Receiver extension
VLTOR RE-A5 7-Position Receiver Extension, MilSpec Diameter
VLTOR's A5 receiver extension: a mil-spec diameter tube 11/16 in longer than a carbine one, with seven stock positions, for the A5 buffer and the rifle-length spring. VLTOR: "The RE-A5 Receiver Extension is a 7-position receiver extension tube designed to work with the VLTOR A5 Buffer System. This receiver extension is slightly longer than the traditional M4 receiver extension and is designed to work with Mil-Spec dimensioned M4/AR-15 type collapsible stocks." "Seven position receiver extension made from impact extruded 7075 T6 aluminum", "Type III Hard coat anodized black", "Dry Film Lube applied to interior surface", "Adjustment positions are numbered and are visible through the witness hole on most stocks". Sold alone and in VLTOR's A5 Buffer Kit (SKU "RE-A5 and SP-A5": the tube, the A5H2 buffer, the A5 buffer spring, VLTOR's lockplate and castle nut).

- Weight
- 4.3 oz Confirmedpublished: VLTOR, RE-A5 7-Position Receiver Extension, MilSpec Diameter (SKU RE-A5), SPECIFICATIONS, the maker, read Oct 28, 2026
- Lowest price
- $56.66 at Primary Arms, read Nov 21, 2026
- Maker's number
- RE-A5
- Colour
- Black (placeholder)
- Drawn as
- modelled
- Maker's page
- vltor.com
In “Two-tone 16 in, Stealth Gray and soft-shooting”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
The tube's outside diameter1.148 in 29.2 mmConfirmedWorked out: {std.receiver_extension.milspec_od}
Worked out 1.148 in used
{std.receiver_extension.milspec_od}, harvested
The standard mil-spec carbine tube's: VLTOR sells it as "MilSpec Diameter".
VLTOR names the tube "RE-A5 7-Position Receiver Extension, MilSpec Diameter" (its product page) and calls it "a 7-position mil-spec receiver extension" that "accepts any standard mil-spec collapsible stock" (https://vltor.com/a5); no page states a figure.
The tube's length7.938 in ± 0.031 in 201.6 mmConfirmedPublished: VLTOR, RE-A5 7-Position Receiver Extension, MilSpec Diameter (SKU RE-A5), SPECIFICATIONS, the maker, read Oct 28, 2026
Published “Length 7 15/16"” used
VLTOR, RE-A5 7-Position Receiver Extension, MilSpec Diameter (SKU RE-A5), SPECIFICATIONS, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
A sixteenths figure: a thirty-second either way.
Published “SKU RE-A5 Overall Length 7 15/16"”
VLTOR, A5 Buffer System page, its RE-A5 RECEIVER EXTENSION table, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
The product page's own figure; the A5 page says the same and calls it the overall length.
VLTOR's A5 page: "The RE-A5 tube is 3/4" longer than a standard carbine tube" (7 15/16 is 11/16 longer than the mil-spec carbine tube's 7.25 on Magpul's drawing, std.receiver_extension's source; the 3/4 is a round figure).
The tube's front face behind the takedown pin (how far it screws in)0.669 in ± 0.02 in 17 mmConfirmedWorked out: -{std.receiver_extension.front_face_x}
Worked out 0.669 in ± 0.02 in used
-{std.receiver_extension.front_face_x}, harvested
The Army's drawings: a mil-spec tube is screwed in until its edge stands over the buffer retainer's shoulder.
Hidden inside the receiver: what it moves is the relief, the rail's lip and ramp, the channel and the seven holes. VLTOR's thread is the mil-spec one ("Thread 1-3/16 x 16 (mil-spec)", https://vltor.com/a5).
