt carrier travel. The buffer is longer to house an additional tungsten weight." (https://vltor.com/a5).
Diameter (its head, which runs in the extension's bore)0.98 in ± 0.005 in 24.9 mmConfirmedWorked out: {std.carbine_buffer.head_d}
Worked out 0.98 in ± 0.005 in used
{std.carbine_buffer.head_d}, harvested
The standard carbine buffer's head: VLTOR's picture of the A5H2 (2531fc1da290) has its head, the step behind it and its body in the standard's proportions (86 to 87, 69 and 60 px for 0.98, 0.781 and 0.687).
It runs in the RE-A5's bore, the mil-spec 1.000 (std.receiver_extension.bore_d; VLTOR: "MilSpec Diameter" for the tube).
The body's length (the head's front face to the body's open end, where the bumper comes out)3.3 in ± 0.09 in 83.8 mmProvisionalWorked out: {.length} - {std.carbine_buffer.bumper_exposed}
Worked out 3.3 in ± 0.09 in used
{.length} - {std.carbine_buffer.bumper_exposed}, harvested
Its length less the standard bumper standing out of it: VLTOR's picture has the bumper 34 px of the 327 (0.38 to 0.40 in by the buffer's diameters), the standard's 0.40.
The pin through the body and the bumper, from the body's open end0.19 in ± 0.04 in 4.8 mmConflictPhoto: VLTOR's picture of the SP-A5 kit, the A5H2 standing, its head down
Photo 0.19 in ± 0.04 in used
VLTOR's picture of the SP-A5 kit, the A5H2 standing, its head down, harvested
Scale: the buffer's head, the standard's 0.98 in (od): 86.5 px. Read by the pin's middle at 303 px against the body's open end, where the bumper comes out, at 287 px on a crop at three times: 16 px
Worked out 0.24 in ± 0.005 in
{std.carbine_buffer.pin_from_open_end}, harvested
The Army's drawing of the rifle buffer's body.
VLTOR's own buffer; the standard's place is 0.05 further in, at the photo's ± from it.
photo and std differ by 0.05 in beyond what each states it is good to.
The pin shows in VLTOR's pictures as a small round head in a hole near the bumper (2531fc1da290, ba600a518974).
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Receiver extension bore
- Receiver extensions
- BCM Milspec Carbine Receiver Extension (Buffer Tube) 6 Position, BCM MK2 Receiver Extension, Geissele Automatics Premium Mil-Spec Buffer Tube, Guntec USA AR-15 Mil-Spec Buffer Tube (Gen 2), SB Tactical SBPDW receiver extension, housing and integral castle nut, VLTOR RE-A5 7-Position Receiver Extension, MilSpec Diameter
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- VLTOR $95.95 Nov 21, 2026, in stock that day