Safety selector
Radian Weapons Talon 45/90 - 2 Lever Kit
An ambidextrous safety selector: a lever on each side of the rifle, a long one and a short one, each slid onto a dovetail on the shaft's end and held by a sprung stud. Radian: "The Talon™ 45/90 ambidextrous safety selector is a modular design that can be installed as a standard 90° or as a 45° short throw by simply rotating the shaft 180° inside the lower receiver. Selector levers install using a precision machined dovetail interface with spring-loaded retention stud to lock the lever in place – no screws to come loose or break." The kit: "1 - TALON Cylinder, 1 - Short Lever, 1 - Long Lever, 2 - TALON Spring & Detents, 1 - Talon Tool, 1 - Safety Selector Detent, 1 - Safety Selector Detent Spring".

- Weight
- 0.53 oz ± 0.05 oz Conflictpublished: Wing Tactical, Radian Talon Ambi 45/90 Safety Selector (2 Lever Set), a seller, read Oct 12, 2026Its sources span 0.04 oz to 1.92 oz.
- Lowest price
- $64.95 at Primary Arms, read Nov 21, 2026 (Black Anodized)
- Maker's number
- R0018
- Colours
- Black Anodized, Flat Dark Earth, Radian OD, Radian Grey
- Drawn as
- modelled
- Maker's page
- radianweapons.com
In “Aero M4E1 Enhanced, pencil barrel”, a build on the start page, as it is.
Its figures
Every figure the site draws and checks it by, with where it came from. Open one for each source's reading, and why one is used where they differ.
Diameter of the shaft that turns in the receiver0.372 in ± 0.003 in 9.5 mmConfirmedWorked out: {std.ar15.selector_shaft_d}
Worked out 0.37225 in ± 0.003 in used
{std.ar15.selector_shaft_d}, from the site owner
NOT RADIAN'S FIGURE: no page states one. The shaft turns in the standard's hole (.376 ±.001, std.ar15.selector_hole_d), so it is taken as the Army's own selector's diameter (drawing 9381367: .3730 -.0015, std.ar15.selector_shaft_d), with a ± as wide as the room there is under the hole. Every other size here is scaled by it.
Length of shaft between the faces that bear on the receiver's two sides0.961 in ± 0.009 in 24.4 mmCorroboratedPhoto: Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up
Photo 0.9613 in ± 0.009 in used
Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up, harvested
Scale: the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole. Read by the shaft's two shoulders, where its full diameter ends and each dovetail begins: x 1314.7 and 1849.5 on rows clear of the dovetails (y 296 and 480), 534.8 px
± for two edges a pixel soft and the scale's 0.7%.
Photo 0.9543 in ± 0.012 in
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by the long lever's inner face (x 354.5) to the far dovetail's end (x 1288.5), 934.0 px = 1.0232, less one dovetail's height (.dovetail_height)
The lever's inner face lies in the shaft's shoulder plane: the near cylinder shows .824 of a diameter long there, the far one .833.
Both shoulders seen bare, from straight above; the edge-on photo, read from a lever's inner face, agrees within 0.7%.
For this selector: between its two shoulders, which are the planes its two levers' inner faces lie in. .08 more than the receiver's .88: the levers stand about .04 off each side.
Height of each dovetail on the shaft's ends, from the shoulder0.069 in ± 0.004 in 1.8 mmProvisionalPhoto: Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up
Photo 0.0689 in ± 0.004 in used
Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up, harvested
Scale: the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole. Read by the shaft's ends (x 1277.1 and 1888.6) less its shoulders (1314.7 and 1849.5): 37.6 and 39.1 px, their mean
Width of each dovetail at its end (its widest)0.279 in ± 0.006 in 7.1 mmProvisionalPhoto: Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up
Photo 0.2786 in ± 0.006 in used
Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up, harvested
Scale: the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole. Read by the left dovetail across the shaft at x 1281, just inside its end: y 304.8 to 459.8, 155.0 px (the right one 148.7 at x 1884)
Width of each dovetail at the shoulder (its narrowest)0.206 in ± 0.006 in 5.2 mmProvisionalPhoto: Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up
Photo 0.206 in ± 0.006 in used
Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up, harvested
Scale: the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole. Read by the left dovetail across the shaft at x 1308 to 1312, beside the shoulder: 113.4 to 116.1 px (the right one 116.5 to 117.2)
Diameter of each lever's round head0.48 in ± 0.004 in 12.2 mmCorroboratedPhoto: Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up
Photo 0.4801 in ± 0.004 in used
Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up, harvested
Scale: the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole. Read by the short lever's head at its widest row (y 810 to 820): x 1239.5 to 1506.6, 267.1 px; its top at y 681, 133.5 above that row: a circle
Photo 0.4805 in ± 0.004 in
Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up, harvested
Scale: the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole. Read by the long lever's head at its widest row (y 810): x 1621.6 to 1888.9, 267.3 px
Photo 0.4804 in ± 0.005 in
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by the short lever's head, face-on, at its widest row (y 720): x 1394.1 to 1832.7, 438.5 px
Three readings in two photos within a thousandth: the standard selector's hub, .48 DIA.
