End plate
Guntec USA AR-15 Receiver End Plate
The plate between the castle nut and the lower receiver: a ring round the receiver extension with a lobe that covers the takedown pin's detent spring, a key in its hole that rides in the extension's slot, and a boss on the lobe. Guntec: "US Made Steel", "Fits Mil-spec/Commercial Buffer Tubes", "Color: Black", "Finish: Nitride", "Material: Steel"; UPC 714569652319. The end plate in Guntec's buffer tube set (The Country Shed, Guntec's words for the set: "Includes End Plate, Castle Nut, 3 oz CAR Buffer, & Upgraded Chrome Silicon Spring"), black in every colour of the set.

- Weight
- 0.55 oz ± 0.02 oz Provisionalworked out: ({.face_area} - 0.785398163 * {.hole_d} * {.hole_d}) * {.thickness} * {std.density.steel}
- Lowest price
- $5.95 at Guntec USA, read Oct 20, 2026
- Maker's number
- ENDPLATE
- Colour
- Black nitride
- Drawn as
- modelled
- Maker's page
- guntecusa.com
In “22RB .22 LR rifle”, a build on the start page, in place of its BCM Receiver End Plate.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Thickness0.124 in ± 0.001 in 3.1 mmCorroboratedModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.124 in ± 0.001 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the plate's two faces, planes y 0 and y 0.1240
A mil-spec plate as the reference model has it: Guntec's plate has that plate's outline on three photos (top_above_axis, bottom_below_axis, boss_width).
Photo 0.11 in ± 0.04 in
Redcon1 Tactical: Guntec's red set laid out, 810 x 690; the plate lying flat, seen from above, harvested
Scale: the hole's width taken as a mil-spec plate's (std.receiver_extension.end_plate_hole_d), 94.7 px/in across; the plate's tilt from its round hole's aspect, 0.73 (the hole's own 0.655 with the wall's thickness seen at its far side added back). Read by the lobe's lit edge at its bottom, rows 641 to 648 at column 409: 7 px, over the cosine of the tilt (0.68)
Two or three pixels: a check, not a size.
No page states it; Guntec's plate has the reference model's outline on three photos, and the one photo that shows its edge agrees within its ±.
A stamped plate: no page states its thickness.
End plate top above the tube axis (its ring's radius)0.682 in ± 0.001 in 17.3 mmCorroboratedModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.6817 in ± 0.001 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the ring's outer cylinder, r 0.6817 (#899)
Photo 0.68 in ± 0.03 in
Guntec: its clear set assembled, MILTUBESET-CLEAR, 900 px; from the user's saved page of the clear tube, 2026-10-19, harvested
Scale: the tube's own outside diameter just behind the nut, where it is the tube alone, taken as std.receiver_extension.milspec_od (1.148): 84.3 px, 73.4 px/in across the axis. Read by the silhouette's reach above the tube's axis where the plate stands (along the axis 80 to 104 px from the reference column), in the frame of the tube's top and bottom edges; the median of those columns
Read across the axis, which a cylinder's silhouette shows whatever the lens's yaw; a flat plate's height reads short by the cosine of how far above or below it the lens stood.
Photo 0.667 in ± 0.03 in
Guntec: its purple set assembled, MILTUBESET-PURPLE_Rev, 900 px; from the user's saved page of the purple tube, 2026-10-19, harvested
Scale: the tube's own outside diameter just behind the nut, taken as std.receiver_extension.milspec_od (1.148): 82.5 px, 71.8 px/in across the axis. Read by as the clear set's: the median reach above the axis along the plate
Photo 0.702 in ± 0.03 in
Guntec: ENDPLATE_2048, its own picture of the plate face on, 2048 px, from its page as the user saved it, 2026-10-20, from the site owner
Scale: down: the picture isn't square on (the hole's ellipse is 0.928 as tall as wide, its turn under 2 degrees): the mean of the hole's own (506 px for its radius) and the ring's (601 px for the 0.69 its width gives), 861 px/in, the plate's edge seen at the tilt shortening the one and lengthening the other; heights from the two ellipses' centres, row 745. Read by the outline's top (row 140) above the hole's centre
Its width across, 2 x 632 px of the ring's ellipse, is 1.379 at 916.6 px/in: the ring's radius 0.690.
The reference model's ring; Guntec's two photos read it within their ±.
