Buffer
JP Enterprises Silent Captured Spring AR-15 Heavy H3 GEN 2
A buffer and its spring held together on a guide rod as one unit, which takes the place of both in the receiver extension: JP's Silent Captured Spring with its H3 weights, all three tungsten. The maker: "Buffering/Reciprocating Mass: 5.6 oz. (Ideal for replacing a standard buffer of the same weight)", and "The use case for an H3 SCS is virtually the same as the H2. In almost all cases, the two can be used interchangeably, and the choice between the two comes down to a preference in weight and cycling feel. The H2 is will produce a faster, snappier cycle compared to the H3, which will have a slower, heavier cycle. Only in extreme cases such as a severely over-gassed rifle without an adjustable gas block would the H3 be a functional recommendation over the H2."

- Weight
- 7.7 oz ± 0.05 oz Confirmedpublished: JP Enterprises, GEN 2 Silent Captured Spring System for AR-15 type rifle with H3 extra heavy buffer #JPSCS2-15H3 (the maker's store page), the maker, read Oct 18, 2026
- Lowest price
- No price on file
- Maker's number
- JPSCS2-15H3
- Colour
- Black (placeholder)
- Drawn as
- modelled
- Maker's page
- jprifles.com
In “BCM 16 in mid-length”, a build on the start page, in place of its BCM Carbine Buffer.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
The buffer's mass: the slider with its weights, which the carrier drives (what a buffer's class is)5.6 oz ± 0.05 ozConfirmedPublished: JP Enterprises, GEN 2 Silent Captured Spring System for AR-15 type rifle with H3 extra heavy buffer #JPSCS2-15H3 (the maker's store page), the maker, read Oct 18, 2026
Published “Buffering/Reciprocating Mass: 5.6 oz. (Ideal for replacing a standard buffer of the same weight)” used
JP Enterprises, GEN 2 Silent Captured Spring System for AR-15 type rifle with H3 extra heavy buffer #JPSCS2-15H3 (the maker's store page), the maker, read Oct 18, 2026 the page, harvested Oct 18, 2026
JP's FAQ table: "3 Tungsten (H3) 5.6 oz. JPSCS2-15H3". Over the standard's 2.9 oz it is 0.90 oz a tungsten weight; the unit's weight over the standard's, 7.7 against 5.3, is 0.80, as the H2's is.
Of the three weights, how many are tungsten3ConfirmedPublished: JP Enterprises, Buffer Springs and Silent Captured Springs (FAQ: SCS Mass Configuration), the maker, read Oct 18, 2026
Published “3 Tungsten (H3) 5.6 oz. JPSCS2-15H3” used
JP Enterprises, Buffer Springs and Silent Captured Springs (FAQ: SCS Mass Configuration), the maker, read Oct 18, 2026 the page, harvested Oct 18, 2026
Diameter of the slider's front flange (black), the face the carrier bears on0.993 in ± 0.016 in 25.2 mmCorroboratedWorked out: {jp-silent-captured-spring-gen2.flange_d}
Worked out 0.993 in ± 0.016 in used
{jp-silent-captured-spring-gen2.flange_d}, harvested
The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one.
Length of the front flange0.209 in ± 0.01 in 5.3 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.flange_length}
Worked out 0.209 in ± 0.01 in used
{jp-silent-captured-spring-gen2.flange_length}, harvested
The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one.
The round on the flange's front edge0.045 in ± 0.015 in 1.1 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.flange_round}
Worked out 0.045 in ± 0.015 in used
{jp-silent-captured-spring-gen2.flange_round}, harvested
The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one.
Width of each O-ring's band between the flange and a weight and between two weights0.072 in ± 0.016 in 1.8 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.oring_gap}
Worked out 0.072 in ± 0.016 in used
{jp-silent-captured-spring-gen2.oring_gap}, harvested
The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one.
