Buffer
Armaspec Stealth™ Recoil Spring - SRS™- AR15 GEN4, H (3.8 oz)
A buffer weight and its spring captured on a guide rod as one unit, in the receiver extension in place of both the buffer and the action spring. The maker's page: "The Stealth Recoil Spring™ SRS™ GEN4 is a self-contained multi-stage drop-in replacement for your standard buffer and spring. The SRS™ is designed to keep the buffer spring from rubbing against the inner wall of the buffer tube providing smooth, quiet operation and the second stage helps reduce the felt recoil significantly." "COMPATIBILITY: AR-15 with carbine-length buffer tube"; "Most bolt carriers have a rear opening of over .60″, there are a couple of bolt carriers in the market place that have a rear opening of under .60″ and will not function with the SRS." "The polymer bumper goes towards the rear of the firearm and the metal weight mass goes towards the bolt carrier." "The SRS can be installed with our without the buffer retainer." The H's weight is a plain cylinder; the C's is necked, the H2's and the H3's are longer. The maker's guide names the H, or the H2, for a suppressed 5.56 with a 14.5 in barrel and a carbine gas system ("Perfect. A 3.8/SRS-H or a 4.7/SRS-H2 is what you need!").

- Weight
- 6.6 oz ± 0.05 oz Confirmedpublished: Armaspec, Stealth™ Recoil Spring - SRS™- AR15 GEN4 (the maker's page), the maker, read Oct 18, 2026
- Lowest price
- $76.49 at Primary Arms, read Nov 21, 2026
- Maker's number
- ARM253-H
- Colour
- Natural stainless
- Drawn as
- modelled
- Maker's page
- armaspec.com
In “BCM 16 in mid-length”, a build on the start page, in place of its BCM Carbine Buffer.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Length (the weight's front face to the bumper's rear face)7.18 in ± 0.005 in 182.4 mmConfirmedPublished: Armaspec, Stealth™ Recoil Spring - SRS™- AR15 GEN4 (the maker's page: one length for every version), the maker, read Oct 18, 2026
Published “Length: 7.18"” used
Armaspec, Stealth™ Recoil Spring - SRS™- AR15 GEN4 (the maker's page: one length for every version), the maker, read Oct 18, 2026 the page, harvested Oct 18, 2026
Published “7.18" Length”
Primary Arms, Armaspec Stealth AR-15 Recoil Spring - H 3.8 oz - Gen 4 (SKU: ARM253-H), a seller, read Oct 18, 2026 the page, harvested Oct 18, 2026
Published “SRS-H 7.18" 3.8 oz. 6.6 oz.”
Midwest Gun Works, Armaspec Gen 4 Stealth Recoil Spring, SRS-Kit (Code: ARM253-AR15KIT): its table's SRS-H row, a seller, read Oct 18, 2026 the page, harvested Oct 18, 2026
The maker's figure; two sellers repeat it. The maker's lineup photo has all four weights at one length end to end (983, 983, 984 and 981 px).
The buffer weight it stands for (the maker's "equivalent")3.8 oz ± 0.05 ozConfirmedPublished: Armaspec, Stealth™ Recoil Spring - SRS™- AR15 GEN4 (the maker's page), the maker, read Oct 18, 2026
Published “Equivalent Weight: C: 3.3 oz. H: 3.8 oz. H2: 4.7 oz. H3: 5.6 oz.” used
Armaspec, Stealth™ Recoil Spring - SRS™- AR15 GEN4 (the maker's page), the maker, read Oct 18, 2026 the page, harvested Oct 18, 2026
Not what it weighs: the standard buffer it is sold to take the place of, by weight class. The complete system is `weight`.