End plate lobe bottom below the tube axis1.379 in ± 0.001 in 35 mmConflictModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 1.3788 in ± 0.001 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the lobe's round end, r 0.4266 about a centre 0.9522 below the axis
Photo 1.384 in ± 0.03 in
Redcon1 Tactical: Guntec's red set laid out, 810 x 690; the plate lying flat, seen from above, harvested
Scale: a ratio, needing no scale: the lobe's bottom is 2.03 times as far below the hole's centre as the ring's top is above it, both read down the picture (they are foreshortened alike); times the ring's radius (.top_above_axis). Read by the plate's outline (luminance < 150, largest piece) and its hole's ellipse fitted away from the key: top 50.1 px above the hole's centre, bottom 101.9 px below it
Photo 1.338 in ± 0.03 in
Guntec: its clear set assembled, MILTUBESET-CLEAR, 900 px, harvested
Scale: the tube's own outside diameter, as for top_above_axis (73.4 px/in). Read by the silhouette's greatest reach below the tube's axis where the plate's lobe hangs
Read across the axis: short by the cosine of how far above or below the plate the lens stood. The same photo's top over this bottom is 1.97.
Photo 1.346 in ± 0.03 in
Guntec: its purple set assembled, MILTUBESET-PURPLE_Rev, 900 px, harvested
Scale: the tube's own outside diameter (71.8 px/in). Read by as the clear set's
This photo's bottom over its own top is 2.02, the reference model's ratio (1.3788 over 0.6817): both read short alike, as a lens 12 degrees above or below the plate would read them.
Photo 1.399 in ± 0.04 in
Guntec: ENDPLATE_2048, its own picture of the plate face on, 2048 px, from its page as the user saved it, 2026-10-20, from the site owner
Scale: down: the picture isn't square on (the hole's ellipse is 0.928 as tall as wide, its turn under 2 degrees): the mean of the hole's own (506 px for its radius) and the ring's (601 px for the 0.69 its width gives), 861 px/in, the plate's edge seen at the tilt shortening the one and lengthening the other; heights from the two ellipses' centres, row 745. Read by the outline's bottom (row 1949) below the hole's centre
The edge seen at the tilt is in it, on one side of the plate or the other: a few hundredths.
The reference model's lobe. Redcon1's face-on photo puts the bottom at its ratio to the ring (1.384); Guntec's own two photos read it 0.03 to 0.04 short across the tube's axis, and the purple one its top short alike, which is the lens standing off the plate's plane, not a shorter lobe. Kept as read: the clear photo's is just outside its ±, a conflict said.
model and guntec-clear differ by 0.041 in beyond what each states it is good to.
model and guntec-purple differ by 0.033 in beyond what each states it is good to.
The lobe covers the takedown pin's detent spring.
End plate height (its top to its lobe's bottom)2.061 in ± 0.002 in 52.3 mmProvisionalWorked out: {.top_above_axis} + {.bottom_below_axis}
Worked out 2.0605 in ± 0.002 in used
{.top_above_axis} + {.bottom_below_axis}, harvested
End plate, the radius of its lobe's round end0.427 in ± 0.001 in 10.8 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.4266 in ± 0.001 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the lobe's end cylinder, r 0.4266 (#973)
Redcon1's photo of Guntec's plate has the lobe's widths at three depths (as fractions of its height) 0.01 to 0.03 in over this outline's, after the outline's 0.04 of shadow is taken off: the lower rows, nearer the lens, read larger.
End plate, its lobe's round end's centre below the tube axis0.952 in ± 0.001 in 24.2 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.9522 in ± 0.001 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the lobe's end cylinder's axis (#973)
End plate, its hole for the extension's thread1.19 in ± 0.002 in 30.2 mmProvisionalWorked out: {std.receiver_extension.end_plate_hole_d}
Worked out 1.1902 in ± 0.002 in used
{std.receiver_extension.end_plate_hole_d}, harvested
A mil-spec plate's hole, as the reference model has it: Redcon1's photo is scaled by it (the ring's width then reads 1.405 with 0.04 of the outline's shadow in it, the model's 1.363 and that shadow).
End plate, its key's width0.125 in ± 0.002 in 3.2 mmCorroboratedModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.125 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the key's side planes, x ±0.0625 (#1108, #1162)
The extension's slot it rides in is as wide (std.receiver_extension.key_slot_width).
Photo 0.114 in ± 0.01 in
Guntec: ENDPLATE_2048, its own picture of the plate face on, 2048 px, from its page as the user saved it, 2026-10-20, from the site owner
Scale: across: the hole's width taken as a mil-spec plate's (std.receiver_extension.end_plate_hole_d), its ellipse's across semi-axis 545.5 px: 916.6 px/in. Read by the key across, rows 1230 to 1250 (luminance under 150): 100 to 108 px
The reference model's key, as wide as the extension's slot it rides in; Guntec's picture reads it within its ± (its edges' rounding narrows the silhouette).
End plate, its key's tip below the tube axis0.562 in ± 0.002 in 14.3 mmCorroboratedModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.5619 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the key's tip plane, z 0.5619 (#1135)
0.012 below the extension's slot floor (std.receiver_extension.key_slot_floor, 0.55): the key stands clear of it.