The stock position step0.65 in ± 0.0005 in 16.5 mmConfirmedPublished: VLTOR, A5 Buffer System page, its RE-A5 RECEIVER EXTENSION table, the maker, read Oct 28, 2026
Published “Position Spacing 0.650"” used
VLTOR, A5 Buffer System page, its RE-A5 RECEIVER EXTENSION table, the maker, read Oct 28, 2026 the page, harvested Oct 28, 2026
Photo 0.651 in ± 0.01 in
VLTOR's photograph of the tube standing on its rear face, the rail's channel toward the left and toward the lens, 2359 x 1572, harvested
Scale: the tube's length (tube_length, 7 15/16 in) from its mouth (the rim's middle, 142 px) to its rear face (1460 px): 166 px/in along the tube. Read by the lit rims of six holes seen in the channel, the brightest row of each in a column down the channel (x 1068 to 1095): 727, 837, 946, 1053, 1160, 1267 px, 108.0 px apart on average (540 px over five steps)
The maker's figure; VLTOR's photograph of the tube's holes gives the same.
The position holes' diameter (in the rail's channel)0.3 in ± 0.04 in 7.6 mmProvisionalPhoto: VLTOR's photograph of the tube standing, the channel toward the lens at a slant; a crop of x 1050 to 1110, y 680 to 1000 at four times with its levels stretched, an.holes
Photo 0.3 in ± 0.04 in used
VLTOR's photograph of the tube standing, the channel toward the lens at a slant; a crop of x 1050 to 1110, y 680 to 1000 at four times with its levels stretched, an.holes, harvested
Scale: the tube's length (tube_length, 7 15/16 in), 166 px/in along the tube; the holes' own pitch (position_step, 0.650) gives 164. Read by each hole shows as a half circle standing out of the channel's far wall (wider than the channel); its length along the tube, the one size a slant view keeps: 52 and 50 px for the second and third holes
Narrower than the 0.42 read on BCM's mil-spec tube (bcm-receiver-extension.position_hole_d).
The rear (seventh) position hole's centre ahead of the tube's rear face0.63 in ± 0.05 in 16 mmProvisionalPhoto: the holes in the channel, an.holes) and ffe8eb512fc6 (VLTOR's photograph of the tube standing, its numbered side toward the lens, 2317 x 1544
Photo 0.63 in ± 0.05 in used
the holes in the channel, an.holes) and ffe8eb512fc6 (VLTOR's photograph of the tube standing, its numbered side toward the lens, 2317 x 1544, harvested
Scale: the holes' own pitch (position_step, 0.650 in): 106.5 px a step in 4b0990a26750, 163.8 px/in; the tube's length (164 px/in) in ffe8eb512fc6. Read by the middles of the half circles the first three holes make in the channel's wall, 717, 824 and 930 px, carried on at the pitch to the seventh, 1356 px: 104 px (0.635 in) ahead of the rear face at 1460. The engraved 7 beside it in ffe8eb512fc6 (the white figure's middle, 1363 px; rear face 1460): 0.64 in. The two agree.
The channel along the rail's underside, its front end ahead of the tube's rear face4.64 in ± 0.08 in 117.9 mmProvisionalPhoto: VLTOR's photograph of the tube standing, the channel toward the lens at a slant
Photo 4.64 in ± 0.08 in used
VLTOR's photograph of the tube standing, the channel toward the lens at a slant, harvested
Scale: the tube's length (tube_length, 7 15/16 in), 166 px/in along the tube (mouth 142 px, rear face 1460 px). Read by the channel's front rounded end at 690 px on a crop with its levels stretched (an.c1): 3.30 in behind the mouth, 4.64 ahead of the rear face
The RE-A5 has a long recess along its rail's underside with rounded ends, the seven holes in its floor: VLTOR's 4b0990a26750 shows it from the side and below as a dark slot from the ramp's foot almost to the rear end.
The channel along the rail's underside, its rear end ahead of the tube's rear face0.35 in ± 0.1 in 8.9 mmProvisionalPhoto: VLTOR's photograph of the tube standing, the channel toward the lens at a slant
Photo 0.35 in ± 0.1 in used
VLTOR's photograph of the tube standing, the channel toward the lens at a slant, harvested
Scale: the tube's length (tube_length, 7 15/16 in), 166 px/in along the tube. Read by the channel's rear rounded end at 1400 px, 60 px ahead of the rear face (1460 px). The rear face's own photograph (20475bac1645) has the rail's rear end whole under the tube, so the channel stops short of it.