The two levers' heads are one size. About the selector's axis: the hole the retention stud snaps into is at the head's middle (within .005), and the long lever's top stands .242 above the shaft's axis in the edge-on photo.
Width of each lever's thumb piece0.257 in ± 0.004 in 6.5 mmCorroboratedPhoto: Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up
Photo 0.2522 in ± 0.004 in
Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up, harvested
Scale: the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole. Read by the short lever's straight sides, rows y 960 to 1050: 140.3 px
Photo 0.2569 in ± 0.004 in used
Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up, harvested
Scale: the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole. Read by the long lever's straight sides, rows y 960 to 1160: 142.9 px
Photo 0.264 in ± 0.012 in
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by the short lever, face-on, rows y 1060 to 1100: 239 to 243 px, its left edge in its own shadow
The longer straight run, in the photo from straight above; the short lever's reads .005 less there, and the other photo's reading has a shadowed edge.
The lever's reach from the selector's axis to its tip0.797 in ± 0.008 in 20.2 mmCorroboratedPhoto: Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up
Photo 0.797 in ± 0.008 in used
Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up, harvested
Scale: the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole. Read by the LONG lever: its tip (y 1251.8) from its head's middle (y 808.5: its top at 674.2 and its widest row), 443.3 px
Photo 0.7817 in ± 0.01 in
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by the long lever edge-on: its tip at its inner face (y 1428) from the shaft's axis (y 714.5), 713.5 px
The tip's end is raked: at the lever's outer face it is .04 nearer the axis (y 1392).
Face-on, the tip unmistakable; the edge-on photo reads 1.9% less, inside the two ±.
The LONG lever, the one drawn on the left side. The short one is short_lever_reach.
The short lever's reach from the selector's axis to its tip0.609 in ± 0.008 in 15.5 mmCorroboratedPhoto: Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up
Photo 0.609 in ± 0.008 in used
Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up, harvested
Scale: the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole. Read by the SHORT lever: its tip (y 1153.3) from its head's middle (y 814.5), 338.8 px
Photo 0.5979 in ± 0.01 in
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by the short lever face-on: its tip (y 1270, above its shadow) from its head's middle (y 724.2), 545.8 px
The photo from straight above, without a shadow at the tip; the other reads 1.8% less.
How far the lever stands out from the receiver's side0.297 in ± 0.005 in 7.5 mmProvisionalPhoto: AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement
Photo 0.297 in ± 0.005 in used
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by the long lever edge-on, at its thickest, the thumb piece's top (rows y 820 to 920): its outer edge at x 83.4 to 84.3, 271.1 px out from its inner face
From the lever's OWN inner face to the highest of its thumb piece. The inner face itself stands about .04 off a standard receiver's side (shaft_length).
Thickness of the lever's head at its top edge0.13 in ± 0.006 in 3.3 mmProvisionalPhoto: AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement
Photo 0.1303 in ± 0.006 in used
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by the long lever edge-on at y 500, just under the head's top: its outer edge at x 235.6, 118.9 px out from the inner face
The head's outer face rises from here toward the thumb piece in a straight line: .151 at y 560, .179 at 640, .199 at 700.
Thickness of the lever's head where the thumb piece's step begins0.221 in ± 0.006 in 5.6 mmProvisionalPhoto: AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement
Photo 0.2206 in ± 0.006 in used
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by the long lever edge-on at y 760, .05 below the shaft's axis, the last row above the step: its outer edge at x 153.1, 201.4 px out
Thickness of the head at its rim, beside the middle band (the scooped facets' low edge)0.07 in ± 0.02 in 1.8 mmProvisionalPhoto: AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement
Photo 0.07 in ± 0.02 in used
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by the long lever edge-on, at the axis' height: the rim's lit band between the inner face and the shadowed scoop, about 64 px on a 1.83x crop
Read by eye on the crop: where the scoop's shadow begins.
Where the thumb piece's step rises from the head, from the selector's axis0.072 in ± 0.012 in 1.8 mmProvisionalPhoto: AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement
Photo 0.0718 in ± 0.012 in used
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by the long lever edge-on: the step between rows y 760 (.221 thick) and 800 (.294), its middle 65.5 px below the axis
Face-on (the other photo) the step is a point on the lever's centre line, .08 below the long lever's middle and .10 below the short one's, its two shoulders .1 further on.