Photo 0.541 in ± 0.03 in
Guntec: ENDPLATE_2048, its own picture of the plate face on, 2048 px, from its page as the user saved it, 2026-10-20, from the site owner
Scale: down: the picture isn't square on (the hole's ellipse is 0.928 as tall as wide, its turn under 2 degrees): the mean of the hole's own (506 px for its radius) and the ring's (601 px for the 0.69 its width gives), 861 px/in, the plate's edge seen at the tilt shortening the one and lengthening the other; heights from the two ellipses' centres, row 745. Read by the key's tip (row 1211) below the hole's centre
The reference model's; Guntec's picture reads it within its ±.
End plate, the V either side of its key: its floor below the tube axis0.657 in ± 0.002 in 16.7 mmCorroboratedModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.6575 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the two sloped planes' lower ends, z 0.6575 (#1054, #1216), where 0.031 in rounds turn them into the key's sides
Photo 0.651 in ± 0.03 in
Guntec: ENDPLATE_2048, its own picture of the plate face on, 2048 px, from its page as the user saved it, 2026-10-20, from the site owner
Scale: down: the picture isn't square on (the hole's ellipse is 0.928 as tall as wide, its turn under 2 degrees): the mean of the hole's own (506 px for its radius) and the ring's (601 px for the 0.69 its width gives), 861 px/in, the plate's edge seen at the tilt shortening the one and lengthening the other; heights from the two ellipses' centres, row 745. Read by the V's lowest either side of the key (row 1305) below the hole's centre
The reference model's; Guntec's picture reads it within its ±.
End plate, the V either side of its key: where its sloped sides end, out from the middle0.112 in ± 0.002 in 2.8 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.1119 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the sloped planes' inner ends, x ±0.1119 (#1054, #1216)
End plate, the V either side of its key: where it leaves the hole's circle, out from the middle0.354 in ± 0.002 in 9 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.354 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the hole's cylinder ends at x ±0.3540, z 0.4784 (#1007), where the sloped planes begin
End plate, the round at the bottom of the V either side of its key, where it turns into the key's side0.031 in ± 0.001 in 0.8 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.031 in ± 0.001 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by two cylinders r 0.031 at x ±0.0935, z 0.6326 (#1081, #1189)
End plate, the break on its edges0.012 in ± 0.006 in 0.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: no view on file shows its edges in profile; the reference model's are sharp. A stamped plate's edges are broken a little, and a sharp edge reads as a line of light in the app.
Worked out 0.012 in ± 0.006 in used
An assumption for the drawing, not a reading: no view on file shows its edges in profile; the reference model's are sharp. A stamped plate's edges are broken a little, and a sharp edge reads as a line of light in the app., harvested
End plate, its boss side to side0.496 in ± 0.002 in 12.6 mmCorroboratedModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.496 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by an obround: two r 0.1875 ends at x ±0.0605
Photo 0.497 in ± 0.02 in
Redcon1 Tactical: Guntec's red set laid out, 810 x 690; the plate lying flat, seen from above, harvested
Scale: the hole's width taken as a mil-spec plate's (std.receiver_extension.end_plate_hole_d): 94.7 px/in across the picture, where the plate isn't foreshortened. Read by row 612 across the obround: its rim's two dark lines at columns 390 and 437, 47 px
Redcon1's chrome set picture (a copy on file, 1215 px) has the same photograph of the plate at 1.5 times the size: its obround reads 0.492 there (row 920, columns 586 and 656, at 142.2 px/in by the hole). Not a second plate.
Photo 0.504 in ± 0.01 in
Guntec: ENDPLATE_2048, its own picture of the plate face on, 2048 px, from its page as the user saved it, 2026-10-20, from the site owner
Scale: across: the hole's width taken as a mil-spec plate's (std.receiver_extension.end_plate_hole_d), its ellipse's across semi-axis 545.5 px: 916.6 px/in. Read by row 1584 across the boss: the dark lines of its edges at columns 825 and 1287, 462 px
Guntec's own obround reads the reference model's width to a thousandth.
