End plate
VLTOR Receiver Extension End Plate
The plate between the castle nut and the lower receiver: a ring round the receiver extension with a lobe that covers the takedown pin's detent spring, a key in its hole that rides in the extension's slot, a boss on its front face and the dimple behind it, VLTOR's V in the dimple. VLTOR: "Mil-Spec Receiver Extension End Plate" (sold alone, V2-1069-M1). Its A5 kits list it as "(1) Vltor Lockplate" ("(1) RE-A5 Receiver Extension (1) A5H2 Buffer (1) A5 Buffer Spring (1) Vltor Lockplate (1) Vltor Castle Nut"); the SP-A5's short description calls it the "End Plate".

- Weight
- 0.55 oz ± 0.03 oz Provisionalworked out: ({.face_area} - 0.785398163 * {.hole_d} * {.hole_d}) * {.thickness} * {std.density.steel}
- Lowest price
- $5.95 at VLTOR, read Nov 21, 2026
- Maker's number
- V2-1069-M1
- Colour
- Phosphate, black
- Drawn as
- modelled
- Maker's page
- vltor.com
In “Two-tone 16 in, Stealth Gray and soft-shooting”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Thickness0.124 in ± 0.001 in 3.1 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.124 in ± 0.001 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the plate's two faces, planes y 0 and y 0.1240
A mil-spec plate as the reference model has it: Guntec's plate has that plate's outline on three photos (top_above_axis, bottom_below_axis, boss_width).
End plate top above the tube axis (its ring's radius)0.682 in ± 0.001 in 17.3 mmConflictModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.6817 in ± 0.001 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the ring's outer cylinder, r 0.6817 (#899)
Photo 0.72 in ± 0.03 in
VLTOR's picture of its SP-A5 kit: the lockplate lying face on, a little tilted, 1024 x 683; its A5 Buffer Kit picture ba600a518974 has the same cut-out, harvested
Scale: across: the hole's width as a mil-spec plate's (hole_d, 1.1902 in), 127 px: 106.7 px/in; down: the hole's own height, 119 px for the same 1.1902 (the plate is tilted 20 degrees down the picture): 100 px/in. Read by the ring's top edge (row 366) above the hole's middle (row 438, where the hole is widest)
Photo 0.683 in ± 0.01 in
VLTOR's photograph of the plate sold alone, V2-1069-M1, its rear face square on, 1024 x 683, harvested
Scale: its hole as a mil-spec plate's (hole_d, 1.1902 in): 279 px across and 278 down, round to the pixel: 234.4 px/in. Read by the ring's top edge (row 85) above the hole's middle (row 245)
The mil-spec plate's (VLTOR: "Mil-Spec Receiver Extension End Plate"), which VLTOR's own photographs read within their ±.
model and photo differ by 0.038 in beyond what each states it is good to.
End plate lobe bottom below the tube axis1.379 in ± 0.001 in 35 mmConflictModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 1.3788 in ± 0.001 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the lobe's round end, r 0.4266 about a centre 0.9522 below the axis
Photo 1.41 in ± 0.03 in
VLTOR's picture of its SP-A5 kit: the lockplate lying face on, a little tilted, 1024 x 683; its A5 Buffer Kit picture ba600a518974 has the same cut-out, harvested
Scale: across: the hole's width as a mil-spec plate's (hole_d, 1.1902 in), 127 px: 106.7 px/in; down: the hole's own height, 119 px for the same 1.1902 (the plate is tilted 20 degrees down the picture): 100 px/in. Read by the lobe's bottom (row 579) below the hole's middle
Photo 1.391 in ± 0.012 in
VLTOR's photograph of the plate sold alone, V2-1069-M1, its rear face square on, 1024 x 683, harvested
Scale: its hole as a mil-spec plate's (hole_d, 1.1902 in): 279 px across and 278 down, round to the pixel: 234.4 px/in. Read by the lobe's bottom (row 571) below the hole's middle
The mil-spec plate's (VLTOR: "Mil-Spec Receiver Extension End Plate"), which VLTOR's own photographs read within their ±.
model and photo differ by 0.031 in beyond what each states it is good to.
