Castle nut
VLTOR Receiver Extension Lock Nut
The nut on the receiver extension's thread that is turned down onto the end plate and locks the extension to the lower receiver, its four notches taking the wrench. VLTOR: "Mil-Spec Receiver Extension Lock Nut (Castle Nut)" (sold alone, V2-1069-M3). Its A5 kits list it as "(1) Vltor Castle Nut" ("(1) RE-A5 Receiver Extension (1) A5H2 Buffer (1) A5 Buffer Spring (1) Vltor Lockplate (1) Vltor Castle Nut").

- Weight
- 0.53 oz ± 0.06 oz Provisionalworked out: (0.785398163 * ({.od} * {.od} - {std.receiver_extension.thread_major_d} * {std.receiver_extension.thread_major_d}) * {.thickness} - 4 * {.notch_width} * {.notch_depth} * ({.od} - {std.receiver_extension.thread_major_d}) / 2) * {std.density.steel}
- Lowest price
- $5.95 at VLTOR, read Nov 21, 2026
- Maker's number
- V2-1069-M3
- Colour
- Phosphate, black
- Drawn as
- modelled
- Maker's page
- vltor.com
In “Two-tone 16 in, Stealth Gray and soft-shooting”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Outside diameter1.363 in ± 0.001 in 34.6 mmProvisionalModel: the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock
Model 1.363 in ± 0.001 in used
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11: a third-party model of a mil-spec rifle with a carbine stock, from the site owner
Read by one cylinder, r 0.6815
A mil-spec nut as the reference model has it: VLTOR's picture has no size of its own, and every reading on it below is scaled by this.
Thickness0.334 in ± 0.03 in 8.5 mmConflictPhoto: VLTOR's picture of its SP-A5 kit: the nut alone from behind and above, 1024 x 683; its A5 Buffer Kit picture ba600a518974 has the same cut-out
Photo 0.334 in ± 0.03 in used
VLTOR's picture of its SP-A5 kit: the nut alone from behind and above, 1024 x 683; its A5 Buffer Kit picture ba600a518974 has the same cut-out, harvested
Scale: the nut's own outside diameter (od, 1.363 in): its outline's width, 141 px (rows 513 to 519, 427 to 567); the rear face's outer ellipse is half as tall as wide (477 to about 547, 70 px), so the picture looks down 30 degrees and the axis is drawn at cos 30 degrees. Read by the side band below the rear face's near rim, at the middle: 547 to 577, 30 px, over cos 30 degrees, 34.6 px: 0.245 of the outside diameter
Model 0.3765 in ± 0.001 in
the AR-15 CAD reference set the user supplied, Deterrence Dispensed V11, from the site owner
Read by its front face to its rear face, planes y 0 and y 0.3765 (as read for guntec-ar15-castle-nut)
A mil-spec nut as the reference model has it.
VLTOR's own nut, by its picture's proportions; the reference model's nut is another maker's, 0.04 thicker.
photo and model differ by 0.042 in beyond what each states it is good to.
Notches on its rear face4CorroboratedPhoto: VLTOR's photograph of the nut sold alone, V2-1069-M3, from its notched face turned about 29 degrees, 1024 x 683
Photo 4 count
VLTOR's kit picture: the nut from behind and above, the whole rim of its rear face in view, harvested
Scale: none: a count. Read by four notches round the rim (crop an.nut, five times): at the far side, at the right, at the front left and at the left; their places on the rear face's ellipse, taken back to a circle, are 92, 94, 85 and 89 degrees apart. No fifth: every stretch of the rim between them is in view.
Photo 4 count used
VLTOR's photograph of the nut sold alone, V2-1069-M3, from its notched face turned about 29 degrees, 1024 x 683, harvested
Scale: none: a count. Read by four notches (crop an.nut2, three times): one through the wall at the right, one through the bore at the far left, two on the near rim between them
Counted on both of VLTOR's pictures: four.
A notch's width0.123 in ± 0.02 in 3.1 mmCorroboratedPhoto: VLTOR's photograph of the nut sold alone, V2-1069-M3, from its notched face turned about 29 degrees, 1024 x 683
Photo 0.12 in ± 0.03 in
a photo on file, harvested
Scale: the outside diameter (od, 1.363 in), 141 px across. Read by the notch at the far side, 12 px across the rim where it runs across the picture (rows 483 to 486, 518 to 529 px); the one at the front left, 12 px where the rim runs at 70 degrees to the picture's rows (13 px along it)
Photo 0.123 in ± 0.02 in used
VLTOR's photograph of the nut sold alone, V2-1069-M3, from its notched face turned about 29 degrees, 1024 x 683, harvested
Scale: the outline's height, the outside diameter seen square (od, 1.363 in): 298 px (rows 175 to 473), 218.6 px/in; across, the ring is drawn 260 px wide, so its face is turned 29 degrees and the axis is drawn at sin 29 degrees. Read by the notch through the wall at the right, along the outline's height where it runs up the picture: 27 px
VLTOR's photograph of the nut alone; the kit picture's reading agrees.
A notch's depth (into the rear face)0.112 in ± 0.03 in 2.8 mmCorroboratedPhoto: VLTOR's photograph of the nut sold alone, V2-1069-M3, from its notched face turned about 29 degrees, 1024 x 683
Photo 0.134 in ± 0.03 in
a photo on file, harvested
Scale: the outside diameter (od, 1.363 in), 141 px across; the axis drawn at cos 30 degrees (thickness). Read by the front-left notch's floor 12 px under the rim on a crop at five times (an.nut), over cos 30 degrees
Photo 0.112 in ± 0.03 in used
VLTOR's photograph of the nut sold alone, V2-1069-M3, from its notched face turned about 29 degrees, 1024 x 683, harvested
Scale: the outline's height, the outside diameter seen square (od, 1.363 in): 298 px (rows 175 to 473), 218.6 px/in; across, the ring is drawn 260 px wide, so its face is turned 29 degrees and the axis is drawn at sin 29 degrees. Read by the notch through the wall at the right, its floor 12 px in from the rim across the picture, over sin 29 degrees
VLTOR's photograph of the nut alone; the kit picture's reading agrees within the ± of both.
The edges' break0.012 in ± 0.006 in 0.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: the picture shows the rear face's edges a little rounded where the light catches them; how much isn't read.
Worked out 0.012 in ± 0.006 in used
An assumption for the drawing, not a reading: the picture shows the rear face's edges a little rounded where the light catches them; how much isn't read., harvested
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
End plate, where the castle nut bears
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- VLTOR $5.95 Nov 21, 2026, in stock that day