Receiver extension
SB Tactical SBPDW receiver extension, housing and integral castle nut
The SBPDW's own aluminium buffer tube with its castle nut made on it, and the housing it carries at the receiver, where an end plate would be; the brace's two rods run through the housing under the tube, and its levers release them. The maker: "Tighten the tube via the integral castle nut using a castle nut wrench. Be aware that the castle nut and receiver extension are aluminum, care must be taken when using a castle nut wrench." AR15Discounts: "The end plate and castle nut are integral to the assembly". It takes the rifle's own carbine buffer and spring ("SBPDW is compatible with mil-spec receivers and carbine length buffers and springs"). Sold only with the brace, as the SBPDW (PDW-01-SB).

- Weight
- 8.25 oz ± 0.9 oz Provisionalworked out: (0.785398163 * ({.tube_od} * {.tube_od} - {.bore_d} * {.bore_d}) * ({.tube_length} - {std.receiver_extension.thread_length}) + 0.785398163 * ({std.receiver_extension.thread_minor_d} * {std.receiver_extension.thread_minor_d} - {.bore_d} * {.bore_d}) * {std.receiver_extension.thread_length} + 0.785398163 * {.bore_d} * {.bore_d} * {.rear_wall} + 0.785398163 * ({.nut_od} * {.nut_od} - {.tube_od} * {.tube_od}) * {.nut_length} - {.nut_notch_count} * {.nut_notch_width} * {.nut_notch_depth} * ({.nut_od} - {.tube_od}) / 2 + ({sb-tactical-sbpdw-brace.rod_spacing} + {sb-tactical-sbpdw-brace.rod_d} + 2 * {.ear_wall}) * {.housing_bottom_below_axis} * {.housing_length} - 0.392699082 * {.housing_bore} * {.housing_bore} * {.housing_length} + 0.392699082 * ({.housing_od} * {.housing_od} - {.housing_bore} * {.housing_bore}) * {.housing_length} - 2 * 0.785398163 * {.rod_bore_d} * {.rod_bore_d} * {.housing_length}) * {std.density.aluminium}
- Lowest price
- Sold in the SB Tactical SBPDW®, not by itself
- Colour
- Black (placeholder)
- Drawn as
- modelled
- Maker's page
- sb-tactical.com
In “22RB .22 LR rifle”, a build on the start page, in place of its BCM Milspec Carbine Receiver Extension (Buffer Tube) 6 Position. No build on the start page takes it without a finding: the designer says what.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
The tube's front face behind the takedown pin (how far it screws in)0.669 in ± 0.02 in 17 mmConfirmedWorked out: -{std.receiver_extension.front_face_x}
Worked out 0.669 in ± 0.02 in used
-{std.receiver_extension.front_face_x}, harvested
The Army's drawings: screwed in until its edge stands over the buffer retainer's shoulder. The maker: "Depress the buffer retainer pin and continue threading the tube until the buffer retainer pin is captured."
Photo 0.682 in ± 0.02 in
SB Tactical sbpdw-side-product_image.jpg, the assembly alone from the right, harvested
Scale: 169.2 px/in (see the file's header). Read by the thread's front end (column 1631) 75 px ahead of the housing's front face (column 1556), which bears on the receiver's rear face 1.125 in behind the pin
The drawing that sets it; the maker's photo agrees within its ±.
The tube's outside diameter (behind the castle nut)1.141 in ± 0.02 in 29 mmProvisionalPhoto: the assembly alone from the right
Photo 1.141 in ± 0.02 in used
the assembly alone from the right, harvested
Scale: 169.2 px/in. Read by the tube's top edge between the nut and the brace (row 406, columns 880 to 1080) 96.5 px over the axis; its lower edge is behind the rods
No page states it. Read on the side photo; it slides in the brace's body, so its brace's bore is drawn over it (sb-tactical-sbpdw-brace.bore_d).
The tube's bore1 in ± 0.005 in 25.4 mmConfirmedWorked out: {std.receiver_extension.bore_d}
Worked out 1 in ± 0.005 in used
{std.receiver_extension.bore_d}, harvested
The Army's drawing's bore, what a buffer runs in; the maker: "SBPDW is compatible with mil-spec receivers and carbine length buffers and springs". No page gives this tube's own.
The tube's depth (its bore, from its front face to its rear wall)6.92 in ± 0.0005 in 175.8 mmProvisionalPublished: AR15Discounts, SB Tactical SBPDW Pistol Stabilizing Brace - AR - Black (PDW-01-SB), a seller, read Oct 18, 2026
Published “Depth of the tube is 6.920″” used
AR15Discounts, SB Tactical SBPDW Pistol Stabilizing Brace - AR - Black (PDW-01-SB), a seller, read Oct 18, 2026 the page, harvested Oct 18, 2026
One seller's figure, taken as the bore's depth from the tube's front face: what a buffer and its spring have. BCM's carbine tube as the catalog draws it has 7.18 in.
