Stock
BCM Stock - Mod 0
BCM's minimalist carbine stock ("The strongest light-weight polymer stock available for your mil-spec receiver extension"): a slim cheek round the tube with a large lever under it, a rear body with an ambidextrous QD socket and a web sling slot, a rubber butt pad. Six positions on a mil-spec receiver extension only. BCM states no size or weight; a seller gives 6.75 x 4.9 x 1.67 in (by BCM's patent section and its photo of the stock on a rifle it is 6.66 in long), sellers 8.2 to 8.4 oz.

- Weight
- 8.2 oz Conflictpublished: Primary Arms, BCM-GFS-MOD-0-BLK (specification table; its feature list says "8.2 oz weight"), a seller, read Oct 5, 2026Its sources span 7.45 oz to 8.45 oz.
- Lowest price
- $55.89 at Impact Guns, read Nov 21, 2026 (Black)
- Maker's number
- BCM-GFS-MOD-0-BLK
- Colours
- Black, Flat Dark Earth, Foliage Green, Wolf Gray
- Drawn as
- modelled
- Maker's page
- bravocompanyusa.com
In “BCM 16 in mid-length”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Overall length6.657 in ± 0.04 in 169.1 mmConflictPhoto: US 9,109,855 B1, Bravo Company USA, sheet 4 of 7: FIG. 4A, sectional side view of the stock on a receiver extension
Published “Length: 6.75"”
Wing Tactical, Bravo Company BCMGUNFIGHTER MOD 0 Stock (Specifications), a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
The seller's figure; how it was taken isn't said.
Photo 6.657 in ± 0.04 in used
US 9,109,855 B1, Bravo Company USA, sheet 4 of 7: FIG. 4A, sectional side view of the stock on a receiver extension, harvested
Scale: the receiver extension drawn in the stock: its outer limbs at rows 550.5 and 725.5 (column 1300), 175 px for std.receiver_extension.milspec_od = 1.148 in: 152.4 px/in. The tube's position pockets repeat every 99.3 px there, 0.652 in (the standard's step is 0.66). Read by the stock's front face (column 1397.5) to the butt pad's rearmost point (column 2412): 1014.5 px; ± for the strokes (a pixel on the tube's 175)
Photo 6.637 in ± 0.05 in
BCM, MOD 0 STOCK SERIES brochure, page 3: a rifle with the Flat Dark Earth stock, straight right side, 1280 x 800, harvested
Scale: frame from the receiver's pins on its right side: the selector (437.4, 403.6), the trigger pin (475.3, 410.2) and the hammer pin (503.7, 400.1) stand 33.69 px/in apart by std.ar15.selector_x, trigger_pin_x and hammer_pin_x (the three pairs agree to 0.01) and put the takedown pin at column 410.35; the pivot pin's head is at 625.5 by eye, 625.1 by that frame; the pins' heights agree with the standard within a pixel. Read by the butt's rearmost point (column 37.5, rows 348 to 356, at the 50% level against the dark ground) to the cheek's front face against the black tube (column 261.1, rows 348 to 372): 223.6 px; ± for the two edges and the scale
BCM's own section drawing, at the scale of the mil-spec tube it is drawn on, and BCM's own photo of the stock on a rifle, at the scale of the receiver's pins, agree within 0.02 in. The seller's 6.75 is 1.4% over both and isn't explained (its height and width agree with the drawing).
wing and patent differ by 0.093 in beyond what each states it is good to.
wing and installed-rifle differ by 0.113 in beyond what each states it is good to.
The one published figure, a seller's, is 0.09 in over two measurements that agree: BCM's patent section at the scale of the tube drawn in it, and BCM's photo of the stock on a rifle at the scale of the receiver's pins. The same seller's height and width agree with the patent within 0.2%. The seller's straight side photo reads longer still against its height (1709 x 1227 px: 6.82 in for 4.9): its ends are the stock's near edges, which stand nearer the lens than the top and the toe.
Height4.9 in 124.5 mmCorroboratedPublished: Wing Tactical, Bravo Company BCMGUNFIGHTER MOD 0 Stock (Specifications), a seller, read Oct 5, 2026
Published “Height: 4.9"” used
Wing Tactical, Bravo Company BCMGUNFIGHTER MOD 0 Stock (Specifications), a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “The buttpad is small, only 5 inches, and that makes it fast to shoulder even when wearing a heavy jacket.”