Length of the point the thumb piece's step makes, from its tip on the centre line to its two shoulders0.09 in ± 0.015 in 2.3 mmProvisionalPhoto: Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up
Photo 0.09 in ± 0.015 in used
Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up, harvested
Scale: the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole. Read by the two levers face-on: the step's point and its shoulders, read on a 2.4x crop: .100 and .186 below the short lever's middle, .079 and .174 below the long one's; the mean of the two differences
Width of the head's raised middle band near its top edge0.13 in ± 0.02 in 3.3 mmProvisionalPhoto: Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up
Photo 0.13 in ± 0.02 in used
Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up, harvested
Scale: the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole. Read by the short lever's head, .17 above its middle: the band's two edges 36 px either side of the centre line on a 2.4x crop; they spread to the thumb piece's width at its shoulders
Length of the ramp by which the thumb piece's step rises0.044 in ± 0.012 in 1.1 mmProvisionalPhoto: AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement
Photo 0.044 in ± 0.012 in used
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by the long lever edge-on: .221 thick at row y 760 and .294 at y 800, 40 px on: a ramp, not a wall; the short lever face-on shows it as a lit facet on its centre line from y 755 to 815
Chamfer between a thumb piece's outer face and its sides0.024 in ± 0.006 in 0.6 mmProvisionalPhoto: AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement
Photo 0.024 in ± 0.006 in used
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by the short lever face-on, rows y 1040 to 1120: a shadowed band 22 to 25 px wide along its left edge, between its flat outer face and its outline
In the flat-lay photo a lighter band about 12 px wide (.022) runs along each edge of both levers.
Where the thumb piece's flat top ends and its taper to the tip begins, from the selector's axis0.225 in ± 0.015 in 5.7 mmProvisionalPhoto: AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement
Photo 0.225 in ± 0.015 in used
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by the long lever edge-on: the outer edge holds x 83.4 to 84.3 from y 820 to 920 and falls away below: y 920, 205.5 px below the axis
Thickness of the long lever's thumb piece near its tip0.222 in ± 0.006 in 5.6 mmProvisionalPhoto: AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement
Photo 0.2221 in ± 0.006 in used
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by the long lever edge-on at y 1380 (.729 from the axis), the last row above the end's rake: its outer edge at x 151.8, 202.7 px out
A straight taper from the flat top: .272 at y 1100, .255 at 1200, .239 at 1300.
How far the tip's end leans back from the inner face to the outer0.04 in ± 0.01 in 1 mmProvisionalPhoto: AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement
Photo 0.04 in ± 0.01 in used
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by the long lever's end edge-on: y 1428 at the inner face, 1404 at x 200 and about 1392 at the outer corner
Angle of each flank of the lever's pointed tip, from the lever's centre line43° ± 3°ProvisionalPhoto: Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up
Photo 43 deg ± 3 deg used
Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up, harvested
Scale: the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole. Read by the long lever's width over its last rows (112.4 px at y 1210, 56.7 at 1240): 1.86 px a row, .93 a side; the short lever's the same (114.3 at y 1110, 60.2 at 1140)
Width of the blunt end of the lever's point0.036 in ± 0.01 in 0.9 mmProvisionalPhoto: Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up
Photo 0.036 in ± 0.01 in used
Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up, harvested
Scale: the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole. Read by the long lever at y 1250, 2 px above its end: 25.5 px wide; the short at y 1150: 33.3 px, 3 px above its end
Radius of the hollow between the head and each side of the thumb piece0.07 in ± 0.02 in 1.8 mmProvisionalPhoto: Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up
Photo 0.07 in ± 0.02 in used
Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up, harvested
Scale: the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole. Read by the short lever's outline between y 900, where it is still the head's circle (206.1 px wide for a chord of 205.9), and y 955, where its sides run straight: the hollow leaves the circle .15 below the axis and meets the side .25 below it, as a radius of .07 does
Diameter of the hole in the head's middle that the retention stud snaps into0.059 in ± 0.008 in 1.5 mmProvisionalPhoto: AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement
Photo 0.059 in ± 0.008 in used
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by the short lever face-on: the dark hole at (1617, 724), about 54 px across and down
Grooves along each side face of a thumb piece3ProvisionalPhoto: AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement
Photo 3 count used
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: none (a count). Read by counted on the long lever's side face, the whole face in view: three dark lines along it at rows y 1000, 1100, 1200 and 1300
Primary Arms' two three-quarter views (596f7f263a07, 8d3b958078ae) show three on each side face of both levers.