The tube's rear wall0.072 in ± 0.03 in 1.8 mmProvisionalWorked out: An assumption for the drawing, not a reading: the tube's rear end is inside the brace in every photo on file. Drawn as the reference model's mil-spec carbine tube's (std.receiver_extension.carbine_rear_wall, 0.072 in).
Worked out 0.072 in ± 0.03 in used
An assumption for the drawing, not a reading: the tube's rear end is inside the brace in every photo on file. Drawn as the reference model's mil-spec carbine tube's (std.receiver_extension.carbine_rear_wall, 0.072 in)., harvested
The tube's length (its front face to its rear)6.992 in ± 0.03 in 177.6 mmProvisionalWorked out: {.bore_depth} + {.rear_wall}
Worked out 6.992 in ± 0.03 in used
{.bore_depth} + {.rear_wall}, harvested
The brace's step between its positions1.313 in ± 0.03 in 33.3 mmCorroboratedWorked out: ({sb-tactical-sbpdw-brace.length_extended} - {sb-tactical-sbpdw-brace.length}) / 2
Worked out 1.3125 in ± 0.03 in used
({sb-tactical-sbpdw-brace.length_extended} - {sb-tactical-sbpdw-brace.length}) / 2, harvested
Three positions ("3-position adjustable"). Half the published travel from collapsed to extended: AR15Discounts' middle position is 1.375 in out and 1.25 short of extended, one seller's figures; the catalog moves by one step.
The housing's front face behind the takedown pin1.125 in ± 0.005 in 28.6 mmConfirmedWorked out: -{std.ar15.receiver_rear_x}
Worked out 1.125 in ± 0.005 in used
-{std.ar15.receiver_rear_x}, harvested
It bears on the receiver's rear face where an end plate does (AR15Discounts: "The end plate and castle nut are integral to the assembly").
The housing's length (its top, from its front face to the castle nut)2.02 in ± 0.03 in 51.3 mmProvisionalPhoto: the assembly alone from the right
Photo 2.02 in ± 0.03 in used
the assembly alone from the right, harvested
Scale: 169.2 px/in. Read by columns 1556 (its front face) to 1215 (the seam with the castle nut, a lit line 1210 to 1219 at row 400): 341 px
The housing's diameter round the tube1.418 in ± 0.02 in 36 mmProvisionalPhoto: the assembly alone from the right
Photo 1.418 in ± 0.02 in used
the assembly alone from the right, harvested
Scale: 169.2 px/in. Read by its top edge (row 382.5, columns 1230 to 1540) 120 px over the axis
The housing's bore (the tube passes through it)1.181 in ± 0.02 in 30 mmProvisionalWorked out: An assumption for the drawing, not a reading: the tube goes into the housing thread first ("With the tube inserted into the housing"), so the bore takes the thread's crests (std.receiver_extension.thread_major_d); no view on file shows its mouth square.
Worked out 1.1813 in ± 0.02 in used
An assumption for the drawing, not a reading: the tube goes into the housing thread first ("With the tube inserted into the housing"), so the bore takes the thread's crests (std.receiver_extension.thread_major_d); no view on file shows its mouth square., harvested
The housing's bores the brace's rods run in0.35 in ± 0.02 in 8.9 mmProvisionalWorked out: An assumption for the drawing, not a reading: the rods (sb-tactical-sbpdw-brace.rod_d, 0.334 in) slide in them; drawn 0.016 in over the rod. The front oblique photo (6020c5e68ca5) shows the two rods coming out of the housing's front face at its lower corners.
Worked out 0.35 in ± 0.02 in used
An assumption for the drawing, not a reading: the rods (sb-tactical-sbpdw-brace.rod_d, 0.334 in) slide in them; drawn 0.016 in over the rod. The front oblique photo (6020c5e68ca5) shows the two rods coming out of the housing's front face at its lower corners., harvested
The housing's wall outside each rod's bore0.09 in ± 0.04 in 2.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file is square to the housing's front or from below; the front oblique photo (6020c5e68ca5) shows a thin wall round each rod at the housing's lower corners.
Worked out 0.09 in ± 0.04 in used
An assumption for the drawing, not a reading: no view on file is square to the housing's front or from below; the front oblique photo (6020c5e68ca5) shows a thin wall round each rod at the housing's lower corners., harvested
The integral castle nut's length0.7 in ± 0.03 in 17.8 mmProvisionalPhoto: the assembly alone from the right
Photo 0.7 in ± 0.03 in used
the assembly alone from the right, harvested
Scale: 169.2 px/in. Read by columns 1215 (its seam with the housing) to 1097 (its rear face): 118 px
The integral castle nut's diameter1.389 in ± 0.02 in 35.3 mmProvisionalPhoto: the assembly alone from the right
Photo 1.389 in ± 0.02 in used
the assembly alone from the right, harvested
Scale: 169.2 px/in. Read by its top edge (row 385, columns 1100 to 1200) 117.5 px over the axis
The castle nut's notches: width0.11 in ± 0.02 in 2.8 mmProvisionalPhoto: the assembly alone from the right
Photo 0.11 in ± 0.02 in used
the assembly alone from the right, harvested
Scale: 169.2 px/in. Read by each of the two notches on this side, 17 px across, seen 22.5° off square (divided by cos 22.5°)
The castle nut's notches: depth from its rear face0.2 in ± 0.02 in 5.1 mmProvisionalPhoto: the assembly alone from the right
Photo 0.2 in ± 0.02 in used
the assembly alone from the right, harvested
Scale: 169.2 px/in. Read by columns 1097 to 1130: 33 px
The castle nut's notches: how many8ProvisionalPhoto: a photo on file
Photo 8 count used
a photo on file, harvested
Scale: a count. Read by six seen, at 22.5°, 67.5°, 112.5° off the horizontal each side; the pattern's two at the bottom hidden
Counted on the views that show them: two on the right side, each 0.267 in off the axis (22.5° on the nut's radius: rows 457 and 548 in c303ad6a4930), two on the left the same (73787978fd88), and two at the top either side of the middle in the view from behind (c3847cdcc54b). Eight at 45° turned 22.5° off the vertical puts a notch at each of those six places; the two at the bottom are behind the housing's lower part in every view.