The channel along the rail's underside, its width0.25 in ± 0.06 in 6.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows the rail's underside square on. In 4b0990a26750 the channel is about three fifths of the rail's face as it is seen, with flats either side of it, and each hole (position_hole_d, 0.30) stands out of its far wall as a half circle: the channel is narrower than the holes.
Worked out 0.25 in ± 0.06 in used
An assumption for the drawing, not a reading: no view on file shows the rail's underside square on. In 4b0990a26750 the channel is about three fifths of the rail's face as it is seen, with flats either side of it, and each hole (position_hole_d, 0.30) stands out of its far wall as a half circle: the channel is narrower than the holes., harvested
The channel along the rail's underside, its depth0.08 in ± 0.04 in 2 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows the channel in section. In 4b0990a26750 (an.holes) its inside is dark from wall to wall and the holes' rims stand in its far wall as half circles, so it is deeper than a skin cut; under half the rail's depth below the tube is left for the holes.
Worked out 0.08 in ± 0.04 in used
An assumption for the drawing, not a reading: no view on file shows the channel in section. In 4b0990a26750 (an.holes) its inside is dark from wall to wall and the holes' rims stand in its far wall as half circles, so it is deeper than a skin cut; under half the rail's depth below the tube is left for the holes., harvested
The rail's ramp, where it leaves the lip, behind the tube's front face2.33 in ± 0.05 in 59.2 mmProvisionalPhoto: VLTOR's two photographs of the tube standing, the rail to the right in one and to the left in the other
Photo 2.33 in ± 0.05 in used
VLTOR's two photographs of the tube standing, the rail to the right in one and to the left in the other, harvested
Scale: the tube's length (tube_length, 7 15/16 in): 164 and 166 px/in along the tube. Read by where the rail's silhouette leaves the tube's, its edge's run along the ramp extended back to the body's edge: 540 px in ffe8eb512fc6 (mouth 155), 2.35 in; 526 px in 4b0990a26750 (mouth 142), 2.31 in
The mil-spec carbine tube's ramp on Magpul's drawing begins 2.326 behind its front face and is at full depth by 2.592, at 45° (std.receiver_extension.rail_ramp_start, rail_ramp_end); VLTOR's begins at the same place and runs down at about 32° to full depth half an inch further back (rail_ramp_end).
The rail's ramp, where it reaches the rail's full depth, behind the tube's front face2.8 in ± 0.05 in 71.1 mmProvisionalPhoto: a photo on file
Photo 2.8 in ± 0.05 in used
a photo on file, harvested
Scale: the tube's length (tube_length, 7 15/16 in): 164 and 166 px/in along the tube. Read by where the rail's silhouette stops growing: 622 px in ffe8eb512fc6 (2.85 in from the mouth at 155), 604 px in 4b0990a26750 (2.78 in from 142)
The rail's lip ahead of the ramp, how far it stands under the tube0.04 in ± 0.02 in 1 mmProvisionalPhoto: the tube standing, the rail to the left and turned toward the lens
Photo 0.04 in ± 0.02 in used
the tube standing, the rail to the left and turned toward the lens, harvested
Scale: the tube's length (tube_length, 7 15/16 in), 166 px/in. Read by the lip's edge 4 to 6 px outside the tube's own edge between the relief and the ramp (rows 412 to 512, 1099 px against 1103 to 1105 above it). The rail is turned toward the lens in this view, so what shows is its depth foreshortened and a little of its width: the ± is that.
Between the relief behind the thread and the ramp the rail is a low lip under the tube (VLTOR's "VLTOR PAT PEND RE-A5" is engraved on its side), as on the mil-spec tube.