The weight's diameter (it runs in the extension's bore)0.946 in ± 0.015 in 24 mmProvisionalPhoto: the maker's lineup, 1161 px: the H second from the top
Photo 0.946 in ± 0.015 in used
the maker's lineup, 1161 px: the H second from the top, harvested
Scale: the unit's own length end to end, 983 px for the maker's 7.18 in. Read by the weight's silhouette, 129 to 130 px across along its length (the H's, the H2's and the H3's alike); the ± covers the camera's 1% and the edge
The bumper's diameter0.957 in ± 0.015 in 24.3 mmProvisionalPhoto: the maker's lineup
Photo 0.957 in ± 0.015 in used
the maker's lineup, harvested
Scale: the unit's own length end to end, 983 px for 7.18 in. Read by the bumper's silhouette, 130 to 131 px across in all four units
A hundredth more than the weight's in the one photo that sees both from square across; inside the extension's inch.
The bumper's length (the C's, the H's and the H2's)1.395 in ± 0.03 in 35.4 mmProvisionalPhoto: the maker's lineup
Photo 1.395 in ± 0.03 in used
the maker's lineup, harvested
Scale: the unit's own length end to end, 983 px for 7.18 in. Read by from the unit's rear end to where the silhouette falls from the bumper's 131 px to the spring's (191 px), the same in the top three units
The rod's end in the bumper's rear face0.33 in ± 0.03 in 8.4 mmProvisionalPhoto: Primary Arms' ARM253-H_02: the bumper's rear face seen at an angle, PAT. USD864337 and PAT. US8800424 engraved on it
Photo 0.33 in ± 0.03 in used
Primary Arms' ARM253-H_02: the bumper's rear face seen at an angle, PAT. USD864337 and PAT. US8800424 engraved on it, harvested
Scale: the face's own diameter (bumper_d), in its plane. Read by the steel disc's width across the face's ellipse along its long axis, 0.34 of the face's
The slot across the bumper's rear face (the roll pin lies in it)0.048 in ± 0.015 in 1.2 mmProvisionalPhoto: Primary Arms' ARM253-H_02, the bumper's rear face
Photo 0.048 in ± 0.015 in used
Primary Arms' ARM253-H_02, the bumper's rear face, harvested
Scale: the face's own diameter (bumper_d), in its plane. Read by the slot's width square to its length, a twentieth of the face's
The maker's page: "we changed the screw to a roll pin across the plastic end piece".
The slot's depth in the bumper's rear face, to the pin0.1 in ± 0.05 in 2.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows the slot in profile; the pin is seen at its floor.
Worked out 0.1 in ± 0.05 in used
An assumption for the drawing, not a reading: no view on file shows the slot in profile; the pin is seen at its floor., harvested
How far the rod's end runs into the bumper at its larger size0.3 in ± 0.15 in 7.6 mmProvisionalWorked out: An assumption for the drawing, not a reading: the rod's end is seen only in the bumper's rear face.
Worked out 0.3 in ± 0.15 in used
An assumption for the drawing, not a reading: the rod's end is seen only in the bumper's rear face., harvested
The rod's diameter under the main spring0.176 in ± 0.02 in 4.5 mmProvisionalPhoto: the maker's arm253-h_3_1.jpg, 1800 px, near side-on
Photo 0.176 in ± 0.02 in used
the maker's arm253-h_3_1.jpg, 1800 px, near side-on, harvested
Scale: the weight's own diameter (od) in the same photo, 204 px. Read by the narrowest dark run through the axis between the coils, 35 to 41 px, behind the bumper's front face
The rod's diameter under the second spring (washer to weight)0.39 in ± 0.03 in 9.9 mmProvisionalPhoto: the maker's arm253-h_3_1.jpg
Photo 0.39 in ± 0.03 in used
the maker's arm253-h_3_1.jpg, harvested
Scale: the weight's own diameter (od) in the same photo, 204 px. Read by the dark run through the axis between the second spring's coils, 82 to 87 px
The washer between the two springs, its diameter0.709 in ± 0.015 in 18 mmProvisionalPhoto: the maker's lineup
Photo 0.709 in ± 0.015 in used
the maker's lineup, harvested