The housing's underside below the tube's axis1.26 in ± 0.02 in 32 mmProvisionalPhoto: the assembly alone from the right
Photo 1.26 in ± 0.02 in used
the assembly alone from the right, harvested
Scale: 169.2 px/in. Read by its lower edge between the levers (row 716, columns 1330 to 1450) 213.5 px under the axis
The takedown lever's width across the rifle0.3 in ± 0.1 in 7.6 mmProvisionalWorked out: An assumption for the drawing, not a reading: the lever hangs from the housing's underside at its rear (its side seen square in c303ad6a4930); the obliques from behind (0d379b324f10, f1b3345f7383) show a flat tab about a third of the housing's width, and no view is square across it.
Worked out 0.3 in ± 0.1 in used
An assumption for the drawing, not a reading: the lever hangs from the housing's underside at its rear (its side seen square in c303ad6a4930); the obliques from behind (0d379b324f10, f1b3345f7383) show a flat tab about a third of the housing's width, and no view is square across it., harvested
The adjustment latch's width across the rifle0.35 in ± 0.1 in 8.9 mmProvisionalWorked out: An assumption for the drawing, not a reading: the ribbed latch under the housing's middle is seen square from the side only; the obliques show it a little wider than the takedown lever.
Worked out 0.35 in ± 0.1 in used
An assumption for the drawing, not a reading: the ribbed latch under the housing's middle is seen square from the side only; the obliques show it a little wider than the takedown lever., harvested
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
AR-15 receiver extension thread
- Lower receivers
- Aero Precision M4E1 complete lower, A2 grip and M4 stock, Aero Precision M4E1 Stripped Lower Receiver, Battle Arms Development Workhorse stripped lower, BCM MK2 AR-15 Lower Receiver, Bear Creek Arsenal BC-15 Multi Caliber, Lower Receiver, Black Anodized, Geissele Automatics Super Duty AR-15 Lower Receiver - Stripped Lower, Palmetto State Armory AR-15 "Stealth" Stripped Lower Receiver
- Folding stock adapters
- Law Tactical AR Folding Stock Adapter Gen 3-M, Law Tactical AR Folding Stock Adapter GEN-S, Sylvan Arms SA5 Pro AR15 Folding Stock Adapter (Opens To The Left), Sylvan Arms SA5 Pro AR15 Folding Stock Adapter (Opens To The Right)
Receiver extension (buffer tube)
Receiver extension bore
- Buffers
- Armaspec Stealth™ Recoil Spring - SRS™- AR15 GEN4, C (3.3 oz), Armaspec Stealth™ Recoil Spring - SRS™- AR15 GEN4, H (3.8 oz), Armaspec Stealth™ Recoil Spring - SRS™- AR15 GEN4, H2 (4.7 oz), Armaspec Stealth™ Recoil Spring - SRS™- AR15 GEN4, H3 (5.6 oz), BCM Carbine Buffer, BCM H Carbine Buffer, BCM H2 Carbine Buffer, BCM H3 Carbine Buffer, BCM MK2 Buffer Mod 1 - T0, Geissele Automatics Super 42 Braided Wire Buffer Spring and Buffer Combo, H1, Geissele Automatics Super 42 Braided Wire Buffer Spring and Buffer Combo, H2, Geissele Automatics Super 42 Braided Wire Buffer Spring and Buffer Combo, H3, Guntec USA AR-15 Mil-Spec Car Buffer, Guntec USA AR-15 Stainless Steel Car Buffer, JP Enterprises Silent Captured Spring AR-15 Heavy H2 GEN 2, JP Enterprises Silent Captured Spring AR-15 Heavy H3 GEN 2, JP Enterprises Silent Captured Spring AR-15 Standard GEN 2, KynSHOT RB5000, KynSHOT RB5000HP (High Performance), Panzer Arms AR57 proprietary carbine buffer, VLTOR A5H2 Buffer, 5.3 oz.
- Buffer springs
- BCM Carbine Action Spring, BCM Rifle M16 Action Spring, Guntec USA Upgraded Chrome Silicon Spring, VLTOR A5 Action Spring