The relief behind the thread, where the tube's full diameter begins, behind its front face1.51 in ± 0.04 in 38.4 mmProvisionalPhoto: the tube standing, 2317 x 1544) and 4b0990a26750 as the kit's picture uses it (a copy on file, lying, 718 px long
Photo 1.51 in ± 0.04 in used
the tube standing, 2317 x 1544) and 4b0990a26750 as the kit's picture uses it (a copy on file, lying, 718 px long, harvested
Scale: the tube's length (tube_length, 7 15/16 in): 164 px/in in ffe8eb512fc6; 90.5 px/in in ba600a518974. Read by the shoulder where the edge steps out from the relief to the body: 405 px in ffe8eb512fc6 (1.52 in from the mouth at 155; the relief is 181 px across against the body's 185); 386 px in ba600a518974 (1.51 in from the mouth at 249), where the rail's lip begins under it
Behind the thread's last crest the tube runs on a little under its own diameter, at about the thread's root, to a shoulder where the tube's body and the rail's lip begin: a thread relief.
The thread's length, from the mouth to its last crest1.1 in ± 0.04 in 27.9 mmConflictPhoto: the tube standing, its left edge's crests) and 4b0990a26750 as the kit's picture uses it (a copy on file, its top edge's crests
Photo 1.1 in ± 0.04 in used
the tube standing, its left edge's crests) and 4b0990a26750 as the kit's picture uses it (a copy on file, its top edge's crests, harvested
Scale: the thread's own pitch, 1/16 in (std.receiver_extension.thread_pitch): 10.06 px a crest in ffe8eb512fc6, 5.6 px in ba600a518974. Read by from the mouth to the last crest: in ffe8eb512fc6 a plain lip (163 to 172 px), a run-in, then 15 crests 185 to 326 px and the last at 331, 176 px from the mouth at 155 (17.5 turns, 1.09 in); in ba600a518974 crests from 262 to 349 px, 100 px from the mouth at 249 (1.10 in)
Worked out 1.181 in ± 0.01 in
{std.receiver_extension.thread_length}, harvested
The reference model's carbine tube's.
VLTOR's own tube, counted on two of its photographs that agree; the reference model's carbine tube is another maker's thread, a turn and a quarter longer.
photo and std differ by 0.081 in beyond what each states it is good to.
VLTOR's thread is the mil-spec one: "Thread 1-3/16 x 16 (mil-spec)" (https://vltor.com/a5). How far it runs back is VLTOR's own: its crests counted on its photographs.
The rear wall's thickness, inside the tube0.072 in ± 0.02 in 1.8 mmProvisionalWorked out: An assumption for the drawing, not a reading: no page states the RE-A5's bore length and no view shows inside it. Taken as the mil-spec carbine tube's on the reference model (std.receiver_extension.carbine_rear_wall, 0.072): VLTOR's rear face (20475bac1645) is closed, flat and engraved, with a small hole at its middle, as the carbine tube's is.
Worked out 0.072 in ± 0.02 in used
An assumption for the drawing, not a reading: no page states the RE-A5's bore length and no view shows inside it. Taken as the mil-spec carbine tube's on the reference model (std.receiver_extension.carbine_rear_wall, 0.072): VLTOR's rear face (20475bac1645) is closed, flat and engraved, with a small hole at its middle, as the carbine tube's is., harvested
The round on the rear face's outer edge0.04 in ± 0.02 in 1 mmProvisionalWorked out: An assumption for the drawing, not a reading: VLTOR's photograph of the rear face (20475bac1645) shows its outer edge, and the rail's rear corners, broken by a small round that catches the light all round, a few hundredths of an inch across against the 1.148 face; it isn't seen in profile.