Guns America Digest, AR Stock Hack: Magpul CTR vs. BCM Gunfighter Mod 0 (Robert Sadowski, 2024-04-13), a review, read Oct 5, 2026 the page, harvested Oct 5, 2026
The butt pad runs the stock's whole height. The article doesn't say how it was measured.
Photo 4.91 in ± 0.07 in
US 9,109,855 B1, sheet 4 of 7: FIG. 4A, sectional side view, harvested
Scale: the receiver extension drawn in the stock, 175 px for std.receiver_extension.milspec_od = 1.148 in: 152.4 px/in. Read by the rear body's top (row 529.5 at column 2330: it stands 10 px above the cheek's top, row 539.5) to the toe's underside (row 1277.5 at columns 2290 to 2310): 748 px
A published figure; a reviewer's rounder one and the patent's section scaled by its own tube agree with it.
Width1.67 in 42.4 mmCorroboratedPublished: Wing Tactical, Bravo Company BCMGUNFIGHTER MOD 0 Stock (Specifications), a seller, read Oct 5, 2026
Published “Width: 1.67"” used
Wing Tactical, Bravo Company BCMGUNFIGHTER MOD 0 Stock (Specifications), a seller, read Oct 5, 2026 the page, harvested Oct 5, 2026
Published “The comb is 1.7 inches wide and smooth.”
Guns America Digest, AR Stock Hack: Magpul CTR vs. BCM Gunfighter Mod 0 (Robert Sadowski, 2024-04-13), a review, read Oct 5, 2026 the page, harvested Oct 5, 2026
The finer of two published figures that agree: the reviewer's rounds to it. It is the width across the rear body's side wings: the patent's rear view (FIG. 3B), scaled by the height, is 1.67 in across them and narrower across the body (body_width).
Width of the body: the cheek round the tube, the lever under it and the butt1.462 in ± 0.02 in 37.1 mmProvisionalPhoto: US 9,109,855 B1 (Bravo Company USA), FIG. 3B rear view, sheet 3 of 7
Photo 1.462 in ± 0.02 in used
US 9,109,855 B1 (Bravo Company USA), FIG. 3B rear view, sheet 3 of 7, harvested
Scale: scale from bcm-stock-mod-0.height = 4.9 in (y-extent 848 px → 173.1 px/in). Read by width of the traced outline (tools/trace.py); the outline's width with the two ears (the rear body's side wings) left out: the body's sides
The published width is across the rear body's two side wings, which lap over the main body's sides and stand proud of them. The patent's rear view shows both: the wings as ears either side of the outline, 0.66 to 1.59 in below the top.
Tube axis below the stock's top edge (at its highest: the rear body's top)0.712 in ± 0.02 in 18.1 mmProvisionalPhoto: US 9,109,855 B1, sheet 4 of 7: FIG. 4A, sectional side view of the stock on a receiver extension
Photo 0.712 in ± 0.02 in used
US 9,109,855 B1, sheet 4 of 7: FIG. 4A, sectional side view of the stock on a receiver extension, harvested
Scale: the receiver extension drawn in the stock, 175 px between its outer limbs for std.receiver_extension.milspec_od = 1.148 in: 152.4 px/in; the stock's length and height read 6.66 and 4.91 in at that scale against Wing's 6.75 and 4.9. Read by the tube's axis, midway between its outer limbs (rows 550.5 and 725.5 at column 1300: row 638.0), below the rear body's top (row 529.5 at column 2330): 108.5 px; ± for the strokes (2 px) and the scale
The rear body's top stands 0.066 in above the cheek's (10 px in the patent's section; the side photo shows the same step, 15 px at 250 px/in). Below the cheek's own top the axis is 0.646 in: the tube's radius and a wall 0.07 in thick, which is how the bore shows in Wing's photo of the stock from the front, all but touching the top.