Distance from one groove to the next0.061 in ± 0.004 in 1.5 mmProvisionalPhoto: AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement
Photo 0.0608 in ± 0.004 in used
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by the three grooves' shadowed walls on row y 1100: x 179, 234 and 290, 55.5 px apart (the same on rows 1000, 1200 and 1300)
The first groove's middle, in from the thumb piece's outer face0.08 in ± 0.006 in 2 mmProvisionalPhoto: AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement
Photo 0.08 in ± 0.006 in used
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by row y 1100: the outer edge at x 106.3, the first groove at 179, 72.7 px (72.4 on row 1000): the grooves run parallel to the outer face
Width of each groove0.026 in ± 0.006 in 0.7 mmProvisionalPhoto: AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement
Photo 0.026 in ± 0.006 in used
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by a groove's shadowed wall and its lit wall together on row y 1100: 21 to 27 px
A round-ended cut (a ball mill's): its depth isn't seen, and it is drawn as half its width.
Where the first two grooves begin, from the selector's axis0.182 in ± 0.012 in 4.6 mmProvisionalPhoto: AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement
Photo 0.182 in ± 0.012 in used
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by the two outer grooves' rounded upper ends at y 880, 166 px below the axis; the third, nearest the receiver, begins at y 938 (.245)
Where the grooves end, short of the lever's tip0.096 in ± 0.012 in 2.4 mmProvisionalPhoto: AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement
Photo 0.096 in ± 0.012 in used
AR15Discounts' picture of its Tungsten Grey variant, 71d8982d…jpg, 1920 x 1920: the long lever on the shaft's left end seen edge-on, the short lever face-on beside it; the black variant's picture, 2b204100d15a, is the same arrangement, harvested
Scale: the shaft in the same photo: 339.8 px across (columns 1000 to 1220) taken as .37225 (.shaft_d): 912.8 px/in; the lever's inner face is the straight edge at x 354.5, the shaft's axis at y 714.5. Read by the three grooves' lower ends at y 1340, 88 px above the long lever's tip at its inner face (y 1428)
Width of the groove down the head's outer face, from its top edge to the stud's hole0.042 in ± 0.01 in 1.1 mmProvisionalPhoto: Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up
Photo 0.042 in ± 0.01 in used
Primary Arms' R0018_02: the black kit laid out flat, from straight above, 2200 x 1467: the shaft on its side, the short lever at the left and the long at the right, both face-on, outer face up, harvested
Scale: the shaft in the same photo, on the same table: 207.1 px between its two edges (columns 1340 to 1460, where the white gives way to the shaft's lit edge) taken as .37225, the diameter of the Army's own selector (.shaft_d), which turns in the same .376 hole (std.ar15.selector_hole_d): 556.3 px/in. NOT scaled by the receiver's width: the shaft's shoulders are 534.8 px apart, and as .88 (std.ar15.lower_body_width) they would make its diameter .341, which doesn't turn in that hole. Read by the short lever's head, .17 above its middle: the groove's two walls 23 px apart on a 2.4x crop; they close toward the hole
What it goes with
By the way it mounts, and the figures each part on file states: a part whose figures say it doesn't fit is left out, and one whose fit can't be checked from what is published is marked. A check is against published figures, not a guarantee.
AR-15 safety selector
- Lower receivers
- Aero Precision M4E1 complete lower, A2 grip and M4 stock, Aero Precision M4E1 Stripped Lower Receiver, Battle Arms Development Workhorse stripped lower, BCM MK2 AR-15 Lower Receiver, Bear Creek Arsenal BC-15 Multi Caliber, Lower Receiver, Black Anodized, Geissele Automatics Super Duty AR-15 Lower Receiver - Stripped Lower, Palmetto State Armory AR-15 "Stealth" Stripped Lower Receiver
Prices on file
Each seller's latest reading of its own page: before tax and shipping, and not a quote. The pages are read again every night.
- Primary Arms $64.95 Black Anodized Nov 21, 2026, in stock that day
- Midwest Gun Works $64.95 Black Anodized Nov 21, 2026, in stock that day
- AR15Discounts $64.95 Black Anodized Nov 21, 2026, stock not said
- MidwayUSA $64.95 Black Anodized Nov 21, 2026, in stock that day
- Midwest Gun Works $69.95 Flat Dark Earth Nov 21, 2026, in stock that day
- Midwest Gun Works $69.95 Radian OD Nov 21, 2026, in stock that day
- Midwest Gun Works $69.95 Radian Grey Nov 21, 2026, in stock that day
- AR15Discounts $69.95 Flat Dark Earth Nov 21, 2026, stock not said
- AR15Discounts $69.95 Radian OD Nov 21, 2026, stock not said
- MidwayUSA $69.95 Flat Dark Earth Nov 21, 2026, in stock that day
- MidwayUSA $69.95 Radian OD Nov 21, 2026, in stock that day
- Right To Bear $64.95 Black Anodized Nov 21, 2026, out of stock that day
- Rifle Supply $66.99 Black Anodized Nov 21, 2026, out of stock that day