End plate, the radius of its lobe's round end0.427 in ± 0.001 in 10.8 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.4266 in ± 0.001 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the lobe's end cylinder, r 0.4266 (#973)
Redcon1's photo of Guntec's plate has the lobe's widths at three depths (as fractions of its height) 0.01 to 0.03 in over this outline's, after the outline's 0.04 of shadow is taken off: the lower rows, nearer the lens, read larger.
End plate, its lobe's round end's centre below the tube axis0.952 in ± 0.001 in 24.2 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.9522 in ± 0.001 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the lobe's end cylinder's axis (#973)
End plate, its key's width0.125 in ± 0.002 in 3.2 mmConflictModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.125 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the key's side planes, x ±0.0625 (#1108, #1162)
The extension's slot it rides in is as wide (std.receiver_extension.key_slot_width).
Photo 0.1 in ± 0.02 in
VLTOR's picture of its SP-A5 kit: the lockplate lying face on, a little tilted, 1024 x 683; its A5 Buffer Kit picture ba600a518974 has the same cut-out, harvested
Scale: across: the hole's width as a mil-spec plate's (hole_d, 1.1902 in), 127 px: 106.7 px/in; down: the hole's own height, 119 px for the same 1.1902 (the plate is tilted 20 degrees down the picture): 100 px/in. Read by the key standing up into the hole, 11 px across at row 494
Photo 0.115 in ± 0.01 in
VLTOR's photograph of the plate sold alone, V2-1069-M1, its rear face square on, 1024 x 683, harvested
Scale: its hole as a mil-spec plate's (hole_d, 1.1902 in): 279 px across and 278 down, round to the pixel: 234.4 px/in. Read by the key standing up into the hole, 27 px across (rows 385 to 395, 492 to 519)
The mil-spec plate's (VLTOR: "Mil-Spec Receiver Extension End Plate"), which VLTOR's own photographs read within their ±.
model and photo differ by 0.025 in beyond what each states it is good to.
End plate, its key's tip below the tube axis0.562 in ± 0.002 in 14.3 mmConflictModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.5619 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the key's tip plane, z 0.5619 (#1135)
0.012 below the extension's slot floor (std.receiver_extension.key_slot_floor, 0.55): the key stands clear of it.
Photo 0.576 in ± 0.012 in
VLTOR's photograph of the plate sold alone, V2-1069-M1, its rear face square on, 1024 x 683, harvested
Scale: its hole as a mil-spec plate's (hole_d, 1.1902 in): 279 px across and 278 down, round to the pixel: 234.4 px/in. Read by the key's tip at row 380, between the rows without it and with it
The mil-spec plate's (VLTOR: "Mil-Spec Receiver Extension End Plate"), which VLTOR's own photographs read within their ±.
model and product differ by 0.014 in beyond what each states it is good to.
End plate, the V either side of its key: its floor below the tube axis0.657 in ± 0.002 in 16.7 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.6575 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the two sloped planes' lower ends, z 0.6575 (#1054, #1216), where 0.031 in rounds turn them into the key's sides
End plate, the V either side of its key: where its sloped sides end, out from the middle0.112 in ± 0.002 in 2.8 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.1119 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the sloped planes' inner ends, x ±0.1119 (#1054, #1216)
End plate, the V either side of its key: where it leaves the hole's circle, out from the middle0.354 in ± 0.002 in 9 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.354 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the hole's cylinder ends at x ±0.3540, z 0.4784 (#1007), where the sloped planes begin
End plate, the round at the bottom of the V either side of its key, where it turns into the key's side0.031 in ± 0.001 in 0.8 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.031 in ± 0.001 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by two cylinders r 0.031 at x ±0.0935, z 0.6326 (#1081, #1189)
End plate, its lobe's straight sides: how far each leans in from upright13.5° ± 0.05°ProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 13.5 deg ± 0.05 deg used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the side planes' normals (#946, #1000: 0.972, 0.233), whose lean is atan(0.233 / 0.972)
End plate, where each straight side meets the ring: its angle below the level of the tube axis31.3° ± 0.05°ProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 31.33 deg ± 0.05 deg used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the side planes' upper ends, x ±0.5823, 0.3545 below the axis, on the ring's r 0.6817: atan(0.3545 / 0.5823)
End plate, how far its boss stands out of its front face0.065 in ± 0.002 in 1.6 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.0645 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the boss's face, plane y 0.1885 of a plate 0.1240 thick
No photo on file shows Guntec's boss in profile.