The bore for the receiver extension: its depth from the stock's front face5.89 in ± 0.06 in 149.6 mmProvisionalPhoto: US 9,109,855 B1, sheet 4 of 7: FIG. 4A, sectional side view
Photo 5.89 in ± 0.06 in used
US 9,109,855 B1, sheet 4 of 7: FIG. 4A, sectional side view, harvested
Scale: the receiver extension drawn in the stock, 175 px for std.receiver_extension.milspec_od = 1.148 in: 152.4 px/in. Read by the stock's front face (column 1397.5) to the tube's rear face against the body's end wall (column 2295): 897.5 px
Collapsed, the tube's rear face stands against the main body's end wall (the section draws it so, the lock pin in the tube's front pocket). Recorded for the record: the model places the end wall from the butt (butt_behind_tube_rear_pos1), which is where the tube's rear face has to arrive.
Butt (the pad's rearmost point) behind the receiver extension's rear face, collapsed0.768 in ± 0.03 in 19.5 mmProvisionalPhoto: US 9,109,855 B1, sheet 4 of 7: FIG. 4A, sectional side view: the lock pin 145 in the tube's front pocket, five pockets 160 behind it
Photo 0.768 in ± 0.03 in used
US 9,109,855 B1, sheet 4 of 7: FIG. 4A, sectional side view: the lock pin 145 in the tube's front pocket, five pockets 160 behind it, harvested
Scale: the receiver extension drawn in the stock, 175 px for std.receiver_extension.milspec_od = 1.148 in: 152.4 px/in. Read by the tube's rear face (column 2295, rows 640 and 700) to the pad's rearmost point (column 2412, rows 580 to 600): 117 px
Lock pin behind the stock's front face2.287 in ± 0.04 in 58.1 mmProvisionalPhoto: US 9,109,855 B1, sheet 4 of 7: FIG. 4A, sectional side view
Photo 2.287 in ± 0.04 in used
US 9,109,855 B1, sheet 4 of 7: FIG. 4A, sectional side view, harvested
Scale: the receiver extension drawn in the stock, 175 px for std.receiver_extension.milspec_od = 1.148 in: 152.4 px/in. Read by the shaft 145 in the tube's front pocket (its sides at columns 1722 and 1770: 0.31 in across, the pockets' own width) centred 348.5 px behind the stock's front face (column 1397.5); the five pockets behind it are centred 99.3 px apart from 1844
The steel block the lever draws down out of the receiver extension's pockets (the patent's locking block 135 and its shaft 145). Where it stands says which pocket the stock is on.
Butt behind the takedown pin at position 1 (collapsed), on a carbine receiver extension8.427 in ± 0.07 in 214 mmConflictWorked out: {.butt_behind_pin_pos5} - 4 * {bcm-receiver-extension.position_step}
Worked out 8.427 in ± 0.07 in used
{.butt_behind_pin_pos5} - 4 * {bcm-receiver-extension.position_step}, harvested
BCM's photo of it on a rifle, four steps out, less the four steps. ± is the photo's.
Worked out 8.46 in ± 0.12 in
{bcm-castle-nut.rear_face_behind_pin} + {.front_behind_nut_pos3} - 2 * {bcm-receiver-extension.position_step} + {.length}, harvested
Wing's photo of it on a lower, two steps out, less the two steps. ± is the photo's and the castle nut's place.
Worked out 8.476 in ± 0.12 in
{magpul-ctr.butt_behind_pin_pos1} - ({.review_ctr_lop_collapsed} - {.lop_collapsed}), harvested
One reviewer's collapsed lengths of pull for the CTR and for this stock, taken off the CTR's measured seat. ± is that seat's, and two figures of unstated method.
Worked out 8.549 in ± 0.1 in
{bcm-receiver-extension.tube_front_behind_pin} + {bcm-receiver-extension.tube_length} - {bcm-receiver-extension.position_hole_rear_from_rear} - 5 * {bcm-receiver-extension.position_step} - {.lock_pin_behind_front} + {.length}, harvested
The lock pin (on the patent's section) in the tube's front hole. ± for the hole's place (0.03), the tube's seat (0.02), the pin's place in a drawing that isn't held to scale (0.04) and the tube's length, which is a generic figure.
