Castle nut
Geissele Automatics Premium Mil-Spec Buffer Tube Assembly, castle nut
The nut on the receiver extension's thread that is turned down onto the end plate and locks the extension to the lower receiver, its four wrench notches in its rear face and a staking notch in its front face's edge, in Geissele's Premium Mil-Spec Buffer Tube Assembly. Its sellers: "Included in the package is a high-quality, mil-spec castle nut and end plate" (Mile High Shooting, Midwest Optics, Charlie's Custom Clones). Not sold alone on any page read, and named by none: the name is the catalog's. A buyer of the DDC at Primary Arms (08-162S, 2025-04-22): "the [in]cluded castle nut and end plate is total trash. My set I found pit marks, poor finish, and poor casting": a buyer's word, kept as it was said.

- Weight
- 0.59 oz ± 0.06 oz Provisionalworked out: (0.785398163 * ({.od} * {.od} - {std.receiver_extension.thread_major_d} * {std.receiver_extension.thread_major_d}) * {.thickness} - {.notches} * {.notch_width} * {.notch_depth} * ({.od} - {std.receiver_extension.thread_major_d}) / 2) * {std.density.steel}
- Lowest price
- Sold in the Geissele Automatics Premium AR-15 H1 Buffer Tube Kit With Super 42 - Carbine, not by itself
- Colour
- Manganese phosphate, charcoal
- Drawn as
- modelled
- Maker's page
- charliescustomclones.com
In “22RB .22 LR rifle”, a build on the start page, in place of its BCM Receiver Extension Nut (Castle Nut).
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Outside diameter1.363 in ± 0.001 in 34.6 mmCorroboratedModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 1.363 in ± 0.001 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by one cylinder, r 0.6815
Photo 1.333 in ± 0.04 in
Charlie's Custom Clones' picture of five assemblies under one light, 3300 x 1696: the black one at the bottom, its nut and plate on it, seen from the side, harvested
Scale: the tube's own outside diameter beside it in the same picture, taken as the mil-spec 1.148 (geissele-premium-mil-spec-buffer-tube.tube_od): 208.5 px between rows 1064 and 1272 behind the nut. Read by the nut's silhouette top to bottom, rows 1044 to 1286 (on a 2x crop): 242 px, 1.161 times the tube's
A black tube's edge reads thin and so does the nut's: their ratio is the reading.
A mil-spec nut, as every seller says the assembly's is; the one photo that shows it beside the tube puts it within its ± of the model's.
Thickness0.377 in ± 0.001 in 9.6 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.3765 in ± 0.001 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by its front face to its rear face, planes y 0 and y 0.3765
No photo on file shows the nut square from the side: on the tube in Charlie's picture the tube is turned a little, and the nut's rear face shows as a band beside its side.
Wrench notches in its rear face4ProvisionalPhoto: Primary Arms' 08-162B_03: the black tube with its plate and nut, the nut lying on its front face, seen from above and in front
Photo 4 count used
Primary Arms' 08-162B_03: the black tube with its plate and nut, the nut lying on its front face, seen from above and in front, harvested
Scale: none: a count. Read by counted round the rear face, every quarter turn: one at the top, one each side, one at the near side, the whole ring in view
Charlie's gray assembly (234b20bbfb70) shows the same four.
Wrench notch width0.162 in ± 0.001 in 4.1 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.162 in ± 0.001 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by a wrench notch's two side planes, ±0.0810
Wrench notch depth (into the rear face)0.138 in ± 0.001 in 3.5 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.1375 in ± 0.001 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by a wrench notch's floor plane, y 0.2390 of 0.3765
Staking notches in its front face's outer edge3ProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 3 count used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by three notches 120 degrees apart, counted in the face list (planes #20197, #20323 and their like)
One shows in each photo that sees the front face's edge (the flat lay's near side, under the near wrench notch; the side of the nut on the tube in Charlie's picture): the others are behind. The count is the reference model's.
Staking notch, width0.09 in ± 0.002 in 2.3 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.09 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by a notch's two side planes, ±0.0450
Staking notch, depth into the front face0.082 in ± 0.002 in 2.1 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.082 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by a notch's floor
Staking notch, how far in from the outside it is cut0.075 in ± 0.002 in 1.9 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.075 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the notch's inner wall, a cylinder r 0.6065 of an outside r 0.6815
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.