Worked out 0.04 in ± 0.02 in used
An assumption for the drawing, not a reading: VLTOR's photograph of the rear face (20475bac1645) shows its outer edge, and the rail's rear corners, broken by a small round that catches the light all round, a few hundredths of an inch across against the 1.148 face; it isn't seen in profile., harvested
The relief behind the thread, its diameter1.123 in ± 0.015 in 28.5 mmProvisionalPhoto: the tube standing, 2317 x 1544
Photo 1.123 in ± 0.015 in used
the tube standing, 2317 x 1544, harvested
Scale: the tube's own outside diameter beside it (tube_od, 1.148 in): the relief and the body are the same black at the same depth, so their silhouettes thin alike and their ratio holds. Read by the silhouette's width, rows 336 to 404 against rows 420 to 530 (threshold 200): 181 px against 185 px; 1.148 x 181/185. Between the thread's roots (std.receiver_extension.thread_minor_d, 1.109) and the body.
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
AR-15 receiver extension thread
- Lower receivers
- Aero Precision M4E1 complete lower, A2 grip and M4 stock, Aero Precision M4E1 Stripped Lower Receiver, Battle Arms Development Workhorse stripped lower, BCM MK2 AR-15 Lower Receiver, Bear Creek Arsenal BC-15 Multi Caliber, Lower Receiver, Black Anodized, Geissele Automatics Super Duty AR-15 Lower Receiver - Stripped Lower, Palmetto State Armory AR-15 "Stealth" Stripped Lower Receiver
- Folding stock adapters
- Law Tactical AR Folding Stock Adapter Gen 3-M, Law Tactical AR Folding Stock Adapter GEN-S, Sylvan Arms SA5 Pro AR15 Folding Stock Adapter (Opens To The Left), Sylvan Arms SA5 Pro AR15 Folding Stock Adapter (Opens To The Right)
Receiver extension (buffer tube)
- Stocks
- B5 Systems Bravo Stock, B5 Systems Enhanced SOPMOD Stock, BCM Stock - Mod 0, Magpul CTR carbine stock, mil-spec, Magpul MOE carbine stock, mil-spec, Magpul MOE SL carbine stock, mil-spec, Mission First Tactical BATTLELINK Minimalist Milspec Stock
- Braces
- SB Tactical SBA3® AR Adjustable Pistol Stabilizing Brace®, SB Tactical SBA4® AR Adjustable Pistol Stabilizing Brace®, SB Tactical SBA5® AR Adjustable Pistol Stabilizing Brace®
Receiver extension end
Receiver extension bore
- Buffers
- Armaspec Stealth™ Recoil Spring - SRS™- AR15 GEN4, C (3.3 oz), Armaspec Stealth™ Recoil Spring - SRS™- AR15 GEN4, H (3.8 oz), Armaspec Stealth™ Recoil Spring - SRS™- AR15 GEN4, H2 (4.7 oz), Armaspec Stealth™ Recoil Spring - SRS™- AR15 GEN4, H3 (5.6 oz), BCM Carbine Buffer, BCM H Carbine Buffer, BCM H2 Carbine Buffer, BCM H3 Carbine Buffer, BCM MK2 Buffer Mod 1 - T0, Geissele Automatics Super 42 Braided Wire Buffer Spring and Buffer Combo, H1, Geissele Automatics Super 42 Braided Wire Buffer Spring and Buffer Combo, H2, Geissele Automatics Super 42 Braided Wire Buffer Spring and Buffer Combo, H3, Guntec USA AR-15 Mil-Spec Car Buffer, Guntec USA AR-15 Stainless Steel Car Buffer, JP Enterprises Silent Captured Spring AR-15 Heavy H2 GEN 2, JP Enterprises Silent Captured Spring AR-15 Heavy H3 GEN 2, JP Enterprises Silent Captured Spring AR-15 Standard GEN 2, KynSHOT RB5000, KynSHOT RB5000HP (High Performance), Panzer Arms AR57 proprietary carbine buffer, VLTOR A5H2 Buffer, 5.3 oz.
- Buffer springs
- BCM Carbine Action Spring, BCM Rifle M16 Action Spring, Guntec USA Upgraded Chrome Silicon Spring, VLTOR A5 Action Spring
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Primary Arms $56.66 Nov 21, 2026, in stock that day
- VLTOR $62.95 Nov 21, 2026, out of stock that day