Worked out 8.687 in ± 0.1 in
{bcm-receiver-extension.tube_front_behind_pin} + {bcm-receiver-extension.tube_length} + {.butt_behind_tube_rear_pos1}, harvested
The tube's rear face against the stock's end wall, as the section draws it collapsed. ± for the tube's length (generic) and the drawing.
Measured on a photo of the stock on a rifle between the receiver's pins. A second photo, on another lower, and a reviewer's lengths of pull agree within 0.05 in; the lock pin in the tube's front hole within the two ±. The tube's rear end against the stock's end wall, read on the patent's section with a generic tube's length, is 0.26 in more and stays in view.
installed-rifle and tube-rear differ by 0.26 in beyond what each states it is good to.
installed and tube-rear differ by 0.227 in beyond what each states it is good to.
Five ways to it. BCM's brochure has the stock on a rifle from the side, four steps out, with the receiver's pins in view: that is the seat, less the four steps. Wing's close photo of it on a lower, two steps out, by the tube that shows between the stock and the castle nut, agrees within 0.04 in; so does a reviewer's pair of lengths of pull for this stock and the Magpul CTR, whose seat is measured. Two more go through BCM's patent section, which draws the stock collapsed: the lock pin in the tube's front pocket (0.12 in more) and the tube's rear face against the stock's end wall (0.26 in more, outside the two ±): both rest on a generic tube's length and holes and on a drawing that isn't held to scale. Collapsed, the stock's front stands 0.10 in behind the castle nut (bcm-castle-nut.rear_face_behind_pin), clear of it.
Butt behind the takedown pin as BCM photographed it: four steps out (position 5)11.067 in ± 0.06 in 281.1 mmProvisionalPhoto: BCM, MOD 0 STOCK SERIES brochure, page 3: a rifle with the Flat Dark Earth stock, straight right side, 1280 x 800
Photo 11.067 in ± 0.06 in used
BCM, MOD 0 STOCK SERIES brochure, page 3: a rifle with the Flat Dark Earth stock, straight right side, 1280 x 800, harvested
Scale: frame from the receiver's pins on its right side: the selector (437.4, 403.6), the trigger pin (475.3, 410.2) and the hammer pin (503.7, 400.1) stand 33.69 px/in apart by std.ar15.selector_x, trigger_pin_x and hammer_pin_x (the three pairs agree to 0.01) and put the takedown pin at column 410.35; the pivot pin's head is at 625.5 by eye, 625.1 by that frame; the pins' heights agree with the standard within a pixel. Read by the butt's rearmost point (column 37.5, rows 348 to 356, at the 50% level against the dark ground) behind the takedown pin's column (410.35): 372.85 px; the rifle lies level within half a degree (the stock's top edge, the pins); ± for the edge, the pin's column and the scale (0.15 px/in)
Which position it is in: its front face stands 2.76 in behind the castle nut's place, and a stock can't pass the nut, so it is at most four steps out (4 x 0.66); three steps would leave the collapsed stock 0.78 in short of the nut, where Wing's photo, the lock pin and the reviewer's length of pull all have it within 0.25.
The Magpul CTR's collapsed length of pull in the review that gives this stock's10.5 in 266.7 mmProvisionalPublished: Guns America Digest, AR Stock Hack: Magpul CTR vs. BCM Gunfighter Mod 0 (Robert Sadowski, 2024-04-13), a review, read Oct 5, 2026
Published “There is 3.3 inches of adjustment and the LOP ranges from 13.8 inches fully extended to 10.5 inches collapsed.” used
Guns America Digest, AR Stock Hack: Magpul CTR vs. BCM Gunfighter Mod 0 (Robert Sadowski, 2024-04-13), a review, read Oct 5, 2026 the page, harvested Oct 5, 2026
Not this stock's: the same reviewer's figure for the CTR, kept to set his two against each other (butt_behind_pin_pos1, from-ctr). It is the figure retailers carry for the CTR.