The mil-spec plate's stamped boss and dimple, as deep as the reference model has them: VLTOR's photographs show its dimple from behind only, its width and height and place as the mil-spec plate's (pocket_width, pocket_height, boss_below_axis), and no view shows a depth or the front face.
End plate, the dimple in its rear face behind the boss0.063 in ± 0.002 in 1.6 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.063 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by plane y 0.0630; the dimple is the boss's outline 0.005 larger all round
No photo on file shows Guntec's dimple in profile.
The mil-spec plate's stamped boss and dimple, as deep as the reference model has them: VLTOR's photographs show its dimple from behind only, its width and height and place as the mil-spec plate's (pocket_width, pocket_height, boss_below_axis), and no view shows a depth or the front face.
End plate, how much larger all round its dimple is than its boss0.005 in ± 0.001 in 0.1 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.005 in ± 0.001 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the dimple's ends r 0.1925 against the boss's r 0.1875 (#1433, #1223)
The mil-spec plate's stamped boss and dimple, as deep as the reference model has them: VLTOR's photographs show its dimple from behind only, its width and height and place as the mil-spec plate's (pocket_width, pocket_height, boss_below_axis), and no view shows a depth or the front face.
The hole's diameter1.19 in ± 0.002 in 30.2 mmProvisionalWorked out: {std.receiver_extension.end_plate_hole_d}
Worked out 1.1902 in ± 0.002 in used
{std.receiver_extension.end_plate_hole_d}, harvested
A mil-spec plate's hole, as the reference model has it: VLTOR's kit picture is scaled by it (the ring's width then reads 1.368, the reference model's 1.363).
The ring's width across1.378 in ± 0.01 in 35 mmCorroboratedPhoto: VLTOR's photograph of the plate sold alone, V2-1069-M1, its rear face square on, 1024 x 683
Photo 1.368 in ± 0.02 in
VLTOR's picture of its SP-A5 kit: the lockplate lying face on, a little tilted, 1024 x 683; its A5 Buffer Kit picture ba600a518974 has the same cut-out, harvested
Scale: across: the hole's width as a mil-spec plate's (hole_d, 1.1902 in), 127 px: 106.7 px/in; down: the hole's own height, 119 px for the same 1.1902 (the plate is tilted 20 degrees down the picture): 100 px/in. Read by the outline's widest, row 438: 738 to 883 px, 146 px
Photo 1.378 in ± 0.01 in used
VLTOR's photograph of the plate sold alone, V2-1069-M1, its rear face square on, 1024 x 683, harvested
Scale: its hole as a mil-spec plate's (hole_d, 1.1902 in): 279 px across and 278 down, round to the pixel: 234.4 px/in. Read by the outline's widest, rows 235 to 255: 346 to 668 px, 323 px
VLTOR's photograph of the plate sold alone, square on; the kit picture's reading agrees.
A check of the scale on the picture against the reference model's ring (twice top_above_axis).
End plate, its boss side to side0.496 in ± 0.002 in 12.6 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.496 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by an obround: two r 0.1875 ends at x ±0.0605
End plate, its boss top to bottom0.375 in ± 0.002 in 9.5 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.375 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the obround's two ends' diameter
End plate, its boss's middle below the tube's axis0.997 in ± 0.002 in 25.3 mmCorroboratedModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.9974 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the obround's centre
Photo 1.011 in ± 0.015 in
VLTOR's photograph of the plate sold alone, V2-1069-M1, its rear face square on, 1024 x 683, harvested
Scale: its hole as a mil-spec plate's (hole_d, 1.1902 in): 279 px across and 278 down, round to the pixel: 234.4 px/in. Read by the middle of the dimple in the rear face (crop an.plate2, four times): row 481.9, 236.9 px below the hole's middle
Photo 1 in ± 0.03 in
VLTOR's picture of its SP-A5 kit: the plate face on, tilted 20 degrees, 1024 x 683, harvested
Scale: across: the hole's width as a mil-spec plate's, 127 px: 106.7 px/in; down: the hole's own height, 119 px: 100 px/in. Read by the dimple's middle at row 540, 102 px below the hole's middle at row 438
The mil-spec plate's; VLTOR's two photographs put the dimple's middle within their ± of it.