Scale: the unit's own length end to end, 983 px for 7.18 in. Read by 97 px across, in all four units
The washer's length along the rod0.212 in ± 0.02 in 5.4 mmProvisionalPhoto: the maker's lineup
Photo 0.212 in ± 0.02 in used
the maker's lineup, harvested
Scale: the unit's own length end to end, 983 px for 7.18 in. Read by its run at 97 px across, from 575 to 604 px from the unit's rear end (the H3's 528 to 560)
Where the washer's front face stands, behind the weight's front face (the C, the H and the H2)2.768 in ± 0.02 in 70.3 mmProvisionalPhoto: the maker's lineup
Photo 2.768 in ± 0.02 in used
the maker's lineup, harvested
Scale: the unit's own length end to end, 983 px for 7.18 in. Read by 604 px from the unit's rear end in the top three units: 379 px from the front
The main spring's outside diameter0.394 in ± 0.02 in 10 mmProvisionalPhoto: the maker's lineup
Photo 0.394 in ± 0.02 in used
the maker's lineup, harvested
Scale: the unit's own length end to end, 983 px for 7.18 in. Read by the envelope of the coils' crests, 54 px
The main spring's wire0.034 in ± 0.008 in 0.9 mmProvisionalPhoto: the maker's arm253-h_3_1.jpg
Photo 0.034 in ± 0.008 in used
the maker's arm253-h_3_1.jpg, harvested
Scale: the weight's own diameter (od) in the same photo, 204 px. Read by a coil's wire square across its run where it crosses the rod, 7 px
The main spring's coils25 ± 1ProvisionalPhoto: the H), 7b6e26a86e96 (the C), 228008b8823f (the H2), 5a44c78c3155 (the H3
Photo 25 count ± 1 count used
the H), 7b6e26a86e96 (the C), 228008b8823f (the H2), 5a44c78c3155 (the H3, harvested
Scale: none: a count. Read by counted along the top of the silhouette on the H's photo, bumper to washer (25, the last against the washer); the pitch by the brightness's autocorrelation along it, 22.8 to 24.9 px in the four photos, gives 24 to 27 over the run
The second (front) spring's outside diameter0.65 in ± 0.02 in 16.5 mmProvisionalPhoto: the maker's lineup
Photo 0.65 in ± 0.02 in used
the maker's lineup, harvested
Scale: the unit's own length end to end, 983 px for 7.18 in. Read by the envelope of the coils' crests, 89 px
The second spring's wire0.045 in ± 0.01 in 1.1 mmProvisionalPhoto: the maker's H and C side views
Photo 0.045 in ± 0.01 in used
the maker's H and C side views, harvested
Scale: the weight's own diameter (od) in the same photo. Read by a coil's wire square across its run, 9 to 11 px
The second spring's coils10 ± 1ProvisionalPhoto: the H) and 7b6e26a86e96 (the C
Photo 10 count ± 1 count used
the H) and 7b6e26a86e96 (the C, harvested
Scale: none: a count. Read by the wire's crossings along the top of the silhouette, washer to weight: two closed at the washer, six open, two closed at the weight, in both
The bore in the weight's front face (the rod's cap is at its floor)0.61 in ± 0.03 in 15.5 mmProvisionalPhoto: Primary Arms' ARM253-H_01: the weight's front face seen at an angle
Photo 0.61 in ± 0.03 in used
Primary Arms' ARM253-H_01: the weight's front face seen at an angle, harvested
Scale: the face's own diameter (od), in its plane. Read by the bore's ellipse over the face's, 0.653 along the long axis and 0.633 along the short
How deep in the weight's front bore the rod's cap stands (free, out of the rifle)0.3 in ± 0.15 in 7.6 mmProvisionalWorked out: An assumption for the drawing, not a reading: the cap is seen at the bore's floor in Primary Arms' oblique photo, and no view gives the depth.
Worked out 0.3 in ± 0.15 in used
An assumption for the drawing, not a reading: the cap is seen at the bore's floor in Primary Arms' oblique photo, and no view gives the depth., harvested
The rod's cap ("the cap is machined on the rod")0.5 in ± 0.08 in 12.7 mmProvisionalWorked out: An assumption for the drawing, not a reading: it holds the weight on the rod, so it is wider than the rod under the weight and narrower than the bore it sits in.