The stock's front face behind the castle nut's rear face as Wing photographed it: two steps out (position 3)1.455 in ± 0.1 in 37 mmProvisionalPhoto: Wing Tactical, image 6: the black stock on a lower, right side, 1280 x 1280; the rifle is turned 19 degrees in the picture and seen from a little ahead
Photo 1.455 in ± 0.1 in used
Wing Tactical, image 6: the black stock on a lower, right side, 1280 x 1280; the rifle is turned 19 degrees in the picture and seen from a little ahead, harvested
Scale: the stock's own length along the tube's direction (the cheek's top edge, 19.3 degrees from level): 492 px from the butt's heel (97, 765) to the cheek's top front corner (566, 611) for bcm-stock-mod-0.length = 6.657 in: 73.9 px/in. Seen from 15 degrees ahead the heel's near edge would stand 0.2 in further back and the scale be 71.8. Read by along that direction, from the cheek's top front corner (566, 611) to the castle nut's rear face at its top (667, 574): 107.5 px, 1.455 in (1.50 at the other scale); ± for the two edges, 3 px each, and for the view
Which position it is in: collapsed, the stock's front can't be inside the nut, so the 1.46 in of tube is at most two steps (2 x 0.66); one step would leave the collapsed stock 0.8 in short of the nut, where BCM's own photo of it on a rifle has it 0.1.
Length of pull, collapsed (a reviewer's rifle)10.25 in 260.3 mmProvisionalPublished: Guns America Digest, AR Stock Hack: Magpul CTR vs. BCM Gunfighter Mod 0 (Robert Sadowski, 2024-04-13), a review, read Oct 5, 2026
Published “Fully collapsed the LOP is 10.25 inches; fully extended it is 13.5 inches.” used
Guns America Digest, AR Stock Hack: Magpul CTR vs. BCM Gunfighter Mod 0 (Robert Sadowski, 2024-04-13), a review, read Oct 5, 2026 the page, harvested Oct 5, 2026
BCM states none. A reviewer's figure on his own rifle; how it was taken isn't said. It is 1.82 in more than the seat (butt_behind_pin_pos1), where Magpul's for the MOE Carbine is 1.60 over its own: lengths of pull aren't taken one way, which is why only this reviewer's two figures are set against each other.
Length of pull, extended (a reviewer's rifle)13.5 in 342.9 mmProvisionalPublished: Guns America Digest, AR Stock Hack: Magpul CTR vs. BCM Gunfighter Mod 0 (Robert Sadowski, 2024-04-13), a review, read Oct 5, 2026
Published “Fully collapsed the LOP is 10.25 inches; fully extended it is 13.5 inches.” used
Guns America Digest, AR Stock Hack: Magpul CTR vs. BCM Gunfighter Mod 0 (Robert Sadowski, 2024-04-13), a review, read Oct 5, 2026 the page, harvested Oct 5, 2026
With the collapsed figure: 3.25 in over five steps, 0.65 in a step (bcm-receiver-extension.position_step is 0.66).
The ribs across the strut's underside: their pitch along the strut0.067 in ± 0.002 in 1.7 mmProvisionalPhoto: Primary Arms BCM-GFS-MOD-0-BLK_00.jpg, straight right side on white, 2000 x 1333
Photo 0.0671 in ± 0.002 in used
Primary Arms BCM-GFS-MOD-0-BLK_00.jpg, straight right side on white, 2000 x 1333, harvested
Scale: the trace's scale, 250.4 px/in (bcm-stock-mod-0.height on the outline). Read by the strut's lower edge over rows 815 to 1130 (the part's last dark pixel in each row, to the 50% level), its teeth read off a fitted line: the period of their autocorrelation, 16.81 px (0.84 at that lag; 18 teeth)
The ribs across the strut's underside: how deep the grooves between them are0.013 in ± 0.006 in 0.3 mmProvisionalPhoto: Primary Arms BCM-GFS-MOD-0-BLK_00.jpg, straight right side on white, 2000 x 1333
Photo 0.0133 in ± 0.006 in used
Primary Arms BCM-GFS-MOD-0-BLK_00.jpg, straight right side on white, 2000 x 1333, harvested
Scale: the trace's scale, 250.4 px/in. Read by the same edge, detrended: peak to valley over each period, median 3.3 px
As the silhouette shows them at 250 px/in: a groove narrower than a pixel or two reads shallower than it is.