The dimple in the rear face (VLTOR's V is in it), its width across0.506 in ± 0.003 in 12.9 mmProvisionalWorked out: {.boss_width} + 2 * {.dimple_grow}
Worked out 0.506 in ± 0.003 in used
{.boss_width} + 2 * {.dimple_grow}, harvested
Photo 0.49 in ± 0.02 in
VLTOR's photograph of the plate sold alone, V2-1069-M1, its rear face square on, 1024 x 683, harvested
Scale: its hole as a mil-spec plate's (hole_d, 1.1902 in): 279 px across and 278 down, round to the pixel: 234.4 px/in. Read by the dimple's rim across (crop an.plate2, four times): 115 px
The mil-spec plate's dimple; VLTOR's photograph reads it within its ±.
What shows of the boss on the rear face: the mil-spec plate's dimple, as much larger all round than the boss as the reference model has it.
The dimple in the rear face, its height0.385 in ± 0.003 in 9.8 mmProvisionalWorked out: {.boss_height} + 2 * {.dimple_grow}
Worked out 0.385 in ± 0.003 in used
{.boss_height} + 2 * {.dimple_grow}, harvested
Photo 0.4 in ± 0.02 in
VLTOR's photograph of the plate sold alone, V2-1069-M1, its rear face square on, 1024 x 683, harvested
Scale: its hole as a mil-spec plate's (hole_d, 1.1902 in): 279 px across and 278 down, round to the pixel: 234.4 px/in. Read by the dimple's rim down (crop an.plate2, four times): 94 px
The mil-spec plate's dimple; VLTOR's photograph reads it within its ±.
The edges' break0.012 in ± 0.006 in 0.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows its edges in profile. A plate's edges are broken a little, and a sharp edge reads as a line of light in the app.
Worked out 0.012 in ± 0.006 in used
An assumption for the drawing, not a reading: no view on file shows its edges in profile. A plate's edges are broken a little, and a sharp edge reads as a line of light in the app., harvested
Height2.061 in ± 0.002 in 52.3 mmProvisionalWorked out: {.top_above_axis} + {.bottom_below_axis}
Worked out 2.0605 in ± 0.002 in used
{.top_above_axis} + {.bottom_below_axis}, harvested
The face's area, the hole's included2.087 in ± 0.004 in 53 mmProvisionalWorked out: {.top_above_axis} * {.top_above_axis} * (180 + 2 * {.corner_angle}) * 3.14159265 / 360 + {.lobe_radius} * {.lobe_radius} * (180 - 2 * {.side_angle}) * 3.14159265 / 360 + {.lobe_radius} * {.lobe_centre_below_axis} * cos({.side_angle}) + {.top_above_axis} * cos({.corner_angle}) * ({.lobe_centre_below_axis} + {.lobe_radius} * sin({.side_angle})) - {.lobe_radius} * {.top_above_axis} * cos({.side_angle}) * sin({.corner_angle})
Worked out 2.0875 in ± 0.004 in used
{.top_above_axis} * {.top_above_axis} * (180 + 2 * {.corner_angle}) * 3.14159265 / 360 + {.lobe_radius} * {.lobe_radius} * (180 - 2 * {.side_angle}) * 3.14159265 / 360 + {.lobe_radius} * {.lobe_centre_below_axis} * cos({.side_angle}) + {.top_above_axis} * cos({.corner_angle}) * ({.lobe_centre_below_axis} + {.lobe_radius} * sin({.side_angle})) - {.lobe_radius} * {.top_above_axis} * cos({.side_angle}) * sin({.corner_angle}), harvested
Worked out from the outline's figures, for the weight: the ring's arc between its corners, the lobe's end, the two straight sides and what lies between them (as guntec-ar15-end-plate's).
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Receiver extension end
End plate, where the castle nut bears
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- VLTOR $5.95 Nov 21, 2026, in stock that day