Diameter of the O-rings as they show between the weights0.942 in ± 0.016 in 23.9 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.oring_d}
Worked out 0.942 in ± 0.016 in used
{jp-silent-captured-spring-gen2.oring_d}, harvested
The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one.
Diameter of the three weights (the buffer's widest steel)0.966 in ± 0.016 in 24.5 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.od}
Worked out 0.966 in ± 0.016 in used
{jp-silent-captured-spring-gen2.od}, harvested
The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one.
Length of one weight0.572 in ± 0.01 in 14.5 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.mass_length}
Worked out 0.572 in ± 0.01 in used
{jp-silent-captured-spring-gen2.mass_length}, harvested
The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one.
The break on each weight's edges0.014 in ± 0.007 in 0.4 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.mass_chamfer}
Worked out 0.014 in ± 0.007 in used
{jp-silent-captured-spring-gen2.mass_chamfer}, harvested
The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one.
Weights on the slider3ConfirmedWorked out: {jp-silent-captured-spring-gen2.mass_count}
Worked out 3 count used
{jp-silent-captured-spring-gen2.mass_count}, harvested
The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one.
Width of the snap ring's band behind the rearmost weight0.062 in ± 0.01 in 1.6 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.snap_ring_length}
Worked out 0.062 in ± 0.01 in used
{jp-silent-captured-spring-gen2.snap_ring_length}, harvested
The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one.
Diameter of the snap ring as it shows0.897 in ± 0.025 in 22.8 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.snap_ring_d}
Worked out 0.897 in ± 0.025 in used
{jp-silent-captured-spring-gen2.snap_ring_d}, harvested
The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one.
Diameter of the slider's black rear collar, which the spring bears on0.805 in ± 0.012 in 20.4 mmCorroboratedWorked out: {jp-silent-captured-spring-gen2.collar_d}
Worked out 0.805 in ± 0.012 in used
{jp-silent-captured-spring-gen2.collar_d}, harvested
The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one.
Length of the rear collar0.164 in ± 0.01 in 4.2 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.collar_length}
Worked out 0.164 in ± 0.01 in used
{jp-silent-captured-spring-gen2.collar_length}, harvested
The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one.
Bore of the weights (the slider's tube under them)0.805 in ± 0.012 in 20.4 mmCorroboratedWorked out: {jp-silent-captured-spring-gen2.mass_bore_d}
Worked out 0.805 in ± 0.012 in used
{jp-silent-captured-spring-gen2.mass_bore_d}, harvested
The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one.
Depth of that bore to the screw's head (unit out of the rifle)0.25 in ± 0.1 in 6.3 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.front_bore_depth}
Worked out 0.25 in ± 0.1 in used
{jp-silent-captured-spring-gen2.front_bore_depth}, harvested
The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one.
The slider's inner flange: how thick it is, behind the front bore (the front screw's head bears on it from ahead, the spring from behind)0.1 in ± 0.05 in 2.5 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.inner_flange}
Worked out 0.1 in ± 0.05 in used
{jp-silent-captured-spring-gen2.inner_flange}, harvested
The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one.
Bore through the slider from its rear to its inner flange, which the spring's front end goes into (and the bumper's, which its rear end goes into)0.53 in ± 0.02 in 13.5 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.slider_bore_d}
Worked out 0.53 in ± 0.02 in used
{jp-silent-captured-spring-gen2.slider_bore_d}, harvested
The standard unit's figure: the slider (its flange, tube, collar, O-rings and snap ring, and the weights' shape) are the standard GEN 2's, and no photo of the H3 gives this one.
Length out of the rifle (the slider's front face to the end cap's rear face)7.249 in ± 0.04 in 184.1 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.length}
Worked out 7.249 in ± 0.04 in used
{jp-silent-captured-spring-gen2.length}, harvested
The standard unit's figure: the unit's length, the guide rod and its screws are the standard GEN 2's, and no photo of the H3 gives this one.