The butt pad's chevron ribs: their pitch down the pad's height0.115 in ± 0.003 in 2.9 mmConflictPhoto: Primary Arms BCM-GFS-MOD-0-BLK_00.jpg, straight right side on white, 2000 x 1333
Photo 0.115 in ± 0.003 in used
Primary Arms BCM-GFS-MOD-0-BLK_00.jpg, straight right side on white, 2000 x 1333, harvested
Scale: the trace's scale, 250.4 px/in. Read by the pad's rear edge over rows 500 to 1230 (the first dark pixel in each row), its teeth read off a fitted line 6.9 degrees from upright: period 29.0 px along it (autocorrelation 0.79; 23 teeth), 28.8 px of height
Photo 0.1239 in ± 0.003 in
US 9,109,855 B1, sheet 3 of 7: FIG. 3B, rear view, harvested
Scale: the figure's height = bcm-stock-mod-0.height = 4.9 in: 173.1 px/in. Read by the ribs' pairs of lines down column 2408, beside the centre line, from row 1081 to row 1552: 22 periods of 21.45 px
The product's own photo. The patent's figure, which isn't held to scale, draws them 8% further apart.
photo and patent differ by 0.009 in beyond what each states it is good to.
The pad's face is ribbed in chevrons under a star (the patent's rear view, FIG. 3B; BCM's and Wing's photos of the pad).
The butt pad's chevron ribs: how far they stand out of the grooves between them0.011 in ± 0.006 in 0.3 mmCorroboratedPhoto: Primary Arms BCM-GFS-MOD-0-BLK_00.jpg, straight right side on white, 2000 x 1333
Photo 0.0113 in ± 0.006 in used
Primary Arms BCM-GFS-MOD-0-BLK_00.jpg, straight right side on white, 2000 x 1333, harvested
Scale: the trace's scale, 250.4 px/in. Read by the pad's rear edge, detrended: peak to valley over each period, median 2.8 px
Photo 0.0105 in ± 0.007 in
US 9,109,855 B1, sheet 4 of 7: FIG. 4A, sectional side view, harvested
Scale: the receiver extension drawn in the stock: 152.4 px/in. Read by the pad's rear edge in the section over rows 700 to 1230 (the last dark pixel in each row), detrended: peak to valley 1.6 px
The product's own photo; the patent's section reads the same within a tenth of it.
Both readings are of an edge: a rib's rounded end at the pad's side in the photo, a stroke two pixels wide in the patent's section. The ribs may stand higher at the middle of the face.
The butt pad's chevron ribs: how steeply each falls from the centre line to the pad's sides36.5° ± 1.5°ProvisionalPhoto: US 9,109,855 B1, sheet 3 of 7: FIG. 3B, rear view
Photo 36.5 deg ± 1.5 deg used
US 9,109,855 B1, sheet 3 of 7: FIG. 3B, rear view, harvested
Scale: an angle: no scale. Read by the same rib line down columns 2408, 2390, 2370 and 2340 (rows 1316, 1329.5, 1344, 1366.5): 13.5 px over 18, 14.5 over 20, 22.5 over 30
Each rib is an inverted V: its point up on the pad's centre line, its two arms falling to the sides.
The butt pad's chevron ribs: the first rib's point below the pad's top0.83 in ± 0.03 in 21.1 mmProvisionalPhoto: US 9,109,855 B1, sheet 3 of 7: FIG. 3B, rear view
Photo 0.83 in ± 0.03 in used
US 9,109,855 B1, sheet 3 of 7: FIG. 3B, rear view, harvested
Scale: the figure's height = bcm-stock-mod-0.height = 4.9 in: 173.1 px/in. Read by the first pair of rib lines on the centre line under the star (row 1081) below the outline's top (row 937): 144 px
Above it the pad's face carries BCM's star, which isn't drawn.