Worked out 0.5 in ± 0.08 in used
An assumption for the drawing, not a reading: it holds the weight on the rod, so it is wider than the rod under the weight and narrower than the bore it sits in., harvested
The cap's thickness0.08 in ± 0.04 in 2 mmProvisionalWorked out: An assumption for the drawing, not a reading.
Worked out 0.08 in ± 0.04 in used
An assumption for the drawing, not a reading., harvested
The edges' break on the weight, the washer and the bumper0.02 in ± 0.01 in 0.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: the edges read rounded at the photos' size, by a pixel or two.
Worked out 0.02 in ± 0.01 in used
An assumption for the drawing, not a reading: the edges read rounded at the photos' size, by a pixel or two., harvested
The H's weight, its length1.264 in ± 0.02 in 32.1 mmProvisionalPhoto: the maker's lineup, the H second from the top
Photo 1.264 in ± 0.02 in used
the maker's lineup, the H second from the top, harvested
Scale: the unit's own length end to end, 983 px for 7.18 in. Read by from its rear face (810 px from the unit's rear end) to its front (983)
The pocket in the weight's rear face that the second spring's end goes into0.68 in ± 0.03 in 17.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: wider than the spring it takes (second_spring_od, 0.65) and inside the weight's 0.946; no view sees into it.
Worked out 0.68 in ± 0.03 in used
An assumption for the drawing, not a reading: wider than the spring it takes (second_spring_od, 0.65) and inside the weight's 0.946; no view sees into it., harvested
Seen in every side view: the second spring's last coil goes in behind the weight's rear rim (954e1211557e, the H), and the H2's and the H3's weights hide several coils of it (228008b8823f, 5a44c78c3155).
The cross hole in the rod ahead of the washer (for a hex key, as a lever)0.11 in ± 0.02 in 2.8 mmProvisionalWorked out: A 3/32 in hex key goes through it (Redcon1's sentence, https://redcon1tactical.com/armaspec-ar-15-stealth-recoil-spring-srs-carbine-gen4-c-3-3-oz.html): drawn at the key's size across its corners, 0.094 / cos 30°. Not a reading of the hole.
Worked out 0.11 in ± 0.02 in used
A 3/32 in hex key goes through it (Redcon1's sentence, https://redcon1tactical.com/armaspec-ar-15-stealth-recoil-spring-srs-carbine-gen4-c-3-3-oz.html): drawn at the key's size across its corners, 0.094 / cos 30°. Not a reading of the hole., harvested
Redcon1's installation text: "re-tighten the screws using either using two 3/32 hex keys and fully tightening both screws at the same time or using one 3/32 hex key and using the hole in the rod for leverage." Seen in the maker's side view of the H2 (228008b8823f) at the thick rod's lower edge, just ahead of the washer, partly under the spring's first coil.
How far ahead of the washer's front face the rod's cross hole's middle is0.06 in ± 0.03 in 1.5 mmProvisionalPhoto: the maker's arm253-h2_3_1.jpg, 1800 px
Photo 0.06 in ± 0.03 in used
the maker's arm253-h2_3_1.jpg, 1800 px, harvested
Scale: the unit's own length end to end, 1500 px for 7.18 in. Read by the hole's visible part 7 to 12 px ahead of the washer's front face, under the first coil; the ± covers what the coil hides
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Receiver extension bore
- Receiver extensions
- BCM Milspec Carbine Receiver Extension (Buffer Tube) 6 Position, BCM MK2 Receiver Extension, Geissele Automatics Premium Mil-Spec Buffer Tube, Guntec USA AR-15 Mil-Spec Buffer Tube (Gen 2), SB Tactical SBPDW receiver extension, housing and integral castle nut, VLTOR RE-A5 7-Position Receiver Extension, MilSpec Diameter
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Primary Arms $76.49 Nov 21, 2026, in stock that day
- MidwayUSA $76.49 Nov 21, 2026, in stock that day
- Midwest Gun Works $76.49 Nov 21, 2026, in stock that day
- Redcon1 Tactical $76.49 Nov 21, 2026, out of stock that day