End plate, its boss top to bottom0.375 in ± 0.002 in 9.5 mmCorroboratedModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.375 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the obround's two ends' diameter
Photo 0.376 in ± 0.03 in
Redcon1 Tactical: Guntec's red set laid out, 810 x 690; the plate lying flat, seen from above, harvested
Scale: 94.7 px/in across, times the plate's tilt down the picture (0.73, as for thickness). Read by column 409 down the obround: its rim's dark lines at rows 603 and 629, 26 px
Photo 0.409 in ± 0.04 in
Guntec: ENDPLATE_2048, its own picture of the plate face on, 2048 px, from its page as the user saved it, 2026-10-20, from the site owner
Scale: down: the picture isn't square on (the hole's ellipse is 0.928 as tall as wide, its turn under 2 degrees): the mean of the hole's own (506 px for its radius) and the ring's (601 px for the 0.69 its width gives), 861 px/in, the plate's edge seen at the tilt shortening the one and lengthening the other; heights from the two ellipses' centres, row 745. Read by the boss's top and bottom edges, rows 1408 and 1760
Its side, 0.065 proud, shows at the tilt and is in this reading.
Guntec's own obround agrees within its ±.
End plate, its boss's middle below the tube's axis0.997 in ± 0.002 in 25.3 mmCorroboratedModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.9974 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the obround's centre
Photo 1 in ± 0.04 in
Redcon1 Tactical: Guntec's red set laid out, 810 x 690; the plate lying flat, seen from above, harvested
Scale: as for boss_height. Read by the obround's middle (row 616) below the hole's fitted centre (row 546.6): 69.4 px
Photo 0.974 in ± 0.03 in
Guntec: ENDPLATE_2048, its own picture of the plate face on, 2048 px, from its page as the user saved it, 2026-10-20, from the site owner
Scale: down: the picture isn't square on (the hole's ellipse is 0.928 as tall as wide, its turn under 2 degrees): the mean of the hole's own (506 px for its radius) and the ring's (601 px for the 0.69 its width gives), 861 px/in, the plate's edge seen at the tilt shortening the one and lengthening the other; heights from the two ellipses' centres, row 745. Read by the boss's middle (row 1584) below the hole's centre
Guntec's own obround agrees within its ±.
End plate, how far its boss stands out of its front face0.065 in ± 0.002 in 1.6 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.0645 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the boss's face, plane y 0.1885 of a plate 0.1240 thick
No photo on file shows Guntec's boss in profile.
End plate, the dimple in its rear face behind the boss0.063 in ± 0.002 in 1.6 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.063 in ± 0.002 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by plane y 0.0630; the dimple is the boss's outline 0.005 larger all round
No photo on file shows Guntec's dimple in profile.
End plate, how much larger all round its dimple is than its boss0.005 in ± 0.001 in 0.1 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 0.005 in ± 0.001 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the dimple's ends r 0.1925 against the boss's r 0.1875 (#1433, #1223)
End plate, its lobe's straight sides: how far each leans in from upright13.5° ± 0.05°ProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 13.5 deg ± 0.05 deg used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the side planes' normals (#946, #1000: 0.972, 0.233), whose lean is atan(0.233 / 0.972)
Each side is tangent to the lobe's round end and meets the ring's circle at a corner (it isn't tangent to the ring).
End plate, where each straight side meets the ring: its angle below the level of the tube axis31.3° ± 0.05°ProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 31.33 deg ± 0.05 deg used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by the side planes' upper ends, x ±0.5823, 0.3545 below the axis, on the ring's r 0.6817: atan(0.3545 / 0.5823)
End plate, the area its outline holds (the hole not taken out)2.087 in ± 0.004 in 53 mmProvisionalWorked out: {.top_above_axis} * {.top_above_axis} * (180 + 2 * {.corner_angle}) * 3.14159265 / 360 + {.lobe_radius} * {.lobe_radius} * (180 - 2 * {.side_angle}) * 3.14159265 / 360 + {.lobe_radius} * {.lobe_centre_below_axis} * cos({.side_angle}) + {.top_above_axis} * cos({.corner_angle}) * ({.lobe_centre_below_axis} + {.lobe_radius} * sin({.side_angle})) - {.lobe_radius} * {.top_above_axis} * cos({.side_angle}) * sin({.corner_angle})
Worked out 2.0875 in ± 0.004 in used
{.top_above_axis} * {.top_above_axis} * (180 + 2 * {.corner_angle}) * 3.14159265 / 360 + {.lobe_radius} * {.lobe_radius} * (180 - 2 * {.side_angle}) * 3.14159265 / 360 + {.lobe_radius} * {.lobe_centre_below_axis} * cos({.side_angle}) + {.top_above_axis} * cos({.corner_angle}) * ({.lobe_centre_below_axis} + {.lobe_radius} * sin({.side_angle})) - {.lobe_radius} * {.top_above_axis} * cos({.side_angle}) * sin({.corner_angle}), harvested
In square inches, held as a length's number: the ring's arc above the two corners and the lobe's round end below its tangent points, each as a sector about its own centre, and between them the four triangles from the axis to the corners, the tangent points and the lobe's centre.
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Receiver extension end
End plate, where the castle nut bears
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Guntec USA $5.95 Oct 20, 2026, in stock that day