Buffer
BCM MK2 Buffer Mod 1 - T0
The intermediate-length buffer of BCM's MK2 recoil mitigation system, the lightest of its five weights (T0 to T4). BCM: "THE BCM® MK2 BUFFER MOD1- T0, Intermediate Length (BUFFER ONLY) (weight = approximately 3.8oz)"; "Increased internal counterweight travel reduces bolt bounce"; "Internal spring to reduce noise of counter weight shifting and ensure more consistent weight placement"; "Made of 7075T6 aluminum, hard coat anodized for lasting endurance." "BCM US Patent #10415907". BCM recommends "heavier buffer weights for short barreled and suppressed platforms, starting with the T0 buffer weight and increasing to T1, or more as needed based on performance" (its MK2 RMS page).

- Weight
- 3.8 oz ± 0.1 oz Confirmedpublished: Bravo Company USA, BCM MK2 Buffer Mod 1 - T0 (BCM-BFMK2-M1-T0), the maker, read Oct 28, 2026
- Lowest price
- $36.95 at BCM, read Nov 21, 2026
- Maker's number
- BCM-BFMK2-M1-T0
- Colour
- Black (placeholder)
- Drawn as
- modelled
- Maker's page
- bravocompanyusa.com
In “Drop-in 16 in, Stealth Gray on BCM's MK2 lower”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Length (the head's front face to the bumper's end)4.046 in ± 0.04 in 102.8 mmConflictPhoto: BCM's MK2-GFSK-STOCK-KIT-BLK: the Mod 2 stock kit with the MK2 tube, an M16 spring and this buffer laid flat on white, from above, 1000 x 667
Photo 4.046 in ± 0.04 in used
BCM's MK2-GFSK-STOCK-KIT-BLK: the Mod 2 stock kit with the MK2 tube, an M16 spring and this buffer laid flat on white, from above, 1000 x 667, harvested
Scale: the MK2 tube beside it, 525.5 px for its 7.955 in (bcm-mk2-receiver-extension.tube_length): 66.06 px/in; at that scale the free spring is 12.48 in (the Army's 12.50) and the head 0.984 (the standard's 0.98). Read by its silhouette on its axis row (y 566): the bumper's end at x 720.0 (the cream urethane against white, threshold 240) to the head's front face at 987.3: 267.3 px
BCM's photo of the T0 standing upright (a copy on file) has it 5.75 body widths long: 4.05 in for the standard 0.687 body, though taken from close by.
Photo 4.35 in ± 0.05 in
BCM's BUFFER_ASSY_MK2_INTERMEDIATE: an exploded line drawing of the assembly, 3784 x 4898, on the kit's page, harvested
Scale: its head's 289 px as the standard's 0.98 (a head that runs in the extension's 1.000 bore): 295 px/in. Read by the body from its head's front face (x 25) to its open end (1153), 3.82 in, and the bumper from its shoulder (3600) to its end (3757), 0.53 in, added
BCM's illustration has a thicker head (0.36 in) and a bumper standing 0.53 out, where both photos of the buffer have the standard's 0.25 and 0.4: an illustration, not drawn to the product's proportions.
BCM's photo of the buffer beside the tube, at a scale three published figures bear out (the tube's thread, the Army's spring, the standard head); a second photo agrees. BCM's illustration is 7% longer and its head and bumper are not the photos' proportions.
photo and bcm-drawing differ by 0.304 in beyond what each states it is good to.
Diameter (its head, which runs in the extension's bore)0.98 in ± 0.005 in 24.9 mmConfirmedWorked out: {std.carbine_buffer.head_d}
Worked out 0.98 in ± 0.005 in used
{std.carbine_buffer.head_d}, harvested
Photo 0.984 in ± 0.03 in
BCM's stock kit photo on white, 1000 x 667, harvested
Scale: 66.06 px/in (length). Read by the head's silhouette across, x 974 to 984: 65 px
The standard head; BCM's photo has it to a pixel.