The rear body's side wings: where each begins to stand out of the body's side, below the stock's top0.649 in ± 0.025 in 16.5 mmCorroboratedPhoto: Primary Arms BCM-GFS-MOD-0-BLK_00.jpg, straight right side on white, 2000 x 1333
Photo 0.649 in ± 0.025 in used
Primary Arms BCM-GFS-MOD-0-BLK_00.jpg, straight right side on white, 2000 x 1333, harvested
Scale: the side profile's own scale: bcm-stock-mod-0.height = 4.9 in over 1227 px, 250.4 px/in. Read by the wing's upper edge, a line along the rear body (row 215 in the trace's `wing` outline; 209 to 215 on a gridded crop), below the outline's top (row 52.5): 162.5 px
Photo 0.653 in ± 0.02 in
US 9,109,855 B1, sheet 3 of 7: FIG. 3B, rear view, harvested
Scale: the figure's height = bcm-stock-mod-0.height = 4.9 in: 173.1 px/in. Read by the outermost stroke each side, row by row: the body's sides stand at columns 2284 and 2537 down to row 1050, where both begin to move out: 113 px below the outline's top (row 937)
The product's own photo, where the wing's upper edge is a line; BCM's rear view has the ear begin within 0.004 in of it.
The rear body's side wings: where each stands furthest out, below the stock's top0.976 in ± 0.03 in 24.8 mmProvisionalPhoto: US 9,109,855 B1, sheet 3 of 7: FIG. 3B, rear view
Photo 0.976 in ± 0.03 in used
US 9,109,855 B1, sheet 3 of 7: FIG. 3B, rear view, harvested
Scale: the figure's height = bcm-stock-mod-0.height = 4.9 in: 173.1 px/in. Read by the outermost strokes are furthest apart (columns 2264 and 2556, 20 px outside the body's each side) on rows 1103 to 1109: 169 px below the outline's top (row 937)
How far it stands out there is the published width less the body's (bcm-stock-mod-0.width and .body_width: 0.104 in a side). The figure itself draws 20 px, 0.116 in: it is 293 px over its ears' strokes, 1.69 in, for the published 1.67. Above this height the ear's outline is a quarter round (half of its reach 0.10 in below its beginning, three quarters at 0.17, nine tenths at 0.24: rows 1067, 1079, 1091) and is drawn as one.
The rear body's side wings: where each has eased back into the body's side, below the stock's top1.65 in ± 0.05 in 41.9 mmProvisionalPhoto: US 9,109,855 B1, sheet 3 of 7: FIG. 3B, rear view
Photo 1.65 in ± 0.05 in used
US 9,109,855 B1, sheet 3 of 7: FIG. 3B, rear view, harvested
Scale: the figure's height = bcm-stock-mod-0.height = 4.9 in: 173.1 px/in. Read by the outermost strokes are back on the body's (columns 2283 and 2537) by row 1223, 286 px below the outline's top (row 937); they are 3 px out on row 1212 (1.59 in, the figure in body_width's note) and 4 px out on row 1205
Below its widest the ear's outline comes in nearly straight (17 px out on row 1133, 10 on row 1169, 4 on row 1205) and is drawn straight. The side photo has the wing's lower edge further down, 1.98 in below the top, with its arch over the QD socket: by this figure that edge is no step out of the body but the upper wall of the recessed panel under it, and the photo agrees (the wall's lit band runs round the panel's upper left corner at one width, from under the wing to the band beside the pad). What the figure can't say: below this height the pad is the widest thing in a view from behind, so the rear body's face may go on leaning in behind the pad's outline; a photo from behind the right side (9368820c28c7) has it one surface from the wing down to the panel. The model ends the ease here, at the body's side, and a crease shows there.
The recessed panel round the QD socket: how far its floor lies in from the body's side0.05 in ± 0.03 in 1.3 mmProvisionalWorked out: An assumption for the drawing, not a reading: a recess a page can draw (docs/research/model-detail-pass-2026-10-12.md, item 6: 'Recess depth unsourced'). Its outline is read (the side profile's `qd_panel`).
Worked out 0.05 in ± 0.03 in used
An assumption for the drawing, not a reading: a recess a page can draw (docs/research/model-detail-pass-2026-10-12.md, item 6: 'Recess depth unsourced'). Its outline is read (the side profile's `qd_panel`)., harvested
ASSUMED. No view on file is square across the panel and none has a shadow of known slope in it. The straight side photo (a9e871874f14) shows its walls as lit bands 15 to 26 px across (0.06 to 0.10 in): walls seen that wide in a straight side view lean or are rounded, and their width there says nothing of the depth. Drawn with square walls.
The pocket in the strut's triangle: how far its floor lies in from the body's side, each side0.1 in ± 0.05 in 2.5 mmProvisionalWorked out: An assumption for the drawing, not a reading: twice the QD panel's assumed depth, for a pocket the obliques show deeper. Its outline is read (the side profile's `triangle`).
Worked out 0.1 in ± 0.05 in used
An assumption for the drawing, not a reading: twice the QD panel's assumed depth, for a pocket the obliques show deeper. Its outline is read (the side profile's `triangle`)., harvested
ASSUMED, and likely shallow: BCM's photos of the butt from behind and below (525e4e3ca3a2) and from the front and below (b10b8afd338e) show a pocket that looks deeper than the panel round the QD socket, with a thin web between the two sides; neither is measured (no camera is fitted to them). In the straight side photo its rear wall's band is 22 px across where the QD panel's is 26, its strut wall's 13. Drawn with square walls, the floor following the body's taper to the toe.
Width of the cheek round the tube (the main body ahead of the rear body), across its sides at the tube's axis1.334 in ± 0.03 in 33.9 mmProvisionalPhoto: Wing Tactical, image 7: the black stock from ahead and to its right, 1280 x 1280
Photo 1.334 in ± 0.03 in used
Wing Tactical, image 7: the black stock from ahead and to its right, 1280 x 1280, harvested
Scale: the bore's mouth in the same face, at std.receiver_extension.milspec_od = 1.148 in: 210 px across along the row through its widest (columns 236 to 446 on row 360, where its edges are steepest). Read by grey levels along row 360 (a band of three): the face's left edge against the ground at column 216.5, the mouth from 236 to 446, the face's right edge, where it turns into the cheek's right side, at 460.5: 244 px of face for 210 of mouth, 1.162 times the tube's diameter; ± for a pixel at each of the four edges and the mouth's clearance
Read on the stock's front face, which the bore's mouth is cut in: the face and the mouth are one plane, so however the face is turned to the lens the two are foreshortened alike, and the face's width over the mouth's, along one row, is the cheek's over the bore's. The mouth is taken at the mil-spec tube's diameter, which the stock is made to take (BCM: 'mil-spec receiver extension'); a mouth a hundredth or two larger makes the cheek as much wider in proportion, inside the ±. In the same photo the face's top stands above the mouth's by 17 px of its 122 px radius, the axis 0.635 in under the top, where the patent's section has 0.646 (tube_axis_below_top less the rear body's step): the check. The rear body behind it, and the butt pad, are body_width (1.46 in).
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Receiver extension (buffer tube)
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Impact Guns $55.89 Black Nov 21, 2026, in stock that day
- BCM $55.95 Black Nov 21, 2026, in stock that day
- BCM $55.95 Flat Dark Earth Nov 21, 2026, in stock that day
- Primary Arms $55.95 Black Nov 21, 2026, in stock that day
- Wing Tactical $55.95 Black Nov 21, 2026, in stock that day
- KYGUNCO $55.95 Black Nov 21, 2026, in stock that day
- T.REX ARMS $55.95 Black Nov 21, 2026, in stock that day
- T.REX ARMS $55.95 Flat Dark Earth Nov 21, 2026, in stock that day
- Dirty Bird Industries $55.95 Flat Dark Earth Nov 21, 2026, in stock that day
- AR15Discounts $55.95 Black Nov 21, 2026, stock not said
- AR15Discounts $55.95 Flat Dark Earth Nov 21, 2026, stock not said
- AR15Discounts $55.95 Foliage Green Nov 21, 2026, stock not said
- AR15Discounts $55.95 Wolf Gray Nov 21, 2026, stock not said
- Alexander's Store $55.95 Black Nov 18, 2026, in stock that day
- Right To Bear $60.00 Black Nov 21, 2026, in stock that day
- Dirty Bird Industries $55.95 Black Nov 21, 2026, out of stock that day
- Dirty Bird Industries $55.95 Foliage Green Nov 21, 2026, out of stock that day
- Dirty Bird Industries $55.95 Wolf Gray Nov 21, 2026, out of stock that day