The unit's length in the rifle, bolt forward (the slider's front face on the carrier to the extension's rear wall)7.226 in ± 0.03 in 183.5 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.installed_length}
Worked out 7.226 in ± 0.03 in used
{jp-silent-captured-spring-gen2.installed_length}, harvested
The standard unit's figure: the unit's length, the guide rod and its screws are the standard GEN 2's, and no photo of the H3 gives this one.
How far the unit stands out of the extension past the lower's face with the receivers open0.03 in ± 0.015 in 0.8 mmConfirmedWorked out: {jp-silent-captured-spring-gen2.protrusion}
Worked out 0.03 in ± 0.015 in used
{jp-silent-captured-spring-gen2.protrusion}, harvested
The standard unit's figure: the unit's length, the guide rod and its screws are the standard GEN 2's, and no photo of the H3 gives this one.
Diameter of the guide rod (aluminium)0.377 in ± 0.012 in 9.6 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.rod_d}
Worked out 0.377 in ± 0.012 in used
{jp-silent-captured-spring-gen2.rod_d}, harvested
The standard unit's figure: the unit's length, the guide rod and its screws are the standard GEN 2's, and no photo of the H3 gives this one.
The narrowest rear channel of a bolt carrier the guide rod passes into while cycling0.53 in ± 0.0005 in 13.5 mmConfirmedWorked out: {jp-silent-captured-spring-gen2.carrier_channel_min}
Worked out 0.53 in ± 0.0005 in used
{jp-silent-captured-spring-gen2.carrier_channel_min}, harvested
The standard unit's figure: the unit's length, the guide rod and its screws are the standard GEN 2's, and no photo of the H3 gives this one.
The screws' hex socket, across its flats0.125 in ± 0.002 in 3.2 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.hex_socket}
Worked out 0.125 in ± 0.002 in used
{jp-silent-captured-spring-gen2.hex_socket}, harvested
The standard unit's figure: the unit's length, the guide rod and its screws are the standard GEN 2's, and no photo of the H3 gives this one.
Length of the polymer bumper, from the end cap to its front face0.979 in ± 0.012 in 24.9 mmCorroboratedWorked out: {jp-silent-captured-spring-gen2.bumper_length}
Worked out 0.979 in ± 0.012 in used
{jp-silent-captured-spring-gen2.bumper_length}, harvested
The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H3 gives this one.
The bumper's diameter at its front face0.918 in ± 0.016 in 23.3 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.bumper_front_d}
Worked out 0.918 in ± 0.016 in used
{jp-silent-captured-spring-gen2.bumper_front_d}, harvested
The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H3 gives this one.
The bumper's diameter at its rear (it tapers toward the front)0.993 in ± 0.016 in 25.2 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.bumper_rear_d}
Worked out 0.993 in ± 0.016 in used
{jp-silent-captured-spring-gen2.bumper_rear_d}, harvested
The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H3 gives this one.
The round on the bumper's front edge0.06 in ± 0.02 in 1.5 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.bumper_front_round}
Worked out 0.06 in ± 0.02 in used
{jp-silent-captured-spring-gen2.bumper_front_round}, harvested
The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H3 gives this one.
Diameter of the black end cap at the rear0.996 in ± 0.016 in 25.3 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.cap_d}
Worked out 0.996 in ± 0.016 in used
{jp-silent-captured-spring-gen2.cap_d}, harvested
The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H3 gives this one.
Length of the end cap0.116 in ± 0.01 in 2.9 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.cap_length}
Worked out 0.116 in ± 0.01 in used
{jp-silent-captured-spring-gen2.cap_length}, harvested
The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H3 gives this one.
The round on the end cap's rear edge0.035 in ± 0.01 in 0.9 mmCorroboratedWorked out: {jp-silent-captured-spring-gen2.cap_round}
Worked out 0.035 in ± 0.01 in used
{jp-silent-captured-spring-gen2.cap_round}, harvested
The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H3 gives this one.
The end cap's spigot inside the bumper's rear half (its front, which carries the spring's rear end)0.7 in ± 0.08 in 17.8 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.cap_spigot_d}
Worked out 0.7 in ± 0.08 in used
{jp-silent-captured-spring-gen2.cap_spigot_d}, harvested
The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H3 gives this one.
Depth of the end cap's pocket to the screw's head0.05 in ± 0.03 in 1.3 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.pocket_depth}
Worked out 0.05 in ± 0.03 in used
{jp-silent-captured-spring-gen2.pocket_depth}, harvested
The standard unit's figure: the bumper and the end cap are the standard GEN 2's, and no photo of the H3 gives this one.
Diameter of the bore in the slider's front face (the guide rod's screw is at its bottom)0.546 in ± 0.04 in 13.9 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.front_bore_d}
Worked out 0.546 in ± 0.04 in used
{jp-silent-captured-spring-gen2.front_bore_d}, harvested
The standard unit's figure (read there on the H2's photos of the same slider and end cap): no photo of the H3 gives it.
The pocket in the end cap's rear face that the rear screw's head sits in0.42 in ± 0.05 in 10.7 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.cap_pocket_d}
Worked out 0.42 in ± 0.05 in used
{jp-silent-captured-spring-gen2.cap_pocket_d}, harvested
The standard unit's figure (read there on the H2's photos of the same slider and end cap): no photo of the H3 gives it.
The rear screw's head0.36 in ± 0.05 in 9.1 mmProvisionalWorked out: {jp-silent-captured-spring-gen2.screw_head_d}
Worked out 0.36 in ± 0.05 in used
{jp-silent-captured-spring-gen2.screw_head_d}, harvested
The standard unit's figure (read there on the H2's photos of the same slider and end cap): no photo of the H3 gives it.
The spring's outside diameter0.51 in ± 0.015 in 13 mmProvisionalWorked out: {jp-silent-captured-spring-gen2-h2.spring_od}
Worked out 0.51 in ± 0.015 in used
{jp-silent-captured-spring-gen2-h2.spring_od}, harvested
The H2's spring: JP names no spring for the H3, and its only picture of the H3 (a copy on file) is its picture of the H2 (c5a3ef37c597) with the steel weight darkened: the same silhouette to the pixel, the H2's spring in it. JP's use table gives the two one row.
The spring's wire0.047 in ± 0.004 in 1.2 mmProvisionalWorked out: {jp-silent-captured-spring-gen2-h2.wire_d}
Worked out 0.047 in ± 0.004 in used
{jp-silent-captured-spring-gen2-h2.wire_d}, harvested
The H2's spring: JP names no spring for the H3, and its only picture of the H3 (a copy on file) is its picture of the H2 (c5a3ef37c597) with the steel weight darkened: the same silhouette to the pixel, the H2's spring in it. JP's use table gives the two one row.
The spring's turns, end to end25 ± 1ProvisionalWorked out: {jp-silent-captured-spring-gen2-h2.coils}
Worked out 25 count ± 1 count used
{jp-silent-captured-spring-gen2-h2.coils}, harvested
The H2's spring: JP names no spring for the H3, and its only picture of the H3 (a copy on file) is its picture of the H2 (c5a3ef37c597) with the steel weight darkened: the same silhouette to the pixel, the H2's spring in it. JP's use table gives the two one row.
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Receiver extension bore
- Receiver extensions
- BCM Milspec Carbine Receiver Extension (Buffer Tube) 6 Position, BCM MK2 Receiver Extension, Geissele Automatics Premium Mil-Spec Buffer Tube, Guntec USA AR-15 Mil-Spec Buffer Tube (Gen 2), SB Tactical SBPDW receiver extension, housing and integral castle nut, VLTOR RE-A5 7-Position Receiver Extension, MilSpec Diameter