Buffer spring
Guntec USA Upgraded Chrome Silicon Spring
The spring inside the receiver extension, round the buffer, that sends the bolt carrier forward again after each shot: the one in Guntec's mil-spec buffer tube set, and sold only in it. The set's sellers: "Includes End Plate, Castle Nut, 3 oz CAR Buffer, & Upgraded Chrome Silicon Spring" (The Country Shed, MILTUBESET-RED), "The upgraded chrome silicon-coated spring allows for smoother and more efficient cycling" and "Spring Length: 11\" (Carbine)" (Redcon1 Tactical).

- Weight
- 1.98 oz ± 0.13 oz Provisionalworked out: 3.14159265 * ({.od} - {.wire_d}) * {.coils} * 0.785398163 * {.wire_d} * {.wire_d} * {std.density.steel}
- Lowest price
- Sold in the Guntec USA AR-15 Mil-Spec Buffer Tube Set, not by itself
- Colour
- Natural stainless
- Drawn as
- modelled
- Maker's page
- redcon1tactical.com
In “BCM 16 in mid-length”, a build on the start page, in place of its BCM Carbine Action Spring.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Free length11 in ± 0.5 in 279.4 mmConflictPublished: Redcon1 Tactical, Guntec USA AR-15 Mil-Spec Buffer Tube Kit - Anodized Red (MILTUBESET-RED), a seller, read Oct 18, 2026
Published “Spring Length: 11" (Carbine)” used
Redcon1 Tactical, Guntec USA AR-15 Mil-Spec Buffer Tube Kit - Anodized Red (MILTUBESET-RED), a seller, read Oct 18, 2026 the page, harvested Oct 18, 2026
The seller's spec table; its other table has "Buffer Spring Length Carbine Length".
Photo 12.1 in ± 0.1 in
The Country Shed's copy of Guntec's own layout picture of the red set, MILTUBESET-RED, 600 px: the set laid out on white, square on from above; Guntec's page has the picture as MILTUBESET-RED.jpg, uploaded 2019-08, harvested
Scale: the set's tube lying beside it, 278 px for its 7.25 in (guntec-ar15-mil-spec-buffer-tube-gen-2.tube_length): 38.3 px/in; its body's height and its thread's diameter give 38.0 and 38.3. Read by the spring's silhouette end to end along its axis (turned 0.7 degree), 464 to 465 px at three thresholds of darkness
A seller's figure for the set as sold; Guntec's own picture of the spring, laid out beside the tube that scales it, is 1.1 in longer, more than the two ±. The picture is from 2019 (its file's upload on Guntec's page) and may be an earlier spring; the free length isn't drawn (the spring is drawn as installed).
redcon1 and layout differ by 1.1 in beyond what each states it is good to.
Total coils39 ± 1ProvisionalPhoto: Guntec's layout picture of the red set, as above
Photo 39 count ± 1 count used
Guntec's layout picture of the red set, as above, harvested
Scale: none: a count. Read by the crests of the spring's outline along each side of its axis (layout.py): 41 on the top edge with two pairs 6 px apart (a closed end coil's two strands, and one doubled crest) and the rest 11 to 13 px apart, 39 coils; 40 on the bottom edge with the last 7 px from its neighbour, 39. Both ends closed, as an enlargement shows (a2.jpg, b2.jpg). Redcon1's oblique picture of the whole spring (eabe3e83f28b) gave crests 8 to 48 px apart, the far side's coils showing between the near side's: not used
Wire diameter0.072 in ± 0.001 in 1.8 mmProvisionalWorked out: {std.carbine_action_spring.wire_d}
Worked out 0.072 in ± 0.001 in used
{std.carbine_action_spring.wire_d}, harvested
AN APPROXIMATION: the Army's drawing's wire for the rifle's action spring, the standard carbine spring's. No page states this one's, and at the layout picture's 38 px to the inch the wire is under 3 px.
Outside diameter of its coils0.94 in ± 0.015 in 23.9 mmConfirmedWorked out: {std.carbine_action_spring.od}
Worked out 0.94 in ± 0.015 in used
{std.carbine_action_spring.od}, harvested
The standard's: it goes over the buffer's step and inside the tube's 1.000 bore, as every carbine spring does.
Photo 0.94 in ± 0.04 in
Guntec's layout picture of the red set, as above, harvested
Scale: the tube beside it: 38.3 px/in. Read by the outline's crest to crest across its axis, the median over each pitch's span: 37.1 px at the lightest threshold of darkness and 35.1 at the darkest (od.py), 0.97 to 0.92 in; the ± is the threshold's
The standard's figure, which Guntec's picture of the spring bears out within its ±.
Its length as installed (a carbine buffer's seat to the set's tube's rear wall, bolt forward)6.972 in ± 0.03 in 177.1 mmProvisionalWorked out: {guntec-ar15-mil-spec-buffer-tube-gen-2.tube_front_behind_pin} + {guntec-ar15-mil-spec-buffer-tube-gen-2.tube_length} - {std.receiver_extension.carbine_rear_wall} + {std.ar15.upper_rear_face_x} - {std.carbine_buffer.head_thickness}
Worked out 6.972 in ± 0.03 in used
{guntec-ar15-mil-spec-buffer-tube-gen-2.tube_front_behind_pin} + {guntec-ar15-mil-spec-buffer-tube-gen-2.tube_length} - {std.receiver_extension.carbine_rear_wall} + {std.ar15.upper_rear_face_x} - {std.carbine_buffer.head_thickness}, harvested
What the spring is drawn at, in the set's own tube: from the rear face of a carbine buffer's head, whose front face rests at the upper receiver's rear face (the carrier's rear end, bolt forward), back to the rear wall inside Guntec's tube.
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
Receiver extension bore
- Receiver extensions
- BCM Milspec Carbine Receiver Extension (Buffer Tube) 6 Position, BCM MK2 Receiver Extension, Geissele Automatics Premium Mil-Spec Buffer Tube, Guntec USA AR-15 Mil-Spec Buffer Tube (Gen 2), SB Tactical SBPDW receiver extension, housing and integral castle nut, VLTOR RE-A5 7-Position Receiver Extension, MilSpec Diameter