The head's thickness (the flange the spring bears on)0.254 in ± 0.005 in 6.5 mmProvisionalWorked out: {std.carbine_buffer.head_thickness}
Worked out 0.254 in ± 0.005 in used
{std.carbine_buffer.head_thickness}, harvested
Photo 0.247 in ± 0.03 in
BCM's stock kit photo on white, 1000 x 667, harvested
Scale: 66.06 px/in (length). Read by the head's full-diameter run, x 971 to 987.3: 16.3 px
The standard's; BCM's photo agrees within it.
The collar behind the head (what the spring's end coil sits over)0.781 in ± 0.001 in 19.8 mmCorroboratedWorked out: {std.carbine_buffer.pilot_d}
Worked out 0.781 in ± 0.001 in used
{std.carbine_buffer.pilot_d}, harvested
Photo 0.772 in ± 0.03 in
BCM's stock kit photo on white, 1000 x 667, harvested
Scale: 66.06 px/in (length). Read by the collar's silhouette, x 954 to 968: 51 px; it ends at x 951, 0.55 in behind the face (the standard's body begins at 0.51)
The standard's; BCM's photo agrees within it.
How far the bumper stands out of the body0.4 in ± 0.01 in 10.2 mmConfirmedWorked out: {std.carbine_buffer.bumper_exposed}
Worked out 0.4 in ± 0.01 in used
{std.carbine_buffer.bumper_exposed}, harvested
Photo 0.42 in ± 0.03 in
BCM's stock kit photo on white, 1000 x 667, harvested
Scale: 66.06 px/in (length). Read by the cream urethane from its end (x 720.0) to the black body (747.8): 27.8 px; its end 34 px across, widening at 13 degrees to the body's
BCM's drawing: "MIL-SPEC Polyether Urethane Bumper ... Modified to fit Pre-load Spring with Integral Over-travel Stop": changed inside; outside, its photos have the standard's.
The standard bumper's (the Army's drawing); BCM's photo agrees within its ±.
The body's length (the head's front face to the body's open end)3.646 in ± 0.04 in 92.6 mmProvisionalWorked out: {.length} - {.bumper_exposed}
Worked out 3.646 in ± 0.04 in used
{.length} - {.bumper_exposed}, harvested
Photo 3.626 in ± 0.03 in
BCM's stock kit photo on white, 1000 x 667, harvested
Scale: 66.06 px/in (length). Read by from the head's face (x 987.3) to where the body meets the cream bumper (747.8): 239.5 px
The length less the standard bumper's; the photo's own reading agrees within its ±.
The pin across the body and the bumper: its centre ahead of the body's open end0.144 in ± 0.02 in 3.7 mmProvisionalPhoto: BCM's photo of the T0 standing upright, 1920 x 1281
Photo 0.144 in ± 0.02 in used
BCM's photo of the T0 standing upright, 1920 x 1281, harvested
Scale: the body's own width, 167 px, as the standard's 0.687 (std.carbine_buffer.body_d). Read by the pin hole's centre (y 293) below the body's top end (258): 35 px
The kit photo (da2d35d9e02d) has it 9.4 px from the bumper, 0.142 in. The standard carbine buffer's pin is 0.24 in from its open end (std.carbine_buffer.pin_from_open_end): BCM's bumper is "Modified to fit Pre-load Spring".
The pin across the body: its diameter0.09 in ± 0.02 in 2.3 mmProvisionalPhoto: BCM's photo of the T0 standing upright, 1920 x 1281
Photo 0.09 in ± 0.02 in used
BCM's photo of the T0 standing upright, 1920 x 1281, harvested
Scale: the body's own width, 167 px, as the standard's 0.687. Read by the pin hole's dark ring, 22 px across
Smaller than the standard buffer's .122 pin.
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Receiver extension bore
- Receiver extensions
- BCM Milspec Carbine Receiver Extension (Buffer Tube) 6 Position, BCM MK2 Receiver Extension, Geissele Automatics Premium Mil-Spec Buffer Tube, Guntec USA AR-15 Mil-Spec Buffer Tube (Gen 2), SB Tactical SBPDW receiver extension, housing and integral castle nut, VLTOR RE-A5 7-Position Receiver Extension, MilSpec Diameter
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- BCM $36.95 Nov 21, 